Scribd Logo
Upload

Welcome to Scribd!

  • 91 views

    MML Commands

    Uploaded by

    sibi krishnan
    This document provides instructions for configuring BTS in 6 steps: 1) Create D-Channel links for O&M and TRX, 2) Create BCF, 3) Create BTS, 4) Create TRX, 5) Default power control parameters, and 6) Default handover control parameters. It also provides useful BSC commands for checking status, configuration, alarms and more.

    Copyright:

    © All Rights Reserved
    Download as PDF, TXT or read online from Scribd

    MML Commands

    Uploaded by

    sibi krishnan
    91 views5 pages
    This document provides instructions for configuring BTS in 6 steps: 1) Create D-Channel links for O&M and TRX, 2) Create BCF, 3) Create BTS, 4) Create TRX, 5) Default power control parameters, and 6) Default handover control parameters. It also provides useful BSC commands for checking status, configuration, alarms and more.

    Original Title

    MML-Commands

    Copyright

    © © All Rights Reserved

    Available Formats

    PDF, TXT or read online from Scribd

    Did you find this document useful?

    Is this content inappropriate?

    This document provides instructions for configuring BTS in 6 steps: 1) Create D-Channel links for O&M and TRX, 2) Create BCF, 3) Create BTS, 4) Create TRX, 5) Default power control parameters, and 6) Default handover control parameters. It also provides useful BSC commands for checking status, configuration, alarms and more.

    Copyright:

    © All Rights Reserved
    Download as PDF, TXT or read online from Scribd
    Download as pdf or txt
    91 views5 pages

    MML Commands

    Uploaded by

    sibi krishnan
    This document provides instructions for configuring BTS in 6 steps: 1) Create D-Channel links for O&M and TRX, 2) Create BCF, 3) Create BTS, 4) Create TRX, 5) Default power control parameters, and 6) Default handover control parameters. It also provides useful BSC commands for checking status, configuration, alarms and more.

    Copyright:

    © All Rights Reserved
    Download as PDF, TXT or read online from Scribd
    Download as pdf or txt
    You are on page 1of 5

    BTS Configuration

    1. Create and activate the D-Channel links for O&M and TRX

     Create O&M Link (Assume P202O is the O&M link ID)


    #ZDSE:P202O:BCSU,1:62,1:64,36-31:;
     Activate BCSU
    #ZDTC:P202O:WO;

     Create TRX Link (Assume P2021 is the TRX link ID)


    #ZDSE:p2021:BCSU,1:0,1:64,36-30:;
     Activate TRX
    #ZDTC:P2021:WO;

     Check the links status by executing below commands


    #ZDSB:NAME=P202O;
    #ZDSB:NAME=P2021;

    2. Create BCF

     Assume that BCF number is 202, DNAME is as created in the O&M link:P202O)
    #ZEFC:202,P:DNAME=P202O,::::;
     Check the status of the BCF
    #ZEEI:BCF=202:;

    3. Create BTS

     Assume BCF id is 202 and BCF Id is 202


    #ZEQC:BCF=202,BTS=202,:CI=3299,BAND=1800:NCC=0,BCC=0:MCC=520,MN
    C=18,LAC=26214:HOP=N,:GENA=Y,NSEI=1000,RAC=1,:;

    NOTE: The following contents can be available in lab support database


    CI, Band, MNC, MCC, LAC, NSEI, RAC

     Check the status of BTS


    #ZEEI:BTS=202;

    4. Create TRX

     Take the D-Channel name and BTS Id from step 1 to create TRX
    #ZERC:BTS=202,TRX=1:PREF=P,:FREQ=544,TSC=0,PCMTSC=36-
    1:DNAME=P2021:CH0=MBCCH,CH1=SDCCH,:;

    NOTE: FREQ can be available in the lab support data, PCMTSL ET36 time slot 1

    5. Default Power control parameters (Assume that BTS no. is 202)


    #ZEUC:BTS=202:;

    6. Default Handover control parameters (Assume that BTS no. is 202)


    #ZEHC:BTS=202:;

    Update the BTS software build


     Check the software build on 202 Id
    #ZEWO:202;
     List the BTS software builds
    #ZEWL;
     Attach the BTS software build to 202 Id
    #ZEWA:202:NW:CX5_ULTRA:;
    NOTE: CX5_ULTRA is one of the BTS software build
     Activate the software build to BTS
    #ZEWV:202:NW:;

    Useful commands

    1. Check the software packages and active packages on the BSC


    #ZWQO:CR;

    2. Check the running packages on the BSC


    #ZWQO:RUN;

