AGIL - MODULAR UPS

Including Smart ByPass (SBP)

User Manual V7.2
RE-INVENTING THE MODULAR UPS
THE NEW GENERATION OF POWER CONVERTERS

SELECTIVITY
Adapted response to short circuit and overload

VERSATILE CHARGING
Short or long backup recovery time at no extra cost

BATTERY SUSTAINABILITY
Qualitative charging for longer battery life expectancy

HARSHEST AC INPUT CONDITIONS

Without compromising the quality of the AC output

Copyright © 2013. Construction electroniques & telecommunications S.A.

All rights reserved. The contents in document are subject to change without notice.
The products presented are protected by several international patents and trademarks.
Address: CE+T S.a, Rue du Charbonnage 12, B 4020 Wandre, Belgium
www.cet-power.com - [email protected] www.cet-power.com
Table of content
1. Introduction............................................................................................................................................................... 4
1.1 Scope of the manual.......................................................................................................................................... 4
1.2 User Interface presentation................................................................................................................................ 4
1.2.1 AGIL UPS module User Interface ........................................................................................................... 4
1.2.2 T4S supervisor...................................................................................................................................... 8
1.2.3 CATENA GUI Interface............................................................................................................................ 9
2. Installation ................................................................................................................................................................ 11
3. T4S/CATENA start-up ................................................................................................................................................ 14
3.1 Applying start-up power.................................................................................................................................... 14
4. Standard Features..................................................................................................................................................... 15
4.1 AC Input Sub-menu........................................................................................................................................... 17
4.2 DC Battery Sub-menu........................................................................................................................................ 17
4.3 AGIL Modules Sub-menu.................................................................................................................................. 18
4.3.1 AGIL Modules Sub-menu....................................................................................................................... 18
4.4 AC Output Load Sub-menu................................................................................................................................ 19
4.5 SBP Modules Sub-menu.................................................................................................................................... 20
4.5.1 SBP Modules Sub-menu........................................................................................................................ 20
5. Toolbar...................................................................................................................................................................... 22
5.1 Events and Log.................................................................................................................................................. 22
5.2 Input, output mapping .. ..................................................................................................................................... 23
5.3 Files.................................................................................................................................................................. 24
5.4 Parameters........................................................................................................................................................ 25
5.4.1 Monitoring............................................................................................................................................. 25
5.4.2 Digital Input and output relay mapping.................................................................................................. 28
5.4.3 Power, parameter setting....................................................................................................................... 29
5.4.4 Battery 1 and Battery 2.......................................................................................................................... 33
5.4.5 Info........................................................................................................................................................ 36
6. Factory Ranges and Defaults..................................................................................................................................... 37
6.1 Definition........................................................................................................................................................... 38
7. SNMP V1 & SNMP V3 Configuration........................................................................................................................... 40
7.1 SNMPv1 configuration....................................................................................................................................... 40
7.2 SNMPv1 MIB (RFC1628).................................................................................................................................... 40
7.3 SNMPv3 configuration....................................................................................................................................... 40
ANNEXE 1 Battery Management with AGIL Technology and T4S V2................................................................................. 43
ANNEXE 2 AGIL Manual By-Pass (MBP) installation manual.............................................................................................. 47
ANNEXE 3 SNMP Alarms.................................................................................................................................................. 50
ANNEXE 4 FAQ............................................................................................................................................................... 59

2 – Agil Modular UPS – User manual – v7.2

Release Note:
Release date Modified page
Version Modifications
(DD/MM/YYYY) number
7.0 06/01/2014 - First release of the Manual.
7 and 9 Modified picture
13 Added Note
7.1 28/05/2014 14 Password details updated
27 to 30 Text updated
34 Table updated
7.2 05/06/2015 SBP Information

3 – Agil Modular UPS – User manual – v7.2

1. Introduction
1.1 Scope of the manual
This document describes the software features, on-site setup and operation of the AGIL Modular Power system. Please refer to
AGIL Installation manual for hardware installation and wiring information.

1.2 User Interface presentation

1.2.1 AGIL UPS module User Interface

Output power bar graph 0-100% (25% increment)

Phase 1, phase 2, phase 3

Module ON/OFF switch

AC Input/ AC output module status

DC input/ Communication module status

4 – Agil Modular UPS – User manual – v7.2

1.2.1.1 Output Power LED interface :

Each segment represent 25% load.

0-25 / 25,1-50 / 50,1-75 / 75,1-100

Load can differ between the 3 phases in one module

Load can differ in one phase in several modules

Overload (blinking)
100% - 110% segment 0-25 blinking
110,1% - 135% segment 0-50 blinking

5 – Agil Modular UPS – User manual – v7.2

1.2.1.2 Module status LEDs interface
AC input LEDs interface

Starting up (all LEDs) OFF

AC Input OK (within limits) GREEN
AC Input not OK (out of limits) ORANGE
(Auto restart) Flash ORANGE
(Manual restart) Flash RED
(Non recoverable) RED
AC failure OFF + external alarm

AC output LEDs interface

Starting up ( ) GREEN Blink

AC Output OK (within limits) GREEN
AC Output not OK (out of limits) ORANGE
(auto restart) ORANGE Blink
(manual restart) RED Blink
(non recover) RED
Remote OFF (man restart) OR/GR/OR/GR
sequence every x seconds

6 – Agil Modular UPS – User manual – v7.2

 Starting up ( ) OFF
DC OK (within limits) GREEN
DC not OK (out of limits) YELLOW
(auto restart) YELLOW Blink
(man restart) RED Blink
(non recover) RED
No battery
connected ( ) OFF

Communication LEDs interface

COM OK ( ) GREEN
COM ERROR (Bus A or B) GREEN Blink still one bus present
COM ERROR (Bus A & B) RED Blink
Module and system will continue working with one BUS failing with two bus failing
the module/system will isolate and shut down.

7 – Agil Modular UPS – User manual – v7.2

1.2.2 T4S supervisor
1 2 3

T4S supervisor monitors the AGIL module as well as system environment. It is connected to :
„„ The AGIL module through the CE+T bus [1].
„„ The Catena (if present ) through the “Catena bus” [2].
„„ To a computer via ETHERNET port (RJ45) [3].
T4S has:
„„ 8 “digital input “ referred to has D1 to D8.
„„ 8 output relays Major Alarm, Minor Alarm, R3 to R8.
„„ 3 temperature probes T1 to T3.
„„ Dual DC input 12V power supply (not included) [4].

