FCL/FCLS Flexible Flanged Shaft Coupling

Selection CAD
Tool Download

●● The most popular flexible shaft coupling in Japan ●● Product

Standard ●● Alignmentadjustment
FCL
that is compliant with JIS B 1452 - 1991 "Flexible The product standard of the flexible flanged shaft ① Although the flexible flanged shaft coupling permits
Flanged Shaft Couplings". couplings is compliant with JIS B 1452 - 1991 "Flexible misalignment and transmits torque, if the
●● Simple structure comprised of a flange and Flanged Shaft Couplings". misalignment exceeds the allowable value,
coupling bolts. Easy-to-mount. vibration may occur or the life may be rapidly
●● Allowable value of the run-out of the joint outer
●● Bushings can be replaced just by removing shortened. Be sure to perform alignment
diameter to the shaft hole center, and that of the
coupling bolts. This makes maintenance and adjustment.
joint surface near the outer diameter 0.03mm
service easy. FCLS
② Shaft center misalignment includes eccentricity
●● Allowance of the bolt hole pitch circle diameter (parallel error of both shaft centers), argument
●● While it absorbs misalignment such as eccentricity
and argument, it prevents noise by absorbing and the bushing insertion hole pitch circle (angle error of both shaft centers), and end-play
torsional vibration. It will not transmit thrust load, ●● Material/Finish
diameter, allowance of the pitch, and the run-out (shaft direction movement of the shaft). Adjust the
either. FCL FCLS tolerance to the shaft bore center Unit：mm shaft alignment so that it will not exceed the
Joint Pitch Circle Diameter and Pitch Circle Diameter allowable value listed in the Dimension/
●● Two types are available: Cast Iron FCL and FC200 or more S25C or more Pitch Circle Diameter
Main Unit Pitch Allowance Run-out Tolerance
Carbon Steel FCLS . Performance table in this catalog.
Equivalent to SS400 Equivalent to SS400 60 / 67 / 75 ±0.16 0.12
Nut ③ The allowable values of the misalignment listed in
●● Structure Trivalent Chromate Treatment Trivalent Chromate Treatment 85 / 100 / 115 / 132 / 145 ±0.20 0.14
Washer Spring Lock SWRH62 SWRH62 170 / 180 / 200 / 236 ±0.26 0.18 the Dimension/Performance table are for the case
Washers Trivalent Chromate Treatment Trivalent Chromate Treatment 260 / 300 / 355 / 450 / 530 ±0.32 0.22 where any one of eccentricity, argument, and end-
NBR NBR 600 / 580 / 670 ±0.40 0.28 play occurs independently. Mixing of two or more
Nut Bushing
B (12) -j1a1〔HS (JIS A)＝70〕 B (12) -j1a1〔HS (JIS A)＝70〕
misalignment causes each of the allowable values
Equivalent to SS400 Equivalent to SS400 ●● Dimensional allowance of each part of the joint
Washer Trivalent Chromate Treatment or Trivalent Chromate Treatment or to be reduced to half.
Unit：mm
Electroless Nickel Plating Electroless Nickel Plating
Bolt Joint Outside Diameter A - g7 ④ Misalignment may occur not only in assembling
Equivalent to SS400 Equivalent to SS400
Bolt Bolt Hole and Bolt a H7 g7 into the device but also due to vibration, thermal
Trivalent Chromate Treatment Trivalent Chromate Treatment
Washer Inside Diameter＊1 a - ＋0.4
　0 expansion, and shaft bearing abrasion during
Spring Washer
Bushing Inside Diameter, Washer Inside Diameter ＋0.4
e9 operation. Therefore, it is recommended to keep
　0
and Bolt Bushing Insertion Area Diameter a1
the misalignment one third of the allowable value
Bushing Insertion Hole M H8 -
　0 or less.
Bushing Outside Diameter p - －0.4

Bolt Bushing Insertion Area Length m - k12 ●● Eccentricity, Parallel Offset Misalignment
＊1：　For those with the standard dimensions of 8, it is ＋0.2
　0 .

δ
●● Each symbol is identical to that shown in the Dimension/
Performance table.

●● Performance of the Bushing

Characteristics item NBR (Nitrile rubber)
Machine oil Excellent
Bush Joint Main body ●● Argument, Angular Misalignment
Gasoline Excellent
Benzine Impossible α
Ketone Impossible
Alcohol Excellent
Weak acid Good
Acid resistance
Strong acid OK
Impact resilience Good
Abrasion resistance Excellent ●● End-Play

Aging Resistance Excellent

Tensile strength Excellent
Heat resistance
90℃
(max. operating temperature, regular use)
Cold resistance
-20℃
(min. operating temperature, regular use)
●● Full bore alteration service capability.● x

We modify for individual shaft requirement

that will allow you for immediate use.
Additional Setscrew at Shaft Hole / Keyway ➡ P.xxxx
Available / Add'l charge

▶ https://www.nbk1560.com ▶ https://www.nbk1560.com