Nuclear Power Corporation of India Limited

(A Govt. of India Enterprise)

Tarapur Atomic Power Station - Tarapur Maharashtra Site.
CENTRALISED TENDERING CELL
Bill of Quantities / Financial Schedule (PART-II,Section-I)
Name Of Work : Construction of On-Site Emergency Support Centre for Tarapur
Atomic Power Station 1 to 4 at Tarapur Maharashtra Site.

Tender No. : TMS/CTC/CIVIL-3&4/2020/2273

NAME OF THE CONTRACTOR

Amount in
Sl. No. Description of item Unit Quantity Rate in Rs.
Rs.

SCHEDULE-A Earthwork, dewatering, conformatory

sub-soil investigations and construction works.
Earthwork excavation
1 Earth work excavation by mechanical means (Hydraulic
excavator) / manual means in foundation, in all types of
soil other than soft and hard rock, including backfilled
soil mixed with disintegrated rocks , dressing the sides
of foundation, ramming of bottom of foundations etc.
including shoring and dewatering (if necessary) and refilling
around foundations and plinth with selected excavated earth Cu.M 8,235
in layers of not more than 500 mm thick, each layer well
rammed and consolidated including disposing the surplus
earth within a distance of 200 m all as per specifications
including clearing jungle uprooting of vegetation grass etc
complete and as directed by the Engineer-in-charge upto
1.5m from EGL.

1.1 Extra over initial for depth 1.5m to 3m Cu.M 2,270

1.2 Extra over initial for depth 3m to 4.5m Cu.M 1,530
1.3 Extra over initial for depth 4.5m to 6m
Cu.M 880
1.4 Extra over initial depth from 6.00 m to 7.50 m
Cu.M 300
1.5 Extra over initial depth from 7.50 m to 9.00 m
Cu.M 100
1.6 Extra over initial depth from 9.00 m to 10.50 m
Cu.M 50
1.7 Lead charges for lead exceeding 1st 1 KM but not
exceeding 2km , by mechanical transport of Soil including
loading unloading, stacking / levelling etc. complete as per Cu.M 12,854
specifications and as directed by the Engineer in charge.

2 Earth work excavation by mechanical means (Hydraulic

excavator) / manual means in foundation, in Soft Rock
including shoring, dewatering if necessary, dressing the
sides of foundation, ramming the bottom of foundation,
refilling the sides of foundation, plinth, etc. with available
excavated earth in layers of not exceeding 500 mm in Cu.M 1,000
depth, each layer well rammed and consolidated disposal of
surplus excavated material within a lead of 200 m complete
as per specifications and as directed by the Engineer-in-
charge upto 1.5m from EGL.

2.1 Extra over initial for depth 4.5m to 6m

Cu.M 100

2.2 Extra over initial depth from 6.00 m to 7.50 m

Cu.M 400

2.3 Extra over initial depth from 7.50 m to 9.00 m

Cu.M 400
2.4 Extra over initial depth from 9.00 m to 10.50 m
Cu.M 100

BOQ of T. No. 2273 Page 1 of 18

 Amount in
Sl. No. Description of item Unit Quantity Rate in Rs.
Rs.

3 Earth work excavation in foundation in Hard Rock by

Chiselling and/or by mechanical means (Hydraulic
excavator) / Manual means including dewatering if
necessary, dressing the sides of foundation, ramming the
bottom of foundation, and stacking and / or disposing within
a distance of 200 m and filling the sides of foundation with
Cu.M 8,250
available selected excavated earth in layers not exceeding
500mm in depth, each layer well rammed and consolidated
etc complete as per specifications and as directed by the
Engineer-in-Charge upto 1.5m from EGL.

3.1 Extra over initial for depth 4.5m to 6m

Cu.M 116

3.2 Extra over initial depth from 6.00 m to 7.50 m

Cu.M 3,486

3.3 Extra over initial depth from 7.50 m to 9.00 m

Cu.M 3,486

3.4 Extra over initial depth from 9.00 m to 10.50 m

Cu.M 1,162
3.5 Lead charges for lead exceeding 1st 1 KM but not
exceeding 2km , by mechanical transport of Rock including
loading unloading, stacking / levelling etc. complete as per Cu.M 500
specifications and as directed by the Engineer in charge.

