Industrial Diesel Generator Set – KD1650-F

50 Hz – Fuel Consumption Optimized

RATINGS 400 V - 50 Hz
Standby kVA 1650
KWe 1320
Prime kVA 1500
KWe 1200

Benefits & features GENERAL SPECIFICATIONS

Engine brand KOHLER
KOHLER premium quality
 KOHLER provides one source responsibility for the Alternator commercial brand KOHLER
generating system and accessories Voltage (V) 400/230
 The generator set, its components and a wide range of Performance class G3
options have been fully developed, prototype tested,
One step load acceptance (out of ISO 100%
factory built, and production-tested criteria)
 The generator sets are designed in accordance to Standard Control Panel M80-D DEC4000 APM403 APM802
ISO8528-5 performance class G3 and accepts rated load
Genset Fuel consumption PRP ESP
in one step
KOHLER premium performances Consumption @ 100% load (L/h) 308.20 335.60
Engines Engine optimisation F
 Low fuel consumption thanks to a high technology Type of Cooling Radiator
common rail injection engine
 A smaller footprint thanks to a high power density GENERATOR SETS RATINGS
 Low temperature starting capability
 Long maintenance interval Standby Rating Prime Rating
Alternator
Voltage PH Hz kWe kVA Amps kWe kVA
 Provide industry leading motor starting capability 415/240 3 50 1320 1650 2296 1200 1500
 Excitation system to permit sustained overcurrent > KD1650-F 400/230 3 50 1320 1650 1200 1500
2382
300% In, during 10 sec 380/220 3 50 1320 1650 2507 1200 1500
 Built with a class H insulation and IP23
Cooling Data Center Continuous (DCP) Power rating is the same as the prime rating
when a reliable grid is available
 A compact and complete solution using a mechanically
driven radiator fan
 High temperature and altitude product capacity, running POWER RATINGS DEFINITION: according to ISO8528-1 (2018-02
without power derating edition) and ISO-3046-1
Control panel Emergency Standby Power (ESP): The standby rating is applicable
The KOHLER wide controller range provide the reliability to varying loads for the duration of a power outage. There is no
and performances you expect from your equipment. You can overload capability for this rating. Average load factor is <85%.
program, manage and diagnose it easily and in an efficient Prime Power (PRP): At varying load, the number of generator set
way operating hours is unlimited. A 10% overload capacity is available
for one hour within 12 hour of operation. Average load factor
KOHLER worldwide support
is<75%.
 A standard three-year or 1000-hour limited warranty for
Data Center Continuous Power (DCP): At varying or constant
standby applications.
load, the number running hours is unlimited. 10% overload
 A standard two-year or 8700-hour limited warranty for
capacity is available for one hour within 12 hour of operation.
prime power applications.
For limited running time, continuous or other ratings details,
 A worldwide product support
consult your contact and obtain technical information for ratings
guidelines, complete ratings definitions, and site condition
derates.

Reference Conditions: 25°C Air Inlet Temperature, 40°C Fuel Inlet Temperature, 100 kPa Barometric Pressure; 10.7 g/kg of dry air Humidity. Intake Restriction
set to maximum allowable limit for clean filter; Exhaust Back pressure set to maximum allowable limit. For particular conditions in your installation, refer to
factory for derating performance.
Data was taken from a single engine test according to the test methods, fuel specification and reference conditions stated above and is subjected to
instrumentation and engine-to-engine variability. Test conducted with alternate test methods, instrumentation, fuel or reference conditions can yield
different results. Data and specifications subject to change without notice.
GBD5-10016 (KD1650-F) 09/18
 Industrial Diesel Generator Set – KD1650-F
50 Hz – Fuel Consumption Optimized

