Using Position Manager BiSS-C Library On

IDDK Hardware

User's Guide

Literature Number: SPRUI36

November 2015
 Contents

1 Introduction to IDDK ............................................................................................................. 4

2 Hardware Configuration ........................................................................................................ 4
3 Hardware Overview .............................................................................................................. 6
3.1 Functional Blocks ........................................................................................................ 6
3.2 Processor Section (Control Processor Slot – H1) ................................................................... 7
3.3 Position Encoder Suite .................................................................................................. 8
3.4 Power Supply ............................................................................................................. 9
4 Hardware Resource Mapping ............................................................................................... 10
4.1 Digital Signal Mapping ................................................................................................. 10
4.2 Jumpers and Switches ................................................................................................. 10
4.3 Headers and Connectors .............................................................................................. 10
5 Hardware Setup Instructions for PM_bissc Library Evaluation ................................................. 11
6 Software Setup for PM BiSS-C Evaluation Example Projects ................................................... 12
6.1 Installing Code Composer and controlSUITE ....................................................................... 12
6.2 Software Flow Diagram ................................................................................................ 12
6.3 Setup Code Composer Studio to Work With TMDXIDDK379D .................................................. 13
6.4 Configuring a Project ................................................................................................... 14
6.5 Build and Load the Project ............................................................................................ 15
6.6 Setup Watch Window and Graphs ................................................................................... 17
6.7 Run the Code ........................................................................................................... 18
7 References ........................................................................................................................ 18

2 Table of Contents SPRUI36 – November 2015

Submit Documentation Feedback
Copyright © 2015, Texas Instruments Incorporated
www.ti.com

List of Figures
1 IDDK EVM Kit ................................................................................................................ 6
2 Layout of IDDK EVM With its Functional Macros........................................................................ 7
3 Processor Block .............................................................................................................. 7
4 Position Sensor Suite ....................................................................................................... 8
5 EnDat/BiSS Interface Header .............................................................................................. 8
6 Power Supply Block ......................................................................................................... 9
7 M12 Cable, Female End .................................................................................................. 11
8 Software Flow Diagram for the Example Project PM_bissc_SystemTest .......................................... 12
9 Configuring a New Target ................................................................................................. 13
10 Adding PM_bissc Example Project to Workspace ..................................................................... 14
11 Selecting the F2837x_RAM Configuration .............................................................................. 15
12 Selecting the CPUs to Connect .......................................................................................... 16
13 Configuring the Expressions Window.................................................................................... 17

List of Tables
1 Hardware Macros in IDDK Used for PM_bissc Evaluation ............................................................. 6
2 Digital Signal Mapping on Control Card H1............................................................................. 10
3 Purpose of Jumpers and Switches ....................................................................................... 10
4 Headers and Connectors .................................................................................................. 10

SPRUI36 – November 2015 List of Figures 3

Submit Documentation Feedback
Copyright © 2015, Texas Instruments Incorporated
 User's Guide
SPRUI36 – November 2015