4 Labour charges for murum filling under floors of specified

thick in layers of not exceeding 150 mm thickness including
consolidation etc. complete (using murrum available at site.) Cu.M 15,000

4.1 Extra for compaction of earth work in embankment

under optimum moisture conditions to give at least 95% of
Cu.M 15,000
the maximum dry density (Proctor density)

5 PCC and brickwork

5.1 Providing and laying in position cement concrete of M-

15 grade (1:2:4, 1 cement, 2 crush sand, 4 graded stone
aggregate of maximum size 20 mm) including
consolidation, finishing curing, dewatering of surrounding Cu.M 850
water etc. complete as per specifications and drawings but
excluding the cost of Form work shuttering, centering and
steel reinforcement at all levels.

5.2 Providing and constructing brick work in cement

mortar (1 brick thick) using standard brick of approved
quality /class, make brand in superstructure above plinth
upto floor 2 level in all shapes and sizes including curing, Cu.M 115
rackingof joints complete as per specification and as
directed by EIC. brickworks in superstructre with standard
bricks in C.M. 1:4 using crushed Sand

6 Reinforced Cement concrete (RCC) of grade M-35

6.1 Providing and laying in position Reinforced Cement

concrete (RCC) of grade M-35 (Temperature during
placing shall not be more than 29 deg. celcius) using
20mm maximum size aggregates and crushed sand of
approved quality including Admixturesof approved Brand
and quality (Plasticiser or super plasticiser) if required,
including dewatering of surrounding water, weigh batching,
Mechanical mixing, transporting , placing, vibrating,
consolidation, finishing, curing, etc. complete but excluding
Cu.M 10,500
the cost of centering, shuttering and reinforcement complete
as per specifications up to Plinth Level (Cement Concrete
M-35 Grade nominal size 20 mm metal)
(Note:- batching plant of minimum 30 cu.m. per hour
capacity has to be installed at plant site and required
clearence has to be obtained by contractor from the
concerned authorities)

6.2 Extra for RCC all grades in superstructures upto 20m

height from Plinth level Cu.M 5,200

BOQ of T. No. 2273 Page 2 of 18

 Amount in
Sl. No. Description of item Unit Quantity Rate in Rs.
Rs.

6.3 Extra for RCC all grades above 20.00 metre height up to
and including 32.00 metre height from Plinth level. Cu.M 50

7 Providing Reinforcement steel for reinforced cement

concrete at all levels including supplying, preparation of
BBS, cutting, bending transporting, fixing ,Tieing in position
with PVC coated GI Binding wire all labour charges, cost of
cover blocks in specified grades of concrete etc complete
as per specification and drawing.

7.1 Using TMT Bars of Specified Grades of all sizes. TMT bars
to be supplied by the contractor from the own plants of
SAIL,RINL or TATA make only using virgin materials. MT 2,190

8 Providing , centering ,shuttering Form work using PVC

Film faced plywood to get a neat form finish surface for
all types of structures including necessary strutting, proping,
staging, supports etc and deshuttering the same after the
specified time all as per drawings and specifications and as
directed by the Engineer-in-charge at all levels.

8.1 for sub structure (Below Plinth level)

Sq.M 9,500

8.2 for superstructure (Above Plinth level)

Sq.M 18,000

8.3 Left -in shuttering: design, supply, place formwork for left-
in shuttering, using metal deck sheets as formwork inclusive
of all materials, labour, studs, fastners, tools and plants, two
coats of approved primer or bottom surface, retrievable
supporting materials etc. complete as per specification,
drawings and as directed by the Engineer. The non- Sqm 6
retrievable structural steel required to be provided for
supporting the left-in shutter shall be measured and paid in
relevant structural steel item.

