OTPC accessories kits

OTPCA, OTPCB, OTPCC, OTPCD,

OTPCE, OTPCF, OTPCG, OTPCH,
OTPCJ, OTPCSEA, OTPCSEB,
OTPCSEC

Feature codes

Following is an alpha-numeric listing of feature codes. Those identified as “NA” cannot be ordered as field installable
accessories. They must be selected on the original factory order.
Accessory kit part number Instruction sheet
A028-7 3-pole NA NA
A029-7 4-pole NA NA
A035-7 Application - utility-to-genset NA NA
A036-7 Application - utility-to-utility NA NA
A037-7 Application - genset-to-genset NA NA
A041-7 System – 3-phase, 2-wire or 3-wire NA NA
A042-7 System – 3-phase, 3-wire or 4-wire NA NA
A044-7 Frequency - 60 hertz NA NA
A045-7 Frequency - 50 hertz NA NA
A046-7 Listing UL 1008/CSA certification NA NA
A064-7 Listing - UL/NFPA 20 fire pump circuits NA NA
A077-7 Transfer mode – in-phase transition NA NA
A078-7 Transfer mode – delayed transition NA NA
A079-7 Transfer mode – closed NA NA
A080-7 Certification – seismic ATS NA NA
B001-7 Cabinet - type 1 NA NA
B002-7 Cabinet - type 3R NA NA
B003-7 Cabinet - type 4 NA NA
B004-7 Construction - open NA NA
B010-7 Cabinet - type 12 NA NA
B025-7 Cabinet - type 4x stainless NA NA
C023-7 Switch control - level 1 NA NA
C024-7 Switch control - level 2 NA NA
D009-7 Meters - bar graph display NA NA

©2010 Cummins Power Generation Inc. All rights reserved. Cummins Power Generation, Cummins and PowerCommand are registered
trademarks of Cummins Inc. “Our energy working for you.” and InPower are trademarks of Cummins Power Generation. Other company, product
or service names may be trademarks or service marks of others. Specifications are subject to change without notice.
AC-167f (1/10) Page 1 of 8
Battery chargers
Battery chargers may be mounted on the transfer switch, for use in charging the genset starting and control batteries.
See specification sheets for battery charger design and specification information.
Accessory kit part number Instruction sheet
Battery charger-2 amp, 12/24 VDC out
K001-7
120 volt 0300-6026-09 C687
208 volt/190 volt 0300-6026-10 C687
240 volt/220 volt 0300-6026-11 C687
380 volt 0300-6026-13 C687
416 volt/440 volt 0300-6026-14 C687
480 volt 0300-6026-15 C687
600 volt 0300-6026-16 C687
KB59-7 Battery charger - 15 amp, 12 VDC, 50/60 Hz
KB60-7 Battery charger - 12 amp, 24 VDC, 50/60 Hz
120 volt 0300-5878-13 C672
208 volt/190 volt 0300-5878-13 C672
240 volt/220 volt 0300-5878-13 C672
277 volt 0300-5878-14 C672
380 volt 0300-5878-15 C672
416 volt/440 volt 0300-5878-16 C672
480 volt 0300-5878-17 C672
600 volt 0300-5878-18 C672
Temperature sensor kit 0541-0918 G573

Auxiliary relays
Provides three sets of double throw contacts for customer use.
Accessory kit part number Instruction sheet
L101-7 Auxiliary relay - 24 VDC - 2 N/O and 2 N/C contacts* 0300-3503* C274

L102-7 Auxiliary relay - 24 VDC - 2 N/O and 2 N/C contacts 0300-3503* C274
emergency position*
L103-7 Auxiliary relay - 24 VDC - 2 N/O and 2 N/C contacts 0300-3503* C274
normal position*
L201-7 Auxiliary relay - 12 VDC - 2 N/O and 2 N/C contacts* 0300-3502* C274

L202-7 Auxiliary relay - 12 VDC - 2 N/O and 2 N/C contacts 0300-3502* C274
emergency position*
L203-7 Auxiliary relay - 12 VDC - 2 N/O and 2 N/C contacts 0300-3502* C274
normal position*

* Accessory mounting plate 0319-3943-01 (available through parts) is required to mount this kit. If your transfer switch already has one of the
features designated by a "*" this mounting plate is already there. Also, 1600 amp and above switches have this plate as standard.