Using Position Manager BiSS-C Library On IDDK

Hardware

1 Introduction to IDDK
The DesignDRIVE Kit (IDDK) is a single platform that makes it easy to develop and evaluate design
solutions for many industrial drive and servo topologies. The IDDK offers support for a wide variety of
motor types, sensing technologies, encoder standards, and communications networks, as well as easy
expansion to develop with real-time Ethernet communications and functional safety topologies to enable
more comprehensive, integrated system solutions. Based on the real-time control architecture of TI’s
C2000™ microcontrollers (MCUs), the kit is ideal for the development of industrial inverter and servo
drives used in robotics, computer numerical control machinery (CNC), elevators, materials conveyance,
and other industrial manufacturing applications.
The IDDK offers an integrated drive design with a full-power stage to drive a three-phase motor, easing
evaluation of a diverse range of feedback sensing and control topologies. The kit includes a 180-pin
HSEC controlCARD based on the TMS320F28379D C2000 Delfino™ MCU, which integrates dual C28x
real-time processing cores and dual CLA real-time coprocessors, providing 800 MIPS of floating-point
performance with integrated trigonometric and FFT acceleration.
The sophisticated sensing peripherals on the TMS320F28379D MCU, including sigma-delta filter modules
with up to eight input channels, four high-performance 16-bit ADCs, and eight windowed comparators,
enable the IDDK to support shunt, flux gate/ HALL, and sigma-delta current sensing simultaneously. For
position feedback, the IDDK leverages integrated MCU support for resolver and incremental encoder
interfaces. In addition, customers can also explore configuration options that allow the MCU to be placed
on either side of the high voltage isolation barrier.
The kit is designed to plug into 110-V/220-V AC mains, delivers up to 8 Amps, and is rated to drive motors
up to one horsepower.
This document covers the kit contents and hardware details, and explains the functions and locations of
various connectors present on the board. This document supersedes all documents available for the kit.
For more details, see the DesignDRIVE Development Kit IDDK Hardware Reference Guide (SPRUI23).

2 Hardware Configuration
To experiment with the IDDK for Position Manager BiSS-C Library evaluation, the following components
are needed:
• An IDDK EVM
• TMDXCNCD28379D
• USB-B to A cable
• Encoder and connectors NOT included in the kit that are required for evaluation:
– BiSS-C Encoder (for example, Kuebler 8.F5863.1426.C423)
– Cable (for the above Kuebler encoder, a 8-pole M12 cable – length as needed by the application
(max 100m))

C2000, Delfino, Code Composer Studio, controlSUITE are trademarks of Texas Instruments.
All other trademarks are the property of their respective owners.

4 Using Position Manager BiSS-C Library On IDDK Hardware SPRUI36 – November 2015
Submit Documentation Feedback
Copyright © 2015, Texas Instruments Incorporated
www.ti.com Hardware Configuration

– Adapter to connect cable to IDDK (for the above Kuebler encoder, a circular 8 position female to
wire leads – M12 receptacle)

– An external isolated 15-V power supply needed for MCU code development (preferably with a
barrel connector commonly referred to as DC jack). Power supply EMSA150120-P5P-SZ is used
for testing.
– PC with Code Composer Studio™ (CCSv6 or greater) installed
• DesignDRIVE Development Kit IDDK Hardware Reference Guide (SPRUI23), located at
controlSUITE\development_kits\TMDSIDDK_v2.0\~Docs\
For the schematic details of the IDDK EVM, see the file located at
controlSUITE\development_kits\TMDSIDDK_v2.0\IDDK_HwDevPkg\IDDK_HwDevPkg_v2.2.1.

SPRUI36 – November 2015 Using Position Manager BiSS-C Library On IDDK Hardware 5
Submit Documentation Feedback
Copyright © 2015, Texas Instruments Incorporated
Hardware Overview www.ti.com

Figure 1. IDDK EVM Kit

3 Hardware Overview
This section describes the subset of the components required for the Position Manager PM_bissc Library
evaluation only. Complete hardware overview of the kit can be obtained from the DesignDRIVE
Development Kit IDDK Hardware Reference Guide (SPRUI23), available on controlSUITE™.
Evaluation of the Position Manager PM_bissc Library requires usage of:
• Processor (CPU) block for control
• Position encoder suite
• On-board power supplies

3.1 Functional Blocks

Table 1 shows the subset of functional blocks on DesignDRIVE Development Kit IDDK Hardware, along
with the macro names, used for Position Manager PM_bissc Library evaluation.

