Hws-A e PDF

Download as pdf or txt
Download as pdf or txt
You are on page 1of 18

HWS-A SERIES Single Output 15W ~ 150W UNIT・

PC Board

Contents
● HWS-A/HD ☞ a_HWS-A_15 Page
● HWS-A/ME ☞ a_HWS-A_25 Page
● Block Diagram, Sequence Time Chart ☞ a_HWS-A_35 Page
● Instruction Manual ☞ a_HWS-A_37 Page

HWS-A

UL62368-1/ UL508/CSA C22.2 EN62368-1


CSA62368-1 No.107.1-01
HWS15A/A-150A/A(With cover)

15 - 150W standard :without cover HWS15A/A  HWS30A/A  HWS50A/A HWS80A/A HWS100A/A HWS150A/A


5
warranty
E
A
R
S

HWS-A

■ Features ■Model naming method


● Environmentally-friendly 〔HWS15A-150A〕
・Contributing to energy conservation of the HWS 15A - 24 / □
customer's equipment in a further high efficiency Series name Output power
Blank: Without cover(standard)
・Also improve efficiency at light load / A:With cover
・Reduction of no-load power
/ R :Remote ON/OFF control, withoout
● Easy to use cover
・Enlarge ambient temperature to ensure the load (HWS50A,80A,100A,150A only)
/ RA:Remote ON/OFF control, with cover
factor of 100% to 50 ℃ from 40 ℃ , the customer's (HWS50A,80A,100A,150A only)
equipment is up the degree of freedom of the / ADIN:DIN rail mountable
(with cover type only, from 5 to 48
mechanism design even at high temperatures VDC type)
(Ambient temperature -10℃ to +70℃) / B:Connector connection(JST)
(HWS50A,80A,100A,150A only,
● Safety and security 100A and 150A,12V-48V only)
・Reduce the maintenance frequency of your device
by a long life Nominal Output Voltage
  ex. 3 : 3.3V, 5 : 5V, 48 : 48V
・Double-sided board adopted inherited the
conventional model
・"Safety terminal" covering current flowing part
secures safety for users. "No screw-dropping"
design prevents from losing screws during
maintenance operation.
■ Conformity to RoHS Directive
■ Applications

■ Product Line up
15W 30W 50W 80W 100W 150W
Output
Voltage Output Output Output Output Output Output
MODEL MODEL MODEL MODEL MODEL MODEL
Current Current Current Current Current Current
3.3V 3A HWS15A-3 6A HWS30A-3 10A HWS50A-3 16A HWS80A-3 20A HWS100A-3 30A HWS150A-3

5V 3A HWS15A-5 6A HWS30A-5 10A HWS50A-5 16A HWS80A-5 20A HWS100A-5 30A HWS150A-5

12V 1.3A HWS15A-12 2.5A HWS30A-12 4.3A HWS50A-12 6.7A HWS80A-12 8.5A HWS100A-12 13A HWS150A-12

15V 1A HWS15A-15 2A HWS30A-15 3.5A HWS50A-15 5.4A HWS80A-15 7A HWS100A-15 10A HWS150A-15

24V 0.65A HWS15A-24 1.3A HWS30A-24 2.2A HWS50A-24 3.4A HWS80A-24 4.5A HWS100A-24 6.5A HWS150A-24

48V 0.33A HWS15A-48 0.65A HWS30A-48 1.1A HWS50A-48 1.7A HWS80A-48 2.1A HWS100A-48 3.3A HWS150A-48

ZHE
・All specifications are subject to change without notice.
a_HWS-A_1
HWS15A

UNIT・
HWS15
HWS15A SPECIFICATIONS (Read instruction manual carefully, before using the power supply unit.)
PC Board

MODEL
HWS15A-3 HWS15A-5 HWS15A-12 HWS15A-15 HWS15A-24 HWS15A-48
ITEMS/UNITS
Input Voltage Range (*2) V AC85 - 265 (47 - 63Hz) or DC120 - 370
Ef ciency(100VAC) (typ) (*1) % 70 77 80 81 82 82
Ef ciency(200VAC) (typ) (*1) % 71 79 83 84 85 82
Input
Input Current (100/200VAC) (typ) (*1) A 0.24/0.15 0.35/0.2
Inrush Current (100/200VAC) (typ) (*1)(*3) A 14/28 (Ta = 25℃ , Cold Start)
Leakage Current (*9) mA Less than 0.5 (0.2 (typ) at 100VAC / 0.4 (typ) at 230VAC)
Nominal Output Voltage VDC 3.3 5 12 15 24 48
Maximum Output Current A 3 3 1.3 1 0.65 0.33
Maximum Output Power W 10.0 15.0 15.6 15.0 15.6 15.8
Maximum Line Regulation (*5) mV 20 20 48 60 96 192
Maximum Load Regulation (*6) mV 40 40 96 120 150 240
Output
Temperature Coef cient Less than 0.02% /℃
Maximum Ripple & Noise(0≦Ta≦70℃ ) (*4) mV 120 120 150 150 150 200
Maximum Ripple & Noise(-10≦Ta<0℃ ) (*4) mV 160 160 180 180 180 240
Hold-up Time (typ) (*1) ms 20
Output Voltage Range VDC 2.97 - 3.96 4.0 - 6.0 9.6 - 14.4 12.0 - 18.0 19.2 - 28.8 38.4 - 52.8
3.15 ー 3.15 ー 1.36 ー 1.05 ー 0.68 ー 0.34 ー
HWS-A Over Current Protection (*7) A
Over Voltage Protection (*8) VDC 4.13 - 4.95 6.25 - 7.25 15.0 - 17.4 18.8 - 21.8 30.0 - 34.8 55.2 - 64.8
Remote Sensing -
Function Remote ON/OFF -
Parallel Operation -
Series Operation Possible
Line DIP Designed to meet SEMI-F47(200VAC Line only)
Operating Temperature (*10) ℃ -10 to +70 (-10 to +50℃ :100%, +60℃ :80%, +70℃ :60%)
Storage Temperature ℃ -30 to +85
Operating Humidity % RH 30 - 90(No Condensing)
Environment Storage Humidity % RH 10 - 95(No Condensing)
At no operating, 10-55Hz(Sweep for 1min)19.6m/s Constant, X,Y,Z 1hour each.
2
Vibration
2
Shock Less than 196.1m/s
Cooling Convection Cooling
Input - FG : 2kVAC (20mA), Input - Output : 3kVAC (20mA)
Withstand Voltage
Isolation Output - FG : 500VAC (20mA) for 1min
Isolation Resistance More than 100MΩ at 25℃ and 70%RH Output - FG : 500VDC
Approved by UL62368-1, CSA62368-1, EN62368-1, UL60950-1, CSA60950-1, EN60950-1.
Safety (Expire date of 60950-1: 20/12/2020) Designed to meet Den-an Appendix 8 at 100VAC only.
With cover type only: Approved by UL508, CSA C22.2 No.107.1-01.
Standards
PFHC Designed to meet IEC61000-3-2
Conducted Emission, Radiated Emission (*11) Designed to meet EN55011/EN55032-B, FCC-B, VCCI-B
Immunity (*11) Designed to meet IEC61000-6-2 IEC61000-4-2, -3, -4, -5, -6, -8, -11
Weight (typ) g 160 (With cover: 190)
Mechanical
Size (W x H x D) mm 26.5 x 82 x 80(Refer to Outline Drawing)

