electrical-engineering-portal.com http://electrical-engineering-portal.

com/types-of-neutral-earthing-in-power-distribution-part-2

Types of neutral earthing in power distribution (part 2)

Low voltage switchgear - Power distribution (by MEC Electrical Engineering)

Continued from Types of neutral earthing in power distribution (part 1)

3. Resistance earthed systems

Resistance grounding has been used in three-phase industrial applications for many years and it resolves many of the
problems associated with solidly grounded and ungrounded systems. Resistance Grounding Systems limits the phase-to-
ground fault currents.

The main reasons for limiting the phase to ground fault current by resistance grounding are:

1. To reduce burning and melting effects in faulted electrical equipment like switchgear, transformers, cables, and
rotating machines.
2. To reduce mechanical stresses in circuits/Equipments carrying fault currents.
3. To reduce electrical-shock hazards to personnel caused by stray ground fault.
4. To reduce the arc blast or flash hazard.
5. To reduce the momentary line-voltage dip.
6. To secure control of the transient over-voltages while at the same time.
7. To improve the detection of the earth fault in a power system.

Grounding Resistors are generally connected between ground and neutral of transformers, generators and grounding
transformers to limit maximum fault current as per Ohms Law to a value which will not damage the equipment in the
power system and allow sufficient flow of fault current to detect and operate Earth protective relays to clear the fault.
Although it is possible to limit fault currents with high resistance Neutral grounding Resistors, earth short circuit currents can
be extremely reduced.

1/7
As a result of this fact, protection devices may not sense the fault.

Therefore, it is the most common application to limit single phase fault currents with low resistance Neutral Grounding
Resistors to approximately rated current of transformer and / or generator.

In addition, limiting fault currents to predetermined maximum values permits the designer to selectively coordinate the
operation of protective devices, which minimizes system disruption and allows for quick location of the fault.

There are two categories of resistance grounding:

1. Low resistance Grounding

2. High resistance Grounding

Ground fault current flowing through either type of resistor when a single phase faults to ground will increase the phase-to-
ground voltage of the remaining two phases. As a result, conductor insulation and surge arrestor ratings must be
based on line-to-line voltage. This temporary increase in phase-to-ground voltage should also be considered when
selecting two and three pole breakers installed on resistance grounded low voltage systems.

The increase in phase-to-ground voltage associated with ground fault currents also precludes the connection of line-to-
neutral loads directly to the system. If line-to neutral loads (such as 277V lighting) are present, they must be served by a
solidly grounded system. This can be achieved with an isolation transformer that has a three-phase delta primary and a
three-phase, four-wire, wye secondary.

Neither of these grounding systems (low or high resistance) reduces arc-flash

hazards associated with phase-to-phase faults, but both systems significantly
reduce or essentially eliminate the arc-flash hazards associated with phase-
to-ground faults. Both types of grounding systems limit mechanical stresses
and reduce thermal damage to electrical equipment, circuits, and apparatus
carrying faulted current.

The difference between Low Resistance Grounding and High Resistance

Grounding is a matter of perception and, therefore, is not well defined.
Generally speaking high-resistance grounding refers to a system in which the
Resistor neutral earthing
NGR let-through current is less than 50 to 100 A. Low resistance grounding
indicates that NGR current would be above 100 A.

A better distinction between the two levels might be alarm only and tripping. An alarm-only system continues to operate with
a single ground fault on the system for an unspecified amount of time. In a tripping system a ground fault is automatically
removed by protective relaying and circuit interrupting devices. Alarm-only systems usually limit NGR current to 10 A or less.

Rating of The Neutral grounding resistor:

1. Voltage: Line-to-neutral voltage of the system to which it is connected.

2. Initial Current: The initial current which will flow through the resistor with rated voltage applied.
3. Time: The “on time” for which the resistor can operate without exceeding the allowable temperature rise.

Top

A. Low Resistance Grounded

Low Resistance Grounding is used for large electrical systems where there is a high investment in capital equipment or
prolonged loss of service of equipment has a significant economic impact and it is not commonly used in low voltage
systems because the limited ground fault current is too low to reliably operate breaker trip units or fuses. This makes system
selectivity hard to achieve. Moreover, low resistance grounded systems are not suitable for 4-wire loads and hence have not
been used in commercial market applications.

A resistor is connected from the system neutral point to ground and generally sized to permit only 200A to 1200 amps of
ground fault current to flow. Enough current must flow such that protective devices can detect the faulted circuit and trip it off-
line but not so much current as to create major damage at the fault point.

2/7
Since the grounding impedance is in the form of resistance, any transient over
voltages are quickly damped out and the whole transient overvoltage phenomena
is no longer applicable. Although theoretically possible to be applied in low voltage
systems (e.g. 480V),significant amount of the system voltage dropped across the
grounding resistor, there is not enough voltage across the arc forcing current to
flow, for the fault to be reliably detected.