Please note the T4S and CATENA are not master and therefore can be removed during operation with
affecting the operation of the UPS AC output.

8 – Agil Modular UPS – User manual – v7.2

1.2.3 CATENA GUI Interface
CATENA GUI interface allows the user to easily access the system monitoring via a powerful web based graphic display.
In addition to the touch-screen display the user can also access to the same GUI using an Ethernet port present on the T4S or
CATENA.

Catena “Panel Mounting Version”

Please note that if CATENA is installed, the ETHERNET port of the T4S is not available, Ethernet access will have to go through
CATENA.

9 – Agil Modular UPS – User manual – v7.2

CATENA comes in two versions:
„„ Rack mounted where the unit takes 3RU inside the cabinet flush mounted.
„„ Door or Panel mounted where the unit is fixed to the door or panel.

Catena “Rack Mounting Version”

Power supply and connectivity are provided on the back of the unit :

10 – Agil Modular UPS – User manual – v7.2

2. Installation
T4S is a DIN rail mountable controller which is connected to the AGIL module / system as indicated in the schematic in next page

11 – Agil Modular UPS – User manual – v7.2

12 – Agil Modular UPS – User manual – v7.2
Software Overview
The software embedded in T4S and CATENA allows complete system supervision through “touchscreen display” or via web
browser, and provides functionalities such as :
„„ System setting and configuration (password protected).
„„ System status and information display.
„„ System alarms and events log file.
„„ System self-maintenance (battery test, battery boost charge,….).

Note : Last software T4S & CATENA V2 will give full compatibility with AGIL module software version 11 and
higher. Lower version of AGIL Module above V8 will operate but might present some limitation. AGIL module
with SW version V8 cannot operate with T4S and must be upgraded prior to the connection with T4S.

13 – Agil Modular UPS – User manual – v7.2

3. T4S/CATENA start-up
If you have installed the T4S and /or CATENA by yourself, make sure to respect the connections as indicated in the schematic.
If you have ordered the complete solution with cabinet and module from CE+T Power, both controllers are installed, wired, tested
and preconfigured according the system.

3.1 Applying start-up power

NOTE: The controller will perform a short self-test as it boots up. Alarm alerts are normal.
„„ Initiate the start-up routine by applying power to the T4S (close protection breaker powering the controller).
„„ Use the touchscreen or a laptop to connect to the system.
NB: if you are connecting with your laptop, default IP address of user interface is 192.168.0.2.
There are two access levels:
•  Basic: after version 3.1, basic access does not require password. Before that, default password is pass123.
•  Expert: default password is pass456 but it’s strongly advised to users to change that password.

In case of lost password, please refer to FAQ

„„ Check and adjust alarms and control levels in the controller sub-menus.
„„ Check and adjust battery settings in the battery sub-menus; e.g. float, equalize voltage, etc.
„„ If on touchscreen, check the communications settings for remote access as needed.

NOTE: System modification and setting may result in alarm event. Make sure you are applying modification
carefully.

14 – Agil Modular UPS – User manual – v7.2

4. Standard Features

The main screen presents an overview of the system where any “click” on the magnifying glass icon will result to access the
selected sub-menu:
[1] AC input sub-menu.
[2] DC battery sub-menu.
[3] AGIL modules sub-menu.
[4] AC output load sub-menu.

A click on an icon in the toolbar will give you, respectively, access to the event, communication, parameter, files sub-menu
The main screen shows the status of each of your power system’s components.
„„ AC input : Green, Red.
„„ Battery : Green, Orange, Red.
„„ AGIL module(s) : 3 LEDs (AC input , DC input, AC output).
„„ AC output / Load : Green , Red.
The energy flow direction is indicated by the “moving” white point on the power lines.

15 – Agil Modular UPS – User manual – v7.2

If you have SBP in your system, then Home page will look like this:

[5]

SBP modules in the system are showed on top of ups ones. The magnifying glass icon in SBP section gives access to SBP
sub-menu [5].

16 – Agil Modular UPS – User manual – v7.2

4.1 AC Input Sub-menu
Provides AC input information (up to 3
phases ).
-AC input voltage.
-AC input current.
-AC input Frequency.
-AC input Power (kW).

4.2 DC Battery Sub-menu

Battery x (x = 1 or 2) provide info on
batteries status.
-BOOST On or OFF
-Battery Test ON or OFF
-Estimated autonomy and info on last test,
boost charge, discharge

17 – Agil Modular UPS – User manual – v7.2

4.3 AGIL Modules Sub-menu
Provides AGIL module info
-Number of module installed
Redundancy level
-Installed power.
-Available power.
-Temperature of the warmest module.

4.3.1 AGIL Modules Sub-menu.

Clicking on the “Select Module” icon will open a module selection table.
Each number represents the address of a module in the system.
„„ A green number indicates an installed and running module.
„„ An orange number indicates an installed but in recoverable error module.
„„ A red number indicates an installed but in non-recoverable error module.
„„ A grey number indicates a module manually turned OFF. Only available in “Expert” mode.
„„ A white number indicates an empty slot.
Table of module installed / not installed.
Click on an installed module to access
the specific information of the selected
module.

18 – Agil Modular UPS – User manual – v7.2

 Selected Module information
-Click “identify” to see the
corresponding module in the bay (all LEDs
blinking).
-Module status indicated through the LED
color on :
-AC input.
-DC input.
-AC output.
Green : OK.
Organe : Recoverable error.
Red : Non recoverable error.

When a module is removed of the system, it must be uninstalled by clicking that icon.

When fan is replaced in the module, the alarm “fan replaced” should be cleared by clicking this icon.

Module can be switched off by software by clicking this icon. The current state (on or off) of the module is
also given by that icon.

Module AC group can be changed by clicking this icon in the AC title. The same can be done for DC group
on DC title.

To identify the current module in the system, click this icon to make it blink.

4.4 AC Output Load Sub-menu

AC output control board.
-Different measures (V, I, F, P, S).
-Individual phase status L1 to L3.
-Level of power bargraph.

19 – Agil Modular UPS – User manual – v7.2

4.5 SBP Modules Sub-menu
NB: This sub-menu is accessible only when there is at least one SBP installed in the system.
Provides SBP module info
- Number of module installed.
- Redundancy level.
- Installed power.
- Available power.
- T° average of the module.