Flooring

9 Supplying, Stacking and Laying of 230 mm Thick

Soling stones under Floor base including packing with
smaller stone and compacting with Hand roller / Floor
compactor including spreading and consolidation of blinding Sq.m 1,300
material, moorum etc. complete all as per specifications and
as directed by the Engineer-in-charge

10 Providing and fixing Glazed VITRIFIED floor/wall tiles of

approved make in different sizes conforming to IS : 15622 in
all colours and shades in Glossy or Matt or satin finish laid
ovber a bed of minimum 20 mm thick bed of cement mortar
1:4 (using Crushed sand) and jointing with grey cement
slurry including grouting with the joints with white cement
based Tile grout of approved make and matching shade
complete as per patterns, drawings and specifications
complete as directed by the Engineer in charge.

10.1 Using Tiles of size 600 X 600 mm

Sq.M 2,200
11 Providing and fixing 1st quality ceramic glazed floor
tiles of minimum 300 - 600 mm long and 300 - 600 mm
wide of 1st quality confirming to IS 15622 of approved
make in all colours and shades of any size as approved by
Engineer-in-charge over a bed of 20 mm thick bed of
cement mortar 1:4 (using 100% manufactured sand) and Sq.M 750
jointing with grey cement slurry @ 3.3 kg / sq.m including
pointing with white cement based Tile grout of ROFF /
BALENDURA of matching shade complete as per patterns,
drawings and specifications complete as directed by the
Engineer-in-charge.

BOQ of T. No. 2273 Page 3 of 18

 Amount in
Sl. No. Description of item Unit Quantity Rate in Rs.
Rs.

12 Providing and Fixing 2.00 mm thick Anti-Static PVC

sheet / tile in flooring and skirting( ELECTRA of
Responsive Industries ) in approved pattern on a smooth
and damp proof base using rubber based adhesive of
approved quality and manufatrer like Dunlop-S -758, Fevicol
SR 998 of equivalent including levelling small undulations
Sq.M 170
with plasterof paris if required, Copper foil strips as per
manufacturers specifications, rolling with light wooden roller
weighing about 5 kg all complete as directed by Engineer-in-
Charge in approved colour and shade PVC Anti static
Flooring -as per specifications.

Alumunium work, structural glazing and false ceiling]

13 Providing and fixing anodized aluminium work

(minimum anodizing thickness of 15 micron) for doors,
windows, Louvers / ventilators and partitions with
extruded built up standard tubular sections / Z sections and
other sections of approved make conforming to IS 733 and
IS 1285 fixed with rawl plugs and screws or with fixing clips
or with expansion hold fastners including necessary filling
up of gaps at junctions, at top, bottom and sides with
required PVC / neoprene gasket etc. Aluminium sections
shall be smooth, rust free, straight, mitred and jointed
mechanically wherever required including cleat angle, Kg. 675
aluminium snap beading for glazing /panelling, CP brass /
stainless screws all complete as per drawings and direction
of Engineer-in-charge including providing and fixing hinges /
pivots and making provision for fixing of fittings wherever
required including the cost of PVC / neoprene gasket
required filling the gaps using silicon grout sealant etc.
(fittings glazing and panelling if any, shall be paid for
separately)

Waterproofing

14 Providing cement based water proofing treatment to the

new terraces, chajjas, cleaning the concrete surfaces,
giving injections to the top slab as required with cement and
approved waterproofing compound solution to fill up all
inherent holes, voids, honeycombs etc. in the concrete slab,
setting brickbat coba in waterproof mortar with necessary
gradient for easy flow of water and continue the treatment
along the inner faces of parapet or other adhoining wall up
to a height of 300 mm in thew shap of vattas, with
waterproof plaster finished smooth with trovel in cement /
geru with false marking of 300 mm squares complete as
directed by the Engineer-in-chage.
Note:
The quoted rate shall include maintaining effectiveness of
water proofing system and roof insulation supplied for up to
defect liability period from the date of acceptance of these
systems by NPCIL.

14.1 With average thickness of 120 mm and minimum thickness

at khurra as 65 mm using crushed sand/river sand.
Sq.M. 1,300

15 Establishing leak tightness by water fill test by carrying

out test as per IS: 3370 (Part-1) for the reservoirs/
sumps/tanks of the following liquid retaining structures as
per approved drawing, specifications and as directed by the
Engineer. Payment will be made only after successful
completion of test and acceptance to NPCIL.
Note: Lumpsum 1
Necessary repair works for defective concrete and re-test,
as required, shall be carried out by the contractor at his
own cost using the approved method, materials and
technical specifications, till the acceptance criterion as per
AERB/SS/CSE-1 standard is met.

