FRP COUNTER FLOW FT SERIES

COOLING TOWER

RYOWO (HOLDING) CO.,LTD.

Rm. 1218, Argyle Centre 1,
688 Nathan Road, Mongkok,
Kowloon, Hong Kong.

Tel. : (852) 2391-8381/5

Fax : (852) 2789-3802
Web site : http://www.ryowo.com
E-mail : [email protected]

ISO9001 : 2000 FM 40930

SHENZHEN RYOWO COOLING TOWER CO.,LTD.

Shaqicun, Songgang, Baoan,
Guangdong, China.

Tel. : (86-755) 2705 0346

Fax : (86-755) 2705 0376
E-mail : [email protected]
Postal Code : 518105
 STRUCTURE

MOTOR

REDUCER

FAN GUARD

MOTOR SUPPORT

FAN

CASING

SPRINKLER SYSTEM

FILLER

AIR INTAKE LOUVER

(OPTIONAL PARTS)

AIR INLET MESH

AIR INLET SUPPORT ASS'Y
FLOAT VALVE ASS'Y

FILLER SUPPORT ASS'Y BASIN

SPLASH MAT ASS'Y
LADDER ASS'Y
TOWER SUPPORT ASS'Y
AUXILIARY SUCTION TANK

P RINCIPLE OF OPERATION
Hot water is distributed over the filler through the low velocity automatic sprinkler system and is mixed with the
upward draft of ambient air causing evaporation and thus heat is removed from the water. The cooled water
falls into the basin and is pumped to the heat sources for recirculation.
AVAILABLE OPTIONAL ACCESSORIES

D ISCHARGE HOOD
This option is available on small models. It provides another direction of discharge air leaving the tower. It is made of
F.R.P. with services door and wiring mesh on the air outlet.

H IGH TEMPERATURE FILLER

For high temperature operation such as waste water treatment , P.P. filler can withstand up to 80 inlet water. (Special
arrangement should be made for other components, please contact us for details.)

S TAINLESS STEEL COMPONENTS

As an option, we can provide type 304 stainless steel major steel members, bolts and nuts.

T WO-SPEED MOTOR
As an option, two-speed motor can be provided in 4P/6P single winding configeration. A considerable reduction in
noise and energy management can be achieved.

F. R.P. AIR INLET LOUVER

Inlet louver constructed of F.R.P. material can be provided, which matches the rest of tower and prevents water spla-
shing out from the tower.

B ASIN HEATERS
Electric immersion heaters with thermostat and control box are available to keep the basin water from freezing in
sub-zero weather.

B ODY COLOR
Cooling tower installed on the roof of building may be barely noticeable from the ground, and a colored cooling tower
matching to building color will make it "good look".
 FT- 8/1000 COOLING TOWER SPEC.

FT- 8 FT- 10 FT- 15 FT- 20 FT- 25

FT- 30 FT- 40 FT- 50 FT- 60 FT- 80

FT- 100 FT- 125 FT- 150 FT- 175 FT- 200

FT- 225 FT- 250 FT- 300 FT- 350 FT- 400

FT- 500 FT- 600 FT- 700 FT- 800 FT- 1000
 FT-8 STANDARD COUNTER FLOW TYPE COOLING TOWER SPECIFICATION

Manufacturer RYOWO (HOLDING) CO., LTD.

Type Counter Flow Cooling Tower
Origin China

1 OVERALL DIMENSION 8 DESIGN CONDITION

Diameter (Max.) mm 920 Nominal Flow m3/hr 6.24
Height (Max.) mm 1560 Water Out Temp. 32°C
Height (w/o motor) mm 1390 Water In Temp. 37°C
Basin Dia. mm ø 920 Ambient Wet Bulb Temp. 27°C
Net Weight kgs 56 Make-up Water Rate 1.43%
Operating Weight kgs 140
9 SPRINKLER SYSTEM
2 MOTOR Sp Head Inlet (Dia) mm ø 40
Manufacturer Teco Tatung or Equivalent Sp Head Outlet (Dia x Qty) mm ø15x4
Type TEFC
Volt/Phase/Hz 220/380/3/50Hz 10 AIR INLET MESH
Output Power 1/4HP 0.18kw Material PVC
Pole P 6 Quantity Pcs 3
Speed rpm 970
Insulation Class E 11 PIPING
Protection IP44 Elbow mm ø 40
Full Load Power Factor 60.0% Inlet (Dia.) mm ø 40
Full Load Power Efficiency 60.0% Outlet (Dia.) mm ø 40
Service Factor 1.15 Drain (Dia.) mm ø 25
Starting Current Amp 8.4/4.74 Overflow (Dia.) mm ø 25
Full Load Current Amp 1.4/0.79 Float Valve (Dia.) mm ø 15
Frame Size No. 71M Make-up Valve (Dia.) mm N.A.
Shaft Diameter mm ø 18 Float Ball (Dia.) mm ø 125

3 FAN 12 INFILL
Type Axial Thickness mm 0.2
Air Volume m3/hr 4200 Overall Diameter mm ø 755
Speed rpm 970 Overall Height mm 480
Fan Diameter mm ø 550
Bore Diameter mm ø 18 13 MATERIAL
No. of Blades Pcs 4 Fan Hub ABS Plastic
Fan Blade ABS Plastic
4 TRANSMISSION Motor Support Hot Dip Galv. Steel
Type Direct Fan Guard (Optional) Hot Dip Galv. Steel
Gear Reducer Ratio N.A. Casing FRP
Motor Pulley N.A. Water Basin FRP
Fan Pulley N.A. Aux. Suction Tank N.A.
Vee Belt N.A. Sprinkler Head ABS Plastic
Sprinkler Pipe ABS Plastic
5 CASING Eliminator N.A.
Quantity Pcs 2 Air Inlet Louver (Optional) FRP
Air Inlet Stand HIPS Plastic
Ladder Assembly N.A.
Stand Pipe PVC Pipe
6 WATER BASIN Horizontal Pipe PVC Pipe
Quantity Pc 1 Strainer PP Plastic
Infill Support PVC Pipe
Infill PVC Film
Bolt & Nuts Electroplated

7 AUX. SUCTION TANK 14 Noise Level (SPL) dBA 45.5

Flange Standard N.A. Note: The SPLs are measured 16m horizontally from the edge of the
tower at 1.5m above the foundation level.
Nov 2002 Ft008e.xls
 FT-10 STANDARD COUNTER FLOW TYPE COOLING TOWER SPECIFICATION

Manufacturer RYOWO (HOLDING) CO., LTD.

Type Counter Flow Cooling Tower
Origin China

1 OVERALL DIMENSION 8 DESIGN CONDITION

Diameter (Max.) mm 920 Nominal Flow m3/hr 7.8
Height (Max.) mm 1700 Water Out Temp. 32°C
Height (w/o motor) mm 1530 Water In Temp. 37°C
Basin Dia. mm ø 920 Ambient Wet Bulb Temp. 27°C
Net Weight kgs 65 Make-up Water Rate 1.43%
Operating Weight kgs 150
9 SPRINKLER SYSTEM
2 MOTOR Sp Head Inlet (Dia) mm ø 40
Manufacturer Teco Tatung or Equivalent Sp Head Outlet (Dia x Qty) mm ø 15x4
Type TEFC
Volt/Phase/Hz 220/380/3/50Hz 10 AIR INLET MESH
Output Power 1/4HP 0.18kw Material PVC
Pole P 6 Quantity Pcs 3
Speed rpm 970
Insulation Class E 11 PIPING
Protection IP44 Elbow mm ø 40
Full Load Power Factor 60.0% Inlet (Dia.) mm ø 40
Full Load Power Efficiency 60.0% Outlet (Dia.) mm ø 40
Service Factor 1.15 Drain (Dia.) mm ø 25
Starting Current Amp 8.4/4.74 Overflow (Dia.) mm ø 25
Full Load Current Amp 1.4/0.79 Float Valve (Dia.) mm ø 15
Frame Size No. 71M Make-up Valve (Dia.) mm N.A.
Shaft Diameter mm ø 18 Float Ball (Dia.) mm ø 125

3 FAN 12 INFILL
Type Axial Thickness mm 0.2
Air Volume m3/hr 5100 Overall Diameter mm ø 755
Speed rpm 970 Overall Height mm 680
Fan Diameter mm ø 640
Bore Diameter mm ø 18 13 MATERIAL
No. of Blades Pcs 4 Fan Hub ABS Plastic
Fan Blade ABS Plastic
4 TRANSMISSION Motor Support Hot Dip Galv. Steel
Type Direct Fan Guard (Optional) Hot Dip Galv. Steel
Gear Reducer Ratio N.A. Casing FRP
Motor Pulley N.A. Water Basin FRP
Fan Pulley N.A. Aux. Suction Tank N.A.
Vee Belt N.A. Sprinkler Head ABS Plastic
Sprinkler Pipe ABS Plastic
5 CASING Eliminator N.A.
Quantity Pcs 2 Air Inlet Louver (Optional) FRP
Air Inlet Stand HIPS Plastic
Ladder Assembly N.A.
Stand Pipe PVC Pipe
6 WATER BASIN Horizontal Pipe PVC Pipe
Quantity Pc 1 Strainer PP Plastic
Infill Support PVC Pipe
Infill PVC Film
Bolt & Nuts Electroplated

7 AUX. SUCTION TANK 14 Noise Level (SPL) dBA 47

Flange Standard N.A. Note: The SPLs are measured 16m horizontally from the edge of the
tower at 1.5m above the foundation level.
Nov 2002 Ft010e.xls
 FT-15 STANDARD COUNTER FLOW TYPE COOLING TOWER SPECIFICATION

Manufacturer RYOWO (HOLDING) CO., LTD.

