SCON Valves, Catalogue E10 PDF

[email protected] | [email protected].
pk
www.sconvalve.com.pk
1
[email protected] | [email protected]
Notes:
 THIS IS THE NEW CATALGOUE E10, REPLACING THE OLD CATALGOUES OF 2013, 2014 & 2015
 THE FIGURE NUMBERS ARE REMAIN UNCHANGED AS MENTIONED IN PREVIOUS PRINTED CATALOGUES
 SO FAR, ONLY THE SOFT COPY IS AVIALABLE FOR SHARING, HARD COPIES WILL BE SHARED ONCE AVAILABE IN PRINTED HARD COPIES
 PLEASE IGNORE IF ANY ERROR FOUND & CONTACT TO FOLLOWING EMAIL ADDRESS FOR CLERIFICATION
 CATALOGUE E10 MAY SUBMIT FOR TECHNICAL SUBMITTAL APPROVAL, TILL THE HARD COPIES ARE NOT AVAILABLE
 CATALOGUE 2015 MAY SUBMIT IF HARD COPIES OF TECHNCIAL SUBMITTAL REQUIRE, TILL THE CATALOGUE E10 IS NOT AVIALABLE IN HARD COPIES
INCASE OF ANY QUESTION, PELASE WRITE TO: [email protected]
2
3
High Quality - Most Reliable - Most Economical
Actual Photo
SCON Valves & Castings are produced in our own facilities used exclusively for
manufacturing, where each phase of production verifies from selection of raw
materials to casting, machining, assembly & pressure testing.
SAFCO’s corporate strategy to apply the most advance procedures exclusively

used for manufacturing of SCON Valves & SCON Castings with special emphasis
on quality, safety & reliability and most of all long service life.
SCON ensure the highest possible quality with the use of high quality raw materials
& advanced manufacturing technology & importantly the world’s most advance
foundry technology, SCON is strongly committed to defend our market position &
aggressively competing all other valves.
SCON production facilities are located in Lahore - Pakistan & the international
airport is about 10 minutes’ drive from our production facilities.
Actual Photo
Machining- having more than 40+ machines including CNC, which ensure the
high quality machining of valves as well as we have in-house testing facilities
equipped with advanced hydrostatic testing bench, ultrasonic thickness testing,
brunel hardness testing.
Advantages-
 Sizes availability DN15 - DN900

 Availability of complete range of valves
 Warranty 36 months - free replacement
 Lowest possible rates - In time deliveries
 Material compositions in Cast Iron, Ductile Iron & Cast Steel
 Complete technical support & after sales service
 Pressure ratings from PN16 to PN40 & Class 125 to Class 300
Actual Photo
Foundry- world’s most advanced & first of its kind foundry plant in Pakistan, the
chemically bonded foundry, currently known as the most advance casting process
with the advantages of casting quality remain perfect, exact wall thicknesses and
weights & remain free from the porosity, pin holes & blow holes.
Sale Conditions- The products sold are guaranteed and free from manufacturing
defects for the term of 36 months from shipping unless agreed otherwise in
relation to the type of product, the guarantee is limited to replacing a product
found to be faulty. The seller declines all liability in the case of an incorrect
installation or improper use of the products sold.
Implementations of all procedures are established in manual and system, in

which we have been ISO 9001-2008 certified since 2004 & PED 97/23/EC
Disclaimer:
In case of increase in specified pressure or temperature for which the valve has designed or use on wrong applications for which the valve has not
designed. The company will not be responsible & will not accept any claim of replacement.
4
Product Index.
Page No. Index
1 Notes
2 Certificates
3 Introduction
4 Product Index
5 Product Index
6 Mechanical Properties - Valve Selection Guide
7 Working Pressure & Temperatures
Gate Valves
Page No. Items Materials Pressure Ratings Fig No. End Connection
8 Gate Valve Brass, Bronze PN16, PN20, Class 150 A101, A102, A103 Thread End
9 Gate Valve Forged Steel, Stainless Steel Class 150, Class 800 A103, A104 Thread End
10 Gate Valve - Non Rising Stem Cast Iron, Ductile Iron, Cast Steel PN10, PN16 A107, A108, A109 Flange End
11 Gate Valve - Rising Stem OS&Y Cast Iron, Ductile Iron, Cast Steel PN10, PN16 A112, A113, A114 Flange End
12 Gate Valve - Non Rising Stem Cast Iron, Ductile Iron, Cast Steel PN16 A117, A118, A119 Flange End
13 Gate Valve - Rising Stem OS&Y Cast Iron, Ductile Iron, Cast Steel PN16 A122, A123, A124 Flange End
14 Gate Valve - Non Rising Stem Ductile Iron & Cast Steel PN25 A136, A137 Flange End
15 Gate Valve - Rising Stem OS&Y Ductile Iron & Cast Steel PN25 A139, A140 Flange End
16 Gate Valve - Non Rising Stem Ductile Iron & Cast Steel Class 125, Class 150 A127, A128, A129 Flange End
17 Gate Valve - Rising Stem OS&Y Ductile Iron & Cast Steel Class 125, Class 150 A132, A133, A134 Flange End
18 Gate Valve - Non Rising Stem Cast Steel Class 300 A141 Flange End
19 Gate Valve - Rising Stem OS&Y Cast Steel Class 300 A142 Flange End
Globe Valves
20 Globe Valve Bronze, Forged Steel PN20, Class 150, Class 800 B102, B103 Thread End
21 Globe Valve Forged Steel, Stainless Steel PN20, Class 18, Class 800 B104, B105 Thread End
22 Globe Valve Cast Iron, Ductile Iron, Cast Steel PN16 B107, B108, B109 Flange End
23 Globe Valve Cast Iron, Ductile Iron, Cast Steel PN16 B112, B113, B114 Flange End
24 Globe Valve - Bellow Seated Cast Iron, Ductile Iron, Cast Steel PN16 B121, B122, B123 Flange End
25 Globe Valve - Y Type Cast Iron, Ductile Iron, Cast Steel PN16 B125, B126, B127 Flange End
26 Globe Valve Ductile Iron, Cast Steel PN25 B129, B130 Flange End
27 Globe Valve Ductile Iron, Cast Steel PN25 B132, B133 Flange End
28 Globe Valve - Bellow Seated Ductile Iron, Cast Steel PN25 B135, B136 Flange End
29 Globe Valve - Y Type Ductile Iron, Cast Steel PN25 B137, B138 Flange End
30 Globe Valve Cast Steel PN40 B139 Flange End
31 Globe Valve - Bellow Seated Cast Steel PN40 B140 Flange End
32 Globe Valve Cast Iron, Ductile Iron, Cast Steel Class 125, Class 150 B117, B118, B119 Flange End
33 Globe Valve Cast Steel Class 300 B142 Flange End
Check Valves
34 Check Valve - Swing Type Brass, Bronze PN16, PN20, Class 150 C101, C102, C103 Thread End
35 Check Valve - Swing Type Forged Steel, Stainless Steel Class 800, Class 150 C104, C105 Flange End
36 Check Valve - Swing Type Cast Iron, Ductile Iron, Cast Steel Class 125 - Class 150 C107, C108, C109 Flange End
37 Check Valve - Wafer Type Cast Iron, Ductile Iron, Cast Steel PN16 C116, C117, C118 Flange End
38 Check Valve - Lift Type Cast Iron, Ductile Iron, Cast Steel PN16 C120, C121, C122 Flange End
39 Check Valve - Swing Type Ductile Iron, Cast Steel PN25 C126, C127 Flange End
40 Check Valve - Lift Type Ductile Iron, Cast Steel PN25 C129, C130 Flange End
41 Check Valve - Lift Type Cast Steel PN40 C131 Flange End
42 Check Valve - Wafer Type Cast Iron, Ductile Iron, Cast Steel Class 125, Class 150 C112, C113, C114 Flange End
43 Check Valve - Swing Type Cast Steel Class 300 C134 Flange End
5
Product Index.
Strainers
44 Strainer - Y Type Brass, Bronze PN16, PN20 D101, D102 Thread End
45 Strainer - Y Type Cast Iron, Ductile Iron, Cast Steel PN16 D107, D108, D109 Flange End
46 Strainer - Basket type Ductile Iron, Cast Steel PN16 D112, D113, D114 Flange End
47 Strainer - Y Type Ductile Iron, Cast Steel PN25 D116, D117 Flange End
48 Strainer - Basket Type Ductile Iron, Cast Steel PN25, PN40 D119, D120, D121 Flange End
49 Strainer - Y Type Cast Steel Class 300 D123 Flange End
Butterfly Valves
50 Butterfly Valve - Lever Type Cast Iron, Ductile Iron, Cast Steel PN16, Class 125, Class 150 E101, E102, 103 Wafer Type
51 Butterfly Valve - Gear Type Cast Iron, Ductile Iron, Cast Steel PN16, Class 125, Class 150 E105, E106, 107 Wafer Type
Balancing Valves
52 Balancing Valve Bronze, Bronze PN25, PN16 F101, F102 Thread End
53 Balancing Valve Cast Iron, Ductile Iron PN16, PN25 F105, F106, F107 Flange End
71-80 Flow Charts - - - -
Flexible Joints - Rubber & Stainless Steel

54 Rubber Flexible Joints Neoprene, EPDM PN16 G101, G102 Flanged, Threaded
55 Stainless Steel Flexible Joints S.S. 304, S.S. 316 PN16 G103, G104 Flanged, Threaded
Ball Valves
56 Ball Valve Brass, Bronze PN25, PN32, PN40 H101, H102 Thread End
57 Ball Valve S.S. 304 S.S. 304 Class 150, 1000 PSI H103, H104 Threaded, Flanged
58 Ball Valve Cast Iron, Ductile Iron, Cast Steel PN16 H107, H108, 109 Flange End
59 Ball Valve Cast Iron, Ductile Iron, Cast Steel Class 125, Class 150 Flange End
Gas Service Valves

60 Gas Service Valve Cast Iron, Ductile Iron, Cast Steel PN16 K101, K102, K103 Thread End
Auto Air Vents - Water Hammer Arrestor

61 Automatic Air Vents Brass PN16 Z101 Thread End
62 Water Hammer Arrestor Brass PN16 Z102 Thread End
Air Release Valves

63 Air Release Valve - Single Action Cast Iron, Ductile Iron, Cast Steel PN16 L101, L102, L103 Flange End
64 Air Release Valve - Double Action Cast Iron, Ductile Iron, Cast Steel PN16 L104, L105, L106 Flange End
Flanges
Page No. Items Materials Pressure Ratings Fig No. Standards
65 Flange - Raised Face Mild Steel PN10, PN16, PN25, PN40 M101 BS, DIN, EN
66 Flange - Blind Mild Steel PN10, PN16, PN25, PN40 M102 BS, DIN, EN
67 Flange - Welding Neck Mild Steel PN10, PN16, PN25, PN40 M103 BS, DIN, EN
Flange - Slip On Raised Face Mild Steel Class 150 N101 ANSI
68
Flange - Blind Mild Steel Class 150 N102 ANSI
Flange - Slip On Raised Face Mild Steel Class 300 N103 ANSI
69
Flange - Blind Mild Steel Class 300 N104 ANSI
70 Flange - Welding Neck Mild Steel Class 150, Class 300 N105, N106 ANSI
6
Mechanical Properties
Chemical Analysis Cast Iron Ductile Iron Cast Steel

Iron & Residuals % 95.00 94.50 98.10
Carbon % 2.90 - 3.10 3.50 - 3.70 0.30
Silicon % 1.80 - 2.10 2.30 - 2.60 0.60
Manganese % 0.80 - 1.10 0.25 1.00
Microscope Structure
Minimum Mechanical Properties Cast Iron Ductile Iron Cast Steel

Yield Psi 33000 40000 - 50000 36000
Tensile Psi 45000 60000 - 99000 70000
Brunel Hardness (HBW) 145 - 215 130 - 370 185 - 370
Elongation Max 0.3% - 0.8% 7% - 18% 22%
Maximum Service Temperature 150 Degree 400 Degree 400 Degree
Vibration Damping Poor Very Good Very Good
Working Comparison: Area Cast Iron Ductile Iron Cast Steel

Corrosion Picking Level High Low Low
Working Temperature Maximum 230 °c 350 °c 500 °c
Brittleness Breaks Do not Break Do not Break
Flexibility Non Flexible Flexible Flexible
Considerable Working Life “Normal Application” Contact to manufacturer 50% higher than Cast Iron Same as Ductile Iron
Chemical Composition Compliances
Country Origins Short Codes Brass Bronze Grey Cast Iron GG25 Ductile Iron GGG500
Europe EN CW614N CC491K EN-GJL-250 EN-GJS-500
USA ANSI - ASTM C38500 C83600 ASTM A126 Cls B ASTM A536
Germany DIN CuZn39Pb3 G-CuSn5ZnPb 1691GG25 GGG 50
British BS CZ121-Pb3 LG2 BS 1452 250 BS 2789 - 500
Japan Short Codes C38500 C83600 FC250 FCD 500
Chemical Composition Compliances
Country Origins Short Codes Cast Steel A216 Stainless Steel Cr13 Stainless Steel 304 Stainless Steel 316
Europe EN GP40GH x12Cr13 X6CrNi18-10 X6CrNiMo17-13-3
USA ANSI - ASTM ASTM A216 Gr B AISI 410 AISI 304 - A351 CF8 AISI 316 - A351 CF8M
Germany DIN GS-C25N (1.0619+N) 1.4000 1.4301 1.4408
British BS 1504-B 410S21 304S15 316S31
Japan JIS SCPH2 SUS410S SCS13A SCS14A
7
Valves Working Pressure & Temperature Ratings
Brass Bronze Cast Iron

Pressure & Temp Ratings
PN16 PN20 - Class 150 PN16 - 125 Class
PSI PSI PSI

°F °C
1/2” - 4” 1/2” - 4” 1” - 12”
-20 to 150 -29 to 66 200 225 200

200 93 188 210 190
250 121 176 195 175
300 149 153 180 165
350 177 141 165 150
400 204 129 150 140
450 232 107 135 125
PSI
°F °C
14” - 24”
-20 to 150 -29 to 66 150
200 93 135
250 121 125
300 149 110
350 177 100
400 204 -
450 232 -
Valves Working Pressure & Temperature Ratings
Ductile Iron Cast Steel Cast Steel

