Tutorial 1 - Conduction in Cartiesian System

Ramesh. K

February 21, 2012

Thermal Conductivity
1. The thermal conductivity of a sheet of rigid, extruded insulation is is reported to be k = 0.0029 mWo K . The
measured temperature difference across a 20mm thick sheet of material is 10o C.

(a) what is the heat flux through a 2m × 2m sheet of insulation.

2. if 3kW is conducted through a section of insulating material 0.6m2 in cross section and 2.5 cm thick and
the thermal conductivity may be taken as 0.2 mWo C , compute the temperature difference across the material.

3. The temperatures on the faces of a plane wall 15 cm thick are 375o C and 85o C. The wall is constructed
kg
of a special glass with the following properties: k = 0.78 mWo C , ρ = 2700 m kJ
3 , cp = 0.84 kg o C . What is the

heat flow through the wall at steady state conditions?

4. A certain thickness has a thermal conductivity of 10 mWo C . What is the thickness necessary to effect a
W
temperature of drop of 500o C for a heat flow of 400 m2.

5. A Truncated cone 30 cm is constructed of aluminium. The diameter of the top is 7.5cm, and the diameter
at the bottom is 12.5cm. The lower surface is maintained at 93o C; the upper surface at 5400 C. The outer
surface is insulated. Assuming one-dimensional heat flow, what is the rate of heat transfer in watts.

6. what is the thickness required by masonary wall having thermal conductivity of k = 0.75 mWo K , if the heat
rate is to be 80% of the heat rate through a composite structure wall having a thermal conductivity
k = 0.25 mWo K and thickness of 100mm? Both walls are subjected to same temperature difference.

7. The inner and outer surface temperatures of a glass window 5mm thick are 15o C and 5o C. What is the
heat loss through a window that is 1m × 3m on a side? The thermal conductivity of of glass is 1.4 mWo K

8. Find the heat flux and temperature distribution in an infinite slab of thickness ‘b‘ whose thermal conduc-
tivity varies linearly with the temperature in the form k = k0 (1 + cT ), where k0 and ‘c‘ are constants.
Sketch the temperature distribution when c > 0 and c < 0

9. The thermal conductivity of a plane wall varies as k = k0 (1 + bT + cT 2 ). If the wall thickness is L and
the surface temperature are maintained at T1 &T2 . Show
that the heat flux ‘q‘ through the wall is given
by q = ko (T 1−T
L
2)
1 + b
2
[T 1 + T 2] + c
3
[T1
2
+ T T
1 2 + T 2
2 .]

1
10. The temperature distribution across a wall of 1m thick at a certian instant of time is given as T (x) = a+bx+
o o
cx2 where T is in o C and x in m while a = 900 o C , b = −300 mC , c = −50 mC2 . A uniform heat generation,
W kg W
q̇ = 1000 m 2
3 , is present in the wall of area 10m , having the properties ρ = 600 m3 , k = 40
mK̇
, cp = 4 kgkJK̇

• Determine the rate of heat transfer that is entering the wall (x = 0) and leaving the wall(x = 1).
• Determine the rate of change of engergy storage in the wall.
• Determine the rate of temperature change at (x = 0.0, 0.25, 0.5, 0.75)

11. Assume steady-state, one-dimensional heat conduction through the symmetrical shape shown in Figure 1,
assuming that there is no internal heat generation, derive an expression for the thermal conductivity k(x)

Figure 1: Tapered Section

for these conditions

A(x) = (1 − x)
T (x) = 300(1 − 2x − x3 ), q = 6000W

where A in m2 , x in m and T in Kelvins

12. Consider a plane wall as shown in Figure 2 of 100mm thick and of thermal conductivity 100W
m.K
. Steady
00
state conditions are known to exist with T1 = 400K, T2 = 600K. Determine the heat flux q and the
temperature gradient dT
dx
for the coordinate system shown in below

Figure 2: Plane wall