Type Counter Flow Cooling Tower
Origin China

1 OVERALL DIMENSION 8 DESIGN CONDITION

Diameter (Max.) mm 1160 Nominal Flow m3/hr 11.7
Height (Max.) mm 1585 Water Out Temp. 32°C
Height (w/o motor) mm 1395 Water In Temp. 37°C
Basin Dia. mm ø 1160 Ambient Wet Bulb Temp. 27°C
Net Weight kgs 75 Make-up Water Rate 1.43%
Operating Weight kgs 200
9 SPRINKLER SYSTEM
2 MOTOR Sp Head Inlet (Dia) mm ø 50
Manufacturer Teco Tatung or Equivalent Sp Head Outlet (Dia x Qty) mm ø 20x4
Type TEFC
Volt/Phase/Hz 220/380/3/50Hz 10 AIR INLET MESH
Output Power 1/2HP 0.37kw Material PVC
Pole P 6 Quantity Pcs 3
Speed rpm 970
Insulation Class E 11 PIPING
Protection IP44 Elbow mm ø 50
Full Load Power Factor 67.0% Inlet (Dia.) mm ø 50
Full Load Power Efficiency 63.0% Outlet (Dia.) mm ø 50
Service Factor 1.15 Drain (Dia.) mm ø 25
Starting Current Amp 13.86/8.04 Overflow (Dia.) mm ø 25
Full Load Current Amp 2.31/1.34 Float Valve (Dia.) mm ø 15
Frame Size No. 80M Make-up Valve (Dia.) mm N.A.
Shaft Diameter mm ø 18 Float Ball (Dia.) mm ø 125

3 FAN 12 INFILL
Type Axial Thickness mm 0.2
Air Volume m3/hr 8400 Overall Diameter mm ø 1005
Speed rpm 970 Overall Height mm 480
Fan Diameter mm ø 640
Bore Diameter mm ø 18 13 MATERIAL
No. of Blades Pcs 4 Fan Hub ABS Plastic
Fan Blade ABS Plastic
4 TRANSMISSION Motor Support Hot Dip Galv. Steel
Type Direct Fan Guard (Optional) Hot Dip Galv. Steel
Gear Reducer Ratio N.A. Casing FRP
Motor Pulley N.A. Water Basin FRP
Fan Pulley N.A. Aux. Suction Tank N.A.
Vee Belt N.A. Sprinkler Head ABS Plastic
Sprinkler Pipe ABS Plastic
5 CASING Eliminator N.A.
Quantity Pcs 3 Air Inlet Louver (Optional) FRP
Air Inlet Stand HIPS Plastic
Ladder Assembly N.A.
Stand Pipe PVC Pipe
6 WATER BASIN Horizontal Pipe PVC Pipe
Quantity Pc 1 Strainer PP Plastic
Infill Support Hot Dip Galv. Steel
Infill PVC Film
Bolt & Nuts Electroplated

7 AUX. SUCTION TANK 14 Noise Level (SPL) dBA 48

Flange Standard N.A. Note: The SPLs are measured 16m horizontally from the edge of the
tower at 1.5m above the foundation level.
Nov 2002 Ft015e.xls
 FT-20 STANDARD COUNTER FLOW TYPE COOLING TOWER SPECIFICATION

Manufacturer RYOWO (HOLDING) CO., LTD.

Type Counter Flow Cooling Tower
Origin China

1 OVERALL DIMENSION 8 DESIGN CONDITION

Diameter (Max.) mm 1160 Nominal Flow m3/hr 15.6
Height (Max.) mm 1835 Water Out Temp. 32°C
Height (w/o motor) mm 1645 Water In Temp. 37°C
Basin Dia. mm ø 1160 Ambient Wet Bulb Temp. 27°C
Net Weight kgs 85 Make-up Water Rate 1.43%
Operating Weight kgs 210
9 SPRINKLER SYSTEM
2 MOTOR Sp Head Inlet (Dia) mm ø 50
Manufacturer Teco Tatung or Equivalent Sp Head Outlet (Dia x Qty) mm ø 20x4
Type TEFC
Volt/Phase/Hz 220/380/3/50Hz 10 AIR INLET MESH
Output Power 1/2HP 0.37kw Material PVC
Pole P 6 Quantity Pcs 3
Speed rpm 970
Insulation Class E 11 PIPING
Protection IP44 Elbow mm ø 50
Full Load Power Factor 67.0% Inlet (Dia.) mm ø 50
Full Load Power Efficiency 63.0% Outlet (Dia.) mm ø 50
Service Factor 1.15 Drain (Dia.) mm ø 25
Starting Current Amp 13.86/8.04 Overflow (Dia.) mm ø 25
Full Load Current Amp 2.31/1.34 Float Valve (Dia.) mm ø 15
Frame Size No. 80M Make-up Valve (Dia.) mm N.A.
Shaft Diameter mm ø 18 Float Ball (Dia.) mm ø 125

3 FAN 12 INFILL
Type Axial Thickness mm 0.2
Air Volume m3/hr 9600 Overall Diameter mm ø 1005
Speed rpm 970 Overall Height mm 680
Fan Diameter mm ø 770
Bore Diameter mm ø 18 13 MATERIAL
No. of Blades Pcs 4 Fan Hub ABS Plastic
Fan Blade ABS Plastic
4 TRANSMISSION Motor Support Hot Dip Galv. Steel
Type Direct Fan Guard (Optional) Hot Dip Galv. Steel
Gear Reducer Ratio N.A. Casing FRP
Motor Pulley N.A. Water Basin FRP
Fan Pulley N.A. Aux. Suction Tank N.A.
Vee Belt N.A. Sprinkler Head ABS Plastic
Sprinkler Pipe ABS Plastic
5 CASING Eliminator N.A.
Quantity Pcs 3 Air Inlet Louver (Optional) FRP
Air Inlet Stand HIPS Plastic
Ladder Assembly N.A.
Stand Pipe PVC Pipe
6 WATER BASIN Horizontal Pipe PVC Pipe
Quantity Pc 1 Strainer PP Plastic
Infill Support Hot Dip Galv. Steel
Infill PVC Film
Bolt & Nuts Electroplated

7 AUX. SUCTION TANK 14 Noise Level (SPL) dBA 50

Flange Standard N.A. Note: The SPLs are measured 16m horizontally from the edge of the
tower at 1.5m above the foundation level.
Nov 2002 Ft020e.xls
 FT-25 STANDARD COUNTER FLOW TYPE COOLING TOWER SPECIFICATION

Manufacturer RYOWO (HOLDING) CO., LTD.

Type Counter Flow Cooling Tower
Origin China

1 OVERALL DIMENSION 8 DESIGN CONDITION

Diameter (Max.) mm 1490 Nominal Flow m3/hr 19.5
Height (Max.) mm 1945 Water Out Temp. 32°C
Height (w/o motor) mm 1760 Water In Temp. 37°C
Basin Dia. mm ø 1490 Ambient Wet Bulb Temp. 27°C
Net Weight kgs 105 Make-up Water Rate 1.43%
Operating Weight kgs 290
9 SPRINKLER SYSTEM
2 MOTOR Sp Head Inlet (Dia) mm ø 80
Manufacturer Teco Tatung or Equivalent Sp Head Outlet (Dia x Qty) mm ø 40x4
Type TEFC
Volt/Phase/Hz 220/380/3/50Hz 10 AIR INLET MESH
Output Power 1HP 0.75kw Material PVC
Pole P 6 Quantity Pcs 4
Speed rpm 970
Insulation Class E 11 PIPING
Protection IP44 Elbow mm ø 80
Full Load Power Factor 70.0% Inlet (Dia.) mm ø 80
Full Load Power Efficiency 71.0% Outlet (Dia.) mm ø 80
Service Factor 1.15 Drain (Dia.) mm ø 25
Starting Current Amp 23.64/13.68 Overflow (Dia.) mm ø 25
Full Load Current Amp 3.94/2.28 Float Valve (Dia.) mm ø 15
Frame Size No. 90L Make-up Valve (Dia.) mm N.A.
Shaft Diameter mm ø 20 Float Ball (Dia.) mm ø 125

3 FAN 12 INFILL
Type Axial Thickness mm 0.2
Air Volume m3/hr 13800 Overall Diameter mm ø 1290
Speed rpm 970 Overall Height mm 580
Fan Diameter mm ø 770
Bore Diameter mm ø 20 13 MATERIAL
No. of Blades Pcs 4 Fan Hub ABS Plastic
Fan Blade ABS Plastic
4 TRANSMISSION Motor Support Hot Dip Galv. Steel
Type Direct Fan Guard (Optional) Hot Dip Galv. Steel
Gear Reducer Ratio N.A. Casing FRP
Motor Pulley N.A. Water Basin FRP
Fan Pulley N.A. Aux. Suction Tank N.A.
Vee Belt N.A. Sprinkler Head ABS Plastic
Sprinkler Pipe PVC Pipe
5 CASING Eliminator FRP
Quantity Pcs 3 Air Inlet Louver (Optional) FRP
Air Inlet Stand HIPS Plastic
Ladder Assembly N.A.
Stand Pipe PVC Pipe
6 WATER BASIN Horizontal Pipe PVC Pipe
Quantity Pc 1 Strainer PP Plastic
Infill Support Hot Dip Galv. Steel
Infill PVC Film
Bolt & Nuts Electroplated

7 AUX. SUCTION TANK 14 Noise Level (SPL) dBA 52

Flange Standard N.A. Note: The SPLs are measured 16m horizontally from the edge of the
tower at 1.5m above the foundation level.
Nov 2002 Ft025e.xls
 FT-30 STANDARD COUNTER FLOW TYPE COOLING TOWER SPECIFICATION

Manufacturer RYOWO (HOLDING) CO., LTD.

Type Counter Flow Cooling Tower
Origin China

1 OVERALL DIMENSION 8 DESIGN CONDITION

Diameter (Max.) mm 1660 Nominal Flow m3/hr 23.4
Height (Max.) mm 1885 Water Out Temp. 32°C
Height (w/o motor) mm 1720 Water In Temp. 37°C
Basin Dia. mm ø 1660 Ambient Wet Bulb Temp. 27°C
Net Weight kgs 130 Make-up Water Rate 1.43%
Operating Weight kgs 370
9 SPRINKLER SYSTEM
2 MOTOR Sp Head Inlet (Dia) mm ø 80
Manufacturer Teco Tatung or Equivalent Sp Head Outlet (Dia x Qty) mm ø 40x4
Type TEFC
Volt/Phase/Hz 220/380/3/50Hz 10 AIR INLET MESH
Output Power 1HP 0.75kw Material PVC
Pole P 6 Quantity Pcs 6
Speed rpm 970
Insulation Class E 11 PIPING
Protection IP44 Elbow mm ø 80
Full Load Power Factor 70.0% Inlet (Dia.) mm ø 80
Full Load Power Efficiency 71.0% Outlet (Dia.) mm ø 80
Service Factor 1.15 Drain (Dia.) mm ø 25
Starting Current Amp 23.64/13.68 Overflow (Dia.) mm ø 25
Full Load Current Amp 3.94/2.28 Float Valve (Dia.) mm ø 15
Frame Size No. 90L Make-up Valve (Dia.) mm N.A.
Shaft Diameter mm ø 20 Float Ball (Dia.) mm ø 125

3 FAN 12 INFILL
Type Axial Thickness mm 0.2
Air Volume m3/hr 16800 Overall Diameter mm ø 1410
Speed rpm 970 Overall Height mm 580
Fan Diameter mm ø 770
Bore Diameter mm ø 20 13 MATERIAL
No. of Blades Pcs 4 Fan Hub ABS Plastic
Fan Blade ABS Plastic
4 TRANSMISSION Motor Support Hot Dip Galv. Steel
Type Direct Fan Guard (Optional) Hot Dip Galv. Steel
Gear Reducer Ratio N.A. Casing FRP
Motor Pulley N.A. Water Basin FRP
Fan Pulley N.A. Aux. Suction Tank N.A.
Vee Belt N.A. Sprinkler Head ABS Plastic
Sprinkler Pipe PVC Pipe
5 CASING Eliminator FRP
Quantity Pcs 3 Air Inlet Louver (Optional) FRP
Air Inlet Stand HIPS Plastic
Ladder Assembly N.A.
Stand Pipe PVC Pipe
6 WATER BASIN Horizontal Pipe PVC Pipe
Quantity Pc 1 Strainer PP Plastic
Infill Support Hot Dip Galv. Steel
Infill PVC Film
Bolt & Nuts Electroplated

7 AUX. SUCTION TANK 14 Noise Level (SPL) dBA 54

Flange Standard N.A. Note: The SPLs are measured 16m horizontally from the edge of the
tower at 1.5m above the foundation level.
Nov 2002 Ft030e.xls
 FT-40 STANDARD COUNTER FLOW TYPE COOLING TOWER SPECIFICATION

Manufacturer RYOWO (HOLDING) CO., LTD.

