RIBA - The Handbook of Sustainable Refurbishment PDF

PPC live area 246x189mm, Spine 17mm, bleed 18mm
‘An incisive book that provides practical strategies and tactics for sustainable refurbishment, literally from
The Handbook of Sustainable Refurbishment

the ground up. Richly illustrated with informative diagrams, supported by accessible quantitative analysis
and reinforced by detailed case study examples, this book is a triumph.’
Koen Steemers PhD RIBA/ARB, Professor of Sustainable Design and Head of the Department of
Architecture, University of Cambridge
‘Nick Baker tackles head on what many eminent scientists in Cambridge regard as most pressing
contemporary problems, the sustainable refurbishment of the existing building stock, much of which is
going to be with us still in 2050. Dr Baker delivers his profound understanding of these difficult issues in a
wholly intelligible and compelling way. I cannot commend this book to my profession and its patrons highly
The Handbook of
enough.’
Professor Alan Short, University of Cambridge and Short and Associates Architects
first and second image Stevenage Borough Council, third image Nick V. Baker
The refurbishment of existing buildings is a crucial yet often neglected subject within sustainable architecture
– attention is usually focused on new buildings. Many old buildings waste large amounts of energy and
Sustainable
provide poor internal conditions for occupants through poor lighting, poor ventilation, solar penetration and
glare, and poor control of heating and cooling. Demolition is an option but the refurbishment alternative is
increasingly seen as more sustainable in terms of architectural value, materials use, neighbourhood
disruption and waste disposal. In addition, the potential impact of low energy refurbishment is much greater
Refurbishment
than that for new build since there are many more buildings already in existence than will be built in the next
10–20 years, the period over which many CO2 targets apply.
The Handbook of Sustainable Refurbishment: Non-Domestic Buildings offers architects, engineers and a
wide range of building professionals practical advice, illustrated by real examples. It moves from principles of
sustainable refurbishment to specific design and engineering guidance for a variety of circumstances. It
emphasizes the need for an integrated approach by showing how refurbishment measures interact with one
and other, and with the occupants, and how performance is ultimately influenced by this interaction.
Nick V. Baker is an independent consultant and technical expert on the energy efficient refurbishment and
the development of LT software. He is affiliated to The Martin Centre, Department of Architecture, University
Non-Domestic Buildings
of Cambridge.
Nick V. Baker
Architecture/Engineering
www.earthscan.co.uk
Co-published with
Earthscan strives to minimize its impact on the environment Nick V. Baker

3456 EARTHSCAN Hndbk Sust Refurb:Layout 1 22/7/09 09:51 Page i
The Handbook of Sustainable Refurbishment

3456 EARTHSCAN Hndbk Sust Refurb:Layout 1 22/7/09 09:51 Page ii
3456 EARTHSCAN Hndbk Sust (RIBA):Layout 1 31/7/09 15:56 Page iii
The Handbook of
Sustainable Refurbishment
Non-Domestic Buildings
Nick V. Baker
Earthscan works with RIBA Publishing, part of the Royal Institute

of British Architects, to promote best practice and quality
professional guidance on sustainable architecture.
London • Sterling,VA
3456 EARTHSCAN Hndbk Sust Refurb:Layout 1 22/7/09 09:51 Page iv
First published by Earthscan in the UK and USA in 2009
Copyright © Nick V. Baker, 2009
All rights reserved
ISBN: 978-1-84407-486-0
Typeset by FiSH Books, London

Cover design by Yvonne Booth
Graphics by Mike J.V. Baker
For a full list of publications please contact:
Earthscan
Dunstan House
14a St Cross St
London, EC1N 8XA, UK
Tel: +44 (0)20 7841 1930
Fax: +44 (0)20 7242 1474
Email: [email protected]
Web: www.earthscan.co.uk
22883 Quicksilver Drive, Sterling,VA 20166-2012, USA
Earthscan publishes in association with the International Institute for Environment and Development
A catalogue record for this book is available from the British Library
Library of Congress Cataloging-in-Publication Data

Baker, Nick (Nick Vashon)
The handbook of sustainable refurbishment : non-domestic buildings / Nick V. Baker.
p. cm.
Includes bibliographical references and index.
ISBN 978-1-84407-486-0 (hardback)
1. Buildings–Repair and reconstruction. 2. Public buildings–Repair and reconstruction.
3. Commercial buildings–Remodeling. 4. Sustainable buildings–Design and construction. I.Title.
TH3401.B35 2009
690’.24–dc22
2009007564
At Earthscan we strive to minimize our environmental impacts and carbon footprint through reducing waste, recycling
and offsetting our CO2 emissions, including those created through publication of this book. For more details of our
environmental policy, see www.earthscan.co.uk.
This book was printed in Malta by Gutenberg Press.The paper used is FSC certified and the inks are vegetable based.
3456 EARTHSCAN Hndbk Sust Refurb:Layout 1 22/7/09 09:51 Page v
Contents
Preface..................................................................................................................xi
List of Acronyms and Abbreviations ..............................................................................xii
Part One Principles

1 Strategy for Low Emission Refurbishment ................................3
1.1 The case for low emission refurbishment: Energy use in buildings ..................3
1.2 Refurbishment versus rebuild: Economics and environmental impact .............3
1.3 The building, plant and occupants as a system ................................................4
1.4 Implications for change of use........................................................................5
Impact on energy consumption ................................................................6
1.5 Environmental comfort standards ...................................................................7
1.6 Passive environmental strategies......................................................................8
Natural ventilation....................................................................................9
Daylighting.............................................................................................10
1.7 Prioritizing refurbishment options ..............................................................13
Quantifying energy benefits....................................................................14
1.8 Integration with newbuild ..........................................................................18
1.9 Eco-communities and urban renewal .........................................................19
1.10 Environmental regulation.............................................................................20
Energy Performance of Buildings Directive.............................................20
Using other legislation in the UK ...........................................................22
Voluntary schemes and drivers ................................................................22
Part Two Practice

2 Floors .................................................................................27
2.1 Solid ground floors ......................................................................................27
Insulation options ..................................................................................27
Underfloor heating or cooling ................................................................27
2.2 Suspended ground floors..............................................................................28
Insulation options ...................................................................................28
Underfloor heating or cooling ................................................................28
3456 EARTHSCAN Hndbk Sust Refurb:Layout 1 22/7/09 09:51 Page vi
vi The Handbook of Sustainable Refurbishment
2.3 Intermediate floors ......................................................................................29

2.4 Thermal response implications of floor insulation.........................................29
3 Walls ..................................................................................31
3.1 Solid walls ...................................................................................................31
External insulation .................................................................................31
Implications for external insulation .........................................................32
Internal insulation...................................................................................33
Thermal response ...................................................................................33
Cold bridges...........................................................................................33
Interstitial condensation..........................................................................34
3.2 Cavity walls .................................................................................................35
Insulation options ...................................................................................35
Practical considerations...........................................................................36
Interstitial condensation..........................................................................36
Thermal implications..............................................................................37
Retrofit inner or outer leaf .....................................................................37
4 Roofs................................................................................................39
Roof types .............................................................................................39
4.1 Insulating roofs with attic spaces...................................................................40
Ventilation of attic space .........................................................................40
4.2 Insulating roofs with voids ...........................................................................40
4.3 Insulating solid roofs ....................................................................................41
Insulation above the waterproof membrane.............................................41
Insulation between waterproof membrane and structural deck ................42
Insulation below the structural deck........................................................43
4.4 Other thermal issues ....................................................................................43
Surface reflectance ..................................................................................43
Low-emissivity membranes in cavities.....................................................44
Thermal mass .........................................................................................44
Cold bridges...........................................................................................45
4.5 Green roofs and roof ponds..........................................................................45
Green roofs ............................................................................................45
Roof ponds ............................................................................................46
5 Windows ...........................................................................................47
5.1 Glazing materials .........................................................................................47
Heat transmission through glazing ..........................................................48
Radiation transmission through glazing...................................................50
High performance glazing ......................................................................50
5.2 Framing and support systems .......................................................................51
Obstruction of light due to framing ........................................................52
3456 EARTHSCAN Hndbk Sust Refurb:Layout 1 22/7/09 09:51 Page vii
The Handbook of Sustainable Refurbishment vii
Thermal performance of framing............................................................53

Framing material ....................................................................................54
5.3 Modifying apertures.....................................................................................55
5.4 Shading systems ...........................................................................................56
Daylight redistribution............................................................................56
Shading options for refurbishment ..........................................................57
External shading .....................................................................................57
Internal shading......................................................................................59
5.5 High performance daylighting .....................................................................60
6 Atria and Double Skins ......................................................................63

6.1 Atria and energy: Principles .........................................................................65
Thermal performance.............................................................................65
Winter performance ...............................................................................65
Summer performance .............................................................................67
6.2 Effect on daylighting ...................................................................................67
6.3 Planting and vegetation................................................................................68
6.4 Double skins and energy ..............................................................................68
6.5 Other environmental factors ........................................................................68
6.6 Atria and double skins as part of sustainable refurbishment ...........................69
7 Mechanical Services and Controls ........................................................71

7.1 Boilers .........................................................................................................71
7.2 Heat distribution .........................................................................................72
Water .....................................................................................................72
Air .........................................................................................................72
7.3 Heat emitters ...............................................................................................73
Positioning emitters ................................................................................75
Sizing emitters........................................................................................75
Coolth emitters ......................................................................................76
7.4 Fans and pumps ...........................................................................................76
7.5 Refrigeration...............................................................................................77
7.6 Lighting installations ....................................................................................77
Luminous efficacy...................................................................................77
Illuminance level and distribution ...........................................................79
7.7 Controls ......................................................................................................79
Local control ..........................................................................................79
Central control .......................................................................................80
Zoning ...................................................................................................80
7.8 Lighting controls..........................................................................................81
Occupancy detection..............................................................................81
3456 EARTHSCAN Hndbk Sust Refurb:Layout 1 22/7/09 09:51 Page viii
viii The Handbook of Sustainable Refurbishment
Daylight detection ..................................................................................82

Zoning ...................................................................................................83
Energy savings ........................................................................................83
7.9 Building energy management systems ..........................................................83
7. 10 Adaptive controls .........................................................................................84
Feedback ................................................................................................85
Caretaker controls...................................................................................86
7.11 Hybrid and mixed mode systems .................................................................86
8 Renewable Energy Options .................................................................89

8.1 Other renewable energy technologies ..........................................................89
Part Three Case Studies

9 The Albatros, Den Helder, The Netherlands ..........................................93
Objectives..........................................................................................................93
Refurbishment strategy ................................................................................93
The double skin.................................................................................................94
Performance of double skin ..........................................................................96
Ventilation and heating ......................................................................................96
Performance.................................................................................................97
Daylighting........................................................................................................98
Overall energy performance...............................................................................98
Comfort ..........................................................................................................100
Conclusions .....................................................................................................100
10 Lycée Chevrollier, Angers, France ......................................................101

Strategy for sustainable refurbishment...............................................................101
Main low energy measures ...............................................................................102
A.Thermal .................................................................................................102
B. Lighting .................................................................................................102
C. Comfort: Shading and ventilation...........................................................102
D. Other features ........................................................................................102
Insulation.........................................................................................................102
Daylight and artificial lighting ..........................................................................103
Artificial lighting ........................................................................................103
Performance...............................................................................................104
Ventilation .......................................................................................................104
Performance...............................................................................................104
The atrium ......................................................................................................105
Photovoltaic panels ..........................................................................................106
3456 EARTHSCAN Hndbk Sust Refurb:Layout 1 22/7/09 09:51 Page ix
The Handbook of Sustainable Refurbishment ix
Waste management and other environmental issues ..........................................106

Overall energy performance.............................................................................107
Gas consumption .......................................................................................107
Electricity consumption .............................................................................107
CO2 emissions............................................................................................107
Comfort ..........................................................................................................108
Conclusions .....................................................................................................109
11 Daneshill House, Stevenage, UK .........................................................111

Strategy for refurbishment................................................................................111
Main innovative energy-saving features ............................................................112
The CoolDeck system................................................................................112
Performance...............................................................................................113
Energy efficient air-conditioning controls ........................................................114
Performance...............................................................................................114
Energy-efficient lighting controls .....................................................................114
Performance...............................................................................................115
Light emitting diode (LED) lighting in Customer Service Centre ...............116
Solar water heating array..................................................................................118
Performance...............................................................................................118
Increased space use efficiency ..........................................................................119
Post occupancy evaluation................................................................................120
12 Ministry of Finance Offices, Athens ....................................................123

Refurbishment strategy ....................................................................................123
Main energy saving features .............................................................................124
Fabric improvements ..................................................................................124
Night ventilation techniques.......................................................................124
Ceiling fans ................................................................................................124
Daylighting and artificial lighting................................................................124
Heating ......................................................................................................124
Cooling......................................................................................................124
Ventilation..................................................................................................124
Energy management, control and monitoring .............................................125
Performance ....................................................................................................125
Thermal comfort and air quality.................................................................125
Daylighting and artificial lighting................................................................127
Daylighting performance ............................................................................127
The photovoltaic array .....................................................................................127
Heating ......................................................................................................128
3456 EARTHSCAN Hndbk Sust Refurb:Layout 1 22/7/09 09:51 Page x
x The Handbook of Sustainable Refurbishment
Cooling......................................................................................................128
Comfort surveys ..............................................................................................128
13 The Meyer Hospital, Florence ............................................................131

Refurbishment strategy ....................................................................................131
The greenhouse .........................................................................................132
Daylighting ................................................................................................134
Comfort ..........................................................................................................134
Appendices .........................................................................................................135
Index ................................................................................................................165
3456 EARTHSCAN Hndbk Sust Refurb:Layout 1 22/7/09 09:51 Page xi
Preface
In most European cities there is a vast stock of This guide is a product of the European
existing buildings, many of which are getting to Union (EU) funded REVIVAL project, which
the end of their useful life.To replace the stock set out to demonstrate some of these principles
would take several decades and incur an unreal- by incorporating them in five refurbishment
istic financial burden. It would also create a large projects of large non-domestic buildings.Wher-
contribution to CO2 emissions, as a result of the ever possible it draws from the experience of the
energy associated with the production of REVIVAL project, but includes other examples
materials and the construction of replacement and illustrations when necessary.
buildings. This guide is aimed at the architect, engineer,
It is therefore essential that we develop surveyor and project manager. It sets out the case
strategies and techniques to improve the energy for sustainable refurbishment and the principle
performance of our existing stock. It is commonly measures that can be adopted. It presents princi-
understood that the heating, cooling, lighting and ples in a concise technical language, but follows
ventilation of buildings accounts for nearly half of with an explanation of practical implications. It
global energy consumption, with the consequent does not attempt to be a source book of manu-
CO2 emissions having an effect on global warm- facturer’s information and technical data, or to
ing.The reduction of day-to-day consumption of deal with construction detail.
fossil fuels for heating, cooling, lighting and ven-
tilation must be the main objective in any attempt REVIVAL Team
to refurbish a building sustainably. July 2009
3456 EARTHSCAN Hndbk Sust Refurb:Layout 1 22/7/09 09:51 Page xii
List of Acronyms and Abbreviations
AC air-conditioned EPC Energy Performance Certificate

ANV advanced natural ventilation EU European Union
BEMS building energymanagement IR infrared
systems IRC internally reflected component
BREEAM Building Research Establishment LED light emitting diode
Environmental Assessment l/w luminaires per watt
Method MM mixed mode
CHP combined heat and power NV natural ventilation
CRC Carbon Reduction Commitment PAC partially air-conditioned
COP Coefficient of Performance PCM phase change material
CSR Corporate Social Responsibility PIR passive infrared
DEC Display Energy Certificate PSALi permanent supplementary
DEFRA Department for Environment, artificial lighting
Food and Rural Affairs PV photovoltaic
DF daylight factor SBS sick building syndrome
DX direct expansion SHF Solar Heat Gain Factor
EEAS Energy Efficiency Accreditation UV ultraviolet
Scheme
EPBD Energy Performance of Buildings
Directive
3456 EARTHSCAN Hndbk Sust Refurb:Layout 1 22/7/09 09:51 Page 1
Part One Principles

Strategy for Low

1 Emission Refurbishment
1.1 The case for low emission refurbishment: 2 The socio-economic impact.
Energy use in buildings
Initially, the environmental impact of refurbish-
In the non-domestic sector in Europe, building ment will almost always be less than demolition
refurbishments offer far more opportunities for and newbuild. This is because all the materials
reducing emissions than new building; the latter carry embodied energy – to replace them causes
represents annually less than 1.5 per cent of the new carbon emissions (Figure 1.1). Furthermore,
building stock. The usual motivation for refur- the demolition process and waste disposal cre-
bishment includes: ates carbon emission as well as other waste
disposal impacts.
• replacement of degraded finishes and
components;
• tailoring space organization to new uses;
• improving environmental quality.
Embodied CO2
These reasons may be sufficient in themselves to waste
justify the cost. If at the same time the building deliveries
can be made more energy efficient, there will be site energy

M&E
a reduction in running cost and a reduction in
cladding
CO2 emissions. This will often be at a modest
piling
extra cost that can be justified by reduced run-
steel
ning costs, or in some cases even, no extra cost.
concrete
raised floors
1.2 Refurbishment versus rebuild: internal partions
Economics and environmental impact roof covering
0 10 20 30 40
There are many instances when demolition and
% total
rebuild will be considered as an alternative to re-
furbishment. This could be justified purely on
economic grounds, or the advantages offered by Figure 1.1 Embodied CO2 associated with newbuild and
a new building could be considered to justify the refurbishment. Note large CO2 content for bulk materials
extra cost. However, two non-economic factors such as concrete and steel. Components made of these
should be considered: materials are the ones that are not normally replaced in
refurbishment
1 The environmental impact of refurbish- Source: Thomas Lane quoting the Simons Construction Group in ‘Our dark
ment versus newbuild. materials’, Building, 9 November 2007
4 Principles
Figure 1.2 CO2 emissions for

newbuild and refurbishment as a
function of time. The break-even point
is very dependent upon the difference
in performance (indicated by the slope
of the graph) of the refurbished and
newbuild.
It is often argued that a new building will oper- structure and the cleaning of concrete finishes
ate at higher energy performance than a will direct money to tradesmen that in the case
refurbished one, and that during its lifetime, may of new build would go to investors in concrete
have less environmental impact.This dynamic re- and steel manufacture.
lationship is shown in Figure 1.2. It demonstrates
two important effects – that newbuild is only the 1.3 The building, plant, and occupants as a
lowest emitter after the break-even time period, system
and that this period can be extended by im-
proved performance of the refurbished option. It Building simulations and analyses of monitored
also demonstrates that if the break-even time is data have shown that the building fabric alone
beyond the time of the environmental crisis (or does not narrowly determine the energy per-
emission reduction target), the life-cycle emis- formance. Figure 1.3 shows the performance
sion is irrelevant and the refurbished building is being determined by three sub-systems, each
the best choice. It is also evident that the break- having a variance in performance of about two-
even point is sensitive to the actual performance fold.When a poor building combines with badly
of the buildings; new buildings have not in gen- designed systems and poor management, the re-
eral performed as well as predicted and this will sulting energy performance can be dramatically
postpone the break-even point. worse than the best.This wide variation of per-
The second consideration is about social benefit formance has been observed as shown in Figure
and employment. Generally, refurbishment car- 1.4. It is interesting to note that building no. 92
ries a higher proportion of labour cost than (extreme right) was built in 1987 and refurbished
newbuild. For example, the repair of a concrete in 1992.
Figure 1.3 The building, the mechanical

services and the occupants, as a system. Each
environmental controls a range of performance. A poor
building services occupants performance building may require much input from
services which if badly managed leads to high
x 2.5* x 2.5 x 2.5 x 16 energy consumption. The reverse may also be
maximum range
of performance true. This accounts for a wide variance in
energy consumption of similar buildings
Strategy for Low Emission Refurbishment 5
However, there may be individual cases where

the inherent qualities of a building present insur-
mountable problems. For example, buildings with
very deep plans, relying entirely on air-condi-
tioning and artificial lighting, built in an era of
cheap energy (Figure 1.5), will always be prob-
lematic both for their energy consumption, and
internal environmental quality.Thus it is impor-
tant to properly assess the potential for
refurbishment, before conclusions are drawn.
Figure 1.4 The annual CO2 emissions per m2 for 92 office 1.4 Implications for change of use
buildings in the UK. The 20-fold variance illustrates the
interactive effect between building, services and occupants Refurbishment is often accompanied by change
Source: Data from Energy Consumption Guide 19 – Energy Efficiency in
of use.This may be across recognized use types –
Offices (1998) BRECSU, Watford for example a nursing area of a hospital becom-
ing an administrative centre (Figure 1.6), or a
change from residential to office use (Figure 1.7).
This evidence weakens the case for newbuild, Or it may be that within a use type the func-
since it shows that the inherent properties of the tional demands on spaces are changing due to
building are only one of the determining factors. reorganization and the impact of changes in
This is particularly true in non-domestic build- practice and technology. For example, develop-
ings where overall energy consumption is ments in IT have a continuing influence on
dominated by processes and activities in the office practice and the spaces that support it.
building. Both systems and management can be
of as high performance in a refurbished building
as in a newbuild.
Figure 1.6 REVIVAL building Meyer Hospital, Florence:

Refurbishment accompanies change of use from nursing
Figure 1.5 Deep-plan buildings such as these, built in the area to hospital administrative and reception area, involving
era of cheap energy and relying on air-conditioning and different environmental conditions
artificial lighting, may present insurmountable problems for
sustainable refurbishment
6 Principles
These changes may bring about benefits and dis-

benefits. For example, an historic warehouse
converted into a library will create a difficult
challenge to the designer if the intention is to
provide daylight, due to the shallow floor-to-
ceiling height. On the other hand, a heavyweight
building that required wasteful intermittent heat-
ing in its original function as a primary school,
would not be so inefficient if used for a much
longer occupied period as, for example, a health
clinic. Furthermore, the intermittent heating
would be less wasteful anyway if the envelope
insulation was improved as part of the refurbish-
ment package.
Figure 1.7 REVIVAL building The Albatros, Den Helder, The Thus, the inherent properties of the building,
Netherlands: Refurbished in conjunction with change of use the operational requirements of the new use, and
from residential to offices the technical options in the refurbishment all
have to be considered interactively.
It is difficult to generalize here, but it could be

Impact on energy consumption
said that opportunities are sometimes missed be-
cause designers impose stereotypical solutions, In spite of improvements to the performance of
often ignoring the serendipity of fitting a new the fabric and systems, change of use may bring
function into a building generated by a different about an increase in the energy consumption.
set of aims. This does not necessarily mean that the low-
For example, in a conversion of an old fac- energy refurbishment has failed, since the meas-
tory workshop to modern office use, high ures adopted have undoubtedly led to lower
ceilings with exposed structural slabs are often energy consumption than if absent.
replaced with suspended ceilings for acoustic In measuring the success of the refurbishment
reasons, and under the misguided impression that then, it would be fair to make a comparison of
the original spaces would be impossible to heat the building’s actual energy performance (shown
efficiently.This action not only destroys much of at A in Figure 1.8) with, firstly, the existing build-
the architectural quality of the space, but will also ing under the new use and complying with
have a negative influence on daylight distribu- accepted comfort conditions, but without adopt-
tion, natural ventilation and, possibly, thermal ing low-energy measures (B). Secondly, a
response. comparison should be made with a new build-
Change of use may bring about changes in ing of similar use type (C). We might expect a
purely technical parameters.These include: performance somewhere between these two or
with really successful refurbishments, even sur-
• occupancy pattern and density; passing typical newbuild performance. Finally, a
• internal gains; comparison should be made with the average
• lighting levels; emissions for the building stock of the same use
• ventilation rates; type (D).
• thermal set-points and response; The example here shows that the refurbished
• acoustic properties (reverberation time, noise building emits 35 per cent of that predicted for
exclusion). the original building with a change of use, and
58 per cent of that of the measured average for

the existing building stock, although it emits 10
per cent more than a new building.The fact that
the refurbished building with its new use emits
nearly twice that of the original building with
its original use, is not of much relevance.
refurb. building, new use.

ACTUAL A
original building, new use.

CALCULATED B
newbuild, new use.

CALCULATED C
average for building stock

of same use type. ACTUAL D
original. building, old use. Figure 1.9 An over-glazed lightweight building of the
ACTUAL
E
1970s suffering from overheating in summer and under-
energy consumption
heating in winter. The client’s perception is often that the
only solution to comfort problems is air-conditioning
Figure 1.8 Comparing like with like: Assessing the
improved performance of a refurbished building
standards achievable by air-conditioning may still
not be met for all of the year. However, it is now
widely accepted that for buildings running under
predominantly passive systems, occupant satis-
1.5 Environmental comfort standards faction can be high, even when the conventional
Improved comfort standards are often the initial standards are not met.
motivation for refurbishment. The building A key factor is the presence of adaptive oppor-
shown in Figure 1.9, an office block built in the tunity. This is the ability of the occupant to make
1970s, is poorly insulated with large areas of sin- changes to the environment, and/or make
gle tinted glazing, no shading and a poorly changes to their personal condition, in order to
controlled heating system. Since its original oc- improve their comfort.Typical opportunities that
cupation, density has increased, and there has might be present are listed below.
been a proliferation of computers and other
Positive adaptive attributes
business machines. The frequent complaint is
overheating in summer, both under-heating and • relaxed dress code;
overheating in winter, and poor air quality. • occupant mobility;
The client’s presumption may well be that full • access to hot/cold drinks;
air-conditioning would be the answer. If con- • openable windows;
ventional comfort standards were sought, this • adjustable blinds;
could indeed true, although this would be nei- • desk fan or locally controlled ceiling fan;
ther an economical nor environmentally friendly • local heating/cooling controls;
solution. • workstation/furniture flexibility;
If refurbishment measures included shading, • shallow plan (minimizing distance from win-
improving the envelope insulation, and reinstat- dows);
ing openable windows, comfort conditions • cellular rooms (reduces mutual disturbance);
would be greatly improved, although the strict • surface finishes appropriate to visual task;
8 Principles
• daylight and task lighting backup; take the predominantly passive option. Further-
• good views (external and internal); more, because of the intermittent nature of the
• transitional spaces (verandahs, atria, etc.); comfort cooling, and its controllability, it will not
• good access to outside areas. be necessary to apply such strict comfort limits
as in a conventional air-conditioned building.
Negative adaptive attributes This strategy, often referred to as ‘hybrid’ or
• uniformity of physical environment (temper- ‘mixed mode’, results in comfort cooling often
ature, lighting, colour); being a viable and energy efficient option.
• deep plan, reduced access to perimeter;
• dense occupation with restricted workstation 1.6 Passive environmental strategies
options;
• sealed windows; Statistically, air-conditioned buildings consume
• views obstructed by fixed shading devices; significantly more energy than naturally venti-
• central mechanical services control. lated buildings. In temperate climates, field
studies have shown that in spite of the extra cap-
Studies have shown (Baker and Standeven, 1994) ital and running costs, occupant satisfaction was
that the presence of several of the positive at- no greater than in naturally ventilated buildings
tributes will result in occupants tolerating (Figure 1.10). Even in hotter climates, as a study
temperature excursions typically up to 5°C of office buildings in Lisbon showed, satisfaction
above conventional upper temperature limits, in some air-conditioned buildings may be sig-
and around 3°C below conventional lower lim- nificantly less than in some naturally ventilated
its. This may allow the designer to opt for the buildings.Thus the strategy for avoiding air-con-
passive solution rather than the air-conditioned ditioning is a good one, although hybrid systems
solution. and comfort cooling (described later in section
This will have implications for initial cost, 7.11) may represent a viable alternative.
maintenance cost and carbon emissions. It will The situation often faced in refurbishment is
also have implications for the choice and prior- of a building with very poor comfort conditions,
itizing of refurbishment measures. For example, where air-conditioning is seen as the only solu-
if it were decided to air-condition the building, tion. However, it could be that after making
the replacement of standard double glazing with fabric and system improvements, comfort con-
high performance low-e units would have a ditions become acceptable.This should be tested
greater impact on carbon emissions than if the by analysis or simulation before the air-condi-
building were to be freely ventilated by open- tioning option is adopted.
able windows. This is because the temperature This may even apply to a building that has air-
differential in the latter case would be small or conditioning already. Many over-glazed buildings
even non-existent. However in both cases, shad- of the 1960s and 1970s were subsequently air-
ing would be highly beneficial. conditioned to make conditions bearable.
In some cases, exceptional overheating con- However, measures such as shading, fabric insu-
ditions may be unacceptable, although lation, reduction of glazing area, adoption of
conditions prevailing for most of the year may adaptive controls, may well render full air-con-
be satisfactory without air-conditioning. In this ditioning unnecessary. Even if air-conditioning
case, intermittent comfort cooling may be ap- is adopted, these measures will reduce the air-
plied. The technological aspects of this are conditioning loads significantly.
discussed in section 7.11. Here we make the
point that a modest dependence on comfort
cooling may result in a building being able to
Figure 1.10 Overall occupant comfort by

ventilation types; natural ventilation (NV),
advanced natural ventilation (ANV), mixed
mode (MM) and air-conditioned (AC). The
coloured plots are for the PROBE (UK) survey
and the open plots from the Building Use
Studies data. Summer survey results from 26
office buildings in Lisbon show that occupant
satisfaction in naturally ventilated buildings
(NV) and partially air-conditioned buildings
(PAC) was higher than in air-conditioned
buildings (AC)
Source: The Probe Study (2001) Building Research and
Information, vol 29, 2 March
Natural ventilation Refurbishment measures to reduce uncontrolled

infiltration must then recognize the need to pro-
Many candidate buildings for refurbishment will vide ventilation to ensure that a minimum air
have high rates of infiltration.This is particularly quality is maintained. This does not mean that
true of buildings constructed using pre-cast con- the benefits of the more airtight envelope will
crete components, and panel and curtain wall all be lost, provided some means to prevent over-
systems, with dry linings – typical construction ventilation is present. Broadly, the principle is
techniques of the 1960s to 1980s era (Figure ‘build tight, ventilate right’.
1.11). In buildings with original glazing systems, In predominantly warm climates (i.e. with lit-
these too were very leaky. In cooler climates, the tle winter heating) reduction of infiltration only
result of the high infiltration rate is a waste of brings energy benefits if the building is air-con-
energy due to heat loss. However, one benefit of ditioned to a temperature significantly below the
the high air-change rate was good air quality. prevailing outdoor temperature. If it is not to be
air-conditioned the main concern switches to
getting enough ventilation to remove heat gains
and to generate air movement.This will demand
large openable areas.
Night ventilation
A further important function may be the provi-
sion of night ventilation to cool the structural
mass.The principle is illustrated in Figure 1.12.
This function will also require large openable
areas in the envelope, and unobstructed flow
paths within the building. Furthermore, it is es-
Figure 1.11 REVIVAL building Lycée Chevrollier, Angers,
sential that the ventilating air can be thermally
France: Built in 1958 of pre-cast concrete construction with
coupled with the thermal mass of the building.
dry lining and poorly fitting metal windows, it had very high
These requirements may present design chal-
infiltration rates before refurbishment
lenges, particularly in relation to security and
noise control.
10 Principles
Figure 1.12 The principle of night

ventilation: The mass of the
building is cooled at night to
provide a heat sink for internal
gains during the day
2
23°C 17°C 23°C 27°C
acoustic
vents
G
maximum ventilation minimum ventilation
Daylighting
For the two or more centuries since the indus-
trial revolution, when man moved indoors,
daylight had been too valuable an asset to waste.
Architects responded by a whole typology of
window and rooflight designs, readily accepting
the need for shallow plans, light wells and court-
yards (Figures 1.13, 1.14). This constraint was
reinforced by the same need for shallow plan to
achieve good natural ventilation. Whilst, of
course, artificial light had to be employed after
the hours of darkness, daylight was always the
preferred source in the daytime, and artificial
light was regarded as inferior both technically
and on health grounds. The latter dated from
pre-electric times when oil and gas lighting cre-
ated serious levels of indoor pollution and fire
risk.
The development in the 1950s of the fluorescent
lamp, together with relatively cheap electric en-
ergy, prompted designers to question the need
to provide the working illumination by daylight
(Figure 1.15). This freed them to adopt deeper Figure 1.13 Wauquez Department Store (now a museum
plans, which in principle made economies in of cartoon art), Brussels: Rooflighting the top floor (1920).
space efficiency and building cost. The architect Horta could not resist architectural elaboration
Figure 1.14 County Hall, London, 1908: Even large buildings were in fact shallow plan, providing access to daylight and natural
ventilation
Buildings of the 1960s to 1980s found them- the poor light distribution due to large areas of
selves at a crossroads. On the one hand glass and side-lighting was balanced by artificial lighting
glass-supporting cladding technology had made away from the perimeter zones. The next re-
great strides to support the modernist, minimal- sponse was to reduce the light transmittance of
ist view of facade design, often with huge areas the windows to values as low as 25 per cent, with
of glazing (Figure 1.16). On the other hand, the tinted and reflective glass (Figure 1.17). Finally
improvement by a factor of five in the luminous the contribution of daylight was abandoned al-
efficacy (lumens light output per Watt electrical together. This allowed a retreat into deep plan,
input) of the fluorescent lamp over the incan- and for a brief period a knee-jerk response of
descent lamp meant that it was now technically drastically reducing glazing areas. The resulting
and economically feasible to provide the work- deep plan, air-conditioned, artificially lit build-
ing illumination entirely artificially. ings from this era have proved to be the highest
The result of these conflicting influences meant energy users and the most likely candidates for
that the art of good daylight design was virtually sick building syndrome (SBS) (Figure 1.18).
lost. Initially the over-glazed buildings were, not Within our target building group all of these
surprisingly, over-illuminated leading to glare, types will be found.The following Table 1.1 pro-
overheating in summer due to solar gain, and vides a response strategy.
suffering from large heat losses in winter. Re- Finally, the benefits of daylighting and good
sponse to these included, ironically, permanent window design extend beyond the saving of en-
supplementary artificial lighting (PSALi) where ergy. There is growing evidence that the view
12 Principles
from windows and the perception of the pres-

