Appliance Administration Manual

v8.1
rev. 1.0.5

Copyright © 2002 – 2016 Loadbalancer.org, Inc

Appliance Administration Manual v8.1 Loadbalancer.org

Table of Contents
Chapter 1 – Introduction.....................................................................................10
About this Manual................................................................................................................................................................... 11
About the Appliance............................................................................................................................................................... 11
Version 8.1........................................................................................................................................................................... 11
Appliance Configuration Overview................................................................................................................................... 15
Appliance Security.................................................................................................................................................................. 15
Deployment Guides............................................................................................................................................................... 16
Additional Information.......................................................................................................................................................... 16

Chapter 2 – Load Balancing Concepts............................................................17

Load Balancing – the Basics................................................................................................................................................ 18
Supported Protocols....................................................................................................................................................... 18
Layer 4 & Layer 7............................................................................................................................................................... 18
Load Balancing Algorithms.................................................................................................................................................. 18
Weighted Round Robin................................................................................................................................................... 18
Weighted Least Connection.......................................................................................................................................... 18
Destination Hashing........................................................................................................................................................ 18
Real Server Agent.............................................................................................................................................................. 18
Layer 4 vs Layer 7.................................................................................................................................................................... 19
Our Recommendation.................................................................................................................................................... 19
Loadbalancer.org Terminology.......................................................................................................................................... 20

Chapter 3 – Load Balancing Methods.............................................................21

Supported Methods............................................................................................................................................................... 22
One-Arm and Two-Arm Configurations................................................................................................................... 22
Direct Routing (DR).......................................................................................................................................................... 23
Network Address Translation (NAT)............................................................................................................................ 24
NAT Mode Packet re-Writing.................................................................................................................................. 25
Source Network Address Translation (SNAT) .......................................................................................................... 26
Other Considerations............................................................................................................................................................ 27
Does Your Application Cluster correctly Handle its own State?.......................................................................27
Replication Solutions for Shared Data................................................................................................................. 27
Solutions for Session Data....................................................................................................................................... 27
Persistence (aka Affinity)........................................................................................................................................... 27
What do You do if Your Application is not Stateless?...........................................................................................28
Loadbalancer.org Persistence Options............................................................................................................... 28
Which Load Balancing Method should I Use?............................................................................................................... 29
Our Recommendation.................................................................................................................................................... 29

Chapter 4 – Appliance Fundamentals............................................................30

The Hardware Appliance – Unpacking and Connecting........................................................................................... 31
The Virtual Appliance – Hypervisor Deployment........................................................................................................ 32
Supported Hypervisors................................................................................................................................................... 32
Host Requirements.......................................................................................................................................................... 32
Downloading the Appliance......................................................................................................................................... 32
VMware Deployment...................................................................................................................................................... 33

Page 2
Appliance Administration Manual v8.1 Loadbalancer.org

Hyper-V Deployment...................................................................................................................................................... 33
KVM Deployment............................................................................................................................................................. 34
XEN Deployment.............................................................................................................................................................. 34
Initial Network Interface Configuration.......................................................................................................................... 35
Using the Network Setup Wizard................................................................................................................................ 35
Using Linux Commands................................................................................................................................................. 36
Appliance Access & Configuration Methods.................................................................................................................. 37
Local Methods................................................................................................................................................................... 37
Console Access........................................................................................................................................................... 37
Appliance Configuration using Links................................................................................................................... 37
Keyboard Layout......................................................................................................................................................... 37
Remote Methods.............................................................................................................................................................. 38
Accessing the WUI..................................................................................................................................................... 39
Configuring the Appliance using the Wizard.................................................................................................... 39
Running the Wizard............................................................................................................................................. 39
Configuring the Appliance using the WUI.......................................................................................................... 41
Full Root Access...................................................................................................................................................................... 43
Appliance Configuration Files & Locations.............................................................................................................. 43

Chapter 5 – Appliance Management..............................................................44

Network Configuration......................................................................................................................................................... 45
Physical Interfaces........................................................................................................................................................... 45
Configuring IP Addresses.............................................................................................................................................. 45
Configuring Bonding...................................................................................................................................................... 46
Bonding Configuration Modes.............................................................................................................................. 47
Bonding for High-Availability (default mode)............................................................................................. 48
Bonding for Bandwidth...................................................................................................................................... 48
Bonding for High-Availability & Bandwidth................................................................................................. 48
Configuring VLANs.......................................................................................................................................................... 49
Configuring MTU Settings............................................................................................................................................. 50
Configuring Default Gateway & Static Routes........................................................................................................ 50
Configuring Hostname & DNS Configuration......................................................................................................... 51
System Date & Time and NTP Server Configuration................................................................................................... 52
Auto Configuration using NTP Servers...................................................................................................................... 52
Manual Configuration..................................................................................................................................................... 52
Appliance Internet Access via Proxy................................................................................................................................. 53
SMTP Relay Configuration................................................................................................................................................... 53
Syslog Server Configuration............................................................................................................................................... 54
SNMP Configuration.............................................................................................................................................................. 54
Installing License Keys.......................................................................................................................................................... 55
Running OS Level Commands........................................................................................................................................... 55
Restoring Manufacturer's Settings.................................................................................................................................... 56
Using the WUI.................................................................................................................................................................... 56
Using the Console / SSH Session................................................................................................................................ 56
Restarting & Reloading Services......................................................................................................................................... 57
Appliance Restart & Shutdown.......................................................................................................................................... 59
Appliance Software Updates............................................................................................................................................... 59
Checking the Current Software Version & Revision.............................................................................................. 59

Page 3
Appliance Administration Manual v8.1 Loadbalancer.org

Online Update................................................................................................................................................................... 60
Offline Update................................................................................................................................................................... 61
Updating a Clustered Pair.............................................................................................................................................. 62
Firewall Configuration.......................................................................................................................................................... 63
Manual Firewall Configuration..................................................................................................................................... 63
Firewall Lock-down Wizard.......................................................................................................................................... 64
Conntrack Table Size...................................................................................................................................................... 66
Users & Passwords................................................................................................................................................................. 66
Appliance Security Lockdown Script............................................................................................................................... 68
SSH Keys.................................................................................................................................................................................... 70

Chapter 6 – Configuring Load Balanced Services.......................................71

Layer 4 Services....................................................................................................................................................................... 72
The Basics........................................................................................................................................................................... 72
Creating Virtual Services (VIPs)..................................................................................................................................... 72
Modifying a Virtual Service...................................................................................................................................... 73
Creating Real Servers (RIPs)........................................................................................................................................... 76
Persistence Considerations........................................................................................................................................... 78
Persistence State Table Replication...................................................................................................................... 78
DR Mode Considerations............................................................................................................................................... 79
The ARP Problem....................................................................................................................................................... 79
Detecting the ARP Problem.................................................................................................................................... 79
Solving the ARP Problem for Linux....................................................................................................................... 79
Method 1 (using iptables)................................................................................................................................... 79
Method 2 (using arp_ignore sysctl values).................................................................................................. 80
Solving the ARP Problem for Solaris.................................................................................................................... 81
Solving the ARP Problem for Mac OS X / BSD..................................................................................................81
Solving the ARP Problem for Windows Servers............................................................................................... 82
Windows Server 2000........................................................................................................................................ 82
Windows Server 2003........................................................................................................................................ 85
Windows Server 2008........................................................................................................................................ 88
Windows Server 2012......................................................................................................................................... 92
Verifying netsh Settings for Windows 2008 & 2012.................................................................................96
Configuring IIS to Respond to both the RIP and VIP......................................................................................97
Windows Firewall Settings...................................................................................................................................... 99
NAT Mode Considerations........................................................................................................................................... 101
NAT Mode Potential Issues.................................................................................................................................... 101
Enabling Real Server Internet access using Auto-NAT...........................................................................101
Enabling Access to non Load-Balanced Services....................................................................................101
One-Arm (Single Subnet) NAT Mode................................................................................................................. 102
Route Configuration for Windows Servers................................................................................................ 102
Route Configuration for Linux Servers........................................................................................................ 103
Firewall Marks.................................................................................................................................................................. 103
Firewall Marks – Auto Configuration................................................................................................................. 103
Firewall Marks – Manual Configuration............................................................................................................ 104
Layer 4 – Advanced Configuration.......................................................................................................................... 109
Layer 7 Services...................................................................................................................................................................... 111
The Basics.......................................................................................................................................................................... 111

Page 4
Appliance Administration Manual v8.1 Loadbalancer.org

Creating Virtual Services (VIPs)................................................................................................................................... 111

Modifying a Virtual Service.................................................................................................................................... 112
Configuring Content Redirection (ACLs).......................................................................................................... 116
Creating Real Servers (RIPs)......................................................................................................................................... 118
Persistence Considerations......................................................................................................................................... 119
Persistence State Table Replication.................................................................................................................... 119
Layer 7 – Custom Configurations............................................................................................................................. 119
Configuring Manual Virtual Services.................................................................................................................. 119
Manual Config Ex. 1 – Simple HTTP Redirect...........................................................................................120
Manual Config Ex. 2 – Load Balancing with URL matching using ACL's..........................................121
HAProxy Error Codes..................................................................................................................................................... 123
Layer 7 – Advanced Configuration........................................................................................................................... 124
SSL Termination..................................................................................................................................................................... 127
Concepts........................................................................................................................................................................... 127
SSL Termination on the Real Servers (Recommended)......................................................................................128
SSL Termination on the Load Balancer................................................................................................................... 128
Creating an STunnel SSL Virtual Service (the Default SSL Terminator)...................................................129
STunnel Cipher Settings and the BEAST Attack.......................................................................................130
Creating a Pound SSL Virtual Service................................................................................................................. 131
Modifying a Pound SSL Virtual Service........................................................................................................ 133
Pound Cipher Settings and the BEAST Attack.......................................................................................... 133
Generating a CSR on the Load Balancer.......................................................................................................... 134
Using an Existing Certificate................................................................................................................................. 136
Creating a PEM file............................................................................................................................................. 136
Exporting PFX Certificates from Windows Servers.................................................................................136
Uploading PEM & PFX Certificates................................................................................................................ 136
Converting between certificate formats..................................................................................................... 137
SSL Re-encryption (aka SSL Bridging)................................................................................................................ 138
SSL – Advanced Configuration.................................................................................................................................. 139
HTTP to HTTPS Redirection.............................................................................................................................................. 141
SSL Termination on the Real Servers (Recommended)......................................................................................141
SSL Termination on the Load Balancer................................................................................................................... 142
Using Transparent Proxy (TProxy)................................................................................................................................... 143
TProxy & HAProxy.......................................................................................................................................................... 143
TProxy, HAProxy & Pound........................................................................................................................................... 144
TProxy, HAProxy & STunnel......................................................................................................................................... 145
Floating IPs............................................................................................................................................................................. 146
Server Feedback Agent....................................................................................................................................................... 147
Windows Agent............................................................................................................................................................... 147
Linux / Unix Agent.......................................................................................................................................................... 149
Custom HTTP Agent..................................................................................................................................................... 150
Configuration.................................................................................................................................................................. 150
Configuring VIPs & RIPs via Script & Command Line ............................................................................................... 151
Configuring L4 & L7 Services using the CLI Script (lbcli)....................................................................................151
Configuring Layer 4 Services using ipvsadm......................................................................................................... 153
Configuring Layer 7 Services using Linux Socket Commands.........................................................................154

Chapter 7 – Web Application Firewall (WAF)..............................................155

Page 5
Appliance Administration Manual v8.1 Loadbalancer.org

Introduction........................................................................................................................................................................... 156
Implementation Concepts................................................................................................................................................. 157
WAF Gateway Configuration............................................................................................................................................ 158
Initial Setup....................................................................................................................................................................... 158
WAF Gateway Operating Mode................................................................................................................................. 160
WAF Gateway Rules...................................................................................................................................................... 160
WAF Gateway Logging & Monitoring............................................................................................................................. 162
Modifying Default Actions................................................................................................................................................. 163

Chapter 8 – Real Server Health Monitoring & Control...........................164

Configuring Health Checks............................................................................................................................................... 165
Heath Checks for Layer 4 Services........................................................................................................................... 165
Health Checks for Layer 7 Services.......................................................................................................................... 168
Simulating Health-Check Failures............................................................................................................................. 171
Disabling Health-Checks.............................................................................................................................................. 171
Fallback Server Settings................................................................................................................................................ 171
Configuring Email Alerts..................................................................................................................................................... 173
Layer 4................................................................................................................................................................................ 173
Global Settings.......................................................................................................................................................... 173
VIP Level Settings..................................................................................................................................................... 174
Layer 7................................................................................................................................................................................ 175
Real Server Monitoring & Control using System Overview.....................................................................................176
Real Server Monitoring................................................................................................................................................. 176
Real Server Control........................................................................................................................................................ 177
Ordering of VIPs.............................................................................................................................................................. 178
Sort by Column......................................................................................................................................................... 178
Drag & Drop............................................................................................................................................................... 179
Real Server Control using the HAProxy Statistics Page........................................................................................... 180

Chapter 9 – Appliance Clustering for HA.....................................................181

Introduction........................................................................................................................................................................... 182
Clustered Pair Considerations.......................................................................................................................................... 182
Master / Slave Operation............................................................................................................................................. 182
Heartbeat.................................................................................................................................................................... 182
Master Slave Replication........................................................................................................................................ 182
Settings that are NOT Replicated to the Slave Appliance.....................................................................182
High Availability Configuration........................................................................................................................................ 183
To Create an HA Pair (Add a slave)............................................................................................................................ 183
To Break an HA Pair (Remove a slave)..................................................................................................................... 184
Promoting a Slave to Master............................................................................................................................................. 186
Configuring Heartbeat........................................................................................................................................................ 187
Clustered Pair Diagnostics................................................................................................................................................ 189
Heartbeat State Diagnostics....................................................................................................................................... 189
Split Brain Scenarios...................................................................................................................................................... 190
Forcing Master/Slave Failover & Failback................................................................................................................ 191
Testing & Verifying Master/Slave Replication & Failover....................................................................................192

Chapter 10 – Application Specific Settings.................................................195

Page 6
Appliance Administration Manual v8.1 Loadbalancer.org

FTP............................................................................................................................................................................................ 196
Layer 4 Virtual Services for FTP................................................................................................................................. 196
FTP Layer 4 Negotiate Health Check................................................................................................................. 196
FTP Recommended Persistence Settings......................................................................................................... 197
Layer 7 Virtual Services for FTP.................................................................................................................................. 197
Active Mode............................................................................................................................................................... 197
Windows 2008 Example................................................................................................................................. 198
Passive Mode............................................................................................................................................................. 199
Windows 2008 Example................................................................................................................................. 200
Limiting Passive FTP Ports..................................................................................................................................... 201
For Windows 2008............................................................................................................................................ 201
For Windows 2003............................................................................................................................................ 202
For Windows 2000........................................................................................................................................... 202
For Linux............................................................................................................................................................... 202
Terminal Services / Remote Desktop Services........................................................................................................... 203
Layer 4 – IP Persistence......................................................................................................................................... 203
Layer 7 – Microsoft Connection Broker / Session Directory.....................................................................203
Layer 7 – RDP Cookies.......................................................................................................................................... 204
Other Applications.............................................................................................................................................................. 204

Chapter 11 – Configuration Examples..........................................................205

Introduction........................................................................................................................................................................... 206
Initial Network Settings............................................................................................................................................... 206
Example 1 – One-Arm DR Mode (Single Appliance)................................................................................................ 206
Configuration Overview.............................................................................................................................................. 206
Network Settings........................................................................................................................................................... 206
N.B. this step can be skipped if all network settings have already been configured...............................206
Virtual Service (VIP)....................................................................................................................................................... 207
Real Servers (RIPs)......................................................................................................................................................... 208
Real Server Changes – Solve the ARP Problem................................................................................................... 208
Basic Testing & Verification........................................................................................................................................ 209
Example 2 – Two-Arm NAT Mode (Clustered Pair).................................................................................................... 210
Configuration Overview.............................................................................................................................................. 210
Master Unit – Network Settings................................................................................................................................ 210
Slave Unit – Network Settings.................................................................................................................................... 211
Master Unit – Heartbeat Settings.............................................................................................................................. 213
Checking the Status...................................................................................................................................................... 214
Virtual Service (VIP)........................................................................................................................................................ 214
Real Servers (RIP)............................................................................................................................................................ 215
Real Server Changes – Set the Default Gateway................................................................................................. 215
Verify the Slave Configuration................................................................................................................................... 216
Basic Testing & Verification......................................................................................................................................... 216
Example 3 – One-Arm SNAT Mode & SSL Termination (Single Appliance)........................................................217
Configuration Overview............................................................................................................................................... 217
Network Settings............................................................................................................................................................ 217
Virtual Service (VIP)........................................................................................................................................................ 219
Real Servers (RIP)............................................................................................................................................................ 219
SSL Termination.............................................................................................................................................................. 220

Page 7
Appliance Administration Manual v8.1 Loadbalancer.org

Basic Testing & Verification......................................................................................................................................... 221

Chapter 12 – Testing Load Balanced Services...........................................222

Testing Load Balanced Services...................................................................................................................................... 223
Diagnosing VIP Connection Problems................................................................................................................... 223
Taking Real Servers Offline......................................................................................................................................... 224
Using Log Files................................................................................................................................................................ 225
Using Reports.................................................................................................................................................................. 225

Chapter 13 – Appliance Monitoring..............................................................226

Appliance Log Files.............................................................................................................................................................. 227
Load Balancer.................................................................................................................................................................. 227
Layer 4............................................................................................................................................................................... 227
Layer 7................................................................................................................................................................................ 227
SSL Termination (Pound).............................................................................................................................................. 227
SSL Termination (STunnel)........................................................................................................................................... 227
Heartbeat.......................................................................................................................................................................... 227
Apache Error Log............................................................................................................................................................ 227
Apache User Log............................................................................................................................................................ 227
WAF Logs.......................................................................................................................................................................... 228
Appliance Reports................................................................................................................................................................ 228
Layer 4 Status.................................................................................................................................................................. 228
Layer 4 Traffic Rate........................................................................................................................................................ 229
Layer 4 traffic Counters............................................................................................................................................... 230
Layer 4 Current Connections..................................................................................................................................... 231
Layer 4 Current Connections (resolve hostnames)............................................................................................. 231
Layer 7 Status................................................................................................................................................................... 231
Layer 7 Stick Table......................................................................................................................................................... 232
Graphing................................................................................................................................................................................. 232
Graphs – Load Balanced Services............................................................................................................................ 232
Graphs – Appliance Specific...................................................................................................................................... 235
Graph Options................................................................................................................................................................ 236
SNMP Reporting................................................................................................................................................................... 238
SNMP for Layer 4 Based Services............................................................................................................................. 238
Monitoring Layer 4 VIPs & RIPs using SNMP................................................................................................... 238
SNMP for Layer 7 Based Services.............................................................................................................................. 239
Monitoring Layer 7 RIPs using SNMP................................................................................................................ 239

Chapter 14 – Useful Tools & Utilities.............................................................241

Useful Diagnostics Tools................................................................................................................................................... 242
Netstat............................................................................................................................................................................... 242
Telnet................................................................................................................................................................................. 242
Tcpdump........................................................................................................................................................................... 243
Ethtool............................................................................................................................................................................... 243
Wireshark.......................................................................................................................................................................... 244
Windows Specific Tools..................................................................................................................................................... 244
WinSCP.............................................................................................................................................................................. 244
PuTTy................................................................................................................................................................................. 244

Page 8
Appliance Administration Manual v8.1 Loadbalancer.org

Remote Support Tools....................................................................................................................................................... 245

Chapter 15 – Backup & Restore and Disaster Recovery.........................246

Introduction........................................................................................................................................................................... 247
Backup & Restore................................................................................................................................................................. 247
Restoring XML Files....................................................................................................................................................... 248
Disaster Recovery................................................................................................................................................................ 249
Being Prepared............................................................................................................................................................... 249
Backing Up SSH System Files............................................................................................................................... 249
Backing Up Configuration Files to a Remote Location...............................................................................249
Using wget to Copy the Files............................................................................................................................... 250
Backing up locally on the Load Balancer......................................................................................................... 250
Appliance Recovery using a USB Memory Stick.................................................................................................. 250
Disaster Recovery After Slave Failure....................................................................................................................... 253
Recovery Steps......................................................................................................................................................... 253
Verify the HA Configuration................................................................................................................................. 254
Creating a Slave XML File from the Running Master.....................................................................................254
Disaster Recovery After Master Failure.................................................................................................................... 255
Recovery Steps......................................................................................................................................................... 255
Verify the HA Configuration................................................................................................................................. 256
Creating a Master XML File from the Running Slave.....................................................................................256

Chapter 16 – Technical Support.....................................................................257

Introduction........................................................................................................................................................................... 258
WUI Support Options......................................................................................................................................................... 258
Contact Us....................................................................................................................................................................... 258
Technical Support Download.................................................................................................................................... 259
Useful Links...................................................................................................................................................................... 260

Appendix..................................................................................................................261
Front & Rear Panel Layouts............................................................................................................................................... 262
IPMI (Remote Management) Configuration for the Enterprise R20 & MAX.......................................................263
iDRAC (Remote Management) Configuration for the Enterprise 10G & R320.................................................267
Appliance IPv4 Address Format (CIDR notation)....................................................................................................... 268
Company Contact Information....................................................................................................................................... 269

Page 9
Appliance Administration Manual v8.1 Loadbalancer.org

Chapter 1 – Introduction

Chapter 1 – Introduction Page 10

 Appliance Administration Manual v8.1 Loadbalancer.org

About this Manual

This document covers all required administration information for v8.1 Loadbalancer.org appliances.

About the Appliance

The Loadbalancer.org appliance runs the GNU/Linux operating system with a custom kernel configured for
load balancing.
The core software is based on customized versions of Centos 6.x / RHEL 6.x, Linux 3.10.x, LVS, HA-Linux,
HAProxy, Pound, STunnel & Ldirectord. Full root access is provided which enables complete control of all
settings.
The appliance is available in the following formats: hardware, virtual (VMware, HyperV, KVM, XEN) and
cloud based (Amazon, Azure).
Appliances can be deployed as single units or as a clustered pair.

NOTE : Loadbalancer.org always recommend that clustered pairs should be used where possible
for high availability and resilience, this avoids introducing a single point of failure to your network.
For more information on configuring an HA pair please refer to page 181.

Version 8.1
The latest version of the appliance (v8.1.1) includes the following new features, updates and bug fixes:

HAProxy

• HAProxy updated to 1.7

• Source hash persistence is Deprecated

• Edit ACL Rules modal would not load in firefox 38.2.1 ESR

• Performance improvement for viewing a large number of stick table entries has been made

WAF

• We have updated the /etc/httpd/modsecurity.d/modsecurity_crs_10_config.conf to fully enable

anomaly scoring. If you have made any change to the above file please back it up first

• Disabling the ProxyVia header is now possible

• Anomaly scores were not being correctly updated

• Further Isolation of the WAF from the web interface as they now run as 2 separate processes

HyperV

• Numa is now disabled at boot

Chapter 1 – Introduction Page 11

 Appliance Administration Manual v8.1 Loadbalancer.org

Syslog

• Its now possible to enter a hostname as the syslog server

Pound

• Pound was unable to start if it did not own an IP address. This has been rectified

Heartbeat

• Breaking A HA-Pair left users with the inability to change the eth0 IP address

Other

• Openssl Updated to 1.0.1s

• STunnel Updated to 5.31

EC2

• Amazon ec2 php sdk updated to 2.8.27 allowing usage of the Frankfurt region

• Enable the possibility to use the appliance without a IAM role being set

• Integration with Auto Scaling groups to dynamically update running configuration

RPMS

• bash-4.1.2-33.el6_7.1.x86_64.rpm

• bind-libs-9.8.2-0.37.rc1.el6_7.6.x86_64.rpm

• bind-utils-9.8.2-0.37.rc1.el6_7.6.x86_64.rpm

• binutils-2.20.51.0.2-5.43.el6.x86_64.rpm

• cairo-1.8.8-6.el6_6.x86_64.rpm

• checkpolicy-2.0.22-1.el6.x86_64.rpm

• chkconfig-1.3.49.3-5.el6_7.2.x86_64.rpm

• coreutils-8.4-37.el6_7.3.x86_64.rpm

• coreutils-libs-8.4-37.el6_7.3.x86_64.rpm

• cronie-1.4.4-15.el6_7.1.x86_64.rpm

• cronie-noanacron-1.4.4-15.el6_7.1.x86_64.rpm

• db4-4.7.25-20.el6_7.x86_64.rpm

• db4-utils-4.7.25-20.el6_7.x86_64.rpm

• dbus-glib-0.86-6.el6.x86_64.rpm

• device-mapper-1.02.95-3.el6_7.4.x86_64.rpm

Chapter 1 – Introduction Page 12

Appliance Administration Manual v8.1 Loadbalancer.org

• device-mapper-libs-1.02.95-3.el6_7.4.x86_64.rpm

• dmidecode-2.12-6.el6.x86_64.rpm

• e2fsprogs-1.41.12-22.el6.x86_64.rpm

• e2fsprogs-libs-1.41.12-22.el6.x86_64.rpm

• elfutils-0.161-3.el6.x86_64.rpm

• elfutils-libelf-0.161-3.el6.x86_64.rpm

• elfutils-libs-0.161-3.el6.x86_64.rpm

• ethtool-3.5-6.el6.x86_64.rpm

• gawk-3.1.7-10.el6_7.3.x86_64.rpm

• gdbm-1.8.0-38.el6.x86_64.rpm

• glibc-2.12-1.166.el6_7.7.x86_64.rpm

• glibc-common-2.12-1.166.el6_7.7.x86_64.rpm

• grep-2.20-3.el6_7.1.x86_64.rpm

• hwdata-0.233-14.1.el6.noarch.rpm

• iproute-2.6.32-45.el6.x86_64.rpm

• iptables-1.4.7-16.el6.x86_64.rpm

• iptables-ipv6-1.4.7-16.el6.x86_64.rpm

• iputils-20071127-20.el6.x86_64.rpm

• krb5-libs-1.10.3-42.el6.x86_64.rpm

• libcom_err-1.41.12-22.el6.x86_64.rpm

• libdrm-2.4.59-2.el6.x86_64.rpm

• libgcc-4.4.7-16.el6.x86_64.rpm

• libpcap-1.4.0-4.20130826git2dbcaa1.el6.x86_64.rpm

• libpng-1.2.49-2.el6_7.x86_64.rpm

• libselinux-utils-2.0.94-5.8.el6.x86_64.rpm

• libsemanage-2.0.43-5.1.el6.x86_64.rpm

• libss-1.41.12-22.el6.x86_64.rpm

• libstdc++-4.4.7-16.el6.x86_64.rpm

• libudev-147-2.63.el6_7.1.x86_64.rpm

• libuser-0.56.13-8.el6_7.x86_64.rpm

• libX11-1.6.0-6.el6.x86_64.rpm

• libX11-common-1.6.0-6.el6.noarch.rpm

Chapter 1 – Introduction Page 13

Appliance Administration Manual v8.1 Loadbalancer.org

• libxcb-1.9.1-3.el6.x86_64.rpm

• libxml2-2.7.6-20.el6_7.1.x86_64.rpm

• logrotate-3.7.8-26.el6_7.x86_64.rpm

• mod_ssl-2.2.15-47.el6.centos.3.x86_64.rpm

• module-init-tools-3.9-25.el6.x86_64.rpm

• nc-1.84-24.el6.x86_64.rpm

• ncurses-5.7-4.20090207.el6.x86_64.rpm

• ncurses-base-5.7-4.20090207.el6.x86_64.rpm

• ncurses-libs-5.7-4.20090207.el6.x86_64.rpm

• net-snmp-5.5-54.el6_7.1.x86_64.rpm

• net-snmp-libs-5.5-54.el6_7.1.x86_64.rpm

• net-snmp-perl-5.5-54.el6_7.1.x86_64.rpm

• net-snmp-utils-5.5-54.el6_7.1.x86_64.rpm

• nspr-4.10.8-2.el6_7.x86_64.rpm

• nss-3.19.1-8.el6_7.x86_64.rpm

• nss_compat_ossl-0.9.6-2.el6_7.x86_64.rpm

• nss-softokn-3.14.3-23.el6_7.x86_64.rpm

• nss-softokn-freebl-3.14.3-23.el6_7.x86_64.rpm

• nss-sysinit-3.19.1-8.el6_7.x86_64.rpm

• nss-tools-3.19.1-8.el6_7.x86_64.rpm

• nss-util-3.19.1-5.el6_7.x86_64.rpm

• ntp-4.2.6p5-5.el6.centos.4.x86_64.rpm

• ntpdate-4.2.6p5-5.el6.centos.4.x86_64.rpm

• openldap-2.4.40-7.el6_7.x86_64.rpm

• openssh-5.3p1-112.el6_7.x86_64.rpm

• openssh-clients-5.3p1-112.el6_7.x86_64.rpm

• openssh-server-5.3p1-112.el6_7.x86_64.rpm

• openssl-1.0.1e-42.el6_7.4.x86_64.rpm

• pam-1.1.1-20.el6_7.1.x86_64.rpm

• parted-2.1-29.el6.x86_64.rpm

• python-2.6.6-64.el6.x86_64.rpm

• python-libs-2.6.6-64.el6.x86_64.rpm

Chapter 1 – Introduction Page 14

 Appliance Administration Manual v8.1 Loadbalancer.org

• rpm-4.8.0-47.el6.x86_64.rpm

• rpm-libs-4.8.0-47.el6.x86_64.rpm

• rpm-python-4.8.0-47.el6.x86_64.rpm

• tar-1.23-13.el6.x86_64.rpm

• tcpdump-4.0.0-5.20090921gitdf3cb4.2.el6.x86_64.rpm

• tzdata-2016a-2.el6.noarch.rpm

• udev-147-2.63.el6_7.1.x86_64.rpm

• ustr-1.0.4-9.1.el6.x86_64.rpm

• vim-common-7.4.629-5.el6.x86_64.rpm

• vim-enhanced-7.4.629-5.el6.x86_64.rpm

• vim-filesystem-7.4.629-5.el6.x86_64.rpm

• vim-minimal-7.4.629-5.el6.x86_64.rpm

Appliance Configuration Overview

Initial network configuration can be carried out on the console by using the Network Setup Wizard, using
standard Linux network setup commands, or by connecting to the default IP address:port in a browser
(192.168.2.21:9080) and making changes using the WUI.
Once the network is configured, the appliance can be configured manually or by using the Setup Wizard
(for layer 7 services). The WUI is accessible using HTTP on port 9080 and HTTPS on port 9443. It's also
possible to configure the load balancer at the console using the text based Links browser, although using
the WUI is the recommended method.
For a clustered pair, we recommend that the master is fully configured first, then the slave should be
added. For more information on configuring a clustered pair, please refer to page 181. Once a pair is
configured, load balanced services must be configured & modified on the master appliance. The slave
appliance will then be kept in sync automatically.

Appliance Security
The appliance includes a security lockdown command (lbsecure) that enables passwords to set, network
access to be locked down and SSH key regeneration in one simple step. This command can be run on a
single appliance or an HA pair. For more details please refer to page 68.

Chapter 1 – Introduction Page 15

 Appliance Administration Manual v8.1 Loadbalancer.org

Deployment Guides
Deployment guides have also been written that focus on load balancing specific applications. An up to
date listing is available on the applications page of our website: www.loadbalancer.org/applications/

At the time of writing, the following deployment & quick-reference guides are available:

• Load Balancing Microsoft IIS Web Servers

• Load Balancing Microsoft Terminal Services

• Load Balancing Microsoft Remote Desktop Services

• Load Balancing Microsoft Exchange 2013

• Load Balancing Microsoft Exchange 2010

• Load Balancing Microsoft Sharepoint

• Load Balancing Microsoft AD FS

• Load Balancing Microsoft DirectAccess

• Load Balancing VMware View

• Load Balancing Microsoft Lync 2010

• Load Balancing Microsoft OCS 2007 R2

• Load Balancing Web Proxies/Filters/Gateways (generic guide)

• Load Balancing Bloxx Web Filter

• Load Balancing McAfee Web Gateway

• Load Balancing Smoothwall Web Gateway

• Load Balancing Barracuda Web Filter

• Load Balancing Clearswift Web Gateway

• Load Balancing Trend Micro Web Gateway

• Load Balancing Sophos Web Gateway

• Load Balancing RSA Authentication Manager

• Load Balancing Oracle Application Server

• Load balancing Medical Imaging & Information Systems Protocols

Additional Information
This manual should provide you with enough information to be very productive with your
Loadbalancer.org appliance. However, if there are aspects of the appliance that have not been covered, or
if you have any questions, please contact our support team : [email protected].

Chapter 1 – Introduction Page 16

Appliance Administration Manual v8.1 Loadbalancer.org

Chapter 2 – Load Balancing Concepts

Chapter 2 – Load Balancing Concepts Page 17

 Appliance Administration Manual v8.1 Loadbalancer.org

Load Balancing – the Basics

Loadbalancer.org appliances enable two or more servers to be combined into a cluster. This enables
inbound requests to be distributed across multiple servers which provides improved performance,
reliability and resilience. Appliances can also be deployed as a clustered pair (our recommended solution)
which creates a highly-available configuration.

Supported Protocols
Loadbalancer.org appliances support virtually any TCP or UDP based protocol including HTTP, HTTPS, FTP,
SMTP, RDP, SIP, IMAP, POP, DNS etc. etc.

Layer 4 & Layer 7

Load balancing at layer 4 and layer 7 is supported. LVS (Linux Virtual Server) is utilized at layer 4 whilst
HAProxy is used at layer 7.

Load Balancing Algorithms

The Loadbalancer.org appliance supports several different load balancing algorithms. Each one has its
advantages and disadvantages and it depends on the specific application which is the most appropriate to
use. Usually the default method Weighted Least Connection is a good solution which works well in most
situations. The following sections summarize each method supported.

Weighted Round Robin

With this method incoming requests are distributed to Real Servers proportionally to the Real Servers
weight. Servers with higher weights receive new jobs first and get more jobs than servers with lower
weights. Servers with equal weights get an equal distribution of new jobs. This method addresses the
weakness of the simple round robin method. Weightings are relative, so it makes no difference if Real
Server #1 and #2 have weightings of 50 and 100 respectively or 5 and 10 respectively.

Weighted Least Connection

This method distributes incoming requests based on the number of current connections and also the
weighting of each server. Again, weightings are relative, so it makes no difference if Real Server #1 and #2
have weightings of 50 and 100 respectively or 5 and 10 respectively.
This is the default method for new VIPs.

Destination Hashing
This algorithm assign jobs to servers through looking up a statically assigned hash table by their
destination IP addresses.

Real Server Agent

To compliment the methods above, Loadbalancer.org appliances also support Real Server (i.e back-end
server) agents. This permits the load balancing algorithm to be dynamically modified based on each Real
Servers running characteristics. For example, one Real Server could have a run-away process that is
consuming excessive CPU resources or RAM. Without the agent, the load balancer has no way of knowing
this and would continue to send requests to the overloaded server based on the algorithm selected. With
the agent installed on the Real Server, feedback is provided to the load balancer and the algorithm is then
adjusted to reduce requests that are sent to that server. For more details on using the agent please refer to
page 147.

Chapter 2 – Load Balancing Concepts Page 18

 Appliance Administration Manual v8.1 Loadbalancer.org

Layer 4 vs Layer 7
A fundamental choice when setting up the load balancer is whether to configure the services at layer 4 or
layer 7.

The Basics
At layer 4 the primary protocols used are TCP and UDP. These protocols are not aware of upper level
protocols such as FTP, HTTP, HTTPS, DNS, RDP etc. Therefore the load balancer can only make load
balancing decisions based on details available at layers 4 and below such as port numbers and IP
addresses. At layer 7, the load balancer has more information to make load balancing related decisions
since more information about upper levels protocols is available.
Layer 7 load balancing uses a proxy at the application layer (HAProxy). HTTP requests are terminated on
the load balancer, and the proxy generates a new request which is passed to the chosen Real Server.

Performance
Due to the increased amount of information at layer 7, performance is not as fast as at layer 4. If raw
throughput is a primary concern, then layer 4 is probably the better choice.

Persistence
Persistence (aka affinity or sticky connections) is the ability to ensure that a specific client connects back to
the same server within a specific time limit. It is normally required when the session state is stored locally
on the web server rather than in a separate database. At Layer 4, Source IP persistence is the only option.
At layer 7, additional methods are available such as HTTP cookie persistence where the load balancer sets
a cookie to identify the session and Microsoft Connection Broker where the load balancer is able to utilize
the redirection token for reconnecting users to existing sessions.

Real Server Changes

At Layer 4, either the ARP problem (please refer to page 79 for more details) has to be solved (required
when using Layer4 DR mode) or the default gateway on the Real Servers must be set to point at the load
balancer (required when using Layer 4 NAT mode). At Layer 7, the connection is fully proxied and therefore
the Real Servers do not need to be changed in any way.

Transparency
Transparency refers to the ability to see the originating IP address of the client. Connections at Layer 4 are
always transparent where as at layer 7 the IP address of the load balancer is recorded as the source address
unless additional configuration steps are taken (such as using TProxy or utilizing the X-Forwarded-For
headers, please see pages 143 and 115 respectively).

Our Recommendation
Where possible we recommend that Layer 4 Direct Routing (DR) mode is used. This offers the best possible
performance since replies go direct from the Real Servers to the client, not via the load balancer. It's also
relatively simple to implement.
Ultimately, the final choice depends on your specific requirements and infrastructure. If you need any
advice - whether you're an existing customer or just trialing, don't hesitate to contact our support team:
[email protected]

Chapter 2 – Load Balancing Concepts Page 19

Appliance Administration Manual v8.1 Loadbalancer.org

Loadbalancer.org Terminology

Acronym Terminology

Load Balancer An IP based traffic manager for server clusters

VIP Virtual IP address – the address of the load balanced cluster of RIPs,
the address presented to connecting clients

Floating IP The Floating IP Address is automatically created whenever a VIP is

configured, the FIP address is the same as the VIP address, it enables
services to be moved between the master and slave appliance

RIP The Real IP address of a back-end server in the cluster

GW The Default Gateway for a back-end server in the cluster

WUI Web User Interface

Layer 4 Part of the seven layer OSI model, descriptive term for a network
device that can route packets based on TCP/IP header information

Layer 7 Part of the seven layer OSI model, descriptive term for a network
device that can read and write the entire TCP/IP header and payload
information at the application layer

DR Direct Routing (aka DSR / Direct Server Return) is a standard load

balancing technique that distributes packets by altering only the
destination MAC address of the packet

NAT Network Address Translation – Standard load balancing technique

that changes the destination of packets to and from the VIP (external
subnet to internal cluster subnet)

SNAT Source Network Address Translation – the load balancer acts as a

(HAProxy) proxy for all incoming & outgoing traffic

SSL Termination The SSL certificate is installed on the load balancer in order to
(Pound & STunnel) decrypt HTTPS traffic on behalf of the cluster

MASQUERADE Descriptive term for standard firewall technique where internal

servers are represented as an external public IP address. Sometimes
referred to as a combination of SNAT & DNAT rules

One-Arm The load balancer has one physical network card connected to one
subnet

Two-Arm The load balancer has two interfaces connected to two subnets -
this can be achieved using two physical network cards or by
assigning two addresses to one physical network card

Eth0 Usually the internal interface also known as Gb0

Eth1 Usually the external interface also known as Gb1

Chapter 2 – Load Balancing Concepts Page 20

Appliance Administration Manual v8.1 Loadbalancer.org

Chapter 3 – Load Balancing Methods

Chapter 3 – Load Balancing Methods Page 21

 Appliance Administration Manual v8.1 Loadbalancer.org

Supported Methods
The Loadbalancer.org appliance is one of the most flexible load balancers on the market. The design
allows different load balancing modules to utilize the core high availability framework of the appliance.

Multiple load balancing methods can be used at the same time or in combination with each other.

Layer 4 DR Ultra-fast local server based load balancing One-Arm

(Direct Routing) Requires solving the 'ARP problem' on the Real
Servers
Layer 4 NAT Fast Layer 4 load balancing, the appliance becomes Two-Arm
(Network Address the default gateway for the Real Servers
Translation) The appliance must be the default
gateway for the Real Servers
Layer 4 TUN Similar to DR but works across IP encapsulated tunnels One-Arm

Layer 7 SSL Termination Usually required in order to process cookie persistence One or Two-
(Pound & STunnel) in HTTPS streams on the load balancer Arm
Processor intensive
Layer 7 SNAT Layer 7 allows great flexibility including full SNAT and One or Two-
(Source Network WAN load balancing, cookie insertion and URL Arm
Address Translation: switching
HAProxy) Not as fast as Layer 4

Key:

Recommended for high performance fully transparent and scalable solutions

Recommended if HTTP cookie persistence is required, also used for several Microsoft
applications such as Exchange, Sharepoint & Remote Desktop Services and for overall
deployment simplicity since real servers can be on any accessible subnet and no
Real-Server changes are required

Only required for Direct Routing implementation across routed networks (rarely used)

One-Arm and Two-Arm Configurations

The number of 'arms' is normally a descriptive term for how many physical connections (Ethernet
interfaces) are used to connect a device to a network. It's very common for a load balancer that uses a
routing method (NAT) to have a two-arm configuration. Proxy based load balancers (SNAT) commonly use
a one-arm configuration.