Table 1. Hardware Macros in IDDK Used for PM_bissc Evaluation

Functional Block Macro Reference Macro Function
DC Power Supply – Linear Reg 15 V to 5
Power Supplies M9
V / 3.3 V
Position Encoder Suite M12 Biss Encoder Interface
Processor/controlCARD H1 All other functions

6 Using Position Manager BiSS-C Library On IDDK Hardware SPRUI36 – November 2015
Submit Documentation Feedback
Copyright © 2015, Texas Instruments Incorporated
www.ti.com Hardware Overview

Each functional block, and the macros that make them, are presented in brief detail in the sections below.
The layout of various macros in the board is given in Figure 2. Schematic details of the individual macros
are available at
controlSUITE\development_kits\TMDSIDDK_v2.0\IDDK_HwDevPkg\IDDK_HwDevPkg_v2.2.1.

Figure 2. Layout of IDDK EVM With its Functional Macros

3.2 Processor Section (Control Processor Slot – H1)

Figure 3. Processor Block

The IDDK is designed around the main control processor card in slot H1. This is designed to plug in a
c2000 Delfino (TMS320F28379D) MCU control card TMDXCNCD28379D designed with a HSEC180pin
edge connector.

SPRUI36 – November 2015 Using Position Manager BiSS-C Library On IDDK Hardware 7
Submit Documentation Feedback
Copyright © 2015, Texas Instruments Incorporated
Hardware Overview www.ti.com

3.3 Position Encoder Suite

Figure 4. Position Sensor Suite

This block provides a range of position encoder and sensing interfaces, such as:
• QEP
• Resolver
• Sin-Cos
• EnDat / BiSS
PM BiSS-C Library evaluation uses this interface for communication.

3.3.1 BiSS Encoder

This is designed as a macro, referred to as M12. This is a common interface for BiSS/EnDat encoders. H6
is the external interface header and it interfaces digital signals only, as shown in Figure 5. GPIO32 is used
to control on/off of 5-V supply details in Table 2.
H6

DATA – 8 7 NC

DATA + 6 5 +15 V

CLK – 4 3 NC

CLK + 2 1 GND

Figure 5. EnDat/BiSS Interface Header

8 Using Position Manager BiSS-C Library On IDDK Hardware SPRUI36 – November 2015
Submit Documentation Feedback
Copyright © 2015, Texas Instruments Incorporated
www.ti.com Hardware Overview

3.4 Power Supply

An external power supply is preferred to power the controller during code development so that the board
operates in low voltage. This ensures a safe environment, as there is no high-voltage node present on the
board.
The kit only needs 15 V of power, which can be received through M9 or M3. When the controller
processor is to be on the cold-side, M9 should be used, which is what will be assumed below.
M9 has a power supply jack ([M9]-JP1) and a toggle switch ([M9]-SW1). An external (15-V) power supply
can be fed in through [M9]-JP1, while [M9]-SW1 should be turned away from the Int position when power
is needed.
Settings needed to run when the controller processor is on the cold-side:
1. [Main]-J6, J7, and J8 should be jumpered
2. [Main]-J2 should NOT be jumpered
3. [Main]-R9, R11, R13 should be populated
4. [Main]-R8, R10, R12 should NOT be populated
5. Ground resistors on the secondary side of the board should be configured for the controller to be on
the cold-side. For more details, see the DesignDRIVE Development Kit IDDK - Hardware Reference
Guide (SPRUI23) and the DesignDRIVE Development Kit IDDK - User’s Guide (SPRUI24).
Other options, such as running the PM_bissc project from a controller located on the hot-side, are possible
with different settings. For more details, see the DesignDRIVE Development Kit IDDK - Hardware
Reference Guide (SPRUI23) and the DesignDRIVE Development Kit IDDK - User’s Guide (SPRUI24).

Figure 6. Power Supply Block

SPRUI36 – November 2015 Using Position Manager BiSS-C Library On IDDK Hardware 9
Submit Documentation Feedback
Copyright © 2015, Texas Instruments Incorporated
Hardware Resource Mapping www.ti.com

4 Hardware Resource Mapping

The sections below show the hardware resource requirements and signal mapping for PM_bissc Library
evaluation on IDDK.