ence of daylight, even without direct views, is
valued by occupants.This can lead to increased
well-being and productivity, and also increased
tolerance of non-neutral environmental condi-
tions. The latter offers significant support to the
adoption of a passive strategy.
Figure 1.15 The leap forward in luminous efficacy of the

fluorescent lamp heralded the daylight dark ages. Deep-plan
buildings abandoned daylight and natural ventilation, and
windows were relegated to providing occasional views
Figure 1.17 First efforts to overcome the effect of large

areas was to reduce the transmission of glass by reflective
and absorptive glasses
Figure 1.18 The Kalamazoo building, Birmingham,

completely abandoned daylight with deep plan, slit
Figure 1.16 The transparent building – huge areas of windows and full air-conditioning. Buildings of this type are
glazing and shallow plan: Delft University, circa 1960 prime candidates for sick building syndrome. It was
demolished in 2003.
1.7 Prioritizing refurbishment options to daylight will reduce energy consumption and
be seen as a positive move by most occupants.
Most building projects, whether refurbishment The interaction of types of benefit (i.e. envir-
or newbuild, are ultimately budget limited. onmental or personal) and the sometimes
Budgets will constrain both sustainability meas- conflicting, sometimes mutually supporting, out-
ures and functional design solutions. In the comes, makes the prioritizing of refurbishment
former case, a typical example might be the in- measures difficult. Consider the case where two
stallation of a photovoltaic array technically measures – insulating the roof or installing shad-
possible to meet the equivalent electrical load of ing devices – are of similar cost, but have
the building (we will call this environmental bene- different levels of impact on the occupants. Roof
fit), but prevented by prohibitive cost. In the insulation will bring economic benefit to the
second example, a more generous budget for fur- building operator, environmental benefit due to
nishings would be regarded as desirable but not reduced heating load, but no personal benefits.
viable (we will call this personal benefit). In some On the other hand, shading devices will improve
cases, budget constraints may interact with deci- personal comfort conditions, may improve the
sions which affect both of these areas – for appearance of the building, and if the building is
example, limiting the space provision per occu- to be air-conditioned, may reduce cooling loads.
pant will probably be seen as a reduction in How do we resolve this question? We suggest
quality from the occupant’s point of view, but that the environmental benefits and personal
may well improve the energy use per occupant. benefits have to be treated separately, initially.
In other cases, a measure may create benefits in When there is a clear quantitative ranking of en-
both categories – for example, improving access vironmental measures, then personal benefits
Table 1.1 Daylighting strategies for refurbishment
Building type Daylight status Refurbishment strategy
Shallow plan, small glazing area Daylighting provision degraded.1 Reinstate daylighting, install photo-responsive
controls.
Shallow plan, large glazing area Daylighting degraded by low Consider reduction of glazing area, high
transmissivity glass or fixed shading, performance daylighting2 (adjustable shading and
or nothing. high performance glass). Install photo-responsive
controls.
Deep plan, large glazing area Daylighting abandoned even in As above for perimeter zone. Consider advanced
perimeter zone, as above. High daylight options to increase daylight penetration.
levels of uniform artificial light. Install rooflights (top floor) and consider light
wells. Install task lighting with low illuminance
photo-responsive background lighting.
Deep plan, small glazing area Daylight abandoned. High levels Consider increasing glazing area together with
of uniform artificial lighting. measures above.
1 Daylighting performance may be degraded by inappropriate shading design, internal or external obstructions, poor distribution due to lowered ceilings and low
reflectance surfaces, deliberate reduction of transmission of glass by films or paintwork.
2 The term high performance daylighting refers to the technical means to balance the usefulness of daylight to perform the visual task, and the positive benefits of
view, with the disbenefits of overheating and glare (see ‘High performance daylighting’ Appendix).
14 Principles
should be considered. This is not because the mate will have far greater benefit than in a mild
personal benefits are any less important, but be- climate, whereas the case for shading devices
cause they are far less easy to quantify.There may might be reversed. Similarly the building type
be cases, however, where the personal benefits will influence priorities – a shallow-plan school
are the primary concern, or may even be essen- building occupied predominantly in the day will
tial – for example, the replacement of asbestos benefit far more from the investment of im-
with a non-toxic insulant. proved daylight access than an institutional
Table 1.2 below is indicative only. All of the building occupied for 18 hours per day. There
benefits are dependent on circumstances – for are too many combinations of parameters to at-
instance, the impact of improving plant efficiency tempt comprehensiveness; rather, this example is
obviously depends on the existing efficiency and given as an illustration of the interaction of
the final efficiency. measures and the strong impact on priority.
To assess these scenarios we have used the LT
Europe software. This software developed from
Quantifying energy benefits
the LT Method takes account of the interaction
Here we review typical refurbishment options between lighting heat gains, solar gains, occupant
and apply them to a range of scenarios. Of gains and losses through the envelope elements
course it is not possible to create global ranking and ventilation. It evaluates energy inputs for
of measures since their performance is very sen- heating, lighting, ventilation and cooling, and can
sitive to the context. For example, improving indicate comfort levels resulting from the omis-
envelope insulation to a building in a cold cli- sion of mechanical cooling. It can also evaluate
Table 1.2 Environmental and personal benefits of refurbishment measures
Technical measure Potential environmental benefit Potential personal benefit
Change fuel type large zero
Improve plant efficiency large zero
Improve controls large moderate
Insulate envelope large zero to small
Improve daylight access moderate moderate
Install shading moderate moderate to large
Install task lighting moderate large
Increase occupant density moderate -ve small
Improve noise control zero large
Improve art. light spectral qual. -ve small small
Reduce occupant density -ve moderate moderate to large
Provide comfort cooling -ve moderate large

Note: Environment refers to global environment.
Figure 1.19 Case comparison from the LT

Europe software showing the progressive
improvement in energy and overheating
performance for natural ventilation and air-
conditioning
set-point. In the naturally ventilated

case, overheating is defined as the
number of days with two consecutive
hours or more above 27°C.
The example studied here is a typ-
ical 1970s medium-sized four-storey
office block with a 14m ⫻ 34m foot-
print. It is set in an open site in the
UK, where there is both a significant
heating and cooling load. The build-
ing is glazed on both long facades that
face north and south, with single glaz-
ing occupying 70 per cent of the
facade area.The envelope is leaky and
poorly insulated (U-values around
1.5). Due to lack of solar controls, and
internal gains due to low efficiency
lighting and fast growing IT installa-
tions, frequent overheating has
prompted the installation of air-con-
ditioning, together with tinted
window film. Controls are poor, and
the centrally switched lighting is on all
day. Occupant satisfaction is very low,
energy costs high, and it is now in dire
need of refurbishment.
Figure 1.19 shows the case com-
parison, displaying the total primary
energy consumption for the base case
described above (labelled case 1) fol-
lowed by the application of 11
measures aimed at improving energy
the impact of thermal mass and the benefit of performance. This shows firstly how
night ventilation the measures interact, and secondly provides
The software computes the energy in primary some evidence as to how their cost effectiveness
energy units, which closely relate to CO2 emis- could be ranked, although the cost of the meas-
sions. The cooling loads are calculated on a 25°C ures is not given explicitly.
16 Principles
The cases explored are as follows: proved to 40l/w and the design luminance re-
duced to 200 lux, made possible due to the
Case 1 base case widespread use of self luminous computer
Case 2 base case + low-e glazing screens, and task lighting where necessary. This
Case 3 base case + boiler efficiency halves the lighting energy. But there is a penalty
increased from 65 per cent to 85 per to pay in heating, and about half of the decrease
cent of energy is lost. However the net effect for the
Case 4 base case + high efficiency lighting air-con case is a reduction of 21 per cent, and 30
Case 5 (4) + vent rate reduced 1.5ac/h to per cent for the naturally ventilated case, and is
1.0ac/h, boiler efficiency increased thus, together with the increased boiler effi-
from 65 per cent to 85 per cent ciency, certain to be far more cost effective than
Case 6 (5) + photoelectric lighting controls the low-e glazing. Note too, that there is a sig-
Case 7 (6) + low-e glazing nificant reduction in overheating days, which had
Case 8 (7) + insulated opaque envelope actually increased with the low-e glazing. How-
Case 9 (8) + reduced glazing area ever, overheating days are still around 28, which
Case 10 (9) + summer high vent is unacceptable.
Case 11 (10) + night ventilation
Case 12 (11) + high thermal mass Case 5. The increase in heating load prompts
two measures to improve the thermal perform-
Case 1. The building starts with high heating, ance. One is to improve the airtightness of the
lighting and cooling loads. Without air-condi- envelope, reducing the infiltration from 1.5 to
tioning, overheating is around 45 days per year, 1.0 air changes per hour (ac/h), which may
about ten times an acceptable level. Clearly the prove to be a technical challenge, and secondly to
air-conditioning was essential. improve the heating plant further to an efficiency
of 0.9, achievable with a condensing boiler.This
Case 2. Here the envelope is identified as hav- largely compensates for the loss of heat gains
ing poor thermal performance and it is proposed from the lighting.
to reglaze with low-e double glazing.This is an
expensive option and the results are disappoint- Case 6. Lighting energy is reduced further by
ing with only a 10 per cent reduction in energy. the installation of photo-sensitive controls. As
can be expected for a shallow-plan building with
Case 3. This shows a much cheaper option of (more than) adequate glazing area, a large saving
increasing the boiler efficiency from 0.65 to 0.85 is made, reducing the lighting energy to about
per cent which shows a saving of 8 per cent. In 35 per cent of the uncontrolled value. It is worth
reality, this may reduce emissions further due to noting, that if this had been applied before the
improved combustion. It will also cause much efficiency of the lighting had been improved, the
less disturbance to the use of the building. absolute savings for this measure, and thus its cost
effectiveness, would be even greater. In this case
Case 4. This returns to the single glazing to con- the reduction in lighting energy has only led to
centrate on the other large component, lighting. an increase in heating energy of about 10 per
The existing lighting situation is bad, with poor cent, and this is probably because the lights are
efficiency lamps and luminaires only delivering going off in the middle part of the day, when for
20 useful lumens per watt (l/w)1 with a design most of the year net heating loads are very small.
luminance of 300 lux. This can easily be im- However, together with case 4 it does demon-
1 This includes the lamp efficacy and the utilization factor of the luminaire and room combination.
strate the dependence of heating loads on casual possible in summer, and overheating can be fur-
gains. ther reduced as in case 10.
Overheating has steadily reduced, down to 20
days, and there is now a real possibility of aban- Case 11. But overheating is still around 14 days
doning air-conditioning. So from now on, we will per year. Night ventilation is known to be effec-
concentrate on the natural ventilation option. tive in cooling the structure at night with the
cooler night air, and preparing the thermal mass
Cases 7 and 8. We now return to test the effects to absorb gains made in the daytime. Case 11
of improvements to the envelope, and in case 7 with night ventilation shows a significant reduc-
low-e glazing is installed again.This results in a tion to seven days.
40 per cent (of case 6) reduction in the heating
load. When combined with insulation to the Case 12. Here an attempt to make further im-
walls and roof (case 8) the reduction in heating provements is tested, where during the fit-out,
load is 64 per cent (of case 6).This is of course a structural mass is exposed by removing suspended
very expensive measure, and still could be of rel- ceilings and carpeted floors. This reduces over-
atively poor cost effectiveness. However, if there heating to four days, but at the expense of some
was already a need for fabric improvements due extra heating due to intermittent occupation.
to failure in weathering function, much of this
cost would be offset. Conclusions
The series of cases shows the interaction be-
Case 9. In case 9 the glazing area is reduced tween measures and their varying impact.
from 70 to 35 per cent on both south and north Although generic costs are not provided expli-
facades.This has little effect on energy balance – citly, it is quite clear that the measures will vary
there is only a small increase in lighting energy, widely in cost effectiveness, and this should be
and the reduction of heat loss from the north fa- borne in mind when establishing the priority of
cade is compensated by a loss of useful heat gains upgrading measures.
on the south facade. However, this strategy car- It also demonstrates that a critical point in
ries two important advantages. Firstly it reduces temperate climates is the ability to move from
unwanted solar gains, significantly reducing over- air-conditioning to natural ventilation. This is
heating; secondly, it reduces the cost of low-e partly because air-conditioning carries a large
glazing; and thirdly, if expensive shading treat- overhead of fan and pump energy, which is not
ment is necessary, it will be needed on a much directly proportionate to the cooling (or heat-
smaller area. It should be noted that the reducing) load.The result, in this case, of moving from
tion would have had a much bigger impact on the air-conditioned base case, to the naturally
heat loads had the glazing not already been up- ventilated final case is a reduction in primary en-
graded to low-e. ergy consumption of 81 per cent. It must be
pointed out, however, that improvements could
Case 10. However, the improved thermal per- have been made in the efficiency of the air-con-
formance of the envelope has had a downside ditioning system that are not tested here, and
with a disappointing increase in overheating due which would have reduced the final difference.
to the reduced heat losses (case 8), only partially Although some of the discussion has referred
compensated by the reduced glazing area. How to percentage changes, in order to indicate im-
do we increase heat losses on demand? By open- pact, ultimately it is the absolute reduction of
ing windows. When air-conditioning had been energy or CO2 emissions against which a meas-
installed, the windows were sealed. By reinstating ure should be judged. Thus a further large
openable windows, high air-change rates are percentage reduction to a load that has already
18 Principles
been reduced to a small value, is

less cost effective.This implies that
the order that measures are applied
is important.
Climate will affect the relative
impact of measures. In warmer and
sunnier climates, insulation will
have less impact in the naturally
ventilated case, and measures to re-
duce overheating more. Similarly,
building type will influence the
relative impact of measures. A
building such as a junior school
occupied for the middle part of the
day will benefit more from im-
provements to daylighting than, say,
a hospital, occupied for 24 hours
per day, whereas in the case of thermal improve-
ments to the fabric, the reverse may be true. Figure 1.21 Plan of Lycée Chevrollier showing the new
block N which caused some obstruction to daylight
available in the original block H
1.8 Integration with newbuild
Refurbishment projects often include varying
degrees of newbuild (Figure 1.20). This could We can identify two broad categories of integra-
range from a small wing or extension, to major tion that could affect environmental performance.
separate blocks totalling a built surface as great
or greater than the original building. In some 1 architectural
cases this may involve demolition and replace- 2 engineering.
ment, and in others, the newbuild may simply
be intensifying the site coverage. Architectural integration includes consideration for
the massing of the final building as well as the
aesthetic and stylistic qualities of both old and
new. Only the former issue is dealt with here.
The massing of a complex building or group
of buildings can have a significant effect on the
availability of daylight, the penetration of sun-
light and the microclimate of spaces around and
enclosed by the buildings. For example, on a visit
in spring to the Lycée Chevrollier building, it
was observed that the classrooms in block F had
lights on, whilst most in block E were off.This
clearly is a result of the obstruction of the new
block C (Figure 1.21).This new block will also
Figure 1.20 The new wing and atrium built as part of the affect availability of lower angle sun, and thus
Lycée Chevrollier (Angers, France) refurbishment. The old may reduce existing overheating problems, and
wing is on the right behind the retrofit shading hence the need for shading.
This illustrates the need to give full consider- range of principles, from near-spiritual attitudes
ation to the environmental impacts of the new about ‘living with nature’, to more pragmatic is-
massing and interaction of all parts of the pro- sues such as waste recycling and low carbon
ject.Another REVIVAL example is shown in the transport systems.
Meyer Hospital Case Study (Chapter 12) where The prefix ‘eco’ (from the Greek echos – home),
the addition of a new greenhouse on the south is rather widely used, but refers here to the con-
elevation affected the daylighting of the adja- cept of interdependence of buildings, the activities
cent office rooms in the original building. within them, and their occupants, in some syner-
Engineering integration is concerned mainly gistic way, that also supports sustainability and
with the integration of services. In particular, minimizes negative impacts on the wider envir-
heating plant may serve all parts of the project, onment. It is essentially opportunistic – just as in
and according to the amount of increase of built ecology, in the conventional biological sense, we see
surface area, the plant capacity may have to be different organisms occupying niches in a con-
adjusted. On the other hand it could be that ex- tinuous cycle of energy and material, so too in this
isting plant will be adequate for an increased more human-dominated context we see activities
built area due to the savings made by the im- and land use having a similar interdependence lo-
provement to the existing refurbished part. In cally, and thereby reducing global dependence.
any event, unless the heating plant has been re- There are three reasons why it is of relevance
newed recently, and the distribution mains are of in refurbishment projects. Firstly, the project may
a good standard, new plant, properly sized for the be quite extensive – particularly if it includes
total development, is likely to be cost effective. housing where many units may be refurbished
One further consideration, where the project by the same principles. Clearly there are oppor-
is an extensive building complex, is that distrib- tunities here to consider the area as a whole, how
uted plant may be the best option.This is because it interacts within itself and how it interacts with
distribution mains for heating and cooling are its immediate surroundings.
costly in capital, maintenance and running costs, Secondly, some building types naturally inter-
and with modern IT control and building en- act with their surroundings both socially and
ergy management systems, personal physical physically. For example, a refurbished factory will
presence to control plant in a central location is need a workforce which in turn will require
far less necessary than it used to be. transport and/or accommodation. It may also
produce low-grade heat as a by-product, which
1.9 Eco-communities and urban renewal could be used for space heating via a district
heating system.
This is a planning concept concerning commu- Finally, it is particularly relevant in urban re-
nity-scale policy and design rather than newal areas, where the refurbishment may cover
individual buildings. The term covers a wide groups of buildings of differing use types, as well
Figure 1.22
Eco-community renewal
scheme at New Islington, UK
20 Principles
Table 1.3 Potential for eco-interaction in large scale as infrastructure, and changes of land use (Figure
renewal projects 1.22).
In the example above, this will have implica-
ENERGY SUPPLY
tions for decisions made in the refurbishment of
Heat Group solar thermal both the housing and the factory, at a strategic
Waste industrial heat
and detailed technical design level.At a strategic
Heat from sewage and waste water
Heat from waste incineration level, the decision to use waste heat has a polit-
Combined heat and power ical aspect, since it will affect the cost both in
Group solar thermal money terms and carbon emissions, and will re-
Waste high-grade biomass quire management, and should bring benefit to
Biomass production from crops
both the user and the producer. At a technical
Ambient sources
Geothermal (and cool) level the use of waste heat rather than individual
Marine (and cool) heat sources may require heat emitters that can
Electricity Combined heat and power function at low water temperatures, and exter-
Shared wind power nally will require consideration for the routing
Shared solar thermal with storage of the heating mains.
Shared PV arrays To the left is a table of the most likely possi-
Hydro power
Tidal power
bilities for eco-interaction in relation to
refurbishment projects. Most are concerned with
ENERGY CONSERVATION AND COMFORT energy production, but some are concerned with
Microclimate Wind sheltering with vegetation energy and resource conservation.
Wind sheltering by buildings
Wind access in summer 1.10 Environmental regulation
Solar shading with vegetation
Solar shading by buildings Building refurbishment is increasingly being
Solar access in winter
brought under mandatory control in Europe and
Building specification Maintenance
this is a trend that is likely to continue. The
Technical support
European Commission is driving forward vari-
Outdoor amenity space Microclimate
Accessibility
ous initiatives with which individual Member
Adaptive opportunity States must comply but also individual countries
Privacy are introducing further requirements for both
Security new and existing buildings.
Management
Gardens and food production
Transport Access to public transport network Energy Performance of Buildings Directive
Cycle paths
Cycle storage and security
Footways
DIRECTIVE 2002/91/EC OF THE
Car parking and access EUROPEAN PARLIAMENT AND OF
Transport sharing schemes THE COUNCIL of 16 December 2002 on the
Traffic management hierarchy energy performance of buildings
Water and sewage Rain water catchment The Energy Performance of Buildings Directive
Greywater management
Reedbed purification
(EPBD) is the European driver for improving
the energy performance of all buildings in all
Waste disposal and recycling
Waste sorting European countries. Each country is required to
Compost translate the Directive into national legislation
Re-use according to an agreed timetable.
The EPBD is designed to provide informa- Implementation:The example of UK

tion on the energy performance of a building to Article 6 of the EPBD is translated into UK
prospective buyers and tenants, or in the case of legislation via Building Regulations.
‘public’ buildings, the information is to be dis- Building refurbishments that accompany a
played inside the building to inform all visitors. ‘change in use’ are subject to energy use, and
The objective is to raise awareness of the energy other provisions, of planning and Building Reg-
use of buildings, allowing prospective buyers and ulations control. Replacements to building
tenants to make informed decisions, and en- envelope components, including windows, ven-
couraging building owners and occupiers to tilation equipment and mechanical and electrical
improve the energy performance of new and ex- services, must comply with the Building Regu-
isting buildings. lations 2000. Additionally, building energy
The main components of the EPBD relevant performance must be improved when major re-
to existing buildings are given in the two boxes furbishments are conducted for buildings over
below. 1000m2. Energy requirements for building ex-
tensions and the commissioning of services are
Article 6: Existing buildings also included in Building Regulations. Large-
scale refurbishments, or those that lead to a
Member States shall take the necessary measures
change in use of the building, may result in the
to ensure that when buildings with a total useful
project being considered equivalent to a new-
floor area over 1000m2 undergo major renovation,
build.
their energy performance is upgraded in order to
The energy efficiency provisions of Building
meet minimum requirements in so far as this is
Regulations will continue to be used by gov-
technically, functionally and economically feasible.
ernment to drive improvements in the existing
building stock; it is the intention that forthcom-
ing updates planned for 2010 and 2013 will
Article 7: Energy performance certificate
further strengthen the energy performance re-
1. Member States shall ensure that, when build- quirements of refurbished buildings.
ings are constructed, sold or rented out, an
energy performance certificate is made avail- Article 7 of the EPBD requirements have been
able to the owner or by the owner to the transposed into British legislation and are com-
prospective buyer or tenant, as the case might ing into force in England and Wales between
be. 2006 and 2011. Legislation will be coming into
force in Scotland and Northern Ireland over a
2. Member States shall take measures to ensure
similar period.
that for buildings with a total useful floor area
over 1000m2 occupied by public authorities and
Energy Performance Certificates (EPCs) are
by institutions providing public services to a
based on the Asset Rating (a calculated annual
large number of persons and therefore fre-
energy consumption based on a standard use of
quently visited by these persons an energy
the building). EPCs provide the building’s rela-
certificate, not older than 10 years, is placed in
tive energy efficiency in a similar form to
a prominent place clearly visible to the public.
domestic product energy ratings, and must be
provided to prospective buyers or tenants when
a building is constructed, sold or rented.
22 Principles
Display Energy Certificates (DECs) are based carbon reductions of 1.1 Megatonnes of carbon
on the Operational Rating, that is the measured per year expected by 2020.The Department for
annual energy consumption of the building. Environment, Food and Rural Affairs (DEFRA)
DECs are required for buildings over 1000m2 is currently determining how the CRC will op-
occupied by public authorities or other institu- erate, with implementation expected in January
tions that provide public services to a large 2010.
number of people, from October 2008. DECs
must be prominently displayed in the building to
Voluntary schemes and drivers
inform visitors.The government has committed
to consult on the possible widening of these re- Various voluntary standards have also been de-
quirements to privately owned or occupied veloped for reducing energy use in existing
public buildings including retail outlets, cinemas buildings; such standards are often a precursor to
and hotels. EPCs and DECs are produced by ac- further mandatory controls.Voluntary schemes
credited energy assessors and are accompanied may be strong drivers for refurbishing buildings
by a report detailing voluntary options for im- to low carbon standards, and are used by some
proving the energy efficiency of the building. organizations to impose standards on buildings
they occupy. In the UK BREEAM (Building
Research Establishment Environmental Assess-
Using other legislation in the UK
ment Method) has for many years been accepted
There has been a clear trend for at least the last by industry as a general standard for assessing the
decade to reduce energy consumption in the ex- environmental sustainability of non-domestic
isting building stock, with Building Regulations, buildings, has been an important driver for the
planning policies and requirements regarding the improvement of the building stock and has been
provision of information to stakeholders all pro- widely used for promotional purposes. Many or-
gressively strengthening. ganizations have environmental policies and
regularly report on their Corporate Social Re-
Planning policies. Local planning policies sup- sponsibility (CSR). Carbon emissions form a key
ported by government legislation and Regional element of this, with energy efficiency creden-
Planning increasingly require developments to tials often highlighted as an indicator of a
use local heating networks (where available) responsible approach in the community. Year on
and/or to use renewable energy sources (on, near year improvements in reducing carbon emissions
or off site) to supply a proportion of their energy are usually a component of this reporting, with
requirements. Exact local planning requirements upgrading existing building stock a common ac-
regarding building refurbishments can differ sig- tion item.
nificantly between local authority areas. As such, The UK Energy Efficiency Accreditation
local planning requirements should always be Scheme (EEAS) is the leading independent
consulted prior to any refurbishment. emission reduction award scheme in the UK and
is open for both commercial and public sector
Carbon Reduction Commitment. The Car- organizations. The Scheme provides advice for
bon Reduction Commitment (CRC) is a new improving energy efficiency and requires
scheme, announced in the Energy White Paper demonstrated improvement in energy perform-
2007, which will apply mandatory emissions ance to secure accreditation. By gaining and
trading to cut carbon emissions from large com- maintaining accreditation, organizations involved
mercial and public sector organizations (including in the Scheme are able to raise the profile of de-
supermarkets, hotel chains, government depart- livered energy and carbon reductions both
ments, large local authority buildings), with internally and externally, and can benefit from
ongoing support to deliver further emission re-

ductions through membership of the Accredited
Organizations Network.
References
Baker, N. and Standeven, M. (1994) ‘Thermal comfort in
free running buildings’, Energy and Buildings, vol 23,
pp175–182
Part Two Practice

Floors
2
2.1 Solid ground floors Option 2: Load-bearing insulation above slab
with lightweight decking above.
Most solid ground floors being considered for This behaves as a lightweight construction since
refurbishment will be non-insulated. the mass is isolated by the insulation.The floor fin-
ish will have little effect on thermal response.
Original floor: Solid ground slab with screeded
finish.
Option 3: Raised floor with rigid or non-rigid
There is some uncertainty about the actual in- insulation (quilt) on original floor.
sulation value of non-insulated ground floors. It Raised floors are used where access to com-
is very dependent upon the properties of the munications wiring and services are required
subsoil. The literature provides values ranging across the whole floor.They may also be of value
from 0.3 for large buildings to 1.0 for small shal- where underfloor voids are to be used as part of
low-plan buildings. The dependence on size is a natural ventilation system. It must be noted
due to the three-dimensional nature of the heat however, that with wireless IT technology the
flow. The outcome is that large buildings may demand for raised floors for IT servicing has di-
have relatively low floor U-values already, and minished.
the cost benefit of floor insulation may be poorer
than for other parts of the envelope. Option 4: Replaced slab with rigid insulation
beneath.
Insulation options This would only take place in major refur-
bishment, or in new parts of a building. It offers
Option 1: Load-bearing insulation above slab both high insulation and large thermal mass.
with reinforced screed above. These options are illustrated in Figure 2.1.
This provides some insulated thermal mass,
which will offer some of the beneficial functions
of thermal storage associated with heavyweight Underfloor heating or cooling
construction. The beneficial effects of thermal Underfloor heating (or cooling) pipes can be in-
mass will be fully realized if dense conductive corporated in floor options 1, 2 and 4. The
materials (e.g. ceramic tiles) are used as a floor thermal mass of the screed in option 1 will result
finish, but reduced if finishes such as carpet are in a slow response emitter which could lead to
used. For screed thickness of up to 75mm, this control problems where rapid changes in heat
amount of thermal storage would be significant loads and gains are expected. Option 4 will have
for 24-hour cycles only, due to its isolation from a very slow response (days rather than hours), and
the thicker ground slab. would give control problems in all but continu-
ously occupied buildings with very constant
gains profiles.
28 Practice
solid floor 2.2 Suspended ground floors

screed
The insulation value of the non-insulated sus-
slab
pended floor is dependent on the degree of
soil ventilation of the underfloor void. For traditional
ORIGINAL
timber floors, this is often quite high and results
in the U-value being significantly higher – typ-
reinforced screed 50 - 75mm ically around 1.5 – than for a solid floor.
rigid insulation 50 - 100mm Reducing the ventilation rate would reduce this
slab
but would lead to high humidity and subsequent
decay of the timber. For non-timber floors the
soil void is also normally ventilated, to avoid con-
OPTION 1
densation.
timber or timber product deck Original floor A – screed on hollow ceramic pots
rigid insulation 50 - 100mm
between steel joists, or concrete blocks between
slab reinforced concrete joists, over void or crawl space
soil
OPTION 2 Original floor B – timber (solid or timber-derived
product) decking on timber joists
raised floor
insulating quilt
Insulation options
slab
For floor A as options 1, 2 and 3 for solid floors,
soil
with similar thermal behaviour, and (Figure 2.2):
OPTION 3
Option 5: If access to crawl space permits, it

may be possible to apply insulation to the un-
slab derside of the floor, or lay it onto the ground or
rigid insulation oversite concrete.
blinding
soil For floor B – insulation, or; as option 2
OPTION 4
Option 6: Remove deck and apply rigid or

Figure 2.1 Insulation options for solid ground floors semi-rigid insulation between joists.
Cold bridging is tolerable due to relatively
high thermal resistance of timber. Thermal be-
For option 2, the heating pipes are located just haviour as lightweight.
beneath the decking in the surface of the rigid
insulation.This results in a rapid response emit- Underfloor heating or cooling
ter with a large surface area, which with suitable
controls can be very efficient. Heating pipes can be incorporated in the above
Underfloor heating with option 3 could be deck screed or insulation as in options 1 and 2.
achieved with a warm-air supply. Pipes can also be installed in the top surface of
Underfloor heating should never be installed the between-joist insulation in option 5.
without insulation from the ground.
Floors 29
insulation options 1, 2 & 3 Figure 2.2 Insulation options for

screed suspended ground floors
concrete or ceramic blocks
pre-cast concrete or
steel joists
Apart from the opportuni-

insulating quilt
ties offered for heating and
soil or oversite concrete cooling systems integrated
OPTION 5 with the floor structure, insu-
lating the floor can have a
considerable impact on the dy-
namic thermal response of the
insulation option 2 building.
timber or timber product deck The simple rule applies, that
insulation thermal mass in the floor only
timber joists affects the interior if it is cou-
pled to it. This means that
options that isolate the floor
soil
surface from the massive struc-
OPTION 6
tural slab (as in options 2 and
3) will change the thermal re-
sponse of the space, making it
2.3 Intermediate floors much quicker to respond to heat inputs.
This may be advantageous in responding
Although heat flows may occur due to temper- quickly to heating systems in intermittently oc-
ature differences between floors, these will be of cupied spaces, or disadvantageous in spaces that
far less significance than heat losses from the might receive large and irregular heat gains, such
building envelope. Thus, it will not be cost ef- as solar gains. The latter has implications for
fective to insulate intermediate floors, except in comfort, where a traditional paved solid floor
special circumstances, where it is known that sig- maintains a steady temperature well below peak
nificantly different temperatures will be daytime temperatures, encouraging both radia-
maintained. Options would be similar to sus- tive heat loss and temperature stratification, both
pended ground floors. welcome in warm conditions. Massive floors are
also effective at absorbing solar gains when the
2.4 Thermal response implications of floor sunpatch is located on the floor, thereby reduc-
insulation ing daytime overheating and increasing the
usefulness of the gains to reduce auxiliary heat-
Floor insulation reduces heat losses in the heating later in the day.
ing season and may also improve comfort by Option 1, although isolated from the original
reducing temperature stratification where cool structural slab, provides a significant amount of
air collects close to floor level. The impact of thermal mass, and this will behave similarly to
floor insulation on heat loss may be less than ex- the original non-insulated slab to fluctuations of
pected when applied to deep floor plans, due to a diurnal frequency, but will not show the long-
the relatively low effective U-value of the non- term stability associated with thick slabs in
insulated floor away from the perimeter. ground contact.
Walls
3
Wall insulation is important for: 3.1 Solid walls
• heat retention in cool conditions; Here we refer to solid walls constructed of