One-Arm The load balancer has one physical network card connected to one subnet
The load balancer has two interfaces connected to two subnets – this can be
Two-Arm achieved using two physical network cards or by assigning two addresses to one
physical network card

Chapter 3 – Load Balancing Methods Page 22

 Appliance Administration Manual v8.1 Loadbalancer.org

Direct Routing (DR)

One-arm direct routing (DR) mode is a very high performance solution that requires little change to your
existing infrastructure. N.B. Kemp, Brocade, Barracuda & A10 Networks call this Direct Server Return and F5
call it N-Path.

 Direct Routing mode works by changing the destination MAC address of the incoming packet to
match the selected Real Server on the fly which is very fast
 When the packet reaches the Real Server it expects it to own the Virtual Services IP address (VIP).
This means that you need to ensure that the Real Server (and the load balanced application)
respond to both the Real Servers own IP address and the VIP
 The Real Server should not respond to ARP requests for the VIP. Only the load balancer should do
this. Configuring the Real Servers in this way is referred to as Solving the ARP Problem. Please refer
to page 79 onwards for more details on this
 On average, DR mode is 8 times quicker than NAT for HTTP, 50 times quicker for Terminal Services
and much, much faster for streaming media or FTP
 The load balancer must have an Interface in the same subnet as the Real Servers to ensure layer 2
connectivity required for DR mode to work
 The VIP can be brought up on the same subnet as the Real Servers, or on a different subnet
provided that the load balancer has an interface in that subnet
 Port translation is not possible in DR mode i.e. having a different RIP port than the VIP port
 DR mode is transparent, i.e. the Real Server will see the source IP address of the client

Chapter 3 – Load Balancing Methods Page 23

 Appliance Administration Manual v8.1 Loadbalancer.org

Network Address Translation (NAT)

Sometimes it's not possible to use DR mode. The two most common reasons being: if the application
cannot bind to the RIP & VIP at the same time; or if the host operating system cannot be modified to
handle the ARP problem. The second choice is Network Address Translation (NAT) mode. The basic
requirement is that return traffic MUST go back via the load balancer.

 The load balancer translates all requests from the external Virtual Service to the internal Real
Servers
 Normally eth0 is used for the internal network and eth1 is used for the external network although
this is not mandatory. If the Real Servers require Internet access, Autonat should be enabled using
the WUI option: Cluster Configuration > Layer 4 – Advanced Configuration, the external interface
should be selected
 NAT mode can be deployed in the following ways:
2-arm (using 2 Interfaces), 2 subnets (as shown above) - One interface on the load balancer is
connected to subnet1 and the second interface and Real Servers are connected to subnet2. The
VIP is brought up in subnet1. The default gateway on the Real Servers is set to be an IP address in
subnet2 on the load balancer. Clients can be located in subnet1 or any remote subnet provided
they can route to the VIP
2-arm (using 1 Interface), 2 subnets - same as above except that a single interface on the load
balancer is allocated 2 IP addresses, one in each subnet
1-arm (using 1 Interface), 1 subnet - Here, the VIP is brought up in the same subnet as the Real
Servers. For clients located in remote networks the default gateway on the Real Servers must be
set to be an IP address on the load balancer. For clients located on the same subnet, return traffic
would normally be sent directly to the client bypassing the load balancer which would break NAT
mode. To address this, the routing table on the Real Servers must be modified to force return
traffic to go via the load balancer - For more details on 'One-Arm NAT Mode' refer to page 102
 If you want Real Servers to be accessible on their own IP address for non-load balanced services,
e.g. SMTP or RDP, you will need to setup individual SNAT and DNAT firewall script rules for each
Real Server or add additional VIPs for this - please refer to page 101 for more details
 NAT mode is transparent, i.e. the Real Server will see the source IP address of the client
 Port translation is possible in NAT mode, i.e. VIP:80 → RIP8080 is possible

Chapter 3 – Load Balancing Methods Page 24

 Appliance Administration Manual v8.1 Loadbalancer.org

NAT Mode Packet re-Writing

In NAT mode, the inbound destination IP address is changed by the load balancer from the Virtual Service
IP address (VIP) to the Real Server. For outbound replies the load balancer changes the source IP address
of the Real Server to be the Virtual Services IP address.

The following table shows an example NAT mode setup:

Protocol VIP Port RIP Port

TCP 10.0.0.20 80 192.168.1.50 80

In this simple example all traffic destined for IP address 10.0.0.20 on port 80 is load-balanced to the real IP
address 192.168.1.50 on port 80.

Packet rewriting works as follows:

1) The incoming packet for the web server has source and destination addresses as:

SOURCE x.x.x.x:34567 DEST 10.0.0.20:80

2) The packet is rewritten and forwarded to the back-end server as:

SOURCE x.x.x.x:34567 DEST 192.168.1.50:80

3) Replies return to the load balancer as:

SOURCE 192.168.1.50:80 DEST x.x.x.x:34567

4) The packet is written back to the VIP address and returned to the client as:

SOURCE 10.0.0.20:80 DEST x.x.x.x:34567

Chapter 3 – Load Balancing Methods Page 25

 Appliance Administration Manual v8.1 Loadbalancer.org

Source Network Address Translation (SNAT)

If your application requires that the load balancer handles cookie insertion then you need to use SNAT
mode. This mode is also used with numerous Microsoft applications such as Exchange, Sharepoint, Lync
etc.

This mode has can be deployed in one-arm or two-arm configuration and does not require any changes to
the application servers. However, since the load balancer is acting as a full proxy it doesn't have the same
raw throughput as the layer 4 methods.

The network diagram for the Layer 7 HAProxy SNAT mode is very similar to the Direct Routing example
except that no re-configuration of the Real Servers is required. The load balancer proxies the application
traffic to the servers so that the source of all traffic becomes the load balancer.

 SNAT is a full proxy and therefore load balanced Real Servers do not need to be changed in any
way
 Because SNAT is a full proxy any server in the cluster can be on any accessible subnet including
across the Internet or WAN

 SNAT is not transparent by default, i.e. the Real Servers will not see the source IP address of the
client, they will see the load balancers IP address. If required, this can be solved by either enabling
TProxy on the load balancer, or for HTTP, using X-forwarded-For headers. Please refer to pages
143 and 115 respectively for more details.
 SNAT mode can be deployed using either a 1-arm or 2-arm configuration

NOTE : For detailed configuration examples using various modes, please refer to chapter 11
starting on page 205.

Chapter 3 – Load Balancing Methods Page 26

 Appliance Administration Manual v8.1 Loadbalancer.org

Other Considerations

Does Your Application Cluster correctly Handle its own State?

NOTE : Load balancers work most effectively if the application servers are completely
stateless. This means that if a web server fails and is automatically taken out of the cluster;
then all the current user sessions will be transferred to other servers in the cluster without
the users needing to re login to the application again. If your application doesn't have a
persistent data store then you can't have seamless fail over for your back-end servers.

Do your web servers store persistent information on local drives?

 Images (jpeg, png, gif etc.)

 Files (html, php, asp etc.)

If so, these files either need to be on shared storage such as an NFS/CIFS mount, or they need to be
replicated to all of the nodes in the cluster.

Replication Solutions for Shared Data

On UNIX you can use the RSYNC command to replicate files, on Windows Server you can use RSYNC as
well but you may prefer ROBOCOPY that's included by default in newer versions of Windows Server or in
the resource kit for older versions. Usually you will upload your content to one master server and then
replicate it to the other servers in the cluster.

Solutions for Session Data

Standard ASP and PHP session data is stored locally by default, leaving your session data in a local store
will prevent you from implementing seamless application server fail-over in your cluster. If an application
server fails, all of the local session data will be lost and your user will need to re-log in and possibly lose
shopping baskets etc.

This problem is easily resolvable by implementing a shared persistent data store for the cluster. This is
usually either done with a shared back-end database or a shared memory solution.

Persistence (aka Affinity)

Persistence is a feature that is required by many web applications. Once a user has interacted with a
particular server all subsequent requests are sent to the same server thus persisting to that particular
server. It is normally required when the session state is stored locally to the web server as opposed to a
database.

Chapter 3 – Load Balancing Methods Page 27

 Appliance Administration Manual v8.1 Loadbalancer.org

What do You do if Your Application is not Stateless?

Some applications require state to be maintained such as:

 Terminal Services / Remote Desktop Services

 SSH
 FTP (upload)
 SMTP (incoming)

You may also find that you are unable to modify your HTTP/HTTPS based application to handle shared
session data.

For these cases, you can use persistence based on source IP address. You lose the ability to have
transparent fail-over, but you do still get increased capacity and manageability. This persistence problem
occurs with all load balancers and all vendors use standard methods and technologies to mitigate the
issue.

Loadbalancer.org Persistence Options

 Source IP (subnet)
 Cookie (Active or Passive)
 SSL session ID
 Microsoft Connection Broker / Session Broker Integration

The standard Layer 4 persistence method is source IP persistence, you can handle millions of persistent
connections at Layer 4. Just modify your Virtual Service to be persistent if you require source IP
persistence.

Cookies are a Layer 7 based persistence method that can offer more even traffic distribution and also
handle any clients where the source IP address may change during the session (e.g. mega proxies).

SSL session ID based persistence is useful in certain circumstances, although due to the way some
browsers operate – notably older versions of Internet Explorer, the session ID can be renegotiated
frequently (every few seconds) which effectively breaks the persistence.

Chapter 3 – Load Balancing Methods Page 28

 Appliance Administration Manual v8.1 Loadbalancer.org

Which Load Balancing Method should I Use?

Layer 4 DR Mode offers the best performance and requires limited physical Real Server changes. The
server application must be able to bind to the both the RIP & VIP at the same time.

Layer 4 NAT Mode is also a high performance solution but not as fast as DR mode. It requires the
implementation of a two-arm infrastructure with an internal and external subnet to carry out the
translation (the same way a firewall works). Also each Real Server must use the load balancer as the default
gateway.

Layer 7 SNAT Mode offers greater flexibility but at lower performance levels. It supports HTTP cookie
insertion, RDP cookies, Connection Broker integration and works very well with either Pound or STunnel
when SSL termination is required. It does not require any changes to the application servers and can be
deployed in one-arm or two-arm mode and. HAProxy is a high performance solution, but since it operates
as a full proxy, it cannot perform as fast as the layer 4 solutions.

Our Recommendation
Where possible we recommend that Layer 4 Direct Routing (DR) mode is used. This offers the best possible
performance since replies go directly from the Real Servers to the client, not via the load balancer. It's also
relatively simple to implement.

Ultimately, the final choice does depend on your specific requirements and infrastructure.

IMPORTANT NOTE : If you are using Microsoft Windows Real Servers (i.e. back-end servers)
make sure that Windows NLB (Network Load Balancing) is completely disabled to ensure that this
does not interfere with the operation of the load balancer.

Chapter 3 – Load Balancing Methods Page 29

Appliance Administration Manual v8.1 Loadbalancer.org

Chapter 4 – Appliance Fundamentals

Chapter 4 – Appliance Fundamentals Page 30

 Appliance Administration Manual v8.1 Loadbalancer.org

The Hardware Appliance – Unpacking and Connecting

 Remove all packaging

 Rack mount the appliance if required

 The power supply is an auto sensing unit (100v to 240v)

 Connect the power lead from the power socket to the mains or UPS

 Connect a network cable from the switch to one of the Ethernet ports – typically eth0 but this is
not mandatory

 If using a two-armed configuration connect another cable to a second Ethernet port – typically
eth1 but this is not mandatory

 For a clustered hardware pair, the units must be able to communicate either via network (ucast),
via serial cable or both. By default, ucast only is used. If serial is preferred or you want to use both
methods, connect a serial cable (1 supplied with each appliance) between the two appliances.
N.B. If a serial cable is used, Heartbeat must be configured for this using the WUI option: Cluster
Configuration > Heartbeat Configuration and enabling 'Serial'

 Attach a monitor to the VGA port and keyboard to the USB or PS/2 port

 Check mains power is on and press the power switch to start the appliance (the fans should start &
front panel LED’s should light)

 Allow a minute for booting

Serial connection eth1 is usually

for the fail-over eth0 is usually the external
(heartbeat) cable the internal network
network

N.B. The above image shows the Enterprise MAX, for connecting other models please refer to page 262 in
the Appendix.

Chapter 4 – Appliance Fundamentals Page 31

 Appliance Administration Manual v8.1 Loadbalancer.org

The Virtual Appliance – Hypervisor Deployment

Supported Hypervisors
Currently, the Virtual Appliance is available for the following hypervisors:

• VMware & Virtual Box

• Microsoft Hyper-V

• KVM

• XEN

Host Requirements
To run the Loadbalancer.org Enterprise VA (irrespective of which Hypervisor is being used) the following
basic server specifications must be met:

• 64bit CPU
• Virtual Technology hardware support – either Intel-VT or AMD-V compliant CPU's

For an Intel based server, VT must be enabled in the BIOS as shown in the example below:

If your server is unable to support 64bit guests, an error message will be displayed when attempting to
start the VA.

Downloading the Appliance

All downloads are accessible from the following location: http://www.loadbalancer.org/resources/free-
trial
To access the downloads, enter your name, email address and phone number (optional), specify the
application that you'll be load balancing (optional) and select the Hypervisor type. Once the details have
been entered, click Download Now. The various download links will then be presented on screen and
we'll also send you an email containing the same links.
Once downloaded, extract the archive using your preferred utility. The download also includes a quickstart
guide which covers the VA deployment process in more detail.

Chapter 4 – Appliance Fundamentals Page 32

 Appliance Administration Manual v8.1 Loadbalancer.org

NOTE : All information provided is 100% confidential. We may follow up with an email or
phone call to see how you're getting on with the trial and offer assistance but under no
circumstances will Loadbalancer.org send you other promotional material or share your
information with a third party.

VMware Deployment
The steps required depend on which VMware environment is in use. The following list provides a basic
guideline:

• For vSphere Client use: File > Deploy ovf Template

• For VMware Workstation use: File > Open
• For VMware Player use: Player > File > Open

Hyper-V Deployment

Windows 2008 R2

1. Start Hyper-V Manager, then using the right-click menu or the Actions pane select Import Virtual
Machine and then click Next
2. Browse to the location of the extracted download and select the folder LBVMHYPER-Vv8
3. Select the option "Copy the virtual machine (create a new unique ID)" and also select the
"Duplicate all files so the same virtual machine can be imported again" check-box, click Import
4. The import will start, once complete the new appliance will appear in the Virtual Machine list
5. The appliance has 4 NIC cards, to connect these right-click the appliance and select Settings then
for each Network Adapter select the required network
6. Right-click and select Start to power up the appliance, allow a minute to boot
7. If you're deploying a clustered pair, you'll first need to do one of the following steps before
importing the second virtual machine. If this is not done, the second virtual machine cannot be
deployed because the disk from the first import already exists, and there will therefore be a
conflict:
i) Shutdown the first VM and modify the name of the disk
or
ii) Change the default file location using the Hyper-V Settings option in the Actions pane
Once one of the above is done, repeat steps 1-6 to create the second virtual machine.

Windows 2012

1. Start Hyper-V Manager, then using the right-click menu or the Actions pane select Import Virtual
Machine then click Next
2. Browse to the location of the extracted download and select the folder LBVMHYPER-V3v8
3. Click Next until prompted for the Import Type, make sure that 'Copy the virtual machine (create a

Chapter 4 – Appliance Fundamentals Page 33

 Appliance Administration Manual v8.1 Loadbalancer.org

new unique ID)' is selected and click Next

4. Tick the check-box 'Store the Virtual Machine in different location', then define a suitable location
for the virtual machines files and click Next
5. Define a location for the virtual hard disk files
6. Click Next, then click Finish to complete the import process. Once complete, the load balancer
will appear in the Virtual Machines list
7. The appliance has 4 NIC cards, to connect these right-click the appliance and select Settings then
for each Network Adapter select the required network
8. Highlight the new load balancer and start it either by using the right-click menu or the Actions
pane

If you're deploying a clustered pair, repeat steps 2-8 for the slave unit, making sure that a different folder
location is selected in steps 4 & 5.

KVM Deployment
The following steps should be followed on the KVM host:

1. Extract the archive to /var/lib/libvirt/images/

2. virsh define Loadbalancer*.xml
3. virsh start Loadbalancer*

N.B. Network cards are set to NAT by default so adjust as needed before powering on. Also, please refer to
the included XML file for additional configuration notes

XEN Deployment
The following steps should be followed on the XEN host:

1. Extract the archive

2. Import the xva file into XEN

NOTE : For more details of the cloud based products, please refer to the relevant quick start
guide available in the documentation library.

Chapter 4 – Appliance Fundamentals Page 34

 Appliance Administration Manual v8.1 Loadbalancer.org

Initial Network Interface Configuration

By default the load balancer is pre-configured with the following IP address & subnet mask:

192.168.2.21/24 (192.168.2.21 / 255.255.255.0)

This default address can be changed at the console in two ways:

 Using the built-in Network Setup Wizard

 Using traditional Linux commands

NOTE : For the VA, four NICs are included but only eth0 is connected by default at power on.
If the other NICs are required, these should be connected using the network configuration
screen within the Hypervisor.

Using the Network Setup Wizard

To run the wizard, login to the console of the appliance as the 'setup' user. This is explained in the initial
console start-up message as shown below:

login to the console:

Username : setup
Password : setup

Once logged in, enter the IP address / mask, default gateway & DNS servers at the prompts as shown
below:

Chapter 4 – Appliance Fundamentals Page 35

 Appliance Administration Manual v8.1 Loadbalancer.org

After the required settings have been entered, a summary will be presented along with details of how to
access the WUI as shown below:

As mentioned in the text the IP address is now configured for interface eth0.

IP addresses for the other interfaces can now be configured using the WUI option: Local Configuration >
Network Interface Configuration (to access the WUI please refer to pages 39 and 41) or by using Linux
commands as explained in the following section.

Using Linux Commands

at the console or via an SSH session login as root:

Username: root
Password: loadbalancer

set the IP address using the following command:

ip addr add <IP address>/<mask> dev eth0

e.g.

ip addr add 192.168.1.100/24 dev eth0

set the default gateway using the following command:

route add default gw <IP address> <interface>

e.g.

route add default gw 192.168.1.254 eth0

N.B. Setting the IP address in this way is temporary, the IP address MUST be set via the WUI to make
this permanent otherwise settings will be lost after a reboot

Chapter 4 – Appliance Fundamentals Page 36

 Appliance Administration Manual v8.1 Loadbalancer.org

Appliance Access & Configuration Methods

The appliance can be accessed & configured both locally and remotely.

Local Methods

Console Access
To access the console, simply connect a monitor and keyboard to the load balancer, power up and you'll
be presented with a login prompt. The console can also be accessed via the serial port if the default
heartbeat configuration is used - i.e. heartbeat is configured to communicate over the network only.

Log in to the console:

Username: root
Password: loadbalancer

Appliance Configuration using Links

Once logged into the console, the text based Links browser can be used to configure the appliance. To
start Links and bring up the text based administration interface use the following command:

links 127.0.0.1:9080

Log in to Links:

Username: loadbalancer
Password: loadbalancer

Use the Up, Down & Enter keys to move between and select the various menu options.

N.B. The preferred configuration method is the WUI which can be accessed via a browser as detailed
on page 39.

Keyboard Layout
To change the keyboard locale edit the file: /etc/sysconfig/keyboard, e.g. to change from a UK to a US
layout:

1. edit /etc/sysconfig/keyboard using a browser such as 'vi' or 'vim' for Linux or WinSCP under
Windows
2. replace KEYTABLE="uk" with KEYTABLE="us"
3. re-boot the appliance

Chapter 4 – Appliance Fundamentals Page 37

 Appliance Administration Manual v8.1 Loadbalancer.org

Remote Methods
When configuring the appliance remotely, take care when changing network and firewall settings. If you
do lock yourself out, you'll either need local console access or you can use remote management tools
such as IPMI or iDRAC. The Enterprise R20 and Enterprise MAX include IPMI support, iDRAC is included on
the Enterprise 10G & R320. For details on configuring both IPMI & iDRAC please refer to the Appendix.

The appliance can be remotely accessed using the following tools:

 HTTP / HTTPS Web Browser Web User Interface (WUI)

 OpenSSH (Linux hosts) or PuTTy (Windows hosts) Secure Shell Access

 OpenSCP (Linux hosts) or WinSCP (Windows hosts) Secure File Transfer

Chapter 4 – Appliance Fundamentals Page 38

 Appliance Administration Manual v8.1 Loadbalancer.org

Accessing the WUI

The WUI is accessed using a browser such as Firefox, Chrome etc. Appliance authentication is based on
Apache .htaccess files. User admin tasks such as adding users and changing passwords can be performed
using the WUI option: Maintenance > Passwords.

 Using a web browser, access the WUI using the following URL:
http://192.168.2.21:9080/lbadmin/
(replace 192.168.2.21 with your IP address if it's been changed)

N.B. If you prefer you can use the HTTPS administration address:
https://192.168.2.21:9443/lbadmin/
(replace 192.168.2.21 with your IP address if it's been changed)

 Login to the WUI:

Username : loadbalancer
Password : loadbalancer

 Once logged in, you'll be asked if you want to run the web based setup wizard. If you click
[Accept] the Layer 7 Virtual Service configuration wizard will start. If you prefer to configure the
appliance manually, simple click [Dismiss].

NOTE : A number of compatibility issues have been found with various versions of IE. The
WUI has been tested and verified using both Firefox & Chrome.

Configuring the Appliance using the Wizard

The wizard can be used to setup one or more Layer 7 Virtual Services and associated Real Servers. Layer 4
services must be configured manually.

Running the Wizard

First, set the IP address using one of the methods described on page 35. Then open the WUI and start the
wizard by clicking the [Accept] link shown above, or by using the WUI option: Cluster Configuration >
Setup Wizard and clicking General Layer 7 Virtual Service, and continue as detailed below:

Chapter 4 – Appliance Fundamentals Page 39

Appliance Administration Manual v8.1 Loadbalancer.org

• Define the required Virtual Service settings as shown in the example below:

• Click Create Virtual Service

• Now continue and add the associated Real Servers as shown below:

• Use the Add Real Server button to define additional Real Servers, once all are defined click Attach
Real Servers

• Finally reload HAProxy using the Reload HAProxy button in the blue box at the top of the screen
or by using the WUI option: Maintenance > Restart Services and clicking Reload HAProxy

Chapter 4 – Appliance Fundamentals Page 40

 Appliance Administration Manual v8.1 Loadbalancer.org

NOTE : Running the wizard again will permit additional Layer 7 VIPs and associated RIPs to
be defined.

NOTE : To restore manufacturer's settings use the WUI option: Maintenance > Backup &
Restore > Restore Manufacturer's Defaults . N.B. this will reset the IP address to
192.168.2.21/24

Configuring the Appliance using the WUI

If you have already used the web based wizard, then you will already be using the WUI. From here all
administration tasks can be carried out. If not, access the WUI as follows:

With a web browser access the WUI: http://192.168.2.21:9080/lbadmin/

(replace 192.168.2.21 with the correct IP address)

log in to the WUI:

Username : loadbalancer
Password : loadbalancer

N.B. If you prefer you can use the HTTPS administration address: https://192.168.2.21:9443/lbadmin/

Once logged in, the WUI is displayed:

Chapter 4 – Appliance Fundamentals Page 41

 Appliance Administration Manual v8.1 Loadbalancer.org

Main Menu Options:

System Overview – Displays a graphical summary of all VIPs, RIPs and key appliance statistics
Local Configuration – Configure local host settings such as IP address, DNS, system time etc.
Cluster Configuration – Configure load balanced services such as VIPs & RIPs
Maintenance – Perform maintenance tasks such as service restarts and taking backups
View Configuration – Display the saved appliance configuration settings
Reports – View various appliance reports & graphs
Logs – View various appliance logs
Support – Create a support download, contact the support team & access useful links

Chapter 4 – Appliance Fundamentals Page 42

 Appliance Administration Manual v8.1 Loadbalancer.org

Full Root Access

One of the great advantages of the Loadbalancer.org appliance is that you have full root access. This
unlocks the benefits of the underlying Linux OS. Other vendors tend to lock this down and only provide
limited access to certain tools.

Appliance Configuration Files & Locations

Network configuration: /etc/sysconfig/network-scripts/ifcfg-eth*

Firewall configuration: /etc/rc.d/rc.firewall
Firewall Lock down wizard: /etc/rc.d/rc.lockdownwizard.conf
XML configuration file: /etc/loadbalancer.org/lb_config.xml
Layer 4 configuration: /etc/ha.d/conf/loadbalancer.cf
Layer 7 HAProxy configuration: /etc/haproxy/haproxy.cfg
Pound SSL configuration: /etc/pound/pound.cfg
STunnel configuration: /etc/stunnel/stunnel.conf
SSL Certificates: /etc/loadbalancer.org/certs
Heartbeat configuration: /etc/ha.d/ha.cf

NOTE : If you do require a custom configuration please contact our support team to discuss
your requirements : [email protected]

Chapter 4 – Appliance Fundamentals Page 43

Appliance Administration Manual v8.1 Loadbalancer.org

Chapter 5 – Appliance Management

Chapter 5 – Appliance Management Page 44

 Appliance Administration Manual v8.1 Loadbalancer.org

Network Configuration

Physical Interfaces
All hardware and virtual models have 4 network interfaces. For the VA, only the first interface is connected
by default, the other interfaces can be connected when required using the Hypervisor's management
interface. If multiple logical interfaces are required, these can be added simply by specifying multiple IP
addresses as shown on the following page. If multiple cables must be connected, an external switch can
be used.
Typically, the main reason for using all 4 interfaces is when bonding (e.g. 802.3ad) is required in a two-arm
NAT mode (layer 4) or two-arm SNAT mode (layer 7) highly available configuration.

Configuring IP Addresses
IP addresses can be configured using the WUI option: Local Configuration > Network Interface
Configuration. If a single interface is required, eth0 is typically used. If 2 interfaces are required, eth0 is
typically used as the internal interface and eth1 is used as the external interface. However, unlike other
appliances on the market you can use any interface for any purpose.

In a simple one-arm configuration, you would just need to configure the IP address and subnet mask for
one interface, e.g. eth0 and if there are remote clients, the relevant default gateway. Both IPv4 and IPv6
addresses can be configured.

CIDR notation is used to specify IP addresses and subnet masks. For example, to specify an IP address of
192.168.2.100 with a subnet mask of 255.255.255.0, then 192.168.2.100/24 would be entered in the
relevant interface field as shown in the example below:

Please refer to page 268 in the the appendix for more details on CIDR notation.

To set IP address(es):

 In the WUI, open Local Configuration > Network Interface Configuration

 Assign the required IP address/mask, multiple addresses can be assigned as shown below:

Chapter 5 – Appliance Management Page 45

Appliance Administration Manual v8.1 Loadbalancer.org

 Click Configure Interfaces

NOTE : If you already have Virtual Services defined when making changes to the network
configuration, you should verify that your Virtual Services are still up and working correctly
after making the changes.

NOTE : For the VA, four NICs are included but only eth0 is connected by default at power on.
If the other NICs are required, these should be connected using the network configuration
screen within the Hypervisor.

Configuring Bonding
 In the WUI, open Local Configuration > Network Interface Configuration

 If you want to bond eth0 and eth1, check the box named Bond eth0 & eth1 as bond0

Chapter 5 – Appliance Management Page 46

 Appliance Administration Manual v8.1 Loadbalancer.org

 Click Modify Bonding

 The eth0 and eth1 fields will be replaced with bond0

NOTE : At this point the interfaces will still have the same IP settings configured previously.
Once an IP address is defined for the bond and Configure Interfaces in clicked these
addresses will be removed and only the bond address will apply. If bonding is later disabled
these addresses will be re-applied to the interfaces.

 Enter the IP address for bond0 and click Configure Interfaces

NOTE : If you have a master and slave configured as an HA pair, make sure you configure
bonding in the same way on both units. Failure to do this will result in heartbeat (master /
slave communication) related issues.

Bonding Configuration Modes

Ideally all single points of failure should be eliminated from a network. To help achieve this a cross-wired
switch environment can be used. Every server including the load balancers is cross wired into two switch
stacks. Then, if a network switch fails the servers & load balancers will activate the connection to the
second switch.

Loadbalancer.org appliances support this using the standard Linux bonding driver. Once you have setup
the appliance using a single network card and are happy with the configuration you can set up bonding
using Local Configuration > Network Interface Configuration.

Chapter 5 – Appliance Management Page 47

 Appliance Administration Manual v8.1 Loadbalancer.org

If required you can change the bonding mode in the file: /etc/modprobe.d/loadbalancer.conf. By default
mode 1 is used which configures the bond for high availability. Simply edit the file and set the mode setting
as needed.

Supported Modes:

Bonding for High-Availability (default mode)

mode=1

alias bond0 bonding

options bond0 miimon=100 mode=1

Bonding for Bandwidth

Change to mode 0

alias bond0 bonding

options bond0 miimon=100 mode=0

Bonding for High-Availability & Bandwidth

Change to mode 4

alias bond0 bonding

options bond0 miimon=100 mode=4

This option requires the ports on the switch to be configured as a TRUNK with 802.3ad support.

NOTE : If your Real Servers, ESX hosts etc. support network bonding using Broadcom's SLB
(Smart Load Balancing), this can cause issues in Layer 4 DR mode if older drivers are used. We
have successfully tested SLB (Auto Fallback Disable) with driver version 15.2.0.5. Therefore at
least this version is recommended.

Chapter 5 – Appliance Management Page 48

 Appliance Administration Manual v8.1 Loadbalancer.org

Configuring VLANs
Native 802.1Q VLAN support can be enabled to load balance clusters on multiple VLANs.
In access mode, switch ports are dedicated to one VLAN. The switch handles all the tagging and detagging
of frames – the station connected to the port does not need to be configured for the VLAN at all. In trunk
mode, the switch passes on the raw VLAN frames, and the station must be configured to handle them.
Trunk mode is usually used to connect two VLAN-carrying switches, or to connect a server or router to a
switch.
If the load balancer is connected to an access mode switch port no VLAN configuration is required. If the
load balancer is connected to a trunk port, then all the required VLANs will need to be configured on the
load balancer.

To configure a VLAN:

 In the WUI, open Local Configuration > Network Configuration

 In the VLAN section select the required interface (e.g. eth0)

 Enter the VLAN ID (e.g. 250)

 Click Add VLAN

 An extra IP Address Assignment field named eth0.250 will be created as shown below, the required IP
address should be entered in this field

 Click Configure Interfaces

To delete the VLAN definition, click the appropriate Delete button

NOTE : If you have a clustered pair, don't forget to configure the same VLANs on the slave as
these will not be replicated / created automatically.

Chapter 5 – Appliance Management Page 49

 Appliance Administration Manual v8.1 Loadbalancer.org

Configuring MTU Settings

To set the MTU setting for an interface:

 In the WUI, open Local Configuration > Network Configuration

 Enter the required MTU setting

 Click Configure Interfaces

Configuring Default Gateway & Static Routes

To set the Default Gateway for IPv4 and Ipv6:

 In the WUI, open Local Configuration > Routing

 In the Default Gateway section define the default gateway as shown in the example below:

 Click Configure Routing

To configure Static Routes:

 In the WUI, open Local Configuration > Routing

 In the Static Routes section configure the subnets & gateway addresses shown in the example below:

Chapter 5 – Appliance Management Page 50

 Appliance Administration Manual v8.1 Loadbalancer.org

 Click Configure Routing

N.B. Unlimited static routes can be defined, additional blank rows will be added to the WUI screen as
they're used

Configuring Hostname & DNS Configuration

To set the Hostname, Domain & DNS servers:

 In the WUI, open Local Configuration > Hostname & DNS

 Specify the required Hostname, by default this is set to lbmaster

 Specify the Domain name, by default this is set to localhost

 Specify the required DNS servers

 Click Update

Chapter 5 – Appliance Management Page 51

 Appliance Administration Manual v8.1 Loadbalancer.org

System Date & Time and NTP Server Configuration

Auto Configuration using NTP Servers

To configure NTP:

 In the WUI, open Local Configuration > System Date & Time

 Select the required System Timezone

 Define your NTP servers using the NTP Servers fields

 Click Set Timezone & NTP

Manual Configuration

To manually set the date & time:

 Set the data & time using the Date & time fields

 Click Set Date & Time

Chapter 5 – Appliance Management Page 52

 Appliance Administration Manual v8.1 Loadbalancer.org

NOTE : When using a clustered pair (i.e. master & slave) date and time changes on the master
will not be automatically replicated to the slave, therefore the date and time on the slave
must also be set manually.

Appliance Internet Access via Proxy

The appliance supports the ability to access the Internet via a proxy server.

To set the Proxy Server's IP address & Port:

 In the WUI, open Local Configuration > Physical Advanced Configuration

 Enter an appropriate IP address in the IP Address field

 Enter an appropriate port in the Port field

 Click Update

SMTP Relay Configuration

The appliance can be configured with an SMTP smart host to receive all mail messages generated by the
load balancer. If this field is not configured the address will be auto-configured based on an MX lookup of
the destination email address that's configured under Cluster Configuration > Layer 4 – Advanced
Configuration.

To configure a smart host:

 In the WUI, open Local Configuration > Physical Advanced Configuration

 Enter an appropriate IP address or hostname in the Smart Host field

 Click Update

Chapter 5 – Appliance Management Page 53

 Appliance Administration Manual v8.1 Loadbalancer.org

Syslog Server Configuration

The appliance supports the ability to write all logs either locally, to an external Syslog Server or both. The
Syslog server may be specified by IP address or hostname.

To configure a Syslog server:

 In the WUI, open Local Configuration > Physical Advanced Configuration

 Define whether logs should be local, written to a remote Syslog server or both

 Enter an appropriate IP address or hostname in the Remote Syslog Server field

 Click Update

SNMP Configuration
The appliance supports SNMP. Typical SNMP settings can be configured using the WUI.

To Configure SNMP:

 In the WUI, open Local Configuration > SNMP Configuration

 Set the required settings (If you leave the fields blank, default values will be applied)

 Click Update

Chapter 5 – Appliance Management Page 54

 Appliance Administration Manual v8.1 Loadbalancer.org

NOTE : Please refer to page 238 for details of the various OIDs and associated MIBs for the
appliance.

Installing License Keys

License keys are required for all appliances. At initial power up, the VA will display the following message:

The hardware appliance will display the following message:

To install the license:

 In the WUI, open Local Configuration > License Key

 Browse to the license file provided when the appliance was purchased

 Click Install License Key

Running OS Level Commands

The appliance supports the ability to run OS level commands directly from the WUI.

To run a command:

 In the WUI, open Local Configuration > Execute Shell Command

Chapter 5 – Appliance Management Page 55

 Appliance Administration Manual v8.1 Loadbalancer.org

 Enter the relevant command in the field

 Click Execute Shell Command

 The results of the command as well as any errors will be displayed at the top of the screen.

Restoring Manufacturer's Settings

The load balancers settings can be reset to factory default values in two ways. In both cases this will
remove all custom configuration from the load balancer. All VIPs and RIPs will be removed and the IP
address configured for eth0 will be set to 192.168.2.21/24.

Using the WUI

To restore settings:

 In the WUI, open Maintenance > Backup & Restore > Restore Tab

 Click Restore Manufacturer's Defaults

Once restored, restart the appliance to complete the process.

Using the Console / SSH Session

Run the following command:

lbrestore

Once restored, restart the appliance to complete the process.

Chapter 5 – Appliance Management Page 56

 Appliance Administration Manual v8.1 Loadbalancer.org

Restarting & Reloading Services

The various services running on the appliance can be manually reloaded or restarted if required. This is
normally only required for HAProxy, Pound, STunnel and Heartbeat when configuration changes are made.

Restart Ldirectord
Restart Layer 4 Services. Restarting Ldirectord will result in a loss of layer 4 services during the restart. This
causes the related process to be stopped and a new instance started. Generally only needed if Ldirectord
has failed for some reason and needs to be started again from scratch.

Reload Ldirectord
Reload Layer 4 Services. The Ldirectord configuration is re-read and re-applied. Note that a reload occurs
automatically whenever a layer 4 VIP or RIP and added, deleted or modified.

Restart HAProxy
Restart Layer 7 Services. Restarting HAProxy will result in a loss of layer 7 services during the restart
Restarting HAProxy will cause any persistence tables to be dropped and all connections to be closed, it's a
complete restart and reload of the HAProxy configuration.

Reload HAProxy
Reload Layer 7 Services. HAProxy will start a new process (leaving the old one) with the new configuration.
New connections will be passed onto this process, the old process will maintain existing connections and
eventually terminate when there are no more connections accessing it. If you are using stick tables for
persistence the entries will be copied between processes.

Chapter 5 – Appliance Management Page 57

 Appliance Administration Manual v8.1 Loadbalancer.org

N.B. If you have long lasting TCP connections it can take quite some time for the old process to terminate,
leaving those users running the old configuration. If this is taking too long – See Restart HAProxy.

Clear HAProxy Stick Table

Clears All HAProxy persistence tables. If you are using a Layer 7 persistence mode that relies on stick-tables
(IP persistence or RDP cookie persistence), this option will clear all entries from these tables. Once cleared,
clients may be directed to a different server upon re-connection.

Restart Pound
Restart Pound SSL Termination Service. Restarting Pound will result in a loss of SSL termination services
during the restart.

Restart STunnel
Restart STunnel SSL Termination Service. Restarting STunnel will result in a loss of SSL termination services
during the restart.

Restart Heartbeat
Restart Heartbeat Services. Restarting Heartbeat will result in a loss of service during the restart. Restarting
heartbeat will cause a temporary loss of all layer 4, layer 7 and SSL services.

Reload Heartbeat
This option forces heartbeat to stop (for the active member of an HA pair the floating IP's will also be taken
down, for a single unit they will be left up) then after an appropriate delay heartbeat is reloaded.

Restart Firewall
Restarts iptables. This will clear then re-read and re-apply the firewall rules.

Restart Syslogd
Restart the syslog service.

Restart Collectd
Restart the graphs data collector service.

Restart SNMPD
Restart the SNMP service.

Reload Apache
Reload the Apache service.

Chapter 5 – Appliance Management Page 58

 Appliance Administration Manual v8.1 Loadbalancer.org

Appliance Restart & Shutdown

The appliance can be restarted or shutdown using the WUI.

To restart or shutdown the appliance:

 In the WUI, open Maintenance > System Control

 Select the required option:

Restart Load Balancer – Shutdown and restart the appliance

Halt Load Balancer – Shutdown and halt the appliance

Appliance Software Updates

Loadbalancer.org continually develop and add new and improved features to the appliance. To ensure that
customers can benefit from this and can also receive bug fixes and security updates, Loadbalancer.org
have an online and an offline update facility that allows customers who have a valid maintenance and
support contract to keep their appliance fully up to date. A security updates only option is also available for
customers that don't require the benefits of our complete support package.

NOTE : Since services may be restarted during the update process we recommend
performing the update during a maintenance window.

For some updates (e.g. v7.5.4 to 7.6) a full appliance restart is required. In these cases a restart
notification message will be displayed after the update is complete.

Checking the Current Software Version & Revision

The software version number is displayed in the top right corner of the WUI. To determine the current
revision run the following command at the console, via an SSH session or via the WUI using the following
command:

cat /etc/loadbalancer.org/version.txt

Chapter 5 – Appliance Management Page 59

 Appliance Administration Manual v8.1 Loadbalancer.org

Online Update

To perform an online update:

 In the WUI, open Maintenance > Software Update

 Select Online Update

 If the latest version is already installed, the following message will be displayed:

 If an update is available, Information similar to the following will be displayed:

Chapter 5 – Appliance Management Page 60

 Appliance Administration Manual v8.1 Loadbalancer.org

 Enter the Authorisation key from your Technical Support document and click Online Update

 Once complete (the update can take several minutes depending on download speed and upgrade
version) the following message is displayed:

 If there are any specific post upgrade requirements such as a service restart these will be displayed on
the screen after the installation completes.

Notes:

• As indicated in the WUI, we recommend that you should backup your XML configuration and
firewall script (if changes have been made) using the links provided before running the update

• Make sure that the load balancer is able to access the Internet – if you have a proxy server, this can
be defined using Local Configuration > Physical Advanced Configuration

• Make sure that the default gateway is set correctly (Local Configuration > Routing)

• Make sure that a valid DNS server is specified (Local Configuration > Hostname & DNS)

Offline Update
If the load balancer does not have access to the Internet, Offline Update can be used.