Pressure & Temp Ratings
PN16 - 150 Class PN16 - 150 Class Class 300
PSI PSI PSI

°F °C
1” - 24” 1” - 24” 1” - 24”
-20 to 150 -29 to 66 250 285 740

200 93 235 260 675
250 121 - - -
300 149 215 230 655
350 177 - - -
400 204 200 200 635
450 232 - - -
500 260 170 170 600
550 288 - - -
600 315 140 140 550
650 343 125 125 535
700 371 - 110 535
750 399 - 95 505
800 426 - 80 410
850 454 - 65 270
900 482 - 50 170
950 510 - 35 105
1000 538 - 20 50
8
Gate Valves also known as Sluice Valves, Isolating Valves & Washout Valves are linear motion valves in which a flat closure element slides into the flow stream to
provide shut-off, they are excellent for use anywhere a shut off valve is needed. Applications: Hot & Cold Water, Oil & Gas, Air, Raw Water
Gate Valve - Brass | PN16

Non Rising Stem (NRS), Screwed Bonnet, Female Threaded End
Design & Compliances: EN 12288-1, BS 5154, MSS SP 80 - Threads to EN 10226-1 comply with BS21
Chemical Composition & Compliances
Refer to Page No. 7
Working Pressure & Temp. Range
Materials Brass (NRS) Bronze (NRS) Bronze (NRS)
Pressure Ratings PN16 PN20 Class 150
Sr. No Parts Fig No. A101 Fig No. A102 Fig No. A103
01 Body Brass CW614N Bronze CC491K Bronze C83600
02 Bonnet Brass CW614N Bronze CC491K Bronze C83600
03 Stem Brass CW614N Bronze CC491K Bronze C83600
04 Wedge Brass CW614N Bronze CC491K Bronze C83600
05 Gland Brass CW614N Bronze CC491K Bronze C83600
06 Gland Packing Non - Asbestos | PTFE Teflon
07 Gasket Non - Asbestos | PTFE Teflon
08 Handwheel Cast Iron EN-GJL-250
Testing Standard - API 598 | EN 12266-1 Shell: 24 Bar | Seat: 18 Bar Shell: 30 Bar | Seat: 22 Bar
Millimeter Dimensions
Sizes 15 20 25 32 40 50 65 80 100
(L) Face to Face 38 44 48 51 58 63 64 75 85
(H) Non Rising Stem 68 78 91 108 125 143 155 183 225
Gate Valve - Bronze | PN20 | Class 150

Non Rising Stem (NRS), Screwed Bonnet, Female Threaded End
“ new “H” brand embossed on valve body, “SCON” name plate on handwheel
Sizes 15 20 25 32 40 50 65 80 100
(L) Face to Face 43 49 54 62 65 76 87 105 124
(H) Non Rising Stem 78 92 103 116 133 156 190 215 258
9
provide shut-off, they are excellent for use anywhere a shut off valve is needed. Applications: Hot & Cold Water, Oil & Gas, Air, Raw Water
Gate Valve - Forged Steel | Class 800

Non Rising Stem, Bolted Bonnet, Threaded End or Socket Weld End
Design & Compliances: API 602, ASME 16.34, BS 5352 Threads to B1.20.1, Socket Weld Ends to ASME B16.11
Materials Forged Steel Stainless Steel
Pressure Ratings Class 800 Class 150
Sr. No Parts Fig No. A104 Fig No. A105
01 Body Forged Steel A105N Stainless Steel 304
02 Bonnet Forged Steel A105N Stainless Steel 304
03 Stem Forged Steel A105N Stainless Steel 304
04 Wedge (Gate) Forged Steel A105N Stainless Steel 304
05 Seat Rings Stainless Steel 304 -
06 Gland Forged Steel A105N -
09 Handwheel Carbon Steel HT 200 Carbon Steel HT 200
10 I. Bolts Carbon Steel ASTM A193 B7 -
Threads to EN 10226-1 comply with BS21, end connections are female threaded.
Testing Standard - API 598 Shell: 200 Bar | Seat: 146 Bar Shell: 30 Bar | Seat: 20 Bar
Sizes 15 20 25 32 40 50 65 80 100
(L) Face to Face 79 92 111 120 120 140 - - -
(H) Non Rising Stem 166 169 193 236 246 283` - - -
Gate Valve - Stainless Steel 304 | PN20 | Class 150

Non Rising Stem, Screwed Bonnet, Female Threaded End
Sizes 15 20 25 32 40 50 65 80 100
(L) Face to Face 55 60 65 75 85 95 115 - -
(H) Non Rising Stem 100 105 117 130 145 170 200 - -
10
provide shut-off, they are excellent for use anywhere a shut off valve is needed. Applications: Hot & Cold Water, Oil & Gas, Air, Steam, Raw Water
Gate Valve - PN10 | PN16

Non Rising Stem (NRS), Inside Screw, Bolted Bonnet, Flange End
Flange outer & drilling to PN10 or PN16 | EN 1092 - BS 4504
Design & Compliances: EN 1171, DIN 3202 F4, EN 558-1 (14)

Compliances of Chemical Compositions
Refer to Page No. 7
Materials Cast Iron Ductile Iron Cast Steel
Pressure Ratings PN10 PN10 PN10
01 Body Cast Iron EN-GJL-250 Ductile Iron EN-GJS-500 Cast Steel GP240GH
02 Bonnet Cast Iron EN-GJL-250 Ductile Iron EN-GJS-500 Cast Steel GP240GH
03 Wedge (Gate) Cast Iron EN-GJL-250 Ductile Iron EN-GJS-500 Cast Steel GP240GH
04 Gland Cast Iron EN-GJL-250 Ductile Iron EN-GJS-500 Cast Steel GP240GH
05 Stem (Trim) Brass CW614N | Bronze CC491K | S.S. Cr13 | S.S. 304 | S.S. 316
06 Seat Rings Brass CW614N | Bronze CC491K | S.S. Cr13 | S.S. 304 | S.S. 316
07 Gland Packing Non - Asbestos | Flexible Graphite
08 Gasket Non - Asbestos | Flexible Graphite
09 Nut Bolts Carbon Steel IS0 8.8 | Galvanized | S.S. 304 ASTM A193 B8
10 Handwheel Cast Iron EN-GJL-250 Ductile Iron EN-GJS-500 Cast Steel GP240GH
Testing Standard - BS 6755 | EN 12266-1 Shell: 24 Bar | Seat: 17.6 Bar
Painting (200-300 Mic) wet blue epoxy paint, corrosion resistant - wet silver paint, high temp & corrosion resistant
 Special Executions (on request with extra charges) - subject to manufacturer acceptance
 Wedge: Brass, Bronze, S.S. 304, S.S. 316
 Gasket, Gland Packing: Wire Woven
 Operation: Extendable Spindle, Chain Sleeve Operation, Gear Operated, Motor Operated
Sizes 40 50 65 80 100 125 150 200 250 300
(L) Face to Face 140 150 170 180 190 200 210 230 250 270
(D) OD - PN10 150 165 185 200 220 250 285 340 395 445
(D) OD - PN16 150 165 185 200 220 250 285 340 405 460
(H) Height 150 170 215 235 250 302 306 397 512 547
(W) Wheel 170 170 170 170 200 200 220 220 300 400
11
Gate Valve - PN10 | PN16

Rising Stem OS&Y, Outside Screw & Yoke, Bolted Bonnet, Flange End
Flange outer & drilling to PN10 or PN16 | EN 1092 - BS 4504
Design & Compliances: EN 1171, DIN 3202 F4, EN 558-1 (14)

Refer to Page No. 7
05 Yoke Cast Iron EN-GJL-250 Ductile Iron EN-GJS-500 Cast Steel GP240GH
 Locking Device: Chain Locking System
Sizes 40 50 65 80 100 125 150 200 250 300
(L) Face to Face 140 150 170 180 190 200 210 230 250 270
(D) OD - PN10 150 165 185 200 220 250 285 340 395 445
(D) OD - PN16 150 165 185 200 220 250 285 340 405 460
(H) Height 245 260 295 366 432 476 553 685 897 1002
(W) Wheel 170 200 200 230 245 245 290 290 400 500
12
Gate Valve - PN16

Flange outer & drilling to PN16 | EN 1092 - BS 4504
Design & Compliances: EN 1171, EN 558-1 (3), BS 5150, BS 5163, AWWA C500-09
Refer to Page No. 7
Sizes 40 50 65 80 100 125 150 200 250 300 350 400 450 500 600 700 800 900
(L) Face to Face 165 178 190 203 229 254 267 292 330 356 381 406 432 457 508 610 660 711
(D) OD 150 165 185 200 220 250 285 340 405 460 520 580 640 715 840 910 1025 1125
(H) Height 223 308 358 420 493 562 633 778 935 1090 1219 1342 1480 1626 1931 2210 - -
(W) Wheel 170 170 170 170 200 200 220 220 300 400 600 600 600 600 800 800 800 800
13
Gate Valve - PN16

Design & Compliances: EN 1171, EN 558-1 (3), BS 5150, BS 5163, AWWA C500-09
Refer to Page No. 7
Sizes 40 50 65 80 100 125 150 200 250 300 350 400 450 500 600 700 800 900
(L) Face to Face 165 178 190 203 229 254 267 292 330 356 381 406 432 457 508 610 660 711
(D) OD 150 165 185 200 220 250 285 340 405 460 520 580 640 715 840 910 1025 1125
(H) Height 263 358 423 500 593 687 783 978 1185 1390 1569 1742 1930 2126 2531 3098 - -
(W) Wheel 170 200 200 230 245 245 290 290 400 500 600 600 600 600 800 800 800 800
14
Gate Valve - PN25

Design & Compliances: EN 1171, EN 558-1 (3), BS 5150, BS 5163

Refer to Page No. 7
Materials Ductile Iron Cast Steel
Pressure Ratings PN25 PN25
01 Body Ductile Iron EN-GJS-500 Cast Steel GP240GH
02 Bonnet Ductile Iron EN-GJS-500 Cast Steel GP240GH
03 Wedge (Gate) Ductile Iron EN-GJS-500 Cast Steel GP240GH
04 Gland Ductile Iron EN-GJS-500 Cast Steel GP240GH
05 Stem (Trim) S.S. Cr13 | S.S. 304 | S.S. 316
06 Seat Rings S.S. Cr13 | S.S. 304 | S.S. 316
10 Handwheel Ductile Iron EN-GJS-500 Cast Steel GP240GH
Testing Standard - BS 6755 | EN 12266-1 Shell: 37.5 Bar | Seat: 27.5 Bar
 Wedge: S.S. 304, S.S. 316
Sizes 40 50 65 80 100 125 150 200 250 300 350 400 450 500 600 700 800 900
(L) Face to Face 165 178 190 203 229 254 267 292 330 356 381 406 432 457 508 610 660 711
(D) OD 150 165 185 200 235 270 300 360 425 485 555 620 670 730 845 960 1085 1185
(H) Height 223 308 358 420 493 562 633 778 935 1090 1219 1342 1480 1626 1931 2210 - -
(W) Wheel 170 170 170 170 200 200 220 220 300 400 600 600 600 600 800 800 800 800
15
Gate Valve - PN25


Refer to Page No. 7
03 Wedge (Gate) Ductile Iron EN-GJS-500 Cast Steel GP240GH
05 Yoke Ductile Iron EN-GJS-500 Cast Steel GP240GH
Sizes 40 50 65 80 100 125 150 200 250 300 350 400 450 500 600 700 800 900
(L) Face to Face 165 178 190 203 229 254 267 292 330 356 381 406 432 457 508 610 660 711
(D) OD 150 165 185 200 235 270 300 360 425 485 555 620 670 730 845 960 1085 1185
(H) Height 263 358 423 500 593 687 783 978 1185 1390 1569 1742 1930 2126 2531 3098 - -
(W) Wheel 170 200 200 230 245 245 290 290 400 500 600 600 600 600 800 800 800 800
16
Gate Valve - Class 125 | Class 150

Flange outer & drilling to Class 150 | ANSI 16.5 & ANSI 16.47
Design & Compliances: API 600, ANSI 16.10, JIS 16K, MSS SP 80, AWWA C500-09
Refer to Page No. 7
Pressure Ratings Class 125 Class 150 Class 150
01 Body Cast Iron ASTM-A126 B Ductile Iron ASTM-A536 Cast Steel ASTM-A216 WCB
02 Bonnet Cast Iron ASTM-A126 B Ductile Iron ASTM-A536 Cast Steel ASTM-A216 WCB
03 Wedge (Gate) Cast Iron ASTM-A126 B Ductile Iron ASTM-A536 Cast Steel ASTM-A216 WCB
04 Gland Cast Iron ASTM-A126 B Ductile Iron ASTM-A536 Cast Steel ASTM-A216 WCB
05 Stem (Trim) Brass C38500 | Bronze C83600 | AISI 410 Cr13 | AISI 304 | AISI 316
06 Seat Rings Brass C38500 | Bronze C83600 | AISI 410 Cr13 | AISI 304 | AISI 316
10 Handwheel Cast Iron ASTM-A126 B Ductile Iron ASTM-A536 Cast Steel ASTM-A216 WCB
 Wedge: Brass, Bronze, AISI 304, AISI 316
Sizes (mm) 40 50 65 80 100 125 150 200 250 300 350 400 450 500 600 700 750 800
Sizes (Inche) 1.5” 2” 2.5” 3” 4” 5” 6” 8” 10” 12” 14” 16” 18” 20” 24” 28” 30” 32”
(L) Face to Face 165 178 190 203 229 254 267 292 330 356 381 406 432 457 508 610 610 660
(D) OD 127 152 178 191 229 254 279 343 406 483 533 597 635 699 813 927 984 1060
(H) Height 223 308 358 420 493 562 633 778 935 1090 1219 1342 1480 1626 1931 2210 - -
(W) Wheel 170 170 170 170 200 200 220 220 300 400 600 600 600 600 800 800 800 800
17
Gate valves also known as Sluice Valves, Isolating Valves & Washout Valves are linear motion valves in which a flat closure element slides into the flow stream to
Gate Valve - Class 125 | Class 150

Design & Compliances: API 600, ANSI 16.10, JIS 16K, MSS SP 80, AWWA C500-09
Refer to Page No. 7
03 Wedge (Gate) Cast Iron ASTM-A126 B Ductile Iron ASTM-A536 Cast Steel ASTM-A216 WCB
05 Yoke Cast Iron ASTM-A126 B Ductile Iron ASTM-A536 Cast Steel ASTM-A216 WCB
 Wedge: Brass, Bronze, AISI 304, AISI 316
Sizes (mm) 40 50 65 80 100 125 150 200 250 300 350 400 450 500 600 700 750 800
Sizes (Inche) 1.5” 2” 2.5” 3” 4” 5” 6” 8” 10” 12” 14” 16” 18” 20” 24” 28” 30” 32”
(L) Face to Face 165 178 190 203 229 254 267 292 330 356 381 406 432 457 508 610 610 660
(D) OD 127 152 178 191 229 254 279 343 406 483 533 597 635 699 813 927 984 1060
(H) Height 263 358 423 500 593 687 783 978 1185 1390 1569 1742 1930 2126 2531 3098 - -
(W) Wheel 170 200 200 230 245 245 290 290 400 500 600 600 600 600 800 800 800 800
18
Gate valves also known as Sluice Valves, Isolating Valves