• heat exclusion in warm conditions; bricks, stone, concrete block or in situ concrete.
• preventing the ingress of solar gains made by Other materials that might be encountered in
the absorption of radiation on the outside of historic buildings could include materials such
the opaque wall. as rammed earth (cob or adobe), and timber
framed walls with solid infill of mud, clay, soil
In non-extreme climates, due to the seasonal composites, often reinforced with light timber
variation, all of these conditions will be encoun- sections (e.g. wattle and daub). These kinds of
tered during the year.This means that in general, constructions often present problems for refur-
wall insulation will always bring positive benefits. bishment due to damp ingress and decay.
There may be some situations, however, where Solutions are highly specific to the technical de-
benefits may small in comparison with the cost, tails of the construction, and are not dealt with
or present technical difficulty and/or unaccept- here.
able visual impact.This is sometimes the case in The U-value of the non-insulated wall is of
historic buildings. Or there may be buildings course dependent on the material and thickness
where due to high internal gains, the lack of of construction.Typical values range from 1.0 to
need of close temperature control or the nature 3.0, which fall a long way short of current new-
of the activity, heating and cooling loads are al- build values.
ready modest.
There may also be some circumstances where External insulation (Figure 3.1)
overheating is made worse. This can occur in
buildings with high internal gains in cool cli- Option 1: Rigid insulation material fixed to
mates, particularly in lightweight buildings, or if wall and render applied.
the insulation is positioned on the inside of
envelope. However, except in rare occasions Option 2: Framing fixed to wall to create voids
where consistently high internal gains are pres- for non-structural insulation, render applied on
ent – for example, due to a manufacturing support layer (e.g. metal lath).
process – insulation will provide a better annual
performance, and overheating can be addressed Option 3:As above but with rigid cladding ap-
by proper ventilation and gains control. This is plied (e.g. timber, metal panel).
demonstrated in section 1.6, p8.
Option 4: Composite engineered cladding
panel providing weathering, insulation and struc-
tural support.
32 Practice
OUTSIDE INSIDE
solid wall framing
rigid insulation
insulation
render breather membrane
fastening
cladding
OPTION 1 OPTION 3
framing
metal lath
engineered panel
semi-rigid insulation or quilt including insulation
render structural framing

OPTION 2 OPTION 4
Figure 3.1 Options for external insulation of solid walls
Implications for external insulation In most cases, externally applied insulation elim-
inates cold bridges and (unlike internal
All forms of external insulation can be applied insulation) does not create new cold bridges.The
without changing the thermal response of the exception to this is where a balcony or other
interior.This is because the thermal mass of the structure will protrude through the insulating
structure remains coupled to the interior, which
is where the gains are made
(solar gains through windows
or gains from internal equip-
ment and occupants) (Figure
3.2).
External insulation also
protects the structure from
solar gains made on the ex-
ternal surface of the building.
These are important consid-
erations as both can reduce
the need for air-conditioning.
Finally, external insulation
may be part of a treatment to
provide new weatherproofing
to a degraded wall. Figure 3.2 Coupling of thermal mass with room interior
Walls 33
layer.This may not be easy to solve without re- Option 5: Rigid insulation material fixed to
constructing the attachment with a high wall and render or plasterboard applied. Plaster-
strength, low cross section element. board with integral insulation is available.
Non-thermal advantages include the benefit
Option 6: Framing fixed to wall to create voids
of work being able to be carried out without
for non-structural insulation, plasterboard or
disturbing the interior, and possibly allowing oc-
other cladding panel.
cupation to continue.
External cladding may cause a major visual However, option 4 will rarely find application –
impact. For some historic buildings this will be one fundamental difference being that the final
unacceptable. In cases where buildings are al- internal finish does not have to be a weathering
ready of rendered finish, using options 1 or 2 finish.
could leave the building with no significant
change of appearance. However, applying exter-
Thermal response
nal insulation to facades that are articulated and
have openings for windows etc., will be technic- The thermal response of the interior is changed
ally challenging. since the thermal mass of the original structure
In other cases, change of appearance may be is now isolated from the interior (see Figure 3.2).
welcome, and options 3 and 4 are often used to This will have most impact in smaller buildings
give visual as well as thermal improvement. where a greater proportion of the walls of the
rooms is external wall.Where a large building is
highly subdivided by partitions, if these are
Internal insulation (Figure 3.3)
heavyweight construction, and if further mass is
The constructional options for internal insula- present and accessible in the floor and ceiling,
tion are similar in principle to external the effect of insulating the external wall will be
insulation. slight. It is difficult to make quantitative rules,
and these issues should be investigated by ther-
OUTSIDE INSIDE
mal simulation.
rigid closed cell insulation

Cold bridges
special fastening or
Cold bridges will be created where internal parti-
adhesive tions and floors meet the external wall (Figure 3.4).
If, as is usual, they are of conductive materials, such
as masonry or concrete, this is a difficult problem
OPTION 5
to overcome. The solution necessitates bringing
the insulation back for a distance from the exter-
nal wall or floor (Figure 3.5) which in itself causes
framing problems particularly in the case of the floor.
insulation Cold bridges lead to increased heat loss, since
vapour check the average U-value of the envelope is increased.
plasterboard or
However, in walls, this effect may be relatively
other cladding panel slight, and could in principle be compensated by
extra insulation.The greater importance of cold
OPTION 6
bridges is that they lead to lower surface tem-
peratures and may become sites for surface
Figure 3.3 Options for internal insulation of solid walls condensation. This is particularly prevalent in
34 Practice
Interstitial condensation
OUT IN Internally applied insulation has the potential for
creating interstitial condensation – that is, conden-
sation occurring inside the structure. This can
low surface
temperature have a very damaging effect on the structure,
causing corrosion and decay, and in some cases
reducing the effectiveness of the insulation.
The cause of interstitial condensation is illus-
cantilevered trated in Figure 3.6. It shows that the diffusion of
balcony water vapour through the structure to a part
which is at a temperature below the dewpoint1
of the air. The solution is simple in principle –
Figure 3.4 Cold bridges left by external insulation
prevent the vapour from diffusing through the
material by applying a vapour check barrier to
the warm side of the insulation.
housing, or in other building uses with high oc-
cupancy and moisture production. OUTSIDE INSIDE
However, not all cold bridges have equal ther-
mal impact, and in some circumstances may be temperature
acceptable.The actual heat loss and resulting de- dewpoint
pression of surface temperature can be calculated
from the geometry and material properties of the condensation zone
bridge, using three-dimensional heat flow ana-

lysis. This could be worthwhile in a large project
where the elimination of cold bridges could be
very expensive.
temperature
OUT IN dewpoint
heat loss through gap vapour barrier

in insulation lowers
surface temp. here:
if surface temp. below
dewpoint, condensation
occurs
partition or floor
Figure 3.6 Interstitial condensation in wall without vapour
check and effect of vapour check on dewpoint profile
solved by insulation, but inconvenient

In practice it is not simple and two difficulties
arise. Firstly it is difficult to ensure that the
Figure 3.5 Insulating a cold bridge will be costly and vapour check is unperforated and sealed to such
inconvenient as door linings. Secondly, pressure differences
1 As a given mass of air is cooled down it can hold less and less water as vapour.The dewpoint is the temperature at
which it has a relative humidity of 100 per cent and further reduction of temperature will result in condensation.
R
Walls 35
OUTSIDE INSIDE As with cold bridges, there are not simple

rules, and a dynamic analysis of condensation
risk, considering the evolutions of temperature
masonry cavity
and humidity in the structure, should be carried
out for larger projects. In making this analysis,
practical difficulties of installing vapour checks
must be taken into account.
3.2 Cavity walls

Walls built from about 1950 onwards usually in-
cluded a cavity. In walls of double leaf masonry
in situ concrete (brick, concrete, stone, etc.) the main purpose of
external cladding the cavity was to prevent the transmission of
moisture from the outer leaf to the inner leaf.
The cavity also increased the thermal resistance
compared with the same amount of solid mater-
ial, but not sufficiently to meet modern
standards. For example, a 225mm solid wall has
a U-value of 2.3W/m2°K, whilst a cavity wall
with two leaves of 112mm has a U-value of
in situ concrete 1.7W/m2°K.This is still at least five times higher
internal cladding than typical newbuild values.
Composite walls may have cavities inherent
in their construction. For example, in situ con-
crete walls may have a cladding hung on steel
rails fixed to the concrete, creating a cavity be-
tween the cladding and structural wall.Walls with
a solid external leaf may be ‘dry lined’ with plas-
terboard or timber composite supported on
framed battens fixed to the structural wall.
Lightweight walls that are composed of ex-
ternal cladding panels and internal ‘dry lining’
supported on steel, concrete or timber frame will
also have a cavity, usually enclosing the structural
frame.
Insulation options
Figure 3.7 Typical cavity wall constructions
The insulation value of the cavity is dependent
on the ventilation and air movement. If the cav-
across the building envelope (due to wind or ity is freely ventilated to the outside – for
temperature differences) can cause bulk flow example, as in ‘rain-screen cladding’ – the insu-
(non-diffusive) of air via voids, conducting moist lation value of the cavity is virtually zero. The
air to cold sites. This is likely to be of much more restricted the ventilation, the greater the
greater magnitude than diffusive flow. insulation value, as the temperature in the cavity
36 Practice
and there is concern that the moisture-isolating

function of the cavity will be lost.The nature of
the climate, the degree of exposure of the build-
heat transfer
by radiation ing to driven rain, and the condition of the outer
leaf all have to be considered for the particular
project, and specialist knowledge sought.
heat transfer It is relevant to point out that in newbuild
by convection masonry cavity construction, it is normal prac-
tice to fix semi-rigid insulation to the inner leaf
and leave a cavity of at least 25mm between the
Figure 3.8 Heat transfer across a wall cavity by convection
insulation and the outer leaf.
and long-wave radiation
Composite and lightweight walls
It is less common practice to inject walls of this
increases. However, even for a non-ventilated type with loose fill, although if the outer leaf is
cavity, the insulation value is limited by the trans- reliably waterproof, and the conditions relating
fer by convection and radiation of heat from one to interstitial condensation (see below) are satis-
leaf to the other, as in Figure 3.8. fied, then there is no reason, in principle, why it
Improvement in insulation value can be made should not be done.
in two ways: The refurbishment of this wall type may in-
volve the stripping of either the inner or outer
1 Reducing the radiative transfer by includ- leaf. Provided the cavity is large enough this will
ing low-emissive surfaces. give the opportunity to fix semi-rigid insulation,
2 Reducing or eliminating convective trans- still maintaining a cavity.
fer by filling the cavity with insulating
material.
Interstitial condensation
Note that these are alternatives; there is no ad- The principle of interstitial condensation con-
vantage using low-e surfaces if the cavity is full, trol is to keep the temperature gradient (from
since heat transfer is now entirely by conduction. inside to outside) above the dewpoint gradient.
This can be achieved by vapour check mem-
Practical considerations branes as already discussed, and illustrated in
Figure 3.6.
Clearly the incorporation of a vapour check
Masonry walls
membrane is not possible in existing masonry
In the case of double masonry walls, it is usually cavities.When a cavity is insulated, the inner leaf
impractical to remove one leaf in order to place is usually sufficiently impermeable to water
rigid insulation in the cavity.Thus the cavity can vapour to ensure that the temperature in the in-
only be considered as a location for insulation if sulation does not drop below the dewpoint, as in
material can be injected or blown into the cav- Figure 3.9. Note that the drop of dewpoint in
ity via small openings. This is now a common an element is dependent on its relative resistance
practice, particularly in domestic buildings, using to vapour compared with the other layers. How-
materials such as rockwool, glass fibre and ex- ever, there could be combinations of a very
panded polystyrene beads. Other materials permeable inner leaf with an impermeable outer
include recycled cellulose fibre and vermiculite. leaf – for example dense concrete or granite –
With this technique, the cavity becomes filled, where condensation could occur on the inside
Walls 37
of the outer leaf.This would be a particular con- Where the problems associated with filling
cern if a biodegradable material such as the cavity cannot be overcome, external or in-
reclaimed cellulose fibre were to be used. The ternal insulation could be applied. The thermal
situation could be improved by rendering the implications of this action would then become
inner leaf more impermeable to vapour by sur- the same as the case of the solid wall.
face treatment such as paint.
Thermal implications
The principles of the change in thermal response
when applying insulation are the same as de-
temperature scribed for solid walls. If existing mass is isolated
dewpoint from the room, by the insulation, then thermal
response time will be reduced according to the
proportion of room surface treated.
In a double leaf masonry construction, most
of the active thermal mass is in the inner leaf and
so filling the cavity will have very little effect on
the thermal response.
Figure 3.9 Temperature and dewpoint profiles in masonry The only point to add is that if insulation is
wall with insulated cavity added to a lightweight wall, there will be no
change to the thermal response other than re-
duced heat loss.
In composite and lightweight walls, the situation
is similar to the case described for internal insu-
Retrofit inner or outer leaf
lation of solid walls. The risk of interstitial
condensation will often rule out the retro filling During refurbishment of ancient or historic
of the cavity unless the inner leaf is known to buildings there may be the need to build an
have a much higher vapour resistance than the inner leaf, on its own foundations, in order to
outer leaf. This is definitely not the case where provide structural support to upper floors, or to
the inner leaf is a dry lining such as gypsum plas- the existing external wall. If a cavity is to be in-
terboard, or where internal panelling has joints cluded, then, in principle, this could be insulated.
through which there could be bulk air flow. In However, it is possible that the requirements for
these cases, the only solution for cavity insula- bonding the new leaf to the existing wall may
tion would be to strip off the inner cladding and require the cavity to be too small for significant
install a vapour check, or replace the cladding insulation to be included. In these cases, other
with an inherently vapour resistive material such insulation options for solid walls will have to be
as polyurethane foam. adopted.
Roofs
4
Roofs include a wide range of construction Roof types
types and thus refurbishment solutions tend to
be very specific. Clearly a vital function of roofs The categories below have been chosen to re-
is the exclusion of water, and refurbishment is late to opportunities for insulation:
often driven by this.When this leads to re-roof-
ing, that is, replacing the whole weathering 1 roofs with accessible attic spaces (double
element, several options for thermal improve- pitched, mono-pitched or flat);
ment will present themselves. 2 roofs with voids;
In other situations, the weathering function 3 solid roofs.
of the roof may be perfectly satisfactory, and the
intervention may be to improve the thermal per-
formance only. In this instance a more careful
appraisal of benefit will have to be made and cost
effective options may be more limited.
Roof insulation is important for two main attic space
reasons:
traditional pitched
1 A poorly insulated roof can be a source of

large heat losses due to its exposure to
wind, the large convective transfer from a
warm surface upwards, and high radiant
losses to the night sky.
2 The roof surface receives the greatest inso-
lation during the summer period – solar void timber deck
gains conducted through the roof can be a
major cause of overheating and possibly
expensive mitigation by air-conditioning.
However, it has to be borne in mind that im-

provements to the roof will only have significant solid
benefit to the floor below.Thus the overall im-

waffle slab
pact of roof improvements will be quite different
for, say, a single-storey building and an eight-
storey building.
Figure 4.1 Types of roof
40 Practice
4.1 Insulating roofs with attic spaces In practice, this may not be possible at all times
because the temperature of the external roof
These give access to the upper surface of the element may drop below air temperature due to
ceiling element, thereby allowing the placement radiant losses to the sky, particularly at night.
of non-rigid insulation material. Usually there is However this will be a transient effect, and any
no space limitation, thus large thicknesses of in- condensation will evaporate at a warmer part of
sulation can be accommodated and high the diurnal cycle, and be removed from the attic
standards of insulation achieved at low cost. For space if there is sufficient ventilation.
example, the application of 300mm of fibreglass It is difficult to give simple rules on area of
to an uninsulated plaster ceiling under a tiled ventilation openings since there are unknown
roof will reduce the U-value from 2.5 W/m2°K variables such as the humidity in the building
to 0.1 W/m2°K, a factor of 25 times. and the vapour permeability of the ceiling. In
some cases, attic ventilation provision is governed
Ventilation of attic space by building codes. However, as an approximate
guide the total ventilation area should be be-
In traditional construction it is likely that the tween 0.3 and 1.0 per cent of the ceiling area,
ceiling will be lime or gypsum based plaster sup- well distributed in plan and vertically. Distribu-
ported on lath or plasterboard.These are vapour tion is important to encourage good mixing and
permeable. Many modern ceiling constructions stack effect ventilation on calm days.
are also permeable, due to gaps and joints, even Care should be taken to ensure that the insu-
if the material itself is not vapour permeable. lation material does not obstruct air flow at the
Since water vapour is generated in all occupied eaves, particularly when there are no other ven-
buildings, it is essential that the attic space, into tilation openings. As a general rule, it is much
which the water vapour will migrate by either safer to over-ventilate, since as the attic space is
diffusion or bulk flow, must be ventilated suffi- cold (all of the temperature drop is in the insu-
ciently to keep the dewpoint below the air lation), there is no energy penalty for
temperature and surface temperature. over-ventilation.
4.2 Insulating roofs with voids

This will commonly apply to flat roofs. It will
also apply to pitched roof attics that are to be oc-
cupied, where the insulation must be in the
plane of the outer roof element.
If the void is to be used as the location for in-
sulation, the main problem is interstitial
condensation, as described for walls in section 3.1,
p34. The problem is exacerbated for flat roofs,
since the horizontal outer element (typically bitu-
men, lead or a rubber/plastic based membrane)
has to be inherently waterproof and thus highly
resistant to vapour.This rules out the filling of a
roof void with particulate insulation (e.g. mineral
fibre, polystyrene beads) by injection through
Figure 4.2 Migration of water vapour through ceiling and small openings, since it would be impossible to
insulation requires ventilation of attic space insert an internal vapour check between the ceil-
Roofs 41
ing and insulation. Furthermore, unless the void In both the above cases, the recommendation
is unusually large and only partially filled, suffi- is to gain complete access to the void by the re-
cient ventilation will be very difficult to provide moval of either the inner or outer elements, and
passively. install a vapour check membrane on the warm
side of the insulation.The technical details of in-
stallation are not dealt with here, but it is essential
that it is carried out with a high standard of
workmanship and supervision.
Insulation materials can be highly vapour per-
meable – such as mineral wool or cellulose fibre
– or inherently impermeable, such as closed cell
polystyrene or urethane foam. Closed cell foams
will not suffer interstitial condensation within
their volume. However bulk flow of air can take
place between slabs of insulation and conduct
moist air to cold parts of the structure – thus a
vapour check is still essential. It is also strongly rec-
ommended that the void is not filled, leaving a
space above the insulation that can be ventilated.
There can be no short cuts to this problem.
There have been cases of total structural failure
due to interstitial condensation.
4.3 Insulating solid roofs (or roofs with

inaccessible voids)
For flat roofs three options are available:
1 insulation above the waterproof mem-

Figure 4.3 Dewpoint profiles in insulated flat roof with brane;
and without vapour check and roof ventilator 2 insulation between waterproof membrane
and structural deck;
3 insulation below the structural deck.
Where the inner and outer roof elements are
pitched – for example, a tiled roof over an attic
Insulation above the waterproof
room – the outer element has only to be water-
membrane
shedding rather than water-proof. Provided a
vapour-permeable membrane (or no membrane The so-called ‘upside-down’ roof relies on the
at all) has been used between the outer layer and inherent waterproof properties of closed-cell
the void, it might be possible to inject loose fill plastic or glass foam insulation. Slabs of rigid in-
insulation without a vapour barrier.The risk of sulation are cut to fit and simply laid on the
condensation will depend, as with ‘attic spaces’, existing waterproof membrane.They are usually
above, on the prevailing humidity in the heated weighted down with either concrete slabs or
space, and the vapour permeability of the inner gravel.This method is particularly suited to con-
ceiling. However, the risk is high and it is not crete decks, where the extra loading due to the
recommended without careful analysis. gravel or slabs is unlikely to present problems.
42 Practice
gravel or concrete tiles
rigid insulation
drained waterproof membrane
from this (temperature stabilized)
level
structure
Figure 4.4 Insulation above the waterproof membrane; the ‘upside-down’ roof
The roof is drained at the membrane level. The disadvantage of the method is that the
The great advantage of this method is that the waterproof membrane remains exposed to the
waterproof membrane is protected from thermal weather. In the case of heavy concrete or ma-
stress and other damage, and kept at a very stable sonry based roofs, the waterproof membrane will
temperature. The work can also be carried out experience much greater temperatures and tem-
with no disturbance to the interior, and because perature gradients due to the isolation of the
the waterproof membrane also acts as a vapour membrane from the thermal mass of the struc-
check, and is on the warm side of the insulation, ture. This can develop shear stresses along
there is zero risk of interstitial condensation. shadow lines and at the edges of puddles that, to-
A further advantage is that most cold bridges gether with the effects of UV, can accelerate the
(see section 4.4) will be avoided, although some ageing and failure of the membrane. On roofs
problems may be encountered where there are with lightweight decks, the difference will be less
parapet walls. marked, although even the thermal capacity of
timber will have some moderating effect.
Thus wherever possible, it is recommended
Insulation between waterproof membrane
that option 1 is adopted.The only exception to
and structural deck
this might be where on a historic building part
This might be carried out on a roof that had to of a flat or low-pitched roof is covered with lead
be stripped due to the poor condition of the or copper, and a change of appearance is unac-
waterproof membrane. ceptable.
waterproof membrane
(temperature unstable)
high surface temperature
insulation
vapour check
Figure 4.5 Insulation between
deck and waterproof membrane
leading to high thermal stresses
Roofs 43
Insulation below the structural deck 4.4 Other thermal issues

This will almost always involve the erection of a
secondary supporting structure (i.e. ceiling), and Surface reflectance
thus the issues become the same as for existing In warm climates where solar gains through the
roofs with voids.The main concern is the avoid- opaque fabric of the roof are a problem, the ther-
ance of interstitial condensation by preventing mal performance of a roof can be greatly
moist air from the interior getting to the cold influenced by increasing the reflectance of the
underside of the structural deck. This can be roof surface. It is common practice in tropical
achieved (but not without difficulty) by using a areas, where for traditional buildings the roof U-
vapour-check membrane and ventilation as de- value is usually quite high.
scribed in section 4.2. The penetration of solar gains made on the
temperature moderately stable
ventilation space
insulation
vapour check
ceiling
Figure 4.6 Internally insulated solid roof outer surface of a roof construction is described
by the Solar Heat Gain Factor (SHF).Table 4.1
shows the effect of changes of reflectance by sim-
ple low cost means.
An exception to this is where an inherently
vapour proof material is fixed to the underside of
the deck. This is sometimes achieved by spray- Table 4.1 Solar Heat Gain Factors (SHF) for various
ing with an expanding polyurethane foam. constructions and finishes
Lightweight renders with cellulose fibres and Roof construction Solar heat U-value
other mineral fibres are also used. However, due gain factor W/m2°K
to the vapour permeability of the render, the %
possibility of interstitial condensation must be
much higher. (1) Non-insulated dark coloured
This method has also been used on light- steel corrugated sheet with ceiling 7.6 1.9
weight pitched roofs made of a single element (2) as (1) with 50mm fibreglass 5.2 1.4
such as corrugated iron (or other metal), or even
tiles. It is often regarded as a short-term solution, (3) as (1) whitewashed ext. 3.7 1.9
particularly in the latter case. The implications (4) 150mm concrete slab 9.1 3.3
for materials such as polyurethane for the in-
staller’s health and the environment generally (5) as (4) with 50mm fibreglass inside 3.1 0.6
should be considered. (5) as (4) whitewashed ext. 4.1 3.3
Source: Koenigsberger, O. and Lynn, R. (1965) Roofs in the Warm Humid
Tropics, Architectural Association, London
44 Practice
When not dictated by the materials and in

cases where overheating is the main problem, the
use of high reflectance surface treatment is al-
ways recommended. Not only does it reduce
transmitted solar gains, but also the surface suffers
transmitted solar gain
less from degradation due to high surface tem-
peratures. Finally, in urban environments, the
higher the urban reflectance (albedo), the less the
urban heat island effect.
Low-emissivity membranes in cavities

Figure 4.7 shows the effect of improving the per-
formance of a roof by reducing the transmission
aluminium by radiation across the roof cavity or attic space
reduces emitted radiation foil on
upper by the use of low-emissivity membranes such as
surface
aluminium foil or aluminium-coated plastic.This
could be a low cost measure where the roof
space is accessible, but becomes increasingly less
effective when the roof is insulated conductively.
It is important to note that reflective mem-
reflects back radiation branes are only effective in reducing transmission
aluminium
foil on lower by radiation, and therefore only have any bene-
surface ficial effect when facing a cavity.They should not
be used by laying them on top of insulation un-
Figure 4.7 Transmission of solar gain through non- less they are of the breather variety. Impervious
insulated horizontal roof void and effect of low-emissivity membranes would be likely to cause interstitial
surface (aluminium foil) on upper and lower surface of the condensation.
cavity
Thermal mass
Most paints that are optically white – that is, they The issues are much the same as with wall insu-
reflect nearly all visible radiation – still absorb lation – that is, the effect of internal insulation is
the near infrared (IR), which forms nearly half of to isolate the thermal mass from the space and
the energy in the solar spectrum. New paints that therefore remove the generally beneficial effect
are reflective to the near IR are becoming avail- of reducing peak temperatures.
able, and even when coloured (i.e. absorbing This makes the externally placed roof insula-
some part of the visible spectrum) their per- tion (either above or below the waterproof
formance is still better than conventional white membrane) doubly beneficial since it not only
paint. provides thermal mass to the interior to absorb
Polished metallic surfaces also have low IR daytime gains, but also protects the structure
absorption. However, they have poor emissivity from daytime solar gains that would otherwise
in the long-wave IR, thus reducing the loss of be transmitted into the interior in the evening
heat at night. Conventional non-metallic paints or night.
have good long-wave emissivity.
Roofs 45
Cold bridges ment of cold bridges has been dealt with in some
detail in Chapter 3,‘Walls’, and the principles are
Cold bridges are areas where structural (or other much the same.
components of non-insulating material) prevent
the application of insulation.Typically these will
be beams or joists, where insulation is placed in 4.5 Green roofs and roof ponds
the space between them. The effects and treat-
Green roofs
evap. cooling from soil and transpiration
Green roofs consist of a layer of soil or turf which
supports growing vegetation. Flat or low pitched
roofs are the commonest in new building, al-
soil and
though steeper pitched roofs can be engineered,
grass and are actually more common in vernacular ex-
amples.
Contrary to what is often claimed, turf (soil
poor and vegetation) is not good thermal insulation
insulation
compared to modern insulation materials, as il-
evap. cooling lustrated in Table 4.2. If it is wet – that is, in a
condition to support growth – it is very poor.
The only thermal benefit a turf roof could bring
is in the provision of thermal mass. However, for
buildings that are heated, thermal mass without
thermal insulation is not beneficial over the year, and
mass
once insulation is added (obviously it has to be
very poor on the inside), the benefit of the thermal mass is
insulation
largely lost.
In a warm climate, where the mean temper-
Figure 4.8 Green roofs and roof ponds add thermal mass ature is somewhere near comfort temperature,
and evaporative cooling to the roof but do not in non-insulated thermal mass may be beneficial,
themselves provide significant insulation especially in the roof, which receives the largest
Table 4.2 Properties of materials for green roofs compared with conventional materials
Material Conductivity Density Load (W/m2°K)kg/m2

W/m°K kg/m 3
for U = 1.0
wet soil 1.2 1900 2280
dry soil 0.55 1500 825
dense conc 1.6 2200 352
lightweight conc 0.4 1200 480
wood 0.125 610 76

rockwool 0.036 50 1.8
46 Practice
solar impact, although it is likely that insulation capacity of water and its fluidity). Although it
would still be the better option.A further bene- also provides evaporative cooling, less evapora-
fit may be gained by evaporative cooling, tion takes place from free water surface than by
provided there is a source of water for replenish- transpiration from the leaves of vegetation.
ment. The water surface is exposed to the cold night
If being considered for retrofit, the major sky, which can have an effective radiant temper-
non-thermal consideration is whether the struc- ature of 10° to 15°K lower than air temperature.
ture can take the extra load. This will rule out The water surface has high emissivity and loses
the option for many lightweight constructions, heat, which mixes efficiently due to downward
which unfortunately, stand to gain most. On the convection.This cooled water can then be used
positive side, the green roof can be seen as a re- passively, by absorbing heat conducted through
placement for the original vegetation that the the ceiling, or actively by a pumped circulation
building replaced, and in urban areas could pro- to suitable emitters.
vide a valued recreational area, as well as The roof pond enjoyed some fame in the US
contributing to CO2 absorption. in the 1970s, with Harold Hay’s Skytherm.
However, one important difference is that Moveable insulation protected the pond from
natural vegetation has access to ground water, solar gains in the day, when the passive conduc-
whereas green roofs will have to have pumped tion of gains from within were absorbed by the
water supplies due to the intermittency of sup- cool water.
ply from rain, and limited storage capacity of the Similar to the green roof, an important non-
turf. thermal consideration is the structural support.
This may already be sufficient for short spans, but
for large spans could involve extra investment in
Roof ponds
structural materials. Furthermore, parasitic en-
The roof pond is thermally one step further than ergy used for pumping and other mechanical
the green roof, providing a larger and more re- operations must be evaluated.
sponsive thermal mass (due to the high thermal
Windows
5
Windows are the most energy-transmissive elem-
ents in the envelope. Even the highest
performance glazing has a U-value at least five
times greater than typical insulated opaque elem-
ents. When in direct sun, windows will transmit
around 400W/m2, 40 times greater than a 20°C
temperature difference across a wall with a U-
value of 0.5W/m2. As well as this, windows
provide useful daylight that can reduce the de-
pendence on artificial light, one of the main
energy consumers in non-domestic buildings.
It is not surprising then, that windows and
glazing have a crucial effect on building per-
formance. Refurbishment provides the
opportunity to incorporate the latest technology
for glazing materials and framing components as
well as adding to the ‘daylight system’ in the form
of shading and reflecting elements.
5.1 Glazing materials

The key characteristics of glazing are the thermal
transmittance (U-value) and the optical trans-
mittance. It is the combination of these that Figure 5.1 LT Curves (annual energy consumption as a
affect the performance of glazing in admitting function of glazing area) for different glazing types showing
visible daylight (and allowing views out), and at the effect on optimum glazing area
the same time keeping the heat in, or in over-
heated climates, out. The balance of these two
characteristics should influence the designed
The physics of the energy balance of glazing is a
glazing area; increasing the area admits more
little more complex than two characteristics
light, thus reducing the need for electric light,
alone might suggest, since heat transfer involves
but increases the heat transmission. It follows that
radiation as well as conduction and convection,
the area that gives the optimum energy per-
and the transmission of radiation has a bearing
formance is dependent on the value of these two
on thermal solar gain as well as useful daylight.
key parameters.
48 Practice
Heat transmission through glazing The surface of the glass presents a resistance to
the convective component (in Figure 5.2) due
Figure 5.2 shows separately the processes in- to the stationary layer of air a few millimetres
volved in the transmission of heat and light thick that acts as an insulator. This resistance is
through single glazing. Both are present simul- known as the surface resistance (or inversely, the
taneously. surface conductance), and for still indoor air is
about 0.123m2°K/W.1 The standard value taken
OUTSIDE INSIDE for outside is lower, due to the prevalence of air
movement, and is usually taken as 0.05.The re-
sistance of the glass itself is very small, about
long-wave long-wave 0.004 for 4mm glass.
re-radiation The U-value is given by the inverse of the
total resistance:
1/0.177 = 5.6W/m2°K
It is important to note that the majority of the

thermal resistance of single glazing is due to the
surface layer surface layers. If this layer is eroded by internal air
movement induced by fans or convection,
conduction
and/or the outer layer is reduced by wind, the
overall U-value of single glazing could be in-
R = 0.05 + 0.123 + 0.004 = 0.177 creased by a factor of two. A simple explanation
U = 1/R = 5.6 of double glazing is that a further two still air lay-
ers are included. However, heat transfer between
the two leaves still takes place by radiation re-
Figure 5.2 The mechanisms of energy transfer through
sulting in the U-value being reduced to only
glazing by convection and conduction
Table 5.1 Typical U-values for different glazing specifications