4.1 Digital Signal Mapping

Table 2 shows the functional mapping of signals, connected to the control processor on H1, that are
relevant to PM_bissc Library evaluation.

Table 2. Digital Signal Mapping on Control Card H1

MCU Peripheral associated
IDDK Signal Name MCU GPIO Function
with GPIO
En-Clk 6 ABS ENC-CLK Absolute Encoder Clock out
C1-SPIB-CLK 7 PM CLK Encoder SPI Clock out
En-DO 24 SPIB SPI I/f for Abs Encoder
En-DI 25 SPIB SPI I/f for Abs Encoder
C1-SPIB-CLK 26 SPIB SPI I/f for Abs Encoder
C1-SPIB-STE 27 SPIB SPI I/f for Abs Encoder
En-PwrEn 32 GPIO output Power Enable for Abs Encoder
En-TxEn 34 PM TX En Tx Enable for Abs Encoder

4.2 Jumpers and Switches

Table 3 lists the jumpers that must be populated for PM_bissc Library evaluation.

Table 3. Purpose of Jumpers and Switches

Jumpers / Switches Configuration Description
[Main] - J6- J8 Populate Jumpers to bring out linear regulator block M9 voltages
[Main] - J10 Populate Connects GPIO to BiSS/EnDat Clock
[Main] - J12 Don’t Populate
[Main] - J13 Populate Connect SPISTE to ground
[Main] - J14-17 Don’t Populate
[Main] - J18 Populate (1-2) Connects Encoder data out (En-Do-1 to the processor)
[Main] - J19-21 GND headers for probe access
Selects 15-V supply from JP1 or onboard from M8 to generate
[M9] - SW1 Turn ON
5 V and 3.3 V

4.3 Headers and Connectors

Table 4 shows the headers and connectors available on board.

Table 4. Headers and Connectors

Headers and Connectors Description
[M9] – JP1 15-V DC power supply jack adapter
[Main] - H1 180-pin HSEC connector slot for control processor card
[Main] – H6 4×2 header for EnDat/BiSS

10 Using Position Manager BiSS-C Library On IDDK Hardware SPRUI36 – November 2015
Submit Documentation Feedback
Copyright © 2015, Texas Instruments Incorporated
www.ti.com Hardware Setup Instructions for PM_bissc Library Evaluation

5 Hardware Setup Instructions for PM_bissc Library Evaluation

1. Ensure default configuration. Jumpers [Main]-J6, [Main]-J7 and [Main]-J8 must be in front of macro M9
and resistors [Main]-R9, R11, R13 must be populated. GND plane resistors R14 and R15 must be
mounted as shown in figures Various GND Planes on the Bottom of Board and Default Connection of
Various GND Planes of the Power Supplies and GND Plane Configurations section of the
DesignDRIVE Development Kit IDDK - Hardware Reference Guide (SPRUI23).
2. Unpack the TMDXCNCD28379D control card and slide it down in the connector slot of [Main]-H1.
Using even pressure on both ends of the card, push down vertically until it cannot slide down further.
(To remove the card, spread open the retaining clips, if present, and pull the card out applying even
force at the far edges).
3. Connect a USB cable to connector J1 on the control card. The control card isolates the JTAG signals
between the C2000 device and the computer. LED D2 on the control card should light.
4. Connect to the encoder:
(a) Prepare an adapter cable to connect the encoder cable to the IDDK BiSS interface ([Main] – H6
4×2 header) using Circular 8 position female to wire leads – M12 receptacle.

For more information, see the encoder and cable specifications and hardware schematics in
Section 3.3.
(b) Cable connections between the Encoder and IDDK: insert the header created using the adapter
cable above into the [Main] – H6 4×2 header of IDDK. The other end of the adapter connects to the
male side of the M12 cable. The female end of the M12 cable connects to the encoder as shown in
Figure 7.