Valves,&Slide
Washout
ValvesValves
& Washout
are linear
Valves
motion
are linear
valvesmotion
in which
valves
a flatinclosure
which aelement
flat closure
slides
element
into theslides
flow into
stream
the to
flow
stream to
provide shut-off,
providethey
shut-off,
are excellent
they arefor
excellent
use anywhere
for use anywhere
a shut off valve
a shutisoff
needed.
valve isApplications:
needed. Applications:
Hot & ColdHot
Water,
& ColdOilWater,
& Gas,Oil
Air,&Steam,
Gas, Air,
RawSteam,
Water Raw Water
Gate Valve - Class 300

Non Rising Stem (NRS), Bolted Bonnet, Flange End
Design & Compliances: API 600, ANSI 16.10

Refer to Page No. 7
Materials Cast Steel
Pressure Ratings Class 150
Sr. No Parts Fig No. A141
01 Body Cast Steel ASTM-A216 WCB
02 Bonnet Cast Steel ASTM-A216 WCB
03 Wedge (Gate) Cast Steel ASTM-A216 WCB
04 Gland Cast Steel ASTM-A216 WCB
06 Stem (Trim) AISI 410 Cr13 | AISI 304 | AISI 316
07 Seat Rings AISI 410 Cr13 | AISI 304 | AISI 316
10 Nut Bolts | I. Bolts Carbon Steel IS0 8.8 | Galvanized | S.S. 304 ASTM A193 B7
11 Handwheel Cast Steel ASTM-A216 WCB
Testing Standard - API 598 Shell: 75 Bar | Seat: 55 Bar
 Wedge: AISI 304, AISI 316
Sizes (mm) 50 65 80 100 125 150 200 250 300 350 400 450 500 600 700
Sizes (Inche) 2” 2.5” 3” 4” 5” 6” 8” 10” 12” 14” 16” 18” 20” 24” 28”
(L) Face to Face 216 241 282 305 381 403 419 457 502 762 838 914 991 1143 1346
(D) OD 165 191 210 254 279 318 381 445 521 584 648 711 775 914 1035
(H) Height 400 430 500 530 620 730 910 1110 1240 1400 1580 1700 1900 2150 2530
(W) Wheel 200 200 250 250 300 400 500 600 600 700 700 800 800 800 800
19
Gate valves also known as Sluice Valves, Isolating Valves & Washout Valves are linear motion valves in which a flat closure element slides into the flow stream to
Gate Valve - Class 300

Rising Stem, Outside Screw & Yoke, Bolted Bonnet, Flange End
Design & Compliances: API 600, ANSI 16.10

Refer to Page No. 7
Sr. No Parts Fig No. A142
03 Wedge (Gate) Cast Steel ASTM-A216 WCB
05 Yoke Cast Steel ASTM-A216 WCB
06 Stem (Trim) AISI 410 Cr13 | AISI 304 | AISI 316
10 Nut Bolts | I. Bolts Carbon Steel IS0 8.8 | Galvanized | S.S. 304 ASTM A193 B7
 Wedge: AISI 304, AISI 316
Sizes (mm) 50 65 80 100 125 150 200 250 300 350 400 450 500 600 700
Sizes (Inch) 2” 2.5” 3” 4” 5” 6” 8” 10” 12” 14” 16” 18” 20” 24” 28”
(L) Face to Face 216 241 282 305 381 403 419 457 502 762 838 914 991 1143 1346
(D) OD 165 191 210 254 279 318 381 445 521 584 648 711 775 914 1035
(H) Height 400 430 500 530 620 730 910 1110 1240 1400 1580 1700 1900 2150 2530
(W) Wheel 200 200 250 250 300 400 500 600 600 700 700 800 800 800 800
20
Globe Valves also known as Regulating Valves are linear motion valves, they are widely used in industry to regulate fluid flow in both on/off and throttling service,
the location of the valve disk in relation to the valve seat allows or restricts flow. Applications: Hot & Cold Water, Oil & Gas, Air, Steam, Raw Water
Globe Valve - Bronze | PN20

Screwed Bonnet, Female Threaded End
Design & Compliances: BS 5154, MSS SP 80, Threads to EN 10226-1 comply with BS21
Refer to Page No. 7
Materials Bronze Bronze
Pressure Ratings PN20 Class 150
Sr. No Parts Fig No. B102 Fig No. B103
01 Body Bronze CC491K Bronze C83600
02 Bonnet Bronze CC491K Bronze C83600
03 Stem Bronze CC491K Bronze C83600
04 Disc Bronze CC491K Bronze C83600
05 Seat Rings Bronze CC491K Bronze C83600
06 Gland Bronze CC491K Bronze C83600
09 Handwheel Cast Iron EN-GJL-250
Testing Standard - API 598 | EN 12266-1 Shell: 30 Bar | Seat: 20 Bar
new “H” brand embossed on valve body, “SCON” name plate on handwheel
Sizes 15 20 25 32 40 50
(L) Face to Face 52 63 76 84 98 116
(H) Rising Stem OS&Y 70 82 92 108 120 140
Globe Valve - Bronze | Class 150

Sizes 15 20 25 32 40 50
(L) Face to Face 54 65 78 87 101 119
(H) Non Rising Stem 72 84 94 111 123 143
21
Globe Valve - Forged Steel | Class 800

Bolted Bonnet, Female Threaded End or Socket Weld End
Design & Compliances: ASME 16.34, BS 5352 Threads to B1.20.1, Socket Weld Ends to ASME B16.11
Refer to Page No. 7
Materials Forged Steel Stainless Steel 304
Pressure Ratings Class 800 Class 150
01 Body Forged Steel A105 Stainless Steel 304
02 Bonnet Forged Steel A105 Stainless Steel 304
03 Stem Stainless Steel 304 Stainless Steel 304
04 Disc Forged Steel A105 Stainless Steel 304
05 Seat Rings Stainless Steel 304 Stainless Steel 304
06 Gland Forged Steel A105 -
09 Handwheel Forged Steel A105 Cast Iron EN-GJL-250
10 I. Bolts Carbon Steel ASTM A193 B7 -
Testing Standard - API 598 | EN 12266-1 Shell: 200 Bar | Seat: 146 Bar Shell: 30 Bar | Seat: 20 Bar
Sizes 15 20 25 32 40 50
(L) Face to Face 79 92 111 120 152 172
(H) Rising Stem OS&Y 158 192 252 252 289 330
Globe Valve - Stainless Steel 304 | PN20 | Class 150

Sizes 15 20 25 32 40 50
(L) Face to Face 65 80 90 105 120 140
(H) Non Rising Stem 85 95 110 120 135 150
22
Globe Valves - PN16

Rising Handwheel, Bolted Bonnet, Flange End
Design & Compliances: EN 13789, EN 558-1 (1), BS 5152, DIN 3352, DIN 3202 (1)
Refer to Page No. 7
Sr. No Parts Fig No. B107 Fig No. A108 Fig No. A109
03 Disc Cast Iron EN-GJL-250 Ductile Iron EN-GJS-500 Cast Steel GP240GH
06 Stem (Trim) Bronze CC491K | S.S. Cr13 | S.S. 304 | S.S. 316
07 Seat Rings Bronze CC491K | S.S. Cr13 | S.S. 304 | S.S. 316
Testing Standard - BS 6755 | EN 12266-1 Shell: 24 Bar | Seat: 18 Bar
 Disc: Brass, Bronze, S.S. 304, S.S. 316
 Gasket, Gland Packing: Spiral Wound, Wire Woven
 Operation: Chain Sleeve Operated, Gear Operated
Sizes 15 20 25 32 40 50 65 80 100 125 150 200 250 300
(L) Face to Face 130 150 160 180 200 230 290 310 350 400 480 600 730 850
(D) OD 95 105 115 140 150 165 185 200 220 250 285 340 405 460
(H) Height 200 218 236 260 284 302 340 399 423 501 555 665 795 897
(W) Wheel 110 110 110 160 160 160 195 195 270 270 315 405 405 405
23
Globe Valves - PN16

Design & Compliances: EN 13789, EN 558 (10), BS 5153

Refer to Page No. 7
Sr. No Parts Fig No. B112 Fig No. B113 Fig No. B114
Sizes 40 50 65 80 100 125 150 200 250 300 350 400 450 500 600 700
(L) Face to Face 165 203 216 241 292 330 356 495 622 699 787 914 978 978 1295 -
(D) OD 150 165 185 200 220 250 285 340 405 460 520 580 640 715 840 910
(H) Height 284 302 340 399 423 501 555 665 795 897 1155 1235 1347 1550 - -
(W) Wheel 160 160 195 195 270 270 315 405 405 405 405 510 510 600 600 800
24
Globe Valve - Bellow Seated | PN16

Refer to Page No. 7
06 Bellow S.S. 304 | S.S. 316
 Disc: S.S. 304, S.S. 316
 Operation: Chain Sleeve Operated
Sizes 15 20 25 32 40 50 65 80 100 125 150 200 250 300
(L) Face to Face 130 150 160 180 200 230 290 310 350 400 480 600 730 850
(D) OD 95 105 115 140 150 165 185 200 220 250 285 340 405 460
(H) Height 200 218 236 260 284 302 340 399 423 501 555 665 795 897
(W) Wheel 110 110 110 160 160 160 195 195 270 270 315 405 405 405
25
Globe Valve - Y Type | PN16

Design & Compliances: EN 13789, EN 558-1 (1), BS 7350, BS 5152, DIN 3352, DIN 3202 (1)
Refer to Page No. 7
Sizes 40 50 65 80 100 125 150 200 250 300 350 400 450 500 600
(L) Face to Face 165 203 216 241 292 330 356 495 622 699 787 914 978 978 1295
(D) OD 150 165 185 200 220 250 285 340 405 460 520 580 640 715 840
(H) Height 305 340 380 450 500 570 650 840 950 1100 1250 1498 1651 1845 2140
(W) Wheel 160 160 195 195 270 270 315 405 405 405 405 510 510 600 600
26
Globe Valve - PN25

Refer to Page No. 7
03 Disc Ductile Iron EN-GJS-500 Cast Steel GP240GH
 Disc: S.S. 304, S.S. 316
Sizes 15 20 25 32 40 50 65 80 100 125 150 200 250 300
(L) Face to Face 130 150 160 180 200 230 290 310 350 400 480 600 730 850
(D) OD 95 105 115 140 150 165 185 200 235 270 300 340 425 485
(H) Height 200 218 236 260 284 302 340 399 423 501 555 665 795 897
(W) Wheel 110 110 110 160 160 160 195 195 270 270 315 405 405 405
27
]=
Globe Valve - PN25

Design & Compliances: EN 13789, EN 558 (10), BS 5153

Refer to Page No. 7
Testing Standard - BS 6755 | EN 12266-1 Shell:24 Bar | Seat: 18 Bar
 Disc: S.S. 304, S.S. 316
Sizes 40 50 65 80 100 125 150 200 250 300 350 400 450 500 600 700
(L) Face to Face 165 203 216 241 292 330 356 495 622 699 787 914 978 978 1295 -
(D) OD 150 165 185 200 235 270 300 340 425 485 555 620 670 730 845 960
(H) Height 284 302 340 399 423 501 555 665 795 897 1155 1235 1347 1550 - -
(W) Wheel 160 160 195 195 270 270 315 405 405 405 405 510 510 600 600 800
28

Refer to Page No. 7
Sr. No Parts Fig No. A135 Fig No. B136
06 Bellow S.S. 304 | S.S. 316
 Disc: S.S. 304, S.S. 316
Sizes 15 20 25 32 40 50 65 80 100 125 150 200 250 300
(L) Face to Face 130 150 160 180 200 230 290 310 350 400 480 600 730 850
(D) OD 95 105 115 140 150 165 185 200 235 270 300 340 425 485
(H) Height 200 218 236 260 284 302 340 399 423 501 555 665 795 897
(W) Wheel 110 110 110 160 160 160 195 195 270 270 315 405 405 405
29
Globe Valve - Y Type | PN25

Design & Compliances: EN 13789, EN 558-1 (1), BS 7350, BS 5152, DIN 3352, DIN 3202 (1)
Refer to Page No. 7
 Disc: S.S. 304, S.S. 316
Sizes 40 50 65 80 100 125 150 200 250 300 350 400 450 500 600
(L) Face to Face 165 203 216 241 292 330 356 495 622 699 787 914 978 978 1295
(D) OD 150 165 185 200 235 270 300 340 425 485 555 620 670 730 845
(H) Height 305 340 380 450 500 570 650 840 950 1100 1250 1498 1651 1845 2140
(W) Wheel 160 160 195 195 270 270 315 405 405 405 405 510 510 600 600
30
Globe Valve - PN40

Refer to Page No. 7
Pressure Ratings PN40
Sr. No Parts Fig No. B139
01 Body Cast Steel GP240GH
02 Bonnet Cast Steel GP240GH
03 Disc Cast Steel GP240GH
04 Yoke Cast Steel GP240GH
05 Gland Cast Steel GP240GH
11 Handwheel Cast Steel GP240GH
 Disc: S.S. 304, S.S. 316
Sizes 15 20 25 32 40 50 65 80 100 125 150 200 250 300
(L) Face to Face 130 150 160 180 200 230 290 310 350 400 480 600 730 850
(D) OD 95 105 115 140 150 165 185 200 235 270 300 375 450 515
(H) Height 200 218 236 260 284 302 340 399 423 501 555 665 795 897
(W) Wheel 110 110 110 160 160 160 195 195 270 270 315 405 405 405
31

Refer to Page No. 7
02 Bonnet Cast Steel GP240GH
04 Yoke Cast Steel GP240GH
05 Gland Cast Steel GP240GH
06 Bellow S.S. 304 | S.S. 316
12 Handwheel Cast Steel GP240GH
 Disc: S.S. 304, S.S. 316
Sizes 15 20 25 32 40 50 65 80 100 125 150 200 250 300
(L) Face to Face 130 150 160 180 200 230 290 310 350 400 480 600 730 850
(D) OD 95 105 115 140 150 165 185 200 235 270 300 375 450 515
(H) Height 200 218 236 260 284 302 340 399 423 501 555 665 795 897
(W) Wheel 110 110 110 160 160 160 195 195 270 270 315 405 405 405
32
Globe Valve - Class 125 | Class 150