KOHLER DIESEL ENGINE

General Lubrication System

Engine brand KOHLER Oil system capacity including filters (L) 180
Engine ref. KD45V20-5DFS (Standby) Min. oil pressure (bar) 3.50
Distribution 4 Strokes Max. oil pressure (bar) 6.50
Air inlet system Turbo Oil sump capacity (L) 180
Fuel Disesel Oil cooler Plate Exchanger
Engine optimization F Oil consumption 100% ESP (L/h) 0.17
Cylinders configuration V Air Intake System
Number of cylinders 20 Max. intake restriction (mm H2O) 510
Displacement (L) 44.95 Intake air flow (L/s) 1501.17
Bore (mm) * Stroke (mm) 135 * 157 Exhaust System
Compression ratio 15 : 1 Heat rejection to exhaust (kW) 1020
Speed (RPM) 1500 PRP ESP
Maximum stand-by power at rated RPM (kW) 1463 Exhaust gas temperature (°C) 503 496
Cylinder Head Material Cast Iron Exhaust gas flow (L/s) 3772 4096
Crankshaft Material Steel Max. exhaust back pressure (mm H2O) 867
Intake and Exhaust Valve Material Steel Radiator Charge Air Cooling System
Piston type & material Steel Ambient temperature design (°C) 40
Charge Air coolant Air/Air DC Radiated heat to ambient (kW) 103
Frequency regulation, steady state (%) +/- 0.25% CAC Heat Rejection (kW) 315
Injection Type Direct Heat rejection to coolant HT (kW) 576
Governor type Electronic Radiator & Engine capacity (L) 264
ECU type KODEC Coolant capacity HT, engine only (L) 143
Air cleaner type, models Dry Flow on the HT circuit at 0.7Bars pressure drop off
1952
Fuel System engine (L/min)
105
Maximum fuel pump flow (L/h) 470 Maximum Coolant temp without derating (°C)
Outlet coolant temperature (°C) 100
Fuel Inlet Minimum recommended size (mm) 19.05
Type of coolant Gencool
Fuel Outlet Minimum recommended size (mm) 9.53
Compressor Discharge Temp at 25°C (°C) 211
Max. restriction at fuel pump (m) 3.50
Thermostat begin of opening HT (°C) 82
Max head on fuel return line (m) 3.10
Maximum allowed inlet fuel temperature (°C) 60 Thermostat end of opening HT (°C) 92

Consumption with cooling system PRP ESP Fan power (kW) 37.60

Consumption @ 100% load (L/h) 308.20 335.60 Fan air flow w/o restriction (m3/s) 26
Consumption @ 75% load (L/h) 231.20 252.10 Available restriction on air flow (mm H2O) 30
Consumption @ 50% load (L/h) 157.20 171.30
Consumption @ 25% load (L/h) 85.60 93

Reference Conditions: 25°C Air Inlet Temperature, 40°C Fuel Inlet Temperature, 100 kPa Barometric Pressure; 10.7 g/kg of dry air Humidity. Intake Restriction
set to maximum allowable limit for clean filter; Exhaust Back pressure set to maximum allowable limit. For particular conditions in your installation, refer to
factory for derating performance.
Data was taken from a single engine test according to the test methods, fuel specification and reference conditions stated above and is subjected to
instrumentation and engine-to-engine variability. Test conducted with alternate test methods, instrumentation, fuel or reference conditions can yield
different results. Data and specifications subject to change without notice.
GBD5-10016 (KD1650-F) 09/18
 Industrial Diesel Generator Set – KD1650-F
50 Hz – Fuel Consumption Optimized

Alternator Specifications Alternator Standard Features

Alternator commercial brand KOHLER - All models are brushless, rotating-field alternators
Alternator ref. KH03850T
Number of pole 4 - NEMA MG1, IEEE, and ANSI standards compliance for
temperature rise and motor starting
Number of bearing Single Bearing
Technology Brushless - The AVR voltage regulator provides superior short
circuit capability
Indication of protection IP23
Insulation class H - Self-ventilated and dip proof construction
Winding type 12
- Sustained short-circuit current of up to 300% of the
Capacity for maintaining short rated current for up to 10 seconds
Yes
circuit at 3 ln for 10 s
AVR Regulation Yes - Superior voltage waveform
Coupling Direct
Application Data
Overspeed (rpm) 2250 Note: See Alternator Data Sheets for alternator application data
Power factor (Cos Phi) 0.80 and ratings, efficiency curves, voltage dip with motor starting
Voltage regulation at established curves, and short circuit decrement curves.
0.50
rating (+/- %)
Wave form : NEMA=TIF <40
Wave form : CEI=FHT <2
Total Harmonic Distortion in no-load
2.5
DHT (%)
Total Harmonic Distortion, on load
3.0
DHT (%)
Recovery time (Delta U = 20%
200
transient) (ms)
Performance Data
Continuous Nominal Rating 40°C
1500
(kVA)
Unbalanced load acceptance ratio
100
(%)
Peak motor starting (kVA) based on x% voltage dip power factor at 0.3

