Caterpillar Cat 329DL EXCAVATOR (Prefix JHJ) Service Repair Manual (JHJ00001 and Up) PDF

Service Repair Manual
Models
329DL EXCAVATOR
329D L Excavator JHJ00001-UP (MACHINE) POWERED BY C7 Engine(SEBP5372... 3/13
Tool Part Number Part Description Qty

A 1P-2420 Transmission Repair Stand 1
B 138-7573 Link Bracket 2
C 1P-1863 Retaining Ring Pliers 1
D 138-7575 Link Bracket 3
E 4C-8359 Eyebolt 2
F 138-7574 Link Bracket 2
G 138-7576 Link Bracket 2
Start By:
a. Start by removing the final drive. Refer to Disassembly and Assembly, "Final Drive -
Remove".
Note: Cleanliness is an important factor. Before the disassembly procedure, the exterior of
the component should be thoroughly cleaned. This will prevent dirt from entering the
internal mechanism.
1. Put an alignment mark across the sections of the final drive for assembly purposes. The
parts must be reinstalled to the original locations.
Illustration 1 g00892878
2. Use Tooling (G) and a suitable lifting device to position the final drive assembly onto
Tooling (A). The weight of the final drive assembly is approximately 550 kg (1200 lb).
3. Remove bolts (1).
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sisw... 2020/3/5
4. Use Tooling (B) and a suitable lifting device to remove cover (2). The weight of cover (2) is
approximately 32 kg (70 lb).
5. Remove bolts (3) and gear (4). Check plate (6). Replace plate (6) if plate (6) is worn.
Remove plugs (5) from cover (2).
6. Remove O-ring seals (7) from plugs (5).
7. Remove gear (8) and spacer (9).
8. Use Tooling (C) to remove retaining ring (10). Remove washer (11) and gear (12). Remove
bearing assembly (13) and washer (14).
9. Repeat Step 8 for the other two gear assemblies.
10. Remove retaining ring (15).
11. Remove carrier assembly (16).
12. Use a suitable press to remove the shafts from carrier assembly (16).
13. Remove gear (17) and spacer (18).
14. Use Tooling (D) and a suitable lifting device to remove planetary carrier (19). The weight of
planetary carrier (19) is approximately 48 kg (105 lb).
15. Remove retaining ring (21). Lift planetary carrier (19) off sun gear (20).
16. Drive spring pin (23) into planetary shaft (22).
17. Remove planetary shaft (22). Use a suitable punch to remove spring pin (23) from planetary
shaft (22).
18. Remove washers (24) and bearing (25) from planetary gear (26).
19. Repeat Steps 16 through 18 for the other two planetary gears.
20. Remove gear (27). Remove spacer (27A).
21. Use two people to remove carrier assembly (28). The weight of carrier assembly (28) is
22. Drive spring pin (30) into shaft (29).
23. Remove shaft (29). Use a suitable punch to remove spring pin (30) from shaft (29).
24. Remove washers (31) and bearings (32) from planetary gear (33).
25. Repeat Steps 22 through 24 for the other three planetary gears.
26. Fasten Tooling (E) and a suitable lifting device to ring gear (34), as shown. Remove ring
gear (34) from sprocket housing (35). The weight of ring gear (34) is approximately 66 kg
(146 lb).
27. Remove O-ring seal (36) from sprocket housing (35).
28. Remove bolts (37) from coupling gear (38).
29. Install suitable forcing bolts (39) in coupling gear (38). Tighten the forcing bolts evenly in
order to loosen coupling gear (38). Remove the coupling gear from the motor housing.
30. Remove shims (40) from the motor housing.
Note: Inner cones and outer bearing cones (42) are a slip fit on the motor housing. While
you remove sprocket housing (35) from the motor housing, inner bearing cone (42) may
stay with the sprocket housing or the inner bearing cone may stay on the motor housing.
31. Fasten Tooling (F) and a suitable lifting device to sprocket housing (35). Separate the
sprocket housing from the motor housing. The weight of sprocket housing (35) is
32. Remove the locating pins from the motor housing.
33. Remove Duo-Cone seal (41) from the motor housing.
34. If inner bearing cone (42) remained on the motor housing, then remove the inner bearing
cone.
35. Remove Duo-Cone seal (43) from the sprocket housing.
36. If inner bearing cone (42) remained on the sprocket housing, then remove the inner bearing
cone.
37. Remove the bearing cups from the sprocket housing.
Copyright 1993 - 2020 Caterpillar Inc. Thu Mar 5 00:38:31 UTC+0800 2020
All Rights Reserved.
Private Network For SIS Licensees.
Shutdown SIS
Previous Screen
Product: EXCAVATOR
Model: 329D L EXCAVATOR JHJ
Configuration: 329D L Excavator JHJ00001-UP (MACHINE) POWERED BY C7 Engine
Disassembly and Assembly