Flange outer & drilling to Class 150 | ANSI 16.5 - ANSI 16.47
Design & Compliances: ANSI 16.34, ANSI 16.10, MSS SP 85, JIS 16K wall thickness to API 600
Refer to Page No. 7
03 Disc Cast Iron ASTM-A126 B Ductile Iron ASTM-A536 Cast Steel ASTM-A216 WCB
04 Yoke Cast Iron ASTM-A126 B Ductile Iron ASTM-A536 Cast Steel ASTM-A216 WCB
 Disc: Brass, Bronze, AISI 304, AISI 316
Sizes (mm) 40 50 65 80 100 125 150 200 250 300 350 400 450 500 600 700
Sizes (Inch) 1.5” 2” 2.5” 3” 4” 5” 6” 8” 10” 12” 14” 16” 18” 20” 24” 28”
(L) Face to Face 165 203 216 241 292 330 356 495 622 699 787 914 978 978 1295 -
(D) OD 127 152 178 191 229 254 279 343 406 483 533 597 635 698 813 927
(H) Height 284 302 340 399 423 501 555 665 795 897 1155 1235 1347 1550 - -
(W) Wheel 160 160 195 195 270 270 315 405 405 405 405 510 510 600 600 800
33
Globe Valve - Class 300

Flange outer & drilling to Class 300 | ANSI 16.5
Design & Compliances: ANSI 16.34, BS 1873 wall thickness to API 600
Refer to Page No. 7
03 Disc Cast Steel ASTM-A216 WCB
04 Yoke Cast Steel ASTM-A216 WCB
06 Stem (Trim) Brass C38500 | Bronze C83600 | AISI 410 Cr13 | 3 | AISI 304 | AISI 316
07 Seat Rings Brass C38500 | Bronze C83600 | AISI 410 Cr13 | 3 | AISI 304 | AISI 316
 Disc: AISI 304, AISI 316
Sizes (mm) 40 50 65 80 100 125 150 200 250 300 350 400 450 500
Sizes (Inch) 1.5” 2” 2.5” 3” 4” 5” 6” 8” 10” 12” 14” 16” 18” 20”
(L) Face to Face 267 292 318 356 400 445 533 622 711 838 864 - - -
(D) OD 165 191 210 254 279 318 381 445 521 584 648 711 775 914
(H) Height 320 350 380 430 480 560 680 750 860 910 1240 - - -
(W) Wheel 200 225 225 300 300 400 500 600 600 800 800 - - -
34
Non-Return Valves also known as Check Valves or Reflex Valves, permit media to flow in only one direction, preventing process flow from reversing, fluid flow in the
desired opens the valves they are classified as one-way directional valves. Applications: Hot & Cold Water, Oil & Gas, Air, Steam, Raw Water
Non Return Valve - Check Valve | PN16

Brass, Swing Type, Screwed Bonnet, Female Threaded End
Design & Compliances: BS 5154, MSS SP 80, Threads to EN 10226-1 comply with BS21
Composition Compliances
Refer to Page No. 7
Working Pressure & Temp.
Materials Brass Bronze Bronze
Sr. No Parts Fig No. C101 Fig No. C102 Fig No. C103
02 Bonnet (Top Plate) Brass CW614N Bronze CC491K Bronze C83600
03 Disc Brass CW614N Bronze CC491K Bronze C83600
04 Disc Hanger Brass CW614N Bronze CC491K Bronze C83600
05 Hinge Brass CW614N Bronze CC491K Bronze C83600
Testing Standards - EN 12266-1 | API 598 Shell: 24 Bar | Seat: 18 Bar Shell: 30 Bar | Seat: 22 Bar
Sizes 15 20 25 32 40 50 65 80 100
(L) Face to Face 47 53 63 70 88 97 120 135 162
(H) Height 51 58 68 78 98 109 130 145 180
Non Return Valve - Check Valve | PN20 | Class 150

Bronze, Swing Type, Screwed Bonnet, Female Threaded End
new “H” brand embossed on valve body

Sizes 15 20 25 32 40 50 65 80 100
(L) Face to Face 49 55 65 72 91 100 123 138 165
(H) Height 52 59 70 80 100 112 133 148 183
35
Non Return Valve - Check Valve | Class 800

Forged Steel, Swing Type, Bolted Bonnet
Socket Weld End or Female Threaded End
Design & Compliances: ASME 16.34, BS 5352 Threads to B1.20.1, Socket Weld Ends to ASME B16.11
Materials Forged Steel Stainless Steel
Pressure Ratings Class 800 PN20 - Class 150
01 Body Forged Steel A105 Stainless Steel 304
02 Bonnet (Top Plate) Forged Steel A105 Stainless Steel 304
03 Disc Forged Steel A105 Stainless Steel 304
04 Seat Rings AISI 304 -
05 Disc Hanger Forged Steel A105 AISI 304
06 Hinge AISI 304 AISI 304
08 Nut Bolts Carbon Steel -
Testing Standards - API 598 Shell: 200 Bar | Seat: 146 Bar Shell: 30 Bar | Seat: 20 Bar
Sizes 15 20 25 32 40 50
(L) Face to Face 90 110 127 150 180 210
(H) Height 60 78 88 92 108 145
Non Return Valve - Check Valve | PN20 | Class 150

S.S. 304, Swing Type, Screwed Bonnet, Female Threaded End
Sizes 15 20 25 32 40 50
(L) Face to Face 65 80 89 105 120 139
(H) Height 43 50 60 66 75 80
36

Swing Type, Bolted Bonnet, Flange End

Refer to Page No. 7
02 Bonnet (Top Plate) Cast Iron EN-GJL-250 Ductile Iron EN-GJS-500 Cast Steel GP240GH
05 Hinge Pin Cast Steel GP240GH | S.S. 304
06 Disc Hanger Cast Steel GP240GH | S.S. Cr13 | S.S. 304 | S.S. 316
 Gasket: Spiral Wound, Wire Woven
 Operation: Weight Closure
 Eye Bolt at Top Flange
Sizes 40 50 65 80 100 125 150 200 250 300 350 400 450 500 600 700
(L) Face to Face 165 203 216 241 292 330 356 495 622 699 787 914 978 978 1295 1448
(D) OD 150 165 185 200 220 250 285 340 405 460 520 580 640 715 840 910
(H) Height 98 114 140 150 160 189 199 245 289 320 362 385 455 495 570 690
37

Piston Type - Lift Type, Spring Loaded, Bolted Bonnet, Flange End
Refer to Page No. 7
05 Spring S.S. 304 | S.S. 316
 Disc: Bronze, S.S. 304, S.S. 316
Sizes 15 20 25 32 40 50 65 80 100 125 150 200 250 300
(L) Face to Face 130 150 160 180 200 230 290 310 350 400 480 600 730 850
(D) OD 95 105 115 140 150 165 185 200 220 250 285 340 405 460
(H) Height 100 110 120 150 165 180 210 225 240 265 320 365 460 520
38

Wafer Type, mounting between PN16 or Class 150 Flanges
Suitable Flange Connections are EN 1092 - BS 4504 | ANSI 16.5
Design & Compliances: EN 558-1 (16), BS 5155, API 594, ISO 5752, DIN 3202
Refer to Page No. 7
02 Seat Ring EPDM | NBR
03 Disc (Dual Plate) Ductile Iron EN-GJS-500 | Bronze CC491K | S.S. 304 | S.S. 316
04 Shaft S.S. Cr13 | S.S. 304 | S.S. 316
05 Spring S.S. 304 | S.S. 316
06 O’ Ring Brass CW614N | Bronze CC491K | S.S. 304 | EPDM | PTFE Teflon
 Operation: Single Plate
Sizes 40 50 65 80 100 125 150 200 250 300 350 400 450 500 600
(L) Face to Face 43 46 64 64 70 76 89 114 114 127 140 152 152 165 178
(D) OD 127 152 180 191 228 256 279 344 406 485 535 592 632 - -
(H) Height 164 203 216 241 292 330 356 495 622 699 785 853 983 - -
39


Refer to Page No. 7
Sr. No Parts Fig No. C126 Fig No. C127
02 Bonnet (Top Plate) Ductile Iron EN-GJS-500 Cast Steel GP240GH
05 Hinge Pin Carbon Steel | Stainless Steel 304
06 Disc Hanger Bronze CC491K | S.S. Cr13 | S.S. 304 | S.S. 316
Sizes 40 50 65 80 100 125 150 200 250 300 350 400 450 500 600 700
(L) Face to Face 165 203 216 241 292 330 356 495 622 699 787 914 978 978 1295 1448
(D) OD 150 165 185 200 235 270 300 360 425 485 555 620 670 730 845 960
(H) Height 98 114 140 150 160 189 199 245 289 320 362 385 455 495 570 690
40

Refer to Page No. 7
Sr. No Parts Fig No. C129 Fig No. C130
05 Spring S.S. 304 | S.S. 316
 Disc: Bronze, S.S. 304, S.S. 316
Sizes 15 20 25 32 40 50 65 80 100 125 150 200 250 300
(L) Face to Face 130 150 160 180 200 230 290 310 350 400 480 600 730 850
(D) OD 95 105 115 140 150 165 185 200 235 270 300 360 425 485
(H) Height 100 110 120 150 165 180 210 225 240 265 320 365 460 520
41

Refer to Page No. 7
Sr. No Parts Fig No. C131
02 Bonnet (Top Plate) Cast Steel GP240GH
05 Spring S.S. 304 | S.S. 316
 Disc: S.S. 304, S.S. 316
Sizes 15 20 25 32 40 50 65 80 100 125 150 200 250 300
(L) Face to Face 130 150 160 180 200 230 290 310 350 400 480 600 730 850
(D) OD 95 105 115 140 150 165 185 200 235 270 300 375 450 515
(H) Height 100 110 120 150 165 180 210 225 240 265 320 365 460 520
42
Non Return Valve - Check Valve | Class 125 | Class 150

Design & Compliances: ANSI 594, ASME 16.34, ANSI 16.10, JIS 16K, MSS SP 71, AWWA C508
Refer to Page No. 7
02 Bonnet (Top Plate) Cast Iron ASTM-A126 B Ductile Iron ASTM-A536 Cast Steel ASTM-A216 WCB
03 Disc Cast Iron ASTM-A126 B Ductile Iron ASTM-A536 Cast Steel ASTM-A216 WCB
04 Seat Rings Brass C38500 | Bronze C83600 | AISI 410 Cr13 | AISI 304 | AISI. 316
05 Hinge Pin Carbon Steel | AISI 304
06 Disc Hanger AISI 410 Cr13 | AISI 304 | AISI 316
08 Nut Bolts Carbon Steel IS0 8.8 | Galvanized | AISI 304 ASTM A193 B8
 Disc: Brass, Bronze, AISI 304, AISI 316
Sizes (mm) 40 50 65 80 100 125 150 200 250 300 350 400 450 500 600 700
Sizes (Inch) 1.5” 2” 2.5” 3” 4” 5” 6” 8” 10” 12” 14” 16” 18” 20” 24” 28”
(L) Face to Face 165 203 216 241 292 330 356 495 622 699 787 914 978 978 1295 1448
(D) OD 127 152 178 191 229 254 279 343 406 483 533 597 635 698 813 927
(H) Height 98 114 140 150 160 189 199 245 289 320 362 385 455 495 570 690
43
Non Return Valve - Check Valve | Class 300

Design & Compliances: ANSI 594, ASME 16.34, ANSI 16.10

Refer to Page No. 7
Sr. No Parts Fig No. C134
02 Bonnet (Top Plate) Cast Steel ASTM-A216 WCB
03 Disc Cast Steel ASTM-A216 WCB
05 Hinge Pin Carbon Steel | AISI 304
06 Disc Hanger AISI 410 Cr13 | AISI 304 | AISI 316
 Disc: Brass, Bronze, S.S. 304, S.S. 316 Installations
Sizes (mm) 40 50 65 80 100 125 150 200 250 300 350 400 450 500 600 700
Sizes (Inch) 1.5” 2” 2.5” 3” 4” 5” 6” 8” 10” 12” 14” 16” 18” 20” 24” 28”
(L) Face to Face 165 203 216 241 292 330 356 495 622 711 838 864 978 1036 1346 1499
(D) OD 156 165 191 210 254 279 318 381 445 521 584 648 711 775 914 1035
(H) Height 150 180 200 225 270 300 355 390 445 495 530 610 660 750 890 1030
44
Strainers protect the fluid handling against the damage that can occur to valves & other equipment when foreign matter such as dirt, scale or welding particles
travel through the pipeline, can improve the clearance in media & prolong the life of valves. Applications: Hot & Cold Water, Oil & Gas, Air, Steam, Raw Water
Strainer - Brass | PN16

Y Type, Screwed Bonnet, Female Threaded End
Threads to EN 10226-1 comply with BS21

Refer to Page No. 7
Materials Brass Bronze Bronze
Sr. No Parts Fig No. D101 Fig No. D102 Fig No. D103
02 Bonnet (Top Plate) Brass CW614N Bronze CC491K Bronze C83600
03 Perforated Mesh Brass CW614N Bronze CC491K Bronze C83600
Testing Standard - EN 12266-1 | API 598 Shell: 24 Bar | Seat: 18 Bar Shell: 30 Bar | Seat: 22 Bar
Sizes 15 20 25 32 40 50 65 80 100
(L) Face to Face 56 67 74 96 104 125 146 170 210
(H) Height 40 46 50 67 74 90 107 123 152
Strainer - Bronze | PN20

Y Type, Screwed Bonnet, Female Threaded End
new “H” brand embossed on valve body

Sizes 15 20 25 32 40 50 65 80 100
(L) Face to Face 58 70 88 96 107 126 230 260 330
(H) Height 33 41 49 56 62 80 110 142 175
45
Strainer - PN16
Y Type, Bolted Bonnet, Flange End
Design & Compliances: EN 13789, BS 5152 Y Type, BS 7350, EN 558-1 (1), DIN 3352
Refer to Page No. 7
03 Perforated Mesh S.S. 304 | S.S.316
 Drain Plug at Top Plate
 Flange PCD to Class 150 | ANSI 16.5
 Mesh Size & Holes as per requirement
Sizes 40 50 65 80 100 125 150 200 250 300 350 400 450 500 600
(L) Face to Face 200 230 290 310 350 400 480 600 730 850 980 1100 1200 1250 1450
(D) OD 150 165 185 200 220 250 285 340 405 460 520 580 640 715 840
(H) Height 60 80 90 110 150 165 190 240 250 325 390 450 565 600 640
46
Strainer - PN16
Basket Type, Bolted Bonnet, Flange End
Design & Compliances: EN 13789, BS 5152 Y Type, EN 558-1 (1), DIN 3352
Refer to Page No. 7
Sizes 15 20 25 32 40 50 65 80 100 125 150 200 250 300
(L) Face to Face 130 150 160 180 200 230 290 310 350 400 480 600 730 850
(D) OD 95 105 115 140 150 165 185 200 220 250 285 340 405 460
(H) Height 100 110 120 150 165 180 210 225 240 265 320 365 460 520
47
Strainer - PN25
Refer to Page No. 7
Sr. No Parts Fig No. D116 Fig No. D117
Sizes 40 50 65 80 100 125 150 200 250 300 350 400 450 500 600
(L) Face to Face 200 230 290 310 350 400 480 600 730 850 980 1100 1200 1250 1450
(D) OD 150 165 185 200 235 270 300 360 425 485 555 620 670 730 845
(H) Height 60 80 90 110 150 165 190 240 250 325 390 450 565 600 640
48
Strainer - PN25 | PN40

