Safety Data Sheet

SECTION 1 PRODUCT AND COMPANY IDENTIFICATION

OLOA 10501
Product Use: Lubricating oil additive
Company Identification
Chevron Oronite Company LLC
4800 Fournace Place
Bellaire, TX 77401
United States of America

Transportation Emergency Response

Asia: Chevron Emergency Information Centre +(1) 510-231-0623
Australia: 1 800 009 010
China: (+86) 138 113 09746
Europe: Oronite SA - Gonfreville Plant +33 2 35 25 55 00
North America: CHEMTREC (800) 424-9300 or (703) 527-3887
South America: Chevron Oronite Brasil Ltda (24 hours) 55 11 4478-1200
Health Emergency
USA: International collect calls accepted. (800) 231-0623 or (510) 231-0623
Product Information
SDS Requests: (877) 512-7200
Technical Information: (877) 512-7200

Oronite D-Tect®, OLOA®, OGA®, OFA®, ODA®, PARATONE®, and TFA® are registered trademarks of
the Chevron Oronite Company LLC.

SECTION 2 HAZARDS IDENTIFICATION

CLASSIFICATION: Chronic aquatic toxicant: Category 4.

Environmental Hazards: May cause long lasting harmful effects to aquatic life.

PRECAUTIONARY STATEMENTS:
Prevention: Avoid release to the environment.
Disposal: Dispose of contents/container in accordance with applicable local/regional/national/international
regulations.

HAZARDS NOT OTHERWISE CLASSIFIED: Not Applicable

_____________________________________________________________________

Revision Number: 1 1 of 9 OLOA 10501

SDS : 43569
Revision Date: February 03, 2017
 SECTION 3 COMPOSITION/ INFORMATION ON INGREDIENTS

COMPONENTS CAS NUMBER AMOUNT

01154100-5328P Trade secret 60 - 65 %weight
Highly refined mineral oil (C15 - C50) Mixture 35 - 40 %weight

Note that the chemical identity of some or all of the above components is considered confidential business
information and is being withheld as permitted by 29 CFR 1910.1200 and various State Right-To-Know
Laws.

SECTION 4 FIRST AID MEASURES

Description of first aid measures

Eye: No specific first aid measures are required. As a precaution, remove contact lenses, if worn, and
flush eyes with water. If heated material should splash into eyes, flush eyes immediately with fresh water
for 15 minutes while holding the eyelids open. Remove contact lenses, if worn. Get immediate medical
attention.
Skin: No specific first aid measures are required. As a precaution, remove clothing and shoes if
contaminated. To remove the material from skin, apply a waterless hand cleaner, mineral oil, or petroleum
jelly. Then wash with soap and water. Discard contaminated clothing and shoes or thoroughly clean before
reuse. If the hot material gets on skin, quickly cool in water. See a doctor for extensive burns. Do not try
to peel the solidified material from the skin, or use solvents or thinners to dissolve it. The use of vegetable
oil or mineral oil is recommended for removal of this material from the skin.
Ingestion: No specific first aid measures are required. Do not induce vomiting. As a precaution, get
medical advice.
Inhalation: No specific first aid measures are required. If exposed to excessive levels of material in the air,
move the exposed person to fresh air. Get medical attention if coughing or respiratory discomfort occurs.

Most important symptoms and effects, both acute and delayed

IMMEDIATE HEALTH EFFECTS
Eye: Not expected to cause prolonged or significant eye irritation. If this material is heated, thermal burns
may result from eye contact.
Skin: Contact with the skin is not expected to cause prolonged or significant irritation. Contact with the skin
is not expected to cause an allergic skin response. Not expected to be harmful to internal organs if
absorbed through the skin. If this material is heated, thermal burns may result from skin contact.
Ingestion: Not expected to be harmful if swallowed.
Inhalation: Not expected to be harmful if inhaled. Contains a petroleum-based mineral oil. May cause
respiratory irritation or other pulmonary effects following prolonged or repeated inhalation of oil mist at
airborne levels above the recommended mineral oil mist exposure limit. Symptoms of respiratory irritation
may include coughing and difficulty breathing.

DELAYED OR OTHER HEALTH EFFECTS: Not classified

_____________________________________________________________________

Revision Number: 1 2 of 9 OLOA 10501

SDS : 43569
Revision Date: February 03, 2017
Indication of any immediate medical attention and special treatment needed Not Applicable

SECTION 5 FIRE FIGHTING MEASURES

EXTINGUISHING MEDIA: Use water fog, foam, dry chemical or carbon dioxide (CO2) to extinguish
flames.