To perform an offline update:

 In the WUI, open Maintenance > Software Update

 Select Offline Update

 The following screen will be displayed:

Chapter 5 – Appliance Management Page 61

 Appliance Administration Manual v8.1 Loadbalancer.org

 As explained in the on-screen text, contact the Loadbalancer.org support to obtain the archive &
checksum files

 Browse to and select these files

 Click Upload and Install

Updating a Clustered Pair

NOTE : Since services may be restarted during the update process, we recommend
performing the update during a maintenance window.

To update a clustered pair:

1. Perform the update on the slave first. The updates are incremental, so we recommend installing
each update in turn, ignoring calls to restart services or reboot the appliance until all available
updates have been installed and the appliance is fully up to date.
2. Next, restart services or reboot the appliance as directed.
3. Now update the master unit in the same way.

IMPORTANT NOTE : For a clustered pair, we strongly recommend fully testing & validating
the master / slave failover process before going live. If testing was not carried out before go-
live, we recommend scheduling a maintenance window to do this. For detailed steps, please
refer to page 192.

Chapter 5 – Appliance Management Page 62

 Appliance Administration Manual v8.1 Loadbalancer.org

Firewall Configuration

NOTE : Whilst the load balancer is capable of supporting complex firewall rules, we do not
recommend using the load balancer as your main bastion host. We recommend that the load
balancer is deployed behind your external firewall.

If you want to configure firewall rules, some points to consider are:

1. All Virtual Service connections are dealt with on the INPUT chain not the FORWARD chain

2. The WUI runs on HTTP port 9080 and HTTPS port 9443

3. SSH on the load balancer listens on the standard port (22)

4. SNAT & DNAT is handled automatically for all layer 4 NAT mode (LVS) and layer 7 (HAProxy) based
Virtual/Real load balanced services

5. You can use the standard Linux filters against spoofing attacks and syn floods

6. LVS has built in DOS attack filters that can be implemented

7. Plenty of extra information is available on the Internet relating to Linux Netfilter and LVS, if you
need any assistance please email our support team : [email protected]

Manual Firewall Configuration

The firewall can be configured manually using the WUI based script editor. This enables iptables rules and
any other required commands to be easily defined. The form allows you to directly edit
/etc/rc.d/rc.firewall.
Custom rules can be configured, or for belt & braces security your external firewall settings can be
replicated on to the load balancer for multi-layer security.
If you're planning to use NAT mode you may want to use the load balancer as your main firewall but we
recommend it is better and simpler to keep your firewall separate from the load balancer, especially if you
want to set up VPNs etc.
You can also use the firewall script to group ports together using Firewall Marks (see page 103).

To configure custom firewall rules:

 In the WUI, open Maintenance > Firewall Script

 The following screen will be displayed:

Chapter 5 – Appliance Management Page 63

 Appliance Administration Manual v8.1 Loadbalancer.org

 Define additional rules anywhere in the script above the last two lines:
echo "Firewall Activated"
exit 0;

 Click Update

WARNING : Be careful ! - make a backup before changing this script so that you know you
can roll everything back if you cause a problem. A backup can be created using the WUI
option: Maintenance > Backup & Restore > Make Local Firewall Script Backup

Firewall Lock-down Wizard

The firewall lock down wizard can be used to automatically configure the load balancer to allow access to
the various admin ports from one specific IP address or subnet. The wizard automatically detects the IP of
the client running the WUI and inserts this into the Admin IP field. The default mask is set to 255.255.255.0
which can be changed as required.

The firewall lockdown wizard uses two files:

• rc.lockdownwizard contains the script that can be changed

• rc.lockdownwizard.conf contains a set of variable definitions that is written automatically when

Update firewall lock down is clicked. The file depends on the rc.lockdownwizard script and the
load balancers configuration. This file should not be changed manually.

Chapter 5 – Appliance Management Page 64

 Appliance Administration Manual v8.1 Loadbalancer.org

When run, the script rc.lockdownwizard loads the settings from the definitions file rc.lockdownwizard.conf
and uses them to generate the rules. The web interface writes the definitions rc.lockdownwizard.conf.
You can modify rc.lockdownwizard via ssh or from the web interface using the Modify the firewall lock
down wizard script button. Apart from this link there is no other influence from the WUI.
The default script does not depend on the configured Virtual Services or Real Servers, so the wizard does
not need to be re-run when services are changed.
However, it does depend on the IP addresses of the master and slave, and the admin related ports used by
the web interface, heartbeat, and HAProxy. If those settings are changed, the firewall lockdown wizard will
need to be re-run in order to reflect the changes. Re-running the firewall lockdown wizard will adapt the
rc.lockdownwizard.conf definitions file automatically – any changes made to the script rc.lockdownwizard
will remain when you re-run the firewall lockdown wizard.

To run the lock-down wizard:

 In the WUI, open Maintenance > Firewall Lock Down Wizard

 The following screen will be displayed:

 Define your administration subnet/host in the Administration subnet field

N.B. Make sure that the subnet mask is correct – by default a /24 mask is used
N.B. To lock down access to a single host use <IP address>/32, e.g. 192.168.2.1/32

 Click Update firewall lock down

N.B. For a clustered pair, the lockdown wizard must be run on each appliance

Chapter 5 – Appliance Management Page 65

 Appliance Administration Manual v8.1 Loadbalancer.org

Disabling the lock-down script

To disable the lock-down script un-check the Enable lock down script check-box and click the Update
Firewall lock down button.
N.B. If you accidentally block your own access to the appliance you will need to clear the current firewall
rules and try again. to clear the firewall tables completely use the following command at the console:

/etc/rc.d/rc.flush-iptables

Conntrack Table Size

By default the connection tracking table size is set to 524288 and is fine in most cases. For high traffic
deployment using NAT mode, or when using connection tracking in the firewall script, this value may need
to be increased. If the connection tracking table fills up, the following error will be reported in the log:
ip_conntrack: table full, dropping packet.

To modify this setting:

 In the WUI, open Local Configuration > Physical – Advanced Configuration

 Use the following section:

 Set the required value using the Connection Tracking table size field

 Click Update

Users & Passwords

By default the appliance includes three pre-defined user accounts. The default usernames, passwords,
group membership and their primary use are:

Username Default Default Description (see also the group table below)
Password Group
appliance administration account
loadbalancer loadbalancer config *

viewing the appliance configuration, reports & logs

reportuser reportuser report

same as reportuser plus can also take servers on/off

maintuser maintuser maint line & create the support download archive file

* It's not possible to change the default group for user 'loadbalancer'

Chapter 5 – Appliance Management Page 66

 Appliance Administration Manual v8.1 Loadbalancer.org

N.B. These are Apache .htaccess style accounts and are not related to the local Linux OS level accounts.
The permissions for each group are shown below:

Menu / Permissions
System Local Cluster View
Group Maintenance Reports Logs Support
Overview configuration Configuration Configuration

config Full Full Full Full View Full View Full

report View None none None View Full View View

maint Full None None None View Full View Full

Modifying User Passwords

To modify a user's password:

 In the WUI, open Maintenance > Passwords

 In the following section, click the Modify button next to the relevant user

 Now change the password for the selected user:

 Click Edit User

Chapter 5 – Appliance Management Page 67

 Appliance Administration Manual v8.1 Loadbalancer.org

Adding New Users

To add new users:

 In the WUI, open Maintenance > Passwords

 Use the following section:

 Enter the required Username & Password and click Add New User

 By default, new users will be added to the report group (least privilege). To change this, click Modify
next to the user, select the required group and click Edit User

Resetting forgotten Passwords

It's possible to reset passwords via the command line if required. To do this you'll need to login as root to
the console / SSH session. The htpasswd command can then be used as shown below:

htpasswd -b /etc/loadbalancer.org/passwords loadbalancer <new password>

Appliance Security Lockdown Script

To ensure that the appliance is secure it's recommended that a number of steps should be carried out.
These steps have been incorporated into a lockdown script which can be run at the console
(recommended) or via an SSH session. The script helps to lock down the following:

 the password for the 'loadbalancer' Web User Interface account

 the password for the Linux 'root' account
 which subnet / host is permitted to access the load balancer

It also regenerates the SSH keys that are used to secure communicating between the master and slave
appliance. To start the script, at the console or via an SSH terminal session run the following command:

lbsecure

The image below illustrates how the script works for a single appliance:

Chapter 5 – Appliance Management Page 68

 Appliance Administration Manual v8.1 Loadbalancer.org

Once the script has finished, the “Security enhancement complete” message is displayed as shown
above.

NOTE : If lbsecure is run on the master of a correctly configured HA pair, the passwords,
firewall rules and SSH keys will also be updated on the slave appliance.

To reverse the action of lbsecure, the command ibinsecure can be used.

Chapter 5 – Appliance Management Page 69

 Appliance Administration Manual v8.1 Loadbalancer.org

SSH Keys
This menu option enables SSH keys to be managed.

NOTE : Normally this menu option will not be used because the keys are managed by the
Loadbalancer.org appliance and under normal circumstances do not require user
intervention.

To view / manage SSH keys:

 In the WUI, open Local Configuration > SSH Keys

The first tab (SSH Keys) enables the following keys to be viewed & managed:

Host Keys - the host identification key(s) of the local host

User Keys - the public key(s) of the user presented to remote hosts

The second tab (SSH Authentication) enables the following keys to be viewed & managed:

Host Keys (known_hosts) - the known key(s) of hosts that have been previously connected to or have
been pre-configured. In an HA pair you you will see the peer appliance keys.

User Keys (authorized_keys) - the public key(s) of remote hosts that can log in as the specified user. In an
HA pair you you will see the peer appliance keys.

Chapter 5 – Appliance Management Page 70

Appliance Administration Manual v8.1 Loadbalancer.org

Chapter 6 – Configuring Load Balanced Services

Chapter 6 – Configuring Load Balanced Services Page 71

 Appliance Administration Manual v8.1 Loadbalancer.org

Layer 4 Services
The Basics
Layer 4 services are based on LVS (Linux Virtual Server). LVS implements transport layer load balancing
inside the Linux kernel. It is used to direct requests for TCP/UDP based services to the Real Servers, and
makes services on the Real Servers appear as a Virtual Service on a single IP address.
Layer 4 services are transparent by default, i.e. the source IP address is maintained through the load
balancer.
Layer 4 persistence is based on source IP address & destination port. The time out value is in seconds and
each time the client makes a connection the timer is reset, so even a 5 minute persistence setting could
last for hours if the client is active and regularly refreshes their connection.
When a VIP is added the load balancer automatically adds a corresponding floating IP address which is
activated instantly. Check View Configuration > Network Configuration to ensure that the Floating IP
address has been activated correctly. They will show up as secondary addresses / aliases.
Multiple ports can be defined per VIP, for example 80 & 443. In this case it may also be useful to enable
persistence (aka affinity / stickiness) to ensure that clients hit the same back-end server for both HTTP &
HTTPS traffic and also prevent the client having to renegotiate the SSL connection.

NOTE : It's not possible to configure a VIP on the same IP address as any of the network
interfaces. this ensures that services can 'float' (move) between master and slave appliances.

Creating Virtual Services (VIPs)

Each Virtual Service can have an unlimited number of Real Servers (except the Enterprise R20 which is
limited to 5 x VIPs each with up to 4 RIPs). Typically you'll need one Virtual Service for each distinct cluster
(group of load balanced servers). Multiple ports can also be specified.

To add a new layer 4 VIP:

 In the WUI, open Cluster Configuration > Layer 4 – Virtual Services

 Click Add a new Virtual Service

 Enter an appropriate Label (name) for the new Virtual Service

 Enter the required IP address in the Virtual Service IP address field

 Enter the required port(s) in the Virtual Service Ports field, separate multiple ports with commas, specify
a range with a hyphen and specify all ports using an asterisk (*)

Chapter 6 – Configuring Load Balanced Services Page 72

 Appliance Administration Manual v8.1 Loadbalancer.org

NOTE : The following ports are used by the appliance and therefore cannot be used for
Virtual Services: 22 (SSH), 9080 (WUI – HTTP), 9443 (WUI – HTTPS), 7777 (HAProxy statistics
page), 7778 (HAProxy persistence table replication and 9081 (nginx fallback page).

 Set the Protocol as required

TCP – Transmission Control Protocol is the default and most common option
UDP – User Datagram Protocol – used for DNS, SIP, etc.
One Packet Scheduling - used for UDP SIP connections
Firewall Marks – For use when traffic has been tagged in the firewall script using the MARK target

 Select the required Forwarding Method

Direct Routing (DR) - This is the default one-arm mode. Direct Routing is recommended as it's easy to
understand and implement with two load balancers in failover mode (our recommended
configuration). It only requires one external Floating IP address on the same subnet as your web server
cluster and only one network card.
NAT – This is the default two-arm mode (Network Address Translation). This has the advantage that you
can load balance any device without having to deal with the ARP problem. The Real Servers need their
default gateway changed to be the internal floating VIP of the load balancer. Because the load balancer
handles the return packet you will get more detailed statistics but slower speed than DR or TUN. NAT
can also be implemented with a single NIC – just use the firewall script to set up an alias on the eth0
interface.
Tunneling – This is for WAN links (Tunneling). Tunneling has somewhat limited use as it requires an ip
tunnel between the load balancer and the Real Server as the VIP is the target address many routers will
drop the packet assuming that it has been spoofed. However it is useful for private networks with Real
Servers on multiple subnets.

 Click Update

 Now proceed to define the RIPs (Real Servers) as detailed on page 76

Modifying a Virtual Service

When first adding a Virtual Service, only certain settings can be configured, others are set at their default
setting. These values can be changed after the Virtual Service has been created by clicking Modify next to
the relevant Virtual Service. Additional settings that can be changed are:

Option Sub-Option Description

Balance Mode Weighted Least-Connection – assign more jobs to
servers with fewer jobs, relative to the Real Servers'
weight (the default).
Weighted Round Robin – assign jobs to Real
Servers proportionally to the Real Servers' weight.
Servers with higher weights receive new jobs first
and get more jobs than servers with lower weights.
Servers with equal weights get an equal distribution
of new jobs.
Destination Hash – assign jobs to servers through
looking up a statically assigned hash table by their
destination IP addresses.

Persistent Enable persistence for this Virtual Service, by Source

Chapter 6 – Configuring Load Balanced Services Page 73

Appliance Administration Manual v8.1 Loadbalancer.org

IP or SIP call-ID. Sticky or persistent connections are

required for some protocols such as FTP and SIP. It is
also kind to clients when using SSL, and
unfortunately sometimes required with HTTP if your
web application cannot keep state between Real
Servers.
N.B. If your Real Servers cannot keep session state
persistence themselves, then you will obtain
performance benefits from a load balancer, but may
not obtain reliability benefits.

Timeout How long do you want connections to be sticky?

The persistence time is in seconds and is reset on
every connection; i.e. 5 minutes persistence will last
for ever if the client clicks on a link within that
period.

Granularity Group IP addresses for the purposes of persistence.

Some large ISPs use clustered proxies, where the
clients' source IP address may change frequently. If
you require persistence with HTTP, this may cause a
problem. Setting a larger mask will associate a
subnet with a single persistence record. For
example, 255.255.255.0 specifies a whole class C
subnet.
The default is a single address, or 255.255.255.255.

Health Checks Specify the type of health check to be performed on

the Real Servers.

Check Type Specify the type of health check to be performed on

the Real Servers.

Negotiate – Scan the page specified in Request to

send, and check the returned data for the Response
expected string.

Connect to port – Attempt to make a connection

to the specified port.

Ping Server – Use a simple ICMP ping to perform

health checks.

External script – Use a custom file for the health

check. Specify the script path in the Check
Command field.

No checks, always off – all Real Servers are marked

offline.

No checks, always on – all Real Servers are marked

online.

5 Connects, 1 Negotiate – Repeating pattern of 5

Connect checks followed by 1 Negotiate check.

Chapter 6 – Configuring Load Balanced Services Page 74

Appliance Administration Manual v8.1 Loadbalancer.org

10 Connects, 1 Negotiate – Repeating pattern of

10 Connect checks followed by 1 Negotiate check.
Check Port If you want the Service to check to be say HTTPS
but not on the default port (443) then you can
specify that here.

External Script command The custom check script, used with the external
check type. The script should be placed in
/var/lib/loadbalancer.org/check, and given world
read and execute permissions.
Negotiate Check Related The options available depend on which protocol is
Options selected for the health-check.
Protocol Specify the protocol to use for negotiate health
checks. For common protocols, this will match the
Virtual Service port. Simple TCP may be used to
send an arbitrary string to the server, and match
against its response.
Virtual Host If the Negotiate check should be performed on a
specific Virtual Host, specify the hostname here.
Database Name The database to use for the MySQL Negotiate check.
This is a required option if MySQL is selected under
Negotiate Check Service above. There is no default.
Radius Secret Configure the RADIUS secret string for the RADIUS
negotiate check.
Login The login name to use with the Negotiate check
where authentication is required.
Password The password to use with the Negotiate check
where authentication is required.
Request to send With negotiate checks, the request to send to the
server. The use of this parameter varies with the
protocol selected in Service to Check.

With protocols such as HTTP and FTP, this should be

the object to request from the server. Bare file
names will be requested from the web or FTP root.

With DNS, this should be either a name to look up in

an A record, or an IP address to look up in a PTR
record.

With databases, this should be an SQL query.

With LDAP, this should be the search base for the
query. The load balancer will perform an (Object
Class=*) search relative to this base.

With Simple TCP, this should be a string to send

verbatim to the server.
Response expected This string will be matched against the response to a
negotiate check. If the string matches anywhere in
the response data, the negotiate check is considered
a success.

Chapter 6 – Configuring Load Balanced Services Page 75

 Appliance Administration Manual v8.1 Loadbalancer.org

Feedback Method The method the load balancer uses to measure to

performance of the Real Servers.
Agent – A simple telnet to port 3333 on the Real
Server.
HTTP – A simple HTTP GET to port 3333 on the
Real Server.
None – No feedback (default setting).
The loadbalancer expects a 0-99 integer response
from the agent, usually relating to the CPU idle; i.e. a
response of 92 would imply that the Real Servers
CPU is 92% idle. The load balancer will then use the
formula ((92 / 10) * requested_weight) to find the
new weight. Using this method an idle Real Server
will get 10 times as many new connections as an
overloaded server.

Fallback Server The server to route to if all of the Real Servers in the
group fail the health check. The local nginx fallback
server is configured for the ports 80 and 9081
(configured to always show the index.html page).
When using HAProxy Layer 7 the nginx server port
80 is automatically disabled. You can also configure
the fallback server to be a 'Hot Spare' if required.
For example you have one server in the cluster and
one fallback they will act as a master / slave pair.
IP Address Set the fallback server IP Address.
Port Set the fallback server port, for DR mode leave this
blank as it must be the same as the VIP.
MASQ Fallback Masquerade fallback. When enables, this enables the
fallback server to be set as a Layer 7 Virtual Service.
This is especially useful in WAN/DR site
environments.
Email Alert Destination Destination email address for server health-check
Address notifications.

NOTE : For more details on configuring health-checks please refer to chapter 8 on page 164

Creating Real Servers (RIPs)

You can add an unlimited number of Real Servers to each Virtual Service (except the Enterprise R20 which
is limited to 5 x VIPs each with up to 4 RIPs). In DR mode, since port redirection is not possible the Real
Server port field is not available and the port is automatically set to be the same as the Virtual Service,
whilst for a NAT mode Real Server, it's possible to configure the port to be the same or different to the
Virtual Service's port.
To add a new layer 4 RIP:

 In the WUI, open Cluster Configuration > Layer 4 – Real Servers

Chapter 6 – Configuring Load Balanced Services Page 76

Appliance Administration Manual v8.1 Loadbalancer.org

 Click Add a new Real Server next to the relevant Virtual Service

 Enter an appropriate Label (name) for the new Real Server

 Enter the required IP address in the Real Server IP Address field

 Enter the required port in the Real Server Port field. This only applies to NAT mode, in DR mode port
redirection is not possible so by default the port is the same as defined in the VIP

 Specify the required Weight, the is an integer specifying the capacity of a server relative to the others in
the pool, the valid values of weight are 0 through to 65535, the default is 100. The higher the value, the
more connections the server will receive

 Specify the Minimum Connections, this is an integer specifying the lower connection threshold of a
server. The valid values are 0 through to 65535. The default is 0, which means the lower connection
threshold is not set
If Minimum Connections is set with other values, the server will receive new connections when the
number of its connections drops below its lower connection threshold. If Minimum Connections is not
set but Maximum Connections is set, the server will receive new connections when the number of its
connections drops below three fourths of its upper connection threshold

 Specify the Maximum Connections, this is an integer specifying the upper connection threshold of a
server. The valid values of Maximum Connections are 0 through to 65535. The default is 0, which
means the upper connection threshold is not set

Chapter 6 – Configuring Load Balanced Services Page 77

 Appliance Administration Manual v8.1 Loadbalancer.org

Persistence Considerations

Persistence State Table Replication

If you want the current persistent connection table to work when the active appliance (typically the
master) swaps over to the passive appliance (typically the slave appliance) then you can start the
synchronization daemons on each load balancer to replicate the data in real time as detailed below.

First login to the master appliance using SSH or at the console, then as root run the following commands:

ipvsadm --start-daemon master

ipvsadm --start-daemon backup

Then login to the slave appliance using SSH or at the console, then as root run the following commands:

ipvsadm --start-daemon master

ipvsadm --start-daemon backup

N.B. To ensure that these sync daemons are started on each reboot put these commands in the rc.firewall.
This can be done via the WUI using Maintenance > Firewall Script. Make sure that the full path is specified
in the firewall script, i.e.

/usr/local/sbin/ipvsadm --start-daemon master

/usr/local/sbin/ipvsadm --start-daemon backup

After a few seconds you can confirm that it is working by seeing the output from:

ipvsadm -Lc

N.B. This is the same command that the 'Layer 4 Current Connections' report is based on.

When run on the active device the output will show all connections including those in state 'NONE' i.e. the
persistence entries. When run on the passive device, the output will only include connections in state
'NONE' since only these are being replicated.

To stop the replication, run the following commands on both appliance's:

ipvsadm --stop-daemon master

ipvsadm --stop-daemon backup

NOTE : Setting this option can generate a high level traffic between the master and slave
appliances.

NOTE : Once configured, you'll see multicast traffic from the active appliance on IP address
224.0.0.81 , port 8848.

Chapter 6 – Configuring Load Balanced Services Page 78

 Appliance Administration Manual v8.1 Loadbalancer.org

DR Mode Considerations

The ARP Problem

DR mode works by changing the MAC address of the inbound packets to match the Real Server selected
by the load balancing algorithm. To enable DR mode to operate:

• Each Real Server must be configured to accept packets destined for both the VIP address and the
Real Servers IP address (RIP). This is because in DR mode the destination address of load balanced
packets is the VIP address, whilst for other traffic such as health-checks, administration traffic etc.
it's the Real Server's own IP address (the RIP). The service/process (e.g. IIS) must also respond to
both addresses.
• Each Real Server must be configured so that it does not respond to ARP requests for the VIP
address – only the load balancer should do this.

Configuring the Real Servers in this way is referred to as 'Solving the ARP problem''. The steps required
depend on the OS used as detailed in the following sections.

Detecting the ARP Problem

Attempt to connect to the VIP and then use Reports > Layer 4 Current Connections to check whether the
connection state is SYN_RECV as shown below. If it is, this is normally a good indication that the ARP
problem has not been correctly solved.

Solving the ARP Problem for Linux

Method 1 (using iptables)

You can use iptables (netfilter) on each Real Server to re-direct incoming packets destined for the Virtual
Service IP address. To make this permanent, simply add the command to an appropriate start-up script
such as /etc/rc.local. If the Real Server is serving multiple VIPs, add additional iptables rules for each VIP.

iptables -t nat -A PREROUTING -p tcp -d <VIP> -j REDIRECT

e.g.

iptables -t nat -A PREROUTING -p tcp -d 10.0.0.21 -j REDIRECT

(Change the IP address to be the same as your Virtual Service)

This means redirect any incoming packets destined for 10.0.0.21 (the Virtual Service) locally, i.e. to the
primary address of the incoming interface on the Real Server.

Chapter 6 – Configuring Load Balanced Services Page 79

 Appliance Administration Manual v8.1 Loadbalancer.org

NOTE : Method 1 may not always be appropriate if you're using IP-based virtual hosting on
your web server. This is because the iptables rule above redirects incoming packets to the
primary address of the incoming interface on the web server rather than any of the virtual
hosts that are configured. Where this is an issue, use method 2 below instead.

Also, Method 1 does not work with IPv6 Virtual Services, use method 2 below instead.

Method 2 (using arp_ignore sysctl values)

This is the preferred method as it supports both IPv4 and IPv6. Each Real Server needs the loopback
adapter to be configured with the Virtual Services IP address. This address must not respond to ARP
requests and the web server also needs to be configured to respond to this address. To set this up follow
steps 1-4 below.

Step 1: re-configure ARP on the Real Servers (this step can be skipped for IPv6 Virtual Services)

To do this add the following lines to /etc/sysctl.conf:

net.ipv4.conf.all.arp_ignore=1
net.ipv4.conf.eth0.arp_ignore=1
net.ipv4.conf.eth1.arp_ignore=1
net.ipv4.conf.all.arp_announce=2
net.ipv4.conf.eth0.arp_announce=2
net.ipv4.conf.eth1.arp_announce=2

Step 2: re-configure DAD on the Real Servers (this step can be skipped for IPv4 Virtual Services)

net.ipv6.conf.lo.dad_transmits=0
net.ipv6.conf.lo.accept_dad=0

Step 3: apply these settings

Either reboot the Real Server or run the following command to apply these settings:

/sbin/sysctl -p

Step 4: add the Virtual Services IP address to the loopback adapter

Run the following command for each VIP. To make this permanent, simply add the command to an
appropriate startup script such as /etc/rc.local.

ip addr add dev lo <IPv4-VIP>/32

for IPv6 addresses use:

ip addr add dev lo <IPv6-VIP>/128

Chapter 6 – Configuring Load Balanced Services Page 80

 Appliance Administration Manual v8.1 Loadbalancer.org

N.B. Steps 1, 2 & 3 can be replaced by writing directly to the required files using the following commands:
(temporary until the next reboot)

echo 1 > /proc/sys/net/ipv4/conf/all/arp_ignore

echo 1 > /proc/sys/net/ipv4/conf/eth0/arp_ignore
echo 1 > /proc/sys/net/ipv4/conf/eth1/arp_ignore
echo 2 > /proc/sys/net/ipv4/conf/all/arp_announce
echo 2 > /proc/sys/net/ipv4/conf/eth0/arp_announce
echo 2 > /proc/sys/net/ipv4/conf/eth1/arp_announce
echo 0 > /proc/sys/net/ipv6/conf/lo/dad_transmits
echo 0 > /proc/sys/net/ipv6/conf/lo/accept_dad

Solving the ARP Problem for Solaris

With Solaris the loopback interface does not respond to ARP requests so you just add your VIPs to it.

ifconfig lo0:1 plumb

ifconfig lo0:1 VIP netmask 255.255.255.255 up

You will need to add this to the startup scripts for your server.

Solving the ARP Problem for Mac OS X / BSD

OS X is BSDish, so you need to use BSDish syntax:

ifconfig lo0 alias VIP netmask 255.255.255.255 -arp up

You will need to add this to the startup scripts for your server.

NOTE : Don't forget that the service on the Real Servers needs to listen on both the RIP
address and VIP address as mentioned previously.

NOTE : Failure to correctly configure the Real Servers to handle the ARP problem is the most
common mistake in DR mode configurations.

Chapter 6 – Configuring Load Balanced Services Page 81

 Appliance Administration Manual v8.1 Loadbalancer.org

Solving the ARP Problem for Windows Servers

Windows Server 2000

Windows Server 2000 supports the direct routing (DR) method through the use of the MS Loopback
Adapter to handle the traffic. The IP address on the Loopback Adapter must be set to be the same as the
Virtual Services IP address (VIP). If the Real Server is included in multiple VIPs, you can add additional IP
addresses to the Loopback Adapter that correspond to each VIP.

Step 1: Install the Microsoft Loopback Adapter

1. Open the Control Panel and double-click Add/Remove Hardware

2. Once the Hardware Wizard opens, click Next

3. Select Add/Troubleshoot a device, click Next

4. Once the device list appears, select Add a new device at the top of the list, click Next

5. Select No, I want to select the hardware from a list, click Next

6. Scroll down the list and select Network Adapters, click Next

7. Select Microsoft & Microsoft Loopback Adapter, click Next as shown below

8. Click Next to start the installation, when complete click Finish

Step 2: Configure the Loopback Adapter

Chapter 6 – Configuring Load Balanced Services Page 82

Appliance Administration Manual v8.1 Loadbalancer.org

1. Open the Control Panel and double-click Network and Dial-up Connections

2. Right-click the new Loopback Adapter and select Properties

3. Un-check all items except Internet Protocol (TCP/IP) as shown below

4. Select Internet Protocol (TCP/IP), click Properties and configure the IP address and mask to be
the same as the Virtual Service IP address (VIP), e.g. 192.168.2.20/24 as shown below

5. Click Advanced and change the Interface metric to 254 as shown below, this prevents the

Chapter 6 – Configuring Load Balanced Services Page 83

Appliance Administration Manual v8.1 Loadbalancer.org

adapter responding to ARP requests for the VIP address

6. Click OK on Advanced Settings, TCP/IP Properties and Connection Properties to save and apply
the new settings

7. Repeat the above steps for all other Windows 2000 Real Servers

Chapter 6 – Configuring Load Balanced Services Page 84

 Appliance Administration Manual v8.1 Loadbalancer.org

Windows Server 2003

Windows server 2003 supports the direct routing (DR) method through the use of the MS Loopback
Adapter to handle the traffic. The IP address on the Loopback Adapter must be set to be the same as the
Virtual Services IP address (VIP). If the Real Server is included in multiple VIPs, you can add additional IP
addresses to the Loopback Adapter that correspond to each VIP.

Step 1: Install the Microsoft Loopback Adapter

1. Open the Control Panel and double-click Add Hardware

2. Once the Hardware Wizard opens, click Next

3. Select Yes, I have already connected the hardware, click Next

4. Scroll to the bottom of the list, select Add a new hardware device, click Next

5. Select Install the hardware that I manually select from a list (Advanced), click Next

6. Select Network adapters, click Next

7. Select Microsoft & Microsoft Loopback Adapter, click Next as shown below

8. Click Next to start the installation, when complete click Finish

Chapter 6 – Configuring Load Balanced Services Page 85

 Appliance Administration Manual v8.1 Loadbalancer.org

Step 2: Configure the Loopback Adapter

1. Open the Control Panel and double-click Network Connections

2. Right-click the new Loopback Adapter and select Properties

3. Un-check all items except Internet Protocol (TCP/IP) as shown below

4. Select Internet Protocol (TCP/IP), click Properties and configure the IP address and mask to be
the same as the Virtual Service (VIP), e.g. 192.168.2.20/24 as shown below

Chapter 6 – Configuring Load Balanced Services Page 86

Appliance Administration Manual v8.1 Loadbalancer.org

5. Click Advanced, un-check Automatic metric and change Interface metric to 254 as shown
below, this prevents the adapter responding to ARP requests for the VIP address

6. Click OK on Advanced Settings & TCP/IP Properties, then click Close on Connection Properties to
save and apply the new settings

7. Now repeat the above process for all other Windows 2003 Real Servers

Chapter 6 – Configuring Load Balanced Services Page 87

 Appliance Administration Manual v8.1 Loadbalancer.org

Windows Server 2008

The basic concept is the same as for Windows 2000 / 2003. However, additional steps are required to set
the strong / weak host behavior. This is used to either block or allow interfaces receiving packets destined
for a different interface on the same server. As with Windows 2000 / 2003, if the Real Server is included in
multiple VIPs, you can add additional IP addresses to the Loopback Adapter that correspond to each VIP.

Step 1: Install the Microsoft Loopback Adapter

1. Click Start, then run hdwwiz to start the Hardware Installation Wizard

2. When the Wizard has started, click Next

3. Select Install the hardware that I manually select from a list (Advanced) , click Next

4. Select Network adapters , click Next

5. Select Microsoft & Microsoft Loopback Adapter, click Next

6. Click Next to start the installation, when complete click Finish

Step 2: Configure the Loopback Adapter

1. Open Control Panel and click View Network status and tasks under Network and internet
2. Click Change adapter settings
3. Right-click the new Loopback Adapter and select Properties

Chapter 6 – Configuring Load Balanced Services Page 88

Appliance Administration Manual v8.1 Loadbalancer.org

4. Un-check all items except Internet Protocol Version 4 (TCP/IPv4) and Internet Protocol Version
6 (TCP/IPv6) as shown below
N.B. leaving both checked ensures that both IPv4 and IPv6 are supported. If preferred, only the
protocol to be used can be checked

5. If configuring IPv4 addresses select Internet Protocol Version (TCP/IPv4), click Properties and
configure the IP address to be the same as the Virtual Service (VIP) with a subnet mask of
255.255.255.255 , e.g. 192.168.2.20 / 255.255.255.255 as shown below

6. If configuring IPv6 addresses select Internet Protocol Version (TCP/IPv6), click Properties and
configure the IP address to be the same as the Virtual Service (VIP) and set the Subnet Prefix
Length to be the same as your network setting , e.g. 2001:470:1f09:e72::15 / 64 as shown below

Chapter 6 – Configuring Load Balanced Services Page 89

 Appliance Administration Manual v8.1 Loadbalancer.org

7. Click OK, then click Close to save and apply the new settings

8. Now repeat the above process on the other Windows 2008 Real Servers

N.B. For Windows 2008, it's not necessary to modify the interface metric on the advanced tab and
should be left set to Automatic

Step 3: Configure the strong / weak host behavior

Windows Server 2000 and Windows Server 2003 use the weak host model for sending and receiving for all
IPv4 interfaces and the strong host model for sending and receiving for all IPv6 interfaces. You cannot
configure this behavior.
The Next Generation TCP/IP stack in Windows 2008 and later supports strong host sends and receives for
both IPv4 and IPv6 by default. To ensure that Windows 2008 is running in the correct mode to be able to
respond to the VIP, the following commands must be run on each Real Server:

For IPv4 addresses :

netsh interface ipv4 set interface "net" weakhostreceive=enabled

netsh interface ipv4 set interface "loopback" weakhostreceive=enabled
netsh interface ipv4 set interface "loopback" weakhostsend=enabled

For these commands to work, the LAN connection NIC must be named “net” and the loopback NIC must
be named “loopback” as shown below. If you prefer to leave your current NIC names, then the commands
above must be modified accordingly. For example, if your network adapters are named “LAN” and
“LOOPBACK”, the commands required would be:

netsh interface ipv4 set interface "LAN" weakhostreceive=enabled

netsh interface ipv4 set interface "LOOPBACK" weakhostreceive=enabled
netsh interface ipv4 set interface "LOOPBACK" weakhostsend=enabled

Chapter 6 – Configuring Load Balanced Services Page 90

 Appliance Administration Manual v8.1 Loadbalancer.org

For IPv6 addresses :

netsh interface ipv6 set interface "net" weakhostreceive=enabled

netsh interface ipv6 set interface "loopback" weakhostreceive=enabled
netsh interface ipv6 set interface "loopback" weakhostsend=enabled
netsh interface ipv6 set interface "loopback" dadtransmits=0

For these commands to work, the LAN connection NIC must be named “net” and the loopback NIC must
be named “loopback” as shown below. If you prefer to leave your current NIC names, then the commands
above must be modified accordingly. For example, if your network adapters are named “LAN” and
“LOOPBACK”, the commands required would be:

netsh interface ipv6 set interface "LAN" weakhostreceive=enabled

netsh interface ipv6 set interface "LOOPBACK" weakhostreceive=enabled
netsh interface ipv6 set interface "LOOPBACK" weakhostsend=enabled
netsh interface ipv6 set interface "LOOPBACK" dadtransmits=0

N.B. The names for the NICs are case sensitive, so make sure that the name used for the interface and the
name used in the commands match exactly.

1. Start Powershell or use a command window to run the appropriate netsh commands as shown in
the example below

N.B. This shows an IPv6 example, use the IPv4 commands if you're using IPv4 addresses

2. Now repeat these 4 commands on the other Windows 2008 Real Servers

Chapter 6 – Configuring Load Balanced Services Page 91

 Appliance Administration Manual v8.1 Loadbalancer.org

Windows Server 2012

The basic concept is the same as for Windows 2000 / 2003. However, additional steps are required to set
the strong / weak host behavior. This is used to either block or allow interfaces receiving packets destined
for a different interface on the same server. As with Windows 2000 / 2003 / 2008, if the Real Server is
included in multiple VIPs, you can add additional IP addresses to the Loopback Adapter that correspond to
each VIP.

Step 1: Install the Microsoft Loopback Adapter

1. Click Start, then run hdwwiz to start the Hardware Installation Wizard

2. When the Wizard has started, click Next

3. Select Install the hardware that I manually select from a list (Advanced) , click Next

4. Select Network adapters , click Next

5. Select Microsoft & Microsoft KM-Test Loopback Adapter, click Next

6. Click Next to start the installation, when complete click Finish

Step 2: Configure the Loopback Adapter

1. Open Control Panel and click Network and Sharing Center

2. Click Change adapter settings

3. Right-click the new Loopback Adapter and select Properties

Chapter 6 – Configuring Load Balanced Services Page 92

Appliance Administration Manual v8.1 Loadbalancer.org

4. Un-check all items except Internet Protocol Version 4 (TCP/IPv4) and Internet Protocol Version
6 (TCP/IPv6) as shown below
N.B. leaving both checked ensures that both IPv4 and IPv6 are supported. If preferred, only the
protocol to be used can be checked

5. If configuring IPv4 addresses select Internet Protocol Version (TCP/IPv4), click Properties and
configure the IP address to be the same as the Virtual Service (VIP) with a subnet mask of
255.255.255.255 , e.g. 192.168.2.20 / 255.255.255.255 as shown below

6. If configuring IPv6 addresses select Internet Protocol Version (TCP/IPv6), click Properties and
configure the IP address to be the same as the Virtual Service (VIP) and set the Subnet Prefix
Length to be the same as your network setting , e.g. 2001:470:1f09:e72::15 / 64 as shown below

Chapter 6 – Configuring Load Balanced Services Page 93

 Appliance Administration Manual v8.1 Loadbalancer.org

7. Click OK on TCP/IP Properties, then click Close on Ethernet Properties to save and apply the new
settings

8. Now repeat the above process on the other Windows 2012 Real Servers

N.B. For Windows 2012, it's not necessary to modify the interface metric on the advanced tab and
should be left set to Automatic

Step 3: Configure the strong / weak host behavior

Windows Server 2000 and Windows Server 2003 use the weak host model for sending and receiving for all
IPv4 interfaces and the strong host model for sending and receiving for all IPv6 interfaces. You cannot
configure this behavior.
The Next Generation TCP/IP stack in Windows 2008 and later supports strong host sends and receives for
both IPv4 and IPv6 by default. To ensure that Windows 2012 is running in the correct mode to be able to
respond to the VIP, the following commands must be run on each Real Server:

For IPv4 addresses :

netsh interface ipv4 set interface "net" weakhostreceive=enabled

netsh interface ipv4 set interface "loopback" weakhostreceive=enabled
netsh interface ipv4 set interface "loopback" weakhostsend=enabled

For these commands to work, the LAN connection NIC must be named “net” and the loopback NIC must
be named “loopback” as shown below. If you prefer to leave your current NIC names, then the commands
above must be modified accordingly. For example, if your network adapters are named “LAN” and
“LOOPBACK”, the commands required would be:
netsh interface ipv4 set interface "LAN" weakhostreceive=enabled
netsh interface ipv4 set interface "LOOPBACK" weakhostreceive=enabled
netsh interface ipv4 set interface "LOOPBACK" weakhostsend=enabled

Chapter 6 – Configuring Load Balanced Services Page 94

 Appliance Administration Manual v8.1 Loadbalancer.org

For IPv6 addresses :

netsh interface ipv6 set interface "net" weakhostreceive=enabled

netsh interface ipv6 set interface "loopback" weakhostreceive=enabled
netsh interface ipv6 set interface "loopback" weakhostsend=enabled
netsh interface ipv6 set interface "loopback" dadtransmits=0

For these commands to work, the LAN connection NIC must be named “net” and the loopback NIC must
be named “loopback” as shown below. If you prefer to leave your current NIC names, then the commands
above must be modified accordingly. For example, if your network adapters are named “LAN” and
“LOOPBACK”, the commands required would be:

netsh interface ipv6 set interface "LAN" weakhostreceive=enabled

netsh interface ipv6 set interface "LOOPBACK" weakhostreceive=enabled
netsh interface ipv6 set interface "LOOPBACK" weakhostsend=enabled
netsh interface ipv6 set interface "LOOPBACK" dadtransmits=0

N.B. The names for the NICs are case sensitive, so make sure that the name used for the interface and the
name used in the commands match exactly.