Our energy working for you.™

www.cumminspower.com
©2010 Cummins Power Generation Inc. All rights reserved. Cummins Power Generation, Cummins and PowerCommand are registered
trademarks of Cummins Inc. “Our energy working for you.” and InPower are trademarks of Cummins Power Generation. Other company, product
or service names may be trademarks or service marks of others. Specifications are subject to change without notice.
AC-167f (1/10) Page 2 of 8
Terminal block
30 point terminal block to mount inside cabinet for customer select use.
Accessory kit part number Instruction sheet
M003-7 Terminal block - 30 points 0332-3302* C458

Load shed from emergency

Kit allows modification of the transfer switch to accept a remote signal to switch the transfer switch from emergency
position to neutral position.
Accessory kit part number Instruction sheet
Load shed - from emergency* (requires M023-7
M007-7
40 - 600 amp
- 120 - 480 VAC 0541-0655* C606
- 600 VAC 0541-0656* C606
800 - 1000 amp
- 120 - 600 VAC 0541-0656* C606
1200 - 4000 amp
- 120 - 600 VAC NA NA

Security key - front panel

Front panel access can be locked out using this option - prevents unauthorized transfers or testing and unauthorized
adjustments via the digital display.
Accessory kit part number Instruction sheet
M017-7 Security-front panel 0300-5444 C602

Digital display
The digital display provides a convenient method for monitoring load power conditions, adjusting transfers switch
parameters, monitoring PowerCommand® network status, or reviewing transfer switch events. Password protection
limits access to adjustments to authorized personnel. The digital display comes standard with the level 2
PowerCommand microprocessor control and optional with the level 1 control.
Accessory kit part number Instruction sheet
M018-7 Display-digital NA NA

* Accessory mounting plate 0319-3943-01 (available through parts) is required to mount this kit. If your transfer switch already has one of the
features designated by a "*" this mounting plate is already there. Also, 1600 amp and above switches have this plate as standard.

Our energy working for you.™

www.cumminspower.com
©2010 Cummins Power Generation Inc. All rights reserved. Cummins Power Generation, Cummins and PowerCommand are registered
trademarks of Cummins Inc. “Our energy working for you.” and InPower are trademarks of Cummins Power Generation. Other company, product
or service names may be trademarks or service marks of others. Specifications are subject to change without notice.
AC-167f (1/10) Page 3 of 8
Monitoring - load
Measures load phase and neutral, current, power factor, real power (kW) and apparent power (kVA). Warns of
excessive neutral current resulting from unbalanced or nonlinear loads.
Accessory kit part number Instruction sheet
Monitoring – load (1-phase)
M022-7
40 amp 0541-0619 C615
70 amp 0541-0620 C615
125 amp 0541-0621 C615
150 amp 0541-0622 C615
225 amp 0541-0623 C615
260 amp 0541-0624 C615
300 amp 0541-0625 C615
400 amp 0541-0626 C615
600 amp 0541-0627 C615
800 amp 0541-0628 C615
1000 amp 0541-0629 C615
1200 amp 0541-0630 C615
1600 amp
- 3-pole 0541-0633 C615
- 4-pole 0541-0634 C615
2000 amp
- 3-pole 0541-0631 C615
- 4-pole 0541-0635 C615
3000 amp
- 3-pole 0541-0632 C615
- 4-pole 0541-0636 C615
4000 amp NA NA
Monitoring – load (3-phase)
40 amp 0541-0637 C615
70 amp 0541-0638 C615
125 amp 0541-0639 C615
150 amp 0541-0640 C615
225 amp 0541-0641 C615
260 amp 0541-0642 C615
300 amp 0541-0643 C615
400 amp 0541-0644 C615
600 amp 0541-0645 C615
800 amp 0541-0646 C615
1000 amp 0541-0647 C615
1200 amp 0541-0648 C615
1600 amp
- 3-pole 0541-0649 C615
- 4-pole 0541-0652 C615
2000 amp
- 3-pole 0541-0650 C615
- 4-pole 0541-0653 C615
3000 amp
- 3-pole 0541-0651 C615
- 4-pole 0541-0654 C615
4000 amp NA NA

Our energy working for you.™

www.cumminspower.com
©2010 Cummins Power Generation Inc. All rights reserved. Cummins Power Generation, Cummins and PowerCommand are registered
trademarks of Cummins Inc. “Our energy working for you.” and InPower are trademarks of Cummins Power Generation. Other company, product
or service names may be trademarks or service marks of others. Specifications are subject to change without notice.
AC-167f (1/10) Page 4 of 8
Module - relay signal
Provides an adjustable transfer, pending time delay of 0 to 60 seconds and normal and emergency status signals, to
prevent interruption of power during elevator operation. Relay outputs include: Source 1 connected and available,
source 2 connected and available, not in auto, test/exercise active and pending transfer (elevator signal).
Accessory kit part number Instruction sheet
M023-7 Module - relay signal* 40-4000 amp 0300-5443* C601