PROTECTION OF FIRE FIGHTERS:

Fire Fighting Instructions: This material will burn although it is not easily ignited. See Section 7 for proper
handling and storage. For fires involving this material, do not enter any enclosed or confined fire space
without proper protective equipment, including self-contained breathing apparatus.
Combustion Products: Highly dependent on combustion conditions. A complex mixture of airborne
solids, liquids, and gases including carbon monoxide, carbon dioxide, and unidentified organic compounds
will be evolved when this material undergoes combustion. Combustion may form oxides of: Sulfur,
Calcium.

SECTION 6 ACCIDENTAL RELEASE MEASURES

Protective Measures: Eliminate all sources of ignition in vicinity of spilled material.

Spill Management: Stop the source of the release if you can do it without risk. Contain release to prevent
further contamination of soil, surface water or groundwater. Clean up spill as soon as possible, observing
precautions in Exposure Controls/Personal Protection. Use appropriate techniques such as applying
non-combustible absorbent materials or pumping. Where feasible and appropriate, remove contaminated
soil. Place contaminated materials in disposable containers and dispose of in a manner consistent with
applicable regulations. If heated material is spilled, allow it to cool before proceeding with disposal
methods.
Reporting: Report spills to local authorities and/or the U.S. Coast Guard's National Response Center at
(800) 424-8802 as appropriate or required.

SECTION 7 HANDLING AND STORAGE

General Handling Information: The maximum handling temperature is 90°C. Avoid contaminating soil or
releasing this material into sewage and drainage systems and bodies of water.
Precautionary Measures: Unintended interactions can occur between additive components when they are
mixed. This mixing may occur within a pipe (e.g. following inadequate flushing between piping of
components) and can cause gelation. Users should test for potential effects of mixing prior to initiating use.
Avoid contact of heated material with eyes, skin, and clothing.
Static Hazard: Electrostatic charge may accumulate and create a hazardous condition when handling this
material. To minimize this hazard, bonding and grounding may be necessary but may not, by themselves,
be sufficient. Review all operations which have the potential of generating and accumulating an
electrostatic charge and/or a flammable atmosphere (including tank and container filling, splash filling, tank
cleaning, sampling, gauging, switch loading, filtering, mixing, agitation, and vacuum truck operations) and
use appropriate mitigating procedures.
Container Warnings: Container is not designed to contain pressure. Do not use pressure to empty
_____________________________________________________________________

Revision Number: 1 3 of 9 OLOA 10501

SDS : 43569
Revision Date: February 03, 2017
container or it may rupture with explosive force. Empty containers retain product residue (solid, liquid,
and/or vapor) and can be dangerous. Do not pressurize, cut, weld, braze, solder, drill, grind, or expose
such containers to heat, flame, sparks, static electricity, or other sources of ignition. They may explode and
cause injury or death. Empty containers should be completely drained, properly closed, and promptly
returned to a drum reconditioner or disposed of properly.

General Storage Information: The maximum storage temperature is 65°C.

SECTION 8 EXPOSURE CONTROLS/PERSONAL PROTECTION

GENERAL CONSIDERATIONS:
Consider the potential hazards of this material (see Section 2), applicable exposure limits, job activities,
and other substances in the work place when designing engineering controls and selecting personal
protective equipment. If engineering controls or work practices are not adequate to prevent exposure to
harmful levels of this material, the personal protective equipment listed below is recommended. The user
should read and understand all instructions and limitations supplied with the equipment since protection is
usually provided for a limited time or under certain circumstances.

ENGINEERING CONTROLS:
Use in a well-ventilated area.

PERSONAL PROTECTIVE EQUIPMENT

Eye/Face Protection: No special eye protection is normally required. Where splashing is possible, wear
safety glasses with side shields as a good safety practice. If this material is heated, wear chemical goggles
or safety glasses or a face shield.
Skin Protection: No special protective clothing is normally required. Where splashing is possible, select
protective clothing depending on operations conducted, physical requirements and other substances in the
workplace. Suggested materials for protective gloves include: Nitrile Rubber, Silver Shield, Viton. If this
material is heated, wear insulated clothing to prevent skin contact if engineering controls or work practices
are not adequate to prevent skin contact.
Respiratory Protection: No respiratory protection is normally required.
If user operations generate an oil mist, determine if airborne concentrations are below the occupational
exposure limit for mineral oil mist. If not, wear an approved respirator that provides adequate protection
from the measured concentrations of this material. For air-purifying respirators use a particulate cartridge.
Use a positive pressure air-supplying respirator in circumstances where air-purifying respirators may not
provide adequate protection.

Occupational Exposure Limits:

Component Agency TWA STEL Ceiling Notation

01154100-5328P Not Applicable -- -- -- --

Highly refined mineral oil (C15 - OSHA Z-1 5 mg/m3 -- -- --
C50)
Highly refined mineral oil (C15 - ACGIH 5 mg/m3 10 mg/m3 -- --

_____________________________________________________________________

Revision Number: 1 4 of 9 OLOA 10501

SDS : 43569
Revision Date: February 03, 2017
C50)

Consult local authorities for appropriate values.