Reference Conditions: 25°C Air Inlet Temperature, 40°C Fuel Inlet Temperature, 100 kPa Barometric Pressure; 10.7 g/kg of dry air Humidity. Intake Restriction
set to maximum allowable limit for clean filter; Exhaust Back pressure set to maximum allowable limit. For particular conditions in your installation, refer to
factory for derating performance.
Data was taken from a single engine test according to the test methods, fuel specification and reference conditions stated above and is subjected to
instrumentation and engine-to-engine variability. Test conducted with alternate test methods, instrumentation, fuel or reference conditions can yield
different results. Data and specifications subject to change without notice.
GBD5-10016 (KD1650-F) 09/18
 Industrial Diesel Generator Set – KD1650-F
50 Hz – Fuel Consumption Optimized

Dimensions compact version

Length (mm) * Width (mm) * Height (mm) 5090* 2122 * 2480

Dry weight (kg) 10100
Tank capacity (L) 465

* Sound levels in dB(A) are given at 75% Prime Power

Container dimensions ISO20 version

ISO20 Si
Length (mm) * Width (mm) * Height (mm) 6058* 2438 * 2896
Dry weight (kg) 15900
Tank capacity (L) 465
Acoustic pressure level @1m in dB(A) 97
Measured acoustic power level (Lwa) 118
Acoustic pressure level @7m in dB(A) 88
* Sound levels in dB(A) are given at 75% Prime Power

Container dimensions ISO20 super soundproofed version

ISO20 SSi
Length (mm) * Width (mm) * Height (mm) 9140* 2438 * 2896
Dry weight (kg) 16500
Tank capacity (L) 465
Acoustic pressure level @1m in dB(A) 81
Measured acoustic power level (Lwa) 102.90
Acoustic pressure level @7m in dB(A) 72
* Sound levels in dB(A) are given at 75% Prime Power

Reference Conditions: 25°C Air Inlet Temperature, 40°C Fuel Inlet Temperature, 100 kPa Barometric Pressure; 10.7 g/kg of dry air Humidity. Intake Restriction
set to maximum allowable limit for clean filter; Exhaust Back pressure set to maximum allowable limit. For particular conditions in your installation, refer to
factory for derating performance.
Data was taken from a single engine test according to the test methods, fuel specification and reference conditions stated above and is subjected to
instrumentation and engine-to-engine variability. Test conducted with alternate test methods, instrumentation, fuel or reference conditions can yield
different results. Data and specifications subject to change without notice.
GBD5-10016 (KD1650-F) 09/18
 Industrial Diesel Generator Set – KD1650-F
50 Hz – Fuel Consumption Optimized

The M80-D can be used as a basic terminal block for connecting an electrical
M80-D cabinet box and as an instrument panel with a highly intuitive LCD screen giving
an overview of your generating set's basic parameters:
- Oil gauge
- coolant temperature
- oil temperature
- engine speed
- battery voltage
- charge air temperature
- fuel consumption
- etc.

The engine main functions can be controlled and events are recorded to facilitate
diagnostics:
- starting
- speed adjustment
- stopping
- droop
- etc.

ERGONOMIC AND USER FRIENDLY

Large display screen,
DEC4000 buttons and scroll wheel,
Electrical measurements: voltmeter, frequency meter, ampmeter, voltage.
Engine parameters: working hours counter, oil pressure, coolant temperature,
fuel level, engine speed, battery
Alarms and faults: oil pressure, coolant temperature, failure to start, overspeed,
alternator min/max., battery voltage min. /max., emergency stop, fuel level.
Ergonomics: wheel for navigating around the various menus.
Communication: remote control and operation software,
USB connections, PC connection.
For more information on the product and its options, please refer to the sales
documentation

BASIC GENERATING SET AND POWER PLANT CONTROL

The APM403 is a versatile control unit which allows operation in manual or
APM403 automatic mode
- Measurements : voltage and current
- kW/kWh/kVA power meters
- Standard specifications: Voltmeter, Frequency meter.
- Optional : Battery ammeter.
- J1939 CAN ECU engine control
- Alarms and faults: Oil pressure, Coolant temperature, Overspeed,
Start-up failure, alternator min/max, Emergency stop button.
- Engine parameters: Fuel level, hour counter, battery voltage.
- Optional (standard at 24V): Oil pressure, water temperature.
- Event log/ Management of the last 300 genset events.
- Mains and genset protection
- Clock management
- USB connections, USB Host and PC,
- Communications : RS485 INTERFACE
- ModBUS protocol/SNMP
- Optional : Ethernet, GPRS, remote control, 3G, 4G,
- Websupervisor, SMS, E-mails