1. Start Powershell or use a command window to run the appropriate netsh commands as shown in
the example below

N.B. This shows an IPv6 example, use the IPv4 commands if you're using IPv4 addresses

2. Now repeat these 4 commands on the other Windows 2012 Real Servers

Chapter 6 – Configuring Load Balanced Services Page 95

 Appliance Administration Manual v8.1 Loadbalancer.org

Verifying netsh Settings for Windows 2008 & 2012

To verify that settings have been configured correctly, run the following command on each Real Server to
clearly list the settings that have been applied to the interface:

netsh interface ipv4 show interface <interface name>

i.e.

for the 'loopback' adapter run: netsh interface ipv4 show interface loopback

for the 'net' adapter run: netsh interface ipv4 show interface net

(N.B. For IPv6, simply replace 'ipv4' with 'ipv6' in the above commands)

e.g.

This shows that the settings have been applied correctly.

NOTE : For Windows server 2008 / 2012, if you want to leave the built-in firewall enabled,
you'll either need to enable the relevant default firewall exceptions or create your own to
enable access to the web server. By default these exceptions will allow traffic on both the
network and loopback adapters.

NOTE : Failure to correctly configure the Real Servers to handle the ARP problem is the most
common problem in DR configurations.

Chapter 6 – Configuring Load Balanced Services Page 96

 Appliance Administration Manual v8.1 Loadbalancer.org

Configuring IIS to Respond to both the RIP and VIP

For DR & TUN modes, it's also important to make sure that your application (IIS in this case) responds to
both the VIP and RIP.

Windows 2000 / 2003

By default, IIS listens on all configured IP addresses, this is shown in the example below (shows Windows
2003 example). As can be seen the IP address field is set to 'All Unassigned'.

If the default configuration is left, no further IIS configuration is required. If you do change the IP address in
the bindings from 'All Unassigned' to a specific IP address, then you need to make sure that you also add a
binding for the Virtual Service IP address (VIP) as shown in the example below:

NOTE : These examples illustrates how IIS must be configured to ensure that its listening on
both the RIP and VIP address. It's important to remember that this applies equally to all
applications when running in DR mode.

Chapter 6 – Configuring Load Balanced Services Page 97

 Appliance Administration Manual v8.1 Loadbalancer.org

Windows 2008 / 2012

By default, IIS listens on all configured IP addresses, this is shown in the example below (shows Windows
2008 example). As can be seen the IP address field is set to “All Unassigned”.

If the default configuration is left, no further IIS configuration is required. If you do change the IP address in
the bindings from “All Unassigned” to a specific IP address, then you need to make sure that you also add a
binding for the Virtual Service IP address (VIP) as shown in the example below:

NOTE : These examples illustrates how IIS must be configured to ensure that its listening on
both the RIP and VIP address. It's important to remember that this applies equally to all
applications when running in DR mode.

Chapter 6 – Configuring Load Balanced Services Page 98

 Appliance Administration Manual v8.1 Loadbalancer.org

Windows Firewall Settings

Windows 2003 SP1+

For Windows Server 2003 SP1 & later, if you have enabled the built-in firewall, you will need to enable the
Web Server (HTTP) exception to permit access to the web server. This exception is created automatically
when IIS is installed and when enabled allows traffic on both the network and Loopback Adapters.

Windows 2008 R1 Firewall Settings

For Windows 2008 R1 the firewall configuration is very similar to windows 2003 R2. Again, an exception is
created automatically that must be enabled to permit port 80 HTTP traffic. You just need to enable
the firewall for both interfaces then ensure that the WWW service check-box is ticked as shown below:

Chapter 6 – Configuring Load Balanced Services Page 99

 Appliance Administration Manual v8.1 Loadbalancer.org

Windows 2008 R2 Firewall Settings

Windows 2008 automatically creates several default firewall rules for both inbound and outbound traffic.
There are 3 firewall profiles and interfaces can be associated with one of these 3 profiles (domain, private
and public) although the Loopback Adapter automatically gets associated with the public profile and this
cannot be changed.

For a web server listening on port 80 the following default HTTP rules need to be enabled as shown
below:

Windows 2012 Firewall Settings

Windows 2012 is very similar to Windows 2008 R2 as shown below.

Chapter 6 – Configuring Load Balanced Services Page 100

 Appliance Administration Manual v8.1 Loadbalancer.org

NAT Mode Considerations

NAT mode load balancing has the advantage that the only change required to the Real Servers is to modify
the default gateway and possibly the IP address and subnet. Whilst NAT mode is fairly straight forward, a
few points need to be considered.

NAT Mode Potential Issues

1. By default your Real Servers won't be able to access the Internet through the new default gateway
(except when replying to requests made through the external VIP).

2. Non-load balanced services on the Real Servers (e.g. RDP for management access to Windows
servers) will not be accessible since these have not been exposed via the load balancer

Enabling Real Server Internet access using Auto-NAT

To enable Auto-NAT:

 In the WUI, open Cluster Configuration > Layer 4 – Advanced Configuration

 Change Auto-NAT from off to the external interface being used – typically eth1

 Click Update

This activates the rc.nat script that forces external network traffic to be MASQUERADED to and from the
external network. The iptables masquerade rule that's used for this is shown below:

iptables -t nat -A POSTROUTING -o eth1 -j MASQUERADE

Enabling Access to non Load-Balanced Services

If you want specific services to be exposed on your Real Servers you have two choices:

 Setup a Virtual Service with a single Real Server for each service
or

 Setup a floating IP address and individual SNAT/DNAT rules for each service as shown in the example
below. These lines can be added to the firewall script using the WUI option Maintenance > Firewall
Script

INT_ADDR="10.50.110.238"
EXT_ADDR="192.168.111.250"

iptables -t nat -A POSTROUTING -p tcp -s $INT_ADDR -j SNAT --to-source $EXT_ADDR

iptables -t nat -A PREROUTING -p tcp -d $EXT_ADDR -j DNAT --to-destination $INT_ADDR

Chapter 6 – Configuring Load Balanced Services Page 101

 Appliance Administration Manual v8.1 Loadbalancer.org

Once the above SNAT/DNAT rules have been configured, the following firewall entries will be listed under
View Configuration > Firewall Rules

Chain PREROUTING (policy ACCEPT 524 packets, 123K bytes)

pkts bytes target prot opt in out source destination
2 104 DNAT tcp -- * * 0.0.0.0/0 192.168.111.250 to:10.50.110.238

Chain POSTROUTING (policy ACCEPT 80 packets, 4896 bytes)

pkts bytes target prot opt in out source destination
0 0 SNAT tcp -- * * 10.50.110.238 0.0.0.0/0 to:192.168.111.250

N.B If Autonat is already enabled, only the DNAT rule (i.e. not the SNAT rule) will be required.

NOTE : Please don't hesitate to contact [email protected] to discuss any specific

requirements you may have.

One-Arm (Single Subnet) NAT Mode

Normally the VIP is located on a different subnet to the Real Servers.

However, it is possible to perform NAT mode load balancing on a single subnet. Here, the VIP is brought
up in the same subnet as the Real Servers. For clients located on this subnet, return traffic would normally
be sent directly to the client bypassing the load balancer which would break NAT mode. To address this,
the routing table on the Real Servers must be modified to force return traffic to go via the load balancer.

The sections below explain how routing must be modified for Windows hosts and Linux hosts.

Route Configuration for Windows Servers

To rectify this issue for Windows servers, a route must be added to each server that takes priority over the
default Windows routing rules.
This is a simple case of deleting the default route and adding a permanent route via the load balancer as
shown below:

route delete 192.168.2.0 mask 255.255.255.0

route add -p 192.168.2.0 mask 255.255.255.0 192.168.2.21 metric 1

or using netsh commands:

netsh interface ipv4 delete route 192.168.2.0/24 "LAN"

netsh interface ipv4 add route 192.168.2.0/24 "LAN" 192.168.2.21

N.B. Replace 192.168.2.0 with your local subnet address

N.B. Replace 192.168.2.21 with the IP address of your load balancer
N.B. Replace “LAN” with the name of your Interface

This replaces the default route with a new route which goes via the loadbalancer.
Any local traffic (same subnet) is handled by this route and any external traffic is handled by the default
route (which also points at the load balancer).

Chapter 6 – Configuring Load Balanced Services Page 102

 Appliance Administration Manual v8.1 Loadbalancer.org

Route Configuration for Linux Servers

To rectify this issue for Linux servers, we need to modify the local network route by changing to a higher
metric:

route del -net 192.168.2.0 netmask 255.255.255.0 dev eth0

route add -net 192.168.2.0 netmask 255.255.255.0 metric 2000 dev eth0

Then we need to make sure that local network access uses the load balancer as its default route:

route add -net 192.168.2.0 netmask 255.255.255.0 gateway 192.168.2.21 metric 0 dev eth0

N.B. Replace 192.168.2.21 with the IP address of your load balancer

Any local traffic (same subnet) is then handled by this manual route and any external traffic is handled by
the default route (which also points at the load balancer).

Firewall Marks
Using firewall marks enables multiple ports and/or multiple IP addresses to be combined into a single
Virtual Service. A common use of this feature is to aggregate port 80 (HTTP) and port 443 (HTTPS) so that
when a client fills their shopping cart on via HTTP, then move to HTTPS to give their credit card
information, they will remain on the same Real Server.

Firewall Marks – Auto Configuration

When defining a layer 4 VIP with multiple ports, firewall marks are used automatically in the background to
enable this functionality. For example, to configure an HTTP & HTTPS NAT mode Virtual Service, port 80 &
443 must be specified separated by a comma in the 'Virtual Service Ports' field as shown below:

This will automatically configure the load balancer for firewall marks.

N.B. Persistence will be enabled automatically

Chapter 6 – Configuring Load Balanced Services Page 103

 Appliance Administration Manual v8.1 Loadbalancer.org

For NAT mode VIPs, leave the Real Server port blank as shown below:

Packets will then be forwarded to the Real Servers on the same port as it was received at the VIP.

N.B. For Layer 4 DR mode VIPs, there is no Real Server Port field since port translation is not possible in this
mode and packets will be forwarded to the same port as specified for the VIP

NOTE : To create an auto firewall mark VIP that listens on all ports, simply specify * in the
ports field rather than a specific port number.

NOTE : The heath check port is automatically set to be the first port in the list, e.g. if ports 80
& 443 are defined for the VIP, the check port is automatically set to port 80. This can be
changed if required using the Check Port field.

Firewall Marks – Manual Configuration

Firewall Marks can also be configured manually. This may be required for example when both TCP and
UDP are needed for a particular VIP. The basic concept is to create a firewall rule that matches incoming
packets to a particular IP address / port(s) and mark them with an arbitrary integer. A Virtual Service is also
configured specifying this firewall mark integer instead of the IP address.

EXAMPLE 1 – Setup a new DR Mode Firewall Mark when no Initial VIP has been Created

Step 1: Create the New VIP

 Using the WUI, go to Cluster Configuration > Layer 4 – Virtual Services

 Click Add a new Virtual Service
 Define the required Label (name) for the VIP
 Instead of entering an IP address, enter a numeric value representing the 'mark' as shown below, e.g. 1

Chapter 6 – Configuring Load Balanced Services Page 104

 Appliance Administration Manual v8.1 Loadbalancer.org

 Leave the Virtual Service Ports field blank (the ports will be defined in the firewall script in step 5 below)
 Set Protocol to Firewall Marks
 Set the Forwarding Method to Direct Routing
 Click Update

N.B. Persistence will be enabled automatically

Step 2: Define a Health-Check Port

 Using the WUI, go to Cluster Configuration > Layer 4 – Virtual Services

 Click Modify next to the new Virtual Service
 Enter the appropriate value in the Check Port field
 Click Update

Step 3: Add the Real Servers

 Using the WUI, go to Cluster Configuration > Layer 4 – Real Servers

 Click Add a new Real Server
 Enter the required details as shown below

 Click Update

Chapter 6 – Configuring Load Balanced Services Page 105

 Appliance Administration Manual v8.1 Loadbalancer.org

Step 4: Add the Associated Floating IP Address for the VIP

 Using the WUI, go to Cluster Configuration > Floating IPs

 Add a floating IP that corresponds to the required VIP, in this example 192.168.111.240

 Click Add Floating IP

Step 5: Modify the Firewall Script

 Using the WUI, go to Maintenance > Firewall Script

 Add the following, as shown below:

VIP1="192.168.111.240"
iptables -t mangle -A PREROUTING -p tcp -d $VIP1 --dport 8025 -j MARK --set-mark 1
iptables -t mangle -A PREROUTING -p udp -d $VIP1 --dport 8025 -j MARK --set-mark 1

 Click Update
 If using a clustered pair, make the same changes to the firewall script (i.e. step 5) on the slave unit.

*** The VIP is now configured and will be accessible on 192.168.111.240 , TCP & UDP port 8025 ***

Chapter 6 – Configuring Load Balanced Services Page 106

 Appliance Administration Manual v8.1 Loadbalancer.org

EXAMPLE 2 – Setup a Firewall Mark by Modifying an Existing VIP

In this case, the floating IP address associated with the VIP will already exist so does not need to be created
manually.

Step 1: Modify the Existing Virtual Service

 Using the WUI, go to Cluster Configuration > Layer 4 – Virtual Services

 Click Modify next to the relevant VIP

 Change the IP address to the chosen 'mark' value as shown above

 Clear the Virtual Service Ports field
 Set the Protocol field to Firewall Marks
 Click Update

Step 2: Define a Health-Check Port

 Using the WUI, go to Cluster Configuration > Layer 4 – Virtual Services

 Click Modify next to the new Virtual Service
 Enter the appropriate value in the Check Port field
 Click Update

Step 3: Modify the Firewall Script

 Using the WUI, go to Maintenance > Firewall Script

 Un-comment / modify the example firewall marks section as shown in the following example.
Additional ports can be added as required by adding additional iptables entries and specifying the
appropriate port / protocol.

Chapter 6 – Configuring Load Balanced Services Page 107

 Appliance Administration Manual v8.1 Loadbalancer.org

 Click Update

*** The VIP is now configured and will be accessible on 192.168.111.240 , TCP ports 80 & 443 ***

Firewall Mark Notes:

 When using firewall marks the load balancer forwards traffic to the selected Real Server without
changing the destination port. So, incoming traffic to port 80 on the Virtual IP will be forwarded to port
80 on one of the Real Servers. Likewise, incoming traffic to port 443 will be forwarded to port 443 on
the same Real Server

 You can only have one health check port assigned, so if you are grouping port 80 and 443 traffic
together you can only check one of these ports, typically this would be port 80

 You can specify a range of ports rather than a single port as shown below:

iptables -t mangle -A PREROUTING -p tcp -d 10.141.12.34 --dport 1024:5000 -j MARK --set-mark 1

this specifies destination ports from 1024 to 5000

 You can leave the upper limit blank to use the default upper limit as shown below:

iptables -t mangle -A PREROUTING -p tcp -d 10.141.12.34 --dport 1024: -j MARK --set-mark 1

this specifies destination ports from 1024 to 65536

Chapter 6 – Configuring Load Balanced Services Page 108

 Appliance Administration Manual v8.1 Loadbalancer.org

 You can specify a range of IP addresses as shown below:

iptables -t mangle -A PREROUTING -p tcp -m iprange --dst-range 10.141.12.34-10.141.12.40 --dport 80

-j MARK --set-mark 1

this specifies the destination IP address as a range from 10.141.12.34 to 10.141.12.40

Layer 4 – Advanced Configuration

This section allows you to configure the various layer 4 global settings.

Lock Ldirectord Configuration – Prevent the web interface from writing the Ldirectord configuration file,
so that manual changes are retained. Manual changes to the Ldirectord configuration file may be
overwritten if settings are edited in the WUI. Locking the configuration file will prevent the web interface
from modifying the file so that custom edits are preserved.

A warning message will be displayed on all Layer 4 configuration pages, and changes will be denied.

NOTE : If manual changes are made to configuration files, then Lock Ldirectord
Configuration is unchecked, any changes made via the WUI will overwrite the manual
changes.

Chapter 6 – Configuring Load Balanced Services Page 109

 Appliance Administration Manual v8.1 Loadbalancer.org

Check Interval – Layer 4 (Ldirectord) health check interval in seconds. If this setting is too low, you may
experience unexpected Real Server downtime.

Check Timeout – Layer 4 (Ldirectord) health check timeout in seconds. If this setting is too low, you may
induce unexpected Real Server downtime.

Negotiate Timeout – Layer 4 (Ldirectord) negotiate health check timeout in seconds. The negotiate
checks may take longer to process as they involve more server side processing than a simple TCP socket
connect check. If this setting is too low, you may induce unexpected Real Server downtime.

Failure Count – Layer 4 (Ldirectord) number of times a check has to fail before taking server offline. The
time to detect a failure and take down a server will be (check interval + check timeout) * failure count.

Quiescent – When a Real Server fails a health check, do we kill all connections?
When Quiescent is set to yes, on a health check failure the Real Server is not removed from the load
balancing table, but the weight is set to 0. Persistent connections will continue to be routed to the failed
server, but no new connections will be accepted.
When Quiescent is set to no, the server is completely removed from the load balancing table on a health
check failure. Persistent connections will be broken and sent to a different Real Server.
N.B. Quiescent only applies to health checks – it has no effect on taking Real Servers offline in System
Overview. To manually force a Real Server to be removed from the table, set Quiescent to no and arrange
for the server to fail its health check. This may be done, for example, by shutting down the daemon or
service, changing the negotiate check value, or shutting down the server.

Email Alert Source Address – Specify the global source address of the email alerts. When an email alert is
sent, the system will use this address as the 'From' field.

Email Alert Destination Address – Specify the global destination email alert address. This address is used
to send notifications of Real Server health check failures. This can also be configured on a Virtual Service
level.

Auto NAT – Automatically NAT outbound network connections from internal servers. By default servers
behind the load balancer in a NAT configuration will not have access to the outside network. However
clients on the outside will be able to access load balanced services. By enabling Auto NAT the internal
servers will have their requests automatically mapped to the load balancers external IP address. The
default configuration is to map all requests originating from internal network eth0 to the external IP on
eth1. If you are using a different interface for external traffic you can select it here. Manual SNAT and DNAT
configurations for individual servers can also be configured in the firewall script.

Multi-threaded – Perform health checks with multiple threads. Using multiple-threads for health checks
will increase performance when you have a large number of Virtual Services.

Chapter 6 – Configuring Load Balanced Services Page 110

 Appliance Administration Manual v8.1 Loadbalancer.org

Layer 7 Services

The Basics
Layer 7 services are based on HAProxy which is a fast and reliable proxying and load balancing solution for
TCP and HTTP-based applications.
Since HAProxy is a full proxy, Layer 7 services are not transparent by default, i.e. the client source IP address
is lost as requests pass through the load balancer and instead are replaced by the load balancer's own IP
address.
Layer 7 supports a number of persistence methods including source IP address, HTTP cookie (both
application based and inserted), Connection Broker, RDP cookie and SSL session ID.
When a VIP is added the load balancer automatically adds a corresponding floating IP address which is
activated instantly. Check View Configuration > Network Configuration to ensure that the Floating IP
address has been activated correctly. They will show up as secondary IP addresses under the relevant
interface.
Multiple ports can be defined per VIP, for example 80 & 443. In this case it may also be useful to enable
persistence (aka affinity / stickiness) to ensure that clients hit the same back-end server for both HTTP &
HTTPS traffic and also prevent the client having to renegotiate the SSL connection.
With Layer 7, port re-direction is possible, i.e. VIP:80 → RIP:8080 is supported
Manual configuration of layer 7 services is possible using the WUI option: Cluster Configuration > Layer 7
– Manual Configuration

NOTE : It's not possible to configure a VIP on the same IP address as any of the network
interfaces. this ensures services can 'float' (move) between master and slave appliances

Creating Virtual Services (VIPs)

Each Virtual Service can have an unlimited number of Real Servers (except the Enterprise R20 which is
limited to 5 x VIPs each with up to 4 RIPs). Typically you'll need one Virtual Service for each distinct cluster.
Multiple ports can also be specified.

to add a new layer 7 VIP:

 In the WUI, open Cluster Configuration > Layer 7 – Virtual Services

 Click Add a new Virtual Service

Chapter 6 – Configuring Load Balanced Services Page 111

 Appliance Administration Manual v8.1 Loadbalancer.org

 Enter an appropriate Label (name) for the new Virtual Service

 Enter the required IP address in the Virtual Service IP Address field

 Enter the required ports(s) in the Virtual Service Ports field, separate multiple ports with commas,
specify a range with a hyphen and specify all ports using an asterisk

NOTE : the following ports are used by the appliance and therefore cannot be used for
Virtual Services: 22 (SSH), 9080 (WUI – HTTP), 9443 (WUI – HTTPS), 7777 (HAProxy statistics
page), 7778 (HAProxy persistence table replication and 9081 (nginx fallback page).

 Select the Layer 7 protocol to be handled by this Virtual Service, either HTTP or TCP

HTTP Mode – Selected if the Virtual Service will handle only HTTP traffic. Allows more flexibility in the
processing of connections. The HTTP Cookie and HTTP application cookie modes, and the X-
Forwarded-For header all require HTTP to be selected. In addition, HAProxy logs will show more
information on the client requests and Real Server responses.

TCP Mode – Required for non HTTP traffic such as HTTPS, RPC, RDP, FTP etc.

 If the VIP will be configured manually, check (enable) the Manual Configuration check-box
N.B. Please refer to page 119 for more information on manually configuring layer 7 services

 Click Update

 Now proceed to define the RIPs (Real Servers) as detailed on page 118

Modifying a Virtual Service

When first adding a Virtual Service, only certain values can be configured, others are set at their default
setting. These values can be changed after the Virtual Service has been created by clicking Modify next to
the relevant Virtual Service. Additional settings that can be changed are:

Option Description
HTTP Pipeline Mode Select how HAProxy should handle HTTP pipelining to client and server

No change - Act as a transparent tunnel, allowing the client and server to

negotiate pipelining.

Close both client and server - Disable pipelining, always closing

connections to both client and server using HTTP.

Keep-alive client, close server - Allow client to negotiate pipelining,

whilst closing the server connection using HTTP.

Close client, force close server - Close the server connection at the TCP
layer, as well as sending the Connection: close header. Also close the
client connection using HTTP.
Work around broken Work around Real Servers that do not correctly implement the HTTP
Connection: close Connection:close option. This does not take effect when HTTP pipeline
mode is set to No change.

Chapter 6 – Configuring Load Balanced Services Page 112

Appliance Administration Manual v8.1 Loadbalancer.org

Configure Content This allows ACL's to be configured. Please see the section below for more
Redirection details.
Balance Mode The scheduler used to specify server rotation. Specify the scheduler to
utilize when deciding the back-end server to use for the next new
connection.
Persistence Mode Select how the load balancer should track clients so as to direct each
request to the same server.

HTTP Cookie - The load balancer will set an HTTP Cookie to track each
client.
Application Cookie - Where an existing HTTP Cookie is set by the web
application on the Real Servers, use this to track each client.

SSL Session ID - Read the Session ID from the SSL connection and use
this to track each client.

MS Session Broker - Use the server-set msts RDP Cookie to track clients
connecting to a Microsoft Terminal Server. The Session Broker service
must be enabled on the real servers.

RDP Client Cookie - Use the client-set mstshash RDP Cookie to track
clients connecting to a Microsoft Terminal Server. If the cookie is missing,
source IP persistence will be used instead.

Source IP - Make sure the same source IP always hits the same server.

HTTP Cookie and Source IP - As HTTP Cookie, falling back to Source IP

if the cookie is missing from the HTTP request.

X-Forwarded-For and Source IP – Use X-Forwarded-For, falling back to

Source IP if the X-Forwarded-For header is missing form the request.
(NOTE: You cannot use the set X-Forwarded-For header option with this
method of persistence. It will be disabled.

None - No persistence. The allocation of clients to Real Servers will be

determined solely by the Balance Mode.
Persistence Options The persistence options depend on which mode is selected. The
following list details all available options.

HTTP Cookie name – set the name of the HTTP cookie

Application Cookie name - The name of a cookie used by the

application running on the Real Servers. If set, this enables connection
persistence based on an existing application cookie, ensuring that a client
is always directed to the same Real Server. Note that this option requires
the selection of HTTP Application Cookie persistence mode.

Application Cookie Length – The number of characters of the

application cookie value to match. When storing and matching an
Application Cookie value, the loadbalancer will use only the number of
characters given here. If the cookie value is shorter than this maximum,
only the actual length will be stored.

Application Cookie hold time - The time-out period before an idle

application cookie is removed from memory. The application cookie will
be removed from memory when it has been idle for longer than the Hold

Chapter 6 – Configuring Load Balanced Services Page 113

Appliance Administration Manual v8.1 Loadbalancer.org

Time period. The default units are milliseconds.

Persistence timeout - The time-out period before an idle connection is

removed from the connection table. The source IP address will be
removed from memory when it has been idle for longer than the
persistence timeout. The default units are minutes.

Persistence table size - The size of the table of connections in KB. The
size of the table of connections (approx 50 bytes per entry) where
connection information is stored to allow a session to return to the same
server within the timeout period. The default units are in KB.
Feedback Method Select whether HAProxy should query each Real Server for its load level.

Agent - The Real Server is queried every health check interval for the real
server's percent CPU idle. This is used to set each Real Server's weight to
a value proportional to its initial weight. For example, if the initial weight is
100 and the percentage cpu idle is 34, the weight will be set to 34.
Remember lower numbers mean lower priority for traffic, when
compared with other real servers in the pool.

None - HAProxy will not modify the Real Server's weight.

Fallback Server Configure fallback server settings. i.e. where to direct requests if all RIPs
are down.

IP Address – define the serves IP address

Port - define the serves IP address

Fallback Persistence - Configure the Fallback server to be persistent.

During a health-check failure users can be forwarded to a fallback server.
Setting this to on will make this server persistent so that when the Real
Servers are put back in the pool, they will remain on the fallback server
until their persistence times out. Setting this to off will move users to a
Real Server as soon as one is available.
Health Checks Specify the type of health check to be performed on the real servers.

Negotiate HTTP - Scan the page specified in Request to Send,

and check the returned data for the Response Expected string.

Negotiate HTTPS - Scan the page specified in Request to Send,

and check the returned data for the Response Expected string.

N.B. If a negotiate http or https check is used and Request to Send is

configured but Response Expected is left blank, the appliance looks for a
200 OK response from the real server.

Connect to port - Attempt to make a connection to the specified port.

External Script - Use a custom file for the health check. Specify the script
name & path in the Check Script field.

MySQL - The check consists of sending two MySQL packets, one Client
Authentication packet, and one QUIT packet, to correctly close the
MySQL session. It then parses the MySQL Handshake Initialization packet
and/or Error packet. It's a basic but useful test and does not produce
errors or aborted connects on the server. However, it requires adding an
authorization in the MySQL table as follows:

Chapter 6 – Configuring Load Balanced Services Page 114

Appliance Administration Manual v8.1 Loadbalancer.org

use mysql; INSERT INTO user (Host,User) values ('<appliance-

IP>','<username>'); flush privileges;

e.g.

use mysql; INSERT INTO user (Host,User) values ('192.168.1.1','probe'); flush

privileges;

No checks, Always on – No health checks, all real servers are marked

online.
Health Check Options The health check options depend on which mode is selected. The
following list details the possible options.

Check Port - Specify a different port for health checks. If specified this
setting overrides the default checkport, useful when you are balancing
multiple ports.

Request to send - Specify a specific file for the health check. Open the
specified file and check for the response expected. This may be used to
run a server-side script to check the health of the backend application.

For example, if index.html was specified in this field, the following check
directive would be automatically created in the HAProxy configuration
file:
option httpchk GET /index.html HTTP/1.0

N.B. the back-slash character before 'index.html' is added automatically

Response expected - The content expected for a valid health check on

the specified file. The response expected can be any valid regular
expression.
Continuing the example above, if the file index.html contained the word
'Copyright' response expected would be set to Copyright. The following
check directive would then be automatically created in the HAProxy
configuration file: http-check expect rstring Copyright

Check Script – Specify the external check script.

Username – Specify the SQL database username.

Host Header - Set the HTTP Host header to be sent with health check
requests. If the real server's web server is configured to require a Host
header, the value to be used in health checks may be set here.
Maximum Connections Specifies the maximal number of concurrent connections that will be sent
to this server. If the number of incoming concurrent requests goes higher
than this value, they will be queued, waiting for a connection to be
released.
Timeout Use this option to override the default client & server timeouts in the
Layer 7 advanced section.
Set X-Forwarded-For Header Instruct HAProxy to add an X-Forwarded-For (XFF) header to all requests,
showing the client's IP Address. If HTTP is selected under Layer 7 Protocol,
HAProxy is able to process the header of incoming requests. With this
option enabled, it will append a new X-Forwarded-For header containing
the client's IP Address. This information may be extracted by the Real
Server for use in web applications or logging.

Chapter 6 – Configuring Load Balanced Services Page 115

 Appliance Administration Manual v8.1 Loadbalancer.org

Force to HTTPS If set to 'Yes' any HTTP connections that are made on this VIP will be
forced to reconnect using HTTPS.
This will keep any entered URL. If you are terminating the SSL on the
Loadbalancer you should use the same VIP address for both the SSL
Termination and Layer7 configurations.
HTTPS Redirect Code Indicates which type of HTTP redirection is desired. Codes 301, 302, 303,
(available when Force to 307 and 308 are supported, with 302 used by default if no code is
HTTPS is enabled) specified.

301 means "Moved permanently", and a browser may cache the Location.
302 means "Moved permanently" and means that the browser should not
cache the redirection.
303 is equivalent to 302 except that the browser will fetch the location
with a GET method.
307 is just like 302 but makes it clear that the same method must be
reused.
308 replaces 301 if the same method must be used.
Proxy Protocol Enable Proxy Protocol if using STunnel SSL Off-load. If you wish to use
this VIP with STunnel for SSL off-load whilst passing the client's IP address
to the real servers this option needs to be enabled (checked). Please
ensure that TProxy is enabled in the Layer7 Advanced options and that the
'Set as Transparent Proxy' is enabled in your STunnel VIP.
Enable Compression Enable gzip HTTP compression. The following MIME types will be
compressed when this is enabled : text/html , text/plain , text/css ,
text/xml , text/javascript , application/javascript , application/xml

NOTE : For more details on configuring health-checks please refer to Chapter 8 starting on
page 164.

Configuring Content Redirection (ACLs)

The WUI now supports the ability to create ACL's which can be used to control and direct HTTP traffic
based on the rules defined.

• Multiple rules can be defined using the Add button

• Once all rules have been defined, click Save to save the rules, then click Update to update the VIP,
then click Reload HAProxy at the top of the page to apply the new settings
In the example above, requests are redirected to the URL location http://www.example.com if the path

Chapter 6 – Configuring Load Balanced Services Page 116

 Appliance Administration Manual v8.1 Loadbalancer.org

begins with /example

e.g. if the requested URL is : http://www.domain.com/example

the request is redirected to : http://www.example.com

Other Examples:

In the example above, requests are redirected to the URL prefix http://www.domain3.com if the host
header value is www.domain1.com

e.g. if the requested URL is : http://www.domain1.com/contract

the request is redirected to : http://www.domain3.com/contract

In the example above, requests are forwarded to the backend called Blog if the path begins with /blog

e.g. if the requested URL is : http://www.domain1.com/blog

the request is forwarded to the manually defined backend called Blog

Requests to http://www.domain1.com/<other locations> are forwarded to the Real Servers that were
defined using the WUI option : Cluster Configuration > Layer 7 – Real Servers

To define the backend, use the WUI option : Cluster Configuration > Layer 7 – Manual Configuration

The following example shows how the backend is defined:

backend Blog
mode http

Chapter 6 – Configuring Load Balanced Services Page 117

 Appliance Administration Manual v8.1 Loadbalancer.org

balance roundrobin
option forwardfor
server rip3 192.168.110.242:80 weight 1 check
server rip4 192.168.110.243:80 weight 1 check

NOTE : When defining ACL's that refer to backends, the backend must exist before HAProxy
can be successfully restarted.

NOTE : for more details on configuring ACL's please also refer to the HAProxy online
documentation available here

Creating Real Servers (RIPs)

You can add an unlimited number of Real Servers to each Virtual Service (except the Enterprise R20 which
is limited to 5 x VIPs each with up to 4 RIPs). For layer 7 VIPs port redirection is possible so the Real Server
port field can be set to a different value to the VIP port. Real Servers in a Layer 7 configuration can be on
any subnet in any network as long as they are accessible from the load balancer.

to add a new layer 7 RIP:

 In the WUI, open Cluster Configuration > Layer 7 – Real Servers

 Click Add a new Real Server next to the relevant Virtual Service

 Enter an appropriate Label (name) for the new Real Server

 Enter the required IP address in the Real Server IP Address field

 Specify the required Weight, this is an integer specifying the capacity of a server relative to the others in
the pool, the valid values of weight are 0 through to 65535, the default is 1

NOTE : The configuration options Re-Encrypt to Backend, Minimum Connections and

Maximum Connections are available when the Real Server is modified using Modify after the
RIP has been created.

Chapter 6 – Configuring Load Balanced Services Page 118

 Appliance Administration Manual v8.1 Loadbalancer.org

Persistence Considerations

Persistence State Table Replication

If you want the current persistent connection table to work when the master load balancer swaps over to
the slave then this can be enabled using the WUI. Enabling this option will replicate persistence tables for
all relevant layer 7 VIPs to the peer load balancer.

to enable persistence state table replication:

 In the WUI, open Cluster Configuration > Layer 7 – Advanced Configuration

 Enable the Persistence Table Replication

 Click Update

Layer 7 – Custom Configurations

Custom Layer 7 services can be configured via the WUI.

Configuring Manual Virtual Services

Step 1
Create a new layer 7 Virtual Service using the WUI option: Cluster Configuration > Layer 7 - Virtual Services
ensuring that the Manual Configuration check-box is ticked. Enabling this option stops the HAProxy
configuration file being written for this virtual service, leaving the user to configure via the WUI option:
Cluster Configuration > Layer 7 – Manual Configuration instead.

Step 2
Define the required layer 7 Real Servers using the WUI option: Cluster Configuration > Layer 7 – Real
Servers.

Step 3
Use the WUI option: Cluster Configuration > Layer 7 - Manual Configuration to manually define the Virtual
Service and Real Servers using the same Names, IP Addresses and Ports used in steps 1 & 2.

NOTE : Make sure you use the same Names, IP Addresses and Ports in Step 3 as you did in
Step 1 & 2. This is required to ensure that the system overview is able to report the VIP & RIP
status correctly. If different details were used, this would not be possible.

NOTE : It's now possible to define ACL rules at layer 7 using the WUI so depending on your
requirements a manual configuration may not be required. Please refer to page 116 for more
details on configuring ACL's.

Chapter 6 – Configuring Load Balanced Services Page 119

 Appliance Administration Manual v8.1 Loadbalancer.org

Manual Config Ex. 1 – Simple HTTP Redirect

In this example, requests that start with /staff/ or /staff will be redirected to https://login.domain.com
listen VIP1
bind 192.168.2.110:80
mode http
balance leastconn
acl ACL-1 path_beg /staff/ ← see note 1
acl ACL-2 path_beg /staff ← see note 1
redirect location https://login.domain.com if ACL-1 or ACL-2 ← see note 2
cookie SERVERID insert nocache indirect
server backup 127.0.0.1:9081 backup non-stick
option httpclose
option forwardfor
option redispatch
option abortonclose
maxconn 40000
server rip1 192.168.110.111:80 weight 1 cookie rip1 check inter 2000 rise 2 fall 3 minconn 0 maxconn 0 on-
marked-down shutdown-sessions
server rip1 192.168.110.112:80 weight 1 cookie rip1 check inter 2000 rise 2 fall 3 minconn 0 maxconn 0 on-
marked-down shutdown-sessions

Configuration Steps:

1. Using the WUI option: Cluster Configuration > Layer 7 – Virtual Services create a Layer 7 VIP with
the required Label (name), IP Address and Port, and ensure that the Manual Configuration check-
box is enabled, e.g. :

2. Using the WUI option: Cluster Configuration > Layer 7 – Real Servers define the associated RIPs in
the normal way, e.g. :

Chapter 6 – Configuring Load Balanced Services Page 120

 Appliance Administration Manual v8.1 Loadbalancer.org

3. Select the WUI option: Cluster Configuration > Layer 7 – Manual Configuration and define the
required VIP / RIP settings in the text window using the same Names, IP Addresses and Ports used
in the WUI. .e.g. :
listen VIP1
bind 192.168.2.110:80
mode http
balance leastconn
acl ACL-1 path_beg /staff/
acl ACL-2 path_beg /staff
redirect location https://login.domain.com if ACL-1 or ACL-2
cookie SERVERID insert nocache indirect
server backup 127.0.0.1:9081 backup non-stick
option httpclose
option forwardfor
option redispatch
option abortonclose
maxconn 40000
server rip1 192.168.110.111:80 weight 1 cookie rip1 check inter 2000 rise 2 fall 3 minconn 0
maxconn 0 on-marked-down shutdown-sessions
server rip1 192.168.110.112:80 weight 1 cookie rip1 check inter 2000 rise 2 fall 3 minconn 0
maxconn 0 on-marked-down shutdown-sessions

4. Click Update
5. Now reload HAProxy using the Reload HAProxy button in the blue Commit Changes box at the
top of the screen or by using the WUI option: Maintenance > Restart Services

Notes:
1. These lines configure 2 ACL's named ACL-1 & ACL-2 where the criteria for a match is that the URL
starts with either /staff/ or /staff
2. This line causes a redirect to https://login.domain.com to occur when either acl is matched

Manual Config Ex. 2 – Load Balancing with URL matching using ACL's
To support URL matched load balancing the structure of the HAProxy configuration file must be changed
to use the front-end / back-end model as shown in the example below:

frontend f1
bind 192.168.2.110:80
acl ACL-1 path_beg /test1
acl ACL-2 path_beg /test2
use_backend b1 if ACL-1
use_backend b2 if ACL-2
default_backend b2
option httpclose

backend b1
cookie SERVERID insert nocache indirect
server s1 192.168.2.111:80 weight 1 cookie s1 check
server s2 192.168.2.112:80 weight 1 cookie s2 check

backend b2
cookie SERVERID insert nocache indirect
server s3 192.168.2.113:80 weight 1 cookie s3 check
server s4 192.168.2.114:80 weight 1 cookie s4 check
Configuration Steps:

Chapter 6 – Configuring Load Balanced Services Page 121

 Appliance Administration Manual v8.1 Loadbalancer.org

1. Using the WUI option: Cluster Configuration > Floating IPs , add a floating IP for the new VIP, in this
example 192.168.2.110 is added to match the IP address required:

2. Click Add Floating IP

3. Select the WUI option: Cluster Configuration > Layer 7 – Manual Configuration and define the
required VIP / RIP settings in the text window. .e.g. :
frontend F1
bind 192.168.2.110:80
acl ACL-1 path_beg /test1
acl ACL-2 path_beg /test2
use_backend B1 if ACL-1
use_backend B2 if ACL-2
default_backend B2
option httpclose

backend B1
cookie SERVERID insert nocache indirect
server s1 192.168.2.111:80 weight 1 cookie s1 check
server s2 192.168.2.112:80 weight 1 cookie s2 check

backend B2
cookie SERVERID insert nocache indirect
server s3 192.168.2.113:80 weight 1 cookie s3 check
server s3 192.168.2.114:80 weight 1 cookie s3 check

4. Click Update

5. Now reload HAProxy using the Reload HAProxy button in the blue Commit Changes box at the
top of the screen or by using the WUI option: Maintenance > Restart Services

Notes:

1. ACL-1 & ACL-2 are the names of the ACLs

2. path_beg matches the beginning of the path to a certain value, in this case /test1 & /test2 and
then directs requests to the appropriate back-end, either backend B1 or B2

IMPORTANT : This example uses the Frontend/Backend structure to define the Layer 7
Virtual Service. When using this structure, the related Virtual Service cannot be displayed in
the System Overview so there is no need to define a matching VIP in this case.

Chapter 6 – Configuring Load Balanced Services Page 122

 Appliance Administration Manual v8.1 Loadbalancer.org

These are fairly simple examples to show the principle of using ACLs. For much more information please
refer to the HAProxy manual at the following link:

http://www.haproxy.org/download/1.6/doc/configuration.txt

(Search that page for ''Using ACLs”)

NOTE : Don't hesitate to contact [email protected] to discuss any specific ACL or

other custom configuration requirements you may have.

HAProxy Error Codes

For reference, HAProxy's own error codes are as follows:

Code When / Reason

200 access to stats, and when replying to monitoring requests

301 when performing a redirection, depending on the configured code

302 when performing a redirection, depending on the configured code

303 when performing a redirection, depending on the configured code

400 for an invalid or too large request

401 when an authentication is required to perform the action (when accessing the stats page)

403 when a request is forbidden by a "block" ACL or "reqdeny" filter

408 when the request timeout strikes before the request is complete

500 when HAProxy encounters an unrecoverable internal error, such as a memory allocation
failure, which should never happen

502 when the server returns an empty, invalid or incomplete response, or when an "rspdeny"
filter blocks the response

503 when no server was available to handle the request, or in response to monitoring requests
which match the "monitor fail" condition

504 when the response timeout strikes before the server responds

For a complete HAProxy reference please refer to the following link:

http://www.haproxy.org/download/1.6/doc/configuration.txt

Chapter 6 – Configuring Load Balanced Services Page 123

 Appliance Administration Manual v8.1 Loadbalancer.org

Layer 7 – Advanced Configuration

This section allows you to configure the various layer 7 global settings.