(*1) At 100VAC/200VAC, Ta=25℃ , nominal output voltage and maximum output power.
(*2) For cases where conformance to various safety specs (UL, CSA, EN) are required, to be described as 100 -
●Recommended EMC Filter
240VAC(50 - 60Hz).
(*3) Not applicable for the inrush current to Noise Filter for less than 0.2ms.
(*4) Measure with JEITA RC-9131B probe, Bandwidth of scope :100MHz.
For start up at low ambient temperature and low input voltage, output ripple noise might not meet speci cation.
However, speci cation can be met after one second.
(*5) 85 - 265VAC, constant load.
(*6) No load-Full load, constant input voltage.
(*7) Hiccup with automatic recovery. Avoid to operate at over load or short circuit condition. RSEN-2003D or RSEN-2003
(*8) OVP circuit will shut down output, manual reset (Re power on). Please refer to "TDK-Lambda
(*9) Measured by the each measuring method of UL, CSA, EN and Den-an (at 60Hz), Ta=25℃ . EMC Filters" catalog.
(*10) Output Derating
- Refer to Output Derating Curve.
- Load (%) is percent of maximum output power or maximum output current, do not exceed its derating
of maximum load.
(*11) The power supply is considered a component which will be installed into a nal equipment.
The nal equipment should be re-evaluated that it meets EMC directives.

・All specifications are subject to change without notice.


a_HWS-A_2
HWS15A

Outline Drawing
UNIT・
PC Board

【HWS15A】

(10.1) VOLTAGE ADJUSTMENT 2-M3 TAPPED HOLES


SCREW PENETRATION DEPTH MAX. 6mm
LED (GREEN)

5-M3.5

COVER
([/A]TYPE)

+V
7.3
-V

82±1
68±0.5
FG (67.5)

AC(L)
8.4

AC(N)
(17)

8
(14) (10) 62±0.5 8

26.5±1 19MAX 80±1 HWS-A


(WITHOUT COVER)
31.5±1
(WITH COVER)

2-M3 EMBOSSED, TAPPED AND COUNTERSUCK HOLES


SCREW PENETRATION DEPTH MAX. 6mm

NAME PLATE
17
15

Recommended Solderless Terminal


(5) 67±0.5 8
D(max) t(max) Qty(max)
(5.5)

6.8mm 0.8mm 2 pcs

[unit: mm]

Output Derating
●HWS15A ●HWS15A/A (WITH COVER) (OPTIONS/ADDIN INCLUDING)
120 120

100 100
90
80 80
LOAD (%)

LOAD (%)

60 60

40 40

20 20 MOUNTING (A)
MOUNTING (A), (B), (C), (D) MOUNTING (B), (C), (D)
0 0
-10 0 10 20 30 40 50 60 70 80 -10 0 10 20 30 40 50 60 70 80
Ta (°C) Ta (°C)

MOUNTING A
(STANDARD MOUNTING) MOUNTING B MOUNTING C MOUNTING D DON’T USE

・All specifications are subject to change without notice.


a_HWS-A_3
HWS30A

UNIT・
HWS30
HWS30
HWS30A SPECIFICATIONS (Read instruction manual carefully, before using the power supply unit.)
PC Board

MODEL HWS30A-3 HWS30A-5 HWS30A-12 HWS30A-15 HWS30A-24 HWS30A-48


ITEMS/UNITS
Input Voltage Range (*2) V AC85 - 265 (47 - 63Hz) or DC120 - 370
Ef ciency(100VAC) (typ) (*1) % 75 80 84 85 86 86
Ef ciency(200VAC) (typ) (*1) % 77 82 86 87 88 87
Input
Input Current (100/200VAC) (typ) (*1) A 0.5/0.3 0.65/0.4
Inrush Current (100/200VAC) (typ) (*1)(*3) A 14/28 (Ta = 25℃ , Cold Start)
Leakage Current (*9) mA Less than 0.5 (0.2 (typ) at 100VAC / 0.4 (typ) at 230VAC)
Nominal Output Voltage VDC 3.3 5 12 15 24 48
Maximum Output Current A 6 6 2.5 2 1.3 0.65
Maximum Output Power W 20.0 30.0 30.0 30.0 31.2 31.2
Maximum Line Regulation (*5) mV 20 20 48 60 96 192
Maximum Load Regulation (*6) mV 40 40 96 120 150 240
Output
Temperature Coef cient Less than 0.02% /℃
Maximum Ripple & Noise(0≦Ta≦70℃ ) (*4) mV 120 120 150 150 150 200
Maximum Ripple & Noise(-10≦Ta<0℃ ) (*4) mV 160 160 180 180 180 240
Hold-up Time (typ) (*1) ms 20
Output Voltage Range VDC 2.97 - 3.96 4.0 - 6.0 9.6 - 14.4 12.0 - 18.0 19.2 - 28.8 38.4 - 52.8
6.3 - 6.3 - 2.62 - 2.1 - 1.36 - 0.68 -
HWS-A Over Current Protection (*7) A
Over Voltage Protection (*8) VDC 4.13 - 4.95 6.25 - 7.25 15.0 - 17.4 18.8 - 21.8 30.0 - 34.8 55.2 - 64.8
Remote Sensing -
Function Remote ON/OFF -
Parallel Operation -
Series Operation Possible
Line DIP Designed to meet SEMI-F47(200VAC Line only)
Operating Temperature (*10) ℃ -10 to +70 (-10 to +50℃ :100%, +60℃ :60%, +70℃ :40%)
Storage Temperature ℃ -30 to +85
Operating Humidity % RH 30 - 90(No Condensing)
Environment Storage Humidity % RH 10 - 95(No Condensing)
At no operating, 10-55Hz(Sweep for 1min)19.6m/s Constant, X,Y,Z 1hour each.
2
Vibration
2
Shock Less than 196.1m/s
Cooling Convection Cooling
Input - FG : 2kVAC (20mA), Input - Output : 3kVAC (20mA)
Withstand Voltage
Isolation Output - FG : 500VAC (20mA) for 1min
Isolation Resistance More than 100MΩ at 25℃ and 70%RH Output - FG : 500VDC
Approved by UL62368-1, CSA62368-1, EN62368-1, UL60950-1, CSA60950-1, EN60950-1.
Safety (Expire date of 60950-1: 20/12/2020) Designed to meet Den-an Appendix 8 at 100VAC only.
With cover type only: Approved by UL508, CSA C22.2 No.107.1-01.
Standards
PFHC Designed to meet IEC61000-3-2
Conducted Emission, Radiated Emission (*11) Designed to meet EN55011/EN55032-B, FCC-B, VCCI-B
Immunity (*11) Designed to meet IEC61000-6-2 IEC61000-4-2, -3, -4, -5, -6, -8, -11
Weight (typ) g 200 (With cover: 240)
Mechanical
Size (W x H x D) mm 26.5 x 82 x 95 (Refer to Outline Drawing)
(*1) At 100VAC/200VAC, Ta=25℃ , nominal output voltage and maximum output power.
(*2) For cases where conformance to various safety specs (UL, CSA, EN) are required, to be described as 100 - ●Recommended EMC Filter
240VAC(50 - 60Hz).
(*3) Not applicable for the inrush current to Noise Filter for less than 0.2ms.
(*4) Measure with JEITA RC-9131B probe, Bandwidth of scope :100MHz.
For start up at low ambient temperature and low input voltage, output ripple noise might not meet
speci cation.
However, speci cation can be met after one second.
(*5) 85 - 265VAC, constant load.
(*6) No load-Full load, constant input voltage.
(*7) Hiccup with automatic recovery. Avoid to operate at over load or short circuit condition.
(*8) OVP circuit will shut down output, manual reset (Re power on).
RSEN-2003D or RSEN-2003
(*9) Measured by the each measuring method of UL, CSA, EN and Den-an (at 60Hz), Ta=25℃ . Please refer to "TDK-Lambda
(*10) Output Derating EMC Filters" catalog.
- Refer to Output Derating Curve.
- Load (%) is percent of maximum output power or maximum output current, do not exceed its derating
of maximum load.
(*11) The power supply is considered a component which will be installed into a nal equipment.
The nal equipment should be re-evaluated that it meets EMC directives.