SECTION 9 PHYSICAL AND CHEMICAL PROPERTIES

Attention: the data below are typical values and do not constitute a specification.

Color: Brown
Physical State: Liquid
Odor: Petroleum odor
Odor Threshold: No data available
pH: Not Applicable
Vapor Pressure: 0.0001 torr (Estimated) @ 20 °C (68 °F)
Vapor Density (Air = 1): No data available
Initial Boiling Point: No data available
Solubility: Insoluble in water.
Freezing Point: No data available
Melting Point: No data available
Density: 1.2180 kg/l @ 15°C (59°F)
Viscosity: 1250 cSt @ 40°C (104°F)
Coefficient of Therm. Expansion / °F: No data available
Evaporation Rate: No data available
Decomposition temperature: No data available
Octanol/Water Partition Coefficient: No data available

FLAMMABLE PROPERTIES:
Flammability (solid, gas): No Data Available
Flashpoint: (Pensky-Martens Closed Cup) 180 °C (356 °F) Minimum
Autoignition: No data available
Flammability (Explosive) Limits (% by volume in air): Lower: No data available Upper: No data
available

SECTION 10 STABILITY AND REACTIVITY

Reactivity: May react with strong acids or strong oxidizing agents, such as chlorates, nitrates, peroxides,
etc.
Chemical Stability: This material is considered stable under normal ambient and anticipated storage and
handling conditions of temperature and pressure.
Conditions to Avoid: Do not exceed handling and storage temperatures listed in MSDS Section 7
(Handling and Storage).
Incompatibility With Other Materials: Not applicable
Hazardous Decomposition Products: None known (None expected)
Hazardous Polymerization: Hazardous polymerization will not occur.

_____________________________________________________________________

Revision Number: 1 5 of 9 OLOA 10501

SDS : 43569
Revision Date: February 03, 2017
 SECTION 11 TOXICOLOGICAL INFORMATION

Information on toxicological effects

Serious Eye Damage/Irritation: The eye irritation hazard is based on data for a similar material.

Skin Corrosion/Irritation: The 24-72 hour EU skin irritation scores for erythema and edema, respectively, in
rabbits are: 0.3, 0.

Skin Sensitization: The skin sensitization hazard is based on data for a similar material.

Acute Dermal Toxicity: The acute dermal toxicity hazard is based on evaluation of data for similar
materials.

Acute Oral Toxicity: The acute oral toxicity hazard is based on evaluation of data for similar materials.

Acute Inhalation Toxicity: The acute inhalation toxicity hazard is based on evaluation of data for similar
materials.
Acute Toxicity Estimate: Not Determined

Germ Cell Mutagenicity: The hazard evaluation is based on data for components or a similar material.

Carcinogenicity: The hazard evaluation is based on data for components or a similar material.

Reproductive Toxicity: The hazard evaluation is based on data for components or a similar material.

Specific Target Organ Toxicity - Single Exposure: The hazard evaluation is based on data for components
or a similar material.

Specific Target Organ Toxicity - Repeated Exposure: The hazard evaluation is based on data for
components or a similar material.

ADDITIONAL TOXICOLOGY INFORMATION:

This product contains petroleum base oils which may be refined by various processes including severe
solvent extraction, severe hydrocracking, or severe hydrotreating. None of the oils requires a cancer
warning under the OSHA Hazard Communication Standard (29 CFR 1910.1200). These oils have not
been listed in the National Toxicology Program (NTP) Annual Report nor have they been classified by the
International Agency for Research on Cancer (IARC) as; carcinogenic to humans (Group 1), probably
carcinogenic to humans (Group 2A), or possibly carcinogenic to humans (Group 2B).
These oils have not been classified by the American Conference of Governmental Industrial Hygienists
(ACGIH) as: confirmed human carcinogen (A1), suspected human carcinogen (A2), or confirmed animal
carcinogen with unknown relevance to humans (A3).

SECTION 12 ECOLOGICAL INFORMATION

ECOTOXICITY

_____________________________________________________________________

Revision Number: 1 6 of 9 OLOA 10501

SDS : 43569
Revision Date: February 03, 2017
This material may cause long-term adverse effects in the aquatic environment.
The product has not been tested. The statement has been derived from products of a similar structure and
composition.

MOBILITY
No data available.

PERSISTENCE AND DEGRADABILITY

This material is not expected to be readily biodegradable. The biodegradability of this material is based on
an evaluation of data for the components or a similar material.
The product has not been tested. The statement has been derived from products of a similar structure and
composition.