Glazing type U-value Light transmittance Total transmittance
single 5.4 0.87 0.90

double 2.8 0.76 0.82
triple 1.9 0.65 0.74
double low-e 1.8 0.64 0.58
double low-e inert gas 1.5 0.64 0.58
double tinted 2.8 0.35–0.65 0.65–0.75
double reflective 2.8 0.15–0.3 0.2–0.38
double low-e high performance 1.5 0.25–0.5 0.3–0.45
1 This includes an effective resistance to take account of radiative transfer from room surfaces to the glass.
Windows 49
1400
solar radiation in W/m2/micron
transmission coefficient
Figure 5.3 The
spectrum of daylight
1200
and the transmission
coefficient of various
1000 glasses
800
incident
600
spectral transmission of glass
400
200
transmitted
0 0.4 0.6 0.8 1.0 1.2 1.4 1.6 1.8 2.0 2.2
visible wavelength in microns
about 3W/m2°K. Note that increasing the gap transfer by radiation.This is achieved by coating
between the panes beyond about 16mm does the surface of the inner leaf that faces the cavity
not reduce the U-value further since convection with a low-emissivity coating.This very thin (less
currents are set up, transferring heat from one than a wavelength of light) metallic layer trans-
surface layer to the other. mits short wavelengths (i.e. visible light) but acts
The next step to reduce losses is to reduce the as a poor emitter for long-wave infrared (IR).
OUTSIDE INSIDE
incident
radiation
15% 80% 15% 25% 70% 25%

reflected transmitted
5% absorbed 60% 5%
CLEAR TINTED REFLECTIVE
Figure 5.4 The transmission of energy by short-wave radiation through clear, tinted and reflective glass
50 Practice
This typically reduces the U-value to about cannot then be re-radiated as long-wave IR re-
2.2W/m2°K. sulting from the warming of the room’s contents.
Finally, the convective transfer can be reduced Two other types of glass are commonly en-
further by reducing the conductivity of the gas countered: tinted and reflective (Figure 5.4).
in the cavity.This is achieved by replacing the air Tinted or absorptive glass contains pigments to
with a heavy inert gas such as argon, resulting in increase the absorption of visible and near IR.
the U-value dropping to about 1.8W/ m2°K. This reduces the transmittance, typically from 40
U-values can be further reduced by triple per cent to as low as 10 per cent.The absorbed
panes and multiple coatings. Table 5.1 summa- energy heats up the glass and this heat is partly
rizes typical U-values for different glazing conveyed into the room and partly to the outside
specifications. by radiation and convection. It is not a good so-
lution to overheating due to excessive solar gain.
Reflective glass has a thin metallic or semi-
Radiation transmission through glazing
conducting coating that increases the reflected
Rather less than half the energy in daylight lies component, also reducing the transmission.
in the visible spectrum (Figure 5.3). Most of the However, in this case, the energy is reflected
remainder is in the infrared (IR) region and a away from the glass, not absorbed by it, and thus
small fraction in the ultraviolet (UV). Only the causes no heat gains to the room.
visible component is useful for daylighting.
However both components are transmitted by
High performance glazing
glass and thus contribute to unwanted overheat-
ing and useful solar gain when absorbed by Glasses that are referred to as ‘high performance’
surfaces in the room. have the important property that the transmit-
Figure 5.4 shows the energy balance of the tance in the invisible spectrum (the infrared and
radiation incident on the glazing.The radiation the ultraviolet) is significantly reduced.Although
falling on the glazing surface becomes three the thermal gains due to the absorption of the
components – a reflected component Ir, a trans- visible light remain the same (for a given level of
mitted component It and an absorbed illuminance), gains from the invisible part of the
component Ia. For normal clear glazing, in the spectrum are reduced.Thus the light can be re-
visible region the reflected component is about garded as ‘cooler’, or put more scientifically, to
15 per cent of the incident value but this in- be of higher luminous efficacy.
creases strongly when the angle of incidence This is illustrated in Figure 5.5 which shows
increases beyond about 60°. The transmitted the heat gains to a 12m2 room for different glaz-
component is about 80 per cent of the incident ing materials. In each case, the area of glazing is
radiation, leaving 5 per cent absorbed by the adjusted to give an average illuminance of 300
glazing. lux.This is also illustrated in Figure 5.6.The x-
The proportion of transmitted, reflected and axis shows the ratio of total transmittance Tt to
absorbed radiation varies according to wave- the visible transmittance Tv. For high perform-
length, as indicated in Figure 5.3. Only a small ance glass, the ratio Tt/Tv is less than one.
fraction of UV light is transmitted. Roughly 80 However, even if none of the invisible radiation
per cent of the visible spectrum is transmitted by were transmitted, this ratio could not be below
glass (e.g. 4mm window glass) in the visible spec- about 0.5, since about half of the thermal effect
trum, and about 70 per cent in the near IR of solar radiation is due to visible radiation.This
region. Far IR radiation is absorbed – this leads is shown as the theoretical limit on the graph.
to the ‘greenhouse effect’ where energy admitted Materials with ratios greater than one actually
as short-wave IR and visible, converted into heat, worsen the situation, since, as the graph shows,
Windows 51
clear glass
Heat gain for 300 lux over 12m2

3.2m2
bronze absorbing
VIS VIS Tv = 0.87

INV Tt = 0.95
750W/m2
total heat gain 2.2kw
green absorbing
blue reflecting
unglazed aperture
clear glass
7.1m2 tinted glass green high performance
theoretical
VIS VIS limit
Tv = 0.39
INV Tt = 0.69
1 2 3
750W/m2 Tt / Tv
increased luminous reduced luminous
efficiency efficiency
4.9m2 high performance

Figure 5.6 Solar heat gain plotted against the ratio of
VIS VIS total transmittance to visible transmittance, for a given
Tv = 0.56
INV Tt = 0.48 average illuminance of 300 lux
750W/m2
5.2 Framing and support systems
Figure 5.5 Heat gains from solar radiation for different
As technology has advanced, larger and larger
glass types, adjusting glazing areas in order to keep the
sheets of glass are manufactured. In new build-
room illuminance constant
ings this has led to supporting systems that
minimize both visual and thermal impact. In
more heat is generated in the room for the same older buildings the reverse is true with the fram-
amount of light. ing of smaller panes of glass affecting the
Buildings that have encountered overheating appearance, the light transmission and the ther-
in the past may have had tinted glass or film mal conductance of the whole window element.
retrofitted at some stage. Since the absorbed en- An increase in the total glazing area has
ergy is partially transmitted to the room, the tended to follow growth in sheet size, which in
improvement may have been marginal. Refur- turn has demanded novel glazing support sys-
bishment is an opportunity to replace with clear tems, ultimately leading to the 100 per cent glass
glazing and/or shading devices reduce the glaz- facade. Curtain walling is the principle of sup-
ing area. porting glazing or other lightweight panels
Table 5.1 lists generic glazing types giving within in a lightweight frame, given lateral sup-
their U-value, light transmittance and total transport from the parent structure. In the last two
mittance. Some trade information gives the decades invisible fixing systems attaching to the
shading factor which is defined by shading factor backs of panels have developed, now making the
= 1 – TT. Note that the shading factor alone is 100 per cent glass facade possible.
not an indicator of performance as a window Before the development of high performance
material – for example, a brick wall has a shad- glass, these systems often led to grossly over-
ing factor of 100 per cent! glazed buildings suffering from excessive heat
52 Practice
Figure 5.7 The evolution of glass pane size: top left: 17th
century cottage Weald and Downland Museum, Sussex, UK;
bottom left: Georgian terraced houses in London; above:
100 per cent glazing in 1990s office block, Berlin
loss in winter, with glare and unwanted solar

gains in summer. These buildings are amongst
those now eligible for refurbishment and solu-
tions may well involve major intervention to the
glazing.
Obstruction of light due to framing

The obstruction of the framing and glazing sup-
port system is often greater than expected, as
illustrated in Figure 5.8.
The analysis here only considers the obstruc-
tion of the framing in the plane of the glazing.
Framing has a third dimension and this can also
have an effect on the transmission of the win-
dow at greater angles of incidence. For example,
a window in a narrow street may have a sky view
only at angles greater than 45–60°. Heavy mul-
lions and transom elements when seen projected
at such angles will obscure a greater area than
when viewed at right angles, and if they are fin-
ished in a dark colour, will seriously reduce the
daylight transmission.
Windows 53
because of the very high thermal conductance

of aluminium, at 237W/m°K it is 1500 times
greater than the thermal conductivity of wood.
10%
Nevertheless, the ability to extrude aluminium
with highly complex sections renders it ideal for
framing elements supporting glass panes and seals
for opening windows. (Modern window sections
25%
have partially overcome the problem of high
conductivity by introducing thermal breaks (in-
sulated sections) in the framing components.)
Unfortunately, windows of the design and
40%
material in the example above are relatively
common in buildings built in the last 50 years,
Figure 5.8 Obstruction due to framing and are now become candidates for refurbish-
ment. Clearly upgrading windows of this design
by replacing the glazing alone will not be suffi-
Refurbishment could offer an opportunity to cient in itself. In the example above, the
make improvements either by reducing the size aluminium framing increases the U-value by 70
of the framing elements or, where there is a sig- per cent. The same construction glazed with
nificant three-dimensional effect, increase the low-e argon-filled double glazing with a ‘mid-
reflectance. Both of these measures will have a pane’2 U-value of 1.6, would be increased to 4.8
visual impact to the elevation and may therefore by conduction via the aluminium mullions, an
be precluded for historic buildings. increase of 200 per cent.
There are three options available in this ex-
ample. The first option is to insulate the
Thermal performance of framing mullions, either inside or outside.This is labour
The framing of panes of glass can have a large intensive and may present problems due to
impact on the overall U-value of the glazing plus change of appearance. In our example, practical
frame. As with light transmission, it is a three- considerations limit the insulation thickness to
dimensional problem, not just the proportion of about 25mm; thicker than this begins to obstruct
the opening occupied by the frame in the plane the glazing significantly. However, this kind of
of the glass. Figure 5.9 shows a serious case glazing is often encountered in buildings that
where aluminium framing increases the U-value have more than sufficient glazing area, thus some
from 5.6W/°Cm2 to an average U-value of obstruction, though changing the appearance,
9.5W/°Cm2.This is due to the ‘fin effect’ – the will still leave adequate glazing area, particularly
fact that the internal and external surface areas of with a high reflectivity finish.
the mullion are the limiting conductance rather The second option is to install a secondary
than the cross section of the aluminium.This is glazed screen of high performance glazing and
Figure 5.9 Single glazing in aluminium

mullions: U-value increased from 5.6 to
single glazing aluminium mullion 9.5W/°Cm2 due to ‘fin effect’
2 U-value of pane away from the influence of framing element.

54 Practice
thermally insulated framing.This could be inside nearly as low as timber at 0.15W/m°C, both
or outside, and carries the advantage that it could orders of magnitude lower than aluminium at
form the main airtight layer, thus addressing a about 237W/m°C.
second problem of air-leakage commonly found UPVC also can be easily extruded into com-
in older glazing systems. If outside, the skin can plex sections and claims are made for its low
also form the weathering layer. maintenance and long life. However, it is vul-
The extreme application of this strategy is the nerable to UV degradation, losing its glossy
second skin as described in Chapter 9 and illus- surface and becoming brittle over time spans of
trated by the Albatros project in Figures 9.3 and 20 years or so. PVC windows also have much
9.4. Clearly secondary glazing will affect the ap- greater environmental impact than timber, due
pearance, either from inside, or outside, or as in to their embodied CO2, pollutants during manu-
the case of the Albatros, both.And there may be facturing and difficulty in recycling.
high costs, particularly associated with external Timber carries none of the above disadvan-
secondary glazing. tages, being almost carbon neutral. Good quality
The third option is to replace the glazing and timber, with good detailed design and mainten-
the framing system with high performance glaz- ance can last for a century or more. Many
ing and thermally insulated framing. This will historic buildings from the 19th century still
also involve high costs in both money terms and have their original window frames, where build-
embodied CO2. ing of 100 years later have already had one or
even two replacements.The reasons for this long
life the quality of the timber – often high-
Framing material
latitude grown resinous pine, spruce and fir, and
Other materials commonly used for framing sys- the detailed design which discouraged the har-
tems are UPVC and wood. The thermal bouring of water and migration of damp from
conductivity of UPVC is about 0.2W/m°C, masonry. Unfortunately, in an effort to ‘modern-
Table 5.2 U-value of glazing and framing combinations for pane size 1.2m x 1.2m. These values are indicative only. The full
procedure for calculating whole window U-values can be found in ISO 10077-1
Glazing + framing system U-value of glazing material U-value of glazing + framing
Double glazing 2.8 3.1

Aluminium
Double glazing 2.8 3.0
Aluminium with thermal break
Double glazing low-e inert gas 1.5 2.7
Aluminium
Aluminium with thermal break
Timber
Timber with thermal break
Windows 55
ize’ in style and production, many of these at- U-value can be significant. For example if the 70
tributes are missing in window design from the per cent double glazing of a facade is reduced to
1950s onwards. 35 per cent with an opaque material with U-
In spite of the long life of these early win- value of 0.2W/m2oK, the average U-value of the
dows, because they were predominantly single original aperture would be reduced from 2.16 to
glazed and were often poorly fitting, they pres- 1.18W/m2°K. If it was originally single glazed
ent problems in sustainable refurbishment. The and was reglazed with low-e of 35 per cent glaz-
insertion of double or triple glazed panes into ing ratio, the average U-value would be reduced
the slender wooden sections is virtually impos- from about 3.56 to 0.83.
sible. There are a number of products available
for improving airtightness, but these also have
some visual impact and it is difficult to achieve
the same performance as a modern window.
The recognized historic value of the building
will often set priorities here – in some cases tol-
erating the poor thermal performance and
seeking other ways to reduce the carbon emis-
sions of supply, by means such as combined heat
and power (CHP) or renewable heat sources. In
other cases, compromises may be possible such
as the installation of internal secondary glazing.
Table 5.2 summarizes the effect of framing on
the combined U-value of glazing and frame.
Note that it is sensitive to the proportion of Figure 5.10 The average U-value as a function of glazing
framing to the total area of opening in the insu- ratio
lated building envelope.
5.3 Modifying apertures Although 35 per cent glazing can be shown to

provide adequate daylighting for rooms of up to
Many buildings from the 1950s onwards, which 6m deep (for unobstructed windows), care has
are now being considered for refurbishment, to be taken with how the distribution of glazing
have large areas of glazing. In many cases this is is altered. General rules of thumb are for spaces
single glazing, and would thus be a possible can- with a 2.7–3m floor to ceiling height:
didate for glazing replacement. If aesthetic
considerations allow it, a reduction of the aper- • Cill heights should not be raised above 1m
ture area could be considered. This will have from floor level.
several advantages – reducing heat loss and un- • Glazing in the upper part of the wall is more
wanted solar gain, reducing glazing costs, effective than the lower.3
reducing shading costs, and in some cases sup- • Horizontal distance between glazed openings
porting interior remodelling by providing more should not exceed 3m.4
wall space for furnishings and equipment. • There may be a case for splitting the viewing
Since the new opaque envelope can have U- and daylighting function.
values as low as 0.2, the impact on the average
3 Except when there are deep overhangs.

4 Or 2m from a cross-wall in cellular offices.
56 Practice
There may be cases for increasing the glazed area,

where daylighting is demonstrably inadequate.
However, other causes for poor daylight per-
formance should be eliminated first – for
example, low transmission of glass, obstruction
due to framing or poorly designed fixed shading
devices, low reflectance of interior surfaces, or
internal obstructions.
There may be cases for changing the distri-
bution of glazing by making new apertures.
Single-storey buildings and top floors offer a
good opportunity for this. Small areas of
rooflighting over a deep plan can make a dra-
matic improvement in daylight distribution and,
therefore, the luminous efficacy of the system.
However, in warm climates, rooflights should
never be unshaded horizontal glazed apertures, Figure 5.11 The traditional louvred shutters on the south
but always structures with apertures sloping away facade retained as shading devices for the Meyer Hospital
from the equator. refurbishment, a REVIVAL project
5.4 Shading systems

the reflection of light from surfaces and/or the
The need for shading as part of any window sys- obstruction of light from specific directions,
tem is now widely recognized. Only in the era of some devices can improve the distribution of
cheap energy and immature modernism was daylight in a room.
shading regarded as an inconvenience and an aes- Side-lit rooms from plain apertures are very
thetic intrusion that could be dispensed with by unevenly lit, as shown in Figure 5.12.This means
the substitution of air-conditioning.The enthu- that in order that the minimum illuminance is
siasm for large areas of glazing and lightweight sufficient, the part of the room near to the win-
construction exacerbated the problem, which we dow has to be over-illuminated.At times of zero
have now inherited. heating load this over-illumination serves no
Vernacular architecture, with its rich tradition useful purpose, but will contribute to overheat-
of louvres, shutters, jaloises, overhangs and blinds ing and probably glare.
clearly demonstrates that, before this profligate If the light distribution can be improved, the
period, passive low-energy design had to include total amount of light flux entering the room
these elements. With global warming and the (and the invisible radiation accompanying it) can
gradual shift from the problem of heating to that be reduced. Thus the ideal shading device not
of cooling, the understanding and adoption of only modulates the transmittance of the window,
shading has become an essential part of sustain- compensating for conditions of high radiation
able refurbishment. levels, but also improves the efficiency of distri-
bution. Figure 5.12 shows how a light shelf
reduces illuminance close to the window more
Daylight redistribution
than at the back of the room.Thus, the unwanted
Shading devices have an important function part of the incident radiation is reflected away,
other than simply reducing the quantity of radi- reducing solar gain. Horizontal louvres can work
ation transmitted through the window. Due to in a similar way.
Windows 57
Figure 5.12 The daylight profile of

a side-lit room. A light shelf can
reduce the illumination close to the
window without reducing it at the
% DF 5
DF profile without lightshelf
back of the room, thereby increasing
the illumination efficiency
2
DF profile with lightshelf
0 Shading options for

refurbishment
6m 5 4 3 2 1
Some of the buildings where
the architectural specification
has not included shading pro-
vision will have had shading
solar radiation reflected
and absorbed
retrofitted at some stage. Most
commonly this will be inter-
nal curtains, blinds or louvres,
but at worst, pieces of paper
heat from absorption radiated stuck onto the glass by desper-
and convected away ate occupants.The installations
are often poorly integrated
Typical solar gain factor for with the window design,
external white louvres: 12%
obstructing controls and inter-
fering with ventilation, and are
usually poorly maintained.
These experiences give shad-
reflected radiation has ing a poor reputation.
to pass through glass Options for shading fall
radiated and convected
into four categories5 – Exter-
heat inside room nal, Internal, Interpane and
Typical solar gain factor for Integrated.
internal white louvres: 46%
It is well known that the
thermal performance of exter-
nal shading is superior to
internal shading, since re-
emitted heat is lost to the
outside, rather than into the room, as shown in
Figure 5.13 Comparison between external and internal
Figure 5.13. However, internal shading is usually
shading
cheaper and easier to control.
5 These notes are intended to assist in strategic decisions about shading. Detailed design and specification should use
analytical design tools to assess the performance quantitatively.
58 Practice
Interpane shading refers to devices held be- External shading

tween panes, or in the cavity of a ‘double skin’
envelope.These systems have the advantage that External shading broadly falls into the following
the shading device is protected from weather, types:
dust and mechanical damage. It is important that
the design of the cavity permits adequate venti- • overhangs (fixed or retractable);
lation to the shading elements. • louvres (fixed, adjustable, retractable);
Integrated refers to devices such as lightshelves • fins (fixed, adjustable);
and prismatic systems which explicitly address • blinds (retractable);
the daylight distribution function as well as • perforated screens (fixed).
selective shading.
Shading Orientation View Nat vent Daylight Seasonal Modulation Notes

type (in limiting (in limiting response
conditions) conditions)
overhangs
fixed 180 +/- 30 good good medium medium none e.g. canvas
retract 180 +/- 30 good good good good good awnings +
adjustable
geometry
louvres
fixed 180 +/- 30 med – good medium medium none view
adjust all poor good good good good influenced by
retract. 180 +/- 30 med – good good good medium blade module
retract.+ all poor good good good good size & geom.
adjust med/good ‘good’ applies
med/good to when
retracted
fins
(vertical)
fixed 90, 270 med – good medium medium none view
+/- 20 poor good good good good influenced by
adjust 90, 270 med blade module
+/- 45 size & geom.
blinds
retract all poor/good poor good good medium ‘good’ applies
to when
retracted
perforated
screens
fixed all poor med - poor poor poor none not
recommended
Windows 59
distribution by using a combination of high and

fixed – fixed low reflectance finishes. If the upper surface is
light, and the lower surface somewhat darker,
adjustable – remains in position but radiation
light will tend to be directed upwards towards
transmission can be modulated (e.g. altering
the ceiling, thereby improving the illumination at
angle of louvre)
the back of the room. Some proprietary systems
retractable – can be removed completely from use specially shaped louvres with specular (mir-
the aperture ror) reflecting surfaces, in order to further
improve the performance.
Most internal louvre systems are retractable,
A summary of their properties is given in Table allowing maximum daylight transmission at
5.3. When using the table please note the times of limited daylight availability. This also
following: permits cleaning.Whilst open louvres can allow
a good flow of air, they should be anchored top
• Orientation all implies that performance is and bottom to prevent movement and noise.
not orientation-sensitive, although in general, However, access to window opening controls
there would be no demand for shading on must be provided.These conflicts often result in
facades orientated towards the poles +/–45°. low cost simple installations being of poor func-
• Adjustable louvres and fins will have poor tional quality, as shown in Figure 5.14.
view performance and poor natural ventilation
performance, when completely closed.
• Natural ventilation limiting conditions refers to
situations requiring the shading to be de-
ployed, that is when there is an overheating
risk. Good implies that natural ventilation is
not impeded.
• Daylight limiting conditions refers to minimal
daylight availability when there would be no
requirement for shading. Good implies that
the shading devices cause no reduction in
daylight transmission in these conditions.
• Distribution refers to the ability of the shading
device to improve daylight distribution,
thereby lowering the total daylight required.
• Seasonal response refers to the ability of the
shading device to respond to different sun Figure 5.14 Office in Athens where internal louvres
angles at different seasons. interfere with the opening windows and ventilation.
A REVIVAL project before refurbishment
Internal shading
This is often the choice for retrofit. Options are
limited to louvres (venetian blinds) and roller Roller blinds
blinds of translucent or opaque material. These are another common retrofit solution due
to their low cost and ease of installation. Con-
Horizontal louvres sideration must be given to the optical properties
These offer some possibility for improved light of the fabric as indicated in Figure 5.15.
60 Practice
ately high light transmission could become glare

sources themselves when illuminated by direct
sun.
Blinds with an aluminized surface on the out-
longwave radiation side have a good performance, reflecting both
5% reflected visible and near IR radiation. If the aluminium
5% transmitted
convected heat coating is applied to 100 per cent of the surface,
no light will be transmitted, allowing total black-
out to be achieved. However, the internal surface
dark coloured blind: internal surface looks dark facing the room can still be white or light
coloured, providing improved lighting perform-
ance at night under artificial lighting, compared
with a black or dark coloured blind. Blinds with
partial aluminizing on the outside surface will
show improved shading performance and also
present a moderately luminous surface inside.
70% reflected
Both types have reduced heat loss at night due to
the low emissivity of the metallic surface.
diffuse light When roller blinds are used in conjunction
with overhangs, consideration should be given
to positioning them so that they deploy upwards
light coloured blind: internal surface looks very bright – that is, with the roller at cill level.This means
that sunlight striking the lower part of the win-
dow beneath the overhang will be intercepted,
whilst allowing light and view through the upper
part.Alternatively, the lower part of the window
can be shaded separately.
surface looks dark
5.5 High performance daylighting6

5% transmitted
High performance daylighting is an integrated
5% reflected approach that takes all the functions of the win-
dow system and room into account. The
externally aluminized light coloured blind: principle is to maximize the benefit of daylight
internal surface looks dark for external light but
reflective to internal artificial light
and to minimize the disbenefit. This involves
three actions:
Figure 5.15 Optical properties of blind materials 1 Increasing the luminous efficacy of the
light (reducing its heating effect) by the
Roller blind fabrics are usually optically dif- specification of the glazing.
fusing, which means that light is re-emitted in 2 Improving the spatial distribution of light
all directions.This means that blinds of moder- in the room to reduce over-illumination.
6 This topic is dealt with in more detail in Revival Technical Monograph 4: High Performance Daylighting, available
on the website www.revival-eu.net.
Windows 61
3 Responding to the varying availability of

light from the sky diurnally and seasonally
to prevent over- or under-illumination.
In most cases, large improvements can be made

with glazing and shading elements, and control
systems, without necessitating major structural
alterations. This makes high performance
daylighting an appropriate objective for refur-
bishment projects.
Atria and Double Skins

6
Although originally referring to the open-to- location for shading devices, and possibilities re-
the-sky central court in classical Roman houses, lating to ventilation exchange between the
the atrium was reinterpreted in the 1970s and outside, the void and the building.The intelligent
1980s to mean a large prestigious glazed space, skin – an envelope that responded to changing
usually part of a non-domestic building. Its as- environmental conditions – had long been a
sociation with energy conservation possibly dream of architects; now, with relatively conven-
stemmed from work carried out in Cambridge tional materials and a bit of help from IT-driven
in the 1970s, where the energy implications of ‘intelligent’ controls, it was achievable. However,
covering over courtyards was analysed, with the rather like atria, few double skin buildings have
conclusion that there was indeed a potential for
energy saving, provided the space was not
heated.There then followed an epidemic of atria
all claiming to be energy saving, although in al-
most all cases, the lighting, heating and often
cooling of these spaces, together with the re-
duced availability of daylight and natural
ventilation to adjacent fully occupied spaces, ac-
tually meant that these features were costing
extra energy, rather than saving it. In spite of this,
due no doubt to the architectural potential of
these spaces, the atrium continues to be popular.
The double skin has a slightly different ori-
gin. Although historic precedents exist from the
1960s, in particular the innovative Wallesey
School (Figure 6.1), the term has become widely
used only in the last two decades.The continued
love affair between architects and glass was being
strained by calls for better energy performance
than could be delivered by a conventionally
skinned curtain-walled building, even with the
improved thermal performance of low-e double
glazing units.
Double skins, distinguished from double-glaz-
ing by the use of a gap between the layers of Figure 6.1 Wallesey School by Morgan in 1967, set out to
anything from 0.3 to 1.5 metres, not only offered be self sufficient in energy, combining a double skin south
improved thermal resistance, but also provided a facade with highly insulated thermal mass
64 Practice
Figure 6.2 The ratio of the protected area to the external

envelope of the atrium is a key parameter in its thermal
protected area performance
type A type B type C
been shown by monitored results to have dra- However, if the principle of the atrium re-
matic improvements in energy performance. maining an unserviced space is adopted, then
Furthermore, it is difficult for theoretical analyses atria do have a potential for reducing energy
to show an advantage over a conventional par- consumption, particularly in the refurbishment
tially glazed, well-insulated building, unless of existing buildings. Similarly, there is a role for
optimistic assumptions are made. the application of a second skin to an existing
average average
internal external
temp °C temp °C
30 30
example
20 20 • Draw a straight line between

appropriate points on the internal
and external temperature scales.
10 10 • Choose scale according to glazing

type.
• Draw vertical line from ratio of
0.25 0.75 1.25 2 4 10
scale 1 0 glazing areas.
0.5 1 1.5 3 6
• From intersection move horizontally
0.25 0.75 1.25 2 4 10 to either temperature scale for
scale 2 atrium temperature.
-10
0.5 1 1.5 3 6
0.25 0.75 1.25 2 4

scale 3
0.5 1 1.5 3 6
ratio of area external glazing to area glazing in

separating wall
scale 1: double external / single separating Figure 6.3 Nomogram for predicting the average
scale 2: double / double or single / single
scale 3: single external / double separating temperature
Atria and Double Skins 65
building. In both cases this stems from the poor temp. °C

environmental performance of the existing en- 20
velope.
15 gla
z ing
6.1 Atria and energy: Principles ratio
0.75
seasonal shift
gl
a
10 gr
zi
atio
n
Thermal performance
0.25
The concept of the atrium stemmed from the 5 external temp.
idea of enclosing an otherwise open space,
thereby ‘improving’ its environment.This would 0
not only reduce the heat losses through that part Oct Dec Fe b Ap r
of the envelope protected, but would also in-
crease the utility of the outside space. temp. °C
The impact of the atrium is very dependent 20
upon the geometry of the situation. Consider the r
ola
2 cases in Figure 6.2. In case A the area of exter- 15 iths
w ted
nal envelope of the atrium is at least twice that of insula
olar
no s .
the area of the parent building that is protected
10 p
– referred to as the separating wall. In case B, the m
r n a lte
exte
reverse is true.We say that the atrium in case B
has a higher protectivity than in case A. Rather 5
than areas, the key parameter is actually the ratio
of the overall conductance of the separating wall 0
to the external atrium envelope. Figure 6.3 Oct Dec Fe b Ap r
shows a nomogram for calculating the mean
atrium temperature as a function of this param-
eter. Figure 6.4 Predicted monthly temperatures for a typical
The temperature will also be strongly influ- unheated atrium, for different glazing ratios (R) of the
enced by the availability of solar gains.This also separating wall, for sunny and non-sunny days, and
depends on the solar geometry of the atrium replacing the atrium glazing with insulated opaque
envelope, namely the amount and inclination of envelope
south-facing glazing, compared with ‘non-solar’
glazing. This is referred to as the solarity of the the separating wall – here denoted by 75 per cent
atrium. The two parameters, protectivity and and 25 per cent glazing ratio, and of the effect of
solarity, can combine to give widely differing solar gains.
performance. Clearly temperatures in the daytime will be
higher than the monthly average since the oc-
Winter performance cupied building will be heated, and the solar
gains will all be present during the day. This is
Figure 6.4 shows the monthly average winter indicated by the simulated results shown in Fig-
temperatures for an atrium in UK climate. Since ure 6.5, and again in Figure 6.6.
the temperature in the atrium is variable, it is ap- The increased temperature of the atrium will
propriate to refer to it as a climate. Hence its obviously reduce heat loss via the separating wall,
impact can be described as a climatic shift. Note during the heating season, and hence heating
the effect of the two values of conductance of load. If it is possible to draw ventilation air from
66 Practice
temp. °C
20 no atrium
thermostat interior temp.
nny day
set temp. - su
15 ium MWhr
atr
cloudy day 140
ium -
10 atr
independant building
night set back 120 to atrium
5 atrium
external temp.
occupied period 100 to building
0
6 12 18 24 hour 80 recirculate
60
Figure 6.5 Predicted hourly temperatures of a typical
atrium 40
20
temp. °C
0
25 n y a b c d e
rs sun
tio nh
20 cc upa
no
Figure 6.7 Annual heating energy consumption for a
a udy
me rs clo
c u p a tion h building with an atrium showing the impact of ventilation
oc ly
15 mean onth pre-heating
nm
mea
10 al
ern
ext
to retrofit is where the existing wall becomes the
separating wall, and this part of the envelope can
5 be left leaky to encourage air exchange. Recir-
culation alone will not provide fresh air into the
0 system, so the atrium must be provided with
Jan Feb Mar Apr May
fresh air, and air should be monitored in the oc-
cupied building to ensure sufficient air quality.
Please note, these temperatures and energy
Figure 6.6 Daytime temperature increment over monthly consumption figures are for a south-facing
average atrium of type B, and are indicative only. Due to
the variability of the performance of atria, it is
recommended that detailed thermal analysis is
the atrium instead of the outside, the ventilation carried out to verify the beneficial effects of a
heat load will also be reduced. This can lead to proposed intervention, if present.
dramatic reductions in heat load, as illustrated in Winter ventilation to the atrium allows the
Figure 6.7. supply of fresh air to the parent building if ven-
In most real situations it will not be possible tilation pre-heat mode is adopted. Unless the
to draw all the ventilation air from the atrium, at atrium is densely occupied, it will not in itself
least without mechanical ventilation. Openable demand high rates of ventilation. Figure 6.8
windows in the separating wall will probably re- shows the use of high level openings which
sult in a mix of the ventilation modes, in varying causes good mixing, and avoids stratification.
proportions. Something of particular relevance
cold plume entrains Tamb

warmer air
h
Tave
Figure 6.8 High level ventilation for winter provides

mixing as the cold plume descends to floor level Figure 6.9 Ventilation top and bottom encourages
maximum ventilation for summer. Stratification ensures that
the atrium is coolest at floor level
Summer performance
The benefit of increased temperature in winter
becomes disbenefit in summer. Not only may
the increased temperature render the atrium
space itself too hot for comfort but the parent
building can suffer from both conductive heat
gains and gains from ventilation. Stratification of
temperature may mean that even if the atrium is
comfortable at ground level, high temperatures at
the top of the atrium may be transferred to the
interior surrounding spaces (Figure 6.9). So the
priority shifts to keeping gains to a minimum
and ventilation at a maximum.
Figure 6.10 Shading and ventilation to prevent summer
This can be achieved by adequate ventilation,
overheating
preferably with inlets top and bottom to en-
courage ventilation by stack effect during
periods of low windspeed. As a rule of thumb 6.2 Effect on daylighting
the openable area should be no less than 10 per
cent of the ‘solar’ glazing area.The glass exposed In almost all cases the presence of an atrium will
to solar radiation should be shaded with move- reduce the availability of daylight to the sur-
able shading, especially horizontal or shallow rounding rooms. This is due to the absorption
inclined glazing which receives most radiation in due to the glazing material and obstruction of
the summer.A schematic diagram in Figure 6.10 the supporting structure.This can easily be a re-
illustrates desirable characteristics of an internal duction of as much as 50 per cent.
shading system. The general characteristics of It may be that some compensation can be
shading types are dealt with in Chapter 5. made by adopting very light coloured (reflective)
68 Practice
finishes for the atrium floor and opaque parts of spraying leads to high humidity, and condensa-
the separating wall. Or it may be possible to in- tion on the glass. The response to this in cool
crease the glazing area in the most obstructed climates is often warm-air curtains and hence a
part of the separating wall. In any event, fixed large consumption of energy.Watering should be
shading and reduced transmission glazing to the piped to the roots and electronically controlled
atrium envelope should be avoided, unless the to avoid wasteful evaporation. In cool climates,
existing building is already grossly over-glazed. deciduous species should be considered as these
This issue should be investigated by calculating a will cause less obstruction to daylight in the win-
corrected daylight factor for the occupied rooms, ter season.Avoid green tinted glass for the atrium
and using this to predict daylight availability from glazing; plants do not like green light – that is
sky luminance data. why they reflect it.
6.3 Planting and vegetation 6.4 Double skins and energy

Plants can use energy! Plants occupy the spaces The double skin can be looked upon as a special
all day every day, so any conditioning (e.g. heat or case of the atrium, where all (or part of) the en-
light) has to be maintained for long periods. If velope has become the separating wall, and the
energy saving is a priority, it is essential to chose atrium space has become an unoccupied cavity.
plants that can tolerate a cool season, and prob- A double envelope on all surfaces, including the
ably relatively low light levels, and require no or roof, is unusual; typically one of more major
minimal conditioning. Even the mode of water- glazed facades will be treated.
ing can have an indirect effect; watering by The thermal benefits are similar – reduced
conductive and infiltration losses, with the po-
tential for ventilation pre-heating. But the
disbenefits are there too, with overheating of the
cavity being the largest threat. Because, typically,
double envelope buildings have highly glazed
envelopes, the building is more closely coupled
with the conditions in the cavity, making con-
trol of these conditions, by shading and
ventilation, of vital importance.
For this reason, heavy reliance is often made on
‘intelligent controls’. However, both the control
software and the hardware (e.g. the mechanical ac-
tuators) are notorious for error and mechanical
failures. Wear and tear and erratic maintenance
schedules mean that these buildings may not age
well, and cannot be seen as robust design.
6.5 Other environmental factors