4.5.1 SBP Modules Sub-menu.

Clicking on the “Select Module” icon will open a module selection table.

20 – Agil Modular UPS – User manual – v7.2

Clicking on any line will give the view of the selected module

When a module is removed of the system, it must be uninstalled by clicking that icon.

When fan is replaced in the module, the alarm “fan replaced” should be cleared by clicking this icon.

Module can be switched off by software by clicking this icon. The current state (on or off) of the module is
also given by that icon.

Module AC group can be changed by clicking this icon in the AC title.

To identify the current module in the system, click this icon to make it blink.

21 – Agil Modular UPS – User manual – v7.2

5. Toolbar

5.1 Events and Log

Please note “text alarm page” is refreshed every minute for easy reading while LED’s are active immediately.

Display the active event/alarm present on

the system.
- Red: Major alarm.
- Orange: Minor alarm.
- White : No alarm.
Click on “Log” to view the history log file
presented below

Log file can be filtered using the filter

menu.

22 – Agil Modular UPS – User manual – v7.2

 Do not forget to click apply to activated the
selected filter.

Clear Filter will remove all selected filter

and view all log file.

5.2 Input, output mapping

Present the digital input 1 to 8 mapping

Present the output relay mapping with

possibility to test each relay with the
“toogle” button. Click and check relay
chaging status with an ohmeter.
Note:
Only available in expert mode through
laptop web browser.

23 – Agil Modular UPS – User manual – v7.2

5.3 Files
Transfer screen allow to export the log file and export or import configuration file

Transfer:
Event History
−−Both Event log and configuration file can
be exported.
−−Event file name cet.log is a text format
*.txt file.
−−Log size limited to about 500 – 800
lines.
−−Click on “clear” will erase the CET log
file. Password protected.

Configuration:
−−Configuration file can be exported or
imported from to the T4S.

Update :

To upgrade T4S firmware. Import the file

from computer and download to T4S.

Language :

T4S store maximum 3 languages that can

be changed, updated or cleared.

24 – Agil Modular UPS – User manual – v7.2

5.4 Parameters
WARNING !
All values present are default values ! User shall consult and change default value with caution. Wrong
parameters can affect the system operation, reliability, battery life duration, system autonomy

5.4.1 Monitoring
NOTE: Once the new parameter has been entered click « save » to record the data otherwise the previous
value will be kept.
Time: Allow setting of Date and Time+

The menu allow to :

-Set time and region
-Change password
-Set T4S network parameter
-Set Catena network parameter
-Set T° sensor
-Define the alarm mapping

25 – Agil Modular UPS – User manual – v7.2

Regional Settings

-Choose language.
-Site name.
-Site Localisation.
-Auto logout delay (will disconnect user
after xx minutes if no action).

Password => choose password. Read the

information carefully at section 3.1, page
14.

Network => to enter the parameter for

remote site connection through Ethernet
port.

26 – Agil Modular UPS – User manual – v7.2

 Scrolling down let you configure all
network & Snmp related settings. See
section 7, page 40 for more details and
how to

Temperature sensors =>allow to configure the T° probe for battery compensation or ambient T°.

27 – Agil Modular UPS – User manual – v7.2

5.4.2 Digital Input and output relay mapping
Inputs : Digital Input mapping =>mapping and assign a “name” to any of the 8 digital input. By default DG1 and DG2 are related to
Manual By Pass if present and surge arrestor if present.

Input labels :
-Allow to define a label that will be used
for any digital input activated.
-Example
-Label 1 : Door open will report the event
“Door open” every time the digital input 1
is active.
By default Dig Inp 1 is affect to “Manual
By Pass” and Dig In2 to “Surge protection
SPD”

Relay labels define the text that will be

used for output relay
Relay 1 and 2 are reserved for Major and
Minor alarm. Relay 3 to 8 are free for any
alarm definition

Relays delay allow to define to delay in sec

after which the relay will change status
once the event has occurred.
Range from 2 seconds to 60 seconds.

28 – Agil Modular UPS – User manual – v7.2

 Relay mapping

Allow to perform the mapping of any alarm

to any relay association.
One alarm can be allocated to more then
one relays

5.4.3 Power, parameter setting

The menu “Power” allow to perform the setting of the system, AC input, DC battery, AC output and Others.
General =>to configure
- the number of modules.
- module redundancy.
- DC group (if more then one battery group is mandatory) max 2 independent battery can be configured.

General
To affect number of module
redundant.
To define number of DC group.
One DC group per battery maximum
2 DC group.

29 – Agil Modular UPS – User manual – v7.2

AC IN : to define the alarm level for Low and High AC input voltage, Frequency, Synchronisation & Phase mapping sequence.

AC in A
To configure AC input Parameter.
Phase shift (120° for 3 phase)
Sync Priority: Define on which
Phase - if all present – the module
will synchronise the AC output.
Low and High xxx voltage to
configure the voltage boundaries
min and max from where AGIL will
transfer to DC and vice versa

DC GROUP : to define min, max battery voltage for .Default value are related to 408VDC nominal battery (204 cells).

NOTE if more then 1 battery, there will be 2 DC group for Battery 1 and Battery 2.

DC Group 1
To configure DC input 1 Parameter.
Low and High xxx voltage to
configure boundaries min and
max from where AGIL will STOP
to preserve battery from deep
discharge.

Neutral connected:1 means the AC

output is 3x400VAC + Neutral
while 0 means the AC output is
3x400VAC without neutral. The load
is 3phase without neutral.

30 – Agil Modular UPS – User manual – v7.2

BATTERY type and capacity. To enter the data for charging voltage adjustment and T° compensation coefficient and T°
compensation range where the compensation apply.

DC Group 2
To configure DC input 2 Parameter.
Low and High xxx voltage to
configure boundaries min and
max from where AGIL will STOP
to preserve battery from deep
discharge.

Neutral connected:1 means the AC

output is 3x400VAC + Neutral
while 0 means the AC output is
3x400VAC without neutral. The load
is 3phase without neutral.

AC OUT to adjust AC output voltage, AC out frequency range and phase sequence.

