Branch 1
version 12.4
no service timestamps log datetime msec
no service timestamps debug datetime msec
no service password-encryption
hostname Branch1
no ip domain-lookup
!
!
interface FastEthernet0/0
ip address 192.168.9.65 255.255.255.224
duplex auto
speed auto
interface FastEthernet0/1
ip address 192.168.9.97 255.255.255.224
duplex auto
speed auto
interface Serial0/0/0
ip address 192.168.9.158 255.255.255.224
clock rate 64000
interface Serial0/0/1
no ip address
shutdown
interface FastEthernet0/1/0
shutdown
interface FastEthernet0/1/1
shutdown
interface FastEthernet0/1/2
shutdown
interface FastEthernet0/1/3
shutdown
interface Vlan1
no ip address
shutdown
ip classless
ip route 192.168.9.192 255.255.255.224 Serial0/0/0
line con 0
line vty 0 4
login
end
Branch1#conf
Branch1#configure te
Branch1#configure terminal
Enter configuration commands, one per line. End with CNTL/Z.
Branch1(config)#ip rou
Branch1(config)#ip route 192.168.9.0 255.255.255.224 s 0/0/0
Branch1(config)#do wr
Building configuration...
[OK]
Branch1(config)#
Branch1(config)#exit
Branch1#
%SYS-5-CONFIG_I: Configured from console by console
Branch1#tracer 192.168.9.0
Type escape sequence to abort.
Tracing the route to 192.168.9.0
1 192.168.9.129 32 msec 31 msec 31 msec
2 192.168.9.129 !H * !H
3 * *
Branch1#tracer 192.168.9.30
Type escape sequence to abort.
Tracing the route to 192.168.9.30
1 192.168.9.129 31 msec 32 msec 31 msec
2 * * *
3 * * *
4 * * *
5 * * *
6 * * *
7 * * *
8 * * *
9 * * *
10 * * *
11 * * *
12 * * *
13 * *
Branch1#show ip int
Branch1#show ip interface b
Branch1#show ip interface brief
Interface IP-Address OK? Method Status Protocol
FastEthernet0/0 192.168.9.65 YES manual up up
FastEthernet0/1 192.168.9.97 YES manual up up
Serial0/0/0 192.168.9.158 YES manual up up
Serial0/0/1 unassigned YES unset administratively down down
FastEthernet0/1/0 unassigned YES unset administratively down down
FastEthernet0/1/1 unassigned YES unset administratively down down
FastEthernet0/1/2 unassigned YES unset administratively down down
FastEthernet0/1/3 unassigned YES unset administratively down down
Vlan1 unassigned YES unset administratively down down
Branch1#show arp
Protocol Address Age (min) Hardware Addr Type Interface
Internet 192.168.9.65 - 000C.8572.8101 ARPA FastEthernet0/0
Internet 192.168.9.97 - 000C.8572.8102 ARPA FastEthernet0/1
Branch1#sh run
Branch1#sh running-config
Building configuration...
Current configuration : 898 bytes
version 12.4
no service timestamps log datetime msec
no service timestamps debug datetime msec
no service password-encryption
hostname Branch1
!
!
no ip domain-lookup
interface FastEthernet0/0
ip address 192.168.9.65 255.255.255.224
duplex auto
speed auto
interface FastEthernet0/1
ip address 192.168.9.97 255.255.255.224
duplex auto
speed auto
interface Serial0/0/0
ip address 192.168.9.158 255.255.255.224
clock rate 64000
interface Serial0/0/1
Branch1#ing 192.168.9.65
% Invalid input detected at '^' marker.
Branch1#ping 192.168.9.65
Type escape sequence to abort.
Sending 5, 100-byte ICMP Echos to 192.168.9.65, timeout is 2 seconds:
!!!!!
Success rate is 100 percent (5/5), round-trip min/avg/max = 0/9/16 ms
Branch1#ping 192.168.9.
Branch1#
Branch 2
%LINEPROTO-5-UPDOWN: Line protocol on Interface FastEthernet0/0, changed state to up
Router(config-if)#exit
Router(config-if)#exit
Router(config)#exit
Router#
%SYS-5-CONFIG_I: Configured from console by console
Router#configure t
Router#configure terminal
Enter configuration commands, one per line. End with CNTL/Z.
Router(config)#inter
Router(config)#interface fas
Router(config)#interface fastEthernet
% Incomplete command.
Router(config)#interface fastEthernet 0/1
Router(config-if)#ip ad
Router(config-if)#ip address 192.168.9.1 255.255.255.224
Router(config-if)#no shut
Router(config-if)#no shutdown
%LINK-5-CHANGED: Interface FastEthernet0/1, changed state to up
%LINEPROTO-5-UPDOWN: Line protocol on Interface FastEthernet0/1, changed state to up
Router(config-if)#
Router(config-if)#exit
Router(config)#exit
Router#
%SYS-5-CONFIG_I: Configured from console by console
Router#conf
Router#configure ter
Router#configure terminal
Enter configuration commands, one per line. End with CNTL/Z.
Router(config)#inter
Router(config)#interface serial
Router(config)#interface serial 0/0/1
Router(config-if)#ip add
Router(config-if)#ip address 192.168.9.190 255.255.255.224
Router(config-if)#no shut
Router(config-if)#no shutdown
%LINK-5-CHANGED: Interface Serial0/0/1, changed state to up
Router(config-if)#
%LINEPROTO-5-UPDOWN: Line protocol on Interface Serial0/0/1, changed state to up
Router(config-if)#do wr
Building configuration...
[OK]
Router(config-if)#
Router(config-if)#
Router con0 is now available
Press RETURN to get started.