・All specifications are subject to change without notice.


a_HWS-A_4
HWS30A

Outline Drawing
UNIT・
PC Board

【HWS30A】
(10.1) VOLTAGE ADJUSTMENT 2-M3 TAPPED HOLES
SCREW PENETRATION DEPTH MAX. 6mm

LED (GREEN)

5-M3.5
COVER
([/A]TYPE)

+V

68±0.5
7.3

82±1
-V
(67.5)

FG

AC(L)
8.4

AC(N)
(17)

8
(14) (10) 77±0.5 8

26.5±1 19MAX 95±1


HWS-A
(WITHOUT COVER)
31.5±1
2-M3 EMBOSSED, TAPPED AND COUNTERSUCK HOLES
(WITH COVER)
SCREW PENETRATION DEPTH MAX. 6mm

NAME PLATE
17
15

Recommended Solderless Terminal


D(max) t(max) Qty(max) (5) 82±0.5 8
(5.5)

6.8mm 0.8mm 2 pcs

[unit: mm]

Output Derating
●HWS30A ●HWS30A/A (WITH COVER) (OPTIONS/ADDIN INCLUDING)
120 120

100 100

80 80
LOAD (%)

LOAD (%)

60 60

40 40

20 20 MOUNTING (A)
MOUNTING (A), (B), (C), (D) MOUNTING (B), (C), (D)
0 0
-10 0 10 20 30 40 50 60 70 80 -10 0 10 20 30 40 50 60 70 80
Ta (°C) Ta (°C)

MOUNTING A
(STANDARD MOUNTING) MOUNTING B MOUNTING C MOUNTING D DON’T USE

・All specifications are subject to change without notice.


a_HWS-A_5
HWS50A

UNIT・
HWS50
HWS50A SPECIFICATIONS (Read instruction manual carefully, before using the power supply unit.)
PC Board

MODEL HWS50A-3 HWS50A-5 HWS50A-12 HWS50A-15 HWS50A-24 HWS50A-48


ITEMS/UNITS
Input Voltage Range (*2) V AC85 - 265 (47 - 63Hz) or DC120 - 370
Power Factor(100/200VAC) (typ) (*1) 0.96/0.85 0.97/0.91
Ef ciency(100VAC) (typ) (*1) % 76 82 83 83 84 84
Input Ef ciency(200VAC) (typ) (*1) % 78 84 85 86 87 86
Input Current (100/200VAC) (typ) (*1) A 0.45/0.25 0.65/0.35
Inrush Current (100/200VAC) (typ) (*1)(*3) A 14/28 (Ta = 25℃ , Cold Start)
Leakage Current (*9) mA Less than 0.5 (0.2 (typ) at 100VAC / 0.4 (typ) at 230VAC)
Nominal Output Voltage VDC 3.3 5 12 15 24 48
Maximum Output Current A 10 10 4.3 3.5 2.2 1.1
Maximum Output Power W 33.0 50.0 51.6 52.5 52.8 52.8
Maximum Line Regulation (*5) mV 20 20 48 60 96 192
Maximum Load Regulation (*6) mV 40 40 96 120 150 240
Output
Temperature Coef cient Less than 0.02% /℃
Maximum Ripple & Noise(0≦Ta≦70℃ ) (*4) mV 120 120 150 150 150 200
Maximum Ripple & Noise(-10≦Ta<0℃ ) (*4) mV 160 160 180 180 180 240
Hold-up Time (typ) (*1) ms 20

HWS-A Output Voltage Range VDC 2.97 - 3.96 4.0 - 6.0 9.6 - 14.4 12.0 - 18.0 19.2 - 28.8 38.4 - 52.8
Over Current Protection (*7) A 10.5 - 10.5 - 4.51 - 3.67 - 2.31 - 1.15 -
Over Voltage Protection (*8) VDC 4.13 - 4.95 6.25 - 7.25 15.0 - 17.4 18.8 - 21.8 30.0 - 34.8 55.2 - 64.8
Remote Sensing -
Function Remote ON/OFF - (/R Option: Output ON in the external voltage is applied)
Parallel Operation -
Series Operation Possible
Line DIP Designed to meet SEMI-F47(200VAC Line only)
Operating Temperature (*10) ℃ -10 to +70 (-10 to +50℃ :100%, +60℃ :70%, +70℃ :40%)
Storage Temperature ℃ -30 to +85
Operating Humidity % RH 30 - 90(No Condensing)
Environment Storage Humidity % RH 10 - 95(No Condensing)
At no operating, 10-55Hz(Sweep for 1min)19.6m/s Constant, X,Y,Z 1hour each.
2
Vibration
2
Shock Less than 196.1m/s
Cooling Convection Cooling
Input - FG : 2kVAC (20mA), Input - Output : 3kVAC (20mA)
Withstand Voltage
Isolation Output - FG : 500VAC (20mA) for 1min
Isolation Resistance More than 100MΩ at 25℃ and 70%RH Output - FG : 500VDC
Approved by UL62368-1, CSA62368-1, EN62368-1, UL60950-1, CSA60950-1, EN60950-1.
Safety (Expire date of 60950-1: 20/12/2020) Designed to meet Den-an Appendix 8 at 100VAC only.
With cover type only: Approved by UL508, CSA C22.2 No.107.1-01.

Standards PFHC Designed to meet IEC61000-3-2


Conducted Emission, Radiated Emission (*11) Designed to meet EN55011/EN55032-B, FCC-B, VCCI-B
Immunity (*11) Designed to meet IEC61000-6-2 IEC61000-4-2, -3, -4, -5, -6, -8, -11
Weight (typ) g 260 (With cover: 300)
Mechanical Size (W x H x D) mm 26.5 x 82 x 120 (Refer to Outline Drawing)
(*1) At 100VAC/200VAC, Ta=25℃ , nominal output voltage and maximum output power.
(*2) For cases where conformance to various safety specs (UL, CSA, EN) are required, to be described as 100 - ●Recommended EMC Filter
240VAC(50 - 60Hz).
(*3) Not applicable for the inrush current to Noise Filter for less than 0.2ms.
(*4) Measure with JEITA RC-9131B probe, Bandwidth of scope :100MHz.
(*5) 85 - 265VAC, constant load.
(*6) No load-Full load, constant input voltage.
(*7) Hiccup with automatic recovery. Avoid to operate at over load or short circuit condition.
(*8) OVP circuit will shut down output, manual reset (Re power on).
(*9) Measured by the each measuring method of UL, CSA, EN and Den-an (at 60Hz), Ta=25℃ .
(*10) Output Derating RSEN-2003D or RSEN-2003
- Refer to Output Derating Curve. Please refer to "TDK-Lambda
- Load (%) is percent of maximum output power or maximum output current, do not exceed its derating EMC Filters" catalog.
of maximum load.
(*11) The power supply is considered a component which will be installed into a nal equipment.
The nal equipment should be re-evaluated that it meets EMC directives.