AC out
To configure AC output parameter
AC out Phase sequence and AC out
phase shift

Nominal AC out frequency. If set

different then AC input the BOOST
will not be available
Frequency limit 30 to 70Hz

Note : The phase sequence must be respected between AC in and AC out. Improper phase sequence might
damages equipment during MBP procedure.

31 – Agil Modular UPS – User manual – v7.2

Other
Other
Customer repartition: 0 to 100% to define
the ratio from AC in and battery. 0 =
100% from AC input
Commutation time: define the duration to
return from DC to AC
Synchro speed:
To define to speed for synchronization -2
slow to +2 fast
AC reinjection allowed
1: allowed 0: blocked
Vout min ovrl too long:
To define the value before alarm OVL
appear
Delay ovrl too long:
To define the timeout to generate OVL
alarm
Triac enabled: to disable the BOOST of
the module set value to 0. Set to 1 by
default

32 – Agil Modular UPS – User manual – v7.2

5.4.4 Battery 1 and Battery 2
Warning: !!!
Battery configuration is extremely important. There must be correct value entered for battery. Those
parameter will define:
- The floating charging voltage;
- The boost charging voltage (if enabled);
- The current limitation to protect battery from overcharging current;
- The prediction of the battery capacity when battery test are performed.
Wrong value will affect the operation of the system and might have an impact on the battery lifetime.

Battery 1
Configure battery. Refer to battery
manufacturer for detail value
Nbr of Cells: AGIL need always odd
number as there is middle point.
Ideal 204 cells min 180 max 204
Cell float V at 20°C
Max current to limit during charging
. Never exceed C10/4
Cells capacity. If more then one
string please multiply the cell
capacity x nbr of string.

33 – Agil Modular UPS – User manual – v7.2

 Battery 1
Compensation
Enter the value from manufacturer
mV/°C

Min : from wher e the compensation

start

Max : from where compensation

stop

Battery 1 Test
To set up the battery 1 test
parameter Power, time duration and
voltage stop

Auto test to define the periodicity of

the test

34 – Agil Modular UPS – User manual – v7.2

 BOOST
To set up Boost, first enable it then
set up the parameter
- Voltage per cell (from
manufacturer)
Boost can be activated on voltage
value : Voltage start. After discharge
below xxV per cell the boost will be
activated or if
- Boost can be activate on
charging current value
- Boost can be activate
periodically
BOOST stop always if the duration
exceed the Stop duration value

Battery 1 Alarms
Cell Low voltage : End of autonomy
alarm. AGIL will shut down very
shortly by LVD
Low Pre alarm : Pre-notification of
low battery voltage
Autonomy pre-alarm : Set the % of
capacity available after the alarm
Remaining capacity alarm % of
autonomy available

35 – Agil Modular UPS – User manual – v7.2

5.4.5 Info

Info T4S

Provide info about T4S serial

number, software version bootloader
version

36 – Agil Modular UPS – User manual – v7.2

6. Factory Ranges and Defaults
Submenu Item Programmable range Default values 408Vdc
Float (FL) Voltage 408 – 490 463 Vdc
Equalize (BOOST) Voltage 408 – 490 480 Vdc (2,35V/per cell)
Test Batterie (BT) Voltage 315 – 490 391 Vdc
Battery current limit 0-1000 =C10/5 (Battery capacity/5)
Battery in discharge 315 – 490 430 Vdc
Battery Low 1 alarm 315 – 490 360 Vdc
Battery Low high 315 – 490 340 Vdc
System Saturation alarm 0 – 100 80%
Equalize Timeout 0 - 48 24 hours
Test Batterie Duration 0-8 8.0 hours

Submenu Item Programmable range Default values

Adress IP CATENA 192.168.0.3
Subnet Mask N/A 255.255.255.0
Adress IP T4S N/A 192.168.0.2

37 – Agil Modular UPS – User manual – v7.2

6.1 Definition
AC Alternating current
DI Digital Input
ALCO Alarm cutoff
BCT Battery current termination
BDT Battery discharge test
BOD Battery on discharge
BT Test Batterie (mode)
CAN Controller Area Network
DC Direct current
DOD Depth of discharge
EQ Equalize (mode or voltage)
FL Float (mode or voltage)
GUI Graphical utilisateur interface
IP Internet Protocol
LCD Liquid crystal display
LED Light emitting diode
LVA Low voltage alarm
LVC Low voltage connect
LVD Low voltage disconnect
MAC Media Access Control; p.e. MAC address
MIB Management Information Base
OVP Over-voltage protection
PPP Point to Point Protocol
RAS Remote access server
SCI Serial Communication Interface
SNMP Simple Network Management Protocol
TCP/IP Transmission Control Protocol / Internet Protocol
Trap Event notification

38 – Agil Modular UPS – User manual – v7.2

Alarms
- Type: No Alarm (0) Minor(1) Major(2)

;710; ;257.NO TRANSMISSION ; ;2;

;711; ;258.MBP ENGAGED ; ;1;
;712; ;259.SURGE ARRESTER ; ;1;
;713; ;260.REDUNDANCY LOST ; ;1;
;714; ;261.REDUND + 1 LOST ; ;2;
;715; ;262.SYS SATURATED ; ;1;
;716; ;263.MAIN SOURCE LOST ; ;1;
;717; ;264.SEC SOURCE LOST ; ;1;
;718; ;265.BUS FAIL ; ;2;
;719;
;266.FAILURE ; ;2;
;720;
;267.STARTED ; ;1;
;721; ;268.LOG CLEARED ; ;1;
;722; ;269.CONFIG MODIFIED ; ;1;
;723; ;270.NEW MOD DETECTED ; ;1;
;724; ;271.DATE & TIME MOD ; ;1;
;725; ;272.CFG READ IN MOD ; ;1;
;726; ;273.LOG NEARLY FULL ; ;1;
;727; ;274.FLASH ERROR ; ;2;
;728; ;275.USER STACK HIGH ; ;1;
;729; ;276.IRQ STACK HIGH ; ;1;
;730; ;277.MODULE(S) ABSENT ; ;1;
;731; ;327.AUX POWER FAILURE ; ;1;
;732; ;329.OUT OF SERVICE ; ;2;

39 – Agil Modular UPS – User manual – v7.2

7. SNMP V1 & SNMP V3 Configuration
SNMP is now available on T4S supervisor and on Catena display.
SNMPv1 is available on T4S supervisor. The MIB implemented on T4S SNMP agent is the standard USP MIB defined by RFC1628.
Catena display now includes a SNMPv1 to SNMPv3 proxy.
The main difference between SNMPv1 and SNMPv3 is the addition of secured connection in SNMPv3.