Note: For use with all OTPC 40-1200 amp transfer switches, and all OTPC 1600-4000 amp transfer switches with B001-7 and B004-7 cabinets
only. Not for use with OTPC 1600-4000 amp transfer switches with B002-7, B003-7, B010-7 or B025 -7 cabinets

Network communication module

The module provides an interface to the PowerCommand FTT-10 network (LonWorks) and a load sequencer feature that
sequences other (network) devices in a timed fashion.
Accessory kit part Instruction sheet
Network communications module (NCM)(FTT)-
M031-7
40-1000 amp 0541-0812* C632
1200-4000 amp 0541-0868* C632

Mechanical lugs - cable

Accessory kit part number Instruction sheet
Mechanical lugs – cable (1600 - 3000 amp)
N008-7
3-pole
- 1600 - 2000 amp (8) 1/0 - 750 MCM 0332-3030 C334
- 3000 amp (8) #2 - 600 MCM 0332-3032 C334
- 4000 amp NA NA
4-pole
- 1600 - 2000 amp (8) 1/0 - 750 MCM 0332-3031 C334
- 3000 amp (8) #2 - 600 MCM 0332-3033 C334
- 4000 amp NA NA

Power connection-bus stubs

The transfer switch is equipped with bus stubs for bolted connection of customer supplied bussing. Stubs are sized for
full rated switch current. Bus stubs are available with "open construction" cabinet option only.
Accessory kit part number Instruction sheet
N009-7 Power connection - bus stubs NA NA

Harness - extension
Provides a harness to extend the distance between the control panel and the transfer switch up to 4 feet.
Accessory kit part number Instruction sheet
N013-7 Harness - extension, 4 ft, open construction units only 0338-2913-01 NA

Terminal block - retransfer inhibit

Retransfer inhibit terminal block connections inhibit retransfer to the utility or preferred source. Connecting the terminals
with a field installed jumper or switch inhibits retransfer. The override button on the front panel display overrides the
inhibit and initiates instant retransfer. Removing the connection enables the retransfer time delay and subsequent
retransfer.
Accessory kit part number Instruction sheet
N020-7 Terminal block-retransfer inhibit* 0300-5436* C597

* Accessory mounting plate 0319-3943-01 (available through parts) is required to mount this kit. If your transfer switch already has one of the
features designated by a "*" this mounting plate is already there. Also, 1600 amp and above switches have this plate as standard.

Our energy working for you.™

www.cumminspower.com
©2010 Cummins Power Generation Inc. All rights reserved. Cummins Power Generation, Cummins and PowerCommand are registered
trademarks of Cummins Inc. “Our energy working for you.” and InPower are trademarks of Cummins Power Generation. Other company, product
or service names may be trademarks or service marks of others. Specifications are subject to change without notice.
AC-167f (1/10) Page 5 of 8
Actuator - voltage conversion kits
These kits are for field conversion of the operating voltage of the transfer switch. Each kit is designed for use on any
voltage transfer switch.
Note: If the transfer switch being modified includes AC metering, a metering conversion kit will be required to complete the conversion
process. If a battery charger is included in the transfer switch, it also must be replaced.
Accessory kit part number Instruction sheet
Voltage - 120 VAC
R020-7
40 - 125 amp 0541-0690** C620
150 - 260 amp 0541-0695 C620
300 - 600 amp 0541-0700 C620
800 - 1000 amp 0541-0706 C620
1200 amp NA NA
1600 - 3000 amp NA NA
4000 amp NA NA
R021-7 Voltage - 208 VAC
40 - 125 amp 0541-0692** C620
150 - 260 amp 0541-0697 C620
300 - 600 amp 0541-0702 C620
800 - 1000 amp 0541-0708 C620
1200 amp 0300-4387*$ C445
1600 - 3000 amp 0300-4390*$ C445
4000 amp NA NA
R022-7 Voltage - 220 VAC
40 - 125 amp 0541-0692** C620
150 - 260 amp 0541-0697 C620
300 - 600 amp 0541-0703 C620
800 - 1000 amp 0541-0709 C620
1200 amp 0300-4387*$ C445
1600 - 3000 amp 0300-4390*$ C445
4000 amp NA NA
R023-7 Voltage - 240 VAC
40 - 125 amp 0541-0692** C620
150 - 260 amp 0541-0697 C620
300 - 600 amp 0541-0703 C620
800 - 1000 amp 0541-0709 C620
1200 amp 0300-4387*$ C445
1600 - 3000 amp 0300-4390*$ C445
4000 amp NA NA
R024-7 Voltage - 380 VAC
40 - 125 amp 0541-0693** C620
150 - 260 amp 0541-0698 C620
300 - 600 amp 0541-0704 C620
800 - 1000 amp 0541-0710 C620
1200 amp 0300-4388*$ C445
1600 - 3000 amp 0300-4391*$ C445
4000 amp NA NA
R025-7 Voltage - 416 VAC
40 - 125 amp 0541-0693** C620
150 - 260 amp 0541-0698 C620
300 - 600 amp 0541-0704 C620
800 - 1000 amp 0541-0710 C620
1200 amp 0300-4388*$ C445
1600 - 3000 amp 0300-4391*$ C445
4000 amp NA NA