Open sky has an acoustic absorption coefficient
of 100 per cent at all frequencies. As soon as a
Figure 6.11 This exotically planted atrium required space is enclosed, this absorption is lost and the
permanent artificial lighting due to the choice of green glass reverberation time is increased.This can become
for the envelope troublesome both for speech intelligibility
within the atrium, and the propagation of noise skin as part of a sustainable refurbishment project.
from sources in the atrium to the inside of the Table 6.1 shows the advantages and disadvantages
building, or even from inside the building to for atria and double skins. It should be used
other parts, via the atrium. when considering adopting either strategy in re-
Treating opaque surfaces with acoustic ab- lation to particular characteristics of the original
sorbers can help reduce the problem. Walls, building.
shading devices, opaque roof sections can be
treated; materials such as timber strips covering Summary
mineral wool can provide good mid-frequency Many of the advantages and disadvantages are
absorption and still maintain an appearance of an linked – for example, a second skin offers some
external finish.There are also micro-porous min- acoustic protection, but it is lessened by the need
eral materials that have similar properties. The to ventilate the cavity in summer; an atrium of-
acoustic properties of vegetation are often exag- fers some reduction in heat load, but it may be
gerated, but a heavy planting scheme will smaller than the extra lighting energy to com-
definitely make some improvement. Reverber- pensate for the reduction in daylight.This makes
ation time, and its interference on speech, are generalizations difficult, since it is only after de-
easily calculated from published materials data, tailed analysis, which may involve both
and it is recommended that this analysis be done. quantifiable and non-quantifiable performance,
Flanking sound transmission, from source to that the net benefit or otherwise of these inter-
receiver both located inside the building, via the ventions can be evaluated. However there are
cavity, is more typical of double skin buildings. some strategic rules that are reasonably robust:
This will definitely occur if two separate spaces
open onto a common cavity. However the effect • An atrium is likely to be most effective in cool
can be mitigated, as before, by including sound climates, and when the geometry of the ex-
absorption within the cavity.This may be in the isting building gives the opportunity for an
form of surface treatments, or provided in part atrium of good protectivity and good solarity.
by shading devices, usually located in the cavity. • In warm climates solarity may lead to over-
In these cases, the reflective path of the sound heating; shading and large openable areas for
should be considered when deciding which sur- ventilation are essential.
faces to treat, in order to optimize its effect. • It will be most cost effective when the parent
Other considerations – for example, fire- building provides the primary support struc-
compartmentation and ventilation control – may ture for the atrium envelope.
result in the specification of separated cavities, • A double skin will be most cost effective
that is each window or group of windows from when the costly upgrading of the original
one room, opening onto a single cavity.This will envelope can be avoided. It has the largest en-
largely solve the acoustic problem provided the ergy impact when the original envelope is
separating elements have reasonable sound insu- poorly insulated and leaky. It follows that it
lating performance. For all of these reasons, the has a larger effect on facades that are already
separating elements should be well sealed. highly glazed. For a partially glazed facade it
is probably more effective to upgrade the
6.6 Atria and double skins as part of opaque envelope and the glazed areas sepa-
sustainable refurbishment rately.
• For facades exposed to direct sun it is essential
Most of the above applies to both new and retro- that the double skin incorporates shading and
fit atria or second skins. Here we consider issues ventilation, and a control system that allows,
particularly related to a retrofit atrium or second but does not rely on, human intervention.
70 Practice
Table 6.1 The advantages and disadvantages of atria and double skins
Advantages Disadvantages
Atrium Significant heating energy reduction if geometry Does not give significant energy savings if
provides good protectivity and good solarity. protectivity and solarity are poor.
May offer further energy saving by ventilation Reduces availability of daylight to rooms and may
pre-heating. thereby lead to increased energy consumption.
Can provide useful semi-climatized space at low Reduces the potential for natural ventilation by
capital and running cost. openable windows due to
• propagating noise
• reducing windspeeds
• delivering overheated air in summer
• need for fire-compartmentation.
Provides strong architectural element making The space may overheat in summer reducing its
the benefits to the user of the refurbishment utility, and may also cause overheating in
very evident. adjacent spaces.
Will probably mean that the upgrading of the original If heated, cooled and lit, the extra energy
envelope that becomes the separating wall, can demand will almost definitely outweigh the
be to a far lower standard than if it continued to thermal energy saved.
be external envelope.
May assist in stack-driven extract ventilation
for surrounding spaces.
Double skin Significant heating energy reduction when applied Small heating energy reduction when applied to
to very poorly insulated envelope. moderate or well-insulated envelope.
Significant reduction in infiltration when applied May lead to overheating of parent building on
to leaky envelope. E, S and W facades.
Provides location for active shading system to Large surface area of glazing, shading, and
original glazed facade. support structure incurs high costs.
Can provide some noise attenuation from external Reduces the potential for natural ventilation by
noise, but much reduced if cavity is open for openable windows due to
ventilation. • propagating noise
• reducing windspeeds
• delivering overheated air in summer
• need for fire-compartmentation.
Provides architectural opportunity to change Leads to separation from outside and disruption
and upgrade appearance of the building. of views for occupants.
Final note of caution:Atria and double skins do not and/or comfort problems. Double skins con-
automatically save energy; in many cases they sume a large amount of embodied energy for no
will lead to an increase in energy consumption increase in floor space.
Mechanical Services and

7 Controls
Mechanical services and controls have a large rarely, the seasonal efficiency was considerably
impact on the energy performance of a building, reduced from the instantaneous efficiency, typic-
typically as much as the fabric. Clearly, the po- ally as low as 55 per cent. Modern boilers have
tential for improvement will depend on the addressed this problem with improved heat ex-
current state of the mechanical equipment, changers and control and can return seasonal
which typically is updated more frequently than efficiencies as high as 85 per cent. Other im-
the building fabric. However, even recent ser- provements include improved combustion, and
vices upgrades may not have attended in in the case of condensing boilers, the latent heat
particular to improving energy performance. For that would otherwise be lost with the water
example, it is not uncommon to see new low vapour, a combustion product, is reclaimed from
energy light fittings providing higher than nec- the flue gas by condensation.
essary illuminance levels, and without controls, Condensing boilers can give the highest effi-
where no saving or even increased energy con- ciency if the return water temperature can be
sumption is the result. kept below 55oC for prolonged periods.This is
It is difficult to generalize but improvements possible if emitters, such as fan coil units or un-
in plant will tend to be more cost effective than derfloor systems, are sized appropriately, (i.e.
improvements to the fabric. Updating, or in- larger than for high water temperatures) and if a
stalling controls for the first time, is even more controller is used that reduces flow temperature
likely to be the most cost effective strategy.With when demand is low, but allows higher temper-
the steady development of IT and its cost re- ature for warm-up and very cold periods.
duction, large savings can be made for modest It is common to use multiple boilers so that
or even no extra cost, resulting in a rapid pay- individual units can be fired up as necessary,
back. When considering embodied CO2, the maximizing the number of boilers working at
payback is even more rapid since the material full load and thus their highest efficiency. This
content of control equipment is very small. arrangement also gives the opportunity to use a
combined heat and power (CHP) system, or
7.1 Boilers condensing boiler as the lead boiler, with less ef-
ficient (but possibly cheaper) boilers brought
Boiler efficiency is the ratio of useful heat out- into use at times of peak demand only.
put to the calorific value of the fuel input. Separate boilers for space and (centralized)
Boilers are required work at a range of outputs in sanitary hot water can be used and this may be
response to the varying seasonal heat load. A more efficient where annual demand profiles are
characteristic of older boilers with heavyweight very different, or where small quantities of hot
heat exchangers was reduced efficiency at part water are required for summer periods.
load, often as low as 45 per cent at one-third full
load. Since full load operation occurred relatively
72 Practice
7.2 Heat distribution rate is being modulated by constrictor valves, sig-

nificant savings can be made by the use of
Water variable flow-rate pumps.
Distribution systems can be wasteful in three

ways: Air
Similar considerations apply to air ducting where
1 Zoning (of pipework) does not allow the it is part of a warm-air heating system or full air-
spatial matching of demand with delivery. conditioning. Losses or gains from between the
2 Pipe runs are poorly or non-insulated even duct and ambient air can be significant.The con-
when losses are not within the heated en- dition of the duct insulation must be assessed and
velope. the specification upgraded to bring it to at least
3 Pipe diameters are too small, incurring current standards.
high pump energy use. CO2 emission from electrical fan energy can
be as great as that from the heat production in
Modest interventions to the pipework could im- the boiler (Figure 7.1).This is influenced by the
prove zoning, and together with valve actuators resistance of the ductwork and the flow rate.
could be part of a general system upgrade. It will Again it is less likely that the ductwork will be
be particularly relevant when use patterns in the increased in size, but it is possible that air vel-
building are changing, and maintaining the orig- ocities can be reduced in response to lowered
inal zoning would lead to wasteful heating.The demand, and variable volume fans installed into
appropriate zone/time controls are obviously an existing ductwork will allow demand for heat,
essential part of the improvement. coolth or fresh air to be more closely matched
The retrofitting of pipe insulation will be pos- with occupancy.This could make significant sav-
sible in most cases. Special attention should be ings in fan energy. Variable speed drives for
paid to outdoor distribution mains, where heat
losses do not contribute to useful heating, and
the effects of weather and ingress of water may
have severely degraded the original insulation. It
Air-conditioned
is likely that older pipe insulation will contain 200

annual CO2 emissions kg CO2/m2
misc.
asbestos, and this alone will probably justify its 175 office eqpt.
replacement on health grounds.
150 fans & pumps
Small pipe diameters will lead to higher en-
ergy consumption by the circulation pumps. It refrigeration
Naturally ventilated
125
may be possible to reduce flow speed due to re- lighting
zoning. It may also be possible to reduce flow 100 heat & hw
rates in response to reduced heat demand due to
75
insulation improvements.Where this is not pos-
sible, replacing existing pipework with that of 50
large diameter could be justified; for a given flow
25
rate, the energy consumed is inversely propor-
tional to the fourth power of the pipe diameter. 0
However, it is not only the pipework causing
flow resistance, but often components such as
valves, junctions and bends, and the resistance of Figure 7.1 CO2 emissions by energy end use by 14 office
these should be minimized. Furthermore, if flow buildings in the UK
Mechanical Services and Controls 73
Figure 7.2 Different

kinds of heat emitter
70% + convection 50% convection
30% - radiation relying on convection
50% radiation
and radiation in different
proportions
RADIATOR UNDER FLOOR
90% convection
70% radiation
30% convection
CONVECTOR CEILING PANELS
energy use. During the general upgrading of a

system, lowering flow resistance of the whole
95% advective system by improved components and design
modifications will lead to energy savings.
The most significant savings are likely to be
made where mechanical air handling can be re-
moved altogether due to lowered demand for
heat and coolth brought about by fabric meas-
ures such as insulation and/or shading.
FAN COIL
7.3 Heat emitters
ventilation fans controlled by CO2 sensors are
very effective at reducing fan energy use. See sec- Heat is emitted into the room by one of six
tion 7.4. methods (Figure 7.2):
Closely related to duct size and the resulting
flow resistance, is the resistance of air-condition- 1 radiators;
ing components such as noise attenuators, 2 convectors;
humidifiers and filters. Filters are frequently neg- 3 fan coils;
lected and pressure build-up due to clogging will 4 underfloor heating;
activate a by-pass, thereby delivering unfiltered 5 high level radiant panels;
air, or increase the flow resistance and increase 6 via the ventilation air.
74 Practice
It is well known that the conventional radiator is ceiling, possibly exacerbating roof losses or ven-
predominantly a convector with more than half tilation losses from high level openings.
of the energy being emitted by natural convec- However, if the ceiling is very lightweight, this
tion. Multiple panel radiators (two or three will warm quickly and begin radiating down-
layers) have a higher proportion of convective wards. Air leaves the fan coil unit with much
output, and the convector simply takes this fur- more momentum than the simple convector and
ther by increasing the heated surface area, usually can be directed horizontally ensuring rapid mix-
enclosed by a casing. Fan coils takes the princi- ing.
ple one more step by forced air flow ensuring The underfloor system increases the radiant
that more than 95 per cent of the heat output is temperature and the air temperature over the
to the air.All of these emitters have to be located whole floor surface.This can be rapid in the case
against walls, usually perimeter walls where the of the lightweight deck, or rather slowly when
greatest heat loss is located. the heating pipes are located in a screed, due to
Underfloor heating is achieved by heating the thermal inertia of the heavy material. Hori-
pipes in the screed or under the deck as de- zontal ceiling radiant panels radiate downwards
scribed in section 2.2. It introduces heat over the increasing the radiant temperature and warming
whole area of the floor (or the zone in which the floor.
the pipes are located) with about 50 per cent as These dynamic and spatial differences can
radiant energy and 50 per cent convective. have considerable influence on energy con-
Radiant panels in the ceiling, if horizontal, sumption, and should be considered when
have the highest proportion of radiant energy for replacing heat emitters. For example a large dou-
any low temperature emitter.This is because up- ble-height space of heavyweight construction
ward-flowing convection currents cannot be set would respond very badly to perimeter radiators
up, resulting in a higher surface temperature and or convectors, whereas smaller spaces with a
hence higher downward radiant loss. lightweight well-insulated ceiling, will be effec-
The location of the emitter and its radi- tively heated by such a system. Fan units carry
ant/convective split influences the temperature the advantage of a high output for small size, and
distribution, in particular in the warm-up period. the ability to cause good mixing and fast re-
Consider the cases in Figure 7.3. The vertical sponse; however, the fans use electrical power,
warm-air plume from the radiator or convector make noise and require maintenance.
has to ‘fill up’ the room from the top down be- Thermal comfort can be achieved at relatively
fore the air temperature increases at floor level. low air temperatures provided the mean radiant
This will lead to high temperatures under the temperature1 is higher. Overhead radiant panels
Figure 7.3
Transient effects
warm air during warm-up
period for
different emitters
cool air
1 The average effective temperature of all surfaces surrounding the occupant.

Figure 7.4 Providing

comfort at a higher mean
radiant temperature
allows air temperature to
be lower, thereby
reducing ventilation heat
loss
can achieve this, making them suitable for spaces cellular offices or meeting rooms are built around
such as workshops, sports halls and warehouses the perimeter of rooms with open plan areas in
(Figure 7.4). Lowering the air temperature will the centre.These refurbishments often make no
lower conductive heat loss through the fabric, provision for changing the heating system, re-
and loss by ventilation, which may be high from sulting in unbalanced heated environments in all
large volume spaces such as these. To some ex- areas.
tent, underfloor heating also elevates mean
radiant temperature, and delivers the heat at floor
level, making it suitable for spaces with large ceil-
ing height, including ‘semi-heated’ spaces such as
cool air
atria.
High-temperature directly gas-fired heaters curtain
and electric incandescent heaters are available for increased high temperature
high level installation in similar circumstances. heat loss
Here, relatively small areas are heated to high
temperatures (400°C to 850°C).The overall ef-
fect is similar to large areas of surface at a lower
temperature. However electric heaters should be
avoided if possible due to the large CO2 emis-
sions per kWh of electricity.
Figure 7.5 Poor positioning of heat emitter leads to
increased losses due to high local air temperatures
Positioning emitters
Radiators and convectors are often placed at the
perimeter of rooms on external walls, and often
Sizing emitters
beneath windows. Both can lead to high local air
temperature, and if this is against a poorly insu- Reduced heating loads give the opportunity of
lated wall or a window, heat losses will be reducing emitter size.This may be an advantage
significantly increased. This is particularly true in terms of space use, and a saving in capital cost.
when windows are curtained, if the warm air is One consideration, however, is that the larger the
channelled into the space between the curtain output of the emitter the lower the water tem-
and the window, as in Figure 7.5. Further issues perature needs to be for the same heat output.
arise during refurbishment programmes when Lowering water temperature reduces non-useful
76 Practice
heat losses from pipework, reduces flue temper- temperature is below the dewpoint, condensa-
ature, and increases heat recovery in condensing tion will form. This is unacceptable for floors,
boilers. Low water temperature also leads to and probably ceiling panels, but can be handled
higher efficiency when heat is supplied by heat in fan coil units, where the collection of con-
pumps, geothermal and waste heat sources. densation effects a dehumidifying function.
Underfloor heating is slightly different, since
the maximum water temperature has to be low 7.4 Fans and pumps
for comfort reasons (avoiding hot feet). The
penalty is that a large area is required.This means CO2 emissions due to the electrical energy con-
that underfloor heating is a good choice for low sumed for circulating air by fans and water by
energy use, provided the response time is appro- pumps can be as large or larger than that for
priate for the heating regime (see Section 2.1). heating or refrigeration (Figure 7.1). Much of
this is due to wasteful control – that is, moving
more air or water than necessary – and this can
Coolth emitters be taken care of by improved controls, see section
Cool air is heavier than warm air, resulting in the 7.7. However, the technical characteristics of the
natural convection currents illustrated in Figure fans and pumps themselves affect energy use.
7.6 being reversed. Horizontal cooled surfaces Refurbishment may provide the opportunity to
behave differently from heated surfaces in that a change to more efficient equipment in itself, or
cooled ceiling can deliver cool air to the floor, incorporate new features such as variable speed
by downward flowing plumes, and a cooled floor drives which permit a more efficient control
creates a layer of stable cool heavy air. It is un- strategy on ventilation air.
usual to use conventional radiators or passive Ventilation fans will be designed to satisfy the
convectors for cooling purposes but in principle highest annual demand and lower ventilation
this can be done. All other emitters are suitable, rates will be adequate to maintain air quality for
thus it is feasible to use the same emitters for much of the time.Variable speed drives can be
both heating and cooling. Cooled floors and retrofitted to fans and controlled by CO2 levels
ceilings carry much the same advantages as for in the exhaust air or by set profiles according to
heating applications, including their large surface time of day.
area allowing small temperature differences.This Water circulation pump speeds can be con-
may permit using ambient coolth sources such trolled by pipe pressure so that where flow is
as ground or seawater. reduced as valves close down due to thermostats
However, a new problem emerges with sensing adequate temperatures, pump speed is re-
coolth delivery – condensation. If the surface duced, greatly reducing power usage. Modern
Figure 7.6
Downward cool
air plumes from
cooled ceiling
panels (a) and
stable stratified
cool air from
cooled floor (b)
pumps and fans are generally much more effi- used directly through walls, windows or ceilings.
cient than older equipment. These normally provide cool air directly to the
space with heat dumped via a fan coil to outside.
7.5 Refrigeration Low efficiencies and poor control may make
these installations inefficient for long-term use.
Where active mechanical cooling is required in Where there is an available source of ‘waste’
a building, this can be provided by a variety of high grade heat, in or adjacent to the building,
systems giving varying efficiencies. These are absorption chillers can be used to provide cool-
mechanical central chillers, using one of: ing. These are similar to conventional chillers but
use heat rather than electricity to drive the
• absorption chillers; or process of producing cold water. Absorption
• local ‘split-unit’ heat pumps. chillers are most commonly used where there is
a combined heat and power (CHP) system close
Conventional refrigeration plant produces by, with surplus heat, particularly in summer.
chilled water that circulates around the building Overall efficiencies of absorption chillers are low
supplying fan coil units or other emitters where and careful calculations are needed to ensure that
necessary. Efficiencies vary between machines they can in practice provide a low CO2 cooling
using different types of compressors. system. Absorption chillers have also been used
Chillers can ‘dump’ heat from the building to in conjunction with solar heat sources.
the external environment via: Chillers are rated in terms of efficiency by their
Coefficient of Performance (COP), which is the
• wet cooling towers; extracted heat energy divided by the electrical en-
• dry cooling towers; ergy input. Instantaneous COPs can vary up to 4
• using the ground. or 5 for a high performance and/or magnetic
bearing chiller, but it is the annual performance,
Wet cooling towers give the highest efficiency taking into account periods of low demand, that
but if not fully maintained have been linked as is the key to low energy use. It must also be borne
sources of Legionnaire’s disease and as such re- in mind that conventional electrical energy has a
quire regular, effective maintenance and control. much higher CO2 content than thermal energy.
Fan-driven dry systems are becoming more
common as they do not have any links to Le- 7.6 Lighting installations
gionella, due to the removal of moist, warm
breeding grounds, but are a less energy efficient
Luminous efficacy
method of dumping heat.
Ground sourced systems use a horizontal grid For non-domestic buildings, lighting energy
of pipes at least a metre below ground, or a ser- forms a major component of the total energy
ies of vertical pipes in which a fluid, normally consumption, as shown in Figure 7.1.The adop-
water, is circulated and cooled by the ground. tion of a strategy to maximize the use of daylight
Ground pipes can give good chiller efficiencies, in order to minimize artificial lighting energy has
depending on ground temperatures and soil been discussed already in section 1.6. It involves
types, and the cooled water can be used through maximizing the ingress of useful daylight by ar-
a heat exchanger directly to provide ‘free cooling’ chitectural means, and the use of controls to
for the building at modest demand levels. ensure that the artificial lighting is displaced by
In smaller buildings and even for supplemen- the daylight. The energy use is also dependent
tary comfort cooling in larger buildings, on the efficiency of the artificial lighting system
individual air cooled units are quite commonly itself, the subject of this section.
78 Practice
Luminous efficacy is defined as the ratio of emitted from the source, and is a property of
luminous energy (lumens) to the power con- both the luminaire and the room.
sumed by the source. The global luminous The two factors on the right are both candi-
efficacy of a system is given by: dates for improvement. Table 7.1 gives generic
descriptions of sources, luminaires and room
Eg = Es x UF
characteristics to indicate the potential reduction
where Es is the efficacy of the source and UF of lighting power. The energy use is compared
is the utilization factor. The utilization factor is with a base case which might reasonably be re-
the ratio of useful light on the workplane to that garded as a typical unimproved installation.
Table 7.1 Global lighting efficacy for various combinations of lamp, luminaire and room type
Lighting scenario Lamp efficacy Global efficacy Installed power

l/W l/W W/m2 for 300 lux
Tungsten pendent diffusing globes surface

reflectances med. maintenance poor 14 3.25 92
T12 38mm fluorescent magnetic (choke ballast)
surface mounted battens with plastic
diffusers (degraded) surface reflectance med.
maintenance poor 55 16.25 18
tungsten halogen uplighters
timber ceiling
other surface reflectance med.
maintenance average 18 3.45 87
quartz halogen recessed downlighters
surface reflectances med.
maintenance average 24 11.5 26
metal halide uplighters
ceiling nom. white other reflectances light
maintenance good 90 37.5 8
compact fluorescent triphosphor elec. ballast
recessed downlighters
reflectances med., maintenance good 64 32.0 10
fluorescent T8 tubes elec. ballast
surface batten acrylic diffusers
maintenance med. 90 42.0 7
fluorescent T5 tubes elec. ballast
surface batten low brightness
maintenance good 105 50 6
Note: Indicative values only.
Assumptions: Med. reflectance – ceiling 70%, walls 50%, floor 20%.
Utilization factor 0.65–0.75 downlighters, 0.55 uplighters white ceiling.
Light output ratios 0.5–0.85.
Illuminance level and distribution background illumination to the whole room at a

much lower level.
As a generalization lighting levels tend to be For example, a 1000m2 office has a uniform
higher than necessary. Table 7.2 gives recom- illuminance of 500 lux. If new high efficiency
mended values. Replacement at the same power lamps and luminaires are used this could be pro-
rating, with more efficient lamps and luminaires vided at 10W/m2, a total of 10kW. By reducing
will only increase illuminance levels, not save en- the ambient illumination to 150 lux, and pro-
ergy. Thus the replacement specification must viding a 12W task light to each of the 100
take account of increased light output, and workstations (giving 600 lux over an area of
possibly, reduce design illuminance to recom- 1m2), the total load is reduced to 4.1kW. It is es-
mended values. timated that this measure alone would reduce
annual CO2 emissions by more than 2 tonnes.
Table 7.2 Selected artificial illuminance levels non-
Apart from the direct saving of energy, this car-
residential buildings
ries the further advantage of reducing unwanted
Building Location Service internal gains during the warm season, thereby
type illuminance reducing overheating, or cooling energy.
This approach is particularly applicable to the
General Corridors 100 modern office with LCD display screens, which
buildings Stairs 150 are themselves luminous. If dimmable, task light-
Reception areas 150 ing allows the user to balance the brightness of
Offices general 400 illuminated documents approximately to that of
Offices + VDUs 300 the screen, or to their preference, improving vis-
Offices + task1 150 ual comfort, providing adaptive opportunity, and
lighting possibly making further energy savings.
Drawing offices 700
Drawing offices + VDU 500
7.7 Controls
Conference rooms 300
Airports & Reception areas 250 Local control
transport Circulation areas 150
buildings
Any unoccupied part of a building that is being
lit, ventilated by mechanical means, heated or
Libraries Bookstacks 150 cooled, is a potential waste of energy. In many
Reading areas 300 buildings, workstation occupancy levels are often
Schools and Classrooms 300 as low as 50 per cent, whilst there are many other
colleges Lecture theatres 200 areas such as stores, meeting rooms, rest areas and
Laboratories 400 service areas that are occupied far less.A vital role
Sports halls 500 of system controls is (or should be) to try to
match environmental conditioning with occu-
Note: 1 Desk task lighting should provide average 700 lux over 1m2. Values
indicative only – may be covered by specific codes and regulations.
pation. This matching takes place over time and
space and thus becomes the issue of time pro-
gramming and zoning.A third issue is the degree
Recommended illuminance levels are based on to which systems can respond to unprogrammed
the most exacting task to be carried out in the occupation, for example by occupancy detection
space. Large savings can be made by using task or user control.
lighting, providing high (but controllable) illu- The degree to which environmental condi-
minance over limited areas, and providing tioning can match occupancy is dependent on
80 Practice
the speed of response of the system. Artificial anticipate the answer! The difference between
lighting can respond instantaneously, and thus of- the three options would be:
fers good potential for demand matching. For a
single well defined room (such as a classroom or All the time 100%
meeting room) this is completely possible, and Afternoons + 52%
automatic switch-off with manual switch-on is Occupation only 30%
generally tolerated. In more diffusely occupied
spaces such as open plan offices, and in particu- Thus up to 70 per cent of the energy used by
lar circulation areas, it is more difficult.Walking that room is wasted. Clearly a room booking sys-
towards an unlit area, that is only illuminated tem integrated with the heating programme
when occupied, would not generally be accept- could solve the problem, although it still could
able. not cope with unpredicted spontaneous use.
Heating (and cooling) does not respond in- However, even spontaneous meetings do not
stantaneously. This makes it more difficult for occur with zero lead time – participants have to
heating to respond to occupancy. However, some be informed, documents gathered, coffee and
heating systems are quite rapid response, and if biscuits arranged. If on checking by the intranet
used in conjunction with a set-back – that is, a that the meeting room is free, the originator of
lower set temperature for standby – this form of the meeting could call environmental services for
control can be quite acceptable. For example, if that room to be activated, by the time the meet-
a room is unoccupied for more than ten min- ing was under way it could be up to acceptable
utes, the set temperature drops 4°C. comfort levels.
Mechanical ventilation consumes energy both The actual spatial and temporal occupation
from the fan power and the resulting heat loss. density of all buildings is very low. Studies have
There is no virtue in changing air that already shown that even for a nominally fully occupied
meets accepted air quality standards. Local de- office, the occupation of workstations is actually
mand control can be achieved quite easily using about 50 per cent. Other areas are even more
CO2 detectors. This is preferable to occupancy sparsely populated. Different building types such
detectors since it will respond to the numbers of as schools, hospitals, hotels and even residential
occupants in the space, rather than just whether buildings, show a similar characteristic.
the space is occupied or not. Technical solutions seem to lie jointly in the
area of communicating with the central program-
ming system, and responding locally by passive
Central control
occupancy detection or by user control.The lat-
The key issues here are time programming and ter is, of course, what we have been doing for
zoning. Time programming is technologically centuries, before the concept of central control ex-
simple, and with digital devices, the cost is be- isted, and thus before the idea that an unoccupied
coming trivial. The problem with time space should be held permanently ‘at the ready’.
programming is whether the management of the
system allows the flexibility to alter the pro-
Zoning
gramme to respond to changing circumstances.
For example, a meeting room is used three Occupancy demand matching can be achieved
times a week, usually in the afternoon, but occa- only if the centralized services are zoned appro-
sionally (once per month) in the morning. Does priately. Existing buildings have often had
the facilities manager tell the energy manager to additions to both fabric and services, and changes
programme for every day, every afternoon, or re- of use, which have led to the original zones be-
spond to each meeting? We can probably coming redundant.
For example, a community centre was built would have massive advantages in flexibility, and
with a small hall and foyer, on a single heating with appropriate software, building energy man-
circuit. Later a large sports hall is added, with a agers could configure complex zones.
second heating circuit and given independent Conditional actions could easily be programmed
control. However both halls shared the use of the in – for example – if the window sensor detects
foyer (including toilets), and the management wide open, then heating off, or if blinds down and no
had to heat the whole building when the large occupants then lighting off. Both of these examples
hall is used. Quite a small modification to the show the way the controls interact with individ-
pipework, and the addition of two motorized ual’s actions in a way that moves the result
valves, now allows any combination of the three towards a low energy outcome.
spaces to be programmed. The system could easily interact with a book-
The concept of zones applies to centralized ings diary for intermittently used spaces,
control.As zone size decreases, down to individ- ensuring that there was good occupancy demand
ual rooms or even individual appliances (e.g. heat matching.
emitters) the issue then becomes between central
control and local control. A room thermostat is 7.8 Lighting controls
an automatic local control whilst an on/off
switch is a manual local control. If all control Lighting controls have to prevent demand mis-
were at this level, it might appear that zones match in two ways. Firstly, to avoid artificially
would become redundant. illuminating unoccupied spaces, and secondly to
It is interesting to note that, traditionally, the avoid artificial illumination when there is suffi-
zoning concept is to exert control at a local level, cient daylight.
by communicating via the actual service being
provided – electricity, heated water or condi- Occupancy detection
tioned air.
Developments in IT have made exciting new The former can be achieved using centralized
possibilities.The ability to address an actuator – programming but this is unusual.The common-
a valve, a damper, a light switch – using a digital est method is to use occupancy detection in a
signal recognized only by that specific compo- room or zone. Artificial lighting in a room or
nent, has been available for some time, although zone is extinguished after a certain period of
it seems that its application is not widespread. non-detection of the presence of an occupant.
This has been partly due to cost – low-volume The detectors use passive infrared (PIR) or mi-
production, and also the cost of hard wiring the crowaves and detect movement. This has the
data bus to the component. slight problem that if the occupant is very still
But we only have to look to other application the detector may falsely detect non-occupation
areas to see the cost of wireless digital control re- and switch off the lighting. Most commonly in
ducing by orders of magnitude, and we can areas such as toilets, stores and circulation spaces,
envisage a day when every component will incor- the control will provide switch-on and switch-
porate its own digital receiver. Environmental off, whereas in areas such as meeting rooms,
components simply have to be connected to a offices and classrooms the control operates
supply – water, air or electricity – and a re- switch-off only, relying on manual switch-on.
ceiver/actuator unit placed with them. Sensors Although the control is local, zoning is re-
could also be part of the same communication net- quired because the occupancy detector will have
work, acting as control points in optimal positions. to switch a number of light fittings.These must
Virtual zones are then created, simply by be on a common and exclusive circuit unless lu-
grouping together component addresses. This minaries are installed that contain individual
82 Practice
Table 7.3 Selected daylight factors
Building type Location Average DF% Minimum DF%
General building Reception areas 2 0.6