7.1 SNMPv1 configuration

For SNMPv1 agent configuration, go to Parameters > Monitoring > Network.

See T4S network section for ETH port configuration:

„„ IP address.
„„ Subnet mask.
„„ Gateway.

See T4S SNMP section for SNMP agent configuration:

„„ Trap receivers IP addresses. Up to 5 trap receivers can be configured.
„„ Note that ports 161 and 162 (for traps) are used. Not configurable.

7.2 SNMPv1 MIB (RFC1628)

The MIB is the standard UPS MIB defined by RFC1628.
Meaning of “input lines”: input lines are AC input groups as existing in T4S web interface. One tri-phase system will have 3 input
lines, one for each phase.
Meaning of “output lines”: output lines are AC output groups as existing in T4S web interface.

The following features of UPS MIB are not implemented in T4S:

„„ Writable entries. The current MIB is read-only. Entries can only be edited through the web server. For this reason, the
upsConfig section is also read-only.
„„ Bypass values. As T4S doesn’t include the monitoring of bypass devices, bypass measurements are not available
in the MIB. It is however possible to know when the system switched to MBP by reading ups Output Source value
(OID .1.3.6.1.2.1.33.1.4.1).
„„ Well known test. Only standard battery test is available. No other test is implemented in T4S at current state.
Any feature defined in RFC1628 that is not in the previous list is available.

7.3 SNMPv3 configuration

For SNMPv3, you need a Catena display. The Catena display can be used as SNMPv1 to SNMPv3 proxy.
The configuration of Catena display is managed by T4S supervisor.
In T4S web interface, go to Parameters > Monitoring > Network.

40 – Agil Modular UPS – User manual – v7.2

See Catena network section:
Set IP address, subnet mask, and gateway for local network.
Set “bridge enable” option. By default, both ETH ports of Catena are in the same LAN. If the bridge is disabled, then each port is on
an independent LAN.
If bridge is disabled, set IP address, subnet mask, and gateway for external network.
If bridge is disabled, the most outward ETH port is connected to the local network, and the most inward ETH port is connected to
the external network. The T4S must be on the local network.
Please not that SNMPv1 agent and T4S web server are have no security. For a secure connection, it is strongly recommended to
use SNMPv3 interface only (T4S on local network and bridge disabled).

See Catena SNMP section:

SNMPv3 context can be configured.

SNMPv1 agent community can be configured. Not used for now since T4S agent community is not configurable (public by default).

Three users can be configured:

„„ Read-only user. There is no authentication and no encryption. No other parameter than user name is required.
„„ NoPriv user. This user is authenticated but there is no encryption. Authentication protocol (MD5 or SHA) must be selected.
Authentication password must be configured.
„„ Priv user. This user is authenticated and connection is encrypted. Authentication protocol (MD5 or SHA) must be selected.
Authentication password must be configured. Encryption protocol (DES or AES) must be selected. Encryption key must be
configured.
„„ A user can be completely disabled by setting an empty user name.

Base OID’s have to be configured for each user.

One trap received can be configured:

„„ Trap received IP address.
„„ Engine ID.
„„ Security level. You can select if the trap will use both authentication and encryption, only authentication, or none.
„„ Trap authentication password. Only required if authentication is enabled in security level option.
„„ Trap authentication protocol (MD5 or SHA). Only required if authentication is enabled in security level option.
„„ Trap encryption key. Only required if encryption is enabled in security level option.
„„ Trap encryption protocol (DES or AES). Only required if encryption is enabled in security level option.

41 – Agil Modular UPS – User manual – v7.2

ANNEXE
Battery Management with AGIL technology and T4S V2
Content:

ANNEXE 1 BATTERY MANAGEMENT WITH AGIL TECHNOLOGY

1. INTRODUCTION 43
2. CE+T BATTERY CHARGING AND DISCHARGING MODE 43
2.1 MODE 1 BOOST 43
2.2 MODE 2 FLOAT 44
2.3 MODE 3 Discharge 45
2.4 MODE 4 BATTERY TEST 45

ANNEXE 2 AGIL Manual By-Pass (MBP) installation manual

1. INTRODUCTION 47
2. Presentation 48
3. MBP Wiring 49

ANNEXE 3 SNMP Alarm

1. SNMP Alarm 50

ANNEXE 4 FAQ
1. FAQ 59

42 – Agil Modular UPS – User manual – v7.2

ANNEXE 1 Battery Management with AGIL Technology and T4S V2

1. Introduction
Battery is critical element in a UPS. Many manufacturer offer high performances of their electronic but sometimes forgot about
providing an efficient and reliable battery management.
Battery are fragile and need to be treated accordingly in discharge and recharge conditions. The purpose of this document is to
provide an overview of how TSI and AGIL manage the batteries, prevent their end of life and reduce possible occurrence of thermal
runaway.

2. CE+T Battery charging and discharging MODE

The purpose of a charger is to “refill” the charge tank of the battery. There are many other features which enhance the
convenience of the charger, or grant protection for the battery being charged. These built-in protection features is what
fundamentally elongates the battery’s life, or more correctly, prevents premature failure
TSI technology provide those features :
„„ higher current levels reduce recharge times (assuming the battery can accept charge at high rates).
„„ voltage limits, current limits, and time out to reduce excessive gassing at end-of charge, and prevent dry-out.
„„ modified voltage and current limits as a function of temperature reduce gassing and electrode damage.
„„ BOOST or Equalize mode to equalize battery blocs periodically
CE+T AGIL and controller T4S battery operating mode are described below

2.1 MODE 1 BOOST

This mode need to be activated and configured according the battery data from the manufacturer
A CCCV (constant current, constant voltage ) algorithm to provide a “quick an fast recharge. Ideally to recover 80% of the battery
capacity in maximum 8 hours. This mode use a Uset voltage level associated to current limit protection
Figure 1. Typical recharge curve versus time for voltage and current.