Basket Type, Bolted Bonnet, Flange End
Flange outer & drilling to PN25 & PN40 | EN 1092 - BS 4504
Refer to Page No. 7
Materials Ductile Iron Cast Steel Cast Steel
01 Body Ductile Iron EN-GJS-500 Cast Steel GP240GH Cast Steel GP240GH
02 Bonnet (Top Plate) Ductile Iron EN-GJS-500 Cast Steel GP240GH Cast Steel GP240GH
Testing Standard - BS 6755 | EN 12266-1 Shell: 37.5 Bar | Seat: 27.5 Bar Shell: 60 Bar | Seat: 44 Bar
Sizes 15 20 25 32 40 50 65 80 100 125 150 200 250 300
(L) Face to Face 130 150 160 180 200 230 290 310 350 400 480 600 730 850
(D) OD - PN25 95 105 115 140 150 165 185 200 235 270 300 360 425 485
(D) OD - PN40 95 105 115 140 150 165 185 200 235 270 300 375 450 515
(H) Height 100 110 120 150 165 180 210 225 240 265 320 365 460 520
49
Strainer - Class 300

Flange outer & drilling to ANSI 16.5 - Class 300
Design & Compliances: ANSI 16.10

Refer to Page No. 7
Sr. No Parts Fig No. D123
02 Bonnet (Top Plate) Cast Steel ASTM-A216 WCB
 Mesh Size & Holes as per Requirement
Sizes (mm) 40 50 65 80 100 125 150 200 250 300 350 400 450 500 600
Sizes (Inch) 1.5” 2” 2.5” 3” 4” 5” 6” 8” 10” 12” 14” 16” 18” 20” 24”
(L) Face to Face 267 292 318 356 400 445 533 622 711 838 864 978 1016 1346 267
(D) OD 156 165 191 210 254 279 318 381 445 521 584 648 711 775 914
(H) Height 135 145 190 223 245 300 330 365 570 740 - - - - -
50
Butterfly valves are quick opening valves, The are normally used as throttling valves to control flow, it control the flow of gas or liquid by means of a disk, which
permits flow in only one direction, these valves offer a rotary stem movement of 90 degrees. Applications: Hot & Cold Water, Oil & Gas, Air, Steam, Raw Water
Applications: Hot & Cold Water, Oil & Gas, Air, Steam
Butterfly Valve - PN16 | Class 150

Wafer Type, Lever Operated
Design & Compliances: EN 558-1 (16), BS 5155, API 609, API 594, ISO 5752, DIN 3202, JIS B 2032, AWWA C504, MSS SP 67
Refer to Page No. 7
Pressure Ratings PN16 - Class 125 PN16 - Class 150 PN16 - Class 150
Sr. No Parts Fig No. E101 Fig No. E102 Fig No. E103
02 Seat Ring (Liner) EPDM
04 Stem (Shaft) S.S. Cr13 | S.S. 304 | S.S. 316
05 Lever Cast Iron EN-GJL-250 | Ductile Iron EN-GJS-500
06 Stem O Ring EPDM | PTFE Teflon
 Electric Actuator: Single Phase, Three Phase, IP67 Enclosure
 PTFE coated disc
 Sizes upto 60” (DN1500) to be quoted against request
Sizes 40 50 65 80 100 125 150 200 250 300 350 400 450 500 600
(L) Width 42 42 43 46 51 54 55 60 65 75 78 86 105 130 152
(H1) Height 1 67 67 74 94 111 129 141 173 206 235 267 298 318 349 410
(H2) Height 2 142 142 152 162 181 191 205 239 269 306 368 400 422 479 562
(R) Lever 280 280 280 280 280 280 280 384 384 537 - - - - -
51
Butterfly valves are quick opening valves, The are normally used as throttling valves to control flow, it control the flow of gas or liquid by means of a disk, which
permits flow in only one direction, these valves offer a rotary stem movement of 90 degrees. Applications: Hot & Cold Water, Oil & Gas, Air, Steam, Raw Water
Applications: Hot & Cold Water, Oil & Gas, Air, Steam
Butterfly Valve - PN16 | Class 150

Wafer Type, Gear Operated
Design & Compliances: EN 558-1 (16), BS 5155, API 609, API 594, ISO 5752, DIN 3202, JIS B 2032, AWWA C504, MSS SP 67
Refer to Page No. 7
Pressure Ratings PN16 - Class 125 PN16 - Class 150 PN16 - Class 150
Sr. No Parts Fig No. E105 Fig No. E106 Fig No. E107
02 Seat Ring (Liner) EPDM
04 Stem (Shaft) S.S. Cr13 | S.S. 304 | S.S. 316
05 Lever Cast Iron EN-GJL-250 | Ductile Iron EN-GJS-500
06 Stem O Ring EPDM | PTFE Teflon
 Electric Actuator: Single Phase, Three Phase, IP67 Enclosure
 PTFE coated disc
 Sizes upto 60” (DN1500) to be quoted against request
Sizes 40 50 65 80 100 125 150 200 250 300 350 400 450 500 600
(L) Width 42 42 43 46 51 54 55 60 65 75 78 86 105 130 152
(H1) Height 1 67 67 74 94 111 129 141 173 206 235 267 298 318 349 410
(H2) Height 2 142 142 152 162 181 191 205 239 269 306 368 400 422 479 562
(R) Gear - - - - - - - - - - - - - - -
52
Balancing Valves also known as commissioning valve, combination flow regulating valve, double regulating or as circuit setter are installed in the pipe work of hot
water, central heating cooling systems and serve to achieve a hydraulic balance between the various circuits of the systems. Applications: Hot & Cold Water
Balancing Valve - Hot Brass | PN16

Static Type, Y Pattern, Female Thraeded End with 2 Test Ports
These valves have memory stop & position lock feature, Threads to EN 10226-1 comply with BS21
Refer to Page No. 07
Flow Curves (Charts) Refer to Page No. 71-80
Materials Brass Bronze
Sr. No Parts Fig No. F101 Fig No. F102
01 Body Brass CW614N Bronze CC491K
02 Bonnet Brass CW614N Bronze CC491K
03 Stem Brass CW614N Bronze CC491K
04 Disc Brass CW614N Bronze CC491K
06 Indicator PVC - ABS
07 Handwheel PVC - ABS
Testing Standard - BS 6755 | EN 12266-1 Shell: 24 Bar | Seat: 18 Bar Shell: 30 Bar | Seat: 20 Bar
Sizes 15 20 25 32 40 50
(L) Face to Face 77 82 97 115 129 152
(H) Height 104 104 017 114 120 132
Balancing Valve - Bronze | PN25

Static Type, Y Pattern, Female Thraeded End with 2 Test Ports
Sizes 15 20 25 32 40 50
(L) Face to Face 87 96 100 114 125 146
(H) Height 105 106 127 128 143 144
53
Balancing Valves also known as commissioning valve, combination flow regulating valve, double regulating or as circuit setter are installed in the pipe work of hot
water, central heating cooling systems and serve to achieve a hydraulic balance between the various circuits of the systems. Applications: Hot & Cold Water
Balancing Valve - PN16 | PN25

Static Type, Y Pattern, Bolten Bonnet, Flange End
Flange outer & drilling to PN16 - PN25 | EN 1092 - BS 4504
Design & Compliances: EN 13789, BS 5152 Y Type, BS 7350, DIN 3352

Refer to Page No. 7
Flow Curves (Charts) Refer to Page No. 71-80
Materials Cast Iron Ductile Iron Ductile Iron
Sr. No Parts Fig No. F105 Fig No. F106 Fig No. F107
01 Body Cast Iron EN-GJL-250 Ductile Iron EN-GJS-500 Ductile Iron EN-GJS-500
02 Bonnet Cast Iron EN-GJL-250 Ductile Iron EN-GJS-500 Ductile Iron EN-GJS-500
03 Disc Cast Iron EN-GJL-250 Ductile Iron EN-GJS-500 Ductile Iron EN-GJS-500
04 Disc Seat Ring PTFE Teflon
05 Stem Bronze CC491K
06 Bearing Bush Bronze CC491K
07 O’ Ring EPDM - PTFE Teflon
08 Indicator PVC - ABS
11 Handwheel Cast Iron EN-GJL-250 Ductile Iron EN-GJS-500 Ductile Iron EN-GJS-500
Painting (200-300 Mic) wet blue epoxy paint, corrosion resistant - wet blue urethene paint, corrosion resistant
 Disc: Bronze
 O’ Rings: Bronze
Sizes 65 80 100 125 150 200 250 300
(L) Face to Face 290 310 350 400 480 600 730 850
(H) Height 250 300 330 360 405 580 640 710
(D) Flange OD - PN16 185 200 220 250 285 340 405 460
(D) Flange OD - PN25 185 200 235 270 300 360 425 485
54
Rubber Joint, also known as Rubber Bellow or Rubber Expansion Joint, Installed next to mechanical equipment & it use for: absorb pipe movement & stress,
compensate alignment, decrease systems noise, isolate vibration, protect against start up, surge forces. Applications: Hot & Cold Water, Oil & Gas, Air
Rubber Joint - Single Sphere | PN16

Flange End, Suitable mounting between PN16 or Class 150 Flanges
Materials Rubber - Single Sphere Rubber - Double Sphere

Pressure Ratings PN16 - Class 150 PN16 - Class 150
Sr. No Parts Fig No. G101 Fig No. G102
01 Body Neoprene Rubber - EPDM Rubber Neoprene Rubber - EPDM Rubber
02 Fabric Nylon Fabric Nylon Fabric
03 Flange Mils Steel Galvanized -
04 End Unions - Mils Steel Galvanized
05 Wire Carbon Steel Carbon Steel
Sizes 50 65 80 100 125 150 200 250 300 350 400 450 500 600
(L) Face to Face 105 115 135 150 165 180 210 230 245 255 255 255 255 260
Axial Compression 10 13 15 19 19 20 25 25 25 25 25 25 25 25
Axial Elongation 7 7 8 10 12 12 16 16 16 16 16 16 16 16
Horizontal Displacement 10 11 12 13 13 14 22 22 22 22 22 22 22 22
Angular Deflection 15 15 15 15 15 15 15 15 15 15 15 15 15 15
(D) Flange OD - Class 150 153 178 191 229 254 279 343 406 483 533 597 635 699 812
(D) Flange OD - PN16 165 185 200 220 250 285 340 405 460 520 580 640 715 840
Rubber Joint - Double Sphere | PN16

Union end connections
Sizes 20 25 32 40 50 65
(L) Face to Face 180 180 200 210 220 245
Axial Compression 6 6 6 6 6 6
Axial Elongation 22 22 22 22 22 22
Horizontal Displacement 22 22 22 22 22 22
55
Stainless Steel Expansion Joint, Installed next to mechanical equipment & it use for: absorb pipe movement & stress, compensate alignment, decrease systems noise,
isolate vibration, protect against start up, surge forces. Applications: Hot & Cold Water, Oil & Gas, Steam
Stainless Steel Expasion Joint - PN16 | Class 150

Single Axial, Flnage End
Stainless Steel Expansion Joint, Installed next to mechanical equipment & it use for: absorb pipe movement & stress, compensate alignment, decrease systems noise,
isolate vibration, protect against start up, surge forces. Applications: Hot & Cold Water, Oil & Gas, Steam
Materials Stainless Steel Stainless Steel

Pressure Ratings PN16 - Class 150 PN16 - Class 150
Sr. No Parts Fig No. G103 Fig No. G104
01 Body Stainless Steel 304 Stainless Steel 304
02 Flange Materials Fixed or Swivel (Rotating) -
- Flange Installations Mils Steel - Stainless Steel -
- Union Installations - Fixed or Swivel (Rotating)
- Working Pressure 16 Bar 16 Bar
- Test Pressure 24 Bar 24 Bar
- Working Temp 300° 300°
required extended lengths are available against request

Sizes 15 20 25 32 40 50 65 80 100 125 150 200 250 300 350 400 450 500 600
Axial Movement 10 10 10 10 10 25 25 25 25 38 38 50 50 50 45 45 45 45 45
(L) Overall Length 122 122 122 144 144 266 266 266 266 372 372 451 451 451 455 455 455 475 440
(D) Flange OD Cls 150 89 98 208 116 127 153 178 191 229 254 279 343 406 483 533 597 635 699 812
(D) Flange OD - PN16 95 105 115 140 150 165 185 200 220 250 285 340 405 460 520 580 640 715 840
Stainless Steel Expasion Joint - PN16 | Class 150

Single Axial, Threaded or Union End
Stainless Steel Expasion Joint - PN16

Single axial, Threaded or Union End
for FCU’s required extended lengths are available against request

Sizes 15 20 25 32 40 50 65 80 100 125 150 200 250 300 350 400 450 500 600
Axial Movement 10 10 10 10 10 25 25 25 25 38 38 50 50 50 45 45 45 45 45
Overall Length 132 132 132 154 154 208 208 208 208 314 314 352 352 352 325 325 325 343 310
56
Ball valves are quarter-turn, straight through flow valves that have a round closure element with matching rounded seats that permit uniform sealing stress. They
are wide duty valves, able to transfer gases, liquids and liquids with suspended solids (slurries). Applications: Hot & Cold Water, Oil & Gas, Air, Steam
Ball Valve - PN25 | PN32 | PN40

Forged Brass, Lever Operated, Full Bore, Female Threaded End
Ball Valves - PN32 | PN40

Forged Brass Materials, Lever Operated, 2 Pieces, Full Bore
Female Threaded End
Threads to EN 10226-1 comply with BS21

Refer to Page No. 7
Materials Brass Bronze
Pressure Ratings PN25 | PN32 | PN40 PN20
Sr. No Parts Fig No. H101 Fig No. H102
01 Body Brass CW617N Bronze CC491K
02 Ball Brass CW617N Bronze CC491K
03 Stem Brass CW617N Bronze CC491K
04 Ball Seat (Packing) PTFE Teflon
05 Lever Aluminum | Steel
06 O Ring EPDM - PTFE Teflon
Testing Standards - BS 6755 | EN 12266-1 Shell: 60 Bar | Seat: 44 Bar Shell: 37.5 Bar | Seat: 27.5 Bar
Sizes 15 20 25 32 40 50 65 80 100
(L) Face to Face 48 58 69 80 91 108 130 150 178
(H) Height 42 44 57 61 72 77 120 127 250
Ball Valve - PN20