    3. To enable EGPRS on BTS (Before executing this command lock the BTS)
    #ZEQV:BTS=202:EGENA=Y,;

    4. Lock BTS (Assume BTS no. is 202)


    #ZEQS:BTS=202:L:;

    5. Modify D-Channel working status


    #ZDTC:P2021:AD:;

    6. Check the D-Channel signalling link status


    ZDSB:NAME=P202%
    NOTE:’%’ takes any single character

    7. Delete O&M link (Delete all TRX, BTS, BCF before deleting the following link)
    #ZDSD:P202O:;

    8. Delete BTS (Assume that BTS no. is 202, Before executing this command lock the BTS)
    #ZEQD:BTS=202::;

    9. Delete BCF (Assume that BCF no.202, Before executing this command delete BTS)
    #ZEEI:BCF=202::;

    10. Unlock TRX (Assume that BTS no. is 202)


    #ZERS:BTS=202,TRX=1,:U:;

    11. Unlock BTS (Assume that BTS no. is 202)


    #ZEQS:BTS=202:U:;

    12. Adjust Power (Assume that BTS no. is 202)


    #ZEUG:BTS=202:PMIN=30,PMAX=30:;

    13. BSC Network information


    #ZEEL;

    14. List the status of UNITS


    #ZDTI;
    15. List the executed commands
    #ZIGO;

    16. Clearing the alarms for UNITS


    #ZUST;

    17. Creating DAP pool, this is needed if we are enabled EGPRS


    #ZESE:ID=1,CRCT=36-25&&-29,BCSU=0,PCU=4:;
    Attaching the DAP pool to TRX
    ZERM:BTS=202,TRX=1:DAP=1,;

    18. List O&M and Signalling D-Channel links for a particular ET number
    #ZDTI:::PCM=37,:;

    19. D-Channel telecom link set (Assume BTS id is 202)


    #ZERO:BTS=202,TRX=1:;

    20. List the units and computer identifier


    #ZUSI:COMP;

    21. Blocking SDCCH (BTS Id and TRX Id should be in hexadecimal number)


    #ZOS:*,<computer_id>,1B4,,,,,5996,,,XW<bts_id>,<trx_id>,<tsl_id>,7

    22. Deblock SDCCH


    ZOS:*,<computer_id>,1B4,,,,,9500,,,XW<bts_id>,<trx_id>,<tsl_id>

    23. Checking the SDCCH subchannel state information in the given TRXs
    #ZDDS:;
    #7 (NOTE: Define a character to be used for the extension)
    #Z7T:<bts_id,trx_id>

    24. Start FOXMEA service terminal extension


    #ZDDS:;
    #4 (NOTE: Define a character to be used for the extension)
    #ZLE:4,FOX_BXSX
    Useful BSC Commands

     General

    ZAHO Alarms currently on


    ZEOL BTS alarms
    ZUSI Unit states

     A-Interface

    ZNEL Signaling Link states


    ZNET Route and link set states
    ZNHI SCCP Subsystem states
    ZRCI Circuits / Circuits Groups
    ZDRI Synchronization
    ZQWI Service channel configuration
    ZNRI Signaling Point data
    ZWGO Output Transcoder PCM information
    ZWGF Fetch through connections from teanscoder

     Abis-Interface

    ZEEI Radio Network Configuration states


    ZEFO BCF state and parameters
    ZEQO BTS states and parameters
    ZERO TRX states and parameters
    ZEOL BCF alarms currently on
    ZDTI D-Channel states
    ZRCI Circuits / Circuits Groups
    ZDSB D-Channel parameters
    ZRBI Semipermanent connections

     BCF SW

    ZEWL Existing SW packages


    ZEWO SW configuration of BCF
    ZEWP Contents of SW packages

     BSC SW

    ZWQO:CR SW packages and active packages


    ZWQH SW package change history
    1. Useful MSC Commands

     General

    ZAHO Alarms currently on


    ZUSI Unit states

     A-Interface

    ZNEL Signaling Link states


    ZNET Route and link set states
    ZNHI SCCP Subsystem states
    ZRCI Circuits / Circuits Groups
    ZDRI Synchronization
    ZNRI Signaling Point data

     Circuits and D-Channels

    ZDTI D-Channel states


    ZRCI Circuits / Circuits Groups
    ZDSB D-Channel parameters

     MSC SW

    ZWQO:CR SW packages and active package


    ZWQH SW package charge history

     HLR

    ZMI_ Home subscriber handling


    ZMB_ Basic service handling

    You might also like