・All specifications are subject to change without notice.


a_HWS-A_6
HWS50A

Outline Drawing
UNIT・
PC Board

【HWS50A】 VOLTAGE ADJUSTMENT REMOTE ON/OFF CONTROL CONNECTOR ([/R] TYPE)

(10.1) /B (OPTION)
(4.8) 2-M3 TAPPED HOLES 5MAX
LED (GREEN) SCREW PENETRATION DEPTH MAX. 6mm CONNECTOR
+R -R
5-M3.5 1 2

COVER CN51
([/A]TYPE) 4
+V 3
+V
2

68±0.5
-V

82±1
-V
7.3

(75.5)
(67.5)

FG 5 FG

AC(L) 3 AC(L)
8.4

AC(N) 1 AC(N)
CN1
(17)

8
(14) (15) 97±0.5 8

26.5±1 19MAX 120±1


(WITHOUT COVER)
2-M3 EMBOSSED, TAPPED AND COUNTERSUCK HOLES
31.5±1
SCREW PENETRATION DEPTH MAX. 6mm
(WITH COVER)

NAME PLATE

HWS-A
17
15

[unit: mm]
(5) 105±0.5 10
(5.5)

/B (Option) Use connector


Recommended Solderless Terminal PART DESCRIPTION PART NAME MANUFACT QTY
D(max) t(max) Qty(max) CONNECTOR INPUT SIDE(CN1) B3P5-VH(LF(
)SN) JST 1
6.8mm 0.8mm 2 pcs CONNECTOR OUTPUT SIDE(CN51) B4P-VH
(LF()SN) JST 1
※Output terminal, please use one pin per 5A below.
/R (Option)
Remote ON / OFF control connector (JST) /B (Option) Recommended connector (it is not affixed to the product)
PIN HEADER B2B-XH-AM PART DESCRIPTION PART NAME MANUFACT QTY
SOCKET HOUSING XHP-2 SOCKET HOUSING (CN1) VHR-5N JST 1
TERMINAL PINS BXH-001T-P0.6 or SXH-001T-P0.6 SOCKET HOUSING (CN51) VHR-4N JST 1
HAND CRIMRING TOOL YC-110R or YRS-110 TERMINAL PINS (CN1,CN51) BVH-21T-P1.1 or SVH-21T-P1.1 JST 7
※ Housing and terminal pin are not attached to the product. HAND CRIMRING TOOL: YC-160R (JST)

Output Derating
●HWS50A(Including options model/R, /B) ●HWS50A/A (WITH COVER) (Including options model/RA, /ADDIN)
120 MOUNTING (A) 120 MOUNTING (A)
MOUNTING (B), (D) MOUNTING (B), (D)
100 MOUNTING (C)
100 MOUNTING (A)

86
80 80
LOAD (%)

LOAD (%)

76
70 73
65
60 60
58 53
46
40 40
30 30
20 20

0 0
-10 0 10 20 30 40 45 50 60 70 80 -10 0 10 20 30 40 50 60 70 80
Ta (°C) Ta (°C)

MOUNTING A MOUNTING B
(STANDARD MOUNTING)
DON’T USE

MOUNTING C MOUNTING D

・All specifications are subject to change without notice.


a_HWS-A_7
HWS80A

UNIT・
HWS100
HWS80A SPECIFICATIONS (Read instruction manual carefully, before using the power supply unit.)
PC Board

MODEL HWS80A-3 HWS80A-5 HWS80A-12 HWS80A-15 HWS80A-24 HWS80A-48


ITEMS/UNITS
Input Voltage Range (*2) V AC85 - 265 (47 - 63Hz) or DC120 - 370
Power Factor(100/200VAC) (typ) (*1) 0.96/0.87 0.98/0.91
Ef ciency(100VAC) (typ) (*1) % 81 83 85 85 86 87
Input Ef ciency(200VAC) (typ) (*1) % 83 85 87 87 88 89
Input Current (100/200VAC) (typ) (*1) A 0.72/0.36 1.04/0.52
Inrush Current (100/200VAC) (typ) (*1)(*3) A 14/28 (Ta = 25℃ , Cold Start)
Leakage Current (*9) mA Less than 0.5 (0.2 (typ) at 100VAC / 0.4 (typ) at 230VAC)
Nominal Output Voltage VDC 3.3 5 12 15 24 48
Maximum Output Current A 16 16 6.7 5.4 3.4 1.7
Maximum Output Power W 52.8 80.0 80.4 81.0 81.6 81.6
Maximum Line Regulation (*5) mV 20 20 48 60 96 192
Maximum Load Regulation (*6) mV 40 40 96 120 150 240
Output
Temperature Coef cient Less than 0.02% /℃
Maximum Ripple & Noise(0≦Ta≦70℃ ) (*4) mV 120 120 150 150 150 200
Maximum Ripple & Noise(-10≦Ta<0℃ ) (*4) mV 160 160 180 180 180 240
Hold-up Time (typ) (*1) ms 20

HWS-A Output Voltage Range VDC 2.97 - 3.96 4.0 - 6.0 9.6 - 14.4 12.0 - 18.0 19.2 - 28.8 38.4 - 52.8
Over Current Protection (*7) A 16.8 - 16.8 - 7.04 - 5.67 - 3.57 - 1.79 -
Over Voltage Protection (*8) VDC 4.13 - 4.95 6.25 - 7.25 15.0 - 17.4 18.8 - 21.8 30.0 - 34.8 55.2 - 64.8
Remote Sensing Possible
Function Remote ON/OFF - (/R Option: Output ON in the external voltage is applied)
Parallel Operation -
Series Operation Possible
Line DIP Designed to meet SEMI-F47(200VAC Line only)
Operating Temperature (*10) ℃ -10 ~ +70(-10 ~ +50℃ :100%, +60℃ :80%, +70℃ :60%)
Storage Temperature ℃ -30 to +85
Operating Humidity % RH 30 - 90(No Condensing)
Environment Storage Humidity % RH 10 - 95(No Condensing)
At no operating, 10-55Hz(Sweep for 1min) 19.6m/s Constant, X,Y,Z 1hour each.
2
Vibration
2
Shock Less than 196.1m/s
Cooling Convection Cooling
Input - FG : 2kVAC (20mA), Input - Output : 3kVAC (20mA)
Withstand Voltage
Isolation Output - FG : 500VAC (20mA) for 1min
Isolation Resistance More than 100MΩ at 25℃ and 70%RH Output - FG : 500VDC
Approved by UL62368-1, CSA62368-1, EN62368-1, UL60950-1, CSA60950-1, EN60950-1.
Safety (Expire date of 60950-1: 20/12/2020) Designed to meet Den-an Appendix 8 at 100VAC only.
With cover type only: Approved by UL508, CSA C22.2 No.107.1-01.
Standards
PFHC Designed to meet IEC61000-3-2
Conducted Emission, Radiated Emission (*11) Designed to meet EN55011/EN55032-B, FCC-B, VCCI-B
Immunity (*11) Designed to meet IEC61000-6-2 IEC61000-4-2, -3, -4, -5, -6, -8, -11
Weight (typ) g 420 (With cover: 470)
Mechanical
Size (W x H x D) mm 28 x 82 x 160(Refer to Outline Drawing)

