Ahb 5

AHB5 PROTOCOL
INTRODUCTION
AMBA AHB is a bus interface suitable for high-performance synthesizable designs. It defines the interface between
components, such as masters, interconnects, and slaves.
AMBA AHB implements the features required for high-performance, high clock frequency systems including:
Burst transfers. Wide data bus configurations, 64, 128, 256, 512, and 1024 bits.
Single clock-edge operation. AHB also supports multi-master designs by the use of an interconnect component that
Non-tristate implementation. provides arbitration and routing signals from different masters to the appropriate slaves.
The bus interconnect logic consists of one address decoder and a slave-to-master multiplexor. The decoder monitors the
address from the master so that the appropriate slave is selected and the multiplexor routes the corresponding slave
output data back to the master.
Figure 1-1 shows a single master AHB system design with the AHB master and three AHB slaves.
SLAVE INTERFACE:
• The slave signals back to the master • The completion or extension of the bus transfer.
The success or failure of the bus transfer.
INTERCONNECT:
An interconnect component provides the connection between masters and slaves in a system.
A single master system only requires the use of a Decoder and Multiplexor, as described in the following sections.
A multi-master system requires the use of an interconnect that provides arbitration and the routing of signals from
different masters to the appropriate slaves. This routing is required for address, control, and write data signaling.
Further details of the different approaches used for multi-master systems, such as single layer or multi-layer
interconnects, are not provided within this specification.
DECODER AND MULTIPLEXER:

DECODER
This component decodes the address of each transfer and provides a select signal for the slave that is involved in the
transfer. It also provides a control signal to the multiplexor.
MULTIPLEXER
A slave-to-master multiplexor is required to multiplex the read data bus and response signals from the slaves to the
master. The decoder provides control for the multiplexer.
Operation:
The master starts a transfer by driving the address and control signals. These signals provide information about the
address, direction, width of the transfer, and indicate if the transfer forms part of a burst. Transfers can be:
• Single.
• Incrementing bursts that do not wrap at address boundaries.
• Wrapping bursts that wrap at particular address boundaries.
• The write data bus moves data from the master to a slave, and the read data bus moves data from a slave to the master.
Every transfer consists of:
• Address phase One address and control cycle.
• Data phase One or more cycles for the data.
HREADY and HRESP:
A slave can request that the master extends the data phase by using HREADY.
This signal, when LOW, causes wait states to be inserted into the transfer and enables the slave to have extra time to
provide or sample data.
The slave uses HRESP to indicate the success or failure of a transfer.
Basic Transfers:
A transfer consists of two phases:
• Address Lasts for a single HCLK cycle unless its extended by the previous bus transfer.
• Data Might require several HCLK cycles. Use the HREADY signal to control the number of clock cycles required to complete
the transfer.
• HWRITE controls the direction of data transfer to or from the master. Therefore, when:
• HWRITE is HIGH, it indicates a write transfer and the master broadcasts data on the write data bus, HWDATA[31:0]
• HWRITE is LOW, a read transfer is performed and the slave must generate the data on the read data bus, HRDATA[31:0].
Memory Types
Slave Transfer Responses

Reset Signal:
The reset signal, HRESETn, is the only active LOW signal in the protocol and is the primary reset for all bus elements. The
reset can be asserted asynchronously, but is deasserted synchronously after the rising edge of HCLK.
During reset all masters must ensure the address and control signals are at valid levels and that HTRANS[1:0] indicates
IDLE.
During reset all slaves must ensure that HREADYOUT is HIGH.

Ahb 5

Uploaded by

Copyright:

Available Formats

Ahb 5

Uploaded by

Document Information

Original Title

Copyright

Available Formats

Share this document

Share or Embed Document

Sharing Options

Did you find this document useful?

Is this content inappropriate?

Copyright:

Available Formats

Ahb 5

Uploaded by

Copyright:

Available Formats

AHB5 PROTOCOL

The success or failure of the bus transfer.

DECODER AND MULTIPLEXER:

Slave Transfer Responses

During reset all slaves must ensure that HREADYOUT is HIGH.

You might also like