324D, 325D, 326D and 329D Excavators and 329D MHPU Mobile Hydraulic Power
Unit Machine Systems
Media Number -RENR8646-22 Publication Date -01/02/2015 Date Updated -12/09/2018
i03949150
Final Drive - Assemble

SMCS - 4050-016
S/N - A3R1-UP
S/N - AZP1-UP
S/N - BFC1-UP
S/N - BYS1-UP
S/N - CZF1-UP
S/N - DBH1-UP
S/N - DJF1-UP
S/N - DTZ1-UP
S/N - EBM1-UP
S/N - EJC1-UP
S/N - GBR1-UP
S/N - GPB1-UP
S/N - GPK1-UP
S/N - JAT1-UP
S/N - JHJ1-UP
S/N - JJG1-UP
S/N - JZR1-UP
S/N - KBE1-UP
S/N - LAB1-UP
S/N - LAL1-UP
S/N - MCL1-UP
S/N - MNB1-UP
S/N - MND1-UP
S/N - NAC1-UP
S/N - PJM1-UP
S/N - PKE1-UP
S/N - PYT1-UP
S/N - RSK1-UP
S/N - SCR1-UP
S/N - SYM1-UP
S/N - T2D1-UP
S/N - T2S1-UP
S/N - TPM1-UP
S/N - TRH1-UP
S/N - TSN1-UP
S/N - TZL1-UP
S/N - XDB1-UP
S/N - YFW1-UP
Assembly Procedure
Table 1
Required Tools
Tool Part Number Part Description Qty
A 1P-2420 Transmission Repair Stand 1

B 138-7573 Link Bracket 2
D 138-7574 Link Bracket 2
G 126-3994 Duo-Cone Seal Installer 1
H 5P-3931 Anti-Seize Compound
F 1U-8846 Gasket Sealant
Note: Cleanliness is an important factor. Before assembly, all parts should be cleaned in
cleaning fluid. Allow the parts to air dry. Wiping cloths or rags should not be used to dry
parts. Lint may be deposited on the parts which may cause later trouble. Inspect all parts. If
any parts are worn or damaged, use new parts for replacement. All disassembly and all
assembly procedures must be performed on a clean work surface and in a clean hydraulic
area. Keep cleaned parts covered and protected at all times.
Note: O-rings, gaskets, and seals should always be replaced. A used O-ring may not have
the same sealing properties as a new O-ring. Use 1U-6396 O-Ring Assembly Compound
during the assembly procedure.
Note: Apply a light film of hydraulic oil to all components before assembly.
1. Install the final drive sprocket if the sprocket was removed from the main housing.
2. Refer to Disassembly and Assembly, "Final Drive Sprocket - Remove and Install".
3. Apply Tooling (H) to the outer diameter of the bearings.
4. Install bearings (32) and (33) in main housing (18) with a suitable press.
5. Make sure that bearing (32) and bearing (33) contact the counterbore in the main housing.
6. Use the following procedure to preload the bearings and determine the correct thickness of
shims.
a. Fasten Tooling (D) and a suitable lifting device to main housing (18) . Install the main
housing on the motor housing.
b. Put the main housing and the motor housing in a suitable press.
(a) Bearing surface
(b) Housing surface
c. Use a suitable press and a spacer in order to apply a load of 4000 kg (8818.5 lb) on
the bearings. Rotate the housing in order to seat the bearings.
d. Reduce the load on the bearings to 1000 ± 100 kg (2204.6 ± 220.5 lb).
e. Use a depth micrometer in order to measure the step length between the bearing
surface and the housing surface. Take measurements at several different locations
around the housing. Compute the average of the measured dimensions and record the
number. Call this Dimension (Y) .
f. Use a depth micrometer in order to measure the step length of the coupling gear (26) .
Take measurements at several different locations around the gear. Compute the
average of the measured dimensions and record the number. Call this Dimension (X) .
g. The thickness of the shims is equal to (X - Y) ± 0.05 mm (0.002 inch).
Note: Use no more than two shims. If two shims are required, install the thinner shim
next to the gear.
h. Remove the main housing from the motor housing.
7. Use Tooling (G) in order to install Duo-Cone seal (31) in main housing (18) . Refer to
Disassembly and Assembly, "Duo-Cone Conventional Seals - Install".
Note: The rubber seals and all surfaces that contact the seals must be clean and dry. After
installation of the seals, put clean SAE 30 oil on the contact surfaces of the metal seals.
8. Use Tooling (G) in order to install Duo-Cone seal (29) in motor housing (28) .
9. Apply Tooling (H) to the surfaces that contact pins (30) .
10. Install alignment pins (30) .
Note: Do not damage the Duo-Cone seals in the main housing or in the motor housing
during the assembly of the two components. After installation of the main housing on the
motor housing, there will be a small gap between the components. The gap is caused by the
Duo-Cone seals. This gap will be eliminated during installation of gear (26) .
11. Fasten Tooling (D) and a suitable lifting device to main housing (18) . Install the main
housing on the motor housing.
12. Install shims (27) that were determined in Step 6.g in the main housing.
Note: If two shims are required, install the thinner shim next to the gear.
13. Install gear (26) .
14. Install bolts (25) in gear (26) . Install the bolts in an even pattern until the gear is seated
against the bearing. Tighten bolts (25) in a crisscross pattern.
15. Install O-ring seal (24) to main housing (18) .
16. Assemble carrier assembly (15) , as follows.
Thank you very much for
your reading. Please Click
Here. Then Get COMPLETE
MANUAL. NO WAITING
NOTE:
If there is no response to
click on the link above,
please download the PDF
document first and then
click on it.
a. Install bearings (22) in planetary gear (23) .
b. Install thrust washers (21) and planetary gear (23) in the carrier assembly.
c. Use a deburring tool in order to remove the metal burr from the openings in the
carrier. Install planetary shaft (19) in the carrier assembly.
d. Drive spring pin (20) into planetary shaft (19) with a hammer and a punch.
e. Orient the split in spring pin (20) vertically to the carrier. Align the split in the spring
pin to the top or to the bottom. Make a stake mark on each side of the spring pin hole
in the carrier. Each stake mark should be approximately 1.50 mm (0.059 inch) from
the outside diameter of the spring pin hole.
17. Repeat Steps 16.a through 16.e in order to install the remaining planetary gears in the carrier
assembly.
18. Install a lifting sling through the middle of carrier assembly (15) . Fasten a 12.7 mm (0.50
inch) shackle to the suitable lifting device.
19. Install carrier assembly (15) on the final drive. The weight of carrier assembly (15) is
20. Remove the shackle and the suitable lifting device.
21. Apply Tooling (F) to the mating surface of ring gear (17b) .
22. Install ring gear (17a) on ring gear (17b) .
23. Fasten a suitable lifting device to ring gears (17) , as shown. Install the ring gears to main
housing (18) . The weight of ring gears (17) is approximately 45 kg (100 lb).
24. Install spacer (16) in the carrier assembly.

