Experiment No:: Instrument No.-Nr - Date

EXPERIMENT NO: INSTRUMENT NO.
- NR_ DATE:
TITLE: DETERMINATION OF THE RADIUS OF CURVATURE OF THE CONVEX
SURFACE OF A LENS BY MEANS OF NEWTON’S RING
APPARATUS 1. Sodium lamp

2. Convex lens
3 Plano Convex lens
4. Travelling Microscope
5. Plane Glass plate
Eye
piece
Glass plate
Microscope
Source of
monochromatic
Light
Plano convex lens

Air film
Fig-1. Expeimental Set up for Newton’s ring
AIR FILM
Fig 2 : Formation of Newton’s ring

AIR FILM
Fig. 3 NEWTON’S RING
THEORY: When a monochromatic beam if light coming from an extended source is incident on a
combination of L and G as shown in fig. 1 a part of it is reflected from the lower surface of the lens
and a part, after refraction through the film between L and G is reflected back from the surface of the
Plate G. These two parts are in a condition to interfere and give rise to a system of alternate dark and
bright rings with O, the point of contact (between L and G) as centre.
If the angle of incidence of the rays which fall on G is  and  is the refractive index of the film
between L and G then the diameter Dn of the nth dark or bright ring is given by
D2n / 4 = nR / cos (for dark rings)
And D2n / 4 = {(2n + 1)/2 * (R) / (cos) (for bright rings)
Where  is the wavelength of the light used and R is the radius of curvature of the lower surface of
the lens L.
For normal incidence ( = 0) as in the arrangement shown in fig.-1 and with  = 1 i.c. with an air film
between L and G we have
D2n = 4nR / (for dark rings)
And D2n = 2(2n + 1)/R (for bright rings)

Knowing  and measuring the diameter of the nth dark or bright ring R, the radius of curvature of the
convex surface of the lens in contact with the plate G, may be determined.
But it is always found that due to deformation of the surface near the point of contact, a few rings
round the central dark spot are not circular. Further, due to presence of dust particles the central fringe
may not be dark. In order to eliminate difficulties arising out of these factors the following procedure
may be adopted for the determination of R.
If Dm+n and Dn be the diameters of the (m+n) th and nth dark or bright rings then,
D2m+n – D2n = 4mR (for the dark or bright rings).
The above relation indicates that R may be determined even without knowing the exact ring number
(m+n) or n.
Thus by measuring the diameters of any dark or bright rings by means of a microscope and counting
the number of dark or bright rings lying between them R may be determined.
EXPERIMENTAL PROCEDURE AND DATA TABLES:
1) Level the traveling microscope.
2) Adjust the positions of the Collimating Convex Lens and Plano Convex Lens (Newton’s
Apparatus) on the wooden platform to form the Newton’s Ring.
3) Place the crosswire of the eyepiece of the traveling microscope on the tangent position of
the 10th dark ring at the left position from the centre ring.
4) Take the scale reading on the horizontal scale of the traveling microscope.
5) By only using the tangent screw of the traveling microscope place the crosswire on the 8 th
dark ring and record the scale reading on the horizontal scale of the traveling
microscope.
6) Repeat the step (5) for 6th, 4th and 2nd dark rings.
7) Now place the crosswire of the eyepiece on the tangent position of the 2nd dark ring at the
right side from the centre ring.
8) Take the scale reading on the horizontal scale of the traveling microscope.
9) Repeat the step(7) and step( 8) for 4th ,6th ,8th and 10th dark rings at the right hand side .
10) Calculate diameter of the rings from Table 1.
TABLE 1. Measurement of the diameter of the rings :
READING OF THE MICROSCOPE

DIAMETER
LEFT RIGHT Dn
RING
NO. MAIN VERNIER TOTAL MAIN VERNIER TOTAL (Rl ˜ Rr)
SCALE SCALE (Rl) SCALE SCALE (Rr
(c.m.) (c.m.) (c.m.) (c.m.) (c.m.) (c.m.) (cm.)
10
2
TABLE 2:To draw the graph of diameter2 vs Ring No
RING NO. Dn (c.m.) Dn2 (cm2)
10
11) Use Table 2 to draw the graph between diameter2 vs Ring No. By using slope of the
graph calculate Radius of Curvature of the Plano Convex Lens.
Calculation of slope:
Mean wavelength of sodium light () = 5893 Å
Calculation of Radius of Curvature:
D2 m+n – D2n
R= ------------------------ =
4m
DISCUSSIONS :
DISCUSSIONS :
1. The plano-convex lens used for the formation of Newton’s rings should have a spherical
surface of large radius of curvature. This is necessary because the rings observer have then a
large diameter and hence the error in the measurement of their diameters will be minimum.
2. It may so happen that the rings seen ate not circular but elliptic. This is mainly due to unclean
surface of the lens and the plate. For this reason, the surfaces are to be cleaned before the
commencement of the experiment.
3. The centre of the ring systems, according to the theory, should be dark. Sometimes, the central
spot appears bright. The reason for this is that the thickness at the point of contact, instead of
being zero, has a small value.
4. A few rings near the central spot are rather indistinct and wide. These rings’ should not be
taken into consideration.
5. While moving the microscope right or left, the cross-wire should intersect the rings
tangentially.
BIBLIOGRAPHY
1. A Handbook of Advance Practical Physics by C.R. Dasgupta.
2. Optics by Ajay Ghatak.

Experiment No:: Instrument No.-Nr - Date

Uploaded by

Copyright:

Available Formats

Experiment No:: Instrument No.-Nr - Date

Uploaded by

Document Information

Original Title

Copyright

Available Formats

Share this document

Share or Embed Document

Sharing Options

Did you find this document useful?

Is this content inappropriate?

Copyright:

Available Formats

Experiment No:: Instrument No.-Nr - Date

Uploaded by

Copyright:

Available Formats

EXPERIMENT NO: INSTRUMENT NO.

APPARATUS 1. Sodium lamp

Plano convex lens

Fig-1. Expeimental Set up for Newton’s ring

Fig 2 : Formation of Newton’s ring

Fig. 3 NEWTON’S RING

D2n / 4 = nR / cos (for dark rings)

And D2n / 4 = {(2n + 1)/2 * (R) / (cos) (for bright rings)

D2n = 4nR / (for dark rings)

And D2n = 2(2n + 1)/R (for bright rings)

D2m+n – D2n = 4mR (for the dark or bright rings).

EXPERIMENTAL PROCEDURE AND DATA TABLES:

1) Level the traveling microscope.

10) Calculate diameter of the rings from Table 1.

TABLE 1. Measurement of the diameter of the rings :

READING OF THE MICROSCOPE

RING NO. Dn (c.m.) Dn2 (cm2)

graph calculate Radius of Curvature of the Plano Convex Lens.

Mean wavelength of sodium light () = 5893 Å

Calculation of Radius of Curvature:

1. A Handbook of Advance Practical Physics by C.R. Dasgupta.

2. Optics by Ajay Ghatak.

You might also like