Chapter 6 – Configuring Load Balanced Services Page 124

 Appliance Administration Manual v8.1 Loadbalancer.org

Lock HAProxy Configuration – Prevent the WUI writing to the HAProxy configuration file. Manual
changes to the HAProxy configuration file may be overwritten if settings are edited in the web interface.
Locking the configuration file will prevent the web interface from modifying the file, so that custom edits
are preserved. A warning message will be displayed on all Layer 7 configuration pages, and changes will be
denied.

NOTE : This Feature is now deprecated. It's now possible to configure each virtual service as
read-only. The manual configuration can then be created using the WUI option: Layer 7 -
Manual Configuration

Logging – Activate detailed logging of the Layer 7 HAProxy service. When activated the HAProxy log is
written to /var/log/haproxy.log.

Log Only Errors – Do not log operational connection details, only log errors.

Redispatch – Allows HAProxy to break persistence and redistribute to working servers should failure
occur. Normally this setting should not require changing.

Connection Timeout – HAProxy connection timeout in milliseconds. This setting should normally not
require changing.

Client Timeout – HAProxy client timeout in milliseconds. This setting should normally not require
changing.

Real Server Timeout – HAProxy Real Server timeout in milliseconds. This setting should not require
changing.

Maximum Connections – HAProxy maximum concurrent connections. This setting should not require
changing, unless you are running a high volume site. See also Maximum Connections for a Virtual Service
(HAProxy).

Ulimit – The maximum number of file descriptors used for layer 7 load balancing.

This value is auto-configured internally based on other system parameters and does not need to be set
here.

Abort on Close – Abort connections when users close their connection. Recommended as the probability
for a closed input channel to represent a user hitting the 'STOP' button is close to 100%

Transparent Proxy – Enable TProxy support for Layer 7 HAProxy. TProxy support is required in order for
the Real Servers behind a layer 7 HAProxy configuration to see the client source IP address. The load
balancer must be in a NAT configuration (internal and external subnets) with the Real Servers using an IP
address on the load balancer (preferably a floating IP) as their default gateway.

N.B. all Layer 4 methods are transparent by default

NOTE : For more details on using TProxy, refer to page 143.

N.B. Since the load balancer must be in a NAT configuration (i.e. VIPs & RIPs in different subnets and
default gateway on the real servers set as an IP on the load balancer) to utilize TProxy, it's not always an
appropriate solution. In situations such as this, it's also possible to use the X-forwarded-for header with

Chapter 6 – Configuring Load Balanced Services Page 125

 Appliance Administration Manual v8.1 Loadbalancer.org

layer 7 Virtual Services. Most web servers can then be configured to record the X-Forwarded-For IP
address in the log files.

For details on how to enable X-Forwarded-For support, please refer to page 115. For details on how to
enable X-Forwarded-For support with Apache and IIS, please refer to the following Loadbalancer.org blog
links:

Apache - http://www.loadbalancer.org/blog/apache-and-x-forwarded-for-headers
IIS - http://www.loadbalancer.org/blog/iis-and-x-forwarded-for-header

Interval – Interval between health checks. This is the time interval between Real Server health checks in
milliseconds.

Rise – Number of health checks to Rise. The number of positive health checks required before re-
activating a Real Server.

Fall – Number of health checks to Fall. The number of negative health checks required before de-
activating a Real Server.

Feedback Agent Interval - The time in milliseconds between each feedback agent check from HAProxy to
the feedback agent.

HAProxy Statistics Page Password – Set the password used to access Reports > Layer 7 Status.

HAProxy Statistics Page Port – Change the listening port for the HAProxy web based statistics report
from the default of TCP 7777.

Advanced Stats - Enable/disable additional actions available on the HAProxy stats page.

Request Buffer Length – Set the health check buffer length in bytes.

N.B. Changing this value will effect the performance of HAProxy. Do not make changes unless you know
exactly what you are doing.

Lower values allow more sessions to coexist in the same amount of RAM, and higher values allow some
applications with very large cookies to work. The default value is 16384 bytes. It is strongly recommended
not to change this from the default value, as very low values will break some services such as statistics, and
values larger than the default size will increase memory usage, possibly causing the system to run out of
memory. Administrators should consider reducing the Maximum Connections parameter if the request
buffer is increased.

Header Buffer Length – Set the header buffer length, in bytes The header buffer is a section of the request
buffer, reserved for the addition and rewriting of request headers. The default value is 1024 bytes. Most
applications will only require a small header buffer, as few headers are added or rewritten.

Persistence Table Replication – When enabled, HAProxy's persistence tables are replicated to the slave
device.

Persistence Table Replication Port – Set the TCP port to use for persistence table replication. The default
port is TCP 7778.

eMail Alert From – Set the 'from address' for email alerts

eMail Alert To – Set the 'to address' for email alerts

eMail Server Address – Set the email server address as either an IP address or FQDN

eMail Server Port – Set the email server TCP port

Chapter 6 – Configuring Load Balanced Services Page 126

 Appliance Administration Manual v8.1 Loadbalancer.org

SSL Termination

Concepts
SSL termination can be performed on the Real Servers (aka SSL pass-through ) or on the load balancer (aka
SSL offloading ).

SSL Termination on the Real Servers:

Notes:

• Data is encrypted from client to server. This provides full end-to-end data encryption as shown in
the diagram below

• It's not possible to use HTTP cookie persistence since the packet is encrypted and therefore the
cookie cannot be read – in this case the only option is source IP persistence

SSL Termination on the Load balancer:

Notes:

• Since SSL is terminated on the load balancer, by default, data from the load balancer to the web
servers is not encrypted as shown in the diagram above. This may or may not be an issue
depending on the network structure between the load balancer and web servers and your security
requirements

N.B. Re-encryption is possible between the load balancer and the Real Servers (aka SSL bridging).
To use this, enable the 'Re-encrypt to Backend' option for each RIP and click Update. Each server
must be correctly configured for HTTPS for this to work and an appropriate certificate must also
be installed. See page 138 for more details.

Chapter 6 – Configuring Load Balanced Services Page 127

 Appliance Administration Manual v8.1 Loadbalancer.org

• It's possible to use HTTP cookie based persistence

• A Pound or STunnel SSL VIP is used to terminate SSL. The backend for the VIP can be either a Layer
4 NAT mode VIP or a Layer 7 HAProxy VIP. Layer 4 DR mode cannot be used since Pound acts as a
proxy, and the real servers see requests with a source IP address of the VIP. However, since the real
servers believe that they own the VIP (due to the loopback adapter configured to handle to ARP
problem) they are unable to reply to Pound.

NOTE : SSL termination on the load balancer can be very CPU intensive. In most cases, for a
scalable solution, terminating SSL on the Real Servers is the best option.

SSL Termination on the Real Servers (Recommended)

In this case SSL certificates are installed on each Real Server in the normal way. The load balancer is then
configured with a VIP that listens on HTTPS port 443 and distributes inbound requests to the Real Servers
again on port 443 as shown in the layer 4 DR mode example below:

A fairly common configuration is to include port 80 in the VIPs definition and also enable persistence. This
ensures that both HTTP and HTTPS requests from a particular client are always sent to the same Real
Server as shown below:

SSL Termination on the Load Balancer

In this case an SSL certificate must be installed on the load balancer. The appliance supports the use of
both STunnel (default) and Pound for SSL termination.
To configure SSL termination on the appliance an SSL Virtual Service must be defined that specifies an IP
address and port to listen for inbound HTTPS connections and a back-end IP address / port where to
forward the corresponding un-encrypted HTTP connection.
By default a self-signed certificate is used for the new VIP which is ideal for testing but needs to be
replaced for production deployments.

Chapter 6 – Configuring Load Balanced Services Page 128

 Appliance Administration Manual v8.1 Loadbalancer.org

Creating an STunnel SSL Virtual Service (the Default SSL Terminator)

to add an STunnel SSL VIP:

 In the WUI, open Cluster Configuration > SSL Termination

 Click Add a new Virtual Service

 Enter an appropriate Label (name) for the new Virtual Service

 Enter the required IP address in the Virtual Service IP address field

 Enter the required port in the Virtual Service Port field – typically 443

 Enter the required IP address in the Back-end Virtual Service IP Address field
This is normally the same IP address as the Virtual Service IP address but can be any valid IP. The IP
address specified must correspond to a Layer 7 HAProxy VIP or a Layer 4 NAT mode VIP. Unencrypted
traffic will be sent here for load balancing.
N.B. DR mode cannot be used since STunnel acts as a proxy, and the Real Servers see requests with a
source IP address of the Virtual Service. However since the Real Servers believe that they own the
Virtual IP (due to the Loopback Adapter configured to handle to ARP problem) they are unable to reply
to STunnel

Chapter 6 – Configuring Load Balanced Services Page 129

 Appliance Administration Manual v8.1 Loadbalancer.org

 Enter the required port in the Back-end Virtual Service Port field

 Define the list of accepted ciphers using the Ciphers to use field
By default the cipher is set to: ECDHE-RSA-AES128-GCM-SHA256:ECDHE-RSA-RC4-SHA:ECDHE-RSA-
AES128-SHA:RC4:HIGH:!MD5:!aNULL:!EDH
This can be modified as required, or the field can be cleared (blank) to allow all available ciphers (not
recommended)

 Configure Do not Insert Empty Fragments

Disables a countermeasure against a SSL 3.0/TLS 1.0 protocol vulnerability affecting CBC ciphers. This
option needs to be enabled (checked) to ensure mitigation of both the BEAST and CRIME MITM attacks.
It is also required for PCI Testing.

 Ensure SSL Terminator is set to STunnel

 Configure Delay DNS Lookup

Delay DNS lookup for 'connect' option. This option is useful for dynamic DNS, or when DNS is not
available during STunnel startup (road warrior VPN, dial-up configurations).

 Configure Disable SSLv2 Ciphers

When ticked this option disables all SSLv2 Ciphers by using the OpenSSL 'SSL_OP_NO_SSLv2' option.

 Configure Disable SSLv3 Ciphers

When ticked this option disables all SSLv3 Ciphers by using the OpenSSL 'SSL_OP_NO_SSLv3' option.
Please note that entering '!SSLv3' into a Cipher list can have an adverse effect and we recommend using
this option and not entering '!SSLv3'.

 Configure Allow Client Renegotiation

Sets whether the client is allowed to renegotiate the cipher order. This option should be enabled
(checked) to mitigate the BEAST attack.

 Configure Disable SSL Renegotiation

Applications of the SSL renegotiation include some authentication scenarios, or re-keying long lasting
connections. On the other hand this feature can facilitate a trivial CPU-exhaustion DoS attack. This
option should be enabled (checked) to mitigate the BEAST Attack.

 Configure Time to Close

Configure the global client response timeout in seconds. This setting should not require changing.

 Configure Set as Transparent Proxy

If you wish to use HAProxy and TProxy this option needs to be enabled (checked) to allow SSL
termination on the load balancer whilst passing the client's IP address to the Real Servers. This option
only enables TProxy on a Single STunnel VIP – if you're using HAProxy with this VIP you will also need
to enable TProxy for your HAProxy VIP (please refer to the examples on page 143)

 Click Update to create the SSL VIP

STunnel Cipher Settings and the BEAST Attack

The following STunnel options should be set to mitigate the BEAST attack:

Chapter 6 – Configuring Load Balanced Services Page 130

 Appliance Administration Manual v8.1 Loadbalancer.org

Ciphers to use – a minimum cipher list of 'RC4:HIGH:!MD5:!aNULL' is required

Allow Client Renegotiation – this option should be disabled (un-checked)

Do Not Insert Empty Fragments – this option should be enabled (checked)

Disable SSL Renegotiation – this option should be enabled (checked)

If these options are set, this should prevent the BEAST attack, and should also help to mitigate DoS attacks
and MITM Attacks.

Creating a Pound SSL Virtual Service

to add a Pound SSL VIP:

 In the WUI, open Cluster Configuration > SSL Termination

 Click Add a new Virtual Service

 Enter an appropriate Label (name) for the new Virtual Service

Chapter 6 – Configuring Load Balanced Services Page 131

Appliance Administration Manual v8.1 Loadbalancer.org

 Enter the required IP address in the Virtual Service IP address field

 Enter the required port in the Virtual Service Port field – typically 443

 Enter the required IP address in the Back-end Virtual Service IP address field
This is normally the same IP address as the Virtual Service IP address but can be any valid IP. The IP
address specified must correspond to a Layer 7 HAProxy VIP or a Layer 4 NAT mode VIP. Unencrypted
traffic will be sent here for load balancing.
N.B. DR mode cannot be used since Pound acts as a proxy, and the Real Servers see requests with a
source IP address of the Virtual Service. However since the Real Servers believe that they own the
Virtual IP (due to the Loopback Adapter configured to handle to ARP problem) they are unable to reply
to Pound

 Enter the required port in the Back-end Virtual Service Port field

 Define the list of accepted ciphers using the Ciphers to use field
By default the cipher is set to: ECDHE-RSA-AES128-GCM-SHA256:ECDHE-RSA-RC4-SHA:ECDHE-RSA-
AES128-SHA:RC4:HIGH:!MD5:!aNULL:!EDH
This can be modified as required, or the field can be cleared (blank) to allow all available ciphers (not
recommended)

 Configure Do Not Insert Empty Fragments

Disables a countermeasure against a SSL 3.0/TLS 1.0 protocol vulnerability affecting CBC ciphers. This
option needs to be enabled (checked) to ensure mitigation of both the BEAST and CRIME MITM attacks.
It is also required for PCI Testing.

 Ensure SSL Terminator is set to Pound

 Configure Enable WebDAV Verbs

When enabled extends which HTTP / WebDAV verbs are accepted.

 Configure Rewrite HTTP Redirects

Pound to change the Location: and Content-location: headers in responses If they point to the back-
end itself or to the listener (but with the wrong protocol) the response will be changed to show the
virtual host in the request. NOTE: If you do not know what this means leave this as the default (enabled).

 Configure Honor Cipher Order

When choosing a cipher during a handshake, normally the client's preference is used. If this directive is
enabled, the server's preference will be used instead. When choosing a cipher during a SSLv3 or TLSv1
handshake, normally the client's preference is used. If this directive is enabled, the server's preference
will be used instead.
This option should be enabled to mitigate the BEAST attack.

 Configure Allow Client Renegotiation

Sets whether the client is allowed to renegotiate the cipher order. In Pound when set to either:
- No Client Renegotiation, no client renegotiation will be honored
- Secure Renegotiation, secure renegotiation will be honored
- Insecure Renegotiation, insecure renegotiation will be honored

This option should be set to 'No Client Renegotiation' to mitigate the BEAST attack.

 Configure Disable SSLv2 Ciphers

Chapter 6 – Configuring Load Balanced Services Page 132

 Appliance Administration Manual v8.1 Loadbalancer.org

Allow the option to Disable all SSLv2 Ciphers. When ticked this option disables all SSLv2 Ciphers by
using the OpenSSL 'SSL_OP_NO_SSLv2' option.

 Configure Disable SSLv3 Ciphers

When ticked this option disables all SSLv3 Ciphers by using the OpenSSL 'SSL_OP_NO_SSLv3' option.
Please note that entering '!SSLv3' into a Cipher list can have an adverse effect and we recommend using
this option and not entering '!SSLv3'.

 Configure Disable SSL Compression

Disable DEFLATE compression even if both server and client supports it. If this option is enabled
(checked), the server will disable DEFLATE compression even if both server and client supports it. In
case compression is enabled an attacker with access to encrypted network traffic can conduct a
"CRIME" attack by making client issue requests with specific character sequences and observing
whether they got compressed or not, indicating their presence in part of the request that is not under
his control (e.g. cookie headers).

 Click Update to create the SSL VIP

Modifying a Pound SSL Virtual Service

When first adding a Pound SSL Virtual Service, only certain values can be configured, others are set at their
default setting. These values can be changed after the Virtual Service has been created by clicking Modify
next to the relevant Virtual Service. Additional settings that can be changed are:

Option Sub-Option Description

Headers Header Field Name Add your own header to be passed on by Pound. Set
Field Name allows the name part of the header to be
specified: [field-name]: [field-value]

Header Field Value Add your own header to be passed on by Pound. Set
Field Value allows the value part of the header to be
specified: [field-name]: [field-value]

Pound Cipher Settings and the BEAST Attack

The following Pound options should be set to mitigate the BEAST attack:

Ciphers to use – a minimum cipher list of 'RC4:HIGH:!MD5:!aNULL' is required

Honor Cipher Order – this option should be enabled (checked)

Allow Client Renegotiation – this option should be set to 'No Client Renegotiation'

Do not Insert Empty Fragments – this option should be enabled (checked)

If these options are set, this should prevent the BEAST attack, and should also help to mitigate DoS attacks
and MITM Attacks.

Chapter 6 – Configuring Load Balanced Services Page 133

 Appliance Administration Manual v8.1 Loadbalancer.org

Generating a CSR on the Load Balancer

By default, when creating an SSL Virtual Service a self-signed certificate is used. This is ideal for testing but
needs to be replaced for production deployments.
In order to obtain a valid signed certificate from a certificate authority such as Verisign or Thawte you'll
need to generate a certificate request (CSR).

to generate a CSR

 In the WUI, open Cluster Configuration > SSL Termination

 Click [Certificate] next to the relevant Virtual Service

 Compete the fields as shown in the example below:

 Click Generate SSL Certificate Request

Chapter 6 – Configuring Load Balanced Services Page 134

 Appliance Administration Manual v8.1 Loadbalancer.org

 Copy the resulting CSR from the top pane and send this to your chosen Certificate Authority

N.B. Select Apache as the platform type during the certificate generation process.

 Once you receive your signed certificate from the CA, copy/paste this into the lower pane

 If you need to add an intermediate certificate, paste it after the signed certificate in the lower pane.

 Click Upload signed certificate

Chapter 6 – Configuring Load Balanced Services Page 135

 Appliance Administration Manual v8.1 Loadbalancer.org

Using an Existing Certificate

It's possible to upload both PEM and PFX format certificates. PEM files should contain the private key
(without a password), the signed certificate issued by a Certificate Authority (CA) and also any additional
validation / intermediate certificates that may be required by the CA.

Creating a PEM file

 Using a text editor such as vi or vim under Linux or Notepad under Windows create an empty file called
pem.txt for example. Then copy/paste the Certificate, the Private Key and any additional Intermediate
Certificates into the file as follows (truncated versions are shown):

-----BEGIN CERTIFICATE-----

MIICsDCCAhmgAwIBAgIJAL98jhEiUm3iMA0GCSqGSIb3DQEBBQUAMEUxCzAJBgN

2bShC2AVC+ZDMNu6bvCdvfySi6EypUcIvEwao7ZbyaAEbcSVympQJdgs6W6ajiLSf£

-----END CERTIFICATE-----

-----BEGIN RSA PRIVATE KEY-----

MIICXAIBAAKBgQCcPYkYHm8gYwIm3HyoVxjrymusOeIFgZlWyuaebIrreCpIo+iydRf

YwC2ZCE0HwquomN/q4ctnhgeN+kugDxlgCTVYd3eo/Dv/KZ16p4HUlrTqwES4Lunff

-----END RSA PRIVATE KEY-----

-----BEGIN CERTIFICATE-----

MIICsDCCAhmgAwIBAgIJAL98jhEiUm3iMA0GCSqGSIb3DQEBBQUAMEUxCzAJBgN

E89UJCG2nMW5JVBNkyHYbQTvU8MeR3iIhe2fw+qVE2pgxWYWaGm8QwTsxQKgbx

2bShC2AVC+ZDMNu6bvCdvfySi6EypUcIvEwao7ZbyaAEbcSVympQJdgs6W6ajiLSf£

-----END CERTIFICATE-----

 Save the file

Exporting PFX Certificates from Windows Servers

When exporting certificates from Windows servers, make sure that Yes, export the private key is selected,
this will enable the output format to be PFX. Also make sure that Include all certificates in the
certification path if possible is selected.

Uploading PEM & PFX Certificates

 Using the WUI open Cluster Configuration > SSL Termination

 Click [Certificate] next to the relevant Virtual Service

 Navigate to the bottom of the screen, the using the browse option select the relevant certificate file
(either PEM or PFX format)

 Click Open to upload the certificate

 Once uploaded, restart Pound / STunnel using the restart link at the top of the page or via the WUI
option: Maintenance > Restart Services

Chapter 6 – Configuring Load Balanced Services Page 136

 Appliance Administration Manual v8.1 Loadbalancer.org

NOTE : If your master & slave are correctly configured as a clustered pair, when you upload
the certificate file to the master, the file will be automatically copied over to the slave unit.

NOTE : It's important to backup all of these files. This can be done via the WUI from
Maintenance > Backup & Restore > Download SSL Certificates.

Converting between certificate formats

In some circumstances it may be required to manually convert certificates between formats. In these cases
OpenSSL can be used. This is usually included by default in Linux distributions. For Windows, it can be
freely downloaded from the following location:
http://slproweb.com/products/Win32OpenSSL.html
At this URL you'll need to download and install the Visual C++ 2008 Redistributable, then download either
the light or full version of OpenSSL. Once installed, you'll have an OpenSSL directory located on your
filesystem (default location c:\OpenSSL)

To use the program, open a command window, navigate to the location where it was installed (by default
c:\OpenSSL\bin) then run the required command as detailed below.

Converting PFX certificates to PEM format

Using OpenSSL under Windows:

openssl pkcs12 -in drive:\path\filename.pfx -nodes -out drive:\path\filename.pem

e.g.

openssl pkcs12 -in c:\cert.pfx -nodes -out c:\cert.pem

Using the Appliance / Linux:

openssl pkcs12 -in /path/filename.pfx -nodes -out /path/filename.pem

e.g

openssl pkcs12 -in /root/cert.pfx -nodes -out /root/cert.pem

Converting .cer certificates to PEM format

Using OpenSSL under Windows:

openssl x509 -in filename.cer -inform DER -out filename.pem -outform PEM

e.g

openssl x509 -in c:\cert.cer -inform DER -out c:\cert.pem -outform PEM

Chapter 6 – Configuring Load Balanced Services Page 137

 Appliance Administration Manual v8.1 Loadbalancer.org

Using the Appliance / Linux:

openssl x509 -in filename.cer -inform DER -out filename.pem -outform PEM

e.g

openssl x509 -in cert.cer -inform DER -out cert.pem -outform PEM

Converting an Encrypted Private Key to an Unencrypted Key

If a password has been included in the private key, this should be removed before it is used with your PEM
file. This can be done using the following OpenSSL command either on the load balancer or another
machine with openssl installed:

openssl rsa -in encrypted-server.key -out unencrypted-server.key

SSL Re-encryption (aka SSL Bridging)

It's possible to terminate SSL on the load balancer and then re-encrypt the HTTP traffic between the load
balancer and each Real Server. Each Real Server must have an SSL certificate and be correctly configured
for HTTPS. This option DOES NOT check the state of the installed SSL Certificate on the Real Server which
will allow for the use of locally generated SSL Certificates.

To enable re-encryption:

 For each Real Server use the WUI option: Cluster Configuration > Layer 7 – Real Servers > Modify

 Enable the option Re-Encrypt to Backend

 Click Update

 Repeat for your other Real Server(s)

Chapter 6 – Configuring Load Balanced Services Page 138

 Appliance Administration Manual v8.1 Loadbalancer.org

SSL – Advanced Configuration

Pound Global Settings

Lock Pound Configuration – When enabled it will stop the user interface overwriting the configuration
files so manual changes can be made.

Logging – Activate detailed logging of the Pound SSL termination service. When activated the Pound log
is written to /var/log/Poundssl.

Client Timeout – Configure the global client response timeout in seconds. This setting should not require
changing.

Global Server Timeout – Configure the global Real Server response timeout in seconds. This setting
should not require changing.

Ulimit – Set Ulimit value for Pound the process. This setting will change the maximum number of file
descriptors available to the Pound process. The default is 81000.

Ulimit – Set Ulimit value for Pound the process. This setting will change the maximum number of file
descriptors available to the Pound process. The default is 81000.

Transparent Proxy – Enable TProxy support in Pound SSL. The combination of Pound, TProxy, and
HAProxy allows SSL termination on the load balancer whilst passing the client's IP address to the Real
Servers. This option also automatically enables TProxy for HAProxy.

NOTE : One consequence of using transparent proxy with both Pound and HAProxy is that
you can no longer access the HAProxy Virtual Service directly. With transparency turned on
HAProxy will only accept traffic from Pound. One way to get around this is to configure the
HAProxy VIP to listen on 2 ports. One will listen on port 80, and be your standard HTTP
service. The other will listen on a different port, 81 for example – and will be the destination
for traffic from Pound. This is covered on page 144.

Chapter 6 – Configuring Load Balanced Services Page 139

 Appliance Administration Manual v8.1 Loadbalancer.org

STunnel Global Settings

Debug Level – Option to set the debugging level for all STunnel Services. The Debug Level is a one of the
syslog level names or numbers emergency (0), Alert (1), Critical (2), err (3), Warning (4), Notice (5),
Information (6), or Debug (7). The higher the number the more detail will be contained in the STunnel Logs.

Disable Nagle Algorithm – With this option ticked (enabled) the Nagle Algorithm will be disabled. More
details can be found in RFC 896.

Chapter 6 – Configuring Load Balanced Services Page 140

 Appliance Administration Manual v8.1 Loadbalancer.org

HTTP to HTTPS Redirection

V7.6 introduced the capability to force HTTP to HTTPS redirection via the WUI. Previously, a manual edit
was required. This can be achieved both when terminating SSL on the Real Servers and when offloading
SSL on the load balancer.

SSL Termination on the Real Servers (Recommended)

This method requires 2 VIPs:

• VIP1 – This is a layer 7 (HAProxy), HTTP mode VIP that listens on port 80 and redirects all
connections to VIP2
N.B. This VIP will show purple/green in the System Overview. This occurs once Force to HTTPS is
enabled (see below)

• VIP2 – This is a layer 7 (HAProxy), TCP mode VIP that listens on port 443 and load balances
connections between real servers RIP1 & RIP2

VIP1 Redirect Configuration

Enable the Force to HTTPS options as shown below and set the redirect code as required:

NOTE : It's not possible to enable TProxy when using this configuration.

Chapter 6 – Configuring Load Balanced Services Page 141

 Appliance Administration Manual v8.1 Loadbalancer.org

SSL Termination on the Load Balancer

This method requires 2 VIPs:

• VIP1 – This is a Pound or STunnel VIP that listens on port 443, terminates the SSL connection and
then forwards the decrypted HTTP connections to VIP2 on port 80

• VIP2 – This is a layer 7 (HAProxy), HTTP mode VIP that listens on port 80 and load balances
connections between real servers RIP1 and RIP2. It also redirects connections that have NOT come
from Pound or STunnel, i.e. client connections directly on port 80

VIP2 Redirect Configuration

Enable the Force to HTTPS options as shown below and set the redirect code as required:

NOTE : It's not possible to enable TProxy when using this configuration.

NOTE : If you require to re-encrypt the data from the load balancer to the Real Server,
enable the Re-encrypt to Backend option for the each real server. See page 138 for more
details.

Chapter 6 – Configuring Load Balanced Services Page 142

 Appliance Administration Manual v8.1 Loadbalancer.org

Using Transparent Proxy (TProxy)

HAProxy, Pound and STunnel are proxies which means that a new connection is established from the proxy
out to the back-end server in response to an inbound client connection to the proxy. This means that the
source IP address of the packet reaching the server will be the proxies address, or more specifically the IP
address assigned to the load balancers Ethernet interface.
TProxy can be used with HAProxy, Pound and STunnel to maintain the actual source IP address of the
client. When enabling TProxy, it's important to be aware of the topology requirements for TProxy to work
correctly. This is covered in the examples below.

TProxy & HAProxy

In this example, TProxy is enabled with a layer 7 Virtual Service. This setup is illustrated in the following
diagram.

Topology Requirements / Notes

• The RIPs must be on a different subnet to the VIP – this can achieved by using 2 IP addresses
assigned to a single interface, or two separate interfaces (in the above example, eth1 = 192.168.2.1
and eth0 = 192.168.4.1)

• TProxy must be enabled using the WUI option: Cluster Configuration > Layer 7 – Advanced
Configuration and setting Transparent Proxy to 'On'

• On the Real Servers, the default gateway must be configured to be an IP address on the load
balancer. When using a clustered pair, this should be a floating IP to allow failover to the slave

Chapter 6 – Configuring Load Balanced Services Page 143

 Appliance Administration Manual v8.1 Loadbalancer.org

TProxy, HAProxy & Pound

In this example, Pound is used to terminate SSL. Pound passes the decrypted traffic to a layer 7 back-end
VIP where the Real Servers are configured. This setup is illustrated in the following diagram.

N.B. Using STunnel rather than Pound in this scenario is not supported. For STunnel, 2 separate HAProxy
VIPs must be used as described on the following page.

Topology Requirements / Notes

• The RIPs must be on a different subnet to the VIP – this can achieved by using 2 IP addresses
assigned to a single interface, or two separate interfaces (in the above example, eth1 = 192.168.2.1
and eth0 = 192.168.4.1)

• Configure the Layer 7 VIP to listen on 2 ports – e.g. 80 & 81, then use port 81 for the Pound back-
end and port 80 for client connections. Configure the Pound VIP to listen on the same IP address /
port 443 and set its back-end to be port 81 of the HAProxy VIP.
This way, clients connect to a single IP address listening on port 80 & 443.

• TProxy for HAProxy must be enabled using the WUI option: Cluster Configuration > Layer 7 –
Advanced Configuration and setting Transparent Proxy to 'On'

• TProxy for Pound must be enabled using the WUI option: Cluster Configuration > SSL – Advanced
Configuration and setting Transparent Proxy to 'On'

• On the Real Servers, the default gateway must be configured to be an IP address on the load
balancer. When using a clustered pair, this should be a floating IP to allow failover to the slave

Chapter 6 – Configuring Load Balanced Services Page 144

 Appliance Administration Manual v8.1 Loadbalancer.org

TProxy, HAProxy & STunnel

In this example, STunnel is used to terminate SSL. STunnel passes the decrypted traffic to a layer 7 back-
end VIP where the Real Servers are configured. As mentioned in the previous section, when STunnel is
used, 2 separate HAProxy VIPs are required. This setup is illustrated in the following diagram.

N.B. If you require a single IP address with persistence across both ports 80 and 443, use the Tproxy /
HAProxy / Pound configuration described on the previous page.

Topology Requirements / Notes

• The RIPs must be on a different subnet to the VIP – this can achieved by using 2 IP addresses
assigned to a single interface, or two separate interfaces (in the above example, eth1 = 192.168.2.1
and eth0 = 192.168.4.1)

• Configure each Layer 7 VIP to listen on 1 port – e.g. port 80. Then configure the same Real Servers
for both VIPs

• TProxy for HAProxy must be enabled using the WUI option: Cluster Configuration > Layer 7 –
Advanced Configuration and setting Transparent Proxy to 'On'

• For VIP2, TProxy for STunnel must be enabled by checking the Proxy Protocol option when
creating or modifying the VIP

• For the STunnel VIP, TProxy must be enabled by checking the Set as Transparent Proxy option
when creating or modifying the VIP

• On the Real Servers, the default gateway must be configured to be an IP address on the load
balancer. When using a clustered pair, this should be a floating IP to allow failover to the slave

Chapter 6 – Configuring Load Balanced Services Page 145

 Appliance Administration Manual v8.1 Loadbalancer.org

Floating IPs
In order for the load balancer to function, the unit must physically own the Virtual IP address that the
clients are accessing before they get re-directed to a Real Server in the cluster. Floating IP(s) are added
automatically when new Virtual Services are created.
It's also possible to manually define floating IP(s) if required, this is normally only required when manually
configuring firewall marks or when using layer 4 NAT mode or TProxy where in both cases the load
balancer must be the default gateway for the Real Servers.
The Floating IP(s) are controlled by heartbeat to ensure that only one of the load balancer appliance's
(normally the master) owns the Floating IP(s) at any time.

To manually add a Floating IP:

 In the WUI, open Cluster Configuration > Floating IPs

 Specify the new floating IP

 Click Add Floating IP

IMPORTANT NOTE : When using a clustered pair, ensure that the slave also has a static IP
address assigned that's in the same subnet as the floating IP being added. Failure to do so will
result in heartbeat issues during a failover.

NOTE : Floating IPs are not deleted automatically when Virtual Services are removed or the
IP address is changed, this must be done manually.

Chapter 6 – Configuring Load Balanced Services Page 146

 Appliance Administration Manual v8.1 Loadbalancer.org

Server Feedback Agent

The load balancer can modify the weight (amount of traffic) of each server by gathering data from either a
custom agent or an HTTP server. For layer 4 VIPs the feedback method can be set to either agent or HTTP,
for Layer 7 VIPs, only the agent method is supported.

A telnet to port 3333 on a Real Server with the agent installed will return the current idle stats as an integer
value in the range 0 – 100. The figure returned can be related to CPU utilization, RAM usage or a
combination of both. This can be configured using the XML configuration file located in the agents
installation folder (by default C:\ProgramData\LoadBalancer.org\LoadBalancer).

The load balancer typically expects a 0-99 integer response from the agent which by default relates to the
current CPU idle state, e.g. a response of 92 would imply that the Real Servers CPU is 92% idle. The load
balancer will then use the formula (92/100*requested_weight) to find the new optimized weight.

N.B. The 'Requested Weight' is the weight set in the WUI for each Real Server.

For more information please also refer to the following blog article:

http://www.loadbalancer.org/blog/open-source-windows-service-for-reporting-server-load-back-to-
haproxy-load-balancer-feedback-agent

Windows Agent
The latest Windows feedback agent can be downloaded from:

http://downloads.loadbalancer.org/agent/loadbalanceragent.msi

To install the agent, run loadbalanceragent.msi on each Real Server

Click Next

Chapter 6 – Configuring Load Balanced Services Page 147

 Appliance Administration Manual v8.1 Loadbalancer.org

Select the installation folder and click Next

Click Next to start the installation

N.B. .NET Framework v3.5 is required by the agent and .NET Framework v4.0 is required by the Monitor
N.B. The agent should be installed on all Real Serves in the cluster

Starting the Agent

Once the installation has completed, you'll need to start the service on the Real Servers. The service is
controlled by the Feedback Agent Monitor program that is also installed along with the Agent. The monitor
can be accessed on the Windows server using: All Programs > Loadbalancer.org > Monitor. It's also
possible to start the service using the services snap-in – the service is called 'Loadbalancer CPU monitor'.

Chapter 6 – Configuring Load Balanced Services Page 148

 Appliance Administration Manual v8.1 Loadbalancer.org

• To start the service, click the Start button

• To stop the service, click the Stop button

Linux / Unix Agent

The Linux feedback agent files can be downloaded using the following links:

readme file: http://downloads.loadbalancer.org/agent/linux/v4.1/readme.txt

xinetd file: http://downloads.loadbalancer.org/agent/linux/v4.1/lb-feedback
feedback script: http://downloads.loadbalancer.org/agent/linux/v4.1/lb-feedback.sh

Installation

N.B. The agent files must be installed on all Real Servers, not the load balancer.

# Install xinetd
apt-get install xinetd (if not already installed)

# Insert this line into /etc/services

lb-feedback 3333/tcp # Loadbalancer.org feedback daemon

# Then
cp lb-feedback.sh /usr/bin/lb-feedback.sh
chmod +x /usr/bin/lb-feedback.sh
cp lb-feedback /etc/xinetd.d/lb-feedback
chmod 644 /etc/xinetd.d/lb-feedback

/etc/init.d/xinetd restart

# Testing
telnet 127.0.0.1 3333

Trying 127.0.0.1...
Connected to 127.0.0.1.
Escape character is '^]'.
95%

Connection closed by foreign host.

Chapter 6 – Configuring Load Balanced Services Page 149

 Appliance Administration Manual v8.1 Loadbalancer.org

Custom HTTP Agent

You can use any HTTP server responding on port 3333 to give feedback information to the load balancer.
The format of this information must be an integer number of 0-100 without any header information.
Using this method you can generate a custom response based on your applications requirements i.e. a
mixture of memory usage, IO, CPU etc.

Configuration
As mentioned, both layer 4 and layer 7 VIPs can be configured to use the feedback agent. To Configure
Virtual Services to use Agent / HTTP Feedback follow the steps below:

• Go to Cluster Configuration > Layer 4 - Virtual Services

or
Layer 7 - Virtual Services

• Click Modify next to the Virtual Service

• Change the Feedback Method to either Agent or HTTP for layer 4 VIPs

• Change the Feedback Method to Agent for layer 7 VIPs

• Click Update

• Reload / restart services as prompted

Chapter 6 – Configuring Load Balanced Services Page 150

 Appliance Administration Manual v8.1 Loadbalancer.org

Configuring VIPs & RIPs via Script & Command Line

Configuring L4 & L7 Services using the CLI Script (lbcli)

Action Category Action Example Command

Overview Drain a server lbcli --action drain --vip <VIP Name> --rip <RIP Name>
Actions:
Halt a server lbcli --action halt --vip <VIP Name> --rip <RIP Name>
Online a server lbcli --action online --vip <VIP Name> --rip <RIP Name>
VIP actions: Add a VIP Layer 4 VIP
lbcli --action add-vip --layer 4 --vip_type <ipv4|ipv6> --vip <VIP
Name> --ip <VIP IP Address> --ports <ports> --forwarding <gate|
masq|ipip> --protocol <tcp|udp>

Layer 7 VIP
lbcli --action add-vip --layer 7 --vip_type <ipv4|ipv6> --vip <VIP
Name> --ip <VIP IP Address> --ports <ports> --mode <http|tcp>

Delete a VIP lbcli --action delete-vip --vip <VIP Name>

Edit a VIP *Advanced option* - Please ask for assistance from Support if you
need to use this option
RIP actions: Add a RIP Layer 4 RIP
lbcli --action add-rip --vip <VIP Name> --rip_type <ipv4|ipv6> --rip
<RIP Name> --layer 4 --ip <RIP IP Address> --port <Port Value>
--weight <Weight value> --minconn <minconn> --maxconn
<maxconn>

Layer 7 RIP
lbcli --action add-rip --vip <VIP Name> --rip <RIP Name> --layer 7
--ip <RIP IP Address> --port <Port value> --rip_type <ipv4|ipv6>
--weight <Weight value>
Delete a RIP lbcli --action delete-rip --vip <VIP Name> --rip <RIP Name>
Edit a RIP *Advanced option* - Please ask for assistance from Support if you
need to use this option
Floating IP Add a FIP lbcli --action add-floating-ip --ip <IP Address>
actions:
Delete a FIP lbcli --action delete-floating-ip --ip <IP Address>
Service actions: Restart HAProxy lbcli --action restart-haproxy
Reload HAProxy lbcli --action reload-haproxy
Restart lbcli --action restart-ldirectord
Ldirectord
Reload lbcli --action reload-ldirectord
Ldirectord
Generate lbcli --action support-download
Support Archive

N.B. The above help information is also displayed when typing the following command:

lbcli ––action help

Chapter 6 – Configuring Load Balanced Services Page 151

 Appliance Administration Manual v8.1 Loadbalancer.org

Running lbcli from a remote Linux Host:

These commands can be run from a remote Linux host. This example halts VIP1 / RIP1 :

ssh [email protected] "lbcli --action halt --vip L72 --rip RIP_Name"

Running lbcli from a remote Windows Host:

These commands can be run from a remote Windows host. This example halts VIP1 / RIP1 :

plink -pw loadbalancer [email protected] "lbcli --action halt --vip VIP1 --rip RIP1"

Notes:

1. PuTTy must be installed to use the plink command

(see: http://www.chiark.greenend.org.uk/~sgtatham/putty/download.html)

2. 'loadbalancer' is the default password for the root user

3. 192.168.111.42 is the IP address of the load balancer

Chapter 6 – Configuring Load Balanced Services Page 152

 Appliance Administration Manual v8.1 Loadbalancer.org

Configuring Layer 4 Services using ipvsadm

For layer 4 services, the ipvsadm command can also be used. Several examples are provided below.