Type Counter Flow Cooling Tower
Origin China

1 OVERALL DIMENSION 8 DESIGN CONDITION

Diameter (Max.) mm 1660 Nominal Flow m3/hr 31.2
Height (Max.) mm 2035 Water Out Temp. 32°C
Height (w/o motor) mm 1785 Water In Temp. 37°C
Basin Dia. mm ø 1660 Ambient Wet Bulb Temp. 27°C
Net Weight kgs 150 Make-up Water Rate 1.43%
Operating Weight kgs 390
9 SPRINKLER SYSTEM
2 MOTOR Sp Head Inlet (Dia) mm ø 80
Manufacturer Teco Tatung or Equivalent Sp Head Outlet (Dia x Qty) mm ø 40x4
Type TEFC
Volt/Phase/Hz 220/380/3/50Hz 10 AIR INLET MESH
Output Power 2HP 1.5kw Material PVC
Pole P 6 Quantity Pcs 6
Speed rpm 970
Insulation Class E 11 PIPING
Protection IP44 Elbow mm ø 80
Full Load Power Factor 71.5% Inlet (Dia.) mm ø 80
Full Load Power Efficiency 75.5% Outlet (Dia.) mm ø 80
Service Factor 1.15 Drain (Dia.) mm ø 25
Starting Current Amp 43.5/25.2 Overflow (Dia.) mm ø 25
Full Load Current Amp 7.25/4.2 Float Valve (Dia.) mm ø 15
Frame Size No. 100L Make-up Valve (Dia.) mm N.A.
Shaft Diameter mm ø 20 Float Ball (Dia.) mm ø 125

3 FAN 12 INFILL
Type Axial Thickness mm 0.2
Air Volume m3/hr 19800 Overall Diameter mm ø 1410
Speed rpm 970 Overall Height mm 680
Fan Diameter mm ø 930
Bore Diameter mm ø 20 13 MATERIAL
No. of Blades Pcs 4 Fan Hub ABS Plastic
Fan Blade ABS Plastic
4 TRANSMISSION Motor Support Hot Dip Galv. Steel
Type Direct Fan Guard (Optional) Hot Dip Galv. Steel
Gear Reducer Ratio N.A. Casing FRP
Motor Pulley N.A. Water Basin FRP
Fan Pulley N.A. Aux. Suction Tank N.A.
Vee Belt N.A. Sprinkler Head ABS Plastic
Sprinkler Pipe PVC Pipe
5 CASING Eliminator FRP
Quantity Pcs 3 Air Inlet Louver (Optional) FRP
Air Inlet Stand HIPS Plastic
Ladder Assembly N.A.
Stand Pipe PVC Pipe
6 WATER BASIN Horizontal Pipe PVC Pipe
Quantity Pc 1 Strainer PP Plastic
Infill Support Hot Dip Galv. Steel
Infill PVC Film
Bolt & Nuts Electroplated

7 AUX. SUCTION TANK 14 Noise Level (SPL) dBA 58

Flange Standard N.A. Note: The SPLs are measured 16m horizontally from the edge of the
tower at 1.5m above the foundation level.
Nov 2002 Ft040e.xls
 FT-50 STANDARD COUNTER FLOW TYPE COOLING TOWER SPECIFICATION

Manufacturer RYOWO (HOLDING) CO., LTD.

Type Counter Flow Cooling Tower
Origin China

1 OVERALL DIMENSION 8 DESIGN CONDITION

Diameter (Max.) mm 1890 Nominal Flow m3/hr 39
Height (Max.) mm 2110 Water Out Temp. 32°C
Height (w/o motor) mm 1860 Water In Temp. 37°C
Basin Dia. mm ø 1890 Ambient Wet Bulb Temp. 27°C
Net Weight kgs 180 Make-up Water Rate 1.43%
Operating Weight kgs 550
9 SPRINKLER SYSTEM
2 MOTOR Sp Head Inlet (Dia) mm ø 80
Manufacturer Teco Tatung or Equivalent Sp Head Outlet (Dia x Qty) mm ø 40x4
Type TEFC
Volt/Phase/Hz 220/380/3/50Hz 10 AIR INLET MESH
Output Power 2HP 1.5kw Material PVC
Pole P 6 Quantity Pcs 8
Speed rpm 970
Insulation Class E 11 PIPING
Protection IP44 Elbow mm ø 80
Full Load Power Factor 71.5% Inlet (Dia.) mm ø 80
Full Load Power Efficiency 75.5% Outlet (Dia.) mm ø 80
Service Factor 1.15 Drain (Dia.) mm ø 25
Starting Current Amp 43.5/25.2 Overflow (Dia.) mm ø 25
Full Load Current Amp 7.25/4.2 Float Valve (Dia.) mm ø 15
Frame Size No. 100L Make-up Valve (Dia.) mm N.A.
Shaft Diameter mm ø 20 Float Ball (Dia.) mm ø 125

3 FAN 12 INFILL
Type Axial Thickness mm 0.2
Air Volume m3/hr 25200 Overall Diameter mm ø 1685
Speed rpm 970 Overall Height mm 580
Fan Diameter mm ø 930
Bore Diameter mm ø 20 13 MATERIAL
No. of Blades Pcs 4 Fan Hub ABS Plastic
Fan Blade ABS Plastic
4 TRANSMISSION Motor Support Hot Dip Galv Steel
Type Direct Fan Guard (Optional) Hot Dip Galv Steel
Gear Reducer Ratio N.A. Casing FRP
Motor Pulley N.A. Water Basin FRP
Fan Pulley N.A. Aux. Suction Tank N.A.
Vee Belt N.A. Sprinkler Head ABS Plastic
Sprinkler Pipe PVC Pipe
5 CASING Eliminator FRP
Quantity Pcs 4 Air Inlet Louver (Optional) FRP
Air Inlet Stand HIPS Plastic
Ladder Assembly N.A.
Stand Pipe PVC Pipe
6 WATER BASIN Horizontal Pipe PVC Pipe
Quantity Pc 1 Strainer PP Plastic
Infill Support Hot Dip Galv Steel
Infill PVC Film
Bolt & Nuts Electroplated

7 AUX. SUCTION TANK 14 Noise Level (SPL) dBA 59

Flange Standard N.A. Note: The SPLs are measured 16m horizontally from the edge of the
tower at 1.5m above the foundation level.
Nov 2002 Ft050e.xls
 FT-60 STANDARD COUNTER FLOW TYPE COOLING TOWER SPECIFICATION

Manufacturer RYOWO (HOLDING) CO., LTD.

Type Counter Flow Cooling Tower
Origin China

1 OVERALL DIMENSION 8 DESIGN CONDITION

Diameter (Max.) mm 2100 Nominal Flow m3/hr 46.8
Height (Max.) mm 2300 Water Out Temp. 32°C
Height (w/o motor) mm 1980 Water In Temp. 37°C
Basin Dia. mm ø 2100 Ambient Wet Bulb Temp. 27°C
Net Weight kgs 250 Make-up Water Rate 1.43%
Operating Weight kgs 840
9 SPRINKLER SYSTEM
2 MOTOR Sp Head Inlet (Dia) mm ø 100
Manufacturer Teco Tatung or Equivalent Sp Head Outlet (Dia x Qty) mm ø 40x6
Type TEFC
Volt/Phase/Hz 220/380/3/50Hz 10 AIR INLET MESH
Output Power 2HP 1.5kw Material PVC
Pole P 8 Quantity Pcs 8
Speed rpm 750
Insulation Class E 11 PIPING
Protection IP44 Elbow mm ø 100
Full Load Power Factor 68.5% Inlet (Dia.) mm ø 100
Full Load Power Efficiency 73.5% Outlet (Dia.) mm ø 100
Service Factor 1.15 Drain (Dia.) mm ø 25
Starting Current Amp 46.8/27 Overflow (Dia.) mm ø 25
Full Load Current Amp 7.8/4.5 Float Valve (Dia.) mm ø 20
Frame Size No. 112M Make-up Valve (Dia.) mm N.A.
Shaft Diameter mm ø 28 Float Ball (Dia.) mm ø 125

3 FAN 12 INFILL
Type Axial Thickness mm 0.2
Air Volume m3/hr 27000 Overall Diameter mm ø 1905
Speed rpm 750 Overall Height mm 580
Fan Diameter mm ø 1200
Bore Diameter mm ø 28 13 MATERIAL
No. of Blades Pcs 4 Fan Hub Al. Alloy
Fan Blade FRP
4 TRANSMISSION Motor Support Hot Dip Galv. Steel
Type Direct Fan Guard Hot Dip Galv. Steel
Gear Reducer Ratio N.A. Casing FRP
Motor Pulley N.A. Water Basin FRP
Fan Pulley N.A. Aux. Suction Tank N.A.
Vee Belt N.A. Sprinkler Head ABS Plastic
Sprinkler Head (Optional) Al. Alloy
5 CASING Sprinkler Pipe PVC Pipe
Quantity Pcs 4 Eliminator FRP
Air Inlet Louver (Optional) FRP
Air Inlet Stand Hot Dip Galv. Steel
Ladder Assembly Hot Dip Galv. Steel
6 WATER BASIN Stand Pipe PVC Pipe
Quantity Pc 1 Horizontal Pipe PVC Pipe
Strainer PP Plastic
Infill Support Hot Dip Galv. Steel
Infill PVC Film
Bolt & Nuts Electroplated
7 AUX. SUCTION TANK
Flange Standard N.A. 14 Noise Level (SPL) dBA 58
Note: The SPLs are measured 16m horizontally from the edge of the
tower at 1.5m above the foundation level.
Nov 2002 Ft060e.xls
 FT-80 STANDARD COUNTER FLOW TYPE COOLING TOWER SPECIFICATION

Manufacturer RYOWO (HOLDING) CO., LTD.