Forged Bronze, Lever Operated, Full Bore, Female Threaded End
Ball Valves - PN20

Forged Bronze Material, Lever Operated, 2 Pieces, Full Bore,
Female Threaded End
new “H” brand embossed on valve body, “SCON” printed on operating lever
Sizes 15 20 25 32 40 50 65 80 100
(L) Face to Face 53 61 71 85 92 114 134 152 182
(H) Height 44 51 56 66 70 83 118 132 150
57
Ball Valve - PN16 | Class 150

S.S. 304, 2 Pieces, Full Bore, Flange End
Flange outer & drilliing to PN16 | Class 150
Ball Valves - Class 150

Stainless Steel 304, 2 Pieces, Full Bore, Flange End
Flange outer & Drilliing to ANSI 16.5 - Class 150
Design & Compliances: EN 558-1 (27), ANSI 16.10, API 608

Materials Stainless Steel Stainless Steel
Pressure Ratings Class 150 PN70 - 1000 PSI
Sr. No Parts Fig No. H103 Fig No. H104
01 Body Stainless Steel 304 Stainless Steel 304
02 Ball Stainless Steel 304 Stainless Steel 304
03 Stem Stainless Steel 304 Stainless Steel 304
04 Ball Seat (Packing) PTFE Teflon
07 Stem Packing Graphite - PTFE Teflon
08 Nut Bolt S.S. 304 ASTM A193 B8
Testing Standards - API 598 | EN 12266-1 Shell: 30 Bar | Seat: 20 Bar
Sizes 15 20 25 32 40 50 65 80 100 125 150 200 250 300 350
(L) Face to Face 108 117 127 140 165 178 190 203 229 356 394 457 533 610 686
(D) OD 89 98 108 117 127 152 178 191 229 254 279 343 406 483 533
(H) Height 129 138 148 160 177 192 210 241 272 306 335 398 456 540 585
Ball Valve - 70 Bar | 1000 PSI

S.S. 304, Lever Operated, 1 Piece, Full Bore, Female Threaded End
Fe
Ball Valves - 70 Bar | 1000 PSI

S.S. 304, Lever Operated, 1 Piece, Full Bore
Female Threaded End Millimeter Dimensions
Sizes 15 20 25 32 40 50 65 80
(L) Face to Face 53 57 68 78 82 94 - -
Fe
(H) Height 35 38 52 57 81 88 - -
58
Ball Valve - PN16

Lever Operated, 2 Pieces, Full Bore, Bolted Bodies, Flange End
Ball Valves - PN16

Design & Compliances: EN 558-1 (27)

Refer to Page No. 7
Sr. No Parts Fig No. H107 Fig No. H108 Fig No. H109
02 Ball S.S. 304 | S.S. 316
03 Stem S.S. 304 | S.S. 316
04 Ball Seat PTFE Teflon
08 Nut Bolt Carbon Steel IS0 8.8 | Galvanized | S.S. 304 ASTM A193 B8
Testing Standards - BS 6755 | EN 12266-1 Shell: 24 Bar | Seat: 18 Bar Shell: 30 Bar | Seat: 20 Bar
 Actuators: Electric | Pneumatic
 Operation: Gear Operated.
Sizes 15 20 25 40 50 65 80 100 125 150 200 250 300 350
(L) Face to Face 108 117 127 165 178 191 203 229 256 267 292 330 356 381
(D) Flange OD 95 105 115 150 165 185 200 220 250 285 340 405 460 520
(H) Height 129 138 148 160 177 192 210 241 272 306 335 398 456 540
59
Ball valves are quarter-turn, straight through flow valves that have a round closure element with matching rounded seats that permit uniform sealing stress.
They are wide duty valves, able to transfer gases, liquids and liquids with suspended solids (slurries). Applications: Hot & Cold Water, Oil & Gas, Air, Steam
Ball valves are quarter-turn, straight through flow valves that have a round closure element with matching rounded seats that permit uniform sealing stress.
They are wide duty valves, able to transfer gases, liquids and liquids with suspended solids (slurries). Applications: Hot & Cold Water, Oil & Gas, Air, Steam
Ball Valve - Class 125 | Class 150

Ball Valves - Class 125 | Class 150

Design & Compliances: ANSI 16.10, API 608

Refer to Page No. 7
Sr. No Parts Fig No. H117 Fig No. H118 Fig No. H119
01 Body Cast Iron ASTM-A126 B Ductile Iron ASTM-A536 Cast Steel ASTM-A216
02 Ball AISI 304 | AISI 316
03 Stem AISI 304 | AISI 316
04 Ball Seat PTFE Teflon
08 Nut Bolt Carbon Steel IS0 8.8 | Galvanized | S.S. 304 ASTM A193 B8
Testing Standards - API 598 Shell: 24 Bar | Seat: 18 Bar Shell: 30 Bar | Seat: 20 Bar
 Actuators: Electric | Pneumatic
 Operation: Gear Operated.
Sizes 15 20 25 40 50 65 80 100 125 150 200 250 300 350
(L) Face to Face 108 117 127 165 178 191 203 229 256 267 292 330 356 381
(D) Flange OD 89 98 108 117 127 152 178 191 229 254 279 343 406 483
(H) Height 129 138 148 160 177 192 210 241 272 306 335 398 456 540
60
Gas Service Valves also known as Gas Shut Off Valves are to be install in gas pipe lines, knowing the location of your main service valve will help you turn off
the gas supply to your entire facility quickly in case of an emergency . Applications: Gas & Air
Gas Service Valves also known as Gas Shut Off Valves are to be install in gas pipe lines, knowing the location of your main service valve will help you turn off
the gas supply to your entire facility quickly in case of an emergency . Applications: Gas & Air
Gas Service Valve - PN16 | Class 150

Female Insulating Union, Lock Wing Type
Screwed End, Female Threaded End
Gas Service Valves - PN16 | Class 150

Female Insulating Union, Lock Wing Type,
Screwed End, Female Threaded
face to face dimensions for the available size 1/2” x 3/4” are 5-1/8” Inches with tolerance of (+-) 1/16 inches
Refer to Page No. 7
Sr. No Parts Fig No. K101 Fig No. K102 Fig No. K103
01 Body Cast Iron EN-GJL-250 Ductile Iron EN-GJL-500 Cast Steel GP240GH
02 Bonnet Cast Iron EN-GJL-250 Ductile Iron EN-GJL-500 Cast Steel GP240GH
03 Plug Brass CW614N Brass CW614N Cast Steel GP240GH
04 Union Nut Cast Iron EN-GJL-250 Ductile Iron EN-GJL-500 Cast Steel GP240GH
05 Tail Piece Carbon Steel Stainless Steel Cr13 Stainless Steel Cr13
06 Insulation Nylon - PTFE Teflon
07 Gasket EPDM - Neoprene
Painting (200-300 Mic) wet blue epoxy paint, corrosion resistant - wet silver paint, corrosion & heat resistant
Sizes (mm) 15 x 20 20 x 25 25 x 32 32 x 40 40 x 50
Sizes (Inches) 1/2” x 3/4” 3/4” x 1” 1” x 1-1/4” 1-1/4” x 1-1/2” 1-1/2” x 2”
61
Air Vents, Air Release, are often fitted at the highest point on a pipeline to continually release unwanted air during system operation to protect against unwanted
surges and maintain system efficiency. Applications: Hot & Cold Water
Air Vents, Air Release or Relief Valves, are often fitted at the highest point on a pipeline to continually release unwanted air during system operation to protect
against unwanted surges and maintain system efficiency. Applications: Hot & Cold Water
Auto Air Vent - Brass | PN16
Female Threaded End
Auto Air Vents - Brass - PN16

Female Threaded End
Threads to EN 10226-1 comply with BS21, screwed end connections

Materials Brass - Air Vents Brass - Water Hammer Arrestor
Sr. No Parts Fig No. V101 Fig No. V102
01 Body Brass CW614N Brass CW617N
02 Top Plate Brass CW614N -
03 Ball PVC -
04 Thread Ring EPDM -
05 Air Plug PVC -
06 Spigot - Brass CW617N
07 Spring - Carbon Steel Spring Wires
08 Disc - Brass CW617N
09 O- Ring - NBR 70
Sizes 15 20 25
(L) Height 61 82 85
(W) Width 39 45 55
Water hammer is a hydraulic phenomenon that occurs when the flow of water in a pipe is forced to stop by the sudden closure of a valve (or, sometimes, also
when a closed pipe is suddenly opened. The magnitude of a water hammer depends on a number of variables, Applications: Pipe Lines
Water hammer is a hydraulic phenomenon that occurs when the flow of water in a pipe is forced to stop by the sudden closure of a valve (or, sometimes, also
when a closed pipe is suddenly opened. The magnitude of a water hammer depends on a number of variables, Applications: Pipe Lines
Water Hammer Arrestor - Brass | PN16

Female Threaded End
Water Hammer Arrestor - Brass - PN16

Female Threaded End
Sizes 15
(L) Height 91
(W) Width 52
62
Air Release, are often fitted at the highest point on a pipeline to continually release unwanted air during system operation to protect against unwanted surges and
maintain system efficiency. Applications: Hot & Cold Water, Air
Air Release, Relief Valves, are often fitted at the highest point on a pipeline to continually release unwanted air during system operation to protect against unwanted
surges and maintain system efficiency. Applications: Hot & Cold Water, Air
Air Release Valve - Single Orifice | PN16 | PN25 | Class 150

Lower Flanged, flange outer & drilling to EN 1092 - BS 4504 | ANSI 16.5
Air Release Valves - Single Orifice - PN16

Lower Flanged, Flange outer & drilling to PN16 - EN 1092 | BS 4504
Design & Compliances: AWWA C512-14, JIS B2063

Refer to Page No. 7
Pressure Ratings PN16 - Class 125 PN16 - PN25 - Class 150 PN16 - PN25 - Class 150
Sr. No Parts Fig No. L101 Fig No. L102 Fig No. L103
03 Float Ball S.S. 304 | S.S. 316
04 Gasket EPDM - Asbestos Free
Painting (200-300 Mic) wet blue epoxy paint, corrosion resistant
 Flange PCD is available in PN16 or PN25 | BS 4504 - EN 1092 or Class 150 - ANSI 16.5
 These valves are also available in higher pressure rating of PN40 & subject to manufacturer acceptance
Sizes 50 80 100 150
(H) Height 250 262 272 335
(W) Width 209 213 240 295
(OD) Flange - PN16 165 200 220 285
(OD) Flange - PN25 165 200 235 300
(OD) Flange - Class 150 152 191 229 279
63
Air Release, are often fitted at the highest point on a pipeline to continually release unwanted air during system operation to protect against unwanted surges and
maintain system efficiency. Applications: Hot & Cold Water, Air
Air Release, Relief Valves, are often fitted at the highest point on a pipeline to continually release unwanted air during system operation to protect against
unwanted surges and maintain system efficiency. Applications: Hot & Cold Water, Air
Air Release Valve - Double Orifice | PN16 | PN25 | Class 150

Lower Flanged, flange outer & drilling to EN 1092 - BS 4504 | ANSI 16.5
Design & Compliances: AWWA C512-14, JIS B2063

Refer to Page No. 7
Pressure Ratings PN16 - Class 125 PN16 - PN25 - Class 150 PN16 - PN25 - Class 150
Sr. No Parts Fig No. L104 Fig No. L105 Fig No. L106
03 Float Ball S.S. 304 | S.S. 316
04 Gasket EPDM - Asbestos Free
Painting (200-300 Mic) wet blue epoxy paint, corrosion resistant
 Flange PCD is available in PN16 or PN25 | BS 4504 - EN 1092 or Class 150 - ANSI 16.5
 These valves are also available in higher pressure rating of PN40 & subject to manufacturer acceptance
Sizes 50 80 100 150 200 250 300
(H) Height 275 320 370 450 505 610 690
(W) Width 305 335 430 550 695 790 905
(OD) Flange - PN16 165 200 220 285 340 405 460
(OD) Flange - PN25 165 200 235 300 360 425 485
(OD) Flange - Class 150 152 191 229 279 343 406 483
64
Pipe flanges that are typically made from forged materials and have machined surfaces, It is use to connect the valves with pipes or pipe fittings.
Flanges - Raised Face | Fig No. M101

BS 4504 | EN 1092
A = PCD Pinch Circle

D = Outer Dia
C = Raised Face Dia
B = Thickness
RF = Raised Face Thickness
F = Bolt Dia
N = No. of Holes
Millimeter Dimensions - Raised Face - PN10 - sizes above than following are subject to manufacture against request
Flanges
Size - 15
Raised20
Face |25
Fig No.32M10140 50 65 80 100 125 150 200 250 300 350 400 450 500 600 700 800 900
BS 4504 | EN 1092
A 65 75 85 100 110 125 145 160 180 210 240 295 350 400 460 515 565 620 725 840 950 1050
A D =95PCD Pinch
105 Circle
115 140 150 165 185 200 220 250 285 340 395 445 505 565 615 670 780 895 1015 1115
D = Outer Dia
C 45 58 68 78 88 102 122 138 158 188 212 268 320 370 430 482 532 585 685 800 905 1005
C = Raised Face Dia
B B =14Thickness
16 16 16 16 18 18 20 20 22 22 24 26 26 26 26 26 28 28 30 32 34
RF RF =2Raised2Face Thickness
2 2 3 3 3 3 3 3 3 3 3 4 4 4 4 4 5 5 5 5
F = Bolt Dia
N F 14
= No. of14Holes14 18 18 18 18 18 18 18 22 22 22 22 22 26 26 26 30 30 33 33
N 4 4 4 4 4 4 4 8 8 8 8 8 12 12 16 16 20 20 20 24 24 28
Size 15 20 25 32 40 50 65 80 100 125 150 200 250 300 350 400 450 500 600 700 800 900
A 65 75 85 100 110 125 145 160 180 210 240 295 355 410 470 525 585 650 770 840 950 1050
D 95 105 115 140 150 165 185 200 220 250 285 340 405 460 520 580 640 715 840 910 1025 1125
C 45 58 68 78 88 102 122 138 158 188 212 268 320 378 438 590 550 610 725 800 900 1005
B 14 16 16 16 16 18 18 20 20 22 22 24 26 28 30 32 32 36 40 42 42 44
RF 2 2 2 2 3 3 3 3 3 3 3 3 3 4 4 4 4 4 5 5 5 5
F 14 14 14 18 18 18 18 18 18 18 22 22 26 26 26 30 30 36 36 36 39 39
N 4 4 4 4 4 4 4 8 8 8 8 12 12 12 16 16 20 20 20 24 24 28
Size 15 20 25 32 40 50 65 80 100 125 150 200 250 300 350 400 450 500 600 700 800 900
A 65 75 85 100 110 125 145 160 190 220 250 310 370 430 490 550 600 660 770 875 990 1090
D 95 105 115 140 150 165 185 200 235 270 300 360 425 485 555 620 670 730 845 960 1085 1185
C 45 58 68 78 88 102 122 138 162 188 218 278 335 390 450 505 555 615 725 820 930 1030
B 16 18 18 18 18 20 22 24 24 26 28 30 32 34 38 40 40 44 46 50 64 68
RF 2 2 2 2 3 3 3 3 3 3 3 3 3 4 4 4 4 4 5 5 5 5
F 14 14 14 18 18 18 18 18 22 26 26 26 30 30 33 36 36 36 39 42 48 48
N 4 4 4 4 4 4 8 8 8 8 8 12 12 16 16 16 20 20 20 24 24 28
Size 15 20 25 32 40 50 65 80 100 125 150 200 250 300 350 400 450 500 600 700 800 900
A 65 75 85 100 110 125 145 160 190 220 250 320 385 450 510 585 610 670 795 900 1050 1140
D 95 105 115 140 150 165 185 200 235 270 300 375 450 515 580 660 685 755 890 995 1165 1250
C 45 58 68 78 88 102 122 138 162 188 218 285 345 410 465 535 560 615 735 840 960 1070
B 16 18 18 18 18 18 22 24 24 26 26 34 38 42 46 50 50 52 54 64 72 78
RF 2 2 2 2 3 3 3 3 3 3 3 3 3 4 4 4 4 4 5 5 5 5
F 14 14 14 18 18 18 18 18 22 26 28 30 33 33 36 39 39 42 48 48 62 56
N 4 4 4 4 4 4 8 8 8 8 8 12 12 16 16 16 20 20 20 24 24 28
65
Flanges - Blind | Fig No. M102