Figure 7. M12 Cable, Female End

SPRUI36 – November 2015 Using Position Manager BiSS-C Library On IDDK Hardware 11
Submit Documentation Feedback
Copyright © 2015, Texas Instruments Incorporated
Software Setup for PM BiSS-C Evaluation Example Projects www.ti.com

5. Ensure that the toggle switch [M9]-SW1 is in Int position. Connect an isolated 15-V DC power supply
to [M9]-JP1.
6. Turn on the toggle switch [M9]-SW1. Now, [M9]-LD1 should turn on. More LEDs on the control card
should light up, indicating that the control card is receiving power from the board.

6 Software Setup for PM BiSS-C Evaluation Example Projects

6.1 Installing Code Composer and controlSUITE

1. If not already installed, install Code Composer v6.x or later from http://www.ti.com/tool/CCSTUDIO.
2. Go to http://www.ti.com/controlsuite and run the controlSUITE installer. Allow the installer to download
and update any automatically checked software for C2000.
3. EnDat22 Library is available at:
<base> install directory is C:\ti\controlSUITE\libs\app_libs\position_manager\vX.X
The following sub-directory structure is used:
<base>\Doc – Documentation
<base>\Float – Contains implementation of the library and corresponding include file.
<base>\examples – Examples using the BiSS-C library

6.2 Software Flow Diagram

The software flow used in Example Project PM_bissc_SystemTest is depicted in Figure 8.

Figure 8. Software Flow Diagram for the Example Project PM_bissc_SystemTest

12 Using Position Manager BiSS-C Library On IDDK Hardware SPRUI36 – November 2015
Submit Documentation Feedback
Copyright © 2015, Texas Instruments Incorporated
www.ti.com Software Setup for PM BiSS-C Evaluation Example Projects

6.3 Setup Code Composer Studio to Work With TMDXIDDK379D

1. Open Code Composer Studio (CCSv6 or greater).
2. Once Code Composer Studio opens, the workspace launcher appears and asks to select a workspace
location. Workspace is a location on the hard drive containing all the user settings for the IDE, such as
which projects are open, what configuration is selected, and so forth. This can be anywhere on the
disk, the location mentioned below is just for reference. If this is not the first time running Code
Composer, the dialog below may not appear.
(a) Click the “Browse…” button
(b) Create the path C:\c2000 projects\CCSv6_workspaces\PM_BiSS-C_eval_workspace by making
new folders, as necessary
(c) Uncheck the box that says “Use this as the default and do not ask again”.
(d) Click OK
3. This opens a Getting Started tab with links to various tasks including creating a new project, importing
an existing project, or watching a tutorial on CCS. Click the Import Project Icon to skip the procedure to
step 2 in Section 6.4. Or, close the Getting Started tab and go to the next step.
4. Configure Code Composer to know which MCU it will be connecting to by setting up the Target
Configuration. This is already set up and configured in xds100v2_F2837x.ccxml, which is provided as
part of the files in the project; the user can skip to step 1 in Section 6.4. However, for general
information regarding setting up this configuration file, use steps 6, 7, and 8 in this list.
5. Set a new configuration file by clicking View → Target Configuration. This opens the Target
Configuration window. In this window, click on . Give a name to the new configuration file,
depending on the target device. If the Use Shared Location checkbox is checked, this configuration file
can be stored in a common location by CCS for use by other projects as well. Click Finish.
6. This opens up a new tab as shown in Figure 9. Select and enter the options as shown:
• Connection – Texas Instruments XDS100v2 USB Emulator (or) Texas Instruments XDS100v2 USB
Debug Probe
• Device – the C2000 MCU on the control card, such as the TMS320F28379D
Click Save and close.