General offices 3 1.0
Drawing offices 5 2.5
Airports & transport buildings Reception areas 2 0.6
Circulation areas 2 0.6
Libraries Bookstacks 3 1.0
Reading areas 6 1.5
Museums and art galleries General 5 1
Schools and colleges Classrooms 5 2
Lecture theatres 1 0.3
Laboratories 5 2
Sports halls 5 3.5
Note: These recommended values originated from mid Europe. For the same yield of useful daylight, values can be reduced by 40% for latitudes less than 45°N and in-
creased by 20% for latitudes above 55°N.
For more detailed version of this table please see CIBSE: Window Design Applications Manual
occupancy/illuminance detection exclusively for tric light when there is sufficient daylight be-
that luminaire’s control. comes an ethically or intellectually driven action
Stand alone occupancy-detecting light con- and not discomfort driven.
trols, are low cost (typically €30–€100) and Photo-sensitive detectors can be used to make
readily available. In buildings with intermittent up this deficiency.The most basic system moni-
room-use large savings can be made and the in- tors the illuminance in the room and if the
stallation of these controls during refurbishment illuminance value is above a datum (the design il-
should be high priority. luminance + the artificial illuminance), the
artificial lighting will be switched off.These sys-
tems first appeared in the 1970s and had mixed
Daylight detection
reception, occupants often finding them irritat-
Most non-domestic buildings, are technically ing due to the sudden change of illuminance.
day-lit – that is, there is at least a 2 per cent day- A whole series of refinements followed, the
light factor2 (DF) for 80 per cent of the floor most important being dimming control, which al-
plan – but they spend most of their occupied lowed the artificial lighting to be gradually
time lit artificially.This waste is partly due to the dimmed, as the daylight illuminance approached
lack of feedback to the occupant – that is, al- the design illuminance. This not only improved
though the occupant notices under-illumination, visual comfort, but increased the energy saving.
there is no discomfort feed back from over-illu- Other refinements included the incorporation of
mination. Thus, unlike closing a window once a time lag, to avoid response to short term daylight
the room has cooled down, turning off the elec- fluctuations, and a system where the switch-off
2 DF = ratio of horizontal illumination in the building at the point of interest to the unobstructed illumination out-
side the building, expressed as a percentage. Recommended values are shown in Table 7.3.
action occurred at specific times of the day. In both of these systems, light fittings must be
Systems installed in open plan offices were grouped together into zones, controlled by a sin-
usually under full auto control, whereas systems gle detector or predicted illuminance point, and
in cellular offices and small rooms were often these zones must relate logically to the variation
auto off and manual on. This created a further of daylight in the space.That is, they should be
energy saving due to the phenomenon of in- approximately defined by isopleths of equal day-
creased tolerance of failing daylight, where light factor (Figure 7.7). For most side-lit areas
people will delay switching on artificial light this simplifies to having two (or possibly three)
even when the daylight has reduced well below banks of light fittings parallel to the window wall
the accepted artificial lighting level. and at a distance of about 1.5 and 4.5 metres
All manual switching can have some energy from the window wall. Zoning of this kind will
saving potential. It is found that in cellular offices, show significant savings over a single zone for
with one or two occupants, it is more likely that the whole day-lit area.
the lights will be switched off when there is suf-
ficient daylight than in open plan offices.This is
Energy savings
probably due to territorial effects and the ‘taking
ownership’ of control, and is an extension of what The savings created by photo-sensitive control
we would expect to see in a domestic situation. are considerable. Figure 7.8 illustrates the effect
However, even at this scale, zonal switching is best, for both on/off control and dimming control.
allowing the lighting in areas of the room closest The low cost of the control system makes them
to the window to be switched off first. highly cost effective and their incorporation ab-
solutely essential in any non-domestic building
refurbishment.
Zoning
Two methods can be adopted: 7.9 Building energy management systems
(BEMS)
1 The available daylight can be measured
outside the building (usually on the roof) BEMS are now used in virtually all mechanically
and then daylight illuminances calculated conditioned buildings and increasingly in nat-
(using measured daylight factors) for vari- urally ventilated buildings. Potentially they have
ous switching or dimming zones in the the ability to control energy use and record en-
building. This is a centralized system and ergy consumption, as well as controlling the
would be part of the building energy internal environmental conditions.
management systems (BEMS). BEMS can be used to control all aspects of
2 The illuminance for each zone is measured the building – lighting, heating and cooling
at a representative point in the zone, and plant, internal temperatures and air quality, ven-
used to control that zone only. Since it is tilation systems, night cooling, optimal start/stop
inconvenient to place the sensor on the and solar control blinds. Most systems have a vis-
workplane facing upwards, it is often placed ual display that can show the operator the
on the ceiling facing downwards. If this is current conditions and settings throughout the
done, it must be recognized the sensor will building and enable them to make modifications.
not measure the actual working illumin- Although theoretically BEMS enable the ef-
ance but the ceiling illuminance, which is ficient control of a building, in practice many
affected by the floor and work-surface re- systems do not give the good results. Poor system
flectance. The latter system is becoming design, poor programming, over-complex sys-
more popular. tems and poor understanding by the operator
84 Practice
can lead to systems being over-

ridden or disabled. Although a
single BEMS can control all en-
ergy and comfort aspects of a
building, using either hard
wiring or radio links, separate
a
sub-systems are sometimes
2% 5% 10% found controlling different
physical or subject areas – for
example, local controls for split-
unit cooling in meeting rooms.
An important design aspect for
the BEMS contractor is to en-
sure that the level of complexity,
and the design of the display and
zone 1 zone 2 operating system, fit the likely
level of knowledge and training
of the person who will be ex-
pected to operate it on a day to
day basis.
room
illuminance
(at ref point) 7.10 Adaptive controls
lux
The principle of adaptive con-
600 trol has been described in some
b
zone 2 detail in section 1.5. Essentially
it is the inclusion of the occu-
zone 1 pant in the control loop, that is,
300 permitting the occupant to take
part in the control process with-
lights off
out allowing the action to
0 destroy the automatic control
occupied day time strategy. The advantage of this
approach is that, given a level of
control, the occupant is much
more tolerant of non-neutral conditions, as il-
Figure 7.7 A daylight factor contour map of a side-lit lustrated in Figure 7.9.
room showing position of two separately switched banks of The inclusion of the occupant in the control
lighting (a) and the resulting switch-on times (b) means that opportunities must be provided – op-
erable windows, blinds, heating/cooling controls,
With the steady reduction of costs of micro-electronics, desk or ceiling fan controls..These are technical
luminaries are now being manufactured with their own or element-based opportunities. Other opportu-
detector – that is, one per fitting. Potentially this offers very nities could be termed behaviour-based, such as
good control, but only provided the switching or dimming a cool ‘chill-out’ rest area, cold-drinks machine,
threshold is set up properly. Pre-set values will not recognize or relaxed dress code.These are also discussed in
the effect of work-surface or floor reflectance. section 1.5.
room Figure 7.8 Room illuminance during the

illuminance
(at ref point)
day for dimming control (A) and on/off
lux control (B), indicating the improved
energy saving for dimming control
600
B
300
A
0
time
occupied day
delivered luminous energy for dimming controls A

and ON/OFF controls B
Two issues dealt with here are feedback and this has been to say ‘if the temperature was right
caretaker function. in the first place, the occupant wouldn’t have
opened the window, so we control temperature
even more closely and don’t provide operable
Feedback
windows’. Note that this answer is dependent on
Figure 7.10 shows the interaction of automatic the conventional (Fanger-based) principle that
control with a common action such as opening there is a ‘right temperature’. However, this oc-
a window. The occupant feels warm, opens the cupant might have just hurried to work, climbed
window, cool air enters and the temperature two flights of stairs and be warmly dressed for
drops, the thermostat calls for more heat, and the the prevailing climate – resulting in a very
occupant forgets to close the window; the ther- slightly elevated core temperature. He/she now
mostat has broken the feedback loop – result, needs a period to ‘cool off ’ – a reassurance to the
energy waste. unconscious that long-term heat balance can be
The conventional engineering response to restored.
Figure 7.9 The

adaptive opportunity stress neutral zone seems
stimulus
to be extended
when adaptive
opportunity is
neutral zone present. When no
opportunity is
present, any
(a) good (b) poor (c) zero departure from the
neutral zone is
time stressful
86 Practice
START Caretaker controls

occupant forgets
occupant feels hot about window This is closely related to issue the above – that is,
it is a function that prevents unnecessary waste
but allows the occupant short excursions into
what might be regarded as wasteful behaviour.
thermostat calls The ability to override automatic control is an
for more heat important feature of adaptive control. Caretaker
opens window control is all about gently returning to automatic
control when it leads to lower energy consump-
tion than the present status.
room cools For example, an occupant wants a higher
temperature. If he/she is lucky enough to have
access to a thermostat, they will quite probably
Figure 7.10 The effect of thermostatic control to break the adjust it to a higher temperature than desired,
natural feedback loop in occupant control under the false impression that it will achieve this
condition quicker. It will then remain at that set-
ting, until the occupant feels too hot, but quite
The correct engineering response should be to possibly prompting him/her to remove some
detect that the window is open and deactivate clothing or even open a window.
the local thermostat, or at least give it a tempor- A caretaker control will only offer the occu-
ary set-back. Only when the window is closed, pant a warmer/cooler option about a long-term
would the original set-point be restored. average value. It will then return to that setting
This system has been installed in the Revival over a time span of about 30–60 minutes. It will
GSIS building to control air-conditioning in the detect the long-term preferred setting from the
perimeter zones with operable windows. occupant’s ‘votes’ with the warmer/cooler but-
Open plan situations create more of a chal- ton, and could even add the sophistication of
lenge to achieve this. However, as we move gradually lowering this in the heating season and
towards the systems described above using digi- raising it in summer (if mechanically cooled).
tal addressing and virtual zoning, response such as This will encourage the occupant to make sea-
this becomes increasing possible even in multi- sonal adaptation to their dress ensemble.
occupied spaces.
Another case where controls can break the 7.11 Hybrid and mixed mode systems
feedback loop is in photo-sensitive lighting con-
trol. Consider the case where a room is equipped This relates to mechanical cooling and air-con-
with moveable and modulating louvre blinds. ditioning and is the term used to describe the
The occupant experiences glare, deploys the intermittent application of mechanical cooling,
blind leaving its modulation at closed. Insuffi- to prevent extreme excursions of high tempera-
cient light is transmitted and the daylight ture. This permits a predominantly passive
detector switches on the artificial lighting, or in strategy to dominate the building’s operation,
the case of manual switch-on, allows the occu- leading to much lower energy consumption than
pant to do so. If this action were prevented by if the building were conventionally air-condi-
detecting that the blind was down, the occupant tioned all year round.
would be obliged to control the blind transmis- This approach is no different in principle to
sion (by adjusting the louvre angle) until there the heating of buildings – which is partial and
was sufficient light. intermittent, and as buildings reduce their heat
Figure 7.11 Use of backup chillers in Daneshill House in the mechanically driven night-ventilation system is not evident to the
occupants
demand because of high insulation, will become It is also a good idea if the presence of com-
increasingly less frequent. fort cooling can be disguised.This is to prevent
Mixed mode is also used to describe a spatial occupant demands for mechanical cooling at
mix – that is, where some spaces may be air-con- times outside the target need periods, in the be-
ditioned (e.g. deep non-perimeter areas, densely lief that it will always increase comfort. The
occupied areas such as lecture theatres, meeting ability to disguise will depend on the systems
rooms, etc.), whereas other perimeter zones may employed. For example cooled floor or chilled
be naturally ventilated only. ceiling panels, can operate without obvious signs.
In both cases, the issue is to make sure that If mechanical fresh air supply is already present,
the predominantly passive operation does not then tempering this air can also be achieved
unduly compromise the performance when op- without advertising the fact.
erating mechanically, and vice versa. This is Where it is impossible to disguise, such as the
largely achieved by controls, and relates closely activation of a chilled air supply that is not nor-
to the issues discussed in adaptive control. mally in operation, then the feedback controls
Other important considerations are to ensure (as discussed in section 9.9) should be in place
that the changeover from passive to mechanical to prevent wasteful use, and to give the occupant
mode takes place at the appropriate point. Oth- some control over the decision to mechanically
erwise there is the risk that the building will cool or not.
become air-conditioned by default, possibly with
an inadequate system.
Renewable Energy Options

8
Refurbishment may provide the opportunity to ment does not offer any particular constraints or
incorporate renewable energy (RE) technology. opportunities. Solar thermal and PV applications
Many applications of RE technology are relatively on angled frames on flat roofs, and on-site wind
independent of building work, and could be turbines, fall into this category.
retrofitted at any time – such as solar panels and
wind turbines.These applications are adequately
described in numerous resources.We concentrate
here on instances where there may be savings to
be made when the RE technology is applied as
part of fabric or services improvements.
The cost effectiveness of RE technology
ranges widely. For example, biomass (wood pel-
let) boilers are close to cost effectiveness, whereas
photovoltaic (PV) applications, where grid con-
nection is available, are a long way from cost
effective. However, this does not negate the value
of them since it is widely recognized that as con-
ventional energy costs rise, and volume
production reduces equipment costs, they will
eventually become cost effective. Meantime it is
essential that experience is gained with real ap-
plications. Furthermore, regulated obligations
now exist in some countries where a fraction of
on-site renewable is required for new develop-
ments, and it is quite likely that similar obligations
will be extended to refurbishment projects in the
future. For example, in the UK where the build-
ing or mechanical services are being extended, 10
per cent of energy demand from renewable re-
sources should be provided where paybacks of less
than seven years are achievable.
8.1 Other renewable energy technologies

Most other RE technologies do not interact
directly with the building and thus refurbish- Table 8.1 overleaf
90 Practice
Table 8.1 Application of various RE technologies and their interactions with building refurbishment
Renewable energy Application Comments

technology
Solar thermal (evac. tube) Upgrading domestic hot water system for Installation may be integrated with roof
hotels, hospitals, schools refurbishment – close to cost effective
Solar thermal (flat plate) Low temperature applications such Even unglazed flat-plate collector can be
as swimming pools effective for this low-temperature application
Photovoltaic Re-cladding panels and roof tiles
Photovoltaic/thermal Re-cladding with air-cooled PV panels. Electricity generation and ventilation
pre-heating. Cooled panels work at higher
efficiency
Photovoltaic Opaque PV used as shading devices Geometry for optimum collection and shading
tends to coincide
Photovoltaic Semi-transparent PV used for reduced Not optimum shading since PV is about 85%
transmission glazing panels in large absorber and re-radiates absorbed energy
spaces such as atria inwards
Biomass heating Biomass heating requires space for fuel Local emissions regulations need consulting
delivery and storage
Ground source heating Uses a heat pump Operates at low temperature requiring an
appropriate delivery system, normally underfloor
heating
Ground source cooling Uses a heat pump Increases efficiency of refrigeration due to lower
temperature cold sink. Displaces electricity. Often
used in conjunction with heating
Solar thermal (cladding Re-cladding in conjunction with Heated air collected between lightweight
collector) external insulation absorber and external insulation – best for
ventilation pre-heating
Solar thermal (evac. tube) Contributing to space heating in Installation may be integrated with roof
buildings with low heat demand and refurbishment – not yet cost effective
integrated storage system
Note: A number of innovative techniques (examples are the last two in the table) have been attempted from time to time but as yet are unlikely to prove cost effective.
Part Three Case Studies

The Albatros, Den Helder,

9 The Netherlands
Double skin applied to residential tower from the 1970s in sustainable
conversion to offices
‘The Albatros’ is a high-rise block of seven floors • Any over-cost of eco-refurbishment to be
(4400m²) with a ground floor of meeting rooms, minimized.
reception and circulation (1800m²).The original • Internal conditions satisfying all newbuild
building, built in 1972, had the major glazed criteria.
facades orientated east–west, single glazing in
aluminium frames, no wall insulation, inefficient
Refurbishment strategy
artificial lighting, heating by radiators and gas
boilers, and a mechanical ventilation system The application of insulation to the original
without heat recovery. The building was origi- building, either inside or out, would have re-
nally used as housing for officers of the Royal sulted in many thermal bridges, for example
Dutch Navy and had very high energy con- where internal partitions meet the external wall
sumption. and where the balcony meets the external wall.
This suggested that the insulation of the facade
Objectives should be based on a second skin applied over
the existing skin and supported by the existing
• 30 per cent reduction in energy demand balcony structure. The change of use to offices,
compared with current newbuild regulations. with increased occupancy density compared
• 30 per cent energy supply from renewable with residential use, underlined the need for
sources or a 50 per cent reduction in overall good daylighting and energy efficient ventila-
energy use. tion.
Figure 9.1 The Albatros before (left) and after refurbishment

94 Case Studies
Table 9.1 Different refurbishment specifications
Consolidate Upgrade Second skin New Preliminary design

facade second skin facade
glazing glazing panels new windows with new wooden low-e glazing in existing facade with
in front of low-e glazing frames with wooden frames new openable windows
existing facade low-e glazing
insulation insulation of insulation of insulation of insulation of
opaque envelope opaque envelope opaque envelope opaque envelope
airtightness improve airtightness improve airtightness improve airtightness
of facade of facade of facade
ventilation high efficiency nat. supply self- nat. supply self- nat. supply self-
heat recovery balancing vents, balancing vents, balancing vents,
mech exhaust mech exhaust mech exhaust
heating condensing gas heat pump and heat pump and heat pump and
boiler condensing gas condensing gas condensing gas
boilers boilers boilers
lighting high efficiency high efficiency high efficiency high efficiency
lighting lighting lighting lighting
interior walls existing new all new construction new
Note: ‘New’ includes demolition and new structure.
An important strategic issue was that options, A summary of the final design choice is as
shown in Table 9.1, should be selected on the follows:
grounds of life-cycle performance; that is, total
embodied and consumed CO2. However, con- • new glazing and aluminium frames with U-
trary to normal practice, a single (long) assumed value 2.2W/m2°K;
building lifetime was not used; rather, options • second skin with sun shading in cavity;
were considered at various future dates to see • insulation of the existing opaque envelope
how savings evolved.This is illustrated in Figure with U-value 0.3–0.4W/m2°K;
9.2.The performance as indicated by total CO2 • passive ventilation system with wind pressure
emissions (embodied + service) as a percentage – independent vents;
of the existing building – for example, the 40- • district heating with waste heat from on-site
year bar for the ‘preliminary design’ indicates a power station;
reduction of 60 per cent compared with the 40- • heating with convectors in offices;
year total for the existing building. Note that all • lighting capacity 12W/m2 with photo sensi-
measures in ‘consolidate’ and ‘upgrade’ more than tive dimming control.
recover the invested CO2 within five years,
whereas the ‘new’ requires more than ten years. The double skin
The ‘preliminary design’ took the most promis-
ing features from the other scenarios. The second skin is hung in aluminium framing
The Albatros, Den Helder, The Netherlands 95
Figure 9.2 Total

embodied and service
CO2 (as percentage of
existing building) for
different refurbishment
specifications, and for
time spans of 5, 10, 25
and 40 years
onto the existing steel balcony structure. The

steel structure was first removed to allow the cold
bridges to be insulated.The existing single glaz-
ing is replaced with low-e double glazing in new
thermal-break, openable aluminium frames.
The active second skin consists of 66 per cent
of toughened single glazing and 34 per cent ven-
tilation grill controlled by the building energy
management systems (BEMS). In winter, the large
outer vents are almost closed, and self-balancing
ventilation1 inlets in the inner skin (original en-
velope) allow pre-heated ventilation air to be
drawn into the building.Air is extracted mechan-
ically via extract grilles in the ceiling and on to a
heat recovery unit and heat pump.The section is
shown in Figure 9.4 and a simplified elevation in
Figure 9.5. Note that, moving horizontally, the
grills alternate the function of inlet and outlet,
minimizing the risk of short-circuiting.
Figure 9.3 The second skin. The walkway grid is at cill

level; there is airflow from the inlet below the grid, to an
outlet above the ceiling grid
1 As the pressure difference across the vent increases, e.g. due to wind, the aperture closes up resulting in an almost wind-
independent flow rate.
96 Case Studies
In summer, the large inlet and outlet grilles in

the second skin are open to allow high ventila-
tion rates of the void, to keep temperature
increment above ambient to a minimum. Extra
vents in the inner skin open under BEMS con-
trol to allow night ventilation, driven by extra
fans extracting from the corridor outside the of-
fices. When the solar irradiation is greater than
200W/m2, louvered blinds with a total transmis-
sion of 20 per cent are deployed in the double
skin void on the inside of the outer glazing.
Performance of double skin

The thermal performance of the double skin in
winter relies upon the increased temperature in
the void compared with the outside temperature.
This leads to reduced heat loss across the original
facade, and reduced ventilation heat loss also, al-
though drawing in cold air to replace that taken
by ventilation will reduce the temperature in the
void.The temperature in the void is elevated for
two reasons – firstly heat loss from the heated
building, and secondly from solar gains when they
are present.Thus the double skin system has both
a heat recovery function (sometimes referred to
as dynamic insulation) and solar collection.
In order to investigate the potential contribu-
tion in this mode, temperatures were monitored
in the room, the void and outside, and are shown
in Figure 9.6.Temperature in the void is seen to
track the outside temperature quite closely (ex-
cept on sunny days), with an average increment
of less than 3°C. In seeking an explanation for
this disappointing performance, it was discovered
that the large summer ventilation grills were not
closing properly and the void was being venti-
lated at much higher rates than necessary. The
BEMS was also opening the vents in the day-
time, as late in the year as October. Both of these
errors have now been corrected.
Ventilation and heating

Ventilation has already been partly described in Figure 9.4 Section showing second skin and ventilation
connection with the double skin.After the air is openings
occupant, but is closed automatically at night in

winter. Air is then extracted from the room by
OUT IN OUT IN OUT mechanical exhaust. Heating is provided by a
natural convector installed at skirting level on the
outer wall (see Figure 9.4).The emitter is gener-
ously sized, allowing a water temperature of only
55°C.
Performance
Indoor air quality was assessed by CO2 measure-
ment and it was shown that the hybrid
ventilation scheme (mechanical extract, passive
supply) was very effective. Figure 9.7 shows a
typical trace for a 50-day period, during winter
OUT IN OUT IN OUT 2007, for one of the west facing offices.The daily
occupancy pattern is clearly visible, and it is ev-
ident that peak concentrations are never higher
Figure 9.5 Simplified elevation showing alternate inlets
than 900ppm, whilst average during the occu-
and outlets
pied period is about 650ppm. These are very
good compared with 1200ppm (the generally
permitted level), and also compare well with the
pre-heated in the double skin, it enters the office design target of 1000ppm. However, the occu-
room at high level above the head of the win-
dow. Being cooler than room air, it descends in
a turbulent plume and mixes with the warmer Figure 9.6 Temperature measured in the office, the double
room air. This vent can be operated by the skin, and outside for period 18–27 October 2007
25
20
15 T facade
degree C
T office
10 T outside
0
18-10- 19-10- 20-10- 21-10- 22-10- 23-10- 24-10- 25-10- 26-10- 27-10-
2007 2007 2007 2007 2007 2007 2007 2007 2007 2007
0:00 0:00 0:00 0:00 0:00 0:00 0:00 0:00 0:00 0:00
date
98 Case Studies
pancy density is low, with a global space provi- ify high reflectance finishes to all room surfaces
sion of 28m2/person. and all surfaces in the second skin void.
There was some concern that on the occa- Figure 9.8 shows the resulting daylight factor
sion of strong easterly or westerly winds, there (DF). Two important results are evident; firstly
might be cross-contamination between offices, the DF does not drop below 2.5 per cent, and
leading to higher concentrations on the down- secondly that the rise to approximately 14 per
wind side.This was checked with tracer gases and cent at the window is modest for a side-lit room,
it was found that the movement of air between and is gradual.These characteristics are positive
the zones is no more than 10 per cent of the attributes for both daylight quantity and quality.
fresh air flow into each room. These measure- They are achieved partly due to the high inter-
ments also showed that the overall ventilation nal reflected component from the highly
rate was around 0.65ac/h.This is quite low, but reflective surfaces, and partly due to the over-
the fact that there is very satisfactory air quality hanging and reflective structures (including the
proves that with good spatial efficiency (i.e. ven- shading louvres) located in the second skin void.
tilation where it’s needed) low ventilation rates These structures have the effect of redirecting
are acceptable – leading to low ventilation heat light onto the ceiling and side walls, and thence
loss and fan power. by reflection to the back of the room.
The artificial lighting installation is of high ef-
Daylighting ficiency high frequency sources and luminaires.
The installed capacity is high at 12W/m2, with a
Lighting energy typically forms a large propor- design illuminance of 500 lux. There is photo-
tion of total energy use for offices so a strategy sensitive dimming control to two banks of
for maximum use of daylight was adopted in the lighting at 1.5 and 4.5 metres away from the
Albatros refurbishment.The potential was good, window. There is no occupancy detector, but
since the cellular offices are only five metres deep there is an automatic switch-off at 1230 and
and the existing glazing area was large (more 1800 hours. Switch-on is manual.
than 65 per cent of facade). However, the addi-
tion of the second skin, together with shading Overall energy performance
devices and the existing balconies, could cause
significant obstruction. The energy use of the building, heat and elec-
The design solution adopted was to keep the tricity, was monitored for the period October
full width, cill to ceiling glazed area, and to spec- 2006 to October 2007. Table 9.2 compares the
1000
800
Figure 9.7 Measured
CO2 concentration for
600
office B3.07 west, for
CO2 [ppm]
50-day period in winter

400 2007
200 office B3.07 west
0
17-2-2017 27-2-2007 9-3-2007 19-3-2007 29-3-2007 8-4-2007
0:00 0:00 0:00 0:00 0:00 0:00
16
14 office A3.07 east Figure 9.8 The daylight
12 factor profile for a typical
10
office
8
DF [%]
6
4
2
0
0 1 2 3 4 5
metres from window (1st skin)
measured consumption with the original calcu- Secondly, the actual internal gains from
lations, with a new building built to current equipment in the building were much lower
regulations, and an average office building for the than that assumed in the calculations.Thirdly, it
Netherlands. The measured heat has been cor- was found that the BEMS was calling for heat
rected for the actual degree days, to the for 24 hours per day, 7 days per week.This had
long-term value used in the predictions. been set up to cover out of hours use; in future
this will be achieved by a special override switch.
Correcting for a conventional office occu-
Table 9.2 Energy use in delivered kWh, October 2006 to
pancy profile reduces the annual heat demand by
October 2007
about 44 per cent which brings it into the re-
Heat Fans Lighting gion of a new office building. It is anticipated
that the correction of the technical fault with the
Albatros predicted 65 6 15
closure of the ventilators will reduce this further.
Albatros measured 154 2.2 3.6 The electrical consumption (Table 9.2) shows
the reverse, being lower than calculated, and sub-
Albatros corrected for
stantially lower than new office buildings. For
standard occupancy 86 1.2 2.0
lighting, this is explained by the excellent day-
new office building 80 8 20 light environment in the rooms, together with
dimming controls and efficient sources and lu-
average office building 150 12 30
minaires. The low consumption for fan use,
together with very high air quality, underlines
The first impression is that the heating perform- the effectiveness of the hybrid ventilation
ance is disappointing. However, three main scheme and its spatial ventilation efficiency. Fig-
explanations have been put forward. Complaints ure 9.9 shows the breakdown of fan energy use,
of cold discomfort from the inlet vents in the of- and draws attention to the high proportion for
fices led to an inspection of the closure of the toilets. Bearing in mind the intermittent use of
large vents in the second skin and they were toilets, this suggests that a more sensitive control
found to be partially open. The resulting low might make further savings. It is reassuring to see
temperatures, measured directly, as shown in that night ventilation (which successfully
Figure 9.6, were the result of an overlarge venti- provided daytime comfort temperatures) repre-
lation rate to the second skin void. sented a very small energy cost.
100 Case Studies
fresh-air inlets. It is not clear why 40 per cent re-
0.81
ported dissatisfaction with air quality, since the
objective measurements suggested that it was
high.
The strong dissatisfaction with the acoustics
Day ventilation with
heat recovery
1.36
was due to a very specific problem. Small holes
summer/night
0.04
in the second skin resulted in wind-driven reso-
toilets
nance producing an irritating sound. This has
now been corrected.
Figure 9.9 Electricity for daytime ventilation, summer night Finally, there seems to be clear agreement that
ventilation, and toilets the daylighting is very good, although since in
Note: Units are kWh/m2yr.
the question daylight and view had been com-
bined, it is not clear if the visual obstruction of
the second skin and shading devices has caused
Comfort some negative impact on view.
Objective measurements show that the prevail- Conclusions

ing winter and spring temperature in the rooms
was 20–22°C.Vertical gradients were no larger The Albatros project has demonstrated the via-
than about 2°C.The results of occupant survey bility of the application of a second skin to an
questionnaires are shown in Figure 9.10. over-glazed, leaky and poorly insulated 1970s
These results show quite a high level of dis- tower block.The monitoring has, as is often the
satisfaction. In particular winter heating comfort case, shown up a number of malfunctions which
was poor with 25 per cent reporting high dissat- have had some serious effects both on energy use
isfaction. This was related to over-ventilation of and user satisfaction. However, the causes have
the double skin void, already referred to, leading been identified and corrected and the building
to low air temperature and draughts from the should now return a much better performance.
Temperature winter Figure 9.10 Occupant

survey conducted in spring
Temperature spring
2007
Controllability temp
Indoor air quality
(Day)light and view
Acoustics
0% 20% 40% 60% 80% 100%
very dis. dis. neutral satis. very satis.

Lycée Chevrollier, Angers, France

10 Major fabric renovation improves insulation and shading to
33,000m2 building
The Chevrollier High

School was built in 1959.
This large school houses 500
teachers, and 2700 students
from sixth grade to school
leaving age, providing both
academic and vocational ed-
ucation. The building had
never been refurbished and a
number of problems were
evident:
• Overheating in the
south-facing classrooms.
• Degraded poorly fitting
windows resulting in
high infiltration.
• Uninsulated fabric and
poor heating controls re-
sulting in thermal discomfort. Figure 10.2 Plan of the refurbished and newbuild work
Other problems relating to the fabric of the

building included failure of some reinforced
concrete elements, the degradation of finishes,
and the presence of asbestos in certain areas. Fur-
thermore, there was no mechanical ventilation
system installed in the classrooms, now manda-
tory in French schools.
Strategy for sustainable refurbishment

The shallow plan of the building results in a very
large surface area and this, together with high U-
value and infiltration rate, made improvement to
the thermal performance of the envelope a high
Figure 10.1 The original south elevation of the Lycée priority. However, the shallow plan also means
Chevrollier, Angers, France that there is good availability of daylight over the
102 Case Studies
floor plan. This could realize electrical energy • Daylight and occupancy sensitive lighting
savings due to reduced artificial lighting loads, controls.
provided appropriate control systems were in- • High efficiency sources and luminaires.
corporated. Finally the problem of overheating
in the south-facing classrooms needed to be ad-
C. Comfort: Shading and ventilation
dressed.
• Shading of whole south facade with fixed ex-
Main low energy measures ternal louvres.
• Mechanical extract ventilation with passive
A. Thermal inlets controlled by BEMS, with night venti-
lation.
• Externally applied insulation to east, north
and west, internally applied to south wall re-
ducing the wall U-value from 2.0W/m2°C to D. Other features
0.39, insulation to roof from 3.5 to 0.23, and • Photovoltaic array installed on roof of new
floor, where crawl space allowed, 2.1 to 0.16. block.
• High performance low-e double glazing in • Use of low volatile organic compound
thermal break aluminium frames with a U- (VOC) emission finishes.
value reduction from 6.0 to 1.9W/m2°C. • Management (sorting) of building waste to
• Reduced infiltration rate due to replaced permit recycling.
windows and fabric cladding.
• New low NOX emission gas boilers. Insulation
• New unheated atrium between original
building and new block. The original envelope was comprehensively in-
sulated as shown in Table 10.1. All cold bridges
were insulated by external insulation except for
B. Lighting
the south facade where the visual intrusion on the
• Improved daylight distribution in third floor exposed original facade was considered to be un-
classroom due to secondary lighting from acceptable. Floor insulation was possible for only
north facade. a relatively small proportion of the building, where
Table 10.1 Specification of envelope insulation before and after refurbishment
Before refurbishment After refurbishment
composition U-value W/m2°K composition U-value W/m2°K

wall sandwich panel > 2.0 W,E,N – external
S – internal insulation 0.385
roof no insulation > 3.5 insulation 0.233
glazing and frames single glazed steel frame > 6.0 low-e double aluminium
thermal break 1.9
floor 1 on soil no insulation 2.0 no insulation 2.0
floor 2 over crawl space no insulation 2.4 insulation underfloor 0.16
Note: All cold bridges treated except on south facade.
Lycée Chevrollier, Angers, France 103
NORTH DAYLIGHT
PV
NEW BUILDING BUILDING BUILDING TO BE TO BE

TO BE TO BE REFURBISHED REFURBISHED REFURBISHED
REFURBISHED HEAVILY +
EXTENSION
tion. It has a major visual impact on the build-

Figure 10.3 Diagrammatic section showing daylight and ing. In addition to this, the replacement glazing
shading strategy was high performance selective transmittance
type with a total transmittance of 40 per cent.
The shading geometry is such that no direct
there was sufficient crawl space to give access to sunlight penetrates the facade from March to
attach insulation to the underside of the floor. September. This provides an effective shading
transmission coefficient of about 25 per cent.The
Daylight and artificial lighting aluminium louvres are finished on both upper
and lower surfaces with an off-white paint of
The overall daylight strategy is illustrated in Fig- high reflectance. This causes some of the inter-
ure 10.3. It shows the provision of extensive solar cepted sunlight to be inter-reflected between the
protection on the south facades of the new south louvres and redirected to the back of the room,
block and the long refurbished block. It also improving the daylight distribution.
shows the access to north light to the corridor of The second intervention (on the top floor
the refurbished block, and to the two new work- only) was to reinstate and enlarge secondary day-
shop blocks via north-facing roof lights. lighting openings in the back wall adjacent to
Although the original classrooms (south side the corridor which itself was lit by high level
of old three-storey block) had adequate areas of clerestory windows. It is well established that a
glazing, the daylighting quality was poor. This small increment of daylight factor (DF) where
was because there was a high illuminance gradi- the DF is lowest can have a considerable benefit.
ent from the glazed facade to the back of the This is because of the reduction in DF ratio.
room (5.5 metres), exacerbated by the lack of Finally, all of the new room surfaces were of
shading other than internal curtains.The draw- high reflectance. This leads to a high internally
ing of curtains to reduce glare interfered with reflected component (IRC) of the daylight, also
ventilation and obstructed view, and often re- contributing to reducing the DF gradient across
sulted in the lights being switched on. the room, as well as increasing the average illu-
Two major interventions were made. Firstly minance level.
the installation of 8500m2 of fixed horizontal
louvre shading onto the outside of the south fa-
Artificial lighting
cade. This was first tested over a small area, and
following the successful test was installed over The light fittings in the refurbished classrooms
the whole facade without significant modifica- are high efficiency fluorescent sources in low-
104 Case Studies
glare luminaires complying with French Codes Ventilation

of Practice for educational buildings.The design
illuminance is 500 lux. No special provision was made in the original class-
In order to realize the energy saving potential rooms for ventilation other than openable windows.
of daylight, artificial lighting must be switched In winter, usually windows were shut, but the high
off when daylight is available. Manual switching level of infiltration through the badly fitting steel
in multi-occupancy rooms is very ineffective in windows gave sufficient fresh air to maintain a rea-
this role, so light and occupancy sensitive con- sonable air quality. However, this infiltration was
trols have been installed. uncontrolled, and led to over-ventilation and sub-
The luminaires are arranged in two banks sequent waste of heat during times of high wind
running parallel to the window wall. They are and when the room was unoccupied.
controlled by a manual switch – switching the The upgrading of the envelope included new
whole room, with an occupancy detector, and airtight windows, thus removing this ‘fail-safe’
an illuminance detector controlling each bank background ventilation. This was replaced by a
separately. The latter is to respond to the de- hybrid mechanical ventilation system under the
creasing DF with distance away from the control of the BEMS. In each classroom there is
window. mechanical extract, with passive inlets under
The control logic is as follows: BEMS control.
In principle the system can respond to vary-
room unoccupied lights always off ing demands made on ventilation rate:
room occupied/daylight lights under on/off control in Status ac/h
banks (initial manual switch-on) Unoccupied 0
room occupied lights on (manual switch-on) Occupied 1
Heavily occupied 3
Night ventilation 6
Performance
In most classrooms the perceived daylight qual- The night ventilation is controlled as follows:
ity is excellent. There are some exceptions in
block F on the ground and first floor where the Night Vent ON between 2200 and 0600 hours
overshading by the new block C, together with IF internal temp > 19oC
the obstruction of high angle sky by the shading AND internal temp > external temp + 2
louvres, has lead to a low average value of DF.
Unfortunately the consumption of lighting The cool night air can make contact with the
has not been separately metered, and so it is not thermal mass of all wall surfaces except the inside
possible to disaggregate the contribution of the of the south facade (due to internal insulation),
daylighting and the control system. There have and the ceiling slab where there is a suspended
been some problems with setting up the photo- ceiling.The floors are treated with sheet vinyl and
sensitive control.The on/off control has caused linoleum also permitting good thermal coupling
annoyance to the occupants, to the extent that with the floor slab.
in some cases, teachers have drawn the curtains
to ensure that the artificial lighting stays on.This Performance
problem will be eliminated when the intended
dimming control is installed. Figure 10.4 shows the evolution of temperature
and CO2 for one of the classrooms in block E,
in January. The response of both, with the CO2
CO2 & temperature variation