(*1) At 100VAC/200VAC, Ta=25℃ , nominal output voltage and maximum output power.
(*2) For cases where conformance to various safety specs (UL, CSA, EN) are required, to be described as 100 - ●Recommended EMC Filter
240VAC(50 - 60Hz).
(*3) Not applicable for the inrush current to Noise Filter for less than 0.2ms.
(*4) Measure with JEITA RC-9131B probe, Bandwidth of scope :100MHz.
(*5) 85 - 265VAC, constant load.
(*6) No load-Full load, constant input voltage.
(*7) Constant current limit and hiccup with automatic recovery.
Avoid to operate at over load or short circuit condition.
(*8) OVP circuit will shut down output, manual reset (Re power on).
RSEN-2003D or RSEN-2003
(*9) Measured by the each measuring method of UL, CSA, EN and Den-an (at 60Hz), Ta=25℃ .
(*10) Output Derating Please refer to "TDK-Lambda
- Refer to Output Derating Curve. EMC Filters" catalog.
- Load (%) is percent of maximum output power or maximum output current, do not exceed its derating
of maximum load.
(*11) The power supply is considered a component which will be installed into a nal equipment.
The nal equipment should be re-evaluated that it meets EMC directives.

・All specifications are subject to change without notice.


a_HWS-A_8
HWS80A

Outline Drawing
UNIT・
PC Board

【HWS80A】 REMOTE ON/OFF CONTROL CONNECTOR ([/R] TYPE)


/B (OPTION)
(10.1) VOLTAGE ADJUSTMENT
2-M3 TAPPED HOLES
LED (GREEN)
(10) 5MAX CONNECTOR
SCREW PENETRATION DEPTH MAX. 6mm

COVER 2 -R

7-M3.5 ([/A]TYPE) 1 +R

CN51

8.6
+S 6
5 +V
4
+V 3
-V
10
2

68±0.5
-V 1

82±1
9.2

(75)
-S
7.3

FG 5 FG
AC(L) 3 AC(L)
8.4

AC(N) 1 AC(N)
CN1
(9)

8
(14) (17) 135±0.5 8

28±1 19MAX 160±1


(WITHOUT COVER)
33±1 2-M3 EMBOSSED, TAPPED AND COUNTERSUCK HOLES
(WITH COVER) SCREW PENETRATION DEPTH MAX. 6mm

NAME PLATE
17
15.5

(15) 125±0.5 20
(5.5)

[unit: mm] HWS-A

Recommended Solderless Terminal


Terminal
D(max) t(max) Qty(max) /B (Option) Use connector
0.8mm 2 pcs PART DESCRIPTION PART NAME MANUFACT QTY
8.1mm
1.0mm 1 pcs CONNECTOR INPUT SIDE(CN1) (LF(
B3 P5 -VH )SN) JST 1
Others 6.8mm 0.8mm 2 pcs CONNECTOR OUTPUT SIDE(CN51) B4 P-VH(LF(
)SN) JST 1
※Output terminal, please use one pin per 5A below.
/R (Option)
Remote ON / OFF control connector (JST) /B (Option) Recommended connector (it is not affixed to the product)
PIN HEADER B2B-XH-AM PART DESCRIPTION PART NAME MANUFACT QTY
SOCKET HOUSING XHP-2 SOCKET HOUSING (CN1) VHR-5N JST 1
TERMINAL PINS BXH-001T-P0.6 or SXH-001T-P0.6 SOCKET HOUSING (CN51) VHR-6N JST 1
HAND CRIMRING TOOL YC-110R or YRS-110 TERMINAL PINS (CN1,CN51) BVH-21T-P1.1 or SVH-21T-P1.1 JST 9
※ Housing and terminal pin are not attached to the product. HAND CRIMRING TOOL: YC-160R (JST)

Output Derating

●HWS80A(Including options model/R, /B) ●HWS80A/A (WITH COVER) (Including options model/RA, /ADDIN)
120 MOUNTING (A) 120 MOUNTING (A)
MOUNTING (B) MOUNTING (B), (D)
100 100
MOUNTING (C), (D) MOUNTING (C)
90 90
86
80 80
LOAD (%)

LOAD (%)

70 70

60 60
50
40 40

20 20

0 0
-10 0 10 20 30 40 45 50 60 70 80 -10 0 10 20 30 40 45 50 60 70 80
Ta (°C) Ta (°C)

MOUNTING A MOUNTING B
(STANDARD MOUNTING)
DON’T USE

MOUNTING C MOUNTING D

・All specifications are subject to change without notice.


a_HWS-A_9
HWS100A

UNIT・
HWS100A SPECIFICATIONS (Read instruction manual carefully, before using the power supply unit.)
PC Board

MODEL HWS100A-3 HWS100A-5 HWS100A-12 HWS100A-15 HWS100A-24 HWS100A-48


ITEMS/UNITS
Input Voltage Range (*2) V AC85 - 265 (47 - 63Hz) or DC120 - 370
Power Factor(100/200VAC) (typ) (*1) 0.96/0.89 0.98/0.93
Ef ciency(100VAC) (typ) (*1) % 82 84 86 86 87 88
Input Ef ciency(200VAC) (typ) (*1) % 84 86 88 88 89 90
Input Current (100/200VAC) (typ) (*1) A 0.9/0.45 1.3/0.65
Inrush Current (100/200VAC) (typ) (*1)(*3) A 14/28 (Ta = 25℃ Cold Start)
Leakage Current (*9) mA Less than 0.5 (0.2 (typ) at 100VAC / 0.4 (typ) at 230VAC)
Nominal Output Voltage VDC 3.3 5 12 15 24 48
Maximum Output Current A 20 20 8.5 7 4.5 2.1
Maximum Output Power W 66.0 100.0 102.0 105.0 108.0 100.8
Maximum Line Regulation (*5) mV 20 20 48 60 96 192
Maximum Load Regulation (*6) mV 40 40 96 120 150 240
Output
Temperature Coef cient Less than 0.02% /℃
Maximum Ripple & Noise(0≦Ta≦70℃ ) (*4) mV 120 120 150 150 150 200
Maximum Ripple & Noise(-10≦Ta<0℃ ) (*4) mV 160 160 180 180 180 240
Hold-up Time (typ) (*1) ms 20