Type Counter Flow Cooling Tower
Origin China

1 OVERALL DIMENSION 8 DESIGN CONDITION

Diameter (Max.) mm 2100 Nominal Flow m3/hr 62.4
Height (Max.) mm 2475 Water Out Temp. 32°C
Height (w/o motor) mm 2155 Water In Temp. 37°C
Basin Dia. mm ø 2100 Ambient Wet Bulb Temp. 27°C
Net Weight kgs 270 Make-up Water Rate 1.43%
Operating Weight kgs 860
9 SPRINKLER SYSTEM
2 MOTOR Sp Head Inlet (Dia) mm ø 100
Manufacturer Teco Tatung or Equivalent Sp Head Outlet (Dia x Qty) mm ø 40x6
Type TEFC
Volt/Phase/Hz 220/380/3/50Hz 10 AIR INLET MESH
Output Power 2HP 1.5kw Material PVC
Pole P 8 Quantity Pcs 8
Speed rpm 750
Insulation Class E 11 PIPING
Protection IP44 Elbow mm ø 100
Full Load Power Factor 68.5% Inlet (Dia.) mm ø 100
Full Load Power Efficiency 73.5% Outlet (Dia.) mm ø 100
Service Factor 1.15 Drain (Dia.) mm ø 25
Starting Current Amp 46.8/27 Overflow (Dia.) mm ø 25
Full Load Current Amp 7.8/4.5 Float Valve (Dia.) mm ø 20
Frame Size No. 112M Make-up Valve (Dia.) mm N.A.
Shaft Diameter mm ø 28 Float Ball (Dia.) mm ø 125

3 FAN 12 INFILL
Type Axial Thickness mm 0.2
Air Volume m3/hr 42000 Overall Diameter mm ø 1905
Speed rpm 750 Overall Height mm 680
Fan Diameter mm ø 1200
Bore Diameter mm ø 28 13 MATERIAL
No. of Blades Pcs 4 Fan Hub Al. Alloy
Fan Blade FRP
4 TRANSMISSION Motor Support Hot Dip Galv. Steel
Type Direct Fan Guard Hot Dip Galv. Steel
Gear Reducer Ratio N.A. Casing FRP
Motor Pulley N.A. Water Basin FRP
Fan Pulley N.A. Aux. Suction Tank N.A.
Vee Belt N.A. Sprinkler Head ABS Plastic
Sprinkler Head (Optional) Al. Alloy
5 CASING Sprinkler Pipe PVC Pipe
Quantity Pcs 4 Eliminator FRP
Air Inlet Louver (Optional) FRP
Air Inlet Stand Hot Dip Galv. Steel
Ladder Assembly Hot Dip Galv. Steel
6 WATER BASIN Stand Pipe PVC Pipe
Quantity Pc 1 Horizontal Pipe PVC Pipe
Strainer PP Plastic
Infill Support Hot Dip Galv. Steel
Infill PVC Film
Bolt & Nuts Electroplated
7 AUX. SUCTION TANK
Flange Standard N.A. 14 Noise Level (SPL) dBA 59
Note: The SPLs are measured 16m horizontally from the edge of the
tower at 1.5m above the foundation level.
Nov 2002 Ft080e.xls
 FT-100 STANDARD COUNTER FLOW TYPE COOLING TOWER SPECIFICATION

Manufacturer RYOWO (HOLDING) CO., LTD.

Type Counter Flow Cooling Tower
Origin China

1 OVERALL DIMENSION 8 DESIGN CONDITION

Diameter (Max.) mm 2900 Nominal Flow m3/hr 78
Height (Max.) mm 2910 Water Out Temp. 32°C
Height (w/o motor) mm 2590 Water In Temp. 37°C
Basin Dia. mm ø 2900 Ambient Wet Bulb Temp. 27°C
Net Weight kgs 500 Make-up Water Rate 1.43%
Operating Weight kgs 1600
9 SPRINKLER SYSTEM
2 MOTOR Sp Head Inlet (Dia) mm ø 125
Manufacturer Teco Tatung or Equivalent Sp Head Outlet (Dia x Qty) mm ø 65x4
Type TEFC
Volt/Phase/Hz 220/380/3/50Hz 10 AIR INLET MESH
Output Power 3HP 2.2kw Material PVC
Pole P 8 Quantity Pcs 12
Speed rpm 750
Insulation Class B 11 PIPING
Protection IP44 Elbow mm N.A.
Full Load Power Factor 72.5% Inlet (Dia.) mm ø 125
Full Load Power Efficiency 81.0% Outlet (Dia.) mm ø 125
Service Factor 1.15 Drain (Dia.) mm ø 50
Starting Current Amp 60/34.8 Overflow (Dia.) mm ø 50
Full Load Current Amp 10/5.8 Float Valve (Dia.) mm ø 20
Frame Size No. 132S Make-up Valve (Dia.) mm N.A.
Shaft Diameter mm ø 34 Float Ball (Dia.) mm ø 125

3 FAN 12 INFILL
Type Axial Thickness mm 0.2
Air Volume m3/hr 49800 Overall Diameter mm ø 2710
Speed rpm 750 Overall Height mm 480
Fan Diameter mm ø 1500
Bore Diameter mm ø 34 13 MATERIAL
No. of Blades Pcs 4 Fan Hub Al. Alloy
Fan Blade FRP
4 TRANSMISSION Motor Support Hot Dip Galv. Steel
Type Direct Fan Guard Hot Dip Galv. Steel
Gear Reducer Ratio N.A. Casing FRP
Motor Pulley N.A. Water Basin FRP
Fan Pulley N.A. Aux. Suction Tank FRP
Vee Belt N.A. Sprinkler Head Al. Alloy
Sprinkler Pipe PVC Pipe
5 CASING Eliminator FRP
Quantity Pcs 6 Air Inlet Louver (Optional) FRP
Air Inlet Stand Hot Dip Galv. Steel
Ladder Assembly Hot Dip Galv. Steel
Stand Pipe PVC Pipe
6 WATER BASIN Horizontal Pipe N.A.
Quantity Pcs 3 Strainer SS 304
Infill Support Hot Dip Galv. Steel
Infill PVC Film
Bolt & Nuts Electroplated

7 AUX. SUCTION TANK 14 Noise Level (SPL) dBA 61

Flange Standard JIS 5kg/cm2 Note: The SPLs are measured 16m horizontally from the edge of the
tower at 1.5m above the foundation level.
Nov 2002 Ft100e.xls
 FT-125 STANDARD COUNTER FLOW TYPE COOLING TOWER SPECIFICATION

Manufacturer RYOWO (HOLDING) CO., LTD.

Type Counter Flow Cooling Tower
Origin China

1 OVERALL DIMENSION 8 DESIGN CONDITION

Diameter (Max.) mm 2900 Nominal Flow m3/hr 97.8
Height (Max.) mm 3110 Water Out Temp. 32°C
Height (w/o motor) mm 2790 Water In Temp. 37°C
Basin Dia. mm ø 2900 Ambient Wet Bulb Temp. 27°C
Net Weight kgs 540 Make-up Water Rate 1.43%
Operating Weight kgs 1640
9 SPRINKLER SYSTEM
2 MOTOR Sp Head Inlet (Dia) mm ø 125
Manufacturer Teco Tatung or Equivalent Sp Head Outlet (Dia x Qty) mm ø 65x4
Type TEFC
Volt/Phase/Hz 220/380/3/50Hz 10 AIR INLET MESH
Output Power 3HP 2.2kw Material PVC
Pole P 8 Quantity Pcs 12
Speed rpm 750
Insulation Class B 11 PIPING
Protection IP44 Elbow mm N.A.
Full Load Power Factor 72.5% Inlet (Dia.) mm ø 125
Full Load Power Efficiency 81.0% Outlet (Dia.) mm ø 125
Service Factor 1.15 Drain (Dia.) mm ø 50
Starting Current Amp 60/34.8 Overflow (Dia.) mm ø 50
Full Load Current Amp 10/5.8 Float Valve (Dia.) mm ø 20
Frame Size No. 132S Make-up Valve (Dia.) mm N.A.
Shaft Diameter mm ø 34 Float Ball (Dia.) mm ø 125

3 FAN 12 INFILL
Type Axial Thickness mm 0.2
Air Volume m3/hr 57000 Overall Diameter mm ø 2710
Speed rpm 750 Overall Height mm 580
Fan Diameter mm ø 1500
Bore Diameter mm ø 34 13 MATERIAL
No. of Blades Pcs 4 Fan Hub Al. Alloy
Fan Blade FRP
4 TRANSMISSION Motor Support Hot Dip Galv. Steel
Type Direct Fan Guard Hot Dip Galv. Steel
Gear Reducer Ratio N.A. Casing FRP
Motor Pulley N.A. Water Basin FRP
Fan Pulley N.A. Aux. Suction Tank FRP
Vee Belt N.A. Sprinkler Head Al. Alloy
Sprinkler Pipe PVC Pipe
5 CASING Eliminator FRP
Quantity Pcs 6 Air Inlet Louver (Optional) FRP
Air Inlet Stand Hot Dip Galv. Steel
Ladder Assembly Hot Dip Galv. Steel
Stand Pipe PVC Pipe
6 WATER BASIN Horizontal Pipe N.A.
Quantity Pcs 3 Strainer SS 304
Infill Support Hot Dip Galv. Steel
Infill PVC Film
Bolt & Nuts Electroplated

7 AUX. SUCTION TANK 14 Noise Level (SPL) dBA 61.5

Flange Standard JIS 5kg/cm2 Note: The SPLs are measured 16m horizontally from the edge of the
tower at 1.5m above the foundation level.
Nov 2002 Ft125e.xls
 FT-150 STANDARD COUNTER FLOW TYPE COOLING TOWER SPECIFICATION

Manufacturer RYOWO (HOLDING) CO., LTD.

