Scribd Logo
Upload

Welcome to Scribd!

  • 80 views

    Scottoiler: Kawasaki ZZR 600: Scottoiler Esystem (The Electronic Scottoiler) Installation Guide

    Uploaded by

    jitmarine
    This document provides installation instructions for a Scottoiler eSystem on a Kawasaki ZZR 600 motorcycle. It describes how to mount the dispenser on the rear spindle, connect the delivery tubing, position the reservoir, attach the display bracket and wires, prime the pump by filling the reservoir and tubing, and set the flow rate once installed. Additional resources like an installation guide and technical support contact information are also referenced.

    Copyright:

    © All Rights Reserved
    Download as PDF, TXT or read online from Scribd

    Scottoiler: Kawasaki ZZR 600: Scottoiler Esystem (The Electronic Scottoiler) Installation Guide

    Uploaded by

    jitmarine
    80 views1 page
    This document provides installation instructions for a Scottoiler eSystem on a Kawasaki ZZR 600 motorcycle. It describes how to mount the dispenser on the rear spindle, connect the delivery tubing, position the reservoir, attach the display bracket and wires, prime the pump by filling the reservoir and tubing, and set the flow rate once installed. Additional resources like an installation guide and technical support contact information are also referenced.

    Original Title

    Kawasaki_ZZR 600_Scottoiler eSystem (the electronic Scottoiler) _English17-10-2014.pdf

    Copyright

    © © All Rights Reserved

    Available Formats

    PDF, TXT or read online from Scribd

    Did you find this document useful?

    Is this content inappropriate?

    This document provides installation instructions for a Scottoiler eSystem on a Kawasaki ZZR 600 motorcycle. It describes how to mount the dispenser on the rear spindle, connect the delivery tubing, position the reservoir, attach the display bracket and wires, prime the pump by filling the reservoir and tubing, and set the flow rate once installed. Additional resources like an installation guide and technical support contact information are also referenced.

    Copyright:

    © All Rights Reserved
    Download as PDF, TXT or read online from Scribd
    Download as pdf or txt
    80 views1 page

    Scottoiler: Kawasaki ZZR 600: Scottoiler Esystem (The Electronic Scottoiler) Installation Guide

    Uploaded by

    jitmarine
    This document provides installation instructions for a Scottoiler eSystem on a Kawasaki ZZR 600 motorcycle. It describes how to mount the dispenser on the rear spindle, connect the delivery tubing, position the reservoir, attach the display bracket and wires, prime the pump by filling the reservoir and tubing, and set the flow rate once installed. Additional resources like an installation guide and technical support contact information are also referenced.

    Copyright:

    © All Rights Reserved
    Download as PDF, TXT or read online from Scribd
    Download as pdf or txt
    of 1

    English-Kawasaki-ZZR 600-17th Octoder 2014 KAW-029

    Scottoiler: Kawasaki ZZR 600


    Scottoiler eSystem (the electronic Scottoiler) Installation Guide

    The delivery tubing can be routed along the swingarm


    using conduit and glue or self adhesive cable clips
    and the dispenser can be secured on the rear spindle
    using a Dispenser plate & Clip. For further information
    see our easy step installation guide - Dispenser
    Assemblies, General. The nib should feed the rear
    sprocket between the 6 & 7 o’clock positions, with the
    cut face outwards.
    Connect the delivery tubing to the check valve but do
    not connect the check valve, part 6, to the REP, part
    7, until you are priming the system.
    See picture below left

    The REP can be mounted under the seat, or behind


    the number plate. The REP can be orientated
    anywhere between horizontal and vertical, as long as
    the nozzle is inclined upwards. Remember to avoid
    exhaust and engine components and to keep the filling
    hole accessible. For further information, see our easy
    step installation guide – Reservoir Positions, General.

    Note: Picture shows a similar Swingarm

    The Display Bracket, part 5, can be rotated through


    360° to give 4 mounting options and can also be
    flipped to provide 4 further options. The bracket can
    be secured to any M5 / M6 bolt e.g. brake or clutch
    lever, brake cylinder or fairing mountings, in some
    cases you might need to trim the supplied bolt. It is
    possible to bend the bracket to shape, do so before
    fitting the Display Unit, part 1, to prevent damage to
    the unit. Alternatively, the Sticky Fastener, part 4, can
    be used to securely fasten the Display Unit to any flat
    surface e.g. the fork yokes.
    See third picture
    Note: This is a generic image

    Locate the bikes' battery and attach the red terminal


    from the display unit to the +ve terminal on the battery,
    and attach the black terminal to the -ve terminal of the
    battery. Take care when routing the wires, avoiding
    hot engine and exhaust components and also
    avoiding moving parts such as the throttle linkages.
    Where possible follow existing wiring and secure
    using cable ties.

    Once fitted, fill the REP and prime the pump. Attach
    the delivery tubing and prime until the oil reaches the
    Note: This is a generic image rear sprocket and then install the check valve. Do not
    install the check valve until the delivery tubing
    is full.

    For further information, see the website eSystem


    page which includes the Setup and Installation Guide.
    Set the flow rate, using the 'Driving Screen' on the
    Display Unit, to 60-70 seconds per drop (s/dp), check
    the condition of your chain after a ride, and adjust as
    required.
    See picture bottom left
    If you have any further comments or queries, and are unable to resolve them using our website, please do not hesitate to call
    technical on 0141 955 1100 or email [email protected] for assistance. Thank you.
    Scottoiler Ltd. 2 Riverside, Milngavie, Glasgow, G62 6PL Tel. 0141 955 1100 Fax. 0141 956 5896 www.scottoiler.com

    You might also like