Figure 9. Configuring a New Target

7. Click View → Target Configurations. In the User Defined section, find the file that was created in steps
6 and 7 in this list. Right-click on this file and select Set as Default. To use the configuration file
supplied with the project, click View → Target Configurations. Then, Expand Projects →
PM_bissc_SystemTest, right-click on the xds100v2_F2837x.ccxml file and choose Set as Default. This
tab also allows you to reuse existing target configurations and link them to specific projects.

SPRUI36 – November 2015 Using Position Manager BiSS-C Library On IDDK Hardware 13
Submit Documentation Feedback
Copyright © 2015, Texas Instruments Incorporated
Software Setup for PM BiSS-C Evaluation Example Projects www.ti.com

8. Add the PM BiSS-C evaluation example project into the current workspace by clicking Project →
Import CCS Project. Select the project by browsing to:
C:\ti\controlSUITE\libs\app_libs\position_manager\v1_00_00_00\BiSS-C\examples\
PM_bissc_SystemTest. If there are multiple projects in this directory, click and choose the projects to
import and then click Finish. This copies all the selected projects into the workspace and shows only
one project; select it and click Finish.

Figure 10. Adding PM_bissc Example Project to Workspace

6.4 Configuring a Project

1. Assuming this is the first time using Code Composer, the xds100v2-F2837x should have been set as
the default target configuration. Verify this by viewing the xds100v2-f2837x.ccxml file in the expanded
project structure and a [Active/Default] status written next to it. By going to View → Target
Configurations, the user can edit existing target configurations or change the default or active
configuration. The user can also link a target configuration to a project in the workspace by right-
clicking on the Target Configuration name and selecting Link to Project.
2. The project can be configured to create code and run in either flash or RAM. Select either of the two;
however, for lab experiments use RAM configuration most of the time and move to the FLASH
configuration for production. As shown in Figure 11, right-click on an individual project and select
Active Build Configuration → CPU1_RAM configuration.

14 Using Position Manager BiSS-C Library On IDDK Hardware SPRUI36 – November 2015
Submit Documentation Feedback
Copyright © 2015, Texas Instruments Incorporated
www.ti.com Software Setup for PM BiSS-C Evaluation Example Projects

Figure 11. Selecting the F2837x_RAM Configuration

6.5 Build and Load the Project

1. Open the bissc.h file, ensure BISSC_FREQ_DIVIDER is set as needed, and save this file. For more
details, see the C2000 Position Manager BISS-C Library User's Guide (SPRUI37)
(C:\ti\controlSUITE\libs\app_libs\position_manager\v1_00_00_00\BiSS-C\Doc\PM_bissc_Lib.pdf).
2. Right-click on the project name, click on Rebuild Project and watch the console window. Any errors in
the project are displayed in the Console window.

3. On a successful completion of the build, click the Debug button, located in the top-left side of the
screen. If it is the first time using CCS, the following window may pop up requesting the user to
connect to one of the two CPUs in F28379x. Click on the box next to CPU1.

SPRUI36 – November 2015 Using Position Manager BiSS-C Library On IDDK Hardware 15
Submit Documentation Feedback
Copyright © 2015, Texas Instruments Incorporated
Software Setup for PM BiSS-C Evaluation Example Projects www.ti.com

Figure 12. Selecting the CPUs to Connect

4. Now, the IDE automatically connects to the target, loads the output file into the device, and changes to
the Debug perspective.
5. Click Tools → Debugger Options → Program/Memory Load Options. The user can enable the
debugger to reset the processor each time it reloads the program by checking Reset the target on
program load or restart and clicking Remember My Settings to make this setting permanent.

6. Click on the Enable silicon real-time mode button , which also auto-selects the Enable polite real-
time mode button . This allows the user to edit and view variables in real time. Do not reset the
CPU without disabling these real-time options.
7. A message box may appear. If so, select YES to enable debug events. This sets bit 1 (DGBM bit) of
Status Register 1 (ST1) to a 0. DGBM is the debug enable mask bit. When the DGBM bit is set to 0,
memory and register values can be passed to the host processor for updating the debugger windows.