Type Counter Flow Cooling Tower
Origin China

1 OVERALL DIMENSION 8 DESIGN CONDITION

Diameter (Max.) mm 2900 Nominal Flow m3/hr 117
Height (Max.) mm 3110 Water Out Temp. 32°C
Height (w/o motor) mm 2790 Water In Temp. 37°C
Basin Dia. mm ø 2900 Ambient Wet Bulb Temp. 27°C
Net Weight kgs 580 Make-up Water Rate 1.43%
Operating Weight kgs 1680
9 SPRINKLER SYSTEM
2 MOTOR Sp Head Inlet (Dia) mm ø 150
Manufacturer Teco Tatung or Equivalent Sp Head Outlet (Dia x Qty) mm ø 65x6
Type TEFC
Volt/Phase/Hz 220/380/3/50Hz 10 AIR INLET MESH
Output Power 3HP 2.2kw Material PVC
Pole P 8 Quantity Pcs 12
Speed rpm 750
Insulation Class B 11 PIPING
Protection IP44 Elbow mm N.A.
Full Load Power Factor 72.5% Inlet (Dia.) mm ø 150
Full Load Power Efficiency 81.0% Outlet (Dia.) mm ø 150
Service Factor 1.15 Drain (Dia.) mm ø 50
Starting Current Amp 60/34.8 Overflow (Dia.) mm ø 50
Full Load Current Amp 10/5.8 Float Valve (Dia.) mm ø 20
Frame Size No. 132S Make-up Valve (Dia.) mm N.A.
Shaft Diameter mm ø 34 Float Ball (Dia.) mm ø 125

3 FAN 12 INFILL
Type Axial Thickness mm 0.2
Air Volume m3/hr 69000 Overall Diameter mm ø 2710
Speed rpm 750 Overall Height mm 680
Fan Diameter mm ø 1500
Bore Diameter mm ø 34 13 MATERIAL
No. of Blades Pcs 4 Fan Hub Al. Alloy
Fan Blade FRP
4 TRANSMISSION Motor Support Hot Dip Galv. Steel
Type Direct Fan Guard Hot Dip Galv. Steel
Gear Reducer Ratio N.A. Casing FRP
Motor Pulley N.A. Water Basin FRP
Fan Pulley N.A. Aux. Suction Tank FRP
Vee Belt N.A. Sprinkler Head Al. Alloy
Sprinkler Pipe PVC Pipe
5 CASING Eliminator FRP
Quantity Pcs 6 Air Inlet Louver (Optional) FRP
Air Inlet Stand Hot Dip Galv. Steel
Ladder Assembly Hot Dip Galv. Steel
Stand Pipe PVC Pipe
6 WATER BASIN Horizontal Pipe N.A.
Quantity Pcs 3 Strainer SS 304
Infill Support Hot Dip Galv. Steel
Infill PVC Film
Bolt & Nuts Electroplated

7 AUX. SUCTION TANK 14 Noise Level (SPL) dBA 62

Flange Standard JIS 5kg/cm2 Note: The SPLs are measured 16m horizontally from the edge of the
tower at 1.5m above the foundation level.
Nov 2002 Ft150e.xls
 FT-175 STANDARD COUNTER FLOW TYPE COOLING TOWER SPECIFICATION

Manufacturer RYOWO (HOLDING) CO., LTD.

Type Counter Flow Cooling Tower
Origin China

1 OVERALL DIMENSION 8 DESIGN CONDITION

Diameter (Max.) mm 3310 Nominal Flow m3/hr 136.8
Height (Max.) mm 3300 Water Out Temp. 32°C
Height (w/o motor) mm 2880 Water In Temp. 37°C
Basin Dia. mm ø 3310 Ambient Wet Bulb Temp. 27°C
Net Weight kgs 870 Make-up Water Rate 1.43%
Operating Weight kgs 2170
9 SPRINKLER SYSTEM
2 MOTOR Sp Head Inlet (Dia) mm ø 150
Manufacturer Teco Tatung or Equivalent Sp Head Outlet (Dia x Qty) mm ø 65x6
Type TEFC
Volt/Phase/Hz 220/380/3/50Hz 10 AIR INLET MESH
Output Power 5HP 3.7kw Material PVC
Pole P 10 Quantity Pcs 8
Speed rpm 600
Insulation Class B 11 PIPING
Protection IP44 Elbow mm N.A.
Full Load Power Factor 67.5% Inlet (Dia.) mm ø 150
Full Load Power Efficiency 81.0% Outlet (Dia.) mm ø 150
Service Factor 1.15 Drain (Dia.) mm ø 50
Starting Current Amp 107.4/62.4 Overflow (Dia.) mm ø 50
Full Load Current Amp 17.9/10.4 Float Valve (Dia.) mm ø 20 x 2
Frame Size No. 160M Make-up Valve (Dia.) mm N.A.
Shaft Diameter mm ø 38 Float Ball (Dia.) mm ø 125 x 2

3 FAN 12 INFILL
Type Axial Thickness mm 0.2
Air Volume m3/hr 72000 Overall Diameter mm ø 3100
Speed rpm 600 Overall Height mm 580
Fan Diameter mm ø 1800
Bore Diameter mm ø 38 13 MATERIAL
No. of Blades Pcs 4 Fan Hub Al. Alloy
Fan Blade Al. Alloy
4 TRANSMISSION Motor Support Hot Dip Galv. Steel
Type Direct Fan Guard Hot Dip Galv. Steel
Gear Reducer Ratio N.A. Casing FRP
Motor Pulley N.A. Water Basin FRP
Fan Pulley N.A. Aux. Suction Tank FRP
Vee Belt N.A. Sprinkler Head Al. Alloy
Sprinkler Pipe PVC Pipe
5 CASING Eliminator FRP
Quantity Pcs 8 Air Inlet Louver (Optional) FRP
Air Inlet Stand Hot Dip Galv. Steel
Ladder Assembly Hot Dip Galv. Steel
Stand Pipe PVC Pipe
6 WATER BASIN Horizontal Pipe N.A.
Quantity Pcs 4 Strainer SS 304
Infill Support Hot Dip Galv. Steel
Infill PVC Film
Bolt & Nuts Electroplated

7 AUX. SUCTION TANK 14 Noise Level (SPL) dBA 62

Flange Standard JIS 5kg/cm2 Note: The SPLs are measured 16m horizontally from the edge of the
tower at 1.5m above the foundation level.
Nov 2002 Ft175e.xls
 FT-200 STANDARD COUNTER FLOW TYPE COOLING TOWER SPECIFICATION

Manufacturer RYOWO (HOLDING) CO., LTD.

Type Counter Flow Cooling Tower
Origin China

1 OVERALL DIMENSION 8 DESIGN CONDITION

Diameter (Max.) mm 3310 Nominal Flow m3/hr 156
Height (Max.) mm 3450 Water Out Temp. 32°C
Height (w/o motor) mm 3030 Water In Temp. 37°C
Basin Dia. mm ø 3310 Ambient Wet Bulb Temp. 27°C
Net Weight kgs 900 Make-up Water Rate 1.43%
Operating Weight kgs 2200
9 SPRINKLER SYSTEM
2 MOTOR Sp Head Inlet (Dia) mm ø 150
Manufacturer Teco Tatung or Equivalent Sp Head Outlet (Dia x Qty) mm ø 65x6
Type TEFC
Volt/Phase/Hz 220/380/3/50Hz 10 AIR INLET MESH
Output Power 5HP 3.7kw Material PVC
Pole P 10 Quantity Pcs 8
Speed rpm 600
Insulation Class B 11 PIPING
Protection IP44 Elbow mm N.A.
Full Load Power Factor 67.5% Inlet (Dia.) mm ø 150
Full Load Power Efficiency 81.0% Outlet (Dia.) mm ø 150
Service Factor 1.15 Drain (Dia.) mm ø 50
Starting Current Amp 107.4/62.4 Overflow (Dia.) mm ø 50
Full Load Current Amp 17.9/10.4 Float Valve (Dia.) mm ø 20 x 2
Frame Size No. 160M Make-up Valve (Dia.) mm N.A.
Shaft Diameter mm ø 38 Float Ball (Dia.) mm ø 125 x 2

3 FAN 12 INFILL
Type Axial Thickness mm 0.2
Air Volume m3/hr 75000 Overall Diameter mm ø 3100
Speed rpm 600 Overall Height mm 680
Fan Diameter mm ø 1800
Bore Diameter mm ø 38 13 MATERIAL
No. of Blades Pcs 4 Fan Hub Al. Alloy
Fan Blade Al. Alloy
4 TRANSMISSION Motor Support Hot Dip Galv. Steel
Type Direct Fan Guard Hot Dip Galv. Steel
Gear Reducer Ratio N.A. Casing FRP
Motor Pulley N.A. Water Basin FRP
Fan Pulley N.A. Aux. Suction Tank FRP
Vee Belt N.A. Sprinkler Head Al. Alloy
Sprinkler Pipe PVC Pipe
5 CASING Eliminator FRP
Quantity Pcs 8 Air Inlet Louver (Optional) FRP
Air Inlet Stand Hot Dip Galv. Steel
Ladder Assembly Hot Dip Galv. Steel
Stand Pipe PVC Pipe
6 WATER BASIN Horizontal Pipe N.A.
Quantity Pcs 4 Strainer SS 304
Infill Support Hot Dip Galv. Steel
Infill PVC Film
Bolt & Nuts Electroplated

7 AUX. SUCTION TANK 14 Noise Level (SPL) dBA 62

Flange Standard JIS 5kg/cm2 Note: The SPLs are measured 16m horizontally from the edge of the
tower at 1.5m above the foundation level.
NOV 2002 Ft200e.xls
 FT-225 STANDARD COUNTER FLOW TYPE COOLING TOWER SPECIFICATION

Manufacturer RYOWO (HOLDING) CO., LTD.