HWS-A Output Voltage Range VDC 2.97 - 3.96 4.0 - 6.0 9.6 - 14.4 12.0 - 18.0 19.2 - 28.8 38.4 - 52.8
Over Current Protection (*7) A 21.0 - 21.0 - 8.92 - 7.35 - 4.72 - 2.20 -
Over Voltage Protection (*8) VDC 4.13 - 4.95 6.25 - 7.25 15.0 - 17.4 18.8 - 21.8 30.0 - 34.8 55.2 - 64.8
Remote Sensing Possible
Function Remote ON/OFF - (/R Option: Output ON in the external voltage is applied)
Parallel Operation -
Series Operation Possible
Line DIP Designed to meet SEMI-F47(200VAC Line only)
Operating Temperature (*10) ℃ -10 to +70 (-10 to +50℃ :100%, +60℃ :65%, +70℃ :30%)
Storage Temperature ℃ -30 to +85
Operating Humidity % RH 30 - 90(No Condensing)
Environment Storage Humidity % RH 10 - 95(No Condensing)
At no operating, 10-55Hz(Sweep for 1min) 19.6m/s Constant, X,Y,Z 1hour each.
2
Vibration
2
Shock Less than 196.1m/s
Cooling Convection Cooling
Input - FG : 2kVAC (20mA), Input - Output : 3kVAC (20mA)
Withstand Voltage
Isolation Output - FG : 500VAC (20mA) for 1min
Isolation Resistance More than 100MΩ at 25℃ and 70%RH Output - FG : 500VDC
Approved by UL62368-1, CSA62368-1, EN62368-1, UL60950-1, CSA60950-1, EN60950-1.
Safety (Expire date of 60950-1: 20/12/2020) Designed to meet Den-an Appendix 8 at 100VAC only.
With cover type only: Approved by UL508, CSA C22.2 No.107.1-01.
Standards
PFHC Designed to meet IEC61000-3-2
Conducted Emission, Radiated Emission (*11) Designed to meet EN55011/EN55032-B, FCC-B, VCCI-B
Immunity (*11) Designed to meet IEC61000-6-2 IEC61000-4-2, -3, -4, -5, -6, -8, -11
Weight (typ) g 420 (With cover: 470)
Mechanical
Size (W x H x D) mm 28 x 82 x 160(Refer to Outline Drawing)
(*1) At 100VAC/200VAC, Ta=25℃ , nominal output voltage and maximum output power.
(*2) For cases where conformance to various safety specs (UL, CSA, EN) are required, to be described as 100 - ●Recommended EMC Filter
240VAC(50 - 60Hz).
(*3) Not applicable for the inrush current to Noise Filter for less than 0.2ms.
(*4) Measure with JEITA RC-9131B probe, Bandwidth of scope :100MHz.
(*5) 85 - 265VAC, constant load.
(*6) No load-Full load, constant input voltage.
(*7) Constant current limit and hiccup with automatic recovery.
Avoid to operate at over load or short circuit condition.
(*8) OVP circuit will shut down output, manual reset (Re power on).
RSEN-2003D or RSEN-2003
(*9) Measured by the each measuring method of UL, CSA, EN and Den-an (at 60Hz), Ta=25℃ .
(*10) Output Derating Please refer to "TDK-Lambda
- Refer to Output Derating Curve. EMC Filters" catalog.
- Load (%) is percent of maximum output power or maximum output current, do not exceed its derating
of maximum load.
(*11) The power supply is considered a component which will be installed into a nal equipment.
The nal equipment should be re-evaluated that it meets EMC directives.

・All specifications are subject to change without notice.


a_HWS-A_10
HWS100A

Outline Drawing UNIT・


PC Board

【HWS100A】 REMOTE ON/OFF CONTROL CONNECTOR ([/R] TYPE)


/B (OPTION)
VOLTAGE ADJUSTMENT
(10.1) 2-M3 TAPPED HOLES
LED (GREEN) (10)
SCREW PENETRATION DEPTH MAX. 6mm
5MAX CONNECTOR

COVER 2 -R

7-M3.5 ([/A]TYPE) 1 +R

CN51

8.6
+S 6
5 +V
4
+V 3
-V
10
2

68±0.5
-V 1

82±1
9.2

(75)
-S
7.3

FG 5 FG
AC(L) 3 AC(L)
8.4

AC(N) 1 AC(N)
CN1
(9)

8
(14) (17) 135±0.5 8

28±1 19MAX 160±1


(WITHOUT COVER)
33±1 2-M3 EMBOSSED, TAPPED AND COUNTERSUCK HOLES
(WITH COVER) SCREW PENETRATION DEPTH MAX. 6mm

NAME PLATE
17
15.5

(15) 125±0.5 20
(5.5)

[unit: mm] HWS-A

Recommended Solderless Terminal


Terminal
D(max) t(max) Qty(max) /B (Option) Use connector
0.8mm 2 pcs PART DESCRIPTION PART NAME MANUFACT QTY
8.1mm
1.0mm 1 pcs CONNECTOR INPUT SIDE(CN1) (LF(
B3 P5 -VH )SN) JST 1
Others 6.8mm 0.8mm 2 pcs CONNECTOR OUTPUT SIDE(CN51) B4 P-VH(LF(
)SN) JST 1
※Output terminal, please use one pin per 5A below.
/R (Option)
Remote ON / OFF control connector (JST) /B (Option) Recommended connector (it is not affixed to the product)
PIN HEADER B2B-XH-AM PART DESCRIPTION PART NAME MANUFACT QTY
SOCKET HOUSING XHP-2 SOCKET HOUSING (CN1) VHR-5N JST 1
TERMINAL PINS BXH-001T-P0.6 or SXH-001T-P0.6 SOCKET HOUSING (CN51) VHR-6N JST 1
HAND CRIMRING TOOL YC-110R or YRS-110 TERMINAL PINS (CN1,CN51) BVH-21T-P1.1 or SVH-21T-P1.1 JST 9
※ Housing and terminal pin are not attached to the product. HAND CRIMRING TOOL: YC-160R (JST)

Output Derating
●HWS100A(Including options model/R, /B) ●HWS100A/A (WITH COVER) (Including options model/RA, /ADDIN)
MOUNTING (A)
120 MOUNTING (A) 120
MOUNTING (B)
MOUNTING (B)
100 100 MOUNTING (C)
MOUNTING (C), (D) 92
MOUNTING (D)
80 80
LOAD (%)

LOAD (%)

65 65
60 60
42
40 40
37
30
20 20
10
0 0
-10 0 10 20 30 40 50 60 70 80 -10 0 10 20 30 35 40 50 60 70 80
Ta (°C) Ta (°C)

 Refer to dotted line for output derating curve, when input voltage range
is "85VAC≦Vin<90VAC" for the Mounting (A).