16 Using Position Manager BiSS-C Library On IDDK Hardware SPRUI36 – November 2015
Submit Documentation Feedback
Copyright © 2015, Texas Instruments Incorporated
www.ti.com Software Setup for PM BiSS-C Evaluation Example Projects

6.6 Setup Watch Window and Graphs

1. Click View → Expressions on the menu bar to open a watch window to view the variables used in the
project. Add variables to the watch window, as shown in Figure 13. It uses the number format
associated with variables during declaration. Select the desired number format for the variable by right-
clicking and choosing it. Figure 13 shows a typical expressions window.

Figure 13. Configuring the Expressions Window

Alternately, a group of variables can be imported into the Expressions window; right click in the
Expressions Window and select Import. Then, browse to the .txt file containing these variables. Browse
to the root directory of the project and pick PM_bissc_SystemTest_VAR.txt, then click OK to import the
variables.
2. Click on the Continuous Refresh button in the watch window. This enables the window to run with
real-time mode. By clicking the down arrow in this watch window, the user can select Customize
Continuous Refresh Interval and edit the refresh rate of the watch window. Note that choosing an
interval that is too fast can affect performance.

SPRUI36 – November 2015 Using Position Manager BiSS-C Library On IDDK Hardware 17
Submit Documentation Feedback
Copyright © 2015, Texas Instruments Incorporated
Software Setup for PM BiSS-C Evaluation Example Projects www.ti.com

6.7 Run the Code

1. Run the code by pressing the Run Button in the Debug tab.
2. The project should now run and the values in the watch window should continuously update.
3. Once complete, reset the processor (Run → Reset → CPU Reset), then terminate the debug
session by clicking (Run → Terminate). This halts the program and disconnects Code Composer
from the MCU.
4. As the encoder sends the position information, observe the same in the watch window as the
biss_data_struct.position variable. The variable biss_data_struct.position reflects the latest position
received by the encoder.
5. If the encoder is not mounted on a spinning motor, the user can manually rotate the encoder shaft and
observe the position changing in the watch window.
6. It is not necessary to terminate the debug session each time the user changes or runs the code.
Instead, use the following procedure. After rebuilding the project, (Run → Reset → CPU Reset) ,
(Run → Restart ) , and enable real-time options. Once complete, disable real-time options and reset
the CPU. Terminate the project if the target device or the configuration is changed (RAM to Flash or
Flash to RAM) and prior to shutting down CCS.
7. Customize the project to meet your encoder and application requirements. Change the encoder type in
bissc.h. Users can also change the BiSS-C Clock frequency as instructed in the C2000 Position
Manager BISS-C Library User's Guide (SPRUI37).
8. Modify the example code as needed, and perform tests with different cable lengths.

7 References
• DesignDRIVE Development Kit IDDK Hardware Reference Guide (SPRUI23)
• DesignDRIVE Development Kit IDDK - User’s Guide (SPRUI24)
• C2000 Position Manager BISS-C Library User's Guide (SPRUI37)

18 Using Position Manager BiSS-C Library On IDDK Hardware SPRUI36 – November 2015
Submit Documentation Feedback
Copyright © 2015, Texas Instruments Incorporated
 IMPORTANT NOTICE