Type Counter Flow Cooling Tower
Origin China

1 OVERALL DIMENSION 8 DESIGN CONDITION

Diameter (Max.) mm 3960 Nominal Flow m3/hr 175.8
Height (Max.) mm 3920 Water Out Temp. 32°C
Height (w/o motor) mm 3300 Water In Temp. 37°C
Basin Dia. mm ø 3920 Ambient Wet Bulb Temp. 27°C
Net Weight kgs 1300 Make-up Water Rate 1.43%
Operating Weight kgs 2700
9 SPRINKLER SYSTEM
2 MOTOR Sp Head Inlet (Dia) mm ø 200
Manufacturer Teco Tatung or Equivalent Sp Head Outlet (Dia x Qty) mm ø 80x6
Type TEFC
Volt/Phase/Hz 380/660/3/50Hz 10 AIR INLET MESH
Output Power 7.5HP 5.5kw Material PVC
Pole P 4 Quantity Pcs 8
Speed rpm 1450
Insulation Class B 11 PIPING
Protection IP44 Elbow mm N.A.
Full Load Power Factor 82.5% Inlet (Dia.) mm ø 200
Full Load Power Efficiency 86.0% Outlet (Dia.) mm ø 200
Service Factor 1.15 Drain (Dia.) mm ø 80
Starting Current Amp 124.38/72 Overflow (Dia.) mm ø 80
Full Load Current Amp 20.73/12 Float Valve (Dia.) mm ø 32
Frame Size No. 132S Make-up Valve (Dia.) mm N.A.
Shaft Diameter mm ø 32 Float Ball (Dia.) mm ø 250

3 FAN 12 INFILL
Type Axial Thickness mm 0.2
Air Volume m3/hr 96000 Overall Diameter mm ø 3760
Speed rpm 450 Overall Height mm 580
Fan Diameter mm ø 2400
Bore Diameter mm ø 50 13 MATERIAL
No. of Blades Pcs 4 Fan Hub Al. Alloy
Fan Blade Al. Alloy
4 TRANSMISSION Motor Support Hot Dip Galv. Steel
Type Vee Belt Fan Guard Hot Dip Galv. Steel
Gear Reducer Ratio N.A. Casing FRP
Motor Pulley 6" B3 Water Basin FRP
Fan Pulley 20" B3 Aux. Suction Tank FRP
Vee Belt B94" x 3 Sprinkler Head Al. Alloy
Sprinkler Pipe PVC Pipe
5 CASING Eliminator FRP
Quantity Pcs 12 Air Inlet Louver (Optional) FRP
Air Inlet Stand Hot Dip Galv. Steel
Ladder Assembly Hot Dip Galv. Steel
Stand Pipe PVC Pipe
6 WATER BASIN Horizontal Pipe N.A.
Quantity Pcs 6 Strainer SS 304
Infill Support Hot Dip Galv. Steel
Infill PVC Film
Bolt & Nuts Electroplated

7 AUX. SUCTION TANK 14 Noise Level (SPL) dBA 63

Flange Standard JIS 5kg/cm2 Note: The SPLs are measured 16m horizontally from the edge of the
tower at 1.5m above the foundation level.
Nov 2002 Ft225e.xls
 FT-250 STANDARD COUNTER FLOW TYPE COOLING TOWER SPECIFICATION

Manufacturer RYOWO (HOLDING) CO., LTD.

Type Counter Flow Cooling Tower
Origin China

1 OVERALL DIMENSION 8 DESIGN CONDITION

Diameter (Max.) mm 3960 Nominal Flow m3/hr 193.5
Height (Max.) mm 3920 Water Out Temp. 32°C
Height (w/o motor) mm 3300 Water In Temp. 37°C
Basin Dia. mm ø 3920 Ambient Wet Bulb Temp. 27°C
Net Weight kgs 1350 Make-up Water Rate 1.43%
Operating Weight kgs 2750
9 SPRINKLER SYSTEM
2 MOTOR Sp Head Inlet (Dia) mm ø 200
Manufacturer Teco Tatung or Equivalent Sp Head Outlet (Dia x Qty) mm ø 80x6
Type TEFC
Volt/Phase/Hz 380/660/3/50Hz 10 AIR INLET MESH
Output Power 7.5HP 5.5kw Material PVC
Pole P 4 Quantity Pcs 8
Speed rpm 1450
Insulation Class B 11 PIPING
Protection IP44 Elbow mm N.A.
Full Load Power Factor 82.5% Inlet (Dia.) mm ø 200
Full Load Power Efficiency 86.0% Outlet (Dia.) mm ø 200
Service Factor 1.15 Drain (Dia.) mm ø 80
Starting Current Amp 124.38/72 Overflow (Dia.) mm ø 80
Full Load Current Amp 20.73/12 Float Valve (Dia.) mm ø 32
Frame Size No. 132S Make-up Valve (Dia.) mm N.A.
Shaft Diameter mm ø 32 Float Ball (Dia.) mm ø 250

3 FAN 12 INFILL
Type Axial Thickness mm 0.2
Air Volume m3/hr 105000 Overall Diameter mm ø 3760
Speed rpm 450 Overall Height mm 680
Fan Diameter mm ø 2400
Bore Diameter mm ø 50 13 MATERIAL
No. of Blades Pcs 4 Fan Hub Al. Alloy
Fan Blade Al. Alloy
4 TRANSMISSION Motor Support Hot Dip Galv. Steel
Type Vee Belt Fan Guard Hot Dip Galv. Steel
Gear Reducer Ratio N.A. Casing FRP
Motor Pulley 6" B3 Water Basin FRP
Fan Pulley 20" B3 Aux. Suction Tank FRP
Vee Belt B94" x 3 Sprinkler Head Al Alloy
Sprinkler Pipe PVC Pipe
5 CASING Eliminator FRP
Quantity Pcs 12 Air Inlet Louver (Optional) FRP
Air Inlet Stand Hot Dip Galv. Steel
Ladder Assembly Hot Dip Galv. Steel
Stand Pipe PVC Pipe
6 WATER BASIN Horizontal Pipe N.A.
Quantity Pcs 6 Strainer SS 304
Infill Support Hot Dip Galv. Steel
Infill PVC Film
Bolt & Nuts Electroplated

7 AUX. SUCTION TANK 14 Noise Level (SPL) dBA 63

Flange Standard JIS 5kg/cm2 Note: The SPLs are measured 16m horizontally from the edge of the
tower at 1.5m above the foundation level.
Nov 2002 Ft250e.xls
 FT-300 STANDARD COUNTER FLOW TYPE COOLING TOWER SPECIFICATION

Manufacturer RYOWO (HOLDING) CO., LTD.

Type Counter Flow Cooling Tower
Origin China

1 OVERALL DIMENSION 8 DESIGN CONDITION

Diameter (Max.) mm 4360 Nominal Flow m3/hr 234
Height (Max.) mm 3990 Water Out Temp. 32°C
Height (w/o motor) mm 3290 Water In Temp. 37°C
Basin Dia. mm ø 4350 Ambient Wet Bulb Temp. 27°C
Net Weight kgs 1550 Make-up Water Rate 1.43%
Operating Weight kgs 3350
9 SPRINKLER SYSTEM
2 MOTOR Sp Head Inlet (Dia) mm ø 200
Manufacturer Teco Tatung or Equivalent Sp Head Outlet (Dia x Qty) mm ø 80x6
Type TEFC
Volt/Phase/Hz 380/660/3/50Hz 10 AIR INLET MESH
Output Power 10HP 7.5kw Material PVC
Pole P 4 Quantity Pcs 16
Speed rpm 1450
Insulation Class B 11 PIPING
Protection IP44 Elbow mm N.A.
Full Load Power Factor 85.5% Inlet (Dia.) mm ø 200
Full Load Power Efficiency 87.5% Outlet (Dia.) mm ø 200
Service Factor 1.15 Drain (Dia.) mm ø 80
Starting Current Amp 91.2/52.5 Overflow (Dia.) mm ø 80
Full Load Current Amp 15.2/8.75 Float Valve (Dia.) mm ø 32
Frame Size No. 132M Make-up Valve (Dia.) mm N.A.
Shaft Diameter mm ø 32 Float Ball (Dia.) mm ø 250

3 FAN 12 INFILL
Type Axial Thickness mm 0.2
Air Volume m3/hr 120000 Overall Diameter mm ø 4200
Speed rpm 450 Overall Height mm 680
Fan Diameter mm ø 2400
Bore Diameter mm ø 50 13 MATERIAL
No. of Blades Pcs 4 Fan Hub Al. Alloy
Fan Blade Al. Alloy
4 TRANSMISSION Motor Support Hot Dip Galv. Steel
Type Vee Belt Fan Guard Hot Dip Galv. Steel
Gear Reducer Ratio N.A. Casing FRP
Motor Pulley 6" B3 Water Basin FRP
Fan Pulley 20" B3 Aux. Suction Tank FRP
Vee Belt B94" x 3 Sprinkler Head Al. Alloy
Sprinkler Pipe PVC Pipe
5 CASING Eliminator FRP
Quantity Pcs 16 Air Inlet Louver (Optional) FRP
Air Inlet Stand Hot Dip Galv. Steel
Ladder Assembly Hot Dip Galv. Steel
Stand Pipe PVC Pipe
6 WATER BASIN Horizontal Pipe N.A.
Quantity Pcs 8 Strainer SS 304
Infill Support Hot Dip Galv. Steel
Infill PVC Film
Bolt & Nuts Electroplated

7 AUX. SUCTION TANK 14 Noise Level (SPL) dBA 64

Flange Standard JIS 5kg/cm2 Note: The SPLs are measured 16m horizontally from the edge of the
tower at 1.5m above the foundation level.
Nov 2002 Ft300e.xls
 FT-350 STANDARD COUNTER FLOW TYPE COOLING TOWER SPECIFICATION

Manufacturer RYOWO (HOLDING) CO., LTD.

Type Counter Flow Cooling Tower
Origin China

1 OVERALL DIMENSION 8 DESIGN CONDITION

Diameter (Max.) mm 4760 Nominal Flow m3/hr 273.42
Height (Max.) mm 4195 Water Out Temp. 32°C
Height (w/o motor) mm 3495 Water In Temp. 37°C
Basin Dia. mm ø 4760 Ambient Wet Bulb Temp. 27°C
Net Weight kgs 1720 Make-up Water Rate 1.43%
Operating Weight kgs 3720
9 SPRINKLER SYSTEM
2 MOTOR Sp Head Inlet (Dia) mm ø 200
Manufacturer Teco Tatung or Equivalent Sp Head Outlet (Dia x Qty) mm ø 80x6
Type TEFC
Volt/Phase/Hz 380/660/3/50Hz 10 AIR INLET MESH
Output Power 10HP 7.5kw Material PVC
Pole P 4 Quantity Pcs 16
Speed rpm 1450
Insulation Class B 11 PIPING
Protection IP44 Elbow mm N.A.
Full Load Power Factor 85.5% Inlet (Dia.) mm ø 200
Full Load Power Efficiency 87.5% Outlet (Dia.) mm ø 200
Service Factor 1.15 Drain (Dia.) mm ø 80
Starting Current Amp 91.2/52.5 Overflow (Dia.) mm ø 80
Full Load Current Amp 15.2/8.75 Float Valve (Dia.) mm ø 32
Frame Size No. 132M Make-up Valve (Dia.) mm N.A.
Shaft Diameter mm Ø 32 Float Ball (Dia.) mm ø 250

3 FAN 12 INFILL
Type Axial Thickness mm 0.2
Air Volume m3/hr 132000 Overall Diameter mm ø 4600
Speed rpm 450 Overall Height mm 580
Fan Diameter mm ø 2400
Bore Diameter mm ø 50 13 MATERIAL
No. of Blades Pcs 4 Fan Hub Al. Alloy
Fan Blade Al. Alloy
4 TRANSMISSION Motor Support Hot Dip Galv. Steel
Type Vee Belt Fan Guard Hot Dip Galv. Steel
Gear Reducer Ratio N.A. Casing FRP
Motor Pulley 6" B3 Water Basin FRP
Fan Pulley 20" B3 Aux. Suction Tank FRP
Vee Belt B94" x 3 Sprinkler Head Al. Alloy
Sprinkler Pipe PVC Pipe
5 CASING Eliminator FRP
Quantity Pcs 16 Air Inlet Louver (Optional) FRP
Air Inlet Stand Hot Dip Galv. Steel
Ladder Assembly Hot Dip Galv. Steel
Stand Pipe PVC Pipe
6 WATER BASIN Horizontal Pipe N.A.
Quantity Pcs 8 Strainer SS 304
Infill Support Hot Dip Galv. Steel
Infill PVC Film
Bolt & Nuts Electroplated

7 AUX. SUCTION TANK 14 Noise Level (SPL) dBA 64.5

Flange Standard JIS 5kg/cm2 Note: The SPLs are measured 16m horizontally from the edge of the
tower at 1.5m above the foundation level.
Nov 2002 Ft350e.xls
 FT-400 STANDARD COUNTER FLOW TYPE COOLING TOWER SPECIFICATION

Manufacturer RYOWO (HOLDING) CO., LTD.