Painting

BOQ of T. No. 2273 Page 4 of 18

 Amount in
Sl. No. Description of item Unit Quantity Rate in Rs.
Rs.

16 Providing and painting two (or) more coats with Epoxy

paint at all locations prepared and applied as per
manufacturer,s specifications including a priming coat if
specified by the manufacturer, preparation of surface by
cleaning with wire brush and rubbing with sand paper to
remove dust, dirt etc. after first coat Epoxy based trowelling
compound if required, including preparation of the surface
by scrapping, applying sand paper, by cleaning with wire Sq.M 1,500
brush and rubbing, making free of rust, dirt etc. filling the
holes, joints, cracks if anuy etc. complete all as per
manufacturers technical data and as directed at site to
achieve 200 micron film thickness (50 micron primer coat +
150 micron finishing coat)

17 Providing and applying Wall painting Two or more

coats on new work with Premium plastic emulsion paint
of (Asian paints or equivalentapproved brand and
manufacturer) to give an even shade, including a coat of Sq.M 9,000
approved Cement Primer, including preparation of the
surfaces, scaffolding complete. as per specifications and as
directed by the Project Engineer.
18 Providing, painting, finishing walls with two coats of anti-
algae, weather proof acrylic smooth emulsion paint of
approved make with silicon additives on sand face
plaster/plain plaster & concrete surfaces of required shade
over new work over a base coat of exterior cement primer Sq.M 3,600
including preparation of the surfaces, scaffolding complete.
as per specifications and as directed by the Engineer-in-
charge.

19 Prepatation of CONCRETE surfaces at all elevations to

receive the paint (interior/exterior/floor) including carrying
out minor rapairs, curing inclusive of all material, labours,
scaffolding, stagging, consumables, tools and tackles, etc.
complete as per specifications and as directed by Engineer.
it shall include, cutting the tie rods upto cover zone, filling all
form tie holes, localized air holes, repair of gradual
irregularities, removal of ridges and fins and abrupt
Sqm 4,500
irregularities by grinding. In addtion, filing air holes with
mortar and treatment of the entrie surface with sack
rubbing, applying cement mortar for making the surfaces
uniform. It shall also include clean up of loose and adhering
debris. The mortar used shall consist of one part cement to
one and half part by volume of fine sand passing IS No. 16
sieve.

Internal,external water supply and sanitary system

20 Providing, laying, jointing, fixing and testing heavy

quality (ISI Marked C-class) Galvanised iron pipes and
ISI marked fittings like. Tees, elbows bends, unions,
nipples, reducers etc. as required for the work, including
testing the pipes and fittings for 10.00 kg/sq. Cm hydralic
pressure with a minimum period of two hours duration with
clean water, including cutting, threading, jointing with hemp
yarn, white lead, jointing teflon tape, chasing walls and
making good by filling with concrete 1:3:6, complete all as
per specifications and drawings, including two coats of anti
corrosive bitumastic paint, all as directed by the Engineer-In-
Charge. pipe with ISI marked 'C'-Class heavy quality pipes
of approved make

20.1 15 mm dia G.I. pipe

RM 146

20.2 20 mm dia G.I. pipe

RM 150

20.3 25 mm dia G.I. pipe

RM 100

20.4 40 mm dia G.I. pipe

RM 200

20.5 50 mm dia G.I. pipe

RM 170

BOQ of T. No. 2273 Page 5 of 18

 Amount in
Sl. No. Description of item Unit Quantity Rate in Rs.
Rs.

21 Providing and laying non pressure NP2 class RCC

Hume pipes of approved make, with collars jointed with stiff
mixture of cement mortar in the proportion of 1:2, laying to
the levels, slopes and as per the drawings and
specifications and as directed by the Engineer-In-Charge
including testing of joints etc. complete.