Our energy working for you.™

www.cumminspower.com
©2010 Cummins Power Generation Inc. All rights reserved. Cummins Power Generation, Cummins and PowerCommand are registered
trademarks of Cummins Inc. “Our energy working for you.” and InPower are trademarks of Cummins Power Generation. Other company, product
or service names may be trademarks or service marks of others. Specifications are subject to change without notice.
AC-167f (1/10) Page 6 of 8
Actuator - voltage conversion kits (continued)
Accessory kit part number Instruction sheet
R026-7 Voltage - 480 VAC
40 - 125 amp 0541-0694** C620
150 - 260 amp 0541-0699 C620
300 - 600 amp 0541-0705 C620
800 - 1000 amp 0541-0711 C620
1200 amp 0300-4389*$ C445
1600 - 3000 amp 0300-4392*$ C445
4000 amp NA NA
R027-7 Voltage - 600 VAC
40 - 125 amp NA NA
150 - 260 amp NA NA
300 - 600 amp NA NA
800 - 1000 amp NA NA
1200 amp NA NA
1600 - 3000 amp NA NA
4000 amp NA NA
R035-7 Voltage - 440 VAC
40 - 125 amp 0541-0694** C620
150 - 260 amp 0541-0699 C620
300 - 600 amp 0541-0705 C620
800 - 1000 amp 0541-0711 C620
1200 amp 0300-4389*$ C445
1600 - 3000 amp 0300-4392*$ C445
4000 amp NA NA
R038-7 Voltage - 190 VAC
40 - 125 amp 0541-0691** C620
150 - 260 amp 0541-0696 C620
300 - 600 amp 0541-0701 C620
800 - 1000 amp 0541-0707 C620
1200 amp NA NA
1600 - 3000 amp NA NA
4000 amp NA NA
* Voltage conversion designed for closed and delayed transition switches only. Not for use with in-phase transition switches.
** These kits are to be used with 3 pole switches only. If you have a 40-70-125 4 pole, please use the kits that correspond to 150-225-260.
$ Order components through parts in Memphis.

Literature list
Literature list Accessory kit part number Instruction sheet
40 – 1000 amp 0999-0024 Std NA
1200 – 4000 amp 0998-0081 Std NA
1200 – 4000 amp 0998-0081-01 Seismic NA

Three wire start (TWS)

Three wire start (TWS) (See AC-145) Accessory kit part number Instruction sheet
120 VAC/12 VDC 0300-2860-01 NA
240 VAC/12 VDC 0300-2860-03 NA

Our energy working for you.™

www.cumminspower.com
©2010 Cummins Power Generation Inc. All rights reserved. Cummins Power Generation, Cummins and PowerCommand are registered
trademarks of Cummins Inc. “Our energy working for you.” and InPower are trademarks of Cummins Power Generation. Other company, product
or service names may be trademarks or service marks of others. Specifications are subject to change without notice.
AC-167f (1/10) Page 7 of 8
Service tools
Service tools (InPower) - contact service training

Certification

ISO9001 - This product was designed

and manufactured in facilities certified to
ISO9001.

Americas Europe, CIS, Middle East and Africa Asia Pacific

1400 73rd Avenue N.E. Manston Park Columbus Ave. 10 Toh Guan Road #07-01
Minneapolis, MN 55432 USA Manston Ramsgate TT International Tradepark
Phone: 763 574 5000 Kent CT 12 5BF United Kingdom Singapore 608838
Fax: 763 574 5298 Phone 44 1843 255000 Phone 65 6417 2388
Fax 44 1843 255902 Fax 65 6417 2399

Warning: Back feed to a utility system can cause electrocution and/or property damage. Do not connect generator sets to any building
electrical system except through an approved device or after building main switch is open.
Warning: For professional use only. Must be installed by a qualified service technician. Improper installation presents hazards of electrical
shock and improper operation, resulting in severe personal injury and/or property damage.

Our energy working for you.™

www.cumminspower.com
©2010 Cummins Power Generation Inc. All rights reserved. Cummins Power Generation, Cummins and PowerCommand are registered
trademarks of Cummins Inc. “Our energy working for you.” and InPower are trademarks of Cummins Power Generation. Other company, product
or service names may be trademarks or service marks of others. Specifications are subject to change without notice.
AC-167f (1/10) Page 8 of 8