Type Counter Flow Cooling Tower
Origin China

1 OVERALL DIMENSION 8 DESIGN CONDITION

Diameter (Max.) mm 4760 Nominal Flow m3/hr 312
Height (Max.) mm 4255 Water Out Temp. 32°C
Height (w/o motor) mm 3495 Water In Temp. 37°C
Basin Dia. mm ø 4760 Ambient Wet Bulb Temp. 27°C
Net Weight kgs 2050 Make-up Water Rate 1.43%
Operating Weight kgs 3950
9 SPRINKLER SYSTEM
2 MOTOR Sp Head Inlet (Dia) mm ø 200
Manufacturer Teco Tatung or Equivalent Sp Head Outlet (Dia x Qty) mm ø 80x6
Type TEFC
Volt/Phase/Hz 380660/3/50Hz 10 AIR INLET MESH
Output Power 15HP 11kw Material PVC
Pole P 4 Quantity Pcs 16
Speed rpm 1450
Insulation Class B 11 PIPING
Protection IP44 Elbow mm N.A.
Full Load Power Factor 88.0% Inlet (Dia.) mm ø 200
Full Load Power Efficiency 89.5% Outlet (Dia.) mm ø 200
Service Factor 1.15 Drain (Dia.) mm ø 80
Starting Current Amp 129.6/74.4 Overflow (Dia.) mm ø 80
Full Load Current Amp 21.6/12.4 Float Valve (Dia.) mm ø 32
Frame Size No. 160M Make-up Valve (Dia.) mm N.A.
Shaft Diameter mm ø 42 Float Ball (Dia.) mm ø 250

3 FAN 12 INFILL
Type Axial Thickness mm 0.2
Air Volume m3/hr 147000 Overall Diameter mm ø 4600
Speed rpm 375 Overall Height mm 680
Fan Diameter mm ø 3000
Bore Diameter mm ø 50 13 MATERIAL
No. of Blades Pcs 4 Fan Hub Al. Alloy
Fan Blade Al. Alloy
4 TRANSMISSION Motor Support Hot Dip Galv. Steel
Type Vee Belt Fan Guard Hot Dip Galv. Steel
Gear Reducer Ratio N.A. Casing FRP
Motor Pulley 6" B4 Water Basin FRP
Fan Pulley 24" B4 Aux. Suction Tank FRP
Vee Belt B102" x 4 Sprinkler Head Al. Alloy
Sprinkler Pipe PVC Pipe
5 CASING Eliminator FRP
Quantity Pcs 16 Air Inlet Louver (Optional) FRP
Air Inlet Stand Hot Dip Galv. Steel
Ladder Assembly Hot Dip Galv. Steel
Stand Pipe PVC Pipe
6 WATER BASIN Horizontal Pipe N.A.
Quantity Pcs 8 Strainer SS 304
Infill Support Hot Dip Galv. Steel
Infill PVC Film
Bolt & Nuts Electroplated

7 AUX. SUCTION TANK 14 Noise Level (SPL) dBA 61.5

Flange Standard JIS 5kg/cm2 Note: The SPLs are measured 16m horizontally from the edge of the
tower at 1.5m above the foundation level.
Nov 2002 Ft400e.xls
 FT-500 STANDARD COUNTER FLOW TYPE COOLING TOWER SPECIFICATION

Manufacturer RYOWO (HOLDING) CO., LTD.

Type Counter Flow Cooling Tower
Origin China

1 OVERALL DIMENSION 8 DESIGN CONDITION

Diameter (Max.) mm 5600 Nominal Flow m3/hr 390.6
Height (Max.) mm 4590 Water Out Temp. 32°C
Height (w/o motor) mm 3830 Water In Temp. 37°C
Basin Dia. mm ø 5600 Ambient Wet Bulb Temp. 27°C
Net Weight kgs 2450 Make-up Water Rate 1.43%
Operating Weight kgs 6150
9 SPRINKLER SYSTEM
2 MOTOR Sp Head Inlet (Dia) mm ø 250
Manufacturer Teco Tatung or Equivalent Sp Head Outlet (Dia x Qty) mm ø 100x6
Type TEFC
Volt/Phase/Hz 380/660/3/50Hz 10 AIR INLET MESH
Output Power 15HP 11kw Material PVC
Pole P 4 Quantity Pcs 12
Speed rpm 1450
Insulation Class B 11 PIPING
Protection IP44 Elbow mm N.A.
Full Load Power Factor 88.0% Inlet (Dia.) mm ø 250
Full Load Power Efficiency 89.5% Outlet (Dia.) mm ø 250
Service Factor 1.15 Drain (Dia.) mm ø 100
Starting Current Amp 129.6/74.4 Overflow (Dia.) mm ø 100
Full Load Current Amp 21.6/12.4 Float Valve (Dia.) mm ø 50
Frame Size No. 160M Make-up Valve (Dia.) mm N.A.
Shaft Diameter mm ø 42 Float Ball (Dia.) mm ø 300

3 FAN 12 INFILL
Type Axial Thickness mm 0.2
Air Volume m3/hr 162000 Overall Diameter mm ø 5370
Speed rpm 375 Overall Height mm 680
Fan Diameter mm ø 3000
Bore Diameter mm ø 50 13 MATERIAL
No. of Blades Pcs 4 Fan Hub Al. Alloy
Fan Blade Al. Alloy
4 TRANSMISSION Motor Support Hot Dip Galv. Steel
Type Vee Belt Fan Guard Hot Dip Galv. Steel
Gear Reducer Ratio N.A. Casing FRP
Motor Pulley 6" B4 Water Basin FRP
Fan Pulley 24" B4 Aux. Suction Tank FRP
Vee Belt B102" x 4 Sprinkler Head Al. Alloy
Sprinkler Pipe PVC Pipe
5 CASING Eliminator FRP
Quantity Pcs 16 Air Inlet Louver (Optional) FRP
Air Inlet Stand Hot Dip Galv. Steel
Ladder Assembly Hot Dip Galv. Steel
Stand Pipe PVC Pipe
6 WATER BASIN Horizontal Pipe N.A.
Quantity Pcs 12 Strainer SS 304
Infill Support Hot Dip Galv. Steel
Infill PVC Film
Bolt & Nuts Electroplated

7 AUX. SUCTION TANK 14 Noise Level (SPL) dBA 62

Flange Standard JIS 5kg/cm2 Note: The SPLs are measured 16m horizontally from the edge of the
tower at 1.5m above the foundation level.
Nov 2002 Ft500e.xls
 FT-600 STANDARD COUNTER FLOW TYPE COOLING TOWER SPECIFICATION

Manufacturer RYOWO (HOLDING) CO., LTD.

Type Counter Flow Cooling Tower
Origin China

1 OVERALL DIMENSION 8 DESIGN CONDITION

Diameter (Max.) mm 6600 Nominal Flow m3/hr 468.6
Height (Max.) mm 5310 Water Out Temp. 32°C
Height (w/o motor) mm 4470 Water In Temp. 37°C
Basin Dia. mm ø 6600 Ambient Wet Bulb Temp. 27°C
Net Weight kgs 3950 Make-up Water Rate 1.43%
Operating Weight kgs 9350
9 SPRINKLER SYSTEM
2 MOTOR Sp Head Inlet (Dia) mm ø 250
Manufacturer Teco Tatung or Equivalent Sp Head Outlet (Dia x Qty) mm ø 80x8
Type TEFC
Volt/Phase/Hz 380/660/3/50Hz 10 AIR INLET MESH
Output Power 20HP 15kw Material PVC
Pole P 4 Quantity Pcs 16
Speed rpm 1450
Insulation Class B 11 PIPING
Protection IP44 Elbow mm N.A.
Full Load Power Factor 88.5% Inlet (Dia.) mm ø 250
Full Load Power Efficiency 90.5% Outlet (Dia.) mm ø 250
Service Factor 1.15 Drain (Dia.) mm ø 100
Starting Current Amp 169.8/97.2 Overflow (Dia.) mm ø 100
Full Load Current Amp 28.3/16.2 Float Valve (Dia.) mm ø 50
Frame Size No. 160L Make-up Valve (Dia.) mm N.A.
Shaft Diameter mm ø 28 Float Ball (Dia.) mm ø 300

3 FAN 12 INFILL
Type Axial Thickness mm 0.2
Air Volume m3/hr 210000 Overall Diameter mm ø 6210
Speed rpm 314 Overall Height mm 580
Fan Diameter mm ø 3400
Bore Diameter mm ø 60 13 MATERIAL
No. of Blades Pcs 4 Fan Hub Hot Dip Galv. Steel
Fan Blade FRP
4 TRANSMISSION Motor Support Hot Dip Galv. Steel
Type Gear Reducer Fan Guard Hot Dip Galv. Steel
Gear Reducer Ratio CB5 (4.68:1) Casing FRP
Motor Pulley N.A. Water Basin FRP
Fan Pulley N.A. Aux. Suction Tank FRP
Vee Belt N.A. Sprinkler Head Al. Alloy
Sprinkler Pipe PVC Pipe
5 CASING Eliminator FRP
Quantity Pcs 16 Air Inlet Louver (Optional) FRP
Air Inlet Stand Hot Dip Galv. Steel
Ladder Assembly Hot Dip Galv. Steel
Stand Pipe PVC Pipe
6 WATER BASIN Horizontal Pipe N.A.
Quantity Pcs 16 Strainer SS 304
Infill Support Hot Dip Galv. Steel
Infill PVC Film
Bolt & Nuts Electroplated

7 AUX. SUCTION TANK 14 Noise Level (SPL) dBA 65

Flange Standard JIS 5kg/cm2 Note: The SPLs are measured 16m horizontally from the edge of the
tower at 1.5m above the foundation level.
Nov 2002 Ft600e.xls
 FT-700 STANDARD COUNTER FLOW TYPE COOLING TOWER SPECIFICATION

Manufacturer RYOWO (HOLDING) CO., LTD.