BS 4504 | EN 1092

D = Outer Dia
B = Thickness
F = Bolt Dia
N = No. of Holes
Flanges - Blind | Fig No. M102

BS 4504 | EN
Millimeter 1092
Dimensions - Blind Flanges - PN10 - sizes above than following are subject to manufacture against request
A Size =15 20 Circle

PCD Pinch 25 32 40 50 65 80 100 125 150 200 250 300 350 400 450 500 600 700 800 900
D = Outer Dia
B A =65Thickness
75 85 100 110 125 145 160 180 210 240 295 350 400 460 515 565 620 725 840 950 1050
F = Bolt Dia
D 95 105 115 140 150 165 185 200 220 250 285 340 395 445 505 565 615 670 780 895 1015 1115
N = No. of Holes
B 14 16 16 16 16 18 18 20 20 22 22 24 26 26 26 26 26 28 28 30 32 34
F 14 14 14 18 18 18 18 18 18 18 22 22 22 22 22 26 26 26 30 30 33 33
N 4 4 4 4 4 4 4 8 8 8 8 8 12 12 16 16 20 20 20 24 24 28
Millimeter Dimensions - Blind Flanges - PN16 - sizes above than following are subject to manufacture against request
Size 15 20 25 32 40 50 65 80 100 125 150 200 250 300 350 400 450 500 600 700 800 900
A 65 75 85 100 110 125 145 160 180 210 240 295 355 410 470 525 585 650 770 840 950 1050
D 95 105 115 140 150 165 185 200 220 250 285 340 405 460 520 580 640 715 840 910 1025 1125
B 14 16 16 16 16 18 18 20 20 22 22 24 26 28 30 32 32 36 40 42 42 44
F 14 14 14 18 18 18 18 18 18 18 22 22 26 26 26 30 30 36 36 36 39 39
N 4 4 4 4 4 4 4 8 8 8 8 12 12 12 16 16 20 20 20 24 24 28
Size 15 20 25 32 40 50 65 80 100 125 150 200 250 300 350 400 450 500 600 700 800 900
A 65 75 85 100 110 125 145 160 190 220 250 310 370 430 490 550 600 660 770 875 990 1090
D 95 105 115 140 150 165 185 200 235 270 300 340 425 485 555 620 670 730 845 960 1085 1185
B 16 18 18 18 18 20 22 24 24 26 28 30 32 34 38 40 40 44 46 50 64 68
F 14 14 14 18 18 18 18 18 22 26 26 26 30 30 33 36 36 36 39 42 48 48
N 4 4 4 4 4 4 8 8 8 8 8 12 12 16 16 16 20 20 20 24 24 28
Size 15 20 25 32 40 50 65 80 100 125 150 200 250 300 350 400 450 500 600 700 800 900
A 65 75 85 100 110 125 145 160 190 220 250 320 385 450 510 585 610 670 795 900 1050 1140
D 95 105 115 140 150 165 185 200 235 270 300 375 450 515 580 660 685 755 890 995 1165 1250
B 16 18 18 18 18 18 22 24 24 26 26 34 38 42 46 50 50 52 54 64 72 78
F 14 14 14 18 18 18 18 18 22 26 28 30 33 33 36 39 39 42 48 48 62 56
N 4 4 4 4 4 4 8 8 8 8 8 12 12 16 16 16 20 20 20 24 24 28
66
Flanges - Welding Neck | Fig No. M103

BS 4504 | EN 1092

D = Outer Dia
C = Raised Face Dia
B = Thickness
F = Bolt Dia
N = No. of Holes
M = Neck Width
H = Overall Height
Welding Neck - PN16 - sizes above than following are subject to manufacture against request
Flanges
Size - Welding
15 20Neck25
| Fig No.
32 M103
40 50 65 80 100 125 150 200 250 300 350 400 450 500 600 700 800 900
BS 4504 | EN 1092
A 65 75 85 100 110 125 145 160 180 210 240 295 355 410 470 525 585 650 770 840 950 1050
A D =95
PCD Pinch Circle
105 115 140 150 165 185 200 220 250 285 340 405 460 520 580 640 715 840 910 1025 1125
D = Outer Dia
C C =45
Raised58 68
Face Dia 78 88 102 122 138 158 188 212 268 320 378 438 590 550 610 725 800 900 1005
B = Thickness
B 14 16 16 16 16 18 18 20 20 22 22 24 26 28 30 32 32 36 40 42 42 44
F RF 2 Dia2
= Bolt 2 2 3 3 3 3 3 3 3 3 3 4 4 4 4 4 5 5 5 5
N = No. of Holes
F 14 14 14 18 18 18 18 18 18 18 22 22 26 26 26 30 30 36 36 36 39 39
M = Neck Width
H N = Overall
4 4Height4 4 4 4 4 8 8 8 8 12 12 12 16 16 20 20 20 24 24 28
M 32 40 46 56 64 74 92 105 131 156 184 235 292 344 390 445 490 548 670 755 855 955
H 38 40 40 42 45 45 45 50 52 55 55 62 70 78 82 83 83 84 88 104 108 118
Size 15 20 25 32 40 50 65 80 100 125 150 200 250 300 350 400 450 500 600 700 800 900
A 65 75 85 100 110 125 145 160 190 220 250 310 370 430 490 550 600 660 770 875 990 1090
D 95 105 115 140 150 165 185 200 235 270 300 360 425 485 555 620 670 730 845 960 1085 1185
C 45 58 68 78 88 102 122 138 162 188 218 278 335 390 450 505 555 615 725 820 930 1030
B 16 18 18 18 18 20 22 24 24 26 28 30 32 34 38 40 40 44 46 50 64 68
RF 2 2 2 2 3 3 3 3 3 3 3 3 3 4 4 4 4 4 5 5 5 5
F 14 14 14 18 18 18 18 18 22 26 26 26 30 30 33 36 36 36 39 42 48 48
N 4 4 4 4 4 4 8 8 8 8 8 12 12 16 16 16 20 20 20 24 24 28
M 32 40 46 56 64 75 90 105 134 162 192 244 298 352 398 452 500 558 660 760 864 968
H 38 40 40 42 45 48 52 58 65 68 75 80 88 92 100 110 110 125 125 129 138 148
Size 15 20 25 32 40 50 65 80 100 125 150 200 250 300 350 400 450 500 600
A 65 75 85 100 110 125 145 160 190 220 250 320 385 450 510 585 610 670 795
D 95 105 115 140 150 165 185 200 235 270 300 375 450 515 580 660 685 755 890
C 45 58 68 78 88 102 122 138 162 188 218 285 345 410 465 535 560 615 735
B 16 18 18 18 18 18 22 24 24 26 26 34 38 42 46 50 50 52 54
RF 2 2 2 2 3 3 3 3 3 3 3 3 3 4 4 4 4 4 5
F 14 14 14 18 18 18 18 18 22 26 28 30 33 33 36 39 39 42 48
N 4 4 4 4 4 4 8 8 8 8 8 12 12 16 16 16 20 20 20
M 32 40 46 56 64 75 90 105 134 162 192 244 306 362 408 462 500 562 666
H 38 40 40 42 45 48 52 58 65 68 75 88 105 115 125 135 135 140 150
67
Flanges - Slip On | Fig No. N101

ASNI 16.5 | Class 150

D = Outer Dia
C = Raised Face Dia
B = Thickness
F = No. of Holes
N = Bolt Hole Dia
M = Neck Width
H = Overall Height
Slip-On Raised Face - Class 150 - sizes above than following are subject to manufacture against request
Size16.5 | Class
ASNI 1/2” 150 3/4” 1” 1.25” 1.5” 2” 2.5” 3” 4” 5” 6” 8” 10“ 12” 14”
A 60.3 69.8 79.4 88.9 98.4 120.6 139.7 152.4 190.5 215.9 241.3 298.4 361.9 431.8 476.2
D 88.9 98.4 107.9 117.5 127.0 152.4 177.8 190.5 228.6 254.0 279.4 342.9 406.4 482.6 533.4
D = Outer Dia
C C = 34.9 42.9
Raised Face Dia 50.8 63.5 73.0 92.1 104.8 127.0 157.2 185.7 215.9 269.9 323.8 381.0 412.7
B B = 11.1
Thickness 12.7 14.3 15.9 17.5 19.0 22.2 23.8 23.8 23.8 25.4 28.6 30.2 31.7 34.9
N RF 1.6 Hole Dia
= Bolt 1.6 1.6 1.6 1.6 1.6 1.6 1.6 1.6 1.6 1.6 1.6 1.6 1.6 1.6
F F = No.
4 of Holes4 4 4 4 4 4 4 8 8 8 8 12 12 12
M = Neck Width
N 15.9 15.9 15.9 15.9 15.9 19.0 19.0 19.0 19.0 22.2 22.2 22.2 25.4 25.4 28.6
H = Overall Height
M 30.2 38.1 49.2 58.8 65.1 77.8 90.5 107.9 134.9 163.6 192.1 246.1 304.8 365.1 400.0
H 15.9 15.9 17.5 20.6 22.2 25.4 28.6 30.2 33.3 36.5 39.7 44.4 49.2 55.6 57.1
Size 16” 18” 20” 22” 24” 26” 28” 30” 32” 34” 36” 38” 40” 42”
A 539.7 577.8 635.0 692.1 749.3 806 864 914 978 1029 1086 1149 1200 1257
D 596.9 635.0 698.5 749.3 812.8 870.0 927.1 984.3 1060.5 1111.3 1168.4 1238.3 1289.0 1346.2
C 469.9 533.4 584.2 641.2 692.1 ASME 749.3 800.1 857.3 914.4 965.2 1022.4 1073.2 1124.0 1193.8
B 36.5 39.7 42.9 46.0 47.6 16.47 68.3 71.4 74.7 81.0 82.6 90.4 90.4 90.4 96.8
RF 1.6 1.6 1.6 1.6 1.6 Series 1.6 1.6 1.6 1.6 1.6 1.6 1.6 1.6 1.6
F 16 16 20 20 20 A 24 28 28 28 32 32 32 36 36
N 28.6 31.7 31.7 34.9 34.9 35.1 35.1 35.1 41.1 41.1 41.1 41.1 41.1 41.1
M 457.2 504.8 558.8 609.6 663.6 676.1 726.9 781.1 831.9 882.7 933.5 990.6 1041.4 1092.2
H 63.5 68.3 73.0 79.4 82.5 120.7 125.5 136.7 144.5 149.4 157.2 157.2 163.6 171.5
Flanges - Blind | Fig No. N102


D = Outer Dia
B = Thickness
F = No. of Holes
N = Bolt Dia
Slip-On Blind - Class 150 - for larger sizes: slip-on flange dimensions will be followed, except C, RF, M, H
Size 1/2” 3/4” 1” 1.25” 1.5” 2” 2.5” 3” 4” 5” 6” 8” 10“ 12” 14”
A 60.3 69.8 79.4 88.9 98.4 120.6 139.7 152.4 190.5 215.9 241.3 298.4 361.9 431.8 476.2
Flanges
D - Blind
88.9 | Fig98.4
No. N102107.9 117.5 127.0 152.4 177.8 190.5 228.6 254.0 279.4 342.9 406.4 482.6 533.4
B 11.1 12.7 14.3 15.9 17.5 19.0 22.2 23.8 23.8 23.8 25.4 28.6 30.2 31.7 34.9
A F = PCD
4 Pinch Circle
4 4 4 4 4 4 4 8 8 8 8 12 12 12
D = Outer Dia
N 15.9 15.9 15.9 15.9 15.9 19.0 19.0 19.0 19.0 22.2 22.2 22.2 25.4 25.4 28.6
B = Thickness
F = Bolt Dia 68
N = No. of Holes