21.1 100mm Dia RCC Hume pipe class NP2

RM 50

21.2 150mm Dia RCC Hume pipe class NP2

RM 200

22 Providing supplying, fixing in position, under floors or

in walls centrifugally cast iron pipes including required
specials like bends, tees, 'y' collars, cowl etc for soil, waste
and ventilation pipes conforming to IS 3989 of approved
make including cost of jointing with spun yarn and molten
lead of specified quantity, caulking the joints, including
testing of pipes, painting with primer, fixing at walls with
necessary approved type of clamps and brackets complete
all as per drawings and specifications and as directed at
site.

22.1 75 mm dia centrifugally cast (spun) iron socketed pipe

as per IS:3989 using 0.90 kg lead/joint RM 100

22.2 100 mm dia centrifugally cast (spun) iron socketed pipe

as per IS:3989 using 1.00 kg lead/joint RM 200

23 Providing and fixing PVC rain water downtake

conforming to IS:13592 Type A and PVC SWR fittings &
specials conforming to IS:14735, Finolex or other
approved equivalent make of pipes, fittings & specials
including jointing with seal ring / with PVC solvent
adhesive including fixing in walls /columns using RM 400
clamps, anchor fasteners, bolts and teakwood packing
pieces, joint testing etc. complete all as per drawings,
specifications and as directed by the EIC. PVC SWR
Rain water pipe 110 mm outer dia

24 Wash basin and its accessories

24.1 Providing and fixing white vitreous counter top wash

basin of size 610 mm X 450 mm of approved make
including making all connections but excluding the cost of
Nos 18
fittings etc. complete all as per specifications and as
directed by the Engineer-in-charge.

24.2 Providing heavy quality C.P. brass bottle trap 31/32 mm

of approved make single piece moulded with height of 270
mm, effective length of tail pipe 260 mm from the centre of
the waste coupling 77 mm bredth with 25 mm minimum Nos 18
water seal of approved make for wash basings / urinals etc.
all as per specifications and directed by the Engineer in
charge.

24.3 Providing heavy quality 15 mm C.P. brass piller cock

prestomatic auto closing of approved make as per
Nos 18
specifications and as directed by the Engineer in charge.

24.4 Providing PVC inlet connection pipes heavy quality

suitable for hot and cold including C.P. brass unions and
Nos 18
nuts 15 mm dia 450 mm long.

24.5 Providing heavy quality C.P. brass waste coupling of

40mm dia of approved make for wash basin and sink, size
Nos 18
and quality all as directed by Engineer in charge.

BOQ of T. No. 2273 Page 6 of 18

 Amount in
Sl. No. Description of item Unit Quantity Rate in Rs.
Rs.

24.6 Providing and fixing minimum 17 mm thick gang saw cut

mirror polished granite (premoulded and prepolished)
machine cut for kitchen platforms, vanity counters, wash
basin counters and similar locations etc. of required size of
approved Zebra black shade granite laid over 20 mm thick
base cement mortar 1:4 (using crushed sand) with joints
treated with white cement, mixed with matching pigment, SqM 35
epoxy touch ups, including rubbing, curing, moulding and
polishing the edge to give high gloss finish, cleaning etc.
complete as directed by the engineer-in-charge at all levels
including facia and drops of required width with epoxy resin
based adhesive wherever required.

24.7 Extra for providing edge moulding to 17 mm thick

Granite slab counters, Vanitis etc. including machine
polishing to edge to give high gloss finish etc. complete as RM 40
per design approved by Engineer-in-charge.

25 Providing and fixing white vitreous china European

type water closet with 'P' or 'S' trap with ISI marked white
solid plastic seat and lid complete of approved make. 10
litre low level white PVC flushing cistern with manually
controlled device (handle lever) conforming to IS: 7231,
flush bend fixing EWC with C.P. brass screws, 15 mm PVC Each 15
heavy quality inlet connection of 450 mm long, including
testing, commissioning & cleaning etc. complete all as per
drawings and specifications and as directed by the Engineer
in charge.

25.1 Providing, supplying and fixing JET spray with 1.00

metre long flexible tube connection in European / Anglo
Indian water closet under seat cover fixtures complete all as Each 15
specified and as directed by the Engineer-in-charge.

25.2 Providing and fixing 150 X 150 mm toilet paper roll

holder of white viterous china, "Hindware" or equivalent
approved make including C.P. brass paper roller, chasing
walls making good the same after fixing the toilet paper roll Each 15
holder etc. complete all as per specifications and as
directed by the Engineer in charge.