MOUNTING A MOUNTING B
(STANDARD MOUNTING)
DON’T USE

MOUNTING C MOUNTING D

・All specifications are subject to change without notice.


a_HWS-A_11
HWS150A

UNIT・
HWS150
HWS150A SPECIFICATIONS (Read instruction manual carefully, before using the power supply unit.)
PC Board

MODEL HWS150A-3 HWS150A-5 HWS150A-12 HWS150A-15 HWS150A-24 HWS150A-48


ITEMS/UNITS
Input Voltage Range (*2) V AC85 - 265 (47 - 63Hz) or DC120 - 370
Power Factor(100/200VAC) (typ) (*1) 0.96/0.89 0.98/0.93
Ef ciency(100VAC) (typ) (*1) % 82 85 85 86 88 89
Input Ef ciency(200VAC) (typ) (*1) % 84 87 88 89 90 91
Input Current (100/200VAC) (typ) (*1) A 1.3/0.65 1.9/0.95
Inrush Current (100/200VAC) (typ) (*1)(*3) A 14/28 (Ta = 25℃ , Cold Start)
Leakage Current (*9) mA Less than 0.5 (0.2 (typ) at 100VAC / 0.4 (typ) at 230VAC)
Nominal Output Voltage VDC 3.3 5 12 15 24 48
Maximum Output Current A 30 30 13 10 6.5 3.3
Maximum Output Power W 99.0 150.0 156.0 150.0 156.0 158.4
Maximum Line Regulation (*5) mV 20 20 48 60 96 192
Maximum Load Regulation (*6) mV 40 40 96 120 150 240
Output
Temperature Coef cient Less than 0.02% /℃
Maximum Ripple & Noise(0≦Ta≦70℃ ) (*4) mV 120 120 150 150 150 200
Maximum Ripple & Noise(-10≦Ta<0℃ ) (*4) mV 160 160 180 180 180 240
Hold-up Time (typ) (*1) ms 20

HWS-A Output Voltage Range VDC 2.97 - 3.96 4.0 - 6.0 9.6 - 14.4 12.0 - 18.0 19.2 - 28.8 38.4 - 52.8
Over Current Protection (*7) A 31.5 - 31.5 - 13.6 - 10.5 - 6.82 - 3.46 -
Over Voltage Protection (*8) VDC 4.13 - 4.95 6.25 - 7.25 15.0 - 17.4 18.8 - 21.8 30.0 - 34.8 55.2 - 64.8
Remote Sensing Possible
Function Remote ON/OFF - (/R Option: Output ON in the external voltage is applied)
Parallel Operation -
Series Operation Possible
Line DIP Designed to meet SEMI-F47(200VAC Line only)
Operating Temperature (*10) ℃ -10 to +70 (-10 to +50℃ :100%, +60℃ :60%, +70℃ :20%)
Storage Temperature ℃ -30 to +85
Operating Humidity % RH 30 - 90(No Condensing)
Environment Storage Humidity % RH 10 - 95(No Condensing)
At no operating, 10-55Hz(Sweep for 1min)19.6m/s Constant, X,Y,Z 1hour each.
2
Vibration
2
Shock Less than 196.1m/s
Cooling Convection Cooling
Input - FG : 2kVAC (20mA), Input - Output : 3kVAC (20mA)
Withstand Voltage
Isolation Output - FG : 500VAC (20mA) for 1min
Isolation Resistance More than 100MΩ at 25℃ and 70%RH Output - FG : 500VDC
Approved by UL62368-1, CSA62368-1, EN62368-1, UL60950-1, CSA60950-1, EN60950-1.
Safety (Expire date of 60950-1: 20/12/2020) Designed to meet Den-an Appendix 8 at 100VAC only.
With cover type only: Approved by UL508, CSA C22.2 No.107.1-01.
Standards
PFHC Designed to meet IEC61000-3-2
Conducted Emission, Radiated Emission (*11) Designed to meet EN55011/EN55032-B, FCC-B, VCCI-B
Immunity (*11) Designed to meet IEC61000-6-2 IEC61000-4-2, -3, -4, -5, -6, -8, -11
Weight (typ) g 470 (With cover: 520)
Mechanical
Size (W x H x D) mm 37 x 82 x 160(Refer to Outline Drawing)

(*1) At 100VAC/200VAC, Ta=25℃ , nominal output voltage and maximum output power.
(*2) For cases where conformance to various safety specs (UL, CSA, EN) are required, to be described as 100 - ●Recommended EMC Filter
240VAC(50 - 60Hz).
(*3) Not applicable for the inrush current to Noise Filter for less than 0.2ms.
(*4) Measure with JEITA RC-9131B probe, Bandwidth of scope :100MHz.
(*5) 85 - 265VAC, constant load.
(*6) No load-Full load, constant input voltage.
(*7) Constant current limit and hiccup with automatic recovery.
Avoid to operate at over load or short circuit condition.
(*8) OVP circuit will shut down output, manual reset (Re power on).
RSEN-2003D or RSEN-2003
(*9) Measured by the each measuring method of UL, CSA, EN and Den-an (at 60Hz), Ta=25℃ .
(*10) Output Derating Please refer to "TDK-Lambda
- Refer to Output Derating Curve. EMC Filters" catalog.
- Load (%) is percent of maximum output power or maximum output current, do not exceed its derating
of maximum load.
(*11) The power supply is considered a component which will be installed into a nal equipment.
The nal equipment should be re-evaluated that it meets EMC directives.

・All specifications are subject to change without notice.


a_HWS-A_12
HWS150A

Outline Drawing
UNIT・
PC Board

【HWS150A】 REMOTE ON/OFF CONTROL CONNECTOR ([/R] TYPE) /B (OPTION)


(10.7) VOLTAGE ADJUSTMENT 2-M3 TAPPED HOLES
CONNECTOR
(10) 3.5MAX
SCREW PENETRATION DEPTH MAX. 6mm
LED (GREEN)

7-M3.5 COVER 2 -R
([/A]TYPE) 1 +R

CN51

8.6
+S 6
5 +V
+V 4
3

10
2 -V

68±0.5
-V

82±1
9.2 1

(75)
-S
7.3

FG 5 FG

AC(L) 3 AC(L)
8.4

AC(N) 1 AC(N)
CN1
(9)

8
(14.6) (17) 135±0.5 8

37±1 19MAX 160±1


(WITHOUT COVER)
42±1
(WITH COVER)
2-M3 EMBOSSED, TAPPED AND COUNTERSUCK HOLES
SCREW PENETRATION DEPTH MAX. 6mm

NAME PLATE

HWS-A
17
18.5

(15) 131±0.5 14
(6.1)

[unit: mm]
Recommended Solderless Terminal
Terminal
D(max) t(max) Qty(max) /B (Option) Use connector
0.8mm 2 pcs PART DESCRIPTION PART NAME MANUFACT QTY
8.1mm
1.0mm 1 pcs CONNECTOR INPUT SIDE(CN1) (LF(
B3 P5 -VH )SN) JST 1
Others 6.8mm 0.8mm 2 pcs CONNECTOR OUTPUT SIDE(CN51) B6 P-VH(LF(
)SN) JST 1
※Output terminal, please use one pin per 5A below.
/R (Option)
Remote ON / OFF control connector (JST) /B (Option) Recommended connector (it is not affixed to the product)
PIN HEADER B2B-XH-AM PART DESCRIPTION PART NAME MANUFACT QTY
SOCKET HOUSING XHP-2 SOCKET HOUSING (CN1) VHR-5N JST 1
TERMINAL PINS BXH-001T-P0.6 or SXH-001T-P0.6 SOCKET HOUSING (CN51) VHR-6N JST 1
HAND CRIMRING TOOL YC-110R or YRS-110 TERMINAL PINS (CN1,CN51) BVH-21T-P1.1 or SVH-21T-P1.1 JST 9
※ Housing and terminal pin are not attached to the product. HAND CRIMRING TOOL: YC-160R (JST)