Add a TCP based Virtual Service & use weighted round robin scheduling:
ipvsadm -A -t 192.168.65.192:80 -s wrr

Add a TCP based Real Server in DR mode:

ipvsadm -a -t 192.168.65.192:80 -g -r 192.168.70.196:80

Add a TCP based Real Server in NAT mode:

ipvsadm -a -t 192.168.65.192:80 -m -r 192.168.70.196:80

Add a UDP based Virtual Service & use weighted least connection scheduling:
ipvsadm -A -u 192.168.65.192:80 -s wlc

Add a UDP based Real Server in DR mode:

ipvsadm -a -u 192.168.65.192:80 -g -r 192.168.70.196:80

Delete a TCP based Virtual Service:

ipvsadm -D -t 192.168.65.180:80

Delete a TCP based Real Server:

ipvsadm -d -t 192.168.65.122:80 -r 192.168.70.134:80

View the current running config:

ipvsadm -ln

IP Virtual Service version 1.2.1 (size=4096)

Prot LocalAddress:Port Scheduler Flags
-> RemoteAddress:Port Forward Weight ActiveConn InActConn
TCP 192.168.65.120:80 rr
-> 192.168.70.130:80 Route 1 0 0
-> 192.168.70.131:80 Route 1 0 0
TCP 192.168.65.122:80 rr
-> 192.168.70.132:80 Mass 1 0 0
-> 192.168.70.133:80 Mass 1 0 0

Chapter 6 – Configuring Load Balanced Services Page 153

 Appliance Administration Manual v8.1 Loadbalancer.org

Configuring Layer 7 Services using Linux Socket Commands

For layer 7 HAProxy VIPs, the socat socket command can also be used as shown in the examples below.

To take a server offline:

echo "disable server VIP_Name/RIP_Name" | socat unix-connect:/var/run/haproxy.stat stdio

To bring a server online:

echo "enable server VIP_Name/RIP_Name" | socat unix-connect:/var/run/haproxy.stat stdio

To set the weight of a Real Server:

echo "set weight VIP_Name/RIP_Name 0" | socat unix-connect:/var/run/haproxy.stat stdio

To view HAProxy's running configuration:

echo "show info" | socat unix-connect:/var/run/haproxy.stat stdio

To clear HAProxy's statistics:

echo "clear counters all" | socat unix-connect:/var/run/haproxy.stat stdio

N.B. Other examples can be found by searching for “Unix Socket Commands” at the following link:

http://haproxy.1wt.eu/download/1.6/doc/configuration.txt

IMPORTANT NOTE : Please note that since these changes are being made directly to the
running configuration, the services that are displayed in the System Overview will no longer
match the running configuration when ipvsadm / socat commands are used.

Using the lbcli command does not have this disadvantage and the System Overview will
show the correct VIP and RIP status.

NOTE : For additional assistance don't hesitate to contact: [email protected].

Chapter 6 – Configuring Load Balanced Services Page 154

Appliance Administration Manual v8.1 Loadbalancer.org

Chapter 7 – Web Application Firewall (WAF)

Chapter 7 – Web Application Firewall (WAF) Page 155

 Appliance Administration Manual v8.1 Loadbalancer.org

Introduction
The Web Application Firewall (WAF) is based on the Modsecurity Open Source Project.

The default vulnerability rule-set is based on the “OWASP top 10”. This defines 10 areas of vulnerability that
can effect Web Applications. These are summarised in the table below:

Category Description
A1 - Injection Injection flaws, such as SQL, OS, and LDAP injection occur when
untrusted data is sent to an interpreter as part of a command or query.
The attacker’s hostile data can trick the interpreter into executing
unintended commands or accessing data without proper
authorization.
A2 - Broken Authentication and Application functions related to authentication and session
Session Management management are often not implemented correctly, allowing attackers
to compromise passwords, keys, or session tokens, or to exploit other
implementation flaws to assume other users’ identities.
A3 - Cross-Site Scripting (XSS) XSS flaws occur whenever an application takes untrusted data and
sends it to a web browser without proper validation or escaping. XSS
allows attackers to execute scripts in the victim’s browser which can
hijack user sessions, deface web sites, or redirect the user to malicious
sites.
A4 - Insecure Direct Object A direct object reference occurs when a developer exposes a
References reference to an internal implementation object, such as a file,
directory, or database key. Without an access control check or other
protection, attackers can manipulate these references to access
unauthorized data.
A5 - Security Misconfiguration Good security requires having a secure configuration defined and
deployed for the application, frameworks, application server, web
server, database server, and platform. Secure settings should be
defined, implemented, and maintained, as defaults are often insecure.
Additionally, software should be kept up to date.
A6 - Sensitive Data Exposure Many web applications do not properly protect sensitive data, such as
credit cards, tax IDs, and authentication credentials. Attackers may
steal or modify such weakly protected data to conduct credit card
fraud, identity theft, or other crimes. Sensitive data deserves extra
protection such as encryption at rest or in transit, as well as special
precautions when exchanged with the browser.
A7 - Missing Function Level Most web applications verify function level access rights before
Access Control making that functionality visible in the UI. However, applications need
to perform the same access control checks on the server when each
function is accessed. If requests are not verified, attackers will be able
to forge requests in order to access functionality without proper
authorization.
A8 - Cross-Site Request Forgery A CSRF attack forces a logged-on victim’s browser to send a forged
(CSRF) HTTP request, including the victim’s session cookie and any other
automatically included authentication information, to a vulnerable
web application. This allows the attacker to force the victim’s browser
to generate requests the vulnerable application thinks are legitimate
requests from the victim.
A9 - Using Components with Components, such as libraries, frameworks, and other software
Known Vulnerabilities modules, almost always run with full privileges. If a vulnerable
component is exploited, such an attack can facilitate serious data loss
or server takeover. Applications using components with known

Chapter 7 – Web Application Firewall (WAF) Page 156

 Appliance Administration Manual v8.1 Loadbalancer.org

vulnerabilities may undermine application defenses and enable a

range of possible attacks and impacts.
A10 - Unvalidated Redirects and Web applications frequently redirect and forward users to other pages
Forwards and websites, and use untrusted data to determine the destination
pages. Without proper validation, attackers can redirect victims to
phishing or malware sites, or use forwards to access unauthorized
pages

More details can be found here : https://www.owasp.org/index.php/Top_10_2013-Top_10

Implementation Concepts
When a WAF gateway is created on the load balancer, the data path is automatically modified so that the
WAF becomes the initial connection point for inbound client connections as illustrated below:

Data flow without WAF deployed

Load Balancer Web

Server 1
80
Layer 7
VIP

Web
Server 2

Modified data flow once WAF is deployed

Load Balancer Web

Server 1
80
WAF Layer 7
Gateway VIP

Web
Server 2

Chapter 7 – Web Application Firewall (WAF) Page 157

 Appliance Administration Manual v8.1 Loadbalancer.org

NOTES:

• When defining a WAF Gateway on the load balancer, the associated layer 7 VIP must be selected
from a drop-down list. This enables the WAF to be automatically configured to listen on the same
TCP socket as the original layer 7 VIP
The WAF gateway is then automatically configured to forward packets to the original layer 7 VIP

• Each WAF gateway is associated with one layer 7 VIP

• Once the WAF gateway is defined, the Label, IP Address, Port and Protocol of the associated layer 7
VIP cannot be edited to ensure the association remains intact. If changes to these settings are
required, remove the WAF, make the changes, then recreate the WAF

• Each WAF gateway is comprised of an additional layer 7 VIP which acts as the WAF front-end and
an Apache/ModSecurity config. Both are auto-created when the WAF Gateway is configured

WAF Gateway Configuration

Initial Setup
For reasons mentioned in the previous section, the layer 7 VIP must be created first, then the WAF gateway.

Step 1 – Create the Layer 7 VIP

• Using the WUI open Cluster Configuration > Layer 7 – Virtual Services and click Add a new Virtual
Service

• Enter a suitable Label (name) for the VIP, e.g. HTTP-Cluster

• Enter a valid IP address, e.g. 192.168.110.46

• Enter a valid port, e.g. 80

• Click Update

Step 2 – Define the associated Real Servers (RIPs)

• Using the WUI open Cluster Configuration > Layer 7 – Real Servers and click Add a new Real
Server next the the VIP just created

Chapter 7 – Web Application Firewall (WAF) Page 158

 Appliance Administration Manual v8.1 Loadbalancer.org

• Enter a suitable Label (name) for the RIP, e.g. Web1

• Enter a valid IP address, e.g. 192.168.110.241

• Enter a valid port, e.g. 80

• Click Update

Step 3 – Define the WAF Gateway

• Using the WUI open Cluster Configuration > WAF - Gateway and click Add a new WAF gateway

• Select the VIP created in step 1 in the drop down

• Enter a suitable Label (name) for the WAF, e.g. WAF1

• Leave other options at their default settings

• Click Update

Step 4 – Reload Services to Apply the new Settings

• Click System Overview in the WUI

• Reload the services (Apache and HAProxy) as prompted in the blue message box

Chapter 7 – Web Application Firewall (WAF) Page 159

 Appliance Administration Manual v8.1 Loadbalancer.org

Step 5 – View Configured Services

• The original layer 7 VIP and the auto created layer 7 WAF front-end VIP are now displayed in the
system overview as shown below:

WAF Gateway Operating Mode

By default, the WAF Gateway only logs any breaches of the ModSecurity rules, it doesn't block any
requests.

The WAF gateway should initially be left in this mode so that any rule matches are logged. If there are no
false positives, blocking mode can be enabled to reject any malicious requests and respond with a 403
Forbidden response.

To enable blocking mode:

• Using the WUI open Cluster Configuration > WAF – Gateway and click Modify next to the relevant
WAF

• Enable the Rule Engine Traffic Blocking checkbox

• Click Update

• Click System Overview in the WUI

• Reload the services (Apache and HAProxy) as prompted in the blue message box

WAF Gateway Rules

Rules can easily be switched off if required. This maybe required if the default settings prove to restrictive.

To disable rules:

• Using the WUI open Cluster Configuration > WAF – Manual Configuration

• Select the relevant WAF in the drop-down

Chapter 7 – Web Application Firewall (WAF) Page 160

 Appliance Administration Manual v8.1 Loadbalancer.org

• Add an extra line specifying the rule to disable

e.g.
SecRuleRemoveById 960022

N.B. The rule ID can be obtained from the logs whilst in non blocking mode. For more details on
viewing the logs see the next section – WAF Gateway Monitoring

• Click Update

• Click System Overview in the WUI

• Reload Apache as prompted in the blue message box

Browsing by IP Address

The default rules block browsing by IP address. e.g. http://192.168.110.10/. This particular rule can be
disabled by going to Cluster Configuration > WAF - Manual Configuration, selecting the WAF in the
dropdown, then un-commenting the following line , i.e. removing the #

#SecRuleRemoveById 960017

Then reloading Apache as directed in the blue message box.

Any rule can be excluded in this way, as long as you know the ID, this can be obtained from the log entry
as explained in the next section.

Chapter 7 – Web Application Firewall (WAF) Page 161

 Appliance Administration Manual v8.1 Loadbalancer.org

WAF Gateway Logging & Monitoring

The WAF always logs malicious requests. The actual log entry depends on whether the WAF is running in
logging only mode or blocking mode.

To View the log:

• In the WUI select : Logs > WAF Logs

• In the drop-down select Error <WAF_NAME>

Example Log Entries:

1 - Example log entry (LOGGING ONLY mode)

[Thu Aug 13 14:36:10 2015] [error] [client 192.168.64.7] ModSecurity: Warning. Operator GE
matched 3 at TX:sqli_select_statement_count. [file
"/etc/httpd/modsecurity.d/activated_rules/modsecurity_crs_41_sql_injection_attacks.conf"] [line
"108"] [id "981317 "] [rev "2"] [msg "SQL SELECT Statement Anomaly Detection Alert"] [data
"Matched Data: X-Forwarded-For found within TX:sqli_select_statement_count: 4"] [ver
"OWASP_CRS/2.2.6"] [maturity "8"] [accuracy "8"] [tag
"OWASP_CRS/WEB_ATTACK/SQL_INJECTION"] [tag "WASCTC/WASC-19"] [tag
"OWASP_TOP_10/A1"] [tag "OWASP_AppSensor/CIE1"] [tag "PCI/6.5.2"] [hostname
"192.168.111.235"] [uri "/"] [unique_id "VcyrWn8AAAEAAA@CCC8AAAAB"]

In this example, the matching rule is: 981317 as highlighted above

2 - Example log entry (BLOCKING mode)

[Thu Aug 13 14:35:03 2015] [error] [client 192.168.64.7] ModSecurity: Access denied with code
403 (phase 2). Operator GE matched 3 at TX:sqli_select_statement_count. [file
"/etc/httpd/modsecurity.d/activated_rules/modsecurity_crs_41_sql_injection_attacks.conf"] [line
"108"] [id "981317 "] [rev "2"] [msg "SQL SELECT Statement Anomaly Detection Alert"] [data
"Matched Data: X-Forwarded-For found within TX:sqli_select_statement_count: 4"] [ver
"OWASP_CRS/2.2.6"] [maturity "8"] [accuracy "8"] [tag
"OWASP_CRS/WEB_ATTACK/SQL_INJECTION"] [tag "WASCTC/WASC-19"] [tag
"OWASP_TOP_10/A1"] [tag "OWASP_AppSensor/CIE1"] [tag "PCI/6.5.2"] [hostname
"192.168.111.235"] [uri "/"] [unique_id "VcyrF38AAAEAAAMYBpcAAAAA"]

In this example, the matching rule is also: 981317 as highlighted above

The difference here is that access was denied as highlighted

Chapter 7 – Web Application Firewall (WAF) Page 162

 Appliance Administration Manual v8.1 Loadbalancer.org

Modifying Default Actions

Default actions can easily be modified is required, a good example is to modify the response when access
is denied. By default a 403 (forbidden) response is returned to the requesting client. This can be changed
to redirect to a different URL using the SecDefaultAction as detailed below.

To customize default behavior:

• Using the WUI go to Cluster Configuration > WAF – Manual configuration

• Using the drop-down at the top of the page, select the required WAF

• In the Edit Window, add the following lines at the bottom of the page as shown below:
SecDefaultAction "phase:1,deny,log,redirect:https://www.yourdomain.com/pageforbidden.html"
SecDefaultAction "phase:2,deny,log,redirect:https://www.yourdomain.com/pageforbidden.html"

• Click Update

• Reload the services (Apache and HAProxy) as prompted in the blue message box at the top of the
screen

NOTE : For more information, please refer to the ModSecurity Reference Manual.

Chapter 7 – Web Application Firewall (WAF) Page 163

Appliance Administration Manual v8.1 Loadbalancer.org

Chapter 8 – Real Server Health Monitoring & Control

Chapter 8 – Real Server Health Monitoring & Page 164

Control
 Appliance Administration Manual v8.1 Loadbalancer.org

Configuring Health Checks

The appliance supports a range of health-check options to check and verify the health of Real Servers.
These range from simple ping checks to more complex negotiate options to determine that the underlying
daemon / service is running. The specific options available depend on whether services are deployed at
Layer 4 or Layer 7, details of both are covered in the following sections.

Heath Checks for Layer 4 Services

At layer 4, Real Server health checking is provided by Ldirectord. This is integrated into Loadbalancer.org
appliances and allows a full range of options to check that Real Servers are operational.

To configure health checks use the WUI option: Cluster Configuration > Layer 4 - Virtual Services > Modify
The exact options available depend on the check type selected. For the default (Connect to port), one field
is required:

As the drop-down is changed, the field list changes. The full list of options is shown below:

Default Health Check

By default, a TCP connect health check is used for newly created layer 4 Virtual Services.

Check Types

Negotiate – Sends a request and looks for a specific response (see Negotiate Check Service below)
Connect to port – Just do a simple connect to the specified port/service & verify that it's able to accept a
connection
Ping server – Sends an ICMP echo request packet to the Real Server
External check – Use a custom file for the health check. Specify the file path in the 'Check Command'
field.
No checks, always Off – All Real Servers are off
No checks, always On – All Real Servers are on (no checking)
5 Connects, 1 Negotiate – Do 5 connect checks and then 1 negotiate check
10 Connects, 1 Negotiate – Do 10 connect checks and then 1 negotiate check

Chapter 8 – Real Server Health Monitoring & Page 165

Control
 Appliance Administration Manual v8.1 Loadbalancer.org

Check Port

This can be used if the port to check is non standard, e.g., the service to check is HTTPS, but the port used
is 4443 instead of the standard 443. Leaving the field blank will cause the health-check to occur on the
port specified for the Real Server (note that in DR mode there is no Real Server port field since port re-
mapping is not possible, the port specified for the Virtual Service is used).

External Script Command

The custom check script, used with the external check type. The script should be placed in
/var/lib/loadbalancer.org/check, and given world read and execute permissions.
The following example illustrates how scripts can be constructed. This script uses the Linux command
'wget' to connect to the Real Server, then uses the Linux command 'grep' to look for the text 'OK' in the file
'check.txt'. The variable 'EXIT_CODE' which indicates a pass or fail is then returned to Ldirectord to control
whether the server should be left online or removed.
#!/bin/bash
# Variables
REALIP="$3"
PORT="$4"
REQUEST="check.txt"
RESPONSE="OK"

# Get the Page/File

wget -qO- --header="Host: host.domain.com" http://$REALIP:$PORT/$REQUEST |grep -e $RESPONSE
if [ "$?" -eq "0" ]; then
EXIT_CODE="0"
else
EXIT_CODE="1"
fi

exit $EXIT_CODE

Notes:

$3 and $4 are Ldirectord variables that are passed to the script. The following Ldirectord variables are
available and can be used as required:
$1 – the VIP address
$2 – the VIP port
$3 – the RIP address
$4 – the RIP port

Negotiate Check Service

If negotiate is selected as the check type, the following methods are valid:
HTTP – use HTTP as the negotiate protocol (also requires filename, path + text expected)
HTTPS – use HTTPS as the negotiate protocol (also requires filename, path + text expected)
HTTP Proxy – Use an HTTP proxy check
FTP – use FTP as the negotiate protocol (also requires login/password, filename in the default folder)
IMAP (IPv4 only) – use IMAP as the negotiate protocol (requires login/password)
IMAPS (IPv4 only) - use IMAPS as the negotiate protocol (requires login/password)
POP – use POP as the negotiate protocol (also requires login/password)

Chapter 8 – Real Server Health Monitoring & Page 166

Control
 Appliance Administration Manual v8.1 Loadbalancer.org

POPS – use POPS as the negotiate protocol (also requires login/password)

LDAP (IPv4 only) – use LDAP as the negotiate protocol (also requires username/password)
SMTP – use SMTP as the negotiate protocol
NNTP (IPv4 only) – use NNTP as the negotiate protocol
DNS – use DNS as the negotiate protocol
MySQL (IPv4 only) – use MySQL as the negotiate protocol (also requires username/password)
SIP – use SIP as the negotiate protocol (also requires username/password)
Simple TCP – Sends a request string to the server and checks the response
RADIUS (IPv4 only) – use RADIUS as the negotiate protocol (also requires username/password)

Virtual Host
If the Real Server will only respond to a URL or 'virtualhost' rather than an ip address, you can specify the
virtual host to request here.

Database Name
The database to use for the MySQL Negotiate check. This is a required option if MySQL is selected under
Negotiate Check Service above.

Radius Secret
The secret to use with Radius servers.

Login
The login name to use with negotiate checks where authentication is required.

Password
The password to use with negotiate checks where authentication is required.

Request to Send
This is used with negotiate checks and specifies the request to send to the server. The use of this
parameter varies with the protocol selected in Negotiate Check Service. With protocols such as HTTP and
FTP, this should be the object to request from the server. Bare filenames will be requested from the web or
FTP root. With DNS, this should be either a name to look up in an A record, or an IP address to look up in a
PTR record. With databases, this should be an SQL SELECT query (N.B. the response expected field in not
used by the SQL health check since the data returned in not read, the answer must simply be 1 or more
rows). With LDAP, this should be the search base for the query. The load balancer will perform an
(ObjectClass=*) search relative to this base. With Simple TCP, this should be a string to send verbatim to
the server.

Response Expected
This is the response that must be received for the negotiate check to be a success. The negotiate check
succeeds if the specified text (response) is found anywhere in the response from the web server when the
file specified in the Request to Send field is requested.
For example, a file called 'check.txt' could be placed in the default folder of the web server, this text file
could just have the text OK in the file, then when the negotiate check runs, it would look for a file called
'check.txt' containing OK. If found, the test would succeed, if not found it would fail and no new sessions
will be sent to that server.

Additional Health Check Settings

Additional Layer 4 health check options such as Check Interval, Failure Count etc. are available using the
WUI option: Cluster Configuration > Layer 4 – Advanced Configuration

Chapter 8 – Real Server Health Monitoring & Page 167

Control
 Appliance Administration Manual v8.1 Loadbalancer.org

NOTE : For more details of these options, please refer to page 109.

Health Checks for Layer 7 Services

At layer 7, Real Server health checking is handled by HAProxy. This is integrated into Loadbalancer.org
appliances and allows a range of options to check that Real Servers are operational.

To configure health checks use the WUI option: Cluster Configuration > Layer 7 - Virtual Services > Modify

As with Layer 4 Services, as the drop-down is changed, the field list changes.

Default Health Check

By default, a TCP connect health check is used for newly created layer 7 Virtual Services.

Check Types

Negotiate HTTP – Sends an HTTP request and looks for a specific response. Also set the Request to Send
& Response Expected fields.

Negotiate HTTPS – Sends an HTTPS request and looks for a specific response. Also set the Request to
Send & Response Expected fields.
N.B. If a negotiate HTTP or HTTPS check is used and Request to Send is configured but Response Expected
is left blank, the appliance looks for a 200 OK response from the real server.

Connect to port – Just do a simple TCP connect to the specified port/service & verify that it's able to
accept a connection

External Script – use a custom file for the health check. Specify the script path in the Check Script field.

MySQL - The check consists of sending two MySQL packets, one Client Authentication packet, and one
QUIT packet, to correctly close the MySQL session. It then parses the MySQL Handshake Initialization
packet and/or Error packet. It is a basic but useful test and does not produce error nor aborted connect on
the server. However, it does require adding an authorization in the MySQL table as follows:
use mysql; INSERT INTO user (Host,User) values ('<appliance-IP>','<username>'); flush privileges;
e.g.
use mysql; INSERT INTO user (Host,User) values ('192.168.1.1','probe'); flush privileges;

No checks, always On – All Real Servers are on (i.e. no checking)

Chapter 8 – Real Server Health Monitoring & Page 168

Control
 Appliance Administration Manual v8.1 Loadbalancer.org

Check Port
Specify a different port for health checks. If this field is left blank, health checks occur or the port specified
for each Real Server. If the VIP includes multiple ports (e.g. 80 & 443) by default the check occurs on the
first port listed. If a different port must be checked, it can be specified here.

Request to Send
Specify a specific file for the health check. Open the specified file and check for the response expected.
useful for checking a server sided script to check the health of the back-end application.

Response Expected
The content expected for a valid health check on the specified file. The response expected can be any
valid regular expression statement.

Request to Send / Response Expected Example:

If the server has a virtual directory called /customers, with a default page that contains the word 'welcome'
the required setup would be as follows:

Request to send: customers

Response expected: welcome

These settings would configure the following check directives in the HAProxy configuration file :

option httpchk GET /customers HTTP/1.0

http-check expect rstring welcome

N.B. the forward-slash character before 'customers' is added automatically

In this example, provided that the load balancer can access the page and see the text 'welcome', the
health-check would pass.

External Script Command

The custom check script, used with the external check type. The script should be placed in
/var/lib/loadbalancer.org/check, and given world read and execute permissions.
The following example illustrates how scripts can be constructed. This script uses the Linux command
'wget' to connect to the Real Server, then uses the Linux command 'grep' to look for the text 'OK' in the file
'check.txt'. The variable 'EXIT_CODE' which indicates a pass or fail is then returned to HAProxy to control
whether the server should be left online or removed.
#!/bin/bash
export PATH=/bin:/usr/bin:/sbin:/usr/sbin

# Variables
REALIP="$3"
PORT="$4"
REQUEST="check.txt"
RESPONSE="OK"

# Get the Page/File

wget -qO- --header="Host: host.domain.com" http://$REALIP:$PORT/$REQUEST |grep -qe $RESPONSE
if [ "$?" -eq "0" ]; then
EXIT_CODE="0"

Chapter 8 – Real Server Health Monitoring & Page 169

Control
 Appliance Administration Manual v8.1 Loadbalancer.org

else
EXIT_CODE="1"
fi

exit $EXIT_CODE

Notes:

$3 and $4 are HAProxy variables that are passed to the script. The following HAProxy variables are available
and can be used as required:

$1 – the VIP address

$2 – the VIP port
$3 – the RIP address
$4 – the RIP port

N.B. It's important that the commands are set the run in quite mode, i.e. no output. Otherwise HAProxy
may misinterpret the return data. This is achieved in the above example with -q options for the commands
'wget' and 'grep'.

Testing the script at the command line

A health-check script can be checked at the command line using the following format:

# ./<check-script-name> <$1> <$2> <$3> <$4>

e.g.

# ./check.sh 192.168.1.1 80 192.168.1.10 80

to check the return value, use the command:

# echo $?

A return value of 0 means the check has passed, 1 means it has failed.

Chapter 8 – Real Server Health Monitoring & Page 170

Control
 Appliance Administration Manual v8.1 Loadbalancer.org

Additional Health Check Settings

Additional Layer 7 health check options such as the check interval and failure count are available using the
WUI option: Cluster Configuration > Layer 7 – Advanced Configuration

NOTE : For more details of these options, please refer to page 124.

Simulating Health-Check Failures

It may not always be possible to take a server offline to check that health-checks are working correctly. In
these cases, firewall rules can be used. The following rules can be configured at the console, using SSH or
via the WUI under Local Configuration > Execute a Shell Command

To block access to a particular Real Server port:

iptables -A OUTPUT -p tcp --dport <Check Port> -d <REAL-SERVER-IP> -j DROP

e.g. iptables -A OUTPUT -p tcp --dport 80 -d 192.168.65.60 -j DROP

To re-enable access to a particular Real Server port:

iptables -D OUTPUT -p tcp --dport <Check Port> -d <REAL-SERVER-IP> -j DROP

e.g. iptables -D OUTPUT -p tcp --dport 80 -d 192.168.65.60 -j DROP

N.B. Make sure these rule are cleared after testing & verification is complete!

Disabling Health-Checks
In some cases it may be desirable to completely disable health checking and simply assume that the real
servers are up and working correctly. The can be configured simply by setting the health-check option to
No Checks, Always On – this applies to both layer 4 and layer 7 services.

Fallback Server Settings

The appliance uses NGINX for the local fallback server. The fallback server is activated under the following
conditions for Layer 4 & Layer 7 Virtual Services:

Layer 4

The fallback page is displayed when all Real Servers are unavailable and when all servers are taken offline
via the WUI. The fallback page can be hosted on the load balancer or on an external server. It can also be
configured to be a Layer 7 VIP. Set the Fallback Server option of the VIP accordingly.

Chapter 8 – Real Server Health Monitoring & Page 171

Control
 Appliance Administration Manual v8.1 Loadbalancer.org

Layer 7

For layer 7 VIPs the fallback page is displayed when all Real Servers are unavailable and when all servers are
taken offline via the WUI. The page can be hosted on the load balancer or on an external server. Set the
Fallback Server option of the VIP accordingly.

The local fallback page can be modified using the WUI option: Maintenance > Fallback Page

Notes:

• The local fallback server is an NGINX instance that by default listens on port 9081
• If a layer 4 VIP is added that listens on port 80, NGINX is automatically configured to listen on
ports 9081 & 80
• You can use any valid HTML for the default page, simply copy and paste the required HTML into
the Fallback Page using the Maintenance menu

Additional Fallback Server Notes:

Using the load balancers built-in Fallback Server:

• If you are using the load balancer for your holding page and your web servers are offline then the
local NGINX server is exposed to hacking attempts, if you are concerned about this you can
change the fallback server to be one of your internal servers.

Using an External, Dedicated Server:

• For DR mode the fallback server must be listening on the same port as the VIP (port re-mapping is
not possible with DR mode). Also, don't forget to solve the ARP problem for the dedicated fallback
server (see page 79)

• For NAT mode don't forget to set the default gateway of the fallback server to the internal IP of the
load balancer or when you have 2 appliances in a cluster, to a floating IP.

Chapter 8 – Real Server Health Monitoring & Page 172

Control
 Appliance Administration Manual v8.1 Loadbalancer.org

Using a Layer 7 VIP as the fallback server for Layer 4 VIPs:

• It's possible to set the fallback server for a layer 4 VIP to be a layer 7 VIP. This is especially useful in
WAN/DR site environments.
It also enables an external fallback server to be easily configured for Layer 4 VIPs – simply create a
fallback VIP and configure the fallback server as an associated RIP, then enable the MASQ option
for the Layer 4 VIP and set the fallback VIP as its fallback server. If all servers are down, requests
will then be routed via the Layer 7 VIP to the external server. If the layer 4 VIP is multi-port, specify
0 as the port for the fallback server. Requests will then be forwarded to the correct port.

Configuring Email Alerts

Email alerts can be configured for Virtual Services. This enables emails to be sent when Real Servers fail
there health-checks and are removed from the table, and also when they subsequently start to pass
checks and are re-added to the table.

Layer 4
At layer 4, settings can be configured globally that apply to all VIPs or individually to each VIP.

Global Settings
Once configured, these settings apply to all layer 4 VIPs by default.

To configure global email alert settings for layer 4 services:

 In the WUI, open Cluster Configuration > Layer 4 Advanced Configuration

Chapter 8 – Real Server Health Monitoring & Page 173

Control
 Appliance Administration Manual v8.1 Loadbalancer.org

 Enter an appropriate email address in the Email Alert Source Address field
e.g. [email protected]

 Enter an appropriate email address in the Email Alert Destination Address field
e.g. [email protected]

 Click Update

N.B. Make sure that you also configure an SMTP smart host using the WUI option: Local Configuration >
Physical Advanced configuration > Smart Host. This will be auto-configured (if a DNS server has already
been defined) to the MX record of the destination address domain name.

VIP Level Settings

Once configured, these settings apply to individual VIPs.

To configure VIP level email alerts:

 In the WUI, open Cluster Configuration > Layer 4 Advanced Configuration

 Enter an appropriate email address in the Email Alert Source Address field
e.g. [email protected]

 In the WUI, open Cluster Configuration > Layer 4 Virtual Service and click Modify next to the VIP to be
configured

 Enter an appropriate email address in the Email Alert Destination Address field
e.g. [email protected]

 Click Update

N.B. Make sure that you also configure an SMTP smart host using the WUI option: Local Configuration >
Physical Advanced configuration > Smart Host. This will be auto-configured (if a DNS server has already
been defined) to the MX record of the destination address domain name.

Chapter 8 – Real Server Health Monitoring & Page 174

Control
 Appliance Administration Manual v8.1 Loadbalancer.org

Layer 7
At layer 7, email settings must be configured globally rather than at the individual VIP level.

To configure global email alert settings for layer 7 services:

 In the WUI, open Cluster Configuration > Layer 7 Advanced Configuration

 Enter an appropriate email address in the Email Alert From field

e.g. [email protected]

 Enter an appropriate email address in the Email Alert To field

e.g. [email protected]

 Enter an appropriate email address in the Email Alert To field

e.g. mail.domain.com

 Click Update

Chapter 8 – Real Server Health Monitoring & Page 175

Control
 Appliance Administration Manual v8.1 Loadbalancer.org

Real Server Monitoring & Control using System Overview

Real Server Monitoring

The System Overview includes a visual display indicating the health status of all Virtual and Real Severs as
shown in the example below:

Clicking on each Virtual Service expands the view so that the associated Real Servers can also be seen:

The various colors used to indicate status are:

 Green – All Real Servers in the cluster are healthy

 Yellow – One or more Real Servers in the cluster has failed or has been taken offline using Halt or Drain

 Red – All Real Servers in the cluster have failed

 Blue – All Real Servers have been taken offline using Drain or Halt (see below)

 Purple / Green – Used to indicate that a particular VIP is used for HTTP to HTTPS redirection

This information is also displayed when clicking the system overview help button:

Chapter 8 – Real Server Health Monitoring & Page 176

Control
 Appliance Administration Manual v8.1 Loadbalancer.org

Real Server Control

The System Overview also enables the state of each Real Server to be controlled. Real Servers can be put
in the following modes:

 Drain – This option allows existing connections to close gracefully and prevents new connections

 Halt – This options prevents new connections and drops all existing connections immediately without
waiting

The screen shot below shows that RDS2 has been put into drain mode:

To bring RDS2 back online, click the Online (drain) link. If the server had been halted rather than drained,
the the link would be displayed as Online (Halt).

NOTE : If a particular Real Server is used in multiple VIPs you can choose to apply the
offline / online action to all relevant VIPs or only a single VIP. This simplifies taking Real
Servers offline for maintenance purposes.

NOTE : Halting or draining all Real Servers in a cluster at layer 7 and layer 4 activates the
fallback server.

Chapter 8 – Real Server Health Monitoring & Page 177

Control
 Appliance Administration Manual v8.1 Loadbalancer.org

Ordering of VIPs
The display order of configured VIPs can be changed either by clicking on the column heading, or by drag
and drop.

Sort by Column
If VIPs are ordered by a particular column, this is indicated using arrows next to the column heading as
shown below:

In this example, the VIPs are ordered alpha-numerically by Virtual Service name. To change the order, click
on the required column heading then click save. If you want to reverse the order for a particular column,
click that column heading again.

e.g. Clicking on the IP column heading shows the following:

Clicking on the IP column heading again changes the order to:

Once you've set the required order, click Save.

Chapter 8 – Real Server Health Monitoring & Page 178

Control
 Appliance Administration Manual v8.1 Loadbalancer.org

Drag & Drop

To re-order VIPs by drag and drop, simply click the mouse on any part of the VIP:

Then drag it to the required position:

And release it.

Once you've set the required order, click Save.

Chapter 8 – Real Server Health Monitoring & Page 179

Control
 Appliance Administration Manual v8.1 Loadbalancer.org

Real Server Control using the HAProxy Statistics Page

It's also possible to control layer 7 Real Servers using the HAProxy statistics page. By default this is not
enabled.

To enable this:

 In the WUI, open Cluster Configuration > Layer 7 – Advanced

 Enable the Advanced Stats option as shown below:

 Click Update

 Reload HAProxy using the button at the top of screen

With this setting, the HAProxy stats page has the ability to control the state of real servers as shown below:

Use the check-boxes to select the relevant Real Server(s), then select the required action in the drop-
down, then click Apply

Chapter 8 – Real Server Health Monitoring & Page 180

Control
Appliance Administration Manual v8.1 Loadbalancer.org

Chapter 9 – Appliance Clustering for HA

Chapter 9 – Appliance Clustering for HA Page 181

 Appliance Administration Manual v8.1 Loadbalancer.org

Introduction
Appliances can be deployed as single units or as a clustered pair.

NOTE : We always recommend deploying a clustered pair to avoid introducing a single point
of failure.

Clustered Pair Considerations

When configured as a clustered pair, the appliances work in Active-Passive mode. In this mode the active
unit (normally the master) handles all traffic under normal circumstances. If the active unit fails, the passive
unit (normally the slave) becomes active and handles all traffic.

Master / Slave Operation

Heartbeat
By default, heartbeat uses ucast over UDP port 6694 to communicate between the master and slave
appliances. The link enables the state of each to be monitored by the other and permits a failover to the
passive unit if the active unit should fail. For hardware appliances, it's also possible to configure ucast and
serial communication if required.

NOTE : For hardware appliances we recommend that heartbeat is configured to use both
ucast and serial when possible for added resilience. Once the serial cable is connected
between the appliances, the serial option must be enabled under: Cluster Configuration >
Heartbeat Configuration

Ping checks to a common node such as the default gateway can also be configured. If the active node
loses access to the ping node, the system will fail-over to the peer. However, if both nodes lose access, no
fail-over will occur.

Master Slave Replication

Once the master and slave are paired, all settings related to the layer 4 and layer 7 load balanced services
are automatically replicated from master to slave. This ensures that should the master unit fail, the slave is
already configured to run the same services. Note that replication of the configured load balanced services
from the master to the slave appliance occurs over the network using SSH/SCP.

Settings that are NOT Replicated to the Slave Appliance

Settings that are not replicated and therefore must be manually configured on the slave unit are listed
below:

• Hostname & DNS settings

• Network settings including IP addresses, bonding configuration and VLANs
• Routing configuration including default gateways and static routes
• Date & time settings
• Physical – Advanced Configuration settings including Internet Proxy IP address & port, Firewall
table size, SMTP relay and Syslog server
• SNMP settings
• Graphing settings

Chapter 9 – Appliance Clustering for HA Page 182

 Appliance Administration Manual v8.1 Loadbalancer.org

• Firewall Script & Firewall Lockdown Script settings

• Software updates

High Availability Configuration

Units can be combined into a clustered pair for high-availability and resilience. Points to note:

• Pairing should be performed on the unit that is to be the master appliance

• The master and slave appliance must be able to perform an ICMP echo request (ping) to each
other

• The master and slave appliance must be able to communicate with each other on TCP port 22

• The master and slave appliance must be able to communicate with each other on UDP port 6694
(or the selected custom port if this has been changed)

To Create an HA Pair (Add a slave)

• In the WUI, open: Cluster Configuration > High-Availability Configuration

• Specify the IP address and the loadbalancer users password (the default is 'loadbalancer') for the
slave (peer) appliance as shown above

• Click Add new node

• A warning will be displayed indicating that the pairing process will overwrite the new slave
appliance's existing configuration, click OK to continue

• The pairing process now commences as shown below:

Chapter 9 – Appliance Clustering for HA Page 183

Appliance Administration Manual v8.1 Loadbalancer.org

• Once complete, the following will be displayed:

• To finalise the configuration, restart heartbeat as prompted in the blue message box

N.B. Clicking the Restart Heartbeat button on the master appliance will also automatically restart
heartbeat on the slave appliance

To Break an HA Pair (Remove a slave)

• In the WUI of the master or slave appliance, open: Cluster Configuration > High-Availability
Configuration

• To break the pair, click the red Break button

Chapter 9 – Appliance Clustering for HA Page 184

Appliance Administration Manual v8.1 Loadbalancer.org

• Once the process is complete, the pairing configuration screen will be displayed:

• To complete the reconfiguration, restart the system services on both appliances as directed in the
blue message box

NOTES:

• Load balanced services will be momentarily interrupted as system services are restarted

• After the pair is broken, the slave will be left configured as a slave and any configured load
balanced services will remain.

• If you later want to use the slave as a master, use the Cluster Configuration > High Availability
Configuration menu option on the slave to setup a new pair. The slave will then be re-configured
as a master, and the added peer will be configured as a slave.

Chapter 9 – Appliance Clustering for HA Page 185

 Appliance Administration Manual v8.1 Loadbalancer.org

Promoting a Slave to Master

This is useful if the master unit fails and you'd like to change the now active slave to be a master, and then
add the repaired / replaced master back as a slave unit.

to promote a slave unit to become a master :

• In the WUI of the slave appliance, open: Cluster Configuration > High-Availability Configuration

• Click Promote

N.B. If the master is still up and operational, it will not be possible to promote the slave

• Once complete, the unit will be configured as a master

NOTE : Please refer to page 249 for details on how to recover from various failure scenarios.

Chapter 9 – Appliance Clustering for HA Page 186

 Appliance Administration Manual v8.1 Loadbalancer.org

Configuring Heartbeat

To configure Heartbeat:

• In the WUI of the Master appliance, open Cluster Configuration > Heartbeat Configuration
N.B. The screen shot below shows the configuration screen for a hardware appliance. The virtual
appliance does not have the serial option checkbox in the communications method section

Serial – Enable or disable heartbeat master/slave communication over the serial port. Ucast is the default
heartbeat communication method. However, if the load balancer pair is located in close proximity,
enabling serial communication in addition to ucast is recommended. This method requires a null modem
cable (one cable is supplied with each appliance) to be connected between the two load balancers in the
cluster. This enables heartbeat checks to utilize the serial port. When serial communication is disabled,
console access via the serial port is activated.

UDP Unicast – Enable or disable unicast heartbeat master/slave communication. This is the default
method of heartbeat communication and uses unicast UDP between master and slave, with a destination
port specified by the UDP Port for broadcast & unicast parameter. When unicast is enabled, the load
balancer determines the correct interface and IP addresses to use based upon the configured slave IP
address.

Chapter 9 – Appliance Clustering for HA Page 187

 Appliance Administration Manual v8.1 Loadbalancer.org

UDP Broadcast (Deprecated) – Enable or disable broadcast heartbeat master/slave communication, and
choose the interface. This option is deprecated - please migrate to Unicast. This method of heartbeat
communication uses broadcast UDP between master and slave, with a destination port specified by the
UDP Port for broadcast & unicast parameter. Care must be taken when using broadcast on multiple pairs of
load
balancers in the same network. Each high-availability pair must operate on a different UDP port if they are
not to interfere with each other. If heartbeat communication over the network is required, it is
recommended
that unicast be used in preference to broadcast.

UDP Port for unicast & broadcast – The UDP port number used by heartbeat for network
communication over unicast or broadcast. By default, heartbeat uses UDP port 6694 for unicast or
broadcast communication. If you have multiple load balancer pairs on the same subnet, and wish to use
broadcast, you will need to set each pair to a different UDP port.

Keep-alive message interval – Specify the number of seconds between keepalive pings. The Keepalive
setting must be less than the warntime and deadtime.