E107 Figure 10.4 Temperature and CO2 concentration during
2100 24
one hour of occupancy of classroom in building E
1900
23
1700
1500 22 CO2
1300 °C temperature
ppm
1100 21
900
20
700
500 19
10:04 10:19 10:33 10:48 11:02 11:16
Time
going far above acceptable levels, suggests that

the ventilation is not operating correctly.
Generally, the air quality and temperature
control is poor.This points to inadequate venti-
lation. The mechanical system is specified to
deliver 3ac/h when the classroom is fully occu-
pied. This gives a maximum fresh air per student
of 3.5l/s compared with a recommended mini- Figure 10.5 The atrium formed between new building C
mum of about 9l/s.Although there are openable on the left and refurbished block G on the right
windows, safety regulations prevent them from
being opened widely.
In winter, the large doors and the roof vents
The atrium will be kept closed. No mechanical heating is
provided, but the temperature is elevated above
The atrium, Figure 10.5, is located between the the outdoor temperature due to heat losses from
old building G, and the new building C which the surrounding buildings, and solar gains if avail-
forms the south and west walls of the atrium. able, and never falls below 10°C.This results in
The east wall and the roof are predominantly reduced heat losses from the adjacent buildings.
glazed.The east also contains the bridge linking Artificial lighting is provided by eight spot-
the old and new blocks at high level. lights directed up onto downward facing
At ground level, the atrium includes the un- reflectors. There is some concern that this is a
dercroft beneath the new building C and the old wasteful system due to a large proportion of the
building G, and thence to the outside via large light missing the reflector.
glazed industrial type doors (Figure 10.6). In The atrium has an important social function,
summer these are open, together with large vents acting as a meeting space, information point, and
in the roof under BEMS control. There is no on occasions a space where events and perform-
shading, but these large openings are sufficient ances take place. This is a good example how a
to keep summer temperatures to within accept- low cost space (no servicing, little new structure)
able limits. can be of great value.
106 Case Studies
NATURAL VENTILATION
DAYLIGHT
PV ATRIUM
SOLAR
PROTECTION
ON SOUTH
FAÇADE
NEW BUILDING EXISTING BUILDING
Figure 10.6 Ventilation openings in the roof of the atrium,

The design and specification of all new com-
under BMS control, and large openable doors at ground
ponents (both in the new building and the
level give high rates for summer ventilation
refurbishment) were chosen to minimize on-site
waste, and with a view to their own recycling at
the end of their life.The waste generated by the
Photovoltaic panels building in use was also considered and the de-
sign provided special recycling areas for valuable
The panels (78m2) were originally to be wastes such as paper and aluminium.
mounted on the roof of the atrium to provide The local environmental impact of the mater-
shading, but after technical problems it was de- ials used in the new building and the
cided to move them to the roof of block C refurbishment were also given special consider-
(Figure 10.7).Their output was monitored from ation. Long-life finishes that required minimum
17 July 2006 to 7 April 2008 and corrected for chemical cleaning, and low VOC emission
an average year. materials such as linoleum were specified.
Table 10.2 Performance of PV installation
Surface area Total energy Energy/m2 Total CO2

m2 PV panel kWh/y kWh/y displaced
kg/y
78 7666 98 3449
Waste management and other

environmental issues
During the demolition that was part of the re-
furbishment, a lot of waste material was
produced, including hazardous waste such as as-
bestos. Wastes produced were recorded and
segregated by type, allowing efficient recycling Figure 10.7 78m2 of photovoltaic panels installed on the
where possible, and efficient disposal where not. roof of the new block C
gas consumption electricity consumption

4,500,000 1,400,000
4,000,000 1,200,000
3,500,000
1,000,000
3,000,000
Kwh
800,000
Kwh
2,500,000
2,000,000 600,000
1,500,000
400,000
1,000,000
200,000
500,000
0 0
2000 2001 2002 2003 2004 2005 2006 2007 2000 2001 2002 2003 2004 2005 2006 2007
year year
Figure 10.8 Total gas consumption 2000 to 2007. Figure 10.9 Total electricity consumption for 2000 to
Includes estimated 240,000kWh for cooking 2007
Overall energy performance been diluted by heating in other areas which

have had less improvement, and other gas con-
Gas consumption suming activities such as cooking which have not
changed. When this is taken into account, it is
The annual gas consumption in Figure 10.8 has estimated that the reduction for blocks E and F
been corrected for the variation in degree days alone would be about 45 per cent.
from 2000 to 2007, and is quoted per m2 to take
account of the increase of heated space. It shows
a significant reduction of 31 per cent for the year
Electricity consumption
heating season 06/07. The annual electricity consumption in Figure
Bearing in mind the dramatic reduction in 10.9 shows a relentless increase.There are several
fabric heat loss, this is rather less than may have explanations for this. Firstly the area has increased
been expected.There are two probable explan- by nearly 30 per cent. Secondly the small power
ations. Firstly there have been problems with loads have increased due to the installation of
heating controls in some classrooms following computers, multimedia equipment, machine tools
damage and failure of the local radiator thermo- and general electrical equipment.There must also
stats. This has led to overheating and then be an energy penalty for the increased use of me-
wasteful ventilation by window opening.Ther- chanical ventilation.These will mask the effect of
mostats are being changed to make them more the reduced electrical consumption for lighting,
robust and tamperproof. which unfortunately was not metered separately.
The other likely cause, common to many re-
furbishment projects, is that the heating standards
have improved. This is not normally accounted
CO2 emissions
for when comparing before and after, since, as in The emissions have been calculated using a
this case, temperatures and thermal satisfaction European average value for the CO2 conversion
were not recorded in the original building. factors for kWh to kg CO2.These are:
Finally, the effect of the improved fabric in-
sulation to blocks E and F, where the largest 1kWh electricity 0.44kg CO2
changes were made in fabric insulation, have 1kWh gas 0.19kg CO2
108 Case Studies
Table 10.3 shows the comparison for 2000 and Table 10.3 CO2 emissions for 2000 and 2007
2007.
2000 kWh Emission kg CO2
Comfort electricity 860,332 0.44 378,546

gas 3,726,436 0.19 708,022
450 questionnaires were circulated to the stu-
dents. 57 per cent were returned and the results total 1,086,568
are shown in Table 10.4.These figures are for the
2007
whole building including the new part. It shows
that satisfaction is 65 per cent and 55 per cent electricity 1,305,603 0.44 574,465
for winter thermal comfort and ventilation, but
gas 2,746,606 0.19 521,855
drops to 47 per cent and 44 per cent in summer.
Satisfaction with daylight is high, at 85 per cent, total 1,096,320
Table 10.4 Post occupancy evaluation from the students for the whole school
Thermal comfort Winter satisfaction Yes 167 65%
No 88 34%
NA 1%
Summer satisfaction Yes 121 47%
No 122 47%
NA 6%
Ventilation Winter satisfaction Yes 142 55%
No 109 42%
NA 3%
Summer satisfaction Yes 114 44%
No 129 50%
NA 6%
Natural lighting Satisfaction Yes 219 85%
No 33 13%
NA 12%
Curtain operation Yes 155 60%
No 90 35%
NA 5%
Artificial lighting Satisfaction Yes 119 46%
No 134 52%
NA 2%
Table 10.5 Post occupancy evaluation from teaching staff

Build C Build E Build F Build H Global
Number 14 15 3 2 36
Thermal comfort winter
satisfaction YES 11 79% 10 67% 1 33% 0 0% 22 61%
NO 3 21% 5 33% 2 67% 2 100% 14 39%
summer
NO 5 36% 8 53% 1 33% 1 50% 16 44%
Ventilation winter
NO 6 43% 10 67% 2 67% 0 0% 22 61%
summer
NO 7 50% 8 53% 3 100% 1 50% 24 67%
Natural lighting summer
NO 3 21% 2 13% 1 33% 0 0% 6 17%
curtain
operation YES 6 43% 11 73% 1 33% 0 0% 20 56%
NO 5 36% 3 20% 2 67% 1 50% 11 31%
Artificial lighting satisfaction YES 7 50% 9 60% 1 33% 0 0% 18 50%
NO 7 50% 6 40% 2 67% 2 100% 18 50%
but drops to 46 per cent for artificial lighting, Conclusions

probably reflecting the problems with the photo-
responsive controls. The impression on visiting Lycée Chevrollier is
Unfortunately, the student survey was not car- that you are visiting a new building.The level of
ried out building by building. However, this data refurbishment is so high, that one is not aware of
is available from the teachers only, and is pre- where the original building finishes and where
sented in Table 10.5. It follows a similar pattern the 30 per cent increase in area begins. Clearly
but with much stronger criticism of the ventila- there has been a huge investment in money and
tion and summer comfort in blocks E and F.This embodied CO2, yet there has also been a great
is consistent with the CO2 and temperature saving in all of the original CO2-rich materials
measurements shown in Figure 10.3. such as concrete and steel.
The CO2 emissions for 2007, calculated using
the standard European average, show no reduc-
110 Case Studies
tion from the 2000 value. However, the building

is 30 per cent larger, and undoubtedly is serviced
to a higher standard and contains far more en-
ergy-consuming equipment.
The difficulties with commissioning, which
undoubtedly explain the poor performance in
certain areas, are often experienced in new
buildings and are not related specifically to re-
furbishment. Most of these problems have now
been identified and will be corrected in the near
future. As is usual with newly commissioned
buildings, we can expect a steady and significant
increase in performance as these problems are
solved.
Daneshill House, Stevenage, UK

11
Phase change material installed in lightweight office interior to increase
thermal mass
Daneshill House is a purpose-designed local gov- The new block, built in the 1980s, has a concrete
ernment office building of 6898m2 gross area, the frame and slab, and insulated brickwork cladding
larger part constructed in the 1950s as part of the with a U-value of 0.45W/°Cm2.The small win-
Stevenage ‘new town’ development. The old dows have high quality double-glazed units and
block is a concrete-framed building originally internal solar blinds.
clad with single glazed curtain walling, with
openable windows. It was refurbished in the Strategy for refurbishment
1980s and 67 per cent of the cladding which was
single glazed had its thermal insulation improved Three distinct areas of the building were consid-
with secondary glazing and the outside pane re- ered – general offices in the old block, offices in
placed with tinted glazing in an attempt to reduce the new block, and a Customer Service Area, also
solar gains.The opaque part of the wall (33 per in the new block.The main objective was to ad-
cent) was insulated to give a U-value of dress the problems of overheating in the old
0.45W/°Cm2. However, this part still suffers from block. In common with many buildings of this
severe overheating in summer (Figure 11.1). type, summer overheating was a serious problem,
exacerbated by ever increasing gains from equip-
ment, and a series of above average summer
temperatures. Air-conditioning had been in-
stalled in the new block from new, and there was
considerable pressure to retrofit air-conditioning
in the old block.
Another area of concern in the old block was
the electric underfloor space heating system,
which apart from poor control, had, due to its
energy source, very high CO2 emissions. It was
replaced with a gasfired radiator system. Day-
lighting controls were also introduced in all
office areas together with an innovative light
emitting diode lighting scheme in the Customer
Service Area. Finally the electric domestic hot
water system was replaced by a gas boiler, to-
gether with a solar water heating array.
Figure 11.1 The Borough Council Offices built in the
1950s as part of the New Town of Stevenage. The original
block (on the right) was refurbished in the 1980s and a new
block added (left).
112 Case Studies
Figure 11.2 Stevenage Borough Council Offices interior

after refurbishment Figure 11.4 The CoolDeck system: Air is drawn between
the concrete slab and metal trays containing PCM
Main innovative energy saving features
unconventional approach, where thermal cou-
The CoolDeck system pling with the deck was achieved by fans
The open plan, carpeted floor and suspended drawing cool night air into the ceiling void, as
ceiling in the old block did not lend itself to in Figure11.3. In addition, the effective thermal
conventional passive cooling options of night mass was increased by including phase change
cooling, since the thermal mass of the floor slabs material (PCM).1 This system is referred to as
was isolated from the interior.This called for an CoolDeck (Figure 11.4).
Slab
CoolDeck + PCM High turbulent High rates of surface

air flow heat transfer
suspended ceiling
Figure 11.3 The thermal mass is coupled to the room air by fans drawing air over the concrete slab in the ceiling void. At night,
outside air cools the room and slab. In the day, room air is circulated via the cooled slab
1 Phase change refers to the melting or solidifying of a material. Phase change materials behave as if they have very high
thermal mass at and around their melting temperature.
Daneshill House, Stevenage, UK 113
Figure 11.4 shows air being drawn between the

concrete slab and the metal trays containing
PCM. The turbulent flow increases the surface
heat transfer between the air and the slab and
PCM. At night-time, outdoor air is delivered to
the room by window mounted fans, and then
drawn into the ceiling void to cool down the slab
and ‘freeze’ the PCM. In the daytime the room
air is cooled by flowing over the slab and PCM.
The trays cover only 15 per cent of the slab
area but it is calculated that by including the
PCM the available thermal mass has been effec-
tively doubled.
The PCM is based on calcium sulphate and
water, with additives to ‘fine tune’ the transition
temperature to 24°C. It is held in plastic sachets
which can be removed from the metal trays, as
shown in Figure 11.5.
Figure 11.5 Plastic sachets containing PCM
Performance
The summers of 2003 and 2005 had tempera- impossible to meet the Chartered Institute of
tures well above average.The CoolDeck system Building Services Engineers (CIBSE) criterion,
alone did not lower temperatures sufficiently and of less than 1 per cent occupied hours above
complaints of discomfort were prevalent after 28°C, with CoolDeck alone.
sequences of hot days, when night-time temper- It was decided to add top-up cooling to the
atures did not drop below 22°C. Simulation with air by local direct expansion (DX) chilling units
up to date climate data showed that it was located in the ceiling void (Figure 11.6) to
Figure 11.6
Floor plan
showing the
DX units
(green) and
distribution
ducts providing
cooling top-up
114 Case Studies
Table 11.1 Comparison between conventional air-conditioning, CoolDeck, and CoolDeck plus top-up cooling
Air-conditioning (1) CoolDeck (2) CoolDeck with top-up (3)
annual annual difference annual difference

kWh CO2(kg) kWh CO2(kg) CO2(kg) % kWh CO2(kg) CO2(kg) %
17,512 7530 3468 1491 6039 80 4468 1921 5609 74
ensure that the temperature of the PCM and the The pre-conditioning control logic is illustrated
slab were lowered to below the transition tem- in Table 11.2.
perature. The installed capacity was about 25 per The adaptive control takes account of the
cent of a conventional air-con system. effective acclimatization that people show after
This ‘peak lopping’ was very effective, showing periods of hot weather. Figure 11.7 shows the set-
a large drop in complaints of overheating. Table point responding to the outside air temperature.
11.1 shows a comparison between conventional The CO2 concentration demand control
air-con electricity consumption, CoolDeck only strategy is shown in Figure 11.8.
consumption, and the CoolDeck with top-up,
showing a 74 per cent saving. These are calcu-
Performance
lated values, since due to commissioning
problems, monitored data is not available. Results for two short monitoring periods, before
Important aspects of the system are that the and after, have been extrapolated to indicate the
presence of the mechanical cooling is not evi- annual performance, and are shown in Table
dent and that its control is automatic. Occupants 11.3.The new control strategy shows an average
remain under the impression that the building is reduction in annual CO2 emissions of 35 per
cooled by passive night ventilation, and are more cent.This demonstrates how low-cost changes in
tolerant of daytime temperatures. If mechanical control strategy (and almost zero embodied
cooling were more in evidence it is likely that CO2) can make significant savings.
demand for its use would become common.
Energy-efficient lighting controls
Energy efficient air-conditioning controls
High efficacy light sources and luminaires were
The offices in the 1980s block were already air installed in the second, third and sixth floors of
conditioned. A design study of the ground, first the old building, together with photo-sensitive
and atrium floors, carried out in 2004, indicated and occupancy detecting controls. Design illu-
that 42 per cent of the total energy used was fan minance is 400 lux with an installed capacity of
energy, and predicted that a saving of 22 per cent 9.7W/m2. The artificial lighting is on on/off
could be made by the installation of automatic control with a control point of 400 lux.
damper controls. Luminaires are arranged in three banks each
The new control strategy included three inside, parallel to the glazed facades of the office, al-
novative features: lowing successive switch-on from the central to
the outside bank as the daylight diminishes.The
1 pre-conditioning periods; two outer banks (each side) are controlled with
2 an adaptive cooling set-point; the photo-sensor, and the two central banks are
3 fresh air demand based on CO2 concentra- controlled by passive infra-red (PIR) occupancy
tion. detectors with a delay of 15 minutes.
Table 11.2 Control strategy for the new block air-conditioning
AHU 17 and Night Pre-conditioning 06:00 to 08:00 Day (occupied) 08:00 to 18:00
18 control (unoccupied)
options 18:00 to 06:00
Normal Morning pre-cool: Morning pre-heat: Normal operation Economy mode
summer winter (manual enable/
disable)
AHU fans Off On On On Off
Extract fans Off On On On On
Air heating Off (night setback Off Heating set-point Heating set-point Off
controlled by of 20°C of 20°C
perimeter heating)
Air cooling Off Off Off Comfort cooling Off
set-point of 24°C
adjusted based on
adaptive profile
Damper control Closed Full fresh air Full recirculation Modify to satisfy Full fresh air
fresh air and
free-cooling
requirements
Criteria – If at 06:00: space If at 06:00: space Minimum supply Space air temperature
air temperature air temperature air temperature greater than 21°C AND
greater than 21°C less than 21°C of 17°C AHU not in cooling
AND greater than AND ambient air
ambient temperature temperature is above
(plus 1°C fan 14°C AND CO2
pick-up). Ambient concentration below
air temperature 700ppm
greater than 14°C
Note: AHU = air handling unit.
Performance installed illuminance of 400 lux is high, particu-

larly for office tasks largely based on the use of
There were no data available for pre-installation VDUs. Secondly, on/off control is very wasteful,
performance; therefore measured performance is since it leads to no contribution being made by
compared with Typical and Good Practice.This daylight until 400 lux is exceeded.Thirdly, there
is shown in Table 11.4.The performance is dis- is much evidence to show that the control point
appointing, showing a 38 per cent improvement can be lower than the design artificial illumi-
on a Typical office, but a 44 per cent increase nance, in this case, say 300 lux, since the spectral
over a Good Practice office. qualities of daylight allow for a lower working
There are several factors that could explain illuminance. Finally, the high design luminance
this disappointing performance. Firstly the
116 Case Studies
Adaptive cooling profile

29
Figure 11.7 Adaptive cooling
set-point used to control
28 air-conditioning in old block
Cooling set-point (°C)
27
26
25
24
23
22 24 26 28 30 32 34
Ambient air temperature (°C)
applies to the central zone (mainly circulation), Light emitting diode (LED) lighting in
and the 15-minute detection delay may well Customer Service Centre
mean that this high level of illumination is on
most of the time. The Customer Service Centre is typical of the
Photo controls are often found to be set up new breed of ‘one stop shop’ found in City
wrongly and it is essential to check with an illu- Council offices, where residents come for a wide
minance meter that the correct switching range of Council business. Some business may
thresholds are being achieved by the control sys- be stressful, and there may be protracted waiting
tem. periods.
Note 2: Percentage fresh air for damper modulation based on CO2 concentration and free cooling
Dampers will modulate based on maximum fresh air requirement from the two schedules
Fresh air requirement based on CO2:

Damper control – CO2
CO2 (ppm) % fresh air 100
400 20
% fresh air
80
600 20 60
800 100 40
1000 100 20
0
400 500 600 700 800 900 1000
CO2 concentration (ppm)
Fresh air requirement based on free cooling

Free cooling when Space air temperature > 21°C AND Ambient air temperature < Space air temp.
When ambient < 17°C: Percentage fresh air = 100 > Space air temp. –17 / (Space air temperature – ambient air temp.)
When ambient > 17°C: 100% fresh air
Figure 11.8 CO2 concentration ventilation demand control strategy

Table 11.3 Annual CO2 savings due to improved control strategy with CO2 controlled demand and adaptive set-point
Ground floor atrium First floor atrium

Before After Before After
Monitoring dates Monitoring dates

20/06/05 to 06/07/05 23/05/06 to 15/06/06 07/07/05 to 21/07/05 09/04/08
Annual Annual Diff Annual Annual Diff
kWh CO2 (kg) kWh CO2 (kg) % kWh CO2 (kg) kWh CO2 (kg) %
50,832 21,858 35,083 15,086 31 53,293 22,916 31,006 13,333 42
Note: Results are extrapolated.
The unusual lighting installation (Figure

11.9), which changes colour under the control
of a timer, is to improve the visual quality and
interest of the waiting areas. It also provides light
at high luminous efficiency.
The energy consumption of the system was
found to be 45 per cent above the Good Practice
figure, which was disappointing. Monitored data
showed that the system had been operated for at
least three hours per day longer than necessary.
This operational issue has now been corrected and
the adjusted figure calculated now shows only a 9
per cent increase over Good Practice. It seems that
although LED lighting offers potential high effi- Figure 11.9 The LED lighting system in the Customer
ciency when used as the main white light source, Service Area is of high luminous efficacy and is programmed
decorative colour installations such as this tend to to make changes in colour to add visual interest to the
consume extra power due to the lower spectral waiting area
sensitivity of the eye to the wavelength used.
Table 11.4 Electricity consumption for lighting, third floor, 2007, compared with Typical and Good Practice
Year Area Consumption Occupation Annual Actual Typical Good

time consumption practice
m2 kwh/d days kWh kWh/m2 year

2007 398 61 252 15,372 39 54 27
118 Case Studies
Table 11.5 Energy consumption of Customer Service Centre, actual, adjusted and Good Practice
Year Area Consumption Occupation Annual Actual Typical Good

time consumption practice
m2 kW h kWh kWh/m2year
2007 198 2.1 3698 7766 39 54 27
Adjusted 198 2.1 2800 5880 29.7 54 27
Solar water heating array

Domestic water heating for the toilets and
kitchens had been provided by two 800 litre
9kW calorifiers.Water usage was approximately
1000 litres per day. Energy consumption was also
monitored and found to be about 85kWh per
day, or 0.25kWh per person. In terms of CO2
this is about 0.1kg per day per person, or a total
of 11.2 tonnes per year.
The electric calorifiers were replaced with
an array of high efficiency evacuated tube
collectors with a condensing gas boiler backup.
Two 500 litre storage vessels have twin heating
coils with the solar circuit connected to the
lower, and the gas boiler to the upper coil.This
encourages stratification leading to higher col-
lector efficiency.
The solar collectors, Figure 11.10, have an ef-
fective collector area of 18m2 and the solar circuit
is filled with 120 litres of fluid containing anti-
freeze and corrosion inhibitor.The collectors are
in three banks each with a flow rate of 4.5l/min.
A Resol type ES controller compares collector
temperature with the temperature in the calori-
fiers; the controller then switches on the
appropriate variable speed circulating pump. An
electronic display board, Figure 11.11, shows the Figure 11.10 The evacuated tube array of solar thermal
temperature of the collectors, the stored hot water collectors contributing to domestic hot water
temperature, and the accumulated thermal energy.
sumption. Hot water consumption is also

Performance shown.The high water consumption in May and
Figure 11.12 shows the actual output for the November were due to a water leak and servic-
solar hot water system together with the gas con- ing work.
Figure 11.11 The electronic display board giving a real

time readout of temperature and collected energy
Assuming the existing gas boiler is 90 per cent

efficient, the solar energy collected reduced the
gas demand by 28 per cent.
Increased space use efficiency

The energy used by a building is roughly pro-
portional to the area that is conditioned. Hence
performance and benchmarks are quoted in
kWh/m2. However it is the number of people
that is the key parameter.An unoccupied work-
station, or an empty meeting room, or wasteful
over-provision of space per person, is a waste not
only of capital resources but also of energy.
By changing furniture design and layout, and
moving to paperless archiving, the mean occu-
pancy density in Daneshill House has been
increased; that is, the space provision reduced
from 9.2m2 per person to 7.6m2 per person.This
alone would reduce the CO2 emissions per per-
son by 17 per cent.
Figure 11.12 Collected solar energy, gas and water

consumption 2007
120 Case Studies
Table 11.6 CO2 reduction by solar system from original electrical heating, and compared with all-gas system
Unit All electric Gas+ solar All gas Gas + solar
Solar input kWh 9707 9707

Gas input kWh 24,889 34,595 24,889
Elec. input kWh 25,926
CO2 emissions kg 11,148 4729 6573 4729
Annual CO2 saved kg 6419 1844
Annual CO2 reduction % Compared with elec > 58 Compared with all gas > 28
Post occupancy evaluation rooms, the worst of which recorded a dissatis-

faction vote of 69 per cent.
Figure 11.13 shows the results of the occupant It is also important to note that the highest
survey from 279 respondents.The most interest- satisfaction was recorded on the third floor of the
ing conclusion is that the refurbished floors with old block, which was where the higher density
CoolDeck returned the highest level of satisfac- layouts had been adopted.
tion, higher than refurbished air-conditioned
Overall (279) 54 26 19 % of respondents

Excellent/Good
Refurbished CoolDeck Floor 3rd floor old block (29) 76 21 3
Neutral
Refurbished CoolDeck Floor 2nd floor new block (15) 73 13 14
Bad/Very Bad
Refurbished AC Floor 3rd floor new block (15) 61 35 4
Refurbished CoolDeck Floor 6th floor (28) 61 25 14
Unfurbished
Re furbished AC Floor 4th floor new block (12) 54 31 15 floor
Refurbished AC Floor 1st floor atrium (19) 53 32 15
Refurbished AC Floor 2nd floor old block (21) 52 33 15
Un-refurbished Non AC Floor 5th floor (15) 46 31 23
Refurbished AC Floor 1st floor new block (21) 43 38 19
Refurbished AC Floor ground floor atrium (37) 38 19 43
Un-refurbished Non AC Floor 4th floor old block (13) 23 8 69
0% 20% 40% 60% 80% 100%
Source: AMA Workforce Toolket 2007/sept, AMA (472)

Ore: Q15: Overall, how do you rate your office environment?
Figure 11.13 Results of the occupant survey from 279 respondents. The most interesting conclusion is that the refurbished
floors with CoolDeck returned the highest level of satisfaction, higher than refurbished air-conditioned floors, the worst of which
recorded a dissatisfaction vote of 69 per cent.
Table 11.7 Energy and CO2 emissions for gas and electricity, before and after refurbishment
Gas CO2 kg Electricity CO2 kg Total CO2
Before refurb 397,214 75,470 1137,058 500,305 575,780

After refurb 406,015 77,142 1353,451 595,518 672,660
Overall energy performance

Both heat and electricity demand have increased,
by 22 per cent and 19 per cent respectively, and
this is disappointing. However it must be borne
in mind that the building had a serious over-
heating problem, and that the conventional
solution to this would have been air-condition-
ing, which inevitably would have led to a much
larger increase in electricity demand.
The increase in gas consumption is less sur-
prising, since the underfloor heating and the
domestic hot water, previously heated by elec-
tricity, are now heated by gas. Obviously the
savings in electricity from these heating roles
have been more than compensated by the extra
electricity for the CoolDeck and other mechan-
ical ventilation.
As with all newly commissioned buildings it
is very likely that improvements in performance
will continue to be made.
Ministry of Finance Offices,

12 Athens
Retrofit shading and mechanical system improvements to large office
building improve environment and energy performance
This large five-storey building (30,000m2) was Refurbishment strategy
originally built in the 1960s as an engineering
factory. In 1980 it was remodelled to form the The main characteristic of this refurbishment is
central office of the Ministry of Finance, hand- that it concentrates on systems and controls
ling the taxation for all of Greece. At this time rather than fabric.This means that the costs, both
issues of energy efficiency and indoor environ- in money terms and in embodied energy, are rel-
mental quality were not a priority. Recently, atively low in relation to the expected savings.
increasing dissatisfaction with the environmental The only major investment in the fabric are the
conditions, together with a growing awareness external shading devices and the replacement of
of the need for good energy performance, have the glazing on the north facade.
prompted this current work.
Figure 12.1 Main facade facing SSE

124 Case Studies
Daylighting and artificial lighting

• Use of photo-sensitive controls to maximize
the efficient use of natural light.
• Utilization of high efficiency lamps and im-
proved luminaires.
Heating
• Installation of circulating pumps of the
inverter type controlled by the BEMS ac-
cording to the internal and external
temperature, as well as the temperature dif-
Figure 12.2 Newly fitted vertical and horizontal shading ference between inlet and outlet of the
devices on WSW elevation on floors 2 and 3 with original heating water through the energy meters,
concrete brise soleil on upper floors. Material is grey painted which are installed on each boiler. In every
perforated steel to give the best combination of diffuse office a controller is installed giving the user
daylight and shading. Original internal louvre blinds shown an adjustment capability of +/–5°C over the
on the right operation of the fan coil unit.
Cooling
• Installation of a demand control cooling
Main energy saving features system per user. This system consists of a
motorized valve which is controlled by
Fabric improvements a thermostat/transmitter combined with a
valve controller. The controller is set on
• Installation of advanced shading devices to a minimum cooling temperature of 26°C.
control solar radiation gains both in winter For the cooling consumption measurement
and summer. an energy metering device is installed in the
• Replacement of single glazing with low-e area of each user. In this way they will have
double glazing on the north facade reducing the ability to control and monitor their own
heat loss in winter and heat gain in summer. consumption. The reading of the energy
meter will be transmitted to the central con-
Night-ventilation techniques troller.
• BEMS controlled night ventilation up to
8ac/h depending on indoor and outdoor air Ventilation
temperatures . • Demand-controlled ventilation using CO2
detectors to optimize and control indoor air
Ceiling fans quality.
• Selective use of fresh air whenever this is
• Installation of specially designed ceiling fans cooler than the recirculated indoor air, as well
which allow the extension of the comfort as redistribution of cooler air from nearby in-
zone up to an indoor air temperature set- door spaces with different indoor comfort
point of 28.5°C. requirements.
Ministry of Finance Offices, Athens 125
• Heat/coolth recovery on ventila-

tion, by a heat exchanger unit in
the exhaust air stream. This pro-
vides pre-heating or pre-cooling to
the incoming ventilation air, con-
tributing considerably to the
heating and cooling savings.
Energy management, control and

monitoring
• Using radio controls, no cable in-
stallation is necessary which means
that disturbance to the users is
avoided. All the sensor outputs are
Figure 12.3 The frequency of temperatures in offices
transferred to the BEMS terminal
via M-Bus protocols. The BEMS
takes into account the consumed
energy and the water volume, and controls Figure 12.3 shows the frequency of temperatures
the inverter pumps and also the activation in five of the office areas for the hottest month,
sequence of the chillers. August 2007. The performance in offices B21,
• The BEMS gathers all consumptions and B22 and B23 was good, with no temperatures
records and allocates the energy costs.With the above 30°C recorded and only 10 per cent, 12
system described above, there are two types of per cent and 6 per cent of occupied hours above
controls. One in each zone, which gives free- 28°C. Areas B26 and B28 showed considerably
dom to the user, within limits, and one in the higher temperatures with 3 per cent and 1 per
heat/coolth production system which works cent above 30°C respectively. However, it must
according to the weather conditions, and ac- be borne in mind that the ceiling fans allow the
cording to the end users’ demands. comfort zone to be extended to 28.5°C.
Table 12.1 shows the ambient temperatures
Performance recorded on the site for June–August 2007, in-
dicating an average of 32°C with a maximum of
37°C. Internal temperatures were kept consis-
Thermal comfort and air quality
tently about 10°C below this.
These had been the key issues and sources of As part of the energy efficiency measures, de-
complaint prior to the refurbishment. Several mand-control ventilation was installed to prevent
measures adopted were aimed at improving wasteful over-ventilation, and prevent a lower-
comfort, without incurring further energy con- ing of air quality by under-provision of fresh air.
sumption. These measures include external Fresh air is also available by openable windows,
shading, night ventilation, ceiling fans and the although at times of high outside temperature
demand-controlled fresh air ventilation with this will lead to local discomfort and increased
CO2 detection. cooling load.
The success of these measures is indicated by Figure 12.4 shows a graph of CO2 concen-
objective measurements of temperature and CO2 trations for August in the monitored areas and it
concentration, and subjective measurements by can be seen that concentrations above 1000ppm
user questionnaires. occur quite frequently. Specifically, CO2
126 Case Studies
Table 12.1 Ambient temperatures for the site June–August 2007
June July August