Reference Conditions: 25°C Air Inlet Temperature, 40°C Fuel Inlet Temperature, 100 kPa Barometric Pressure; 10.7 g/kg of dry air Humidity. Intake Restriction
set to maximum allowable limit for clean filter; Exhaust Back pressure set to maximum allowable limit. For particular conditions in your installation, refer to
factory for derating performance.
Data was taken from a single engine test according to the test methods, fuel specification and reference conditions stated above and is subjected to
instrumentation and engine-to-engine variability. Test conducted with alternate test methods, instrumentation, fuel or reference conditions can yield
different results. Data and specifications subject to change without notice.
GBD5-10016 (KD1650-F) 09/18
 Industrial Diesel Generator Set – KD1650-F
50 Hz – Fuel Consumption Optimized

ADVANCED POWER PLANT MANAGEMENT CONTROL

Dedicated to power plant management APM802 provides advanced control,
APM802 system monitoring, and system diagnostics for optimum performance and
compatibility
- Graphic display with touchscreen
- User language selectable
- Specially researched ergonomics
- High level of equipment availability
- USB and Ethernet ports
- Modbus protocol
- Making it easy to extend the installation
- Complies with the international standard IEC 61131-3

Reference Conditions: 25°C Air Inlet Temperature, 40°C Fuel Inlet Temperature, 100 kPa Barometric Pressure; 10.7 g/kg of dry air Humidity. Intake Restriction
set to maximum allowable limit for clean filter; Exhaust Back pressure set to maximum allowable limit. For particular conditions in your installation, refer to
factory for derating performance.
Data was taken from a single engine test according to the test methods, fuel specification and reference conditions stated above and is subjected to
instrumentation and engine-to-engine variability. Test conducted with alternate test methods, instrumentation, fuel or reference conditions can yield
different results. Data and specifications subject to change without notice.
GBD5-10016 (KD1650-F) 09/18
 Industrial Diesel Generator Set – KD1650-F
50 Hz – Fuel Consumption Optimized

STANDARD SCOPE OF SUPPLY

All our KD Series gensets are fitted with:

- Industrial water cooled DIESEL engine

- Radiator with coolant
- Electric starter & charge alternator 24 V D.C
- Electronic governor
- Standard air filter
- Single bearing alternator IP 23 T° rise/ insulation to class H/H
- Welded steel base frame with 80% vibration attenuation mounts
- Flexible fuel lines & lub oil drain pump
- Fuel water separator filter
- Exhaust outlet with flexible and flanges
- M80 control panel
- User’s manual (1 copy)
- Packing under plastic film
- Delivered with oil
- Delivered with antifreeze liquid

CODES AND STANDARDS

Engine-generators set is designed and manufactured in facilities certified to standards ISO9001:2015 & ISO14001:2015. The generator sets and
its components are prototype-tested, factory built and production tested and are in compliance with the relevant standards:

- Machinery Directive 2006/42/EC of May 17th 2006

- EMC Directive2014/30/UE
- Safety objectives set out in the Low Voltage Directive 2014/35/UE
- EN ISO 8528-13, EN 60034-1, EN 61000-6-1, EN 61000-6-2, EN 61000-6-3, EN 55011, EN 1679-1 et EN 60204-1

TERMS OF USE
According to the standard, the nominal power assigned by the genset is given for 25°C Air Intlet Temperature, of a barometric pressure of
100 kPA (100 m A.S.L), and 30 % relative humidity. For particular conditions in your installation, refer to factory for derating performance.

WARRANTY INFORMATION
Standard Warranty for Stand-by application:
- Three (3) years from registered start-up or one thousand (1000) hours limited warranty, whichever occurs first
- In any event, the warranty period will expire not later than fifty-four (54) months from date of shipment from factory

Standard Warranty for Prime application:

- Two (2) years from registered start-up or eight thousand and seven hundred (8700) hours limited warranty,
whichever occurs first
- In any event, the warranty period will expire not later than forty-two (42) months from date of shipment from factory
For more details regarding conditions of application and scope of the warranty please refer to our General “terms & conditions of sales”.

Reference Conditions: 25°C Air Inlet Temperature, 40°C Fuel Inlet Temperature, 100 kPa Barometric Pressure; 10.7 g/kg of dry air Humidity. Intake Restriction
set to maximum allowable limit for clean filter; Exhaust Back pressure set to maximum allowable limit. For particular conditions in your installation, refer to
factory for derating performance.
Data was taken from a single engine test according to the test methods, fuel specification and reference conditions stated above and is subjected to
instrumentation and engine-to-engine variability. Test conducted with alternate test methods, instrumentation, fuel or reference conditions can yield
different results. Data and specifications subject to change without notice.
GBD5-10016 (KD1650-F) 09/18