43 – Agil Modular UPS – User manual – v7.2

MODE 1 algorithm can be trigger based on the following parameter :
„„ Trig Start Voltage : Will activate MODE 1 when battery voltage goes below preset level
„„ Trig Start Current : will activate MODE 1 when battery current goes above the preset value
„„ Trig Start Period : Will activate MODE 1 periodically base on preset value.
„„ Manual Start : Will activate MODE 1 manually through the GUI menu
In mode 1 the temperature compensation is disabled.
MODE 1 algorithm can be stopped based on the following parameter :
„„ Trig Stop Current :Will stop MODE 1 when battery voltage goes below preset level and MODE 1 for minimum 5 minutes (to
avoid successive Start and Stop)
„„ Trig Stop Duration : 1H to 48H will stop MODE 1 (always active) will stop the MODE1 after the duration.

Note : If MODE1 stop based on “duration” before the “Stop current” reached an alarm will be generated as
the battery need to be checked.
„„ Trig Start Period : Will activate MODE 1 periodically base on preset value.
„„ An alarm appear in the system: MODE 1 will be disabled in case of alarm presence
„„ Manual stop : will STOP MODE 1 manually through the GUI menu

2.2 MODE 2 FLOAT :

This is the normal operating mode for maintaining the battery in charge. This mode is enabled by default

The MODE 2, charging voltage is adapted (provided it is enabled in the configuration) according the temperature. Using the
charging curve below
T° bas-low and T° haut-high are adjustable

Note : If the temperature probe is disconnected or defective the voltage will come back to the value at 20°C.
An alarm T° sensor fail” will be generated

44 – Agil Modular UPS – User manual – v7.2

2.3 MODE 3 Discharge
Discharge mode is active when energy flow is taken from the battery to the DC/AC converter (inverter) of each module
In this mode the T4S monitoring sent a voltage and current value to the AGIL module. This help in case of one module has AC input
failure to take power from DC and is feed through the other module to avoid discharging the battery and assure the continuity of
supply for the AC load
Following alarms and time out available :
„„ Ubat<Ufloat
„„ BAT cell V low
„„ BAT end of autonomy
„„ BAT discharge time out (Battery in discharge for more than xx minutes)
„„ V BAT stop : AGIL will stop operating to prevent deep discharge

Note : During discharge, T4S will record battery discharge value

2.4 MODE 4 BATTERY TEST

Battery test is a helpful function to get reliable information on the battery conditions and capacity.
It is recommended to perform periodic test of the battery but more important to perform those test in the same conditions in order
to obtain comparative data over the years of the battery lifetime
Starting BATTERY TEST conditions:
„„ Manual
„„ Trig Start Period : Specify the day of the week to perform the periodic test and the number of weeks between 2 tests.

Note : Periodic test will start only if no discharge during last 96 hrs to guarantee the same start conditions
for every test.
Stopping BATTERY TEST conditions :
„„ Trig Stop Duration : always active. Define the maximum time duration of a test
„„ Trig Stop Voltage : stop the test when battery voltage reaches the preset value
„„ An alarm appears in the system:
„„ AC IN failure
„„ M
odule failure
„„ V BAT too low
„„ System Overlaod
„„ Manually through the GUI menu

Note: During any test or battery discharge the following data will be recorded.

45 – Agil Modular UPS – User manual – v7.2

START BAT x TEST + data and time
FIN BAT x TEST + data and time
For every delta of 1VDC record of:
-  Date in seconds
-  Battery voltage
-  Battery current
-  Bat Temperature
END BAT TEST + date+Time, VBAT, Temp+ Success, FAIL
START BAT x DISH + data and time
FIN BAT x DISH + data and time
For every delta of 1VDC record of:
-  Date in seconds
-  Battery voltage
-  Battery current
-  Bat Temperature
END BAT DISH + date+Time, VBAT, TEmp

46 – Agil Modular UPS – User manual – v7.2

ANNEXE 2 AGIL Manual By-Pass (MBP) installation manual
The purpose of this document is to provide guidelines for customers to implement, assemble, wire and test external manual by-
passes using CE+T AGIL modular UPS’ with T4S monitoring units.
The CE+T delivered cabinets equipped with manual by pass are not concerned by this document.

1. Introduction
The purpose of the manual by-pass also named “service by pass” is to provide the capability to completely by- pass the modular
UPS AGIL system in order :
„„ To perform service maintenance to the equipment
„„ To externally by-pass the UPS installation and allow the removal of the equipment

Principle of operation
The manual by-pass (MBP) is a “make before break” by-pass manual switch.
The MBP can be in 3 position mode :
OFF or NORMAL : the MBP is not engaged (OFF) and the USP normally feeds the critical load.
INTERIM or TRANSFER : the MBP is in a temporary interim position where the AC load is supplied through the manual by-
pass. The AGIL UPS is in start up mode and not yet connected to the AC output.
ON or BY PASS : the MBP is engaged, the AC input feeds the AC load, the UPS modules are OFF.
Block wiring of the MBP

47 – Agil Modular UPS – User manual – v7.2

NORMAL mode or OFF : S1 is open, S2 and S3 are closed
INTERIM or TRANSFER : S1 is closed
S2 and S3 can be in position OPEN or CLOSED depending where you are in the manual by pass
procedure

Note : This positon is only temporary.

It is used to allow the modules to start up and synchronize with the AC input.
The user should not keep the by-pass in the INTERIM position.
BY-PASS mode or ON : S1 is closed. S2 and S3 are open.

2. Presentation
The Manual By-pass can be provided with 2 executions :

1. Rotary Switch for AGIL 60 kVA and AGIL 160 kVA

2. Two (2 )power switches external to the AGIL cabinet for power above 160 kVA

Please refer to the AGIL installation manual for more specific procedures.

48 – Agil Modular UPS – User manual – v7.2

3. MBP Wiring
Both solutions (rotary by-pass or separate switches) need to have auxiliary contacts that need to be wired to the monitoring unit
as described below and as shown on the drawing present in annexe

Aux 3 (from the by pass switch) : Provides an input to the controller indicating that the MBP is engaged

Aux 1 (From AC input switch) and Aux 2 (from the by pass SWITCH) :
„„ Switch OFF the AGIL modules once the MBP is engaged.
„„ Allow the AGIL modules to switch ON when the MBP placed in the INTERIM position.