Max Avg Min Max Avg Min Max Avg Min
Daily max 43 30 22 41 32 28 37 32 26
Daily mean 32 24 18 33 27 22 31 26 22
Daily min 25 18 12 26 22 15 27 21 16
concentrations exceeded 1000ppm for 57 per Table 12.2 Measured ventilation rates in the data entry
cent of the time in June and July, 38 per cent in rooms before improvements
August. In the winter months the situation is
m3/h V(m3) l/s/pers
slightly worse with it being exceeded for 58 per
cent and 65 per cent in December and January B 21 220 548 2.50
respectively.
B 22 200 653 2.50
These high CO2 concentrations were investi-
gated in the autumn of 2007 and the ventilation B 23 425 584 4.72
rates were found to be low, as shown in Table B 26 275 564 3.10
12.2. As a result of this investigation, fresh air
ventilation rates were increased in February 2008 B 28 306 550 3.40
as indicated.
CO2 concentration in data entry rooms for August 2007

1800
1600
1400
CO2 concentration (ppm)
1200
1000
800
600
400
200
0
data entry room B21 data entry room B22 data entry room B23 data entry room B26 data entry room B28
Figure 12.4 Monitored CO2 concentrations for August 2007

Daylighting and artificial lighting luminous environment for the occupant. In

terms of the former the energy consumption for
The original glazing ran in a continuous strip lighting had been monitored before the refurb-
between cill level at 1.2m to the ceiling at 2.4m. ishment took place and found to be 46kWh/
Modelling studies using the software Radiance m2yr. Consumption dropped to 38.6kWh/m2yr,
and Daylight had shown that average daylight a reduction of 16 per cent.
factors (DF) exceeded 2 per cent in almost all This is a disappointing reduction and could
cases, including rooms shaded by the large con- be accounted for by the increased efficiency of
crete brise soleil on the fourth and fifth floors. the lamps alone. It could be due to over-
The addition of the shading devices on the illumination, although quoted illuminance meas-
SSE, SSW and WNW, in order to control solar urements suggest that these are between 200 and
gains, inevitably reduces the available daylight. 300 lux. However, these values were measured
However, due to the geometry of the devices, using the downward facing control sensors and it
they tend to shade direct sun, more than light is not clear if the values were corrected for illu-
from the diffuse sky.They also can reflect diffuse minance on the workplane. This could also
light back into the room. In this way, they reduce explain the disappointing performance of the
the non-uniformity of illumination, without re- control system.
ducing the average daylight illuminance below a
level requiring artificial light.
A systematic study was carried out using ra- The photovoltaic array
diance to find the best combination of The photovoltaic array was originally going to
reflectances, ranging from 80 per cent (nominally be part of the shading system.Technical consid-
white) to 20 per cent.A value of 50 per cent re- erations changed this to a roof-mounted array.
flectance (light grey) was chosen as the best The panels, total area 25.8m2, are mounted at 30°
compromise between illuminance, uniformity inclination facing south, on the roof terrace of
and reduction of glare. the building.Their operation has been recorded
The artificial light is provided by high effi- since the beginning of January 2008 for two
ciency Osram Lumilux T5 sources with high months. The array had generated 447kWh of
frequency dimmable ballast giving 104 lu- electricity.
mens/W (compared with 75 lumens/W for Only 7 per cent and 10 per cent of the annual
conventional fluorescents). The lighting is con- solar radiation is available in January and Febru-
trolled through the BEMS that receives signals ary. Assuming a constant efficiency, a predicted
from internal sensors in the rooms. Sensors were annual yield would be 2629kWh.
placed in two rows at 2.4m and 6m from the
window wall (the room was 9m deep) and each Overall energy performance
sensor controlled the four surrounding lumin-
aires. Table 12.3 shows that for the year 2000, the pri-
mary1 energy consumption had been
Daylighting performance 53.6kWh/m2 for heating and 87.9kWh/m2 for
cooling. For the year 2007, after renovation, the
The performance of a daylighting design must measured energy for heating was 34.3kWh/m2,
be judged by both its ability to displace artificial and for cooling, 47.0kWh/m2.
lighting energy, and to provide an acceptable The winter of 2007 was mild, and for com-
1 Primary energy is the energy value of the source fuel. For electricity the delivered energy is multiplied by 3.3.
128 Case Studies
parison the heating figure must be corrected to gains. Further contributions must be made by
the same number of degree hours. This gives the improved demand-controlled ventilation
38.2kWh/m2 for the corrected heating energy, with variable speed fans. Reduction in lighting
showing a reduction of 29 per cent.The cooling use due to the photo-sensitive controls should
energy is reduced by 46 per cent. also reduce internal gains, but the relatively small
reduction in lighting energy, suggests that that
Table 12.3 Primary energy consumption for heating, component is a relatively small one.
lighting and electricity
2000 2007–08 % reduction Comfort surveys
Annual cooling The subjective outcome of the conditions shown

energy kWh/m2 87.9 47.0 46 under Thermal comfort and air quality is indicated
in Figure 12.5 in the bottom two rows.This in-
Annual heating cludes the responses of all office areas. Individual
energy kWh/m2 53.6 38.2 29 areas showed slight difference, with the offices
Annual lighting on the NNW orientation showing 60 per cent
energy kWh/m2 46.0 38.6 16 satisfaction with temperature, but the ENE ori-
entation achieving only 33 per cent. It is
Annual electricity
interesting to note that the areas returning poor
kWh/m2 (office
performance are those which are not usually as-
equipment) 26 26
sociated with problems of solar gain. This
suggests that the problem lies with the combin-
ation of high internal gains and poor control or
Heating inadequate capacity.This issue is already receiv-
Two observations can be made about the heating ing attention.
energy. Firstly, the actual value is still high – Satisfaction with ventilation shows a similar
38kWh/m2 for a climate with only 4000 degree pattern with only 40 per cent being satisfied
hours for base temperature 18°C (i.e. 167 degree overall and dropping to 23 per cent in the ENE
days), and for a building with high internal gains. office.
Secondly the reduction of 29 per cent is modest, In interpreting these results it must be borne
bearing in mind the investment in low-e glaz- in mind that high levels of satisfaction are rarely
ing, and demand-controlled ventilation. reported.Typically people report neutrality when
The annual heating energy quoted above in- there is no adverse condition prevailing.There is
cludes electrical power for fans and pumps.The also a probable link between the undisputed high
probable explanation for the result is that since CO2 concentrations and the perception of ther-
the actual heating load is small, the total energy mal discomfort – that is, if CO2 concentration
is dominated by the electrical part, which has not and humidity are kept low, the higher tempera-
changed very much. It is also an indicator of just tures may be more acceptable. Furthermore, the
how much parasitic energy can be used in air comfort survey was conducted in October 2007
conditioning systems. before the increased ventilation rates had been
implemented and before the ceiling fans had
been installed.
Cooling
The cooling energy has shown a significant de-
crease of 46 per cent.This must be due in part to
the effect of the shading devices reducing solar
Comfort conditions – representative offices of GSIS building
overall comfort
interior quality
view
privacy
noise
artificial lighting
daylight
ventilation
temperature
0 10 20 30 40 50 60 70
(–2) not satisfactory (–1) (0) satisfactory (+1) (+2) very satisfactory
Figure 12.5 Comfort survey

The Meyer Hospital, Florence

13
Refurbishment and addition of large greenhouse to historic building in
warm climate
The building dates from the 1930s when it was
a hospital for tuberculosis patients. It consists of
a long three-storey terrace running east–west, of
traditional construction with very thick walls and
a tiled roof. A central corridor serves rooms on
the north and south side (Figures 13.1 and 13.2).
The total area is 10,480m2. The building had
been semi-derelict for some years.A new paedi-
atric hospital has been built on the site adjacent
and the refurbished building forms the adminis-
trative and reception centre.
Refurbishment strategy
Being of traditional construction the building
was non-insulated and single glazed. The first
Figure 13.1 South elevation of the Villa Ognissanti, the
consideration was how to insulate the envelope.
original Meyer Hospital
The roof presented no problem, since during re-
construction insulation material was included, in
this case mineral fibre quilt.The windows were
also replaced giving the opportunity to incorpo- The solid walls presented some problems. Exter-
rate low-e double glazing in timber frames, nal insulation would have disturbed traditional
giving a U-value of 2.85W/°Cm2.This also re- detailing of this historic building, whilst internal
duced uncontrolled infiltration. insulation would have reduced thermal inertia.
Figure 13.2 Plan of the east–west running terrace showing the additional greenhouse (centre)
132 Case Studies
Figure 13.3 Replacement timber windows with low-e

glazing Figure 13.4 Refurbished traditional louvre shutters on
south elevation
In the end, bearing in mind the nature of the cli- energy conserving measure, this strategy may be
mate (mild Mediterranean) it was decided to a little surprising for a warm climate. However,
leave the walls non-insulated other than a small there were two mitigating circumstances – firstly
improvement brought by new external render much of the lower glazing is shaded by vegeta-
containing a natural lightweight volcanic aggre- tion, and being in contact with the massive
gate. The resultant U-value is calculated to be non-insulated wall provides stabilizing thermal
2.0W/°Cm2. mass. However, considerable interest has been
A new building energy management system
(BEMS) was also installed. This not only man-
aged the conventional heating and cooling, but
also the night cooling.
Originally, the renewed south-facing win-
dows were to have included an interpane shading
system, magnetically controlled from outside the
sealed unit. These were finally rejected on the
grounds that since the external louvred casement
shutters (Figure 13.4) had to be kept for historic
reasons, the expense of the additional integral
shading was not justified.
The greenhouse
The boldest intervention is the installation of a
large greenhouse on the south side of the central
pavilion abutting the lower two of the three Figure 13.5 Section of greenhouse showing shading and
storeys (Figures 13.5, 13.6 and 13.7). As an ventilation openings
The Meyer Hospital, Florence 133
focused on the risk of overheating in the green-

house itself, and in the adjacent offices.
The structure is made from laminated timber
columns and is a striking addition to the archi-
tecture. Its spatial function is as the arrivals foyer
and reception area for the whole hospital com-
plex.
Figure 13.6 Interior view of greenhouse showing semi-

transparent PV shading
Position Daylight Factor %

1 1.71
2 1.37
3 2.57
4 2.02
Average 1.91
Figure 13.8 Simulated daylight results for office facing

greenhouse
Figure 13.7 Exterior view of greenhouse during

is provided by semi-transparent photovoltaic
construction
panels. This, and the ventilation provision, are
shown in Figure 13.5.The ventilation openings
Recognizing the potential risk of overheating, at the top and bottom of the greenhouse are
the design demonstrates the sound principle of controlled by the BEMS.A further open area can
shading and ventilation. In this case, the shading be obtained by leaving the main doors open.
134 Case Studies
Table 13.1 CO2 emissions for corrected measured Meyer 2007 data compared with reference case
kWh kWh/m2 CO2 factor CO2
Gas reference 1,257,600 120 0.19 238,944

Meyer 876,652 83.7 0.19 166,563
Electricity reference 1,194,720 114 0.44 525,676
Meyer 880,320 84 0.44 387,340
Note: Total CO2 kg – Reference 764,620; Meyer 553,903.
Daylighting
The impact of the greenhouse on the daylight-
ing of the adjacent office rooms had been tested
by simulation (Figure 13.8). The result shows a
mean value of 1.91 per cent.
Occupants report a high level of satisfaction
with the lighting, 4.0 on a 1–5 scale in the end
pavilions, but slightly less, 3.5 in the central pavil-
ion adjacent to the greenhouse (Figure 13.9).
Overall energy performance

The Meyer project is one of those where there
has been major change in the function of the
building, so there is no comparable data available
for energy consumption before the refurbish-
ment. Thus a reference office has been defined.
This shows a 28 per cent reduction in emis-
sions, although it has to be said that the reference
values for gas and electricity per m2 are very high
Figure 13.9 Results of user survey for office facing
for a building in the climate of Florence.
greenhouse (central pavilion) and office facing open air
(lateral pavilion). Scale ranges from 0 – very dissatisfied to
Comfort 5 – very satisfied.
Questionnaires were issued to occupants in the
central wing adjacent to the greenhouse, and in tive side of neutral, which is typical where dis-
the two lateral wings. The results are shown in comfort is not present, and should therefore be
Figure 13.10.These are consistent, with the ex- regarded as successful, although since all values
ception of a slightly lower satisfaction for lighting are averaged, it is not possible to see if discomfort
reported in the central wing, which could be due was reported by some respondents.
to the presence of the greenhouse. Unfortunately It is interesting to note that a positive response
the question does not distinguish between arti- is recorded for the level of user control.This in-
ficial lighting and daylighting. dicates that the temperature controllers in each
Comfort, which is probably strongly weighted room, providing a simple user-friendly adaptive
towards thermal comfort, is a little on the posi- opportunity, are appreciated.
Appendices
A
Appendices 137
138 The Handbook of Sustainable Refurbishment

Appendices 139

Appendices 141
Appendices 143

Appendices 145

Appendices 147


Appendices 151

Appendices 153
Appendices 155

Appendices 157

Appendices 159

Appendices 161

Appendices 163
Index
I
I
A see also double skins
attic spaces 39–40, 44
absorption chillers 77
I
absorptive glass 49, 50–1
acoustics 68–9, 100 B
actuators 81 BEMS see building energy management
adaptive controls 84–6, 114, 116–17 systems
adaptive opportunities 7–8 biomass heating 89–90
adjustable shading systems 58–9 blinds 58, 59–60, 86
advanced natural ventilation 9 boilers 71, 76
air-conditioning 7–9, 72–3 break-even point, rebuild 4
case studies 111, 114–16, 120–1 BREEAM (Building Research Establishment
deep-plan buildings 5 Environmental Assessment Method) 22
energy performance 15–17 bridging, cold bridges 28, 32–4, 42, 45, 102
hybrid/mixed mode systems 86–7 budget constraints 13
air heating systems 72–3 building energy management systems (BEMS)
air quality 66, 97–8, 100, 105, 125–6 83–4, 95–6, 99, 104–6, 124–5, 132–3
air requirements 116 Building Regulations, UK 21–2
air temperatures 74–5, 125–6 Building Research Establishment
The Albatros, Den Helder 6, 54, 93–100 Environmental Assessment Method
aluminium coatings 60 (BREEAM) 22
aluminium frames 53, 94–5 buildings as sub-systems 4–5
angles of incidence 52 bulk materials 3
aperture modifications, windows 55–6 see also concrete
I
architectural integration 18–19
artificial lighting 11, 77–80 C
The Albatros 98 carbon dioxide see CO2 emissions
Athens Ministry of Finance 124, 127 Carbon Reduction Commitment (CRC) 22
daylight detection 83 caretaker controls 86
Lycée Chevrollier 103–5, 108–9 cavities (roofs) 39–40, 44
occupancy detection 81–2 cavity walls 35–7
see also lighting ceiling fans 124
Athens Ministry of Finance 123–9 cellular offices 83
atria 63–70, 102, 105–6
166 index
central control systems 80–1 Daneshill House 114–17

change of use 5–7, 93 Lycée Chevrollier 104, 107
chillers 77, 87, 113–14 Meyer Hospital 134
CHP see combined heat and power systems convection energy transfer 48, 50
climatic factors convector heaters 73–4
atria 65 CoolDeck system 112–14, 120
natural ventilation 18 see also cold bridges
CO2 emissions 3–23 cooling systems 76–7
The Albatros 94–5, 97–8 Athens Ministry of Finance 124, 127–8
Athens Ministry of Finance 125–6, 128 Daneshill House 112–14, 116, 120
Daneshill House 114, 116–17, 119–21 evaporative 45–6
fans/pumps 76 hybrid/mixed mode systems 86–7
heat distribution systems 72 underfloor 27–8
Lycée Chevrollier 104–5, 107–10 see also air-conditioning; natural ventilation
Meyer Hospital 134 coolth emitters 76
office buildings 5 COPs (Coefficients of Performance) 77
refrigeration 77 cost effectiveness
coated glass 49–50 mechanical services 71
Coefficients of Performance (COPs) 77 renewable energy 89
cold bridges 28, 32–4, 42, 45, 102 see also economic factors
combined heat and power (CHP) systems 71, County Hall, London 11
77 CRC (Carbon Reduction Commitment) 22
comfort curtain walling 51
The Albatros 100
I
Athens Ministry of Finance 125–6, 128–9
D
heat emitters 74–6
hybrid/mixed mode systems 87 dampers, cooling systems 116
Lycée Chevrollier 102, 108–9 Daneshill House, Stevenage 87, 111–21
Meyer Hospital 134 daylight detection systems 82–3
standards 7–9 daylight factors (DFs) 82–4, 98–9, 103
commissioned buildings 110 daylight redistribution 56–7, 59
see also newbuild daylighting 10–13, 56–7, 59, 77, 82–4
composite walls 35, 36–7 The Albatros 98–9, 100
concrete 3, 9, 111–13 Athens Ministry of Finance 124, 127
condensation 34–5, 36–7, 40–1, 43, 76 atria 67–8
condensing boilers 71, 76 Daneshill House 111
conduction energy transfer 48, 50 glazing materials 47, 49–50, 55–6
consumption see energy performance; gas high performance daylighting 60–1
consumption Lycée Chevrollier 101–4, 108–9
control systems 71–87 Meyer Hospital 133–4
The Albatros 98–9 daytime temperatures, atria 65–6
Athens Ministry of Finance 123–9 DECs (Display Energy Certificates) 22
Index 167
deep-plan buildings 5, 11–12 low emission refurbishment 3

demand controls 79–81, 124–5 LT Europe software 15–17
dewpoint profiles 34, 36–7, 41 Lycée Chevrollier 107–8
DFs see daylight factors Meyer Hospital 134
digital controls 81 quantifying 14–18
dimming controls, lighting 82, 85, 98–9 Energy Performance Certificates (EPCs) 21
direct expansion (DX) units 113–14 Energy Performance of Buildings Directive
Display Energy Certificates (DECs) 22 (EPBD) 20–2
double glazing 48–9, 55 energy supply, eco-interaction 20
double skins 58, 63–70, 93–8 energy transfer, glazing 47–50
ductwork 72 engineering integration 19
DX (direct expansion units) 113–14 environmental benefits 3–4, 13–14
environmental comfort standards 7–9
I
see also comfort
E
environmental conditioning 79–80
earth constructions 31 environmental regulations 20–3
eco-communities 19–20 environmental strategies see strategies
economic factors 3–4 EPBD (Energy Performance of Buildings
see also cost effectiveness Directive) 20–2
EEAS (Energy Efficiency Accreditation EPCs (Energy Performance Certificates) 21
Scheme) 22–3 European Union (EU) directives 20–2
electric heaters 75 evaporative cooling 45–6
electrical energy external insulation, walls 31–3
The Albatros 99–100 external shading systems 57, 58–9
CO2 emissions 76, 77
I
Daneshill House 117, 120–1
Lycée Chevrollier 102, 107 F
embodied CO2 3, 94–5, 109 fan coils 74, 76
emissions see CO2 emissions fans 72–4, 76–7, 99, 112, 124
energy conservation 20, 63–7, 68, 83 feedback controls 85–6, 87
Energy Efficiency Accreditation Scheme filters, air-conditioning 73
(EEAS) 22–3 ‘fin effect’ 53
energy performance fin shading systems 58
The Albatros 98–9 fixed shading systems 58–9
Athens Ministry of Finance 124–8 flat roofs 40–1
atria 63–7 floors 27–9, 102–4
building/services/occupants system 4–5 flow resistance, heat distribution 72–3
change of use 6–7 framing systems
Daneshill House 112–19, 121 double skins 94–5
daylight detection 83 wall insulation 31, 33
double skins 68 windows 51–5
eco-interaction 20 free cooling systems 116
168 Index
I
G I
I
gas consumption 107, 118–21 illuminance levels/distribution 79, 82–3, 85
glazing 47–51, 53–6, 60 indoor air quality see air quality
The Albatros 93–5 infiltration rates 9
Athens Ministry of Finance 123–4 infrared (IR) light 44, 50
atria 67–8 inner leaf, cavity walls 37
double skins 63, 69 insulation
lighting systems 11–12, 16–17 cavity walls 35–7
over-glazed buildings 7–8 floors 27, 28–9
see also windows Lycée Chevrollier 101–3, 107
global lighting efficacy 78 Meyer Hospital 131–2
green roofs 45–6 roofs 39–46
greenhouse, Meyer Hospital 131, 132–4 solid floors 27
ground floors 27–9 solid walls 31–4
ground sourced refrigeration 77 suspended floors 28–9
thermal response 29
I
walls 31–4, 35–7
H
integrated newbuild/refurbishment 18–19
heat distribution 72–3 integrated shading systems 57–8
heat emitters 73–6 intelligent skins 63, 68
heat exchangers 71 intermediate floors 29
heat gains internal insulation, walls 33
glazing 50–1 internal shading systems 57, 59–60
natural ventilation 9–10 internally reflected components (IRCs) 103
heat loads interpane shading systems 57–8
atria 65–6 interstitial condensation 34–5, 36–7, 40–1, 43
lighting 16 IR (infrared) light 44, 50
heat transfer/transmission 36, 47–50 IRCs (internally reflected components) 103
heating systems 71–6
I
The Albatros 94, 96–100
Athens Ministry of Finance 124, 127–8 K
Daneshill House 111, 118–21 Kalamazoo building, Birmingham 12
local control 80
IL
Lycée Chevrollier 105, 107
renewable energy 89–90
underfloor 27–8, 74, 111 lamps 78–9
high performance daylighting 60–1 LEDs (light emitting diodes) 116–17
high performance glazing 50–1, 53–4 legislation 20–3
historic buildings 54–5, 131–2 life-cycle performance 94
horizontal louvres 59 light emitting diodes (LEDs) 116–17
hospital buildings 131–4 light obstructions 52–3
hybrid systems 8, 9, 86–7 lighting
Index 169
The Albatros 93–4, 98–9, 100

Athens Ministry of Finance 124, 127–8
I
O
controls 81–5, 104, 114–17 occupancy demand matching 79–81, 124–5

Daneshill House 111, 114–17 occupancy density
energy performance 16–17 The Albatros 97–8
installations 77–80 Daneshill House 119–20
Lycée Chevrollier 101–5, 107–9 occupancy detection lighting controls 81–2,
Meyer Hospital 134 104, 114
see also daylight... occupant controls 84–6
lightshelves 56–8 occupants as sub-systems 4–5
lightweight building comfort standards 7 office buildings
lightweight walls 35, 36–7 case studies 93–100, 111–21, 123–9
load-bearing insulation 27 change of use 6, 93
local control systems 79–80, 81 CO2 emissions 5, 72
louvred shading systems 56–8, 59, 103, 132 comfort standards 7
low emission refurbishment 3–23, 44, 49–50 lighting 79, 83
low-emissivity coatings 49–50 opaque surface acoustics 69
low-emissivity membranes 44 open plan buildings 83, 86
LT Europe software 14–17 opportunities, adaptive 7–8
luminaires 78–9, 81–2, 84, 103–4, 114 optical transmittance 47
see also lighting outer leaf, cavity walls 37
luminous efficacy 50–1, 60, 77–8 over-glazed buildings 7–8
Lycée Chevrollier,Angers 9, 18, 101–10 overhang shading systems 58, 60
overheating performance
I
Daneshill House 111, 121
M LT Europe software 15–17
masonry walls 35, 36–7 Lycée Chevrollier 101–2
mechanical services/controls 71–87, 114, Meyer Hospital 133
123–9 walls 31
Meyer Hospital, Florence 5, 56, 131–4 windows 50–1
I
Ministry of Finance Offices,Athens 123–9
mixed mode systems 8, 9, 86–7 P
I
PAC (partially air-conditioned) buildings 9
N paints, roofs 44
natural ventilation 8, 9–11, 15, 17, 18, 59 partially air-conditioned (PAC) buildings 9
newbuild 3–4, 18–19 passive systems 8–12, 86–7
see also commissioned buildings PCM (phase change materials) 112–14
night ventilation 9–10, 17, 104, 112–13, 124 perforated screens 58
performance see energy performance;
overheating performance; thermal
performance
permanent supplementary artificial lighting
170 Index
(PSALi) 11 retractable shading systems 58–9

personal benefits 13–14 REVIVAL buildings 5–6, 9, 56, 59, 86
phase change materials (PCM) 112–14 rigid insulation 31, 33
photo-sensitive detectors 82, 86, 104, 114, 116 roller blinds 59–60
photovoltaic (PV) applications 89–90, 102, 106, roof ponds 45, 46
127, 133 rooflighting 10, 56
pipework, heat distribution 72 roofs 39–46, 131
pitched roofs 39, 40–1, 43
I
planning policies, UK 22
S
plants
atria 68, 69 SBS (sick building syndrome) 11–12
green roofs 45–6 school buildings 63, 101–10
shading systems 132 screed finish, floors 27
polyurethane insulation 43 second skins see double skins
positioning heat emitters 75 secondary glazing 53–4
pre-cast concrete 9 separating walls, atria 65–6, 68
principles 1–23 service CO2 94–5
prioritizing options 13–18 service systems 4–5, 71–87, 114, 123–9
protectivity, atria 64–5, 70 shading factors 51
PSALi (permanent supplementary artificial shading systems
lighting) 11 adaptive control 86
pumps 76–7 The Albatros 98
PV see photovoltaic applications Athens Ministry of Finance 123–4, 127
atria 67–8
I
Lycée Chevrollier 102, 103
Q Meyer Hospital 132–3
quantification of energy benefits 14–18 windows 51, 56–60
SHF (Solar Heat Fraction) 43
I
sick building syndrome (SBS) 11–12
R
side-lit rooms
radiation transmission 49–50 daylight factors 83–4
radiators 73–5 shading systems 56–7
raised floors 27 sizing heat emitters 75–6
rammed earth constructions 31 socio-economic factors 3–4
RE (renewable energy) 89–90, 93 solar gains
rebuild vs refurbishment 3–4 roofs 39, 43–4
recycling provisions 106 solid walls 32
reflectance, roofs 43–4 windows 50–1, 56–7
reflective glass 49, 50 Solar Heat Gain Factors 43
refrigeration 77 solar panels 89
regulations 20–3 see also photovoltaic applications
renewable energy (RE) 89–90, 93 solar water heating 118–20
Index 171
solarity, atria 65, 69–70 cooling systems 112

solid ground floors 27–8 roofs 44–6
solid roofs 39, 41–3 solid walls 32–3
solid walls 31–5, 131–2 thermal performance
sound insulation 69 The Albatros 95–6, 100
space use efficiency 119 Athens Ministry of Finance 125–6
spatial mix systems 87 atria 64–7
standards, comfort 7–9 double skins 68
steel 3 floor insulation 29
Stevenage ‘new town’ 111 glazing materials 47–50
strategies Lycée Chevrollier 101–2, 104–6, 108–9
The Albatros 93–4 roofs 43–5
Athens Ministry of Finance 123 wall insulation 32–3, 37
Daneshill House 111 window frames 53–5
low emission refurbishment 3–23 thermal transmittance 47–50
Lycée Chevrollier 101–2 see also heat transfer/transmission
Meyer Hospital 131–4 thermostatic controls 86, 107
stratification of temperature 66–7 timber frames
structural deck, solid roofs 42–3 walls 31
summer performance windows 54–5
The Albatros 96, 100 time-programming controls 80
Athens Ministry of Finance 125–6 tinted glass 49, 50–1
atria 67 toilet use 99–100
Lycée Chevrollier 105–6, 108–9 transparent buildings 12
support systems, windows 51–5
I
surface reflectance 43–4
U
surface resistance/conductance 48
suspended ground floors 28–9 U-values 47–50
systems concept 4–5 UF (utilization factor) 78
UK legislation 21–2
I
ultraviolet (UV) light 50
T underfloor cooling 27–8
task lighting 79 underfloor heating 27–8, 74–6, 111
temperature profiles ‘upside-down’ roofs 41–2
Athens Ministry of Finance 125–6 UPVC-framed windows 54
atria 64, 65–7 urban reflectance 44
cavity walls 36–7 urban renewal 19–20
Daneshill House 113–14 utilization factor (UF) 78
double skins 96–7 UV (ultraviolet) light 50
heat emitters 74–6
Lycée Chevrollier 104–5
thermal mass
172 Index
I
V I
W
vapour checks Wallesey School 63
roofs 41 walls 31–7, 131–2
walls 34–5, 36–7 waste management 106
vapour permeability, roofs 40, 41, 43 water heating systems 72, 118–21
vegetation water pumps 76–7
atria 68, 69 water surface, roof ponds 46
green roofs 45–6 water temperatures 75–6
shading systems 132 water vapour see vapour...
ventilation 8–11, 15, 17–18, 59 watering systems, plants 68
The Albatros 93–100 waterproof membranes 41–2
Athens Ministry of Finance 124–6 Wauquez Department Store 10
atria 65–7, 69 weathering function, roofs 39
cavity walls 35–6 wet cooling towers 77
Daneshill House 112–13 wind direction, ventilation 98
fans 76 wind turbines 89
local control 80 windows 10–12, 47–61, 104–5, 131–2
Lycée Chevrollier 102, 104–6, 108–9 winter performance
Meyer Hospital 132–3 The Albatros 95–6, 100
roofs 40, 41 Athens Ministry of Finance 126
see also air-conditioning atria 65–7
visible spectrum 49–50 Lycée Chevrollier105 108–9
voids, roofs with 39, 40–1 wireless digital controls 81
voluntary schemes 22–3 wood see timber frames
I
Z
zoning systems 72, 80–1, 83, 85

RIBA - The Handbook of Sustainable Refurbishment PDF

Uploaded by

Copyright:

Available Formats

RIBA - The Handbook of Sustainable Refurbishment PDF

Uploaded by

Document Information

Original Title

Copyright

Available Formats

Share this document

Share or Embed Document

Sharing Options

Did you find this document useful?

Is this content inappropriate?

Copyright:

Available Formats

RIBA - The Handbook of Sustainable Refurbishment PDF

Uploaded by

Copyright:

Available Formats

What are some of the challenges of refurbishing existing buildings?

What are some of the challenges of refurbishing existing buildings?

What are some benefits of refurbishing existing buildings over demolishing and rebuilding?

What are some benefits of refurbishing existing buildings over demolishing and rebuilding?

PPC live area 246x189mm, Spine 17mm, bleed 18mm

The Handbook of Sustainable Refurbishment

Earthscan strives to minimize its impact on the environment Nick V. Baker

The Handbook of Sustainable Refurbishment

Earthscan works with RIBA Publishing, part of the Royal Institute

First published by Earthscan in the UK and USA in 2009

Copyright © Nick V. Baker, 2009

All rights reserved

Typeset by FiSH Books, London

For a full list of publications please contact:

22883 Quicksilver Drive, Sterling,VA 20166-2012, USA

Library of Congress Cataloging-in-Publication Data

Part One Principles

Part Two Practice

vi The Handbook of Sustainable Refurbishment

2.3 Intermediate floors ......................................................................................29

The Handbook of Sustainable Refurbishment vii

Thermal performance of framing............................................................53

6 Atria and Double Skins ......................................................................63

7 Mechanical Services and Controls ........................................................71

viii The Handbook of Sustainable Refurbishment

Daylight detection ..................................................................................82

8 Renewable Energy Options .................................................................89

Part Three Case Studies

10 Lycée Chevrollier, Angers, France ......................................................101

The Handbook of Sustainable Refurbishment ix

Waste management and other environmental issues ..........................................106

11 Daneshill House, Stevenage, UK .........................................................111

12 Ministry of Finance Offices, Athens ....................................................123

x The Handbook of Sustainable Refurbishment

13 The Meyer Hospital, Florence ............................................................131

List of Acronyms and Abbreviations

AC air-conditioned EPC Energy Performance Certificate

Part One Principles

Strategy for Low

These reasons may be sufficient in themselves to waste

justify the cost. If at the same time the building deliveries

can be made more energy efficient, there will be site energy

Figure 1.2 CO2 emissions for

Figure 1.3 The building, the mechanical

Strategy for Low Emission Refurbishment 5

However, there may be individual cases where

Figure 1.6 REVIVAL building Meyer Hospital, Florence:

These changes may bring about benefits and dis-

It is difficult to generalize here, but it could be

Strategy for Low Emission Refurbishment 7

58 per cent of that of the measured average for

refurb. building, new use.

original building, new use.

newbuild, new use.

average for building stock

Strategy for Low Emission Refurbishment 9

Figure 1.10 Overall occupant comfort by

Natural ventilation Refurbishment measures to reduce uncontrolled

Figure 1.12 The principle of night