Router>ena
Router#show r
Router#show running-config
Building configuration...
Current configuration : 852 bytes
version 12.4
no service timestamps log datetime msec
no service timestamps debug datetime msec
no service password-encryption
hostname Router
!
!
interface FastEthernet0/0
ip address 192.168.9.33 255.255.255.224
duplex auto
speed auto
interface FastEthernet0/1
ip address 192.168.9.1 255.255.255.224
duplex auto
speed auto
interface Serial0/0/0
no ip address
shutdown
interface Serial0/0/1
ip address 192.168.9.190 255.255.255.224
interface FastEthernet0/1/0
switchport mode access
shutdown
interface FastEthernet0/1/1
switchport mode access
shutdown
interface FastEthernet0/1/2
switchport mode access
shutdown
interface FastEthernet0/1/3
switchport mode access
shutdown
interface Vlan1
no ip address
shutdown
ip classless
!
!
line con 0
line vty 0 4
login
end
Router#ping 192.168.0.30
Type escape sequence to abort.
Sending 5, 100-byte ICMP Echos to 192.168.0.30, timeout is 2 seconds:
....
Success rate is 0 percent (0/5)
Router#ping 192.168.9.30
Type escape sequence to abort.
Sending 5, 100-byte ICMP Echos to 192.168.9.30, timeout is 2 seconds:
!!!!!
Success rate is 100 percent (5/5), round-trip min/avg/max = 47/59/63 ms
Router#conf
Router#configure ter
Router#configure terminal
Enter configuration commands, one per line. End with CNTL/Z.
Router(config)#ip rou
Router(config)#ip route 192.168.9.64 255.255.255.224 s0/01
%Invalid interface type and number
Router(config)#ip route 192.168.9.64 255.255.255.224 s0/0/1
Router(config)#wr
% Invalid input detected at '^' marker.
Router(config)#do wr
Building configuration...
[OK]
Router(config)#
Router#
%SYS-5-CONFIG_I: Configured from console by console
Router#
Hq
%LINEPROTO-5-UPDOWN: Line protocol on Interface FastEthernet0/0, changed state to up
Router(config-if)#exit
Router(config-if)#exit
Router(config)#exit
Router#
%SYS-5-CONFIG_I: Configured from console by console
Router#configure t
Router#configure terminal
Enter configuration commands, one per line. End with CNTL/Z.
Router(config)#inter
Router(config)#interface fas
Router(config)#interface fastEthernet
% Incomplete command.
Router(config)#interface fastEthernet 0/1
Router(config-if)#ip ad
Router(config-if)#ip address 192.168.9.1 255.255.255.224
Router(config-if)#no shut
Router(config-if)#no shutdown
%LINK-5-CHANGED: Interface FastEthernet0/1, changed state to up
%LINEPROTO-5-UPDOWN: Line protocol on Interface FastEthernet0/1, changed state to up
Router(config-if)#
Router(config-if)#exit
Router(config)#exit
Router#
%SYS-5-CONFIG_I: Configured from console by console
Router#conf
Router#configure ter
Router#configure terminal
Enter configuration commands, one per line. End with CNTL/Z.
Router(config)#inter
Router(config)#interface serial
Router(config)#interface serial 0/0/1
Router(config-if)#ip add
Router(config-if)#ip address 192.168.9.190 255.255.255.224
Router(config-if)#no shut
Router(config-if)#no shutdown
%LINK-5-CHANGED: Interface Serial0/0/1, changed state to up
Router(config-if)#
%LINEPROTO-5-UPDOWN: Line protocol on Interface Serial0/0/1, changed state to up
Router(config-if)#do wr
Building configuration...
[OK]
Router(config-if)#
Router(config-if)#
Router con0 is now available
Press RETURN to get started.
Router>ena
Router#show r
Router#show running-config
Building configuration...
Current configuration : 852 bytes
version 12.4
no service timestamps log datetime msec
no service timestamps debug datetime msec
no service password-encryption
hostname Router
!
!
interface FastEthernet0/0
ip address 192.168.9.33 255.255.255.224
duplex auto
speed auto
interface FastEthernet0/1
ip address 192.168.9.1 255.255.255.224
duplex auto
speed auto
interface Serial0/0/0
no ip address
shutdown
interface Serial0/0/1
ip address 192.168.9.190 255.255.255.224
interface FastEthernet0/1/0
switchport mode access
shutdown
interface FastEthernet0/1/1
switchport mode access
shutdown
interface FastEthernet0/1/2
switchport mode access
shutdown
interface FastEthernet0/1/3
switchport mode access
shutdown
interface Vlan1
no ip address
shutdown
!
ip classless
line con 0
line vty 0 4
login
end
Router#ping 192.168.0.30
Type escape sequence to abort.
Sending 5, 100-byte ICMP Echos to 192.168.0.30, timeout is 2 seconds:
....
Success rate is 0 percent (0/5)
Router#ping 192.168.9.30
Type escape sequence to abort.
Sending 5, 100-byte ICMP Echos to 192.168.9.30, timeout is 2 seconds:
!!!!!
Success rate is 100 percent (5/5), round-trip min/avg/max = 47/59/63 ms
Router#conf
Router#configure ter
Router#configure terminal
Enter configuration commands, one per line. End with CNTL/Z.
Router(config)#ip rou
Router(config)#ip route 192.168.9.64 255.255.255.224 s0/01
%Invalid interface type and number
Router(config)#ip route 192.168.9.64 255.255.255.224 s0/0/1
Router(config)#wr
% Invalid input detected at '^' marker.
Router(config)#do wr
Building configuration...
[OK]
Router(config)#
Router#
%SYS-5-CONFIG_I: Configured from console by console
Router#