Type Counter Flow Cooling Tower
Origin China

1 OVERALL DIMENSION 8 DESIGN CONDITION

Diameter (Max.) mm 6600 Nominal Flow m3/hr 546.6
Height (Max.) mm 5510 Water Out Temp. 32°C
Height (w/o motor) mm 4670 Water In Temp. 37°C
Basin Dia. mm ø 6600 Ambient Wet Bulb Temp. 27°C
Net Weight kgs 4050 Make-up Water Rate 1.43%
Operating Weight kgs 9450
9 SPRINKLER SYSTEM
2 MOTOR Sp Head Inlet (Dia) mm ø 250
Manufacturer Teco Tatung or Equivalent Sp Head Outlet (Dia x Qty) mm ø 80x8
Type TEFC
Volt/Phase/Hz 380/660/3/50Hz 10 AIR INLET MESH
Output Power 20HP 15kw Material PVC
Pole P 4 Quantity Pcs 16
Speed rpm 1450
Insulation Class B 11 PIPING
Protection IP44 Elbow mm N.A.
Full Load Power Factor 88.5% Inlet (Dia.) mm ø 250
Full Load Power Efficiency 90.5% Outlet (Dia.) mm ø 250
Service Factor 1.15 Drain (Dia.) mm ø 100
Starting Current Amp 169.8/97.2 Overflow (Dia.) mm ø 100
Full Load Current Amp 28.3/16.2 Float Valve (Dia.) mm ø 50
Frame Size No. 160L Make-up Valve (Dia.) mm N.A.
Shaft Diameter mm ø 28 Float Ball (Dia.) mm ø 300

3 FAN 12 INFILL
Type Axial Thickness mm 0.2
Air Volume m3/hr 225000 Overall Diameter mm ø 6210
Speed rpm 314 Overall Height mm 680
Fan Diameter mm ø 3400
Bore Diameter mm ø 60 13 MATERIAL
No. of Blades Pcs 4 Fan Hub Hot Dip Galv. Steel
Fan Blade FRP
4 TRANSMISSION Motor Support Hot Dip Galv. Steel
Type Gear Reducer Fan Guard Hot Dip Galv. Steel
Gear Reducer Ratio CB5 (4.68:1) Casing FRP
Motor Pulley N.A. Water Basin FRP
Fan Pulley N.A. Aux. Suction Tank FRP
Vee Belt N.A. Sprinkler Head Al. Alloy
Sprinkler Pipe PVC Pipe
5 CASING Eliminator FRP
Quantity Pcs 16 Air Inlet Louver (Optional) FRP
Air Inlet Stand Hot Dip Galv. Steel
Ladder Assembly Hot Dip Galv. Steel
Stand Pipe PVC Pipe
6 WATER BASIN Horizontal Pipe N.A.
Quantity Pcs 16 Strainer SS 304
Infill Support Hot Dip Galv. Steel
Infill PVC Film
Bolt & Nuts Electroplated

7 AUX. SUCTION TANK 14 Noise Level (SPL) dBA 66

Flange Standard JIS 5kg/cm2 Note: The SPLs are measured 16m horizontally from the edge of the
tower at 1.5m above the foundation level.
Nov 2002 Ft700e.xls
 FT-800 STANDARD COUNTER FLOW TYPE COOLING TOWER SPECIFICATION

Manufacturer RYOWO (HOLDING) CO., LTD.

Type Counter Flow Cooling Tower
Origin China

1 OVERALL DIMENSION 8 DESIGN CONDITION

Diameter (Max.) mm 7600 Nominal Flow m3/hr 625.2
Height (Max.) mm 5660 Water Out Temp. 32°C
Height (w/o motor) mm 4720 Water In Temp. 37°C
Basin Dia. mm ø 7600 Ambient Wet Bulb Temp. 27°C
Net Weight kgs 4700 Make-up Water Rate 1.43%
Operating Weight kgs 11900
9 SPRINKLER SYSTEM
2 MOTOR Sp Head Inlet (Dia) mm ø 300
Manufacturer Teco Tatung or Equivalent Sp Head Outlet (Dia x Qty) mm ø 100x10
Type TEFC
Volt/Phase/Hz 380/660/3/50Hz 10 AIR INLET MESH
Output Power 30HP 22kw Material PVC
Pole P 4 Quantity Pcs 16
Speed rpm 1450
Insulation Class B 11 PIPING
Protection IP44 Elbow mm N.A.
Full Load Power Factor 85.5% Inlet (Dia.) mm ø 300
Full Load Power Efficiency 90.5% Outlet (Dia.) mm ø 300
Service Factor 1.15 Drain (Dia.) mm ø 100
Starting Current Amp 264 /154 Overflow (Dia.) mm ø 100
Full Load Current Amp 43.9/25.7 Float Valve (Dia.) mm ø 32x2
Frame Size No. 180M Make-up Valve (Dia.) mm N.A.
Shaft Diameter mm ø 32 Float Ball (Dia.) mm ø 250x2

3 FAN 12 INFILL
Type Axial Thickness mm 0.2
Air Volume m3/hr 300000 Overall Diameter mm ø 7210
Speed rpm 314 Overall Height mm 580
Fan Diameter mm ø 3700
Bore Diameter mm ø 70 13 MATERIAL
No. of Blades Pcs 4 Fan Hub Hot Dip Galv. Steel
Fan Blade FRP
4 TRANSMISSION Motor Support Hot Dip Galv. Steel
Type Gear Reducer Fan Guard Hot Dip Galv. Steel
Gear Reducer Ratio CB7 (4.68:1) Casing FRP
Motor Pulley N.A. Water Basin FRP
Fan Pulley N.A. Aux. Suction Tank FRP
Vee Belt N.A. Sprinkler Head Al. Alloy
Sprinkler Pipe PVC Pipe
5 CASING Eliminator FRP
Quantity Pcs 16 Air Inlet Louver (Optional) FRP
Air Inlet Stand Hot Dip Galv. Steel
Ladder Assembly Hot Dip Galv. Steel
Stand Pipe PVC Pipe
6 WATER BASIN Horizontal Pipe N.A.
Quantity Pcs 16 Strainer SS 304
Infill Support Hot Dip Galv. Steel
Infill PVC Film
Bolt & Nuts Electroplated

7 AUX. SUCTION TANK 14 Noise Level (SPL) dBA 73

Flange Standard JIS 5kg/cm2 Note: The SPLs are measured 16m horizontally from the edge of the
tower at 1.5m above the foundation level.
Nov 2002 Ft800e.xls
 FT-1000 STANDARD COUNTER FLOW TYPE COOLING TOWER SPECIFICATION

Manufacturer RYOWO (HOLDING) CO., LTD.

Type Counter Flow Cooling Tower
Origin China

1 OVERALL DIMENSION 8 DESIGN CONDITION

Diameter (Max.) mm 7600 Nominal Flow m3/hr 780
Height (Max.) mm 5860 Water Out Temp. 32°C
Height (w/o motor) mm 4940 Water In Temp. 37°C
Basin Dia. mm ø 7600 Ambient Wet Bulb Temp. 27°C
Net Weight kgs 4900 Make-up Water Rate 1.43%
Operating Weight kgs 12100
9 SPRINKLER SYSTEM
2 MOTOR Sp Head Inlet (Dia) mm ø 300
Manufacturer Teco Tatung or Equivalent Sp Head Outlet (Dia x Qty) mm ø 100x10
Type TEFC
Volt/Phase/Hz 380/660/3/50Hz 10 AIR INLET MESH
Output Power 30HP 22kw Material PVC
Pole P 4 Quantity Pcs 16
Speed rpm 1450
Insulation Class B 11 PIPING
Protection IP44 Elbow mm N.A.
Full Load Power Factor 85.5% Inlet (Dia.) mm ø 300
Full Load Power Efficiency 90.5% Outlet (Dia.) mm ø 300
Service Factor 1.15 Drain (Dia.) mm ø 100
Starting Current Amp 264/154 Overflow (Dia.) mm ø 100
Full Load Current Amp 43.9/25.7 Float Valve (Dia.) mm ø 32x2
Frame Size No. 180M Make-up Valve (Dia.) mm N.A.
Shaft Diameter mm ø 32 Float Ball (Dia.) mm ø 250x2

3 FAN 12 INFILL
Type Axial Thickness mm 0.2
Air Volume m3/hr 324000 Overall Diameter mm ø 7210
Speed rpm 314 Overall Height mm 680
Fan Diameter mm ø 3700
Bore Diameter mm ø 70 13 MATERIAL
No. of Blades Pcs 4 Fan Hub Hot Dip Galv. Steel
Fan Blade FRP
4 TRANSMISSION Motor Support Hot Dip Galv. Steel
Type Gear Reducer Fan Guard Hot Dip Galv. Steel
Gear Reducer Ratio CB7 (4.68:1) Casing FRP
Motor Pulley N.A. Water Basin FRP
Fan Pulley N.A. Aux. Suction Tank FRP
Vee Belt N.A. Sprinkler Head Al. Alloy
Sprinkler Pipe PVC Pipe
5 CASING Eliminator FRP
Quantity Pcs 16 Air Inlet Louver (Optional) FRP
Air Inlet Stand Hot Dip Galv. Steel
Ladder Assembly Hot Dip Galv. Steel
Stand Pipe PVC Pipe
6 WATER BASIN Horizontal Pipe N.A.
Quantity Pcs 16 Strainer SS 304
Infill Support Hot Dip Galv. Steel
Infill PVC Film
Bolt & Nuts Electroplated

7 AUX. SUCTION TANK 14 Noise Level (SPL) dBA 74

Flange Standard JIS 5kg/cm2 Note: The SPLs are measured 16m horizontally from the edge of the
tower at 1.5m above the foundation level.
Nov 2002 Ft990e.xls