25.3 Providing and fixing Heavy Quality C.P Brass Health

Faucet with 1.50metres flexible hose (Hand Shower) of
“Jaquar continental model” or approved equivalent make
and type complete all as per specifications and as directed Nos 15
by the Engineer-in-Charge (Samples to be got approved by
the Engineer-in-Charge)

25.4 Providing and fixing 15 mm CP brass 2 in 1 bib cock

and angle cock combination of heavy quality of approved
make as per specifications and as directed by the Engineer- Nos 15
in-charge.

26 Providing and fixing white vitreous china flat back

single half stall urinal size 580 mm x 380 mm x 350 mm
/610 mm Aquaseal model of approved make with approved
make 32 mm C.P. brass prestomatic flush valve with
standard flush pipe and C.P. brass spreaders, 32 mm urinal
waste coupling with dome grating and clamp etc. including Each 9
making G.I. water line connection complete as directed by
the Engineer-in-charge (Only G.I. pipes will be paid under
relevant item)
Note: For fixing flush valve 32 mm GI. water line provision to
be made which will be paid under relevant item.

26.1 Providing and fixing 18 mm thick white Agaria Marble

stone slab table rubbed, edges rounded and polished of
size 750 X 500 mm and 18 mm thick fixed in urinal
partitions by cutting a chase of appropriate width with chase
cutter and embedding the stone in the chase with epoxy Nos 9
grout or with cement concrete 1:2:4 (using 6mm nominal
size aggregate) as per direction of Engineer in charge and
finished smooth.

BOQ of T. No. 2273 Page 7 of 18

 Amount in
Sl. No. Description of item Unit Quantity Rate in Rs.
Rs.

27 Providing and fixing satin finish stainless steel AISI 304

(18/8) kitchen sink of size 610X510 mm without drain
board and bowl size 685 X 535 X 250 mm depth as per IS
13983 of approved make, with C.I. brackets, fittings and
stainless steel plug 40 mm including painting the fittings and Each set 3
brackets with 3 coats of white enamel paint over a coat of
primer, cutting and making good the walls wherever
required complete as per specifications and as directed by
the Engineer-in-charge.

27.1 Providing and fixing heavy quality flexible PVC waste

pipe of 40 mm dia flexible PVC (semi-rigid) of approved
make for sink or wash basin including PVC waste fittings Each 3
etc. complete all as per specifications and as directed by the
Engineer-in-charge.

27.2 Providing and fixing heavy quality C.P. brass 15 mm dia

Long body bib cock of approved make for sink or wash
basin complete all as per specifications and as directed by Each 3
the Engineer-in-charge.

28 Shower rose and its accessories.

28.1 Providing and fixing C.P. brass wall mixer with provision
for over head shower complete with 115mm long bend pipe
on upper side, connecting legs and flanges CON -
273KNUPR (Jaquar CONTINENTAL series) or equivalent Each set 8
quality of GROHE/KOHLER as approved.

28.2 Providing and fixing CP brass100mm dia Shower rose

with shower arm of specified make all as per specifications
and as directed by the Engineer-in-Charge. (Samples to be Nos 8
got approved by the Engineer-in-Charge)

28.3 Providing and fixing C.P Brass towel rail 600mm long of
approved make complete fixed to walls with 30mm CP
brass screws with concealed fitting arrangement all as Each 19
directed by the Engineer-in-Charge.

28.4 Providing and fixing 150 X 150 mm Recessed type of

approved shade Vitreous china Soap dish of "Jaquar" or
equivalent approved make including chasing walls making
good the same after fixing the China Soap dish etc. Each 18
complete all as per specifications and as directed by the
Engineer-in-Charge

28.5 Providing and fixing 6mm thick first quality mirror of

required size with bevelled edges complete with 6 mm thick
asbestos/acrylic sheet back ground fixed to walls with C.P.
brass screws and concealed washers complete all as per SqM 15
specification and as directed by the Engineer-in-Charge.