POTENTIAL TO BIOACCUMULATE
Bioconcentration Factor: No data available.
Octanol/Water Partition Coefficient: No data available

SECTION 13 DISPOSAL CONSIDERATIONS

Use material for its intended purpose or recycle if possible. This material, if it must be discarded, may meet
the criteria of a hazardous waste as defined by international, country, or local laws and regulations.

SECTION 14 TRANSPORT INFORMATION

The description shown may not apply to all shipping situations. Consult 49CFR, or appropriate Dangerous
Goods Regulations, for additional description requirements (e.g., technical name) and mode-specific or
quantity-specific shipping requirements.

DOT Shipping Description: NOT REGULATED AS HAZARDOUS MATERIAL FOR TRANSPORTATION

UNDER 49 CFR

IMO/IMDG Shipping Description: NOT REGULATED AS DANGEROUS GOODS FOR TRANSPORT

UNDER THE IMDG CODE

ICAO/IATA Shipping Description: NOT REGULATED AS DANGEROUS GOODS FOR TRANSPORT

UNDER ICAO

Transport in bulk according to Annex II of MARPOL 73/78 and the IBC code: Not applicable

SECTION 15 REGULATORY INFORMATION

EPCRA 311/312 CATEGORIES: 1. Immediate (Acute) Health Effects: NO

2. Delayed (Chronic) Health Effects: NO
3. Fire Hazard: NO
_____________________________________________________________________

Revision Number: 1 7 of 9 OLOA 10501

SDS : 43569
Revision Date: February 03, 2017
 4. Sudden Release of Pressure Hazard: NO
5. Reactivity Hazard: NO

REGULATORY LISTS SEARCHED:

01-1=IARC Group 1 03=EPCRA 313
01-2A=IARC Group 2A 04=CA Proposition 65
01-2B=IARC Group 2B 05=MA RTK
02=NTP Carcinogen 06=NJ RTK
07=PA RTK

No components of this material were found on the regulatory lists above.

CHEMICAL INVENTORIES:
All components comply with the following chemical inventory requirements: AICS (Australia), DSL
(Canada), EINECS (European Union), ENCS (Japan), KECI (Korea), NZIoC (New Zealand), PICCS
(Philippines), TCSI (Taiwan), TSCA (United States).

One or more components has been notified but may not be listed in the following chemical inventories:
IECSC (China). Secondary notification may be required.

SECTION 16 OTHER INFORMATION

NFPA RATINGS: Health: 0 Flammability: 1 Reactivity: 0

HMIS RATINGS: Health: 0 Flammability: 1 Reactivity: 0

(0-Least, 1-Slight, 2-Moderate, 3-High, 4-Extreme, PPE:- Personal Protection Equipment Index
recommendation, *- Chronic Effect Indicator). These values are obtained using the guidelines or published
evaluations prepared by the National Fire Protection Association (NFPA) or the National Paint and Coating
Association (for HMIS ratings).

REVISION STATEMENT:
SECTION 03 - Composition information was modified.

Revision Date: February 03, 2017

ABBREVIATIONS THAT MAY HAVE BEEN USED IN THIS DOCUMENT:

TLV - Threshold Limit Value TWA - Time Weighted Average
STEL - Short-term Exposure Limit PEL - Permissible Exposure Limit
GHS - Globally Harmonized System CAS - Chemical Abstract Service Number
ACGIH - American Conference of Governmental IMO/IMDG - International Maritime Dangerous Goods
Industrial Hygienists Code
API - American Petroleum Institute SDS - Safety Data Sheet
HMIS - Hazardous Materials Information System NFPA - National Fire Protection Association (USA)

_____________________________________________________________________

Revision Number: 1 8 of 9 OLOA 10501

SDS : 43569
Revision Date: February 03, 2017
DOT - Department of Transportation (USA) NTP - National Toxicology Program (USA)
IARC - International Agency for Research on OSHA - Occupational Safety and Health Administration
Cancer
NCEL - New Chemical Exposure Limit EPA - Environmental Protection Agency
SCBA - Self-Contained Breathing Apparatus

Prepared according to the 29 CFR 1910.1200 (2012) by Chevron Energy Technology Company, 6001
Bollinger Canyon Road, San Ramon, CA 94583.

The above information is based on the data of which we are aware and is believed to be correct as of
the date hereof. Since this information may be applied under conditions beyond our control and with
which we may be unfamiliar and since data made available subsequent to the date hereof may
suggest modifications of the information, we do not assume any responsibility for the results of its use.
This information is furnished upon condition that the person receiving it shall make his own
determination of the suitability of the material for his particular purpose.

_____________________________________________________________________

Revision Number: 1 9 of 9 OLOA 10501

SDS : 43569
Revision Date: February 03, 2017