49 – Agil Modular UPS – User manual – v7.2

ANNEXE 3 SNMP Alarms
SNMP alarm
#ID AGIL alarm + alarm name
Bad battery
421 battery:”Fault”
On batteries
417 battery:”Discharge”
Battery low
434 battery: “Not defined”

Battery depleted
49 dc: source+ too low transfered,
50 dc: source+ too low transfered,
53 dc: source+ too low stop,
54 dc: source- too low stop,
57 dc: source+ no voltage,
58 dc: source- no voltage,
424 battery: “Voltage end of autonomy”

Bad temperature (any)

34 dc: Temperature derating,
35 dc: Temperature too high,
36 dc: Temperature sensor fail,
66 acin: Temperature derating,
67 acin: Temperature too high,
68 acin: Temperature sensor fail,
98 out: Temperature derating,
99 out: Temperature too high,
100 out: Temperature sensor fail,
430 battery: Temp sensor fail,
431 battery: Over temperature,
Bad input (Ac in out of tolerance)
81 acin: Source V too low transfert,
82 acin: Source V too high transfert,

50 – Agil Modular UPS – User manual – v7.2

 84 acin: Source V too low stop,
85 acin: Source V too high stop,
86 acin: Source freque too low,
87 acin: Source freque too high,
88 acin: Source V no voltage,
Bad output (out out of tolerance, for other reason than overload)
111 out: IGBT driver alarm,
112 out: not defined 112 (introduced by error but no consequence)
113 out: Driver not ready,
114 out: Driver fault,
116 out: IGBT error,
117 out: Vout pi2 error,
118 out: Vout mpi2 error,
120 out: Backfeed error,
121 out: Too many start
Overload
103 out: Overload,
104 out: power derating,
105 out: Vout too low,
106 out: overload too long,
115 out: Over-current,
132 monitoring: System saturated,
On bypass
129 out: MBP engaged,
bypass bad
(NA)
manual output off
16 module: Off (remote off),
17 module: Off (front switch),
119 out: Off (bus)
manual ups off (? “whole ups)
(NA)
charger fail
418 battery: Charging fail

51 – Agil Modular UPS – User manual – v7.2

any output off state
131 monitoring: redundancy lost
151 monitoring: Module off detected
ups off state
(NA)
fan failure
6 module: fan failure,
fuse failure
122 out: Out fuse open
general ups fault
152 monitoring: Module KO detected
diagnostic test failed
(NA)
com lost (agent - ups)
(NA)
shutdown pending
133 monitoring: Main source lost
+134 monitoring: Secondary source lost
shutdown imminent (5 sec)
133 monitoring: Main source lost
+134 monitoring: Secondary source lost
alarm test in progress
420: battery: test active
AGIL alarms identifiers:
------------------------

Dans la structure CI_AlarmEntry, tu prends l’alarmId, tu soustrais 95, et tu obtiens l’identifiant

de ce document.

Template:
alarmText[identifiant]=alarmNameText;

52 – Agil Modular UPS – User manual – v7.2

//module
alarmText[1]=”Start”;
alarmText[2]=”Boost not available”;
alarmText[3]=”Boost cooling-down”;
alarmText[4]=”Boost failure”;
alarmText[5]=”Fan replace”;
alarmText[6]=”Fan failure”;
alarmText[7]=”Power perturbed”;
alarmText[8]=”Param phase query”;
alarmText[9]=”Param mismatch”;
alarmText[10]=”No source”;
alarmText[11]=”Vcap too high”;
alarmText[12]=”Vcap too low”;
alarmText[13]=”Vref error”;
alarmText[14]=”Memory eeprom error”;
alarmText[15]=”Memory flash error”;
alarmText[16]=”Off (remote off)”;
alarmText[17]=”Off (front switch)”;
alarmText[18]=”Bus noise”;
alarmText[19]=”Bus A fail”;
alarmText[20]=”Bus B fail”;
alarmText[21]=”Bus sync filter error”;
alarmText[22]=”Not defined 22”;
alarmText[23]=”Not defined 23”;
alarmText[24]=”Bus A not present”;
alarmText[25]=”Bus B not present”;
alarmText[26]=”Bus frame collision”;
alarmText[27]=”Not defined 27”;
alarmText[28]=”Not defined 28”;
alarmText[29]=”Not defined 29”;
alarmText[30]=”Not defined 30”;
alarmText[31]=”Not defined 31”;
alarmText[32]=”Not defined 32”;

53 – Agil Modular UPS – User manual – v7.2

//DC
alarmText[33]=”Start”;
alarmText[34]=”Temperature derating”;
alarmText[35]=”Temperature too high”;
alarmText[36]=”Temperature sensor fail”;
alarmText[37]=”Auto-calib error”;
alarmText[38]=”Pdc too low”;
alarmText[39]=”Impedance too high”;
alarmText[40]=”No AC”;
alarmText[41]=”Current trip”;
alarmText[42]=”Driver error”;
alarmText[43]=”Not defined 43”;
alarmText[44]=”Not defined 44”;
alarmText[45]=”Not defined 45”;
alarmText[46]=”Not defined 46”;
alarmText[47]=”Not defined 47”;
alarmText[48]=”Not defined 48”;
alarmText[49]=”Source+ too low - transfered”;
alarmText[50]=”Source- too low - transfered”;
alarmText[51]=”Source+ too high - transfered”;
alarmText[52]=”Source- too high - transfered”;
alarmText[53]=”Source+ too low - stop”;
alarmText[54]=”Source- too low - stop”;
alarmText[55]=”Source+ too high - stop”;
alarmText[56]=”Source- too high - stop”;
alarmText[57]=”Not defined 57”;
alarmText[58]=”Not defined 58”;
alarmText[59]=”Not defined 59”;
alarmText[60]=”Not defined 60”;
alarmText[61]=”Not defined 61”;
alarmText[62]=”Not defined 62”;
alarmText[63]=”Not defined 63”;
alarmText[64]=”Not defined 64”;