28.6 Providing, hoisting at required level and fixing 25 litres

capacity stationary type, BEE approved 5 star rated
electric storage water heater conforming to IS 2082/
IS302 Part-2 Section21 of approved make including all
accessories like brass connector, fusible plug, non-return EACH 4
valve, pressure release valve, thermostat, CP stop/angle
cock of Jaquor make for inlet and outlet and all fittings and
fixtures complte as per specification and direction of the
Engineer-in-charge.

28.7 Providing and fixing CP Brass Concealed stop cock of

heavy quality as per specifications and as directed by the
Engineer-in-Charge. (Samples to be got approved by the Nos 6
Engineer-in-Charge)

28.8 Providing and fixing CP Brass Open stop cock of heavy

quality as per specifications and as directed by the Engineer-
in-Charge. (Samples to be got approved by the Engineer-in- Nos 6
Charge)

BOQ of T. No. 2273 Page 8 of 18

 Amount in
Sl. No. Description of item Unit Quantity Rate in Rs.
Rs.

29 Providing and fixing cast iron nahani trap / floor trap of

100 mm inlet and 75 mm outlet, (weighing 5.80 kg each),
jointing with lead with the connection pipes, placing as per
the drawings, embedding in cement concrete 1:2:4 and
making circular hole up to floor level using 110 mm O/D Each 29
PVC pipes of 6 kg/sq.cm pressure and fixing 1 No 125 mm
dia C.P brass grating, complete all as specifications and
drawings and as directed by the Engineer-in-charge

30 Providing and fixing square mouth S.W. gully trap (150

mm x 100 mm size gully trap "P" type) complete with CI
grating brick masonry chamber with water tight CI cover
with frame of 300 X 300 mm size (inside) the weight of Each 5
cover to be not less than 4.5 kg and frame to be not less
than 2.7 kg. as per standard design.

31 Providing and constructing inspection chambers of

internal size clear dimension of 900 mm x 600 mm in 230
thick brick masonry with cement mortar 1:4 ver a bed of 150
mm thick 1:4:8 cement concrete foundation, plastering with
cement mortar 1:4 20 mm thick on inside, outside and all
exposed surfaces finished with a floating coat of neat
cement, brick corbelling at top to provide opening of 900 x Each 10
450 mm, embedding the frame and cover with CC 1:2:4
concrete, and fixing cast iron steps if necessary at 300 mm
intervals complete. Depth of chamber not exceeding 900
mm, (excavation, soling, Cast iron cover and CI steps will
be paid separately under relevant item)

31.1 Supplying of Cast iron man hole cover or Cast iron Steps
of approved make and weight as specified in the drawings
Kgs. 700
or as directed by the Engineer-in-charge.

32 Fire Proof Doors:

32.1 Supplying, erecting including assembling and fixing
single / double leaf fire rated hollow galvanized MS
pressed steel flush doors of SIGNUM or equivalent
make conforming to IS : 3614 (Part-1), along with frame at
all elevations, with or without removable panels, with fire
rating of 1 hour using galvanised MS sheets for frames and
leaves, mineral wool / PUF/ any other fire retardant
insulation material, mastic caulking and grouting the frame,
reinforcing and insulating the shutters with fire retardant
material including heavy duty SS hinges, thresholds, fittings
complete with frame, fittings, fixtures, handles, aldrops,
latches, necessary access control hardware, necessary
gaskets, drop seal, smoke seal, etc for air tightness and
also providing a vision panel in each leaf for fireproof doors
using borosilicate float glass or approved equivalent of size
240 mm x 340 mm or as specified in drawing with same fire
rating including necessary beading, mastic cement, cleaning
and also all hardware as per door schedule including one
coat of approved primer and two coats of approved fire
resistant paint as necessary all complete such as a
complete package as per drawings, door schedules and
specifications. Including cost of Supply and installation SQ. M. 30
alongwith the cost of Single/ Double leaf swing-in / swing-
out doors of all size as per door schedule with two point
panic bar.