For this reason low resistance grounding is not used for low voltage systems
(under 1000 volts line to-line).

Advantages

1. Limits phase-to-ground currents to 200-400A.

2. Reduces arcing current and, to some extent, limits arc-flash hazards
associated with phase-to-ground arcing current conditions only.
3. May limit the mechanical damage and thermal damage to shorted transformer
and rotating machinery windings. Low resistance grounded

Disadvantages:

1. Does not prevent operation of over current devices.

2. Does not require a ground fault detection system.
3. May be utilized on medium or high voltage systems.
4. Conductor insulation and surge arrestors must be rated based on the line to-line voltage. Phase-to-neutral loads must
be served through an isolation transformer.
5. Used: Up to 400 amps for 10 sec are commonly found on medium voltage systems.

B. High Resistance Grounded

High resistance grounding is almost identical to low resistance grounding except that the ground fault current magnitude is
typically limited to 10 amperes or less. High resistance grounding accomplishes two things.

The first is that the ground fault current magnitude is sufficiently low enough such that no appreciable damage is done
at the fault point. This means that the faulted circuit need not be tripped off-line when the fault first occurs. Means that once
a fault does occur, we do not know where the fault is located. In this respect, it performs just like an ungrounded system.

The second point is it can control the transient overvoltage phenomenon present on ungrounded systems if engineered
properly.

Under earth fault conditions, the resistance must dominate over the system charging capacitance but not to the point of
permitting excessive current to flow and thereby excluding continuous operation.

High Resistance Grounding (HRG) systems limit the fault current when one
phase of the system shorts or arcs to ground, but at lower levels than low
resistance systems.

In the event that a ground fault condition exists, the HRG typically limits the
current to 5-10A.

HRG’s are continuous current rated, so the description of a particular unit

does not include a time rating. Unlike NGR’s, ground fault current flowing
through a HRG is usually not of significant magnitude to result in the
operation of an over current device. Since the ground fault current is not High resistance grounded

interrupted, a ground fault detection system must be installed.

3/7
These systems include a bypass contactor tapped across a portion of the resistor that pulses (periodically opens and
closes). When the contactor is open, ground fault current flows through the entire resistor. When the contactor is closed a
portion of the resistor is bypassed resulting in slightly lower resistance and slightly higher ground fault current.

To avoid transient over-voltages, an HRG resistor must be sized so that the amount of ground fault current the unit
will allow to flow exceeds the electrical system’s charging current. As a rule of thumb, charging current is estimated at 1A per
2000KVA of system capacity for low voltage systems and 2A per 2000KVA of system capacity at 4.16kV.

These estimated charging currents increase if surge suppressors are present. Each set of suppressors installed on a low
voltage system results in approximately 0.5A of additional charging current and each set of suppressors installed on a
4.16kV system adds 1.5A of additional charging current.

A system with 3000KVA of capacity at 480 volts would have an estimated charging current of 1.5A.Add one set of surge
suppressors and the total charging current increases by 0.5A to 2.0A. A standard 5A resistor could be used on this system.
Most resistor manufacturers publish detailed estimation tables that can be used to more closely estimate an electrical
system’s charging current.

Advantages

1. Enables high impedance fault detection in systems with weak capacitive connection to earth
2. Some phase-to-earth faults are self-cleared.
3. The neutral point resistance can be chosen to limit the possible over voltage transients to 2.5 times the fundamental
frequency maximum voltage.
4. Limits phase-to-ground currents to 5-10A.
5. Reduces arcing current and essentially eliminates arc-flash hazards associated with phase-to-ground arcing current
conditions only.
6. Will eliminate the mechanical damage and may limit thermal damage to shorted transformer and rotating machinery
windings.
7. Prevents operation of over current devices until the fault can be located (when only one phase faults to ground).
8. May be utilized on low voltage systems or medium voltage systems up to 5kV. IEEE Standard 141-1993 states that
“high resistance grounding should be restricted to 5kV class or lower systems with charging currents of about 5.5A or
less and should not be attempted on 15kV systems, unless proper grounding relaying is employed”.
9. Conductor insulation and surge arrestors must be rated based on the line to-line voltage. Phase-to-neutral loads must
be served through an isolation transformer.

Disadvantages

1. Generates extensive earth fault currents when combined with strong or moderate capacitive connection to earth Cost
involved.
2. Requires a ground fault detection system to notify the facility engineer that a ground fault condition has occurred.

Top

4. Resonant earthed system

Adding inductive reactance from the system neutral point to ground is an easy method of limiting the available ground fault
from something near the maximum 3 phase short circuit capacity (thousands of amperes) to a relatively low value (200 to
800 amperes).

To limit the reactive part of the earth fault current in a power system a neutral point reactor can be connected between the
transformer neutral and the station earthing system.