Dead peer timer – The number of seconds communication can fail before a fail over is performed. A very
low setting of deadtime could cause unexpected failovers.

Warning timer – If communication fails for this length of time write a warning to the logs. This is useful for
tuning your deadtime without causing failovers in production.

Test IP address – Specify one or more mutually accessible IP address to test network availability. A good
ping node to specify is the IP address of a router that both the master and slave node can access. If the
active node loses access to the ping node, the system will fail-over to the peer. However, if both nodes
lose access, no fail-over will occur. Multiple IP addresses may be given, separated by spaces or commas. In
this case, if any one address is reachable the routing test will pass.

Test time-out - Specify the time-out, in seconds, for the routing test. If a response is not received from the
test address within the time-out period, the route to that host will be considered dead.

Email Alert Destination Address – Specify the Email address to send heartbeat alerts. In the event of
failover the email address specified will receive an alert.

Automatic Fail-back – Enable/disable auto-failback. When the master returns to service after a failure,
should it become active again? This option controls the cluster behavior when the master returns to
service after a failure. With Automatic Fail-back enabled, the master will automatically return to active
status, taking back the floating IP addresses from the slave. With Automatic Fail-back disabled, the slave
will remain active and will retain the floating IP addresses. Fail-over back to the master must then be
controlled manually.

NOTE : Automatic Fail-back is disabled by default. Manual intervention is required to force

the repaired master to become active and the slave unit to return to passive mode. For more
details refer to page 191. Auto fail-back can be enabled if required using the WUI option:
Cluster Configuration > Heartbeat Configuration and enabling Automatic Fail-Back

Chapter 9 – Appliance Clustering for HA Page 188

 Appliance Administration Manual v8.1 Loadbalancer.org

Clustered Pair Diagnostics

Heartbeat State Diagnostics

The status of the appliance is shown at the top of the screen. For a working pair, the normal view is shown
below:

This shows that the master unit is active and that the heartbeat link is up between master & slave.

N.B. If no VIPs are defined, the status on master & slave appears as follows:

Other states:

Master | Slave Active | Passive Link this is a master unit, it's active, no slave unit has been
defined

Master | Slave Active | Passive Link this is a master unit, it's active, a slave has been defined
but the link to the slave is down.
Action : check & verify the heartbeat configuration

Master | Slave Active | Passive Link this is a slave unit, it's active (a failover from the master
has occurred) and the heartbeat link to the master has
been established

Master | Slave Active | Passive Link this is a master unit, a slave unit has been defined, but
the link is down (e.g. serial cable unplugged) so the state
cannot be determined. In this case the floating IP's may
be active on both units.
Action: check & verify the heartbeat configuration,

Chapter 9 – Appliance Clustering for HA Page 189

 Appliance Administration Manual v8.1 Loadbalancer.org

check the serial cable (if applicable), check heartbeat

logs & if required restart heartbeat on both units

Split Brain Scenarios

Split brain can occur if heartbeat on the master/slave clustered pair can no longer communicate with one
another. In this case both units will bring up the Virtual Services and the system status will look similar to
the following on both units:

When heartbeat communication is re-established, heartbeat will automatically attempt to resolve the split
brain and ensure that only one of the units is active. If heartbeat fails to do this automatically, the system
status will show as follows on both units:

The Take over button can then be used on either master or slave to attempt to force that unit to become
active.

Chapter 9 – Appliance Clustering for HA Page 190

 Appliance Administration Manual v8.1 Loadbalancer.org

Forcing Master/Slave Failover & Failback

To force the slave to become active & the master to become passive

Either use the Take over button in the slave's system overview:

N.B. Click the [Advanced] link to show this button.

Or run the following command on the slave:

/usr/local/sbin/hb_takeover.php all

To force the master to become active & the slave to become passive

Either use the Take over button on the master as explained above, or run the following command on the
master:

/usr/local/sbin/hb_takeover.php all

N.B. these commands can either be run on the console, via an SSH session or via the WUI using: Local
Configuration > Execute Shell Command

Chapter 9 – Appliance Clustering for HA Page 191

 Appliance Administration Manual v8.1 Loadbalancer.org

Testing & Verifying Master/Slave Replication & Failover

NOTE : It's very important to verify that master/slave failover occurs correctly before going live.
This proves the resilience of the HA cluster and makes you aware of the failover/failback process.

NOTE : When testing appliance fail-over, if heartbeat is configured to use only the serial link
don't just pull the serial cable out. This will not cause a fail-over but will cause a split brain (i.e.
both units active) to occur. Testing must be done by pulling both the network and serial cable (if
used) as detailed below.

STEP 1 - Verify Basic Settings for the clustered pair

1) On the master unit verify that the system status appears as follows:

2) On the slave unit verify that the system status appears as follows:

STEP 2 - Verify Replication

1) Verify that the load balanced services have been replicated to the slave unit, this can be done by using
either the View Configuration or Edit Configuration menus to validate that the same Virtual & Real Servers
exist on the slave as on the master.

STEP 3 - Verify Failover to the Slave (using the Take over button)

1) On the slave unit, click the [Advanced] option in the green information box, then click the Take Over
button

2) Verify that the slave's status changes to Active:

3) Verify that the master's status changes to Passive:

Chapter 9 – Appliance Clustering for HA Page 192

 Appliance Administration Manual v8.1 Loadbalancer.org

4) Using the WUI option: View Configuration > Network Configuration verify that the floating IPs
associated with the VIPs have been brought up on the slave unit and brought down on the master
e.g. the partial screen shot below from the View Network Configuration screen on the slave unit shows the
status of eth0:

This shows the secondary IP address 192.168.111.72 (the VIP address) is up and therefore the slave has
become active as intended.

STEP 4 - Verify Fallback to the Master (using the Take over button)

1) On the master unit, click the [Advanced] option in the green information box, then click the Take Over
button

2) Verify that the master's status has changed to Active:

3) Verify that the slave's status has changed to Passive:

4) Also, using the WUI option: View Configuration > Network Configuration verify that the floating IPs
associated with the VIPs have been brought up on the master unit and brought down on the slave (see
STEP 3 above for more details)

STEP 5 - Verify Failover to the Slave (when removing the network and serial cable from master)

1) Remove the network cable and serial cable (if applicable) from the master
2) verify that the slave's status has changed as follows:

Chapter 9 – Appliance Clustering for HA Page 193

 Appliance Administration Manual v8.1 Loadbalancer.org

This indicates that the slave is unable to communicate with the master. This means that either the master is
down, or is still up but is unreachable. In both cases the slave will go active.

3) On the slave using the WUI option: View Configuration > Network Configuration verify that the floating
IPs associated with the VIPs have been brought up (see STEP 3 above for more details)

STEP 6 - Verify normal operation resumes (when reconnecting the network & serial cable to master)

1) Reconnect the cables to the master

2) Verify that the master's status is set to Active:

3) Verify that the slave has changed to Passive:

4) Also, using the WUI option: View Configuration > Network Configuration verify that the floating IPs
associated with the VIPs have been brought up on the master unit and brought down on the slave

NOTE : If the power cable on the master had been removed rather than disconnecting the
network cable and serial cable (if applicable), once the master is brought back up the slave
would remain active and the master would come back up in a passive state. The Take over
button on the master would then need to be used to force the master to become active.

Chapter 9 – Appliance Clustering for HA Page 194

Appliance Administration Manual v8.1 Loadbalancer.org

Chapter 10 – Application Specific Settings

Chapter 10 – Application Specific Settings Page 195

 Appliance Administration Manual v8.1 Loadbalancer.org

FTP
FTP is a multi-port service in both active and passive modes:

active 20,21
passive 21,high_port

Layer 4 Virtual Services for FTP

When configuring a Virtual Service at layer 4 for FTP, simply setup a layer 4 VIP in the normal way and set
the Virtual Service / Real Server port field to port 21. Where Firewall Marks are required to handle other FTP
ports, these will be configured automatically. This applies to both active and passive mode. In NAT mode,
the ip_vs_ftp module is used to ensure that the client connects back via the load balancer rather than
attempting to connect directly to the Real Server.

N.B. Since the VIP is auto-configured for multi-port operation, ensure the checkport is set manually as
shown in the image below (typically port 21)

FTP Layer 4 Negotiate Health Check

You can modify the layer 4 Virtual Service so that rather than doing a simple socket connect check, it will
attempt to log into the FTP server and read a file for a specific response:

Key Points:

 Change the Check Type to Negotiate

 Ensure the Check Port is set to 21
 Make sure the Negotiate Check Service is set to FTP
 Specify a suitable login and password for the FTP server
 Specify the file to check using the Request to send field (defaults to the root directory)
 The file is parsed for the Response expected that you specify

Chapter 10 – Application Specific Settings Page 196

 Appliance Administration Manual v8.1 Loadbalancer.org

FTP Recommended Persistence Settings

When using multiple FTP servers in a cluster you should be aware of the effects of a client switching to a
different server. For sites that are download only, you generally don't need any special settings on the load
balancer as the connection will usually stay on the same server for the length of the connection. You may
however wish to force persistence to something sensible like 15mins.
If you are using the FTP servers for upload it is recommended to use a single FTP server for uploads and
then replicate the data to the read only cluster for downloads (or use a clustered file system). For upload it
is especially important to use persistence.
Automatically resuming a broken download is no problem even if you switch servers in a cluster on re-
connect. This is because the FTP resume functionality is client based and does not need any server session
information.

Layer 7 Virtual Services for FTP

Active Mode
In active mode, the FTP server connects back to the client, so it must be aware of the clients IP address. To
achieve this, TProxy must be enabled to make the load balancer transparent at layer 7. For this to work,
two subnets must be used – the Virtual Server (VIP) in one subnet, the RIPs (i.e. the FTP servers) in another.
For more details on TProxy, please refer to page 143 .
Also, to ensure that the client receives a connection from the same address that it established the control
connection to, an iptables SNAT rule must be defined in the firewall script for each FTP server. The format
of the required rule is as follows:

iptables -t nat -A POSTROUTING -p tcp -s <FTP-Server-IP> -j SNAT --to-source <FTP-VIP>

e.g.

iptables -t nat -A POSTROUTING -p tcp -s 10.20.1.1 -j SNAT --to-source 192.168.2.180

(one rule must be added for each FTP server in the cluster)

N.B. These rules can be added to the firewall script using the WUI option: Maintenance > Firewall Script

Active Mode – Key Points:

 Use separate subnets for the VIP & RIPs

 Enable TProxy
 Set the default gateway on the FTP servers to be an IP on the load balancer (ideally a floating IP to
permit failover to the slave unit)
 Setup a layer 7 VIP listening on port 21 & configure the RIPs also to listen on port 21
 Ensure the Layer 7 Protocol is set to 'Other TCP'
 Increase the default client & server HAProxy timeouts to 5 minutes
 Add the SNAT firewall rules for each FTP server

Chapter 10 – Application Specific Settings Page 197

Appliance Administration Manual v8.1 Loadbalancer.org

Windows 2008 Example

 Create a L7 VIP with the following settings changing the name and IP address as required:

 Define the FTP servers as RIPs for the VIP just created as illustrated below (these must be on a different
subnet to the VIP to enable TProxy to work correctly):

 Enable TProxy using the WUI option: Cluster Configuration > Layer 7 – Advanced Configuration

 Set Client Timeout and Real Server timeout to 5m (i.e. 5 minutes) using the WUI option: Cluster
Configuration > Layer 7 – Advanced Configuration

 Now restart HAProxy using the WUI option: Maintenance > Restart Services

 Define a SNAT rule for each FTP server using the WUI option: Maintenance > Firewall Script
e.g.
iptables -t nat -A POSTROUTING -p tcp -s 10.10.1.1 -j SNAT --to-source 192.168.2.180
iptables -t nat -A POSTROUTING -p tcp -s 10.10.1.2 -j SNAT --to-source 192.168.2.180

 Configure the default gateway on each FTP server to be the load balancer. Ideally this should be a
floating IP address to allow it to move between the master & slave appliance. This can be added using
the WUI option: Cluster Configuration > Floating IPs

 Active FTP clients should now be able to connect to the VIP address (192.168.2.180) and view the
directory listing successfully

Chapter 10 – Application Specific Settings Page 198

 Appliance Administration Manual v8.1 Loadbalancer.org

Passive Mode
In passive mode all connections are initiated by the client. The server passes the client a port to use for the
inbound data connection. By default, FTP serves can use a wide range of ports for the inbound connection
and it's often useful to limit this range. The following section “Limiting Passive FTP ports” on page 201
covers this for a range of OS's & FTP servers.
N.B. This method configures HAProxy to listen on port 21 (control channel) and all passive ports (data
channel)

Passive Mode – Key Points:

 It's sensible to use a controlled passive port range, this can be configured on the FTP server

 Configure the VIP to listen on port 21 and also the passive range selected, e.g. 50000-50100

 Configure the RIPs without specifying a port

 Ensure the Layer 7 Protocol is set to 'TCP Mode'

 If transparency is required (for passive mode this is optional), enable TProxy using the WUI option:
Cluster Configuration > Layer 7 – Advanced Configuration
N.B. If TProxy is enabled, make sure that the RIPs (i.e. the FTP servers) are located in a different subnet
to the Virtual Server (VIP). The default gateway on each FTP server must also be set to be an IP on the
load balancer – preferably a floating IP which then allows failover to the slave unit (see page 143 for
more details on using TProxy)

 Using the WUI option: Cluster Configuration > Layer 7 – Advanced Configuration increase the default
Client timeout & Real Server Timeout to 5m (i.e. 5 minutes)

 To ensure the correct address is passed back to the client, on each FTP server specify the external
address to be the VIP address.

e.g.

- for Windows 2008 use the External IP address of Firewall field

- for Linux vsftpd use the directive: pasv_address=xxx.xxx.xxx.xxx

- for Linux ProFTPd use the directive: MasqueradeAddress=xxx.xxx.xxx.xxx

Chapter 10 – Application Specific Settings Page 199

Appliance Administration Manual v8.1 Loadbalancer.org

Windows 2008 Example

 Create a L7 VIP with the following settings changing the name, IP address & passive port range as
required:

 Configure the VIP to listen on both the control port (21) and passive range (e.g. 50000-50100) as shown

 Define the FTP servers as RIPs for the VIP just created leaving the port field blanks as illustrated below:

 Set Client Timeout and Real Server timeout to 5m (i.e. 5 minutes) using the WUI option: Cluster
Configuration > Layer 7 – Advanced Configuration

 Now restart HAProxy using the WUI option: Maintenance > Restart Services

 On each FTP server using IIS Manager define the same passive port range and set the external IP
address to be the Virtual Server (VIP) address as shown in the example below:

N.B. The external IP address must be set to be the VIP address, this ensure that this IP address is passed
back to the client to use for the subsequent inbound connection

Chapter 10 – Application Specific Settings Page 200

 Appliance Administration Manual v8.1 Loadbalancer.org

 If TProxy is enabled, make sure the gateway of each FTP sever is set to be an IP on the load balancer
(preferably a floating IP to allow failover to the slave unit)

 Now restart both IIS and the Microsoft FTP Service on each FTP server

 Passive FTP clients should now be able to connect to the VIP address (192.168.2.180) and view the
directory listing successfully

Limiting Passive FTP Ports

Limiting passive ports allows your firewall to be more tightly locked down. The following sections show
how this is achieved for a range of Operating Systems / FTP servers.

For Windows 2008

Open the IIS Management console, highlight the server node, then double-click the FTP Firewall Support
icon.

The following screen will be displayed:

Specify a suitable range, in the example above this is 50000-50100

Chapter 10 – Application Specific Settings Page 201

 Appliance Administration Manual v8.1 Loadbalancer.org

IMPORTANT! - Make sure you restart IIS and the Microsoft FTP Service to apply these settings.

For Windows 2003

a) Enable Direct Metabase Edit

1. Open the IIS Management Console

2. Right-click on the Local Computer node
3. Select Properties
4. Make sure the Enable Direct Metabase Edit check-box is checked

b) Configure PassivePortRange via ADSUTIL script

1. Click Start, click Run, type cmd, and then click OK

2. Type cd Inetpub\AdminScripts and then press ENTER
3. Type the following command from a command prompt
adsutil.vbs set /MSFTPSVC/PassivePortRange "50000-50100"
4. Restart the FTP service

For Windows 2000

Configure PassivePortRange via the Registry Editor

1. Start Registry Editor (Regedt32.exe)

2. Locate the following registry key:
HKEY_LOCAL_MACHINE\System\CurrentControlSet\Services\Msftpsvc\Parameters\
3. Add a value named "PassivePortRange" (without the quotation marks) of type REG_SZ
4. Close Registry Editor
5. Restart the FTP service

(SP4 or higher must be installed for this to work)

N.B. The range that FTP will validate is from 5001 to 65535

For Linux

For vsftpd, the following line can be added to the vsftpd.conf file to limit the port range:

pasv_max_port – max is 65535

pasv_min_port – min is 1024

For proftpd, the following line can be added to the proftpd.conf file to limit the port range:

PassivePorts 50000 – 50100

For pureftpd, the following startup switch can be used:

-p --passiveportrange <min port:max port>

Chapter 10 – Application Specific Settings Page 202

 Appliance Administration Manual v8.1 Loadbalancer.org

Terminal Services / Remote Desktop Services

Layer 4 – IP Persistence
RDP is a TCP based service usually on port 3389. Clients will need to be sent to the same server to allow
reconnection to existing sessions. The persistence setting should be changed to suit your requirements. A
typical setting to use is persistence = 7200 (i.e. 7200s = 2 hours). This means that when a client reconnects
within this time, they will be sent to the same Terminal Server / Remote Desktop Server. If a client is idle for
more than 2 hours, then the load balancer will treat the next connection as a new connection and possibly
take them to a different server.

Layer 7 – Microsoft Connection Broker / Session Directory

It's possible to configure the load balancer to interact with Session Directory / Connection Broker by
enabling Routing Token Redirection mode. This mode allows the reconnection of disconnected sessions
by utilizing a routing token to enable the load balancer to re-connect the client to the correct server.
Simply create Layer 7 VIP as shown below:

Chapter 10 – Application Specific Settings Page 203

 Appliance Administration Manual v8.1 Loadbalancer.org

Layer 7 – RDP Cookies

The appliance also supports persistence based on RDP cookies. This method utilizes the cookie sent from
the client in the initial Connection Request PDU (mstshash). This cookie is created when the username is
entered at the first client login prompt (mstsc.exe). Note that if the username is not entered here, the
cookie is not created. An associated persistence entry is also created in a stick table on the load balancer
for each connection. If the cookie is not found, it will fallback to source IP persistence.

Again, persistence can be set as required, but as per the previous example 2 hours (120m) has been
configured in the example above.
Initial connections are distributed to the Real Servers based on the balance mode selected (defaults to
weighted least connection). Re-connecting clients utilize the stick table to return the client to the same
server first connected to. This enables clients to reconnect to their disconnected sessions.

NOTE : For additional information, please refer to the following Deployment Guides:

Remote Desktop Services Deployment Guide

Terminal Services Deployment Guide

Other Applications
The appliance is able to support virtually any TCP or UDP based protocol which enables most applications
to be load balanced. For a list of deployment guides currently available for popular applications such as
Microsoft Exchange, IIS, Lync etc., please refer to page 16 earlier in this manual.

NOTE : Don't hesitate to contact [email protected] for advice on load balancing

your application if it's not listed.

Chapter 10 – Application Specific Settings Page 204

Appliance Administration Manual v8.1 Loadbalancer.org

Chapter 11 – Configuration Examples

Chapter 11 – Configuration Examples Page 205

 Appliance Administration Manual v8.1 Loadbalancer.org

Introduction
This section presents three example configurations that illustrate how the appliance is configured.

Initial Network Settings

For details on configuring initial network settings and accessing the WUI please refer to page 35 and page
39.

Example 1 – One-Arm DR Mode (Single Appliance)

This DR (Direct Return) mode example has one Virtual Service (VIP) with two Real Servers (RIPs). It's a
straight forward deployment mode that can be used in many situations. It also offers the highest
performance because return traffic passes directly from the Real Servers to the client rather than passing
back via the load balancer.

Configuration Overview
 Configure Network Settings – a single Interface is needed, eth0 is normally used

 Define the Virtual Service (VIP) – all Real (back-end) Servers are accessed via this IP address

 Define the Real Servers (RIPs) – define the Real Servers that make up the cluster

 Implement the required changes to the Real Servers – for DR mode, the ARP issue must be
solved

Network Settings
N.B. this step can be skipped if all network settings have already been configured

Configure the various network settings as outlined below:

 Using the WUI open Local Configuration > Network Interface Configuration

 Specify the IP address & subnet mask for eth0 (normally eth0 is used for single-arm configurations
although this is not mandatory), e.g. 192.168.2.120/24

 Click Configure Interfaces

Chapter 11 – Configuration Examples Page 206

 Appliance Administration Manual v8.1 Loadbalancer.org

 Using the WUI open Local Configuration > Hostname & DNS

 Specify the DNS server(s)

 Click Update

 Using the WUI open Local Configuration > Routing

 Specify the Default Gateway

 Click Configure Routing

Virtual Service (VIP)

Next, configure the Virtual Service. This is the IP address that is presented to clients. Any packet arriving at
the load balancer with that IP address and port number will be forwarded to the the Real Servers
associated with the Virtual Service.

 Using the WUI open Cluster Configuration > Layer 4 – Virtual Services and click Add a new
Virtual Service

 Enter a suitable Label (name) for the VIP, e.g. ExVIP1

 Enter a valid IP address, e.g. 192.168.2.150

 Enter a valid port, e.g. 80

 Ensure that Forwarding Method is set to Direct Routing (N.B. this is the default)

Chapter 11 – Configuration Examples Page 207

 Appliance Administration Manual v8.1 Loadbalancer.org

Real Servers (RIPs)

Each Virtual Service requires a cluster of Real Servers (back-end servers) to forward the traffic to.

 Using the WUI open Cluster Configuration > Layer 4 – Real Servers and click Add a new Real
Server next to the relevant Virtual Service

 Enter a suitable Label (name) for the RIP, e.g. RIP1

 Enter a valid IP address, e.g. 192.168.2.151

N.B. A port is not required since port redirection is not possible in DR mode. The port used will be
the same as that configured for the VIP

 The weight defaults to 100 making the Real Server active immediately

 Leave Minimum Connections & Maximum Connections set to 0 which means unrestricted

 Click Update

 Repeat for the remaining Real Servers

Real Server Changes – Solve the ARP Problem

Since this example uses the one-arm DR mode load balancing method each Real Server requires the ARP
problem to be solved:

 Each Real Server must be configured to respond to its own IP address and the VIP address

 Each Real Server must be configured so that it only responds to ARP requests for its own IP
address, it should not respond to ARP requests for the VIP address – only the load balancer must
respond to these requests

NOTE : Failure to correctly configure the Real Servers to handle the ARP problem is the most
common problem in DR configurations. Please refer to page 79 for more details.

Chapter 11 – Configuration Examples Page 208

 Appliance Administration Manual v8.1 Loadbalancer.org

Basic Testing & Verification

Once configured, a few quick checks can be performed to verify the setup:

 Using System Overview check that the VIP & RIPs are shown as active (green)

 Using a browser, navigate to the VIP address, i.e. http://192.168.2.150 to verify that you can reach
the Real Servers via the Virtual Service

 Check Reports > Layer 4 Current Connections to ensure that client connections are reported in
state 'ESTABLISHED'. If connections are in state 'SYN_RECV', this normally indicates that the ARP
problem on the Real Servers has not been correctly solved

Chapter 11 – Configuration Examples Page 209

 Appliance Administration Manual v8.1 Loadbalancer.org

Example 2 – Two-Arm NAT Mode (Clustered Pair)

This example covers the process of configuring two load balancers (as a clustered pair) in NAT mode.

NOTE: Using two appliances configured as a clustered pair is Loadbalancer.org's recommended

configuration and ensures that no single point of failure is introduced

NOTE : When using two-arm NAT mode all Real Servers should be in the same subnet as the
internal interface of the load balancer and the default gateway on each Real Server must be
set to be the load balancer.

Configuration Overview
 Configure the Master's Network Settings – two Interfaces are needed, this can be either two
physical interfaces such as eth0 and eth1, or one physical interface and a secondary interface/alias

 Configure the Slave's Network Settings – two Interfaces are needed, this can be either two
physical interfaces such as eth0 and eth1, or one physical interface and a secondary interface/alias

 Configure the Master & Slave Heartbeat Settings – set the heartbeat comms method

 Define the Virtual Service (VIP) – all Real Servers are accessed via this IP address

 Define the Real Servers (RIPs) – define the Real Servers that make up the cluster

 Implement the required changes to the Real Servers – in NAT mode, the Real Servers default
gateway must be set to be the load balancer

Master Unit – Network Settings

 Using the WUI on the master unit, open Local Configuration > Network Interface Configuration

Chapter 11 – Configuration Examples Page 210

 Appliance Administration Manual v8.1 Loadbalancer.org

 Specify the IP address & mask for eth0 – normally eth0 is configured as the internal interface
although this is not mandatory, e.g. 192.168.2.120/24

 Specify the IP address & mask for eth1 – normally eth1 is configured as the external interface
although this is not mandatory, e.g. 192.168.20.120/24
N.B. For a VA make sure that the virtual NIC associated with eth1 is connected to the virtual switch.
By default only the first NIC is connected.

 Click Configure Interfaces

 Using the WUI open Local Configuration > Hostname & DNS

 Ensure that Role is set to master

 Ensure that the DNS server(s) are set correctly

 Click Update

 Using the WUI open Local Configuration > Routing

 Specify the Default Gateway, e.g. 192.168.254

 Click Configure Routing

Slave Unit – Network Settings

Configure the various network settings as outlined below:

 Using the WUI on the slave unit open Local Configuration > Network Interface Configuration

Chapter 11 – Configuration Examples Page 211

Appliance Administration Manual v8.1 Loadbalancer.org

 Specify the IP address & mask for eth0 – normally eth0 is configured as the internal interface
although this is not mandatory, e.g. 192.168.2.121/24

 Specify the IP address & mask for eth1 – normally eth1 is configured as the external interface
although this is not mandatory, e.g. 192.168.20.121/24

 Click Configure Interfaces

 Using the WUI open Local Configuration > Hostname & DNS

 Ensure that Role is set to slave

 Ensure that the DNS server(s) are set correctly

 Click Update
N.B. Once update is clicked the Hostname field will automatically change to lbslave

 Using the WUI open Local Configuration > Routing

Chapter 11 – Configuration Examples Page 212

Appliance Administration Manual v8.1 Loadbalancer.org

 Specify the default gateway, e.g. 192.168.2.254

 Click Configure Routing

Master Unit – Heartbeat Settings

 Using the WUI on the master unit open Cluster Configuration > Heartbeat Configuration

 Define the slave load balancers IP address in the Slave Load Balancer Address field, e.g.
192.168.2.121

 Set the heartbeat communications method as required. The default is UDP unicast.

 Click Modify Heartbeat Configuration, this will apply the heartbeat configuration on the local
master and copy and apply the heartbeat configuration to the slave

 Now click Restart Heartbeat as prompted in the blue commit changes box – this will restart
heartbeat both locally and on the slave unit to ensure that heartbeat synchronization occurs
successfully

Chapter 11 – Configuration Examples Page 213

 Appliance Administration Manual v8.1 Loadbalancer.org

NOTE : If Virtual Services have already been defined, you'll need to use the WUI option:
Maintenance > Backup & Restore > Synchronization > Synchronize Configuration with
Peer to copy all configured services from master to slave. If Virtual Services are setup after
the units have been paired, they are automatically copied over to the slave.

Checking the Status

A successfully configured clustered pair will display the following status:

On the Master unit:

On the Slave unit:

Virtual Service (VIP)

Next, configure the Virtual Service. This is the IP address that is presented to clients. Any packet arriving at
the load balancer with that IP address and port number will be forwarded to the the Real Servers
associated with the Virtual Service.

 Using the WUI open Cluster Configuration > Layer 4 – Virtual Services and click Add a new
Virtual Service

 Enter a suitable label (name) for the VIP, e.g. ExVIP2

 Enter a valid IP address, e.g. 192.168.2.150

 Enter a valid port, e.g. 80

 Ensure that Forwarding Method is set to NAT

 Click Update, this will save the VIP locally and also replicate it to the slave

Chapter 11 – Configuration Examples Page 214

 Appliance Administration Manual v8.1 Loadbalancer.org

Real Servers (RIP)

Each Virtual Service requires a cluster of Real Servers (back-end servers) to forward the traffic to.

 Open Cluster Configuration > Layer 4 – Real Servers and click Add a new Real Server

 Enter a suitable Label (name) for the RIP, e.g. RIP1

 Enter a valid IP address, e.g. 192.168.2.151

 Enter a valid port, e.g. 80

 Weight defaults to 100 making the Real Server active immediately

 Leave Minimum Connections & Maximum Connections set to 0 which means unrestricted

 Click Update, this will save the RIP locally and also replicate IT to the slave

 Repeat for the remaining Real Servers

Real Server Changes – Set the Default Gateway

When using NAT mode, each Real Servers default gateway must be changed to be the load balancer. For a
clustered pair, you must define an additional floating IP for this purpose. Then, if failover is required the
same IP will also be brought up on the slave.

To add a floating IP to use as the default gateway, use Cluster Configuration > Floating IP's.

Define the IP address that you'd like to use for the default gateway, then click Add Floating IP. Now
configure the default gateway on each Real Server to use this address.

Chapter 11 – Configuration Examples Page 215

 Appliance Administration Manual v8.1 Loadbalancer.org

Verify the Slave Configuration

To verify that the new VIP & RIP have been replicated correctly, open the WUI on the slave and open
Cluster Configuration > Layer 4 – Virtual Services and Cluster Configuration > Layer 4 – Real Servers and
check that your configuration appears there also. For a correctly configured pair, the VIPs and RIPs are
automatically replicated to the slave as they are defined on the master.
If not, double check that both units are configured correctly and that the IP address for the slave defined
on the master is correct. Then on the master open Maintenance > Backup & Restore and click Synchronize
Configuration with peer. This will force the VIPs & RIPs to be copied from the master to the slave, then
check again.

Basic Testing & Verification

A few quick checks can be performed to verify the configuration:

 On the master, use System Overview to check that the VIP & RIPs are shown as active (green)

 Using a browser, navigate to the VIP address, i.e. http://192.168.2.150 to verify that you can reach
the Real Servers via the Virtual Service

 On the master, check Reports > Layer 4 Current Connections to ensure that client connections are
reported in state 'ESTABLISHED'. If not, double-check that you have set the default gateway on all
Real Servers to be an IP address on the load balancer.

Chapter 11 – Configuration Examples Page 216

 Appliance Administration Manual v8.1 Loadbalancer.org

Example 3 – One-Arm SNAT Mode & SSL Termination (Single Appliance)

This example uses HAProxy and STunnel at layer 7. STunnel is used to terminate SSL on the load balancer.
STunnel then passes un-encrypted HTTP traffic to the HAProxy VIP / RIP cluster.

HAProxy does not offer the raw throughput of layer 4, but is still a high performance solution that is
appropriate in many situations.

N.B. Pound can also be used for SSL termination, although STunnel is the preferred and default method

In this example it's assumed that the Real Server application has not been designed to track & share session
details between Real Servers. Therefore, cookie based persistence will be enabled on the load balancer to
ensure that clients connect to the same Real Server on each subsequent connection (within the
persistence timeout window). If persistence is not configured then new connections may get distributed to
a different Real Server which may result in failure of the application.

NOTE : Because HAProxy is a full proxy, any server in the cluster can be on any accessible
subnet including across the Internet or WAN.

NOTE : In this mode, no changes are required to the Real Servers.

NOTE : We generally recommend that SSL is terminated on the real serves rather than on the
load balancer. This ensures that the SSL load is distributed and also ensures scalability.

Configuration Overview

 Configure Network Settings – A single Interface is needed, eth0 is normally used

 Define the Virtual Service (VIP) – All Real Servers are accessed via this IP address

 Define the Real Servers (RIPs) – Define the Real Servers that make up the cluster

 Configure SSL Termination – Configure STunnel for SSL termination

Network Settings

Configure the various network settings as outlined below:

 Using the WUI open Local Configuration > Network Interface Configuration

Chapter 11 – Configuration Examples Page 217

Appliance Administration Manual v8.1 Loadbalancer.org

 Specify the IP address & mask for eth0 – normally eth0 is used for one-arm configurations
although this is not mandatory, e.g. 192.168.2.120/24

 Click Configure Interfaces

 Using the WUI open Local Configuration > DNS & Hostname

 Specify the DNS server(s)

 Click Update

 Using the WUI open Local Configuration > Routing

 Specify the Default Gateway, e.g. 192.168.2.254

 Click Configure Routing

Chapter 11 – Configuration Examples Page 218

 Appliance Administration Manual v8.1 Loadbalancer.org

Virtual Service (VIP)

Next, configure the Virtual Service. This is the IP address that is presented to clients. Any packet arriving at
the load balancer with that IP address and port number will be handled by the Real Servers associated with
the Virtual Service.

 Using the WUI open Cluster Configuration > Layer 7 – Virtual Services and click Add a new Virtual
Service

 Enter a suitable Label (name) for the VIP, e.g. ExVIP3

 Enter a valid IP address, e.g. 192.168.2.150

 Enter a valid port, e.g. 80

 Click Update

Real Servers (RIP)

Each Virtual Service requires a cluster of Real Servers (back-end servers) to forward the traffic to.

 Using the WUI open Cluster Configuration > Layer 7 – Real Servers and click Add a new Real
Server

 Enter a suitable Label (name) for the RIP, e.g. RIP1

 Enter a valid IP address, e.g. 192.168.2.151

N.B. In this mode it's possible to have a different port for the RIP than was configured for the VIP, in
this example both are the same

 Enter a valid port, e.g. 80

Chapter 11 – Configuration Examples Page 219

 Appliance Administration Manual v8.1 Loadbalancer.org

 The Weight defaults to 100 making Real Servers active as soon as HAProxy is restarted

 Click Update

 Repeat for the remaining Real Servers

 Restart HAProxy to apply the new settings using the link provided in the blue box

SSL Termination
An STunnel (default) or Pound VIP can be configured on port 443 using the same IP address as the Layer 7
VIP created previously. This allows a single IP address to be used.

 Open Cluster Configuration > SSL Termination and click Add a new Virtual Service

 Enter a suitable Label (name) for the VIP, e.g. ExSSL

 Set Virtual Service IP address to be the same as the layer 7 VIP created earlier, i.e. 192.168.2.150

 Leave Virtual Service Port set to 443

 Set Backend Virtual Service IP address to be the same as the layer 7 VIP created earlier, i.e.
192.168.2.150

Chapter 11 – Configuration Examples Page 220

 Appliance Administration Manual v8.1 Loadbalancer.org

 Leave Backend Virtual Service Port set to 80

 Leave the other settings at their default values

 Click Update

 Restart STunnel to apply the new settings using the link provided in the blue box

When creating the SSL Virtual Service, by default a self-signed certificate is used. This is ideal for testing but
needs to be replaced for live deployments.

NOTE : For more detailed information on SSL termination please refer to page 127.

Basic Testing & Verification

A few quick checks can be performed to verify the configuration:

 Using System Overview, verify that the VIP & RIP are shown as active (green)

 Using a browser, navigate to the VIP address, i.e. http://192.168.2.150 to verify that you can reach
the Real Servers via the Virtual Service using HTTP

 Using a browser, navigate to the STunnel SSL VIP address, i.e. https://192.168.2.150 to verify that
you can reach the Real Servers via the Virtual Service using HTTPS

 Check / verify the certificate details

Chapter 11 – Configuration Examples Page 221

Appliance Administration Manual v8.1 Loadbalancer.org

Chapter 12 – Testing Load Balanced Services

Chapter 12 – Testing Load Balanced Services Page 222

 Appliance Administration Manual v8.1 Loadbalancer.org

Testing Load Balanced Services

For example, to test a web server based configuration, add a page to each web servers root directory e.g.
test.html and put the server name on this page for easy identification during the tests.

Use two or more clients to do the testing. Open up a web browser on each test clients and enter the URL
for the VIP e.g. http://192.168.110.10

Each client should see a different server name because of the load balancing algorithm in use i.e. they are
being load balanced across the cluster.

Why test using two clients? If you use a single client it will most likely keep on hitting the same server for
multiple requests. This is to do with the way that the load balancing algorithms are optimized.

Diagnosing VIP Connection Problems

1. Make sure that the device is active - this can be checked in the WUI. For a single appliance, the
status bar should report Master & Active as shown below:

2. Check that the VIP/floating IP is up - Using View Configuration > Network Configuration verify that
the VIP is active on the load balancer, if not check Logs > Heartbeat for errors.

The above example shows that the interface address (192.168.110.85) and the VIP address
(192.168.110.90) are both up.

3. Check that the Real Servers are up - Using System Overview make sure that none of your VIPs are
colored red. If they are, the entire cluster is down (i.e. all Real Servers). Green indicates a healthy
cluster, yellow indicates that your cluster may need attention (one or more of the Real Servers may be
down), and blue indicates all Real Server have been deliberately taken offline (by using either Halt or
Drain).

4. Check the connection state -

Chapter 12 – Testing Load Balanced Services Page 223

 Appliance Administration Manual v8.1 Loadbalancer.org

For Layer 4 DR mode VIPs check Reports > Layer 4 Current Connections to view the current traffic in
detail. Any packets with state SYN_RECV imply that the 'ARP Problem' has not been correctly solved
on the Real Servers. See page 79 for more details on solving the ARP problem.

For layer 4 NAT mode VIPs check Reports > Layer 4 Current Connections to view the current traffic in
detail. Any packets with state SYN_RECV often imply that the default gateway on the Real Servers has
not been set to be an IP address on the load balancer.

For Layer 7 VIPs check Reports > Layer 7 Status. The default credentials required are:

username: loadbalancer
password: loadbalancer

This will open a second tab in the browser and display a statistics/status report as shown in the
example below:

Taking Real Servers Offline

1) Using the System Overview check that when you Halt one of the Real Servers the connections are
redirected to the other server in the cluster.

2) Remove the network cable from one of the web servers or stop the web service/process, wait a few
seconds (for the load balancer to detect the change) and then refresh the browsers on both clients. They
should now both switch to the same server (since one has been removed from the load balancing list).
Also check that the server is shown red (down) in the system overview.

3) Replace the network cable, wait a few seconds and then refresh the browsers again. After a few
refreshes they should again show different web servers. Also check that the server is shown green (up) in
the system overview.

The System Overview will also show the updated status as these tests are performed:

Chapter 12 – Testing Load Balanced Services Page 224

 Appliance Administration Manual v8.1 Loadbalancer.org

In this example:

'rip1 ' is green, this indicates that it's operating normally.

'rip2 ' is blue, this indicates that it has been either Halted or Drained. in this example Halt has been used as
indicated by Online (Halt) being displayed. If it had been drained it would show as Online (Drain).

'rip3' is red, this indicates that it has failed a health check.

NOTE : The System Overview supports sorting of VIPs. This can be done by clicking on the
column headings or by drag & drop. For more details please refer to page 178.

Using Log Files

The appliance includes several log files that are very useful when diagnosing issues. Please refer to the
next chapter for more details on the logs available.

Using Reports
The appliance includes several reports that are very useful when diagnosing issues. Please refer to the next
chapter for more details on the reports available.

NOTE : When testing a clustered pair, also make sure that failover to the slave appliance and
failback to the master appliance is working correctly. For more details please refer to page
192.

Chapter 12 – Testing Load Balanced Services Page 225

Appliance Administration Manual v8.1 Loadbalancer.org

Chapter 13 – Appliance Monitoring

Chapter 13 – Appliance Monitoring Page 226

 Appliance Administration Manual v8.1 Loadbalancer.org

Appliance Log Files

All appliance logs can be accessed using the Logs option in the WUI.

Load Balancer
File: /var/log/lbadmin.log
The lbadmin log shows all changes made to the appliances configuration. This is very useful for tracking
changes made to the configuration.

Layer 4
File: /var/log/ldirectord.log
The Ldirectord log shows the output from the health checking daemon. This is useful for checking the
health your Real Servers or pinning down any configuration errors. The logging here can be quite verbose
but it clearly shows exactly what the health checking process is doing.

Layer 7
File: /var/log/haproxy.log
If activated via Cluster Configuration > Layer 7 – Advanced Configuration, this will show the contents of
the HAProxy log. This is a very detailed log of all HAProxy transactions. It's also possible to configure
HAProxy to log errors only.

SSL Termination (Pound)

File: /var/log/poundssl.log
If activated via Cluster Configuration > SSL – Advanced Configuration, this will show the contents of the
Pound log. This is a very detailed log of all Pound SSL transactions.

SSL Termination (STunnel)

File: /var/log/stunnel.log
If activated via Edit Configuration > SSL – Advanced Configuration, this will show the contents of the
STunnel log. The required debug level can also be set.

Heartbeat
File: /var/log/ha.log
The heartbeat log shows the status of the heartbeat daemons. Heartbeat is used whether configured as a
single device or as a clustered pair. The log provides a detailed real-time status of heartbeat.