54 – Agil Modular UPS – User manual – v7.2

//AC
alarmText[65]=”Start”;
alarmText[66]=”Temperature derating”;
alarmText[67]=”Temperature too high”;
alarmText[68]=”Temperature sensor fail”;
alarmText[69]=”Auto-calib error”;
alarmText[70]=”Impedance Too High”;
alarmText[71]=”Backfeed error”;
alarmText[72]=”Not defined 72”;
alarmText[73]=”Overcurrent”;
alarmText[74]=”Driver not ready”;
alarmText[75]=”Driver fault”;
alarmText[76]=”Driver perturbed”;
alarmText[77]=”Not defined 77”;
alarmText[78]=”Not defined 78”;
alarmText[79]=”Not defined 79”;
alarmText[80]=”Vres Absent”;
alarmText[81]=”Source V too low transfert”;
alarmText[82]=”Source V too high transfert”;
alarmText[83]=”Vres out of range”;
alarmText[84]=”Source V too low stop”;
alarmText[85]=”Source V too high stop”;
alarmText[86]=”Source frequ too low”;
alarmText[87]=”Source frequ too high”;
alarmText[88]=”Not defined 88”;
alarmText[89]=”Not defined 89”;
alarmText[90]=”Not defined 90”;
alarmText[91]=”Not defined 91”;
alarmText[92]=”Not defined 92”;
alarmText[93]=”Not defined 93”;
alarmText[94]=”Not defined 94”;
alarmText[95]=”Not defined 95”;
alarmText[96]=”Not defined 96”;

55 – Agil Modular UPS – User manual – v7.2

//out
alarmText[97]=”Start”;
alarmText[98]=”Temperature derating”;
alarmText[99]=”Temperature too high”;
alarmText[100]=”Temperature sensor fail”;
alarmText[101]=”Auto-calib error”;
alarmText[102]=”Overload not ready”;
alarmText[103]=”Overload”;
alarmText[104]=”Power derating”;
alarmText[105]=”Vout too Low”;
alarmText[106]=”Overload too long”;
alarmText[107]=”Vout modify”;
alarmText[108]=”Load-sharing low”;
alarmText[109]=”Load-sharing high”;
alarmText[110]=”Mode support”;
alarmText[111]=”Igbt driver alarm”;
alarmText[112]=”Not defined 112”;
alarmText[113]=”Driver not ready”;
alarmText[114]=”Driver fault”;
alarmText[115]=”Over-current”;
alarmText[116]=”Igbt error”;
alarmText[117]=”Vout pi2 error”;
alarmText[118]=”Vout mpi2 error”;
alarmText[119]=”Off (bus)”;
alarmText[120]=”Backfeed error”;
alarmText[121]=”Too many start”;
alarmText[122]=”Out fuse open”;
alarmText[123]=”Not defined 123”;
alarmText[124]=”Not defined 124”;
alarmText[125]=”Not defined 125”;
alarmText[126]=”Not defined 126”;
alarmText[127]=”Not defined 127”;
alarmText[128]=”Not defined 128”;

56 – Agil Modular UPS – User manual – v7.2

//monitoring
alarmText[129]=”MBP Engaged”;
alarmText[130]=”Surge Arrester”;
alarmText[131]=”Redundancy Lost”;
alarmText[132]=”System Saturated”;
alarmText[133]=”Main Source Lost”;
alarmText[134]=”Secondary Source Lost”;
alarmText[135]=”Not defined”;
alarmText[136]=”Log Nearly Full”;
alarmText[137]=”Missing Module”;
alarmText[138]=”Aux Power Supply Fail”;
alarmText[139]=”New Module Detected”;
alarmText[140]=”Log cleared”;
alarmText[141]=”Config Modified”;
alarmText[142]=”System started”;
alarmText[143]=”DigIn 3”;
alarmText[144]=”DigIn 4”;
alarmText[145]=”DigIn 5”;
alarmText[146]=”DigIn 6”;
alarmText[147]=”DigIn 7”;
alarmText[148]=”DigIn 8”;
alarmText[149]=”Not defined”;
alarmText[150]=”Log Full”;
alarmText[151]=”Module Off Detected”;
alarmText[152]=”Module KO Detected”;
alarmText[153]=”DigIn 1”;
alarmText[154]=”DigIn 2”;
alarmText[155]=”Redundancy Plus 1 Lost”;
alarmText[156]=”Not defined”;
alarmText[157]=”Not defined”;
alarmText[158]=”Not defined”;
alarmText[159]=”Not defined”;
alarmText[160]=”Not defined”;

57 – Agil Modular UPS – User manual – v7.2

//battery
alarmText[417]=”Discharge”;
alarmText[418]=”Charging Fail”;
alarmText[419]=”Boost Active”;
alarmText[420]=”Test Active”;
alarmText[421]=”Fault”;
alarmText[422]=”Voltage Prealarm”;
alarmText[423]=”Voltage Alarm”;
alarmText[424]=”Voltage End Of Autonomy”;
alarmText[425]=”Capacity Prealarm”;
alarmText[426]=”Capacity Alarm”;
alarmText[427]=”Capacity End Of Autonomy”;
alarmText[428]=”Overvoltage”;
alarmText[429]=”Unknown Capacity”;
alarmText[430]=”Temp sensor fail”;
alarmText[431]=”Over temperature”;
alarmText[432]=”Limited Charging”;
alarmText[433]=”Boost Trig Stop Duration”;
alarmText[434]=”Not defined”;
alarmText[435]=”Not defined”;
alarmText[436]=”Not defined”;
alarmText[437]=”Not defined”;
alarmText[438]=”Not defined”;
alarmText[439]=”Not defined”;
alarmText[440]=”Not defined”;
alarmText[441]=”Not defined”;
alarmText[442]=”Not defined”;
alarmText[443]=”Not defined”;
alarmText[444]=”Not defined”;
alarmText[445]=”Not defined”;
alarmText[446]=”Not defined”;
alarmText[447]=”Not defined”;
alarmText[448]=”Not defined”;

58 – Agil Modular UPS – User manual – v7.2

ANNEXE 4 FAQ
How can I reset my admin password if I have unfortunately forgotten it?
Before version 3.1, there is a generic password that always works: 123TEC. You can use it to connect and change your expert
password. As this has been identified as a potential risk for system integrity, we strongly recommend to update to a newer version
where security has been improved.
From version 3.1, in case of password loss, a new temporary password (valid 24 hrs after creation) can be issued by CE+T Power.
To receive a temporary password, send an email with your T4S serial Number and the date at which you expect to go back on
site to change the password to [email protected] specifically requesting a new temporary password. The serial
number can be found on the sticker on the T4S, or on screen in ‘Parameters’ then ‘Info’.

59 – Agil Modular UPS – User manual – v7.2

60 – Agil Modular UPS – User manual – v7.2