D = Outer Dia
C = Raised Face Dia
B = Thickness
F = No. of Holes
N = Bolt Hole Dia
M = Neck Width
H = Overall Height
Size 1/2” 3/4” 1” 1.25” 1.5” 2” 2.5” 3” 4” 5” 6” 8” 10“ 12” 14”
A 66.7 82.5 88.9 98.4 114.3 127.0 149.2 168.3 200.0 234.9 269.9 330.2 387.3 450.8 514.3
D 95.6 117.5 123.8 133.3 155.6 165.1 190.5 209.5 254.0 279.4 317.5 381.0 444.5 520.7 584.2
C 34.9 42.9 50.8 63.5 73.0 92.1 104.8 127.0 157.2 185.7 215.9 269.9 323.4 381.0 412.7
ASNIB16.5 | Class
14.3300 15.9 17.5 19.0 20.6 22.2 25.4 28.6 31.7 34.9 36.5 41.3 47.6 50.8 54.0
RF 1.6 1.6 1.6 1.6 1.6 1.6 1.6 1.6 1.6 1.6 1.6 1.6 1.6 1.6 1.6
F 4 4 4 4 4 8 8 8 8 8 12 12 16 16 20
D = Outer Dia
C N 15.9 Face19.0
= Raised Dia 19.0 19.0 19.0 19.0 22.2 22.2 22.2 22.2 22.2 25.4 28.6 31.7 31.7
B M = Thickness
38.1 476. 54.0 63.5 69.8 84.1 100.0 117.5 146.0 177.8 206.4 260.3 320.7 374.6 425.4
N H 22.2 25.4
= Bolt Hole Dia 27.0 27.0 30.2 33.3 38.1 42.9 47.6 50.8 52.4 61.9 66.7 73.0 76.2
F = No. of Holes
M = Neck Width
HSlip-On Raised FaceHeight
= Overall - Class 300 - sizes above than following are subject to manufacture against request
Size 16” 18” 20” 22” 24” 26” 28” 30” 32” 34” 36” 38” 40” 42”
A 571.5 628.6 685.8 742.9 812.8 876.0 940.0 997.0 1054.0 1105.0 1168.0 1092.0 1156.0 1207.0
D 647.7 711.2 774.7 838.2 914.4 971.6 1035.1 1092.0 1149.4 1206.5 1270.0 1168.4 1238.3 1289.1
C 469.9 533.4 584.2 641.2 692.1 ASME 749.3 800.1 857.3 914.4 965.2 1022.4 1028.7 1085.9 1136.7
B 57.2 60.3 63.5 66.7 69.8 16.47 79.2 85.9 91.9 98.6 101.6 104.6 108.0 114.3 119.1
RF 1.6 1.6 1.6 1.6 1.6 Series 1.6 1.6 1.6 1.6 1.6 1.6 1.6 1.6 1.6
F 20 24 24 24 24 A 28 28 28 28 28 32 32 32 32
N 34.9 34.9 34.9 41.3 41.3 44.5 44.5 47.8 50.8 50.8 53.8 41.1 44.5 44.5
M 482.6 533.4 584.2 641.2 701.7 720.9 774.7 827.0 881.1 936.8 990.6 993.6 1054.6 1098.6
H 82.5 88.9 95.2 101.6 106.4 184.2 196.9 209.6 222.3 231.6 241.3 180.8 193.5 200.2
Flanges - Blind | Fig No. N104


D = Outer Dia
B = Thickness
F = No. of Holes
N = Bolt Dia
Size 1/2” 3/4” 1” 1.25” 1.5” 2” 2.5” 3” 4” 5” 6” 8” 10“ 12” 14”
A 66.7 82.5 88.9 98.4 114.3 127.0 149.2 168.3 200.0 234.9 269.9 330.2 387.3 450.8 514.3
D 95.6 117.5 123.8 133.3 155.6 165.1 190.5 209.5 254.0 279.4 317.5 381.0 444.5 520.7 584.2
Flanges
B
- Blind
14.3
| Fig No. N104
15.9 17.5 19.0 20.6 22.2 25.4 28.6 31.7 34.9 36.5 41.3 47.6 50.8 54.0
F 4 4 4 4 4 8 8 8 8 8 12 12 16 16 20
A N = PCD
15.9Pinch Circle
19.0 19.0 19.0 19.0 19.0 22.2 22.2 22.2 22.2 22.2 25.4 28.6 31.7 31.7
D = Outer Dia
B = Thickness 69
F = Bolt Dia
N = No. of Holes
Flanges - Welding Neck | Fig No. N105


D = Outer Dia
C = Raised Face Dia
B = Thickness
F = No. of Holes
N = Bolt Hole Dia
M = Neck Width
H = Overall Height
Welding Neck - Class 150 - sizes above than following are subject to manufacture against request
Size 1/2” 3/4” 1” 1.25” 1.5” 2” 2.5” 3” 4” 5” 6” 8” 10“ 12” 14”
A 60.3 69.8 79.4 88.9 98.4 120.6 139.7 152.4 190.5 215.9 241.3 298.4 361.9 431.8 476.2
D 88.9 98.4 107.9 117.5 127.0 152.4 177.8 190.5 228.6 254.0 279.4 342.9 406.4 482.6 533.4
C 34.9 42.9 50.8 63.5 73.0 92.1 104.8 127.0 157.2 185.7 215.9 269.9 323.8 381.0 412.7
B 11.1 12.7 14.3 15.9 17.5 19.0 22.2 23.8 23.8 23.8 25.4 28.6 30.2 31.7 34.9
RF 1.6 1.6 1.6 1.6 1.6 1.6 1.6 1.6 1.6 1.6 1.6 1.6 1.6 1.6 1.6
A F = PCD
4 Pinch Circle
4 4 4 4 4 4 4 8 8 8 8 12 12 12
D = Outer Dia
C N 15.9 15.9
= Raised Face Dia 15.9 15.9 15.9 19.0 19.0 19.0 19.0 22.2 22.2 22.2 25.4 25.4 28.6
B M = Thickness
21.3 26.7 33.5 42.2 48.3 60.3 73.1 88.9 114.3 141.2 168.4 219.1 273.0 323.8 355.6
H 47.6 52.4 55.6 57.1 61.9 63.5 69.8 69.8 76.2 88.9 88.9 101.6 101.6 114.3 127.0
N = Bolt Hole Dia
F = No. of Holes
M = Neck Width
H = Overall Height


D = Outer Dia
C = Raised Face Dia
B = Thickness
F = No. of Holes
N = Bolt Hole Dia
M = Neck Width
H = Overall Height
Welding Neck - Class 300 - sizes above than following are subject to manufacture against request
Size 1/2” 3/4” 1” 1.25” 1.5” 2” 2.5” 3” 4” 5” 6” 8” 10“ 12” 14”
A 66.7 82.5 88.9 98.4 114.3 127.0 149.2 168.3 200.0 234.9 269.9 330.2 387.3 450.8 514.3
D 95.6
ASNI 16.5 | Class 300 117.5 123.8 133.3 155.6 165.1 190.5 209.5 254.0 279.4 317.5 381.0 444.5 520.7 584.2
C 34.9 42.9 50.8 63.5 73.0 92.1 104.8 127.0 157.2 185.7 215.9 269.9 323.4 381.0 412.7
B 14.3 15.9 17.5 19.0 20.6 22.2 25.4 28.6 31.7 34.9 36.5 41.3 47.6 50.8 54.0
D = Outer Dia
C RF 1.6 Face1.6
= Raised Dia 1.6 1.6 1.6 1.6 1.6 1.6 1.6 1.6 1.6 1.6 1.6 1.6 1.6
B F = Thickness
4 4 4 4 4 8 8 8 8 8 12 12 16 16 20
N N 15.9Hole Dia
= Bolt 19.0 19.0 19.0 19.0 19.0 22.2 22.2 22.2 22.2 22.2 25.4 28.6 31.7 31.7
F M = No.
21.3of Holes
26.7 33.5 42.2 48.3 60.3 73.1 88.9 114.3 141.2 168.4 219.1 273.0 323.8 355.6
M = Neck Width
H 52.4 57.1 61.9 65.1 68.3 69.8 76.2 79.4 85.7 98.4 98.4 111.1 117.5 130.2 142.9
H = Overall Height
70
Brass Balancing Valves - DN15 - Fig No. F101

OPEN 0.5 1.0 1.5 2.0 2.5 3.0
Kv (m3/h) 0.66 0.89 1.07 1.37 1.96 2.33
OPEN 3.5 4.0 4.5 5.0 6.0
Kv (m3/h) 2.60 2.79 2.95 3.06 3.17
Bronze Balancing Valves - DN15 - Fig No. F102

OPEN 0.5 1.0 1.5 2.0
Kv (m3/h) 0.17 0.29 0.45 0.61
OPEN 2.5 3.0 3.5 4.0
Kv (m3/h) 0.80 1.18 1.56 1.72
71

OPEN 0.5 1.0 1.5 2.0
Kv. Avg 0.15 0.26 0.41 0.78
OPEN 2.5 3.0 3.5 4.0
Kv. Avg 1.40 2.13 2.72 2.97

OPEN 0.5 1.0 1.5 2.0 2.5 3.0
Kv (m3/h) 0.73 0.95 1.14 1.57 2.18 2.78
OPEN 3.5 4.0 4.5 5.0 6.0
Kv (m3/h) 3.31 3.73 3.95 4.15 4.46
72

OPEN 0.5 1.0 1.5 2.0
Kv. Avg 0.40 0.78 1.20 1.59
OPEN 2.5 3.0 3.5 4.0
Kv. Avg 1.94 2.78 3.95 4.75

OPEN 0.5 1.0 1.5 2.0 2.5 3.0
Kv (m3/h) 0.93 1.19 1.52 2.07 2.60 3.30
OPEN 3.5 4.0 4.5 5.0 6.0
Kv (m3/h) 3.88 4.61 5.29 6.10 7.63
73

OPEN 0.5 1.0 1.5 2.0
Kv. Avg 0.65 1.39 2.04 3.67
OPEN 2.5 3.0 3.5 4.0
Kv. Avg 6.47 8.57 9.63 10.25

OPEN 0.5 1.0 1.5 2.0 2.5 3.0
Kv (m3/h) 1.52 2.47 3.18 4.22 4.91 6.23
OPEN 3.5 4.0 4.5 5.0 6.0
Kv (m3/h) 7.15 8.28 9.16 10.37 12.10
74

OPEN 0.5 1.0 1.5 2.0
Kv. Avg 0.93 1.95 2.80 5.04
OPEN 2.5 3.0 3.5 4.0
Kv. Avg 9.17 13.31 15.46 16.83

OPEN 0.5 1.0 1.5 2.0 2.5 3.0
Kv (m3/h) 1.63 2.79 3.50 4.95 5.97 7.50
OPEN 3.5 4.0 4.5 5.0 6.0
Kv (m3/h) 8.58 10.58 11.77 13.78 17.00
75

OPEN 0.5 1.0 1.5 2.0
Kv. Avg 1.71 3.03 4.40 8.22
OPEN 2.5 3.0 3.5 4.0
Kv. Avg 14.89 20.67 24.49 27.26

OPEN 0.5 1.0 1.5 2.0 2.5 3.0
Kv (m3/h) 2.66 4.18 5.32 7.28 9.20 11.30
OPEN 3.5 4.0 4.5 5.0 6.0
Kv (m3/h) 13.20 15.90 18.20 21.00 26.30
76
Balancing Valves - DN65

OPEN 1.5 2 3 4
Kv (m3/h) 5 15 45 79
OPEN 5 6 7
Kv (m3/h) 103 118 129

OPEN 1.5 2 3 4
Kv (m3/h) 4 12 45 79
OPEN 5 6 7 8
Kv (m3/h) 107 127 140 48
77

OPEN 1.5 2 3 4
Kv (m3/h) 12 29 78 142
OPEN 5 6 7 8
Kv (m3/h) 195 234 265 296

OPEN 1.5 2 3 4 5 6 7
Kv (m3/h) 8 16 48 84 144 197 270
OPEN 8 9 10 11 12 13
Kv (m3/h) 346 389 436 454 482 509
78

OPEN 1.5 2 3 4 5 6 7 8
Kv (m3/h) 7 22 53 93 160 250 322 390
OPEN 9 10 11 12 13 14 15
Kv (m3/h) 435 482 517 556 606 651 699

OPEN 0.5 1 2 3 4 5
Kv (m3/h) 28 39 55 100 216 341
OPEN 6 7 8 9 10 11
Kv (m3/h) 430 508 561 619 667 710
79

OPEN 0.5 1 2 3 4 5
Kv (m3/h) 44 62 87 164 345 543
OPEN 6 7 8 9 10 11
Kv (m3/h) 694 824 925 1022 1110 1188

OPEN 0.5 1 2 3 4 5
Kv (m3/h) 45 57 90 141 332 634
OPEN 6 7 8 9 10 11
Kv (m3/h) 825 1018 1170 1285 1394 1504
80

SCON Valves, Catalogue E10 PDF

Uploaded by

Copyright:

Available Formats

SCON Valves, Catalogue E10 PDF

Uploaded by

Document Information

Original Title

Copyright

Available Formats

Share this document

Share or Embed Document

Sharing Options

Did you find this document useful?

Is this content inappropriate?

Copyright:

Available Formats

SCON Valves, Catalogue E10 PDF

Uploaded by

Copyright:

Available Formats

[email protected] | [email protected].

INCASE OF ANY QUESTION, PELASE WRITE TO: [email protected]

High Quality - Most Reliable - Most Economical

SAFCO’s corporate strategy to apply the most advance procedures exclusively

 Sizes availability DN15 - DN900

Implementations of all procedures are established in manual and system, in

Page No. Index

Flexible Joints - Rubber & Stainless Steel

Gas Service Valves

Auto Air Vents - Water Hammer Arrestor

Air Release Valves

Chemical Analysis Cast Iron Ductile Iron Cast Steel

Minimum Mechanical Properties Cast Iron Ductile Iron Cast Steel

Working Comparison: Area Cast Iron Ductile Iron Cast Steel

Chemical Composition Compliances

Chemical Composition Compliances

Valves Working Pressure & Temperature Ratings

Brass Bronze Cast Iron

PSI PSI PSI

-20 to 150 -29 to 66 200 225 200

Valves Working Pressure & Temperature Ratings

Ductile Iron Cast Steel Cast Steel

PSI PSI PSI

-20 to 150 -29 to 66 250 285 740

Gate Valve - Brass | PN16

Gate Valve - Bronze | PN20 | Class 150

Gate Valve - Forged Steel | Class 800

Gate Valve - Stainless Steel 304 | PN20 | Class 150

Gate Valve - PN10 | PN16

Design & Compliances: EN 1171, DIN 3202 F4, EN 558-1 (14)

Gate Valve - PN10 | PN16

Design & Compliances: EN 1171, DIN 3202 F4, EN 558-1 (14)

Gate Valve - PN16

Gate Valve - PN16

Gate Valve - PN25

Design & Compliances: EN 1171, EN 558-1 (3), BS 5150, BS 5163

Gate Valve - PN25

Design & Compliances: EN 1171, EN 558-1 (3), BS 5150, BS 5163

Gate Valve - Class 125 | Class 150

Gate Valve - Class 125 | Class 150

Gate valves also known as Sluice Valves, Isolating Valves

Gate Valve - Class 300

Design & Compliances: API 600, ANSI 16.10

Gate Valve - Class 300

Design & Compliances: API 600, ANSI 16.10

Globe Valve - Bronze | PN20

Globe Valve - Bronze | Class 150

Globe Valve - Forged Steel | Class 800

Globe Valve - Stainless Steel 304 | PN20 | Class 150

Globe Valves - PN16

Globe Valves - PN16

Design & Compliances: EN 13789, EN 558 (10), BS 5153

Globe Valve - Bellow Seated | PN16

Globe Valve - Y Type | PN16

Globe Valve - PN25

Globe Valve - PN25

Design & Compliances: EN 13789, EN 558 (10), BS 5153

Globe Valve - Bellow Seated | PN25

Globe Valve - Y Type | PN25