Apache Error Log

File: /var/log/httpd/error.log
Shows Apache errors. These can be generated by the WUI and WAF (Web Application Firewall).

Apache User Log

File: /var/log/httpd/user_access.log

Chapter 13 – Appliance Monitoring Page 227

 Appliance Administration Manual v8.1 Loadbalancer.org

Shows Apache user access logs. Can be generated by WUI and the WAF (Web Application Firewall) since
both utilize Apache for their operation.

WAF Logs
Various log file for monitoring WAFs.

Appliance Reports
All reports can be accessed using the Reports option in the WUI.

Layer 4 Status
This report shows the current weight and number of active & inactive connections for each Real Server. If a
Real Server has failed a health check, it will not be listed. Use the Logs > Layer 4 option to view the
Ldirectord log file if expected servers are not listed.

In the example above, the details for RIP3 are not displayed because it's failing its health checks.

Chapter 13 – Appliance Monitoring Page 228

 Appliance Administration Manual v8.1 Loadbalancer.org

Layer 4 Traffic Rate

This report shows the current connections per second and bytes per second to each Real Server. If a Real
Server has failed a health check, it will not be listed.

In the example above, the details for RIP3 are not displayed because it's failing its health checks.

Chapter 13 – Appliance Monitoring Page 229

 Appliance Administration Manual v8.1 Loadbalancer.org

Layer 4 traffic Counters

This report shows the volume of traffic to each Real Server since the counters were last re-set. If a Real
Server has failed a health check, it will not be listed.

N.B. These reports are generated in real time. Direct Routing is the default load balancing method and you
will not see any stats for return packets as shown above (as they do not pass through the load balancer).
They will be seen for NAT mode since return traffic does pass back via the load balancer.

In the example above, the details for RIP3 are not displayed because it's failing its health checks.

Chapter 13 – Appliance Monitoring Page 230

 Appliance Administration Manual v8.1 Loadbalancer.org

Layer 4 Current Connections

The current connections report is very useful for diagnosing issues with routing or ARP related problems.
In the example below, the state is shown as SYN_RECV. For layer 4 DR mode this is normally a good
indication that the ARP problem has not been solved. For NAT mode, this is a good indication that the Real
Servers default gateway has not been configured to be the load balancer and therefore return traffic is not
routed correctly.

N.B. The IPVS connection entries in state NONE represent the persistence related entries for client
connections, and are not actual client connections. These only appear when persistence is enabled.

Layer 4 Current Connections (resolve hostnames)

This is the same as the current connections report but is slower as it looks up the DNS name of each IP
address.

Layer 7 Status
This report is provided by the stats instance of HAProxy. This web page contains the current live status of
all of the configured layer 7 HAProxy virtual and Real Servers.

Log in using: Username: loadbalancer

Password: loadbalancer

N.B. This password can be changed using the 'statistics password' field available under Cluster
Configuration > Layer 7 – Advanced Configuration

Chapter 13 – Appliance Monitoring Page 231

 Appliance Administration Manual v8.1 Loadbalancer.org

Layer 7 Stick Table

Displays the layer 7 stick tables. For example, if a layer 7 VIP is created using RDP cookie persistence, a stick
table will be used. The related VIP is then available in the drop-down as shown below:

Notes:

 Stick tables are used when either source IP persistence or RDP cookie persistence is used with
layer 7 Virtual Services

 Individual stick table entries can be removed by clicking the red 'X' in the remove column, the
whole table can be cleared by clicking the Clear Table button

Graphing
Graphs are automatically configured when new Virtual and Real Servers are defined.

Graphs – Load Balanced Services

Graphs for the configured Virtual & Real Servers can be accessed either from the System Overview using
the appropriate blue colored graph icon that appears next to each VIP and RIP or from the drop-down
available in the WUI under Reports > Graphing.

Using the System Overview

The graph is displayed by clicking the relevant blue icon that's displayed next to each VIP / RIP:

When this method is used, the daily Service Connections Graph (i.e. the last 24 hrs) is displayed for the
particular VIP or RIP:

Chapter 13 – Appliance Monitoring Page 232

 Appliance Administration Manual v8.1 Loadbalancer.org

Clicking anywhere within this graph opens the complete list of graphs for the VIP / RIP in question. This is
the same as selecting the VIP/RIP in the Reports > Graphing menu options as explained below.

Using the WUI Option: Reports > Graphing

When selected, a drop-down similar to the following is displayed:

When selected in this way, a complete list of graphs is displayed for the VIP / RIP selected as shown below:

N.B. As VIPs & RIPs are added or removed, these are automatically added / removed from the drop-down
list

Chapter 13 – Appliance Monitoring Page 233

 Appliance Administration Manual v8.1 Loadbalancer.org

The following graphs are displayed for each VIP or RIP selected:

• 5 x Connection graphs : Hourly, daily, weekly, monthly and yearly

• 5 x Bytes/s graphs : Hourly, daily, weekly, monthly and yearly

Chapter 13 – Appliance Monitoring Page 234

 Appliance Administration Manual v8.1 Loadbalancer.org

Graphs – Appliance Specific

Appliance specific graphs are available for the following statistics:

• Network Throughout
• Load Average
• Memory Usage
• Disk Usage

The first three graphs listed above are displayed in the System Overview by default although these can be
disabled/hidden if preferred using the WUI option: Local Configuration > Graphing.
All four graphs can also be accessed using the WUI option: Reports > Graphing, then selecting the required
graph from the bottom of the list.

System Overview Graphs

Chapter 13 – Appliance Monitoring Page 235

 Appliance Administration Manual v8.1 Loadbalancer.org

As shown above, daily graphs for Network Bandwidth, System Load Average and Memory Usage are
displayed by default in the System Overview. Clicking anywhere within these graph opens the full list of
related graphs (hourly, daily, weekly etc.). This is the same as selecting the graph in the Reports menu as
explained below.

Using the Reports Menu

When selected, a drop-down including all VIPs / RIPs as well as the 4 appliance specific graphs is
displayed:

Graph Options
A number of graph options are available.

To change the settings:

 In the WUI, open Local Configuration > Graphing

Data collection for each graphing category can be enabled (default) by selecting On and clicking
Update
Data collection for each graphing category can be disabled by selecting Off and clicking Update
The stored data for each graphing category can be removed by selecting Delete and clicking Update

Chapter 13 – Appliance Monitoring Page 236

 Appliance Administration Manual v8.1 Loadbalancer.org

Advanced Configuration Settings

Interval - Set the data collector Interval time specified in seconds. Change the interval for which data is
recorded by the collector. This is a global value and will effect all collectors. Do not change unless advised
to do so by support.
WARNING – Changing this value will reset the RRD database files and you will loose all your previous
data!!

Timeout - Set the data collector timeout specified in seconds. Change the timeout for the data collector
when querying the various services. Do not change unless advised to do so by support.

Threads - Set the number of data collector process threads. Change the number of collector process
threads to use for reading stats. Do not change unless advised to do so by support.

Logging - Enable collector logging for collectd. Warning this is incredibly verbose and should only be
used for debugging purposes.

Chapter 13 – Appliance Monitoring Page 237

 Appliance Administration Manual v8.1 Loadbalancer.org

SNMP Reporting
By default, SNMP is disabled on the appliance. Once the SNMP settings are configured using the WUI
option: Local Configuration > SNMP Configuration , the SNMP service is set to auto start at boot.

SNMP for Layer 4 Based Services

The root OID for Layer 4 based services is: 1.3.6.1.4.1.8225.4711

You can test if everything works by running the command shown below:

[root@lbmaster ~]# snmpwalk -c public -v 2c -m LVS-MIB localhost 1.3.6.1.4.1.8225.4711

LVS-MIB::lvsVersion.0 = STRING: "1.2.0"

LVS-MIB::lvsNumServices.0 = INTEGER: 2
LVS-MIB::lvsHashTableSize.0 = INTEGER: 4096
LVS-MIB::lvsTcpTimeOut.0 = INTEGER: 900
LVS-MIB::lvsTcpFinTimeOut.0 = INTEGER: 120
LVS-MIB::lvsUdpTimeOut.0 = INTEGER: 300
LVS-MIB::lvsDaemonState.0 = INTEGER: none(0)
…
etc.

N.B. LVS-MIB.txt and other MIB files are available on the appliance in /usr/share/snmp/mibs/
You can also use all the usual MIB II counters and gauges such as network and CPU etc.

Monitoring Layer 4 VIPs & RIPs using SNMP

To list the Virtual Services use the command shown below:
[root@lbmaster ~]# snmpwalk -c public -v 2c -m LVS-MIB localhost 1.3.6.1.4.1.8225.4711.17.1.4

LVS-MIB::lvsServiceAddr.1 = IpAddress: 192.168.110.194

To list the Real Servers use the command shown below:

[root@lbmaster ~]# snmpwalk -c public -v 2c -m LVS-MIB localhost 1.3.6.1.4.1.8225.4711.18.1.3

LVS-MIB::lvsRealServerAddr.2.1 = IpAddress: 10.0.0.101

LVS-MIB::lvsRealServerAddr.2.2 = IpAddress: 10.0.0.100

This indicates that all servers are passing their health-check. If the check fails, that server will be omitted
from the list as shown below:
[root@lbmaster ~]# snmpwalk -c public -v 2c -m LVS-MIB localhost 1.3.6.1.4.1.8225.4711.18.1.3

LVS-MIB::lvsRealServerAddr.2.1 = IpAddress: 10.0.0.100

In this case, 10.0.0.101 is now failing its health-check so has been omitted from the list.

Chapter 13 – Appliance Monitoring Page 238

 Appliance Administration Manual v8.1 Loadbalancer.org

SNMP for Layer 7 Based Services

The root OID for Layer 7 front-end services is: 1.3.6.1.4.1.29385.106.1.0
The root OID for Layer 7 back-end services is: 1.3.6.1.4.1.29385.106.1.1

To list the Front End stats use the command shown below:

[root@lbmaster ~]# snmpwalk -c public -v 2c localhost 1.3.6.1.4.1.29385.106.1.0

SNMPv2-SMI::enterprises.29385.106.1.0.0.1.0 = STRING: "stats"

SNMPv2-SMI::enterprises.29385.106.1.0.1.1.0 = STRING: "FRONTEND"
SNMPv2-SMI::enterprises.29385.106.1.0.2.1.0 = ""
SNMPv2-SMI::enterprises.29385.106.1.0.3.1.0 = ""
SNMPv2-SMI::enterprises.29385.106.1.0.4.1.0 = STRING: "0"
SNMPv2-SMI::enterprises.29385.106.1.0.5.1.0 = STRING: "0"
SNMPv2-SMI::enterprises.29385.106.1.0.6.1.0 = STRING: "2000"
etc.

To list the Back End stats use the command shown below:

[root@lbmaster ~]# snmpwalk -c public -v 2c localhost 1.3.6.1.4.1.29385.106.1.1

SNMPv2-SMI::enterprises.29385.106.1.1.0.1.0 = STRING: "stats"

SNMPv2-SMI::enterprises.29385.106.1.1.1.1.0 = STRING: "BACKEND"
SNMPv2-SMI::enterprises.29385.106.1.1.2.1.0 = STRING: "0"
SNMPv2-SMI::enterprises.29385.106.1.1.3.1.0 = STRING: "0"
SNMPv2-SMI::enterprises.29385.106.1.1.4.1.0 = STRING: "0"
SNMPv2-SMI::enterprises.29385.106.1.1.5.1.0 = STRING: "0"
SNMPv2-SMI::enterprises.29385.106.1.1.6.1.0 = STRING: "2000"
SNMPv2-SMI::enterprises.29385.106.1.1.7.1.0 = STRING: "0"
SNMPv2-SMI::enterprises.29385.106.1.1.8.1.0 = STRING: "0"
etc.

Monitoring Layer 7 RIPs using SNMP

To list the Real Servers use the command shown below:

[root@lbmaster ~]# snmpwalk -c public -v 2c localhost 1.3.6.1.4.1.29385.106.1.2.1

SNMPv2-SMI::enterprises.29385.106.1.2.1.1.1 = STRING: "backup"

SNMPv2-SMI::enterprises.29385.106.1.2.1.1.2 = STRING: "IIS1"
SNMPv2-SMI::enterprises.29385.106.1.2.1.1.3 = STRING: "IIS2"
SNMPv2-SMI::enterprises.29385.106.1.2.1.2.1 = STRING: "backup"
SNMPv2-SMI::enterprises.29385.106.1.2.1.2.2 = STRING: "RDP1"
SNMPv2-SMI::enterprises.29385.106.1.2.1.2.3 = STRING: "RDP2"

Chapter 13 – Appliance Monitoring Page 239

 Appliance Administration Manual v8.1 Loadbalancer.org

To get the health status of each of these Real Servers use the command shown below:
[root@lbmaster ~]# snmpwalk -c public -v 2c localhost 1.3.6.1.4.1.29385.106.1.2.17

SNMPv2-SMI::enterprises.29385.106.1.2.17.1.1 = STRING: "no check"

SNMPv2-SMI::enterprises.29385.106.1.2.17.1.2 = STRING: "UP"
SNMPv2-SMI::enterprises.29385.106.1.2.17.1.3 = STRING: "DOWN"
SNMPv2-SMI::enterprises.29385.106.1.2.17.2.1 = STRING: "no check"
SNMPv2-SMI::enterprises.29385.106.1.2.17.2.2 = STRING: "DOWN"
SNMPv2-SMI::enterprises.29385.106.1.2.17.2.3 = STRING: "DOWN"

In this example, IIS1 is passing its health-check and IIS2, RDP1 & RDP2 are failing their health-checks.

NOTE : Please refer to page 54 for details on configuring SNMP settings such as community
string etc.

Page 240
Appliance Administration Manual v8.1 Loadbalancer.org

Chapter 14 – Useful Tools & Utilities

Chapter 14 – Useful Tools & Utilities Page 241

 Appliance Administration Manual v8.1 Loadbalancer.org

Useful Diagnostics Tools

Full root access to the appliance is supported which enables many useful commands to be run directly at
the console or via an SSH session. Many commands can also be run using the WUI option: Local
Configuration > Execute Shell Command. Several commonly used examples are listed below.

Netstat
Print network connections, routing tables, interface statistics, masquerade connections, and multicast
memberships. Useful to check that services are listening on the correct IP / port.

e.g. netstat -anp

Command Output:

Active Internet connections (servers and established)

Proto Recv-Q Send-Q Local Address Foreign Address State PID/Program name

tcp 0 0 0.0.0.0:7777 0.0.0.0:* LISTEN 19216/haproxy

tcp 0 0 127.0.0.1:7778 0.0.0.0:* LISTEN 19216/haproxy
tcp 0 0 127.0.0.1:199 0.0.0.0:* LISTEN 19938/snmpd
tcp 0 0 0.0.0.0:22 0.0.0.0:* LISTEN 1466/sshd
tcp 0 0 0.0.0.0:9081 0.0.0.0:* LISTEN 16114/nginx
tcp 0 0 :::9443 :::* LISTEN 1627/httpd
tcp 0 0 2001:470:1f09:d72::146:80 :::* LISTEN 19216/haproxy
tcp 0 0 :::22 :::* LISTEN 1466/sshd
tcp 0 0 :::9080 :::* LISTEN 1627/httpd

Telnet
The telnet command is used to communicate with another host using the TELNET protocol. Useful for
testing that a connection to a specific port can be made. Note that this command should be run from the
console or a terminal session rather than via the WUI.

e.g. telnet 192.168.100.10 80

In this example, 192.168.100.10 is a Real Server, the command is useful to ensure that the load balancer is
able to successfully connect to this server on port 80.

[root@lbmaster ~]# telnet 192.168.100.10 80

Trying 192.168.100.10...
Connected to 192.168.100.10.
Escape character is '^]'.

Chapter 14 – Useful Tools & Utilities Page 242

 Appliance Administration Manual v8.1 Loadbalancer.org

Tcpdump
Tcpdump enables network traffic to be dumped to a file for analysis. Filters can also be applied if required
to select which traffic is captured. Very useful tool when diagnosing network issues. Note that this
command should be run from the console or a terminal session rather than via the WUI.
e.g. tcpdump -i any -s 0 -w tcpdump-file.pcap
This command captures all network traffic on all interfaces using the maximum packet size of 65535 bytes
and dumps it to a file called tcpdump-file.pcap. To end the capture use CTRL+C.
Our support department may ask you to run this command and send the resulting output file to help them
diagnose certain network issues.

Ethtool
Ethtool is used for querying settings of an Ethernet device and changing them.

e.g. ethtool eth0

Output:

Settings for eth0:

Supported ports: [ TP ]
Supported link modes: 10baseT/Half 10baseT/Full
100baseT/Half 100baseT/Full
1000baseT/Full
Supports auto-negotiation: Yes
Advertised link modes: 10baseT/Half 10baseT/Full
100baseT/Half 100baseT/Full
1000baseT/Full
Advertised pause frame use: No
Advertised auto-negotiation: Yes
Speed: 100Mb/s
Duplex: Full
Port: Twisted Pair
PHYAD: 1
Transceiver: internal
Auto-negotiation: on
MDI-X: off
Supports Wake-on: pumbag
Wake-on: g
Current message level: 0x00000001 (1)
drv
Link detected: yes

Chapter 14 – Useful Tools & Utilities Page 243

 Appliance Administration Manual v8.1 Loadbalancer.org

Wireshark
Wireshark is an open source application that can be used to analyze tcpdump output files. It can be
downloaded from the following location:

http://www.wireshark.org/download.html

Windows Specific Tools

WinSCP
WinSCP is an open source application that allows files to be uploaded/downloaded to/from the load
balancer using Windows. It can be downloaded from the following location:

http://winscp.net/eng/download.php

PuTTy
PuTTy is an open source SSH client for Windows. It can be downloaded from the following location:

http://www.chiark.greenend.org.uk/~sgtatham/putty/download.html

Chapter 14 – Useful Tools & Utilities Page 244

 Appliance Administration Manual v8.1 Loadbalancer.org

Remote Support Tools

The Loadbalancer.org Support Department uses Teamviewer for remote desktop support. The client-side
software is available at the following links:

Windows clients: http://downloads.loadbalancer.org/support/quicksupport/WindowsQS.exe

Mac clients: http://downloads.loadbalancer.org/support/quicksupport/MacQS.zip
Linux clients: http://downloads.loadbalancer.org/support/quicksupport/LinuxQS.tar.gz

Once downloaded, the client should be installed on a local machine that has access to the load balancer's
WUI and also to the load balancer via SSH (Putty, WinSCP for Windows). Our Support Engineers will
provide guidance as required.

NOTE : The download links mentioned above can also be accessed using the WUI option:
Support > Useful Links

Chapter 14 – Useful Tools & Utilities Page 245

Appliance Administration Manual v8.1 Loadbalancer.org

Chapter 15 – Backup & Restore and Disaster Recovery

Chapter 15 – Backup & Restore and Disaster Page 246

Recovery
 Appliance Administration Manual v8.1 Loadbalancer.org

Introduction
The appliance uses various configuration files to store all settings. Files that must be backed up to enable a
full restore are as follows:

XML configuration file – The is the main file for the appliance. All configuration details including local
settings and load balanced services settings are stored here. This file can be backed up using the WUI.

Firewall Script – If manual changes such as manual firewall marks have been made, this file is also
important. This file can be backed up using the WUI.

SSL Certificate PEM files – If SSL is terminated on the appliance, these files are also important. These files
can be backed up using the WUI.

Backup & Restore

The WUI can be used for to perform backup and restore functions. To access these options:

 In the WUI, open Maintenance > Backup & Restore

Backup Options

Download XML configuration file – download and save the load balancer's XML configuration file
Download Firewall script – download and save load balancer's firewall script
Download SSL Certificates – download and save the load balancer's SSL certificates
Download HAProxy manual configuration – download and save the load balancer's layer 7 manual
configuration file
Make local XML backup – creates a local backup of the current XML file in
/etc/loadbalancer.org/userbkup
Make local Firewall Script backup – creates a local backup of the current rc.firewall in
/etc/loadbalancer.org/userbkup

Chapter 15 – Backup & Restore and Disaster Page 247

Recovery
 Appliance Administration Manual v8.1 Loadbalancer.org

Restore Options
Upload XML file and Restore – upload an XML file and restore load balancer settings
Restore from the last local XML backup – Restore the last local backup created with the 'Make local XML
Backup' option
Restore Manufacturer's defaults – Restore system settings to default values

N.B. The xml restore feature is not backward compatible with previous major versions of the software, e.g.
it's not possible to restore a V7.6.4 xml file to a v7.5 appliance.

Synchronization Options
Synchronize Configuration with peer – replicate the load balanced services configuration to the slave
device.

NOTE : For details of which settings are NOT replicated from master to slave when using this
option, please refer to page 182.

Restoring XML Files

The screen shot below shows an ongoing restore from a local XML file backup:

Once complete, you'll need to either restart or reload heartbeat to complete the restore process as
explained in the yellow message box:

Chapter 15 – Backup & Restore and Disaster Page 248

Recovery
 Appliance Administration Manual v8.1 Loadbalancer.org

Disaster Recovery
Being Prepared
To be able to quickly recover your appliance when a disaster occurs it's important that you create a backup
of the XML file as well as other relevant configuration files and keep them stored in a secure location off
the load balancer. Ideally you should keep a backup of both the master and slave configurations. This can
easily be done by following the steps below:

Backing Up SSH System Files

The following SSH related files must be backed up from both the master and slave devices to ensure that
an HA pair can be recovered without disrupting running services. Under Windows, WinSCP can be used -
Please refer to page 244 for more details.

/root/.ssh/authorized_keys2
/root/.ssh/id_rsa
/root/.ssh/id_rsa.pub
/etc/ssh/ssh_host_rsa_key
/etc/ssh/ssh_host_rsa_key.pub
/etc/ssh/ssh_known_hosts

IMPORTANT! - these files should be kept in a secure location

Backing Up Configuration Files to a Remote Location

Login to the Web User Interface:

Username : loadbalancer
Password : loadbalancer

Backup the XML configuration file:

• Select Maintenance > Backup & Restore and click Download XML configuration file
• Select an appropriate location to store the file
• Update the filename if required then save the file

If manual firewall marks have been configured or any other manual firewall script changes have been
made, backup the firewall configuration:
• Select Maintenance > Backup & Restore and click Download Firewall Script
• Select an appropriate location to store the file
• Update the filename if required then save the file

If you're terminating SSL on the load balancer, backup your certificates as well:
• Select Maintenance > Backup & Restore and click Download SSL Certificates
• Select an appropriate location to store the file
• Update the filename if required then save the file

If you have manual layer 7 services, back these up too:

• Select Maintenance > Backup & Restore and click Download Haproxy manual configuration
• Select an appropriate location to store the file
• Update the filename if required then save the file

Chapter 15 – Backup & Restore and Disaster Page 249

Recovery
 Appliance Administration Manual v8.1 Loadbalancer.org

Using wget to Copy the Files

It's also possible to use wget from a remote Linux host to pull the XML configuration file and firewall script
from the appliance:
wget --user=loadbalancer --password=loadbalancer http://<IP >:9080/lbadmin/config/getxmlconfig.php
-O lb_config.xml

wget --user=loadbalancer --password=loadbalancer http://<IP>:9080/lbadmin/config/getfirewall.php -O

rc.firewall

N.B. Replace the password 'loadbalancer' with your password if it's been changed.

Backing up locally on the Load Balancer

To create local backups of the various configuration files, follow these steps:

Log in to the web interface:

Username : loadbalancer
Password : loadbalancer

• Select Maintenance > Backup & Restore and click Make local XML backup
• Select Maintenance > Backup & Restore > and click Make local Firewall Script backup

A copy of these files will be stored in /etc/loadbalancer.org/userbkup

Appliance Recovery using a USB Memory Stick

NOTE : This will only work on 64Bit hardware. From v6.x onwards, all appliances are 64Bit. If
you're running an older version, this may or may not be possible depending on the hardware.

Checking older hardware for Compatibility

If you are running v5.x and wish to determine whether your appliance is 64Bit and can be upgraded to the
latest version, use the following command:

grep flags /proc/cpuinfo

This can be run from the WUI using Local Configuration > Execute Shell command, at the console or via a
terminal session.

If lm (long mode) is present in the output then the CPU is 64Bit and you can proceed. If not then your
appliance is 32Bit and you are limited to the latest v5 software.

The latest images require a standard disk (Dell hardware) or a high speed IDE DOM / SATA SSD (Supermicro
hardware) of at least 4GB in size. If you're already running v6.x or later then you will already have this and
should be able to simply re-image your current drive, disk module or SSD.

If you're upgrading from v5.x you may need to upgrade the storage device and possibly the hardware.

Chapter 15 – Backup & Restore and Disaster Page 250

Recovery
 Appliance Administration Manual v8.1 Loadbalancer.org

Obtaining the latest disk image

The latest disk image can be downloaded from our website – please contact [email protected]
for more details.

Extracting the image from the compressed archive

Extract the image using tar under Linux or something like WinRar or 7-Zip under Windows (not the built-in
Windows extractor).

Preparing the USB stick

Under Linux:

after formatting the USB stick run the command:

dd if=/imagefilename.img of=/dev/nameofusbdisk

e.g.

dd if=/tmp/v7.5.0_r3368.img of=/dev/sda

Do not use /dev/sdax where 'x' is a number, for example – /dev/sda1 as this will install to a partition on
your usb stick. Use the whole disk /dev/sda Instead.

NOTE: Be careful using this command – make sure you specify the correct disk !!

Under Windows:

For Windows, a third party image writer must be used. Several free ones are available, the example below
uses Win32 Disk Imager which can be downloaded here:

http://sourceforge.net/projects/win32diskimager/

First extract the archive, then run the executable

Chapter 15 – Backup & Restore and Disaster Page 251

Recovery
 Appliance Administration Manual v8.1 Loadbalancer.org

Select the image file and set the appropriate output Device as shown above

Click Write

NOTE: Be careful using this utility – make sure you specify the correct disk !!

Using the USB Stick to restore the Appliance

• Change the appliance's BIOS settings to boot from USB first (on some models the stick must be
plugged in to allow it to be selected as a boot device)

• Boot the appliance, after the initial boot messages the following prompt will appear:
DO YOU WISH TO CONTINUE?
Please enter yes or no

• Type yes and press <Enter>

• The installation will take around 2-3 minutes, once complete the following message will be
displayed:
Installation Finished

• As directed, press any key to shutdown the load balancer

• Once shutdown, remove the USB stick

• Power up the appliance

• Login at the console:

Username : root
Password : loadbalancer

• Run the following command:

lbrestore <Enter>

• Reboot the appliance once again

• Set the required IP address using the network setup wizard as described on page 35.

NOTE : You'll need to reapply your license key file to ensure the newly restored appliance is
correctly licensed. Please contact [email protected] if you have any issues.

Chapter 15 – Backup & Restore and Disaster Page 252

Recovery
 Appliance Administration Manual v8.1 Loadbalancer.org

Disaster Recovery After Slave Failure

If the slave unit has failed, the master will continue to provide load balancing services as normal. However
it's important to recover the slave unit as soon as possible to restore the HA pair.

Recovery Steps

NOTE : This procedure ensures that the HA pair is re-established without disrupting currently
running services. The is achieved by restoring all relevant files to the new/re-imaged slave
device, then reloading heartbeat rather than restarting.

• If the failed slave is still on, power it down

• For a hardware appliance:

◦ Disconnect all cables

◦ If the SSD / HD has failed and has been replaced and needs to be re-imaged, follow the steps
on page 250 to restore the appliance firmware

• Power up the new/re-imaged appliance

• Login to the console as:

username: setup
password: setup

now run through the network setup wizard to configure the initial network settings

• On the new/re-imaged slave appliance open the WUI option: Maintenance > Backup & Restore,
select the restore tab, browse to the XML backup that was taken from the original slave unit, then
click Upload

• On the new/re-imaged slave appliance restore the following SSH related files that were backed up
from the original slave unit:

▪ /root/.ssh/authorized_keys2
▪ /root/.ssh/id_rsa
▪ /root/.ssh/id_rsa.pub
▪ /etc/ssh/ssh_host_rsa_key
▪ /etc/ssh/ssh_host_rsa_key.pub
▪ /etc/ssh/ssh_known_hosts

N.B. restoring these files ensure that the remaining master can successfully communicate with
the new slave device via SSH. If this was not done, the pair would need to be broken and re-
established which will cause running services to be interrupted

• On the new/re-imaged slave appliance open the WUI option: Maintenance > Restart Services, then
click Reload Heartbeat

Chapter 15 – Backup & Restore and Disaster Page 253

Recovery
 Appliance Administration Manual v8.1 Loadbalancer.org

Verify the HA Configuration

Once the HA pair has been reconfigured:

• Verify that the master displays: Master | Active | Link

• Verify that the slave displays: Slave | Passive | Link

NOTE : For more details on verifying the HA pair please refer to page 189.

Creating a Slave XML File from the Running Master

If a backup copy from the slave is not available, It's also possible to use the XML file from the master
instead. If there is no current backup of this, then use the WUI option: Maintenance > Backup & Restore >
Download XML Configuration file to create the file. A couple of changes then need to be made so the file
represents the slave unit rather than the master as detailed below.

Steps (with example IP addresses) to modify a copy of the masters XML file for use on the slave:

find & Change:

<physical>
<network>
<role>master</role>
<hostname>lbmaster</hostname>
<master>192.168.67.22</master>
<slave>192.168.67.23</slave>

To:

<physical>
<network>
<role>slave</role> (i.e. change the role to slave)
<hostname>lbslave</hostname> (i.e. change the hostname to lbslave)
<master>192.168.67.22</master>
<slave>192.168.67.23</slave>

Find & Change:

<rip>
<eth0>192.168.67.22/24</eth0>
<eth1></eth1>
</rip>

To:

<rip>
<eth0>192.168.67.23/24</eth0> (i.e. change to the slaves IP address)
<eth1></eth1>
</rip>

Chapter 15 – Backup & Restore and Disaster Page 254

Recovery
 Appliance Administration Manual v8.1 Loadbalancer.org

Disaster Recovery After Master Failure

If the master unit has failed, the slave will take over and provide load balancing services. However it's
important to recover the master unit as soon as possible to restore the HA pair.

Recovery Steps

NOTE : This procedure ensures that the HA pair is re-established without disrupting currently
running services. The is achieved by restoring all relevant files to the new/re-imaged master
device, then reloading heartbeat rather than restarting.

• If the failed master is still on, power it down

• For a hardware appliance:

◦ Disconnect all cables

◦ If the SSD / HD has failed and has been replaced and needs to be re-imaged, follow the steps
on page 250 to restore the appliance firmware

• Power up the new/re-imaged appliance

• Login to the console as:

username: setup
password: setup

now run through the network setup wizard to configure the initial network settings

• On the new/re-imaged master appliance open the WUI option: Maintenance > Backup & Restore,
select the restore tab, browse to the XML backup that was taken from the original master unit, then
click Upload

• On the new/re-imaged master appliance restore the following SSH files that were backed up from
the original master unit:

▪ /root/.ssh/authorized_keys2
▪ /root/.ssh/id_rsa
▪ /root/.ssh/id_rsa.pub
▪ /etc/ssh/ssh_host_rsa_key
▪ /etc/ssh/ssh_host_rsa_key.pub
▪ /etc/ssh/ssh_known_hosts

N.B. restoring these files ensures that the remaining slave can successfully communicate with
the new master device via SSH. If this was not done, the pair would need to be broken and re-
established which will cause running services to be interrupted

• On the new/re-imaged master appliance open the WUI option: Maintenance > Restart Services,
then click Reload Heartbeat

Chapter 15 – Backup & Restore and Disaster Page 255

Recovery
 Appliance Administration Manual v8.1 Loadbalancer.org

Verify the HA Configuration

Once the HA pair has been reconfigured:

• Verify that the master displays: Master | Passive | Link

• Verify that the slave displays: Slave | Active | Link

NOTE : For more details on verifying the HA pair please refer to page 189.

Creating a Master XML File from the Running Slave

If a backup copy from the master is not available, It's also possible to use the XML file from the slave
instead. If there is no current backup of this, then use the WUI option: Maintenance > Backup & Restore >
Download XML Configuration file to create the file. A couple of changes then need to be made so the file
represents the master unit rather than the slave as detailed below.

Steps (with example IP addresses) to modify a copy of the masters XML file for use on the slave:

find & Change:

<physical>
<network>
<role>slave</role>
<hostname>lbslave</hostname>
<master>192.168.67.22</master>
<slave>192.168.67.23</slave>

To:

<physical>
<network>
<role>master</role> (i.e. change the role to master)
<hostname>lbmaster</hostname> (i.e. change the hostname to lbmaster)
<master>192.168.67.22</master>
<slave>192.168.67.23</slave>

Find & Change:

<rip>
<eth0>192.168.67.23/24</eth0>
<eth1></eth1>
</rip>

To:

<rip>
<eth0>192.168.67.22/24</eth0> (i.e. change to the masters IP address)
<eth1></eth1>
</rip>

Chapter 15 – Backup & Restore and Disaster Page 256

Recovery
Appliance Administration Manual v8.1 Loadbalancer.org

Chapter 16 – Technical Support

Chapter 16 – Technical Support Page 257

 Appliance Administration Manual v8.1 Loadbalancer.org

Introduction
Loadbalancer.org have a team of very experienced support Engineers who are available to assist with your
load balancer deployment.

Unlimited support is available as follows:

 During the cover period of any active support agreement

(to purchase a support package, please contact: [email protected])

 During the 30 day Virtual Appliance trial period

(to download the trial please go to: http://www.loadbalancer.org//resources/free-trial)

WUI Support Options

Contact Us
This option provides details on how to contact Loadbalancer.org, how to report any issues and what
information we'll need to resolve issues as quickly as we can. As mentioned here, the Loadbalancer.org
support team can be contacted using the email address: [email protected]
Sending an email to this address creates a ticket in our help desk system and enables all technical support
staff to view the case. This is the most efficient way to contact support and guarantees that any reported
issues will be acted upon and addressed as quickly and efficiently as possible.

Chapter 16 – Technical Support Page 258

 Appliance Administration Manual v8.1 Loadbalancer.org

Technical Support Download

This option enables the Support Download to be created. The download is a compressed archive
containing all log files and configuration files from the appliance and should be attached to your email.

To generate the archive, click the Generate Archive button.

Once complete, a link will be available to download the archive:

Once downloaded, attach the file to your email when contacting support, or if the file is large, it can be
posted to our upload server – please ask our support staff about this option.

Chapter 16 – Technical Support Page 259

 Appliance Administration Manual v8.1 Loadbalancer.org

Useful Links
This option presents a number of self explanatory web links.

Chapter 16 – Technical Support Page 260

Appliance Administration Manual v8.1 Loadbalancer.org

Appendix

Appendix Page 261

 Appliance Administration Manual v8.1 Loadbalancer.org

Front & Rear Panel Layouts

Enterprise R20 & Enterprise Max

Eth2 Eth3

Eth0 Eth1

Enterprise 10G & Enterprise R320

Eth2 Eth3

Eth0 Eth1

Appendix Page 262

 Appliance Administration Manual v8.1 Loadbalancer.org

IPMI (Remote Management) Configuration for the Enterprise R20 & MAX
The Enterprise R20 and Enterprise MAX includes an IPMI module to allow remote control & management.
This can either be accessed via the dedicated IPMI Ethernet interface or via one of the standard Ethernet
interfaces in bridged mode.
To use the dedicated IPMI interface, ensure that a network cable is plugged into the interface before
powering up the appliance.

Configuring the IP Address

By default the IP address is set using DHCP. The address allocated is displayed in the IPMI sub-menu in
system setup. If preferred, a static IP address can also be set using the same menu. To access system setup,
hit <DEL> as directed at boot time.

IPMI BIOS Menu:

Appendix Page 263

 Appliance Administration Manual v8.1 Loadbalancer.org

To set the address

change Update IPMI LAN configuration to 'Yes'

change Configuration Address Source to 'Static'
now set the IP address, mask etc. as required.

IPMI BIOS Menu:

Appendix Page 264

 Appliance Administration Manual v8.1 Loadbalancer.org

To set the address

select Set LAN Configuration

change IP Address Source to 'Static'
now set the IP address, mask etc. as required.

Accessing the login page

Using a browser, connect to http://<ip address>

the following login prompt is displayed:

username: ADMIN
default password: ADMIN

Once logged in, the following screen is displayed:

Appendix Page 265

 Appliance Administration Manual v8.1 Loadbalancer.org

IPMI Interface
As mentioned above IPMI can be accessed via the dedicated interface or via one of the standard on-board
NICs. This can be configured in the IPMI interface using: Configuration > Network > LAN Interface

Dedicate – use the dedicated interface only

Share – run in bridge mode using one of the standard NICs
Failover – allows either connection method to be used (the default)

Remote Control
To access the systems console, simple click on the Remote Console Preview image. A new window will
open with access to the console of the appliance.

N.B. You cannot SSH into the module directly. You need to connect via the IPMI's web interface, then use
the remote control option as mentioned above. This can also be accessed using the 'Remote Control'
option in the top menu. From here you can use the Launch Console option to launch a virtual Java
console which will allow you to use the device as if you stood in front of the device. Next the 'Power
Control' options menu will give you several options such as Restart Server, Power off and Power Cycle
server. these options will perform the same function as pressing the physical reset button on the unit
(Reset Server) as well as being able to perform the same functions as the physical power switch as well.
Please do remember that the IPMI power control options are completely independent of the Loadbalancer
software and that the reset option is the same as pressing reset on your PC.

Appendix Page 266

 Appliance Administration Manual v8.1 Loadbalancer.org

iDRAC (Remote Management) Configuration for the Enterprise 10G & R320
iDRAC enables remote management of the Enterprise 10G and Enterprise R320 appliances. The following
models include iDRAC by default:

Default IP Address
By default the following static IP address & mask is assigned to the iDRAC interface:

IP address: 192.168.0.120
Mask: 255.255.255.0

This can be changed using the iDRAC management interface accessible at boot-up.

Default Username & Password

The default username & password is:

username: root
password: calvin

Appendix Page 267

 Appliance Administration Manual v8.1 Loadbalancer.org

Appliance IPv4 Address Format (CIDR notation)

When specifying IP addresses on the appliance, CIDR format is used. The following table shows the various
masks and the corresponding IPv4 IP/CIDR equivalents:

Mask IP/CIDR

255.255.255.255 a.b.c.d/32
255.255.255.254 a.b.c.d/31
255.255.255.252 a.b.c.d/30
255.255.255.248 a.b.c.d/29
255.255.255.240 a.b.c.d/28
255.255.255.224 a.b.c.d/27
255.255.255.192 a.b.c.d/26
255.255.255.128 a.b.c.d/25
255.255.255.000 a.b.c.d/24
255.255.254.000 a.b.c.d/23
255.255.252.000 a.b.c.d/22
255.255.248.000 a.b.c.d/21
255.255.240.000 a.b.c.d/20
255.255.224.000 a.b.c.d/19
255.255.192.000 a.b.c.d/18
255.255.128.000 a.b.c.d/17
255.255.000.000 a.b.c.d/16
255.254.000.000 a.b.c.d/15
255.252.000.000 a.b.c.d/14
255.248.000.000 a.b.c.d/13
255.240.000.000 a.b.c.d/12
255.224.000.000 a.b.c.d/11
255.192.000.000 a.b.c.d/10
255.128.000.000 a.b.c.d/9
255.000.000.000 a.b.c.d/8
254.000.000.000 a.b.c.d/7
252.000.000.000 a.b.c.d/6
248.000.000.000 a.b.c.d/5
240.000.000.000 a.b.c.d/4
224.000.000.000 a.b.c.d/3
192.000.000.000 a.b.c.d/2
128.000.000.000 a.b.c.d/1

Appendix Page 268

Appliance Administration Manual v8.1 Loadbalancer.org

Company Contact Information

Website URL : www.loadbalancer.org

North America (US) Loadbalancer.org, Inc.

4250 Lancaster Pike, Suite 120
Wilmington
DE 19805
USA
Tel : +1 888.867.9504
Fax : +1 302.213.0122
Email (sales) : [email protected]
Email (support) : [email protected]

North America (Canada) Loadbalancer.org Ltd

300-422 Richards Street
Vancouver, BC
V6B 2Z4
Canada
Tel : +1 866.998.0508
Fax : +1 302.213.0122
Email (sales) : [email protected]
Email (support) : [email protected]

Europe (UK) Loadbalancer.org Ltd.

Compass House
North Harbour Business Park
Portsmouth, PO6 4PS
UK
Tel : +44 (0)330 3801064
Fax : +44 (0)870 4327672
Email (sales) : [email protected]
Email (support) : [email protected]

Europe (Germany) Loadbalancer.org GmbH

Alt Pempelfort 2
40211 Düsseldorf
Germany
Tel : +49 (0)211 9793 7203
Fax : +49 (0)30 920 383 6495
Email (sales) : [email protected]
Email (support) : [email protected]

Appendix Page 269