A system in which at least one of the neutrals is connected to earth through an

1. Inductive reactance.
2. Petersen coil / Arc Suppression Coil / Earth Fault Neutralizer.

4/7
The current generated by the reactance during an earth fault approximately compensates the capacitive component of the
single phase earth fault current, is called a resonant earthed system.

The system is hardly ever exactly tuned, i.e. the reactive current does not exactly equal the capacitive earth fault current of
the system.

A system in which the inductive current is slightly larger than the capacitive earth fault current is over compensated. A
system in which the induced earth fault current is slightly smaller than the capacitive earth fault current is under
compensated.

However, experience indicated that this inductive reactance to ground resonates

with the system shunt capacitance to ground under arcing ground fault conditions
and creates very high transient over voltages on the system. To control the transient
over voltages, the design must permit at least 60% of the 3 phase short circuit
current to flow underground fault conditions.

Example – A 6000 amp grounding reactor for a system having 10,000 amps 3
phase short circuit capacity available. Due to the high magnitude of ground fault
current required to control transient over voltages, inductance grounding is rarely
Resonant neutral earthing
used within industry.

Petersen Coils

A Petersen Coil is connected between the neutral point of the system and earth, and is rated so that the capacitive current in
the earth fault is compensated by an inductive current passed by the Petersen Coil. A small residual current will
remain, but this is so small that any arc between the faulted phase and earth will not be maintained and the fault will
extinguish. Minor earth faults such as a broken pin insulator, could be held on the system without the supply being
interrupted. Transient faults would not result in supply interruptions.

Although the standard ‘Peterson coil’ does not compensate the entire earth fault current in a network due to the presence of
resistive losses in the lines and coil, it is now possible to apply ‘residual current compensation’ by injecting an additional
180° out of phase current into the neutral via the Peterson coil. The fault current is thereby reduced to practically zero. Such
systems are known as ‘Resonant earthing with residual compensation’, and can be considered as a special case of reactive
earthing.

Resonant earthing can reduce EPR to a safe level. This is because the Petersen coil can often effectively act as a high
impedance NER, which will substantially reduce any earth fault currents, and hence also any corresponding EPR hazards
(e.g. touch voltages, step voltages and transferred voltages, including any EPR hazards impressed onto nearby
telecommunication networks).

Advantages

1. Small reactive earth fault current independent of the phase to earth capacitance of the system.
2. Enables high impedance fault detection.

Disadvantages

1. Risk of extensive active earth fault losses.

2. High costs associated.

Top

5. Earthing Transformers
For cases where there is no neutral point available for Neutral Earthing (e.g. for a delta winding), an earthing transformer
may be used to provide a return path for single phase fault currents.

5/7
 Earthing transformers

In such cases the impedance of the earthing transformer may be sufficient to act as effective earthing impedance. Additional
impedance can be added in series if required. A special ‘zig-zag’ transformer is sometimes used for earthing delta windings
to provide a low zero-sequence impedance and high positive and negative sequence impedance to fault currents.

Top

Conclusion
Resistance Grounding Systems have many advantages over solidly grounded systems including arc-flash hazard reduction,
limiting mechanical and thermal damage associated with faults, and controlling transient over voltages.

High resistance grounding systems may also be employed to maintain service continuity and assist with locating the source
of a fault.

When designing a system with resistors, the design/consulting engineer must consider the specific requirements for
conductor insulation ratings, surge arrestor ratings, breaker single-pole duty ratings, and method of serving phase-to-neutral
loads.

Comparison of Neutral Earthing System

Condition Un grounded Solid Low Resistance High Resistance Reactance

Grounded Grounded Grounded Grounding

Immunity to Worse Good Good Best Best

Transient Over
voltages

73% Increase in Poor Best Good Poor

Voltage Stress Under
Line-to-Ground Fault
Condition

Equipment Protected Worse Poor Better Best Best

Safety to Personnel Worse Better Good Best Best

Service Reliability Worse Good Better Best Best

Maintenance Cost Worse Good Better Best Best

Ease of Locating Worse Good Better Best Best

First Ground Fault

6/7
Permits Designer to Not Possible Good Better Best Best
CoordinateProtective
Devices

Reduction in Worse Better Good Best Best

Frequency of Faults

Lighting Arrestor Ungroundedneutral Grounded- Ungroundedneutral Ungroundedneutral Ungroundedneutral

type neutraltype type type type

Current for phase-to Less than 1% Varies, 5 to 20% Less than 1% 5 to 25%
ground fault in may be
percent ofthree- 100% or
phase fault current greater

Reference:

By Michael D. Seal, P.E., GE Senior Specification Engineer.

IEEE Standard 141-1993, “Recommended Practice for Electrical Power Distribution for Industrial Plants”
Don Selkirk, P.Eng, Saskatoon, Saskatchewan Canada

7/7