Scribd Logo
Upload

Welcome to Scribd!

  • 94 views

    Hook Check

    Uploaded by

    waweng22
    The document provides parameters and calculations for designing a hook section made of aluminum. It defines geometric properties of the hook like width, height, section modulus. It also defines forces acting on the hook like vertical shear, horizontal shear, moment due to eccentricity. Design checks are performed for bending, tension, combined tension and bending, and shear. All capacity/demand ratios are found to be less than 1, indicating the hook section is adequate.

    Copyright:

    © All Rights Reserved
    Download as PDF, TXT or read online from Scribd

    Hook Check

    Uploaded by

    waweng22
    94 views2 pages
    The document provides parameters and calculations for designing a hook section made of aluminum. It defines geometric properties of the hook like width, height, section modulus. It also defines forces acting on the hook like vertical shear, horizontal shear, moment due to eccentricity. Design checks are performed for bending, tension, combined tension and bending, and shear. All capacity/demand ratios are found to be less than 1, indicating the hook section is adequate.

    Original Title

    HOOK_CHECK

    Copyright

    © © All Rights Reserved

    Available Formats

    PDF, TXT or read online from Scribd

    Did you find this document useful?

    Is this content inappropriate?

    The document provides parameters and calculations for designing a hook section made of aluminum. It defines geometric properties of the hook like width, height, section modulus. It also defines forces acting on the hook like vertical shear, horizontal shear, moment due to eccentricity. Design checks are performed for bending, tension, combined tension and bending, and shear. All capacity/demand ratios are found to be less than 1, indicating the hook section is adequate.

    Copyright:

    © All Rights Reserved
    Download as PDF, TXT or read online from Scribd
    Download as pdf or txt
    94 views2 pages

    Hook Check

    Uploaded by

    waweng22
    The document provides parameters and calculations for designing a hook section made of aluminum. It defines geometric properties of the hook like width, height, section modulus. It also defines forces acting on the hook like vertical shear, horizontal shear, moment due to eccentricity. Design checks are performed for bending, tension, combined tension and bending, and shear. All capacity/demand ratios are found to be less than 1, indicating the hook section is adequate.

    Copyright:

    © All Rights Reserved
    Download as PDF, TXT or read online from Scribd
    Download as pdf or txt
    You are on page 1of 2

    HOOK PARAMETERS

    fo  250MPa Yield strength of aluminum

    γM1  1.25 Partial Safety factor

    Bh  29mm Width of the hook section

    Hh  15mm Height of the hook section

    2
    Bh  Hh 3
    Sx   1087.5mm
     Section modulus of the hook
    6
    2
    Ae  Bh  Hh  435 mm Gross sectional area

    FORCES ON THE HOOK

    Fy  4.96kN Vertical shear

    Fz  2.1kN Horizontal shear / Tension

    e  24mm Eccentricity of Fz

    M y  Fy  e  0.119  kN m

    DESIGN FORCES
    VEd  Fy

    NEd  Fz

    M EdY  M y
    CHECK FOR THE CAPACITY

    BENDING CHECK

    Sx
    M RdY  fo   0.217  kN m Moment capacity at the section
    γM1

    M EdY
    RM1   0.547
    M RdY Result1  "RM1 < 1; Therefore OK"

    TENSION CHECK

    Ae
    NRd  fo   87 kN
    γM1

    NEd
    RM2   0.024
    NRd Result2  "RM2 < 1; Therefore OK"

    COMBINED TENSION AND BENDING

    0.6
     M 1.7
     EdY  
    NEd
    RM3       0.565
    NRd  M RdY Result3  "RM3 < 1; Therefore OK"
      

    SHEAR CHECK
    ηv  0.8
    Factor for area of solid bar
    2
    Av  ηv  Ae  348  mm Shear area

    fo
    VRd  Av   40.184 kN Design shear resistance
    3  γM1

    VEd
    RM4   0.123
    VRd Result4  "RM4 < 1; Therefore OK"

    You might also like