Caterpillar Cat 329DL EXCAVATOR (Prefix JHJ) Service Repair Manual (JHJ00001 and Up) PDF

Uploaded by

Copyright:

Available Formats

Caterpillar Cat 329DL EXCAVATOR (Prefix JHJ) Service Repair Manual (JHJ00001 and Up) PDF

Uploaded by

Document Information

Original Title

Copyright

Available Formats

Share this document

Share or Embed Document

Sharing Options

Did you find this document useful?

Is this content inappropriate?

Copyright:

Available Formats

Caterpillar Cat 329DL EXCAVATOR (Prefix JHJ) Service Repair Manual (JHJ00001 and Up) PDF

Uploaded by

Copyright:

Available Formats

Service Repair Manual

Tool Part Number Part Description Qty

3. Remove bolts (1).

6. Remove O-ring seals (7) from plugs (5).

7. Remove gear (8) and spacer (9).

9. Repeat Step 8 for the other two gear assemblies.

10. Remove retaining ring (15).

11. Remove carrier assembly (16).

13. Remove gear (17) and spacer (18).

16. Drive spring pin (23) into planetary shaft (22).

20. Remove gear (27). Remove spacer (27A).

22. Drive spring pin (30) into shaft (29).

27. Remove O-ring seal (36) from sprocket housing (35).

28. Remove bolts (37) from coupling gear (38).

30. Remove shims (40) from the motor housing.

32. Remove the locating pins from the motor housing.

33. Remove Duo-Cone seal (41) from the motor housing.

35. Remove Duo-Cone seal (43) from the sprocket housing.

37. Remove the bearing cups from the sprocket housing.

Disassembly and Assembly

Final Drive - Assemble

A 1P-2420 Transmission Repair Stand 1

3. Apply Tooling (H) to the outer diameter of the bearings.

(a) Bearing surface

(b) Housing surface

g. The thickness of the shims is equal to (X - Y) ± 0.05 mm (0.002 inch).

h. Remove the main housing from the motor housing.

9. Apply Tooling (H) to the surfaces that contact pins (30) .

10. Install alignment pins (30) .

13. Install gear (26) .

15. Install O-ring seal (24) to main housing (18) .

16. Assemble carrier assembly (15) , as follows.

a. Install bearings (22) in planetary gear (23) .

20. Remove the shackle and the suitable lifting device.

22. Install ring gear (17a) on ring gear (17b) .

24. Install spacer (16) in the carrier assembly.

You might also like