Output Derating
●HWS150A(Including options model/R, /B) ●HWS150A/A (WITH COVER) (Including options model/RA, /ADDIN)
MOUNTING (A)
120 120
MOUNTING (B), (C), (D)
100 100
90
80 80
LOAD (%)

LOAD (%)

60 60

40 MOUNTING (A) 40
35
MOUNTING (B)
20 20
MOUNTING (C), (D) 10
0 0
-10 0 10 20 30 40 50 60 70 80 -10 0 10 20 30 40 50 60 70 80
Ta (°C) Ta (°C)

 In the case of using at the input voltage range "85 VAC ≦ Vin <90VAC",
output derating will be dashed line. (Mounting direction(A) only)

MOUNTING A MOUNTING B
(STANDARD MOUNTING) DON’T USE

MOUNTING C MOUNTING D

・All specifications are subject to change without notice.


a_HWS-A_13
a_HWS-A_14
HWS-A

Block Diagram UNIT・


PC Board
【HWS15A, HWS30A】

Inrush Current
Limit Circuit

Switching Circuit

Rectifier & Filter


Rectifier Circuit

Filter Circuit
Line Filter
Input Output
85 -265VAC

OCP
Circuit

OVP Photo- OVP

Control Circuit
Circuit Coupler Sensing

Photo- Output
Coupler Sensing

【HWS50A】
Inrush Current Limit Circuit

Switching Circuit

Rectifier & Filter


Rectifier Circuit

PFHC Circuit

Filter Circuit
Line Filter

Input
85 -265VAC
Output HWS-A

OCP
Circuit

OVP Photo- OVP


Control Circuit

Control Circuit

Circuit Coupler Sensing

Photo- Output
Coupler Sensing

Photo- Remote ON/OFF


Coupler Control
※Option

【HWS80A - HWS150A】
Inrush Current Limit Circuit

Switching Circuit

Rectifier & Filter


Rectifier Circuit

PFHC Circuit

Filter Circuit
Line Filter

Input Output
85 -265VAC

OCP
Circuit

OVP Photo- OVP


Control Circuit

Control Circuit

Circuit Coupler Sensing

Photo- Output
Coupler Sensing

Photo- Remote ON/OFF


Coupler Control
※Option

● Fuse rating: ●Circuit topology, swtching frequency


HWS15A: 2A HWS15A-50A: Flyback topology 100kHz (fixed)
HWS30A-100A: 3.15A HWS80A-150A: Cascade forward topology 120kHz (fixed)
HWS150A: 5A PFHC circuit:active filter 65kHz (fixed)

・All specifications are subject to change without notice.


a_HWS-A_35
HWS-A

UNIT・
Sequence Time Chart
PC Board
【HWS15A, HWS30A】

Input Voltage

OVP Point(∗1)

Output Voltage

(∗1) OVP Point


3V : 125 - 150%
5 - 48V : 125 - 145%
INPUT ON

OVP ACT ON

INPUT OFF

INPUT ON

OCP ACT ON

OCP RESET

INPUT OFF
【HWS50A - HWS150A】

Input Voltage
OVP Point(∗1)

HWS-A
(∗1) OVP Point
Output Voltage 3V : 125 - 150%
5 - 48V : 125 - 145%

Remote ON/OFF
Control(∗2)

(∗2) +R & -R level


INPUT ON

REMOTE OFF

REMOTE ON

OVP ACT ON

INPUT OFF

INPUT ON

OCP ACT ON

OCP RESET

INPUT OFF

4.5V or higher : ON
0.8V or less: OFF

・All specifications are subject to change without notice.


a_HWS-A_36
HWS-A

HWS15A, 30A, 50A, 80A, 100A, 150A Instruction Manual UNIT・


PC Board

Be sure to read this instruction manual thoroughly before using this product. Pay attention to all cautions and
warnings before using this product.

HWS15A ~ 150A Instruction Manual 


https://product.tdk.com/info/en/documents/instruction_manual/hws-a_apl.pdf

HWS-A
取扱説明

・All specifications are subject to change without notice.


a_HWS-A_37
Catalog Usage Precautions
Please observe the following points when using this catalog for power supplies and related products of TDK-Lambda
Corporation (hereafter referred to simply as "our products"). Be sure to carefully read all precautions stated below before
beginning to use our products.

1.The contents of this catalog are subject to change without notice, for example related to product improvements and
other instances. Always check the latest information before deciding on a product.

2.Our products are designed and manufactured under the assumption that they will be used as integrated power
supplies for normal industrial applications. They are not designed and manufactured for use in high-safety
applications (applications requiring very high reliability and safety levels, where a reliability or safety problem could
directly involve the risk of serious injury or death). If the customer decides to use our products in a high-safety
application, appropriate fail-safe design features must be provided (such as incorporating protective circuitry and/or
protective equipment in the system, or incorporating redundancy in the system so that a single failure cannot lead to
instability). TDK-Lambda Corporation does not assume liability for any claims or damages either by the customer or
third parties arising from the use of our products for high-safety applications.

3.When designing equipment in which our products are to be used, as well as peripheral circuitry for such equipment,
always observe the "Product Usage Precautions" noted in this catalog and/or the product documentation and ensure
that maximum ratings, power supply voltage range, operation temperature range and other specifications are not
exceeded. TDK-Lambda Corporation does not assume liability for any claims or damages arising from the use of our
products in a way that exceeds specifications, or from a type of usage indicated as unsuitable for the respective
product in this catalog.

4.The operation outline and usage descriptions given in this catalog are examples. Before actual use of a product, all
external factors must be examined carefully in order to ensure appropriate circuit and implementation design.
TDK-Lambda Corporation does not assume liability for any claims or damages arising from indirect problems such as
EMI or mechanical effects from our products.

5.The technical information included in this catalog is intended only for the purpose of illustrating representative
operation or application of our products. It does not imply any guarantee or granting of license for intellectual
property rights or other rights held either by TDK-Lambda Corporation or third parties. TDK-Lambda Corporation does
not assume liability for any problems with third parties related to intellectual property rights arising from the use of our
products.
6.Products listed in this catalog may require export permission or authorization in compliance with the Foreign
Exchange and Foreign Trade Act.

7.The contents of this catalog may not be reproduced or copied without permission by TDK-Lambda Corporation.

8.For any inquiries regarding this catalog, please contact the Sales Department of TDK-Lambda Corporation.

Please see the Web of relevant companies for latest updates.


*1. Note that the contents of this catalog may be changed without prior warning. Be sure to read catalogs and instruction manuals for each product before using them. For accuracy purposes, please ask for
specifications, and check contents.
*2. All included company names, products names and service marks, etc., are the trademarks or registered trademarks of TDK, TDK-Lambda or their subsidiaries in Japan and other countries. Note that the registered
mark ® or TM are not used in this material, excluding one section.
*3. The TDK logo is the registered trademark of TDK Corporation.

https://www.tdk-lambda.com/en/ TDK-Lambda Corporation


Nihonbashi Takashimaya Mitsui Bldg.
2-5-1 Nihonbashi, Chuo-ku, Tokyo 103-6128, JAPAN

HWS-A_1905E

You might also like