Texas Instruments Incorporated and its subsidiaries (TI) reserve the right to make corrections, enhancements, improvements and other
changes to its semiconductor products and services per JESD46, latest issue, and to discontinue any product or service per JESD48, latest
issue. Buyers should obtain the latest relevant information before placing orders and should verify that such information is current and
complete. All semiconductor products (also referred to herein as “components”) are sold subject to TI’s terms and conditions of sale
supplied at the time of order acknowledgment.
TI warrants performance of its components to the specifications applicable at the time of sale, in accordance with the warranty in TI’s terms
and conditions of sale of semiconductor products. Testing and other quality control techniques are used to the extent TI deems necessary
to support this warranty. Except where mandated by applicable law, testing of all parameters of each component is not necessarily
performed.
TI assumes no liability for applications assistance or the design of Buyers’ products. Buyers are responsible for their products and
applications using TI components. To minimize the risks associated with Buyers’ products and applications, Buyers should provide
adequate design and operating safeguards.
TI does not warrant or represent that any license, either express or implied, is granted under any patent right, copyright, mask work right, or
other intellectual property right relating to any combination, machine, or process in which TI components or services are used. Information
published by TI regarding third-party products or services does not constitute a license to use such products or services or a warranty or
endorsement thereof. Use of such information may require a license from a third party under the patents or other intellectual property of the
third party, or a license from TI under the patents or other intellectual property of TI.
Reproduction of significant portions of TI information in TI data books or data sheets is permissible only if reproduction is without alteration
and is accompanied by all associated warranties, conditions, limitations, and notices. TI is not responsible or liable for such altered
documentation. Information of third parties may be subject to additional restrictions.
Resale of TI components or services with statements different from or beyond the parameters stated by TI for that component or service
voids all express and any implied warranties for the associated TI component or service and is an unfair and deceptive business practice.
TI is not responsible or liable for any such statements.
Buyer acknowledges and agrees that it is solely responsible for compliance with all legal, regulatory and safety-related requirements
concerning its products, and any use of TI components in its applications, notwithstanding any applications-related information or support
that may be provided by TI. Buyer represents and agrees that it has all the necessary expertise to create and implement safeguards which
anticipate dangerous consequences of failures, monitor failures and their consequences, lessen the likelihood of failures that might cause
harm and take appropriate remedial actions. Buyer will fully indemnify TI and its representatives against any damages arising out of the use
of any TI components in safety-critical applications.
In some cases, TI components may be promoted specifically to facilitate safety-related applications. With such components, TI’s goal is to
help enable customers to design and create their own end-product solutions that meet applicable functional safety standards and
requirements. Nonetheless, such components are subject to these terms.
No TI components are authorized for use in FDA Class III (or similar life-critical medical equipment) unless authorized officers of the parties
have executed a special agreement specifically governing such use.
Only those TI components which TI has specifically designated as military grade or “enhanced plastic” are designed and intended for use in
military/aerospace applications or environments. Buyer acknowledges and agrees that any military or aerospace use of TI components
which have not been so designated is solely at the Buyer's risk, and that Buyer is solely responsible for compliance with all legal and
regulatory requirements in connection with such use.
TI has specifically designated certain components as meeting ISO/TS16949 requirements, mainly for automotive use. In any case of use of
non-designated products, TI will not be responsible for any failure to meet ISO/TS16949.

Products Applications
Audio www.ti.com/audio Automotive and Transportation www.ti.com/automotive
Amplifiers amplifier.ti.com Communications and Telecom www.ti.com/communications
Data Converters dataconverter.ti.com Computers and Peripherals www.ti.com/computers
DLP® Products www.dlp.com Consumer Electronics www.ti.com/consumer-apps
DSP dsp.ti.com Energy and Lighting www.ti.com/energy
Clocks and Timers www.ti.com/clocks Industrial www.ti.com/industrial
Interface interface.ti.com Medical www.ti.com/medical
Logic logic.ti.com Security www.ti.com/security
Power Mgmt power.ti.com Space, Avionics and Defense www.ti.com/space-avionics-defense
Microcontrollers microcontroller.ti.com Video and Imaging www.ti.com/video
RFID www.ti-rfid.com
OMAP Applications Processors www.ti.com/omap TI E2E Community e2e.ti.com
Wireless Connectivity www.ti.com/wirelessconnectivity

Mailing Address: Texas Instruments, Post Office Box 655303, Dallas, Texas 75265
Copyright © 2015, Texas Instruments Incorporated