Note:
1. Tests as per IS:3614 Part-II standards for 1 hour fire
rating for full size door with vision panel and all fittings
and fixtures shall be conducted at approved laboratory
for 3 nos. of doors. One door shall be tested from the
first lot before shipment to site and remaining at
random from balance supply. No separate payment
shall be made for the testing including the door sample.
Fixtures given separately such as heavy duty door
closers shall be paid under the relevant item. Area
covered by outer surface of the door frame shall be
considered for the measurement under this item.
2. Payment @ 70 % shall be made against this item on
supply and acceptance of doors at site & balance 30 %
payment shall be made after successful installation of
doors with all fittings & fixtures, painting etc.

BOQ of T. No. 2273 Page 9 of 18

 Amount in
Sl. No. Description of item Unit Quantity Rate in Rs.
Rs.

33 Providing and Fixing 30mm thick factory made PVC

door shutters with door frames of approved colour/shade
“Sintex / Akrosha” or approved equivalent make and wall
thickness 2mm + 0.2mm with inbuilt edging on both sides.
The styles and rails mitred and joined at the corners,
including all accessories & fittings like 3 nos 100mm SS SqM 40
hinges, 2 Nos 125mm Grip aluminium Bow handles, 2 Nos
of Aluminium 75mm Baby latch for each door complete all
as directed at by the Engineer-in-Charge.

34 Supplying and erecting Single leaf/Double leaf doors of

all sizes including assembling, fitting and fixing factory
made swing-in/swing-out 45 mm thick hollow
galvanised heavy duty MS pressed steel flush doors(AS
per IS 4351) along with frame at all elevations,
single/double leafs, with or without top removable panels,
using galvanised MS sheets for frames and leaves, mastic
caulking and grouting the frame, reinforcing and insulating
with mineral wool or polyrethane foam as approved by the
Engineer including providing 6mm clear sheet glass vising
panel of 240 mm X 340 mm in each leaf, heavy duty SS
hinges, threshoulds, fittings complete with frame, fitting,
fixtures and all hardware such as aldrops, tower bolts,
handles, buffers, door stopers, necessary rubber gaskets/
Sqm 142
seal for achieving air-tightness etc. as a complete package
including one coat of approved primer and two coats of best
quality approved enamel paint as necessary all complete as
per drawings, door schedules, specifications as directed by
Engineer.
Note :
1) Fixtures given separately in this schedule for heavy duty
door closures and Mortice latches shall be paid separately
under relevant item. Clear opening shall be considered for
measurement.
2) payment @70% shall be made against the item on supply
and acceptance of the door and rest will be paid after
completion of work.

35 Door Fixtures & Fittings:

35.1 Providing and fixing IS:3564 marked aluminium die cast

body tubular type, universal extra heavy duty type
(Type - 3) door closure of approved make with necessary
accessories and screws etc. in steel doors with necessary Nos 111
bolts & nuts complete as per specifications and as directed
by the Engineer-in-charge.

35.2 Providing and fixing brass mortise latch and lock of

approved make with 6 levers and a pair of lever Brass
handles with necessary screws etc. complete suitable for Nos 111
fixing in wooden / steel / FRP / doors as per spscifications.

36 Providing and fixing SS grade 304, stainless steel

handrail mirror / matt finish 50mm dia 16 gauge thick With
machine bended edges for snap fitting, welding, cutting etc.
complete including stainless steel balusters and shoes,
providing and fixing with hand rail support using SS flat of
approved shape and size with necessary fixing arrangement Kg 6,200
all complete as per specifications and direction of engineer
in charge. Hand railing design & drawing shall be submitted
by the contracting agency for approval of Engineer in
charge.

Fabrication of Embedded Parts:

BOQ of T. No. 2273 Page 10 of 18

 Amount in
Sl. No. Description of item Unit Quantity Rate in Rs.
Rs.

37 Supply of material including its testing, fabrication of

embedded parts including cutting, bending, welding
and testing of welds as per NPCIL specifications PC-E-
160, complete as per drawings, specifications and as
directed by Engineer.
Material shall conform to IS 2062 Grade E250 Quality A,
BR, C, IS:1239, IS:3589 , ASTM -A-106 GR B, SA-193, SA-
194, Gr. 10.9, etc.
Note:
1. Temporary bracings and supports will not be measured
and paid.
2. Payment of hydrotest is deemed to be included in quoted
rates.
3. Payment of air hold tests is included in this item.

37.1 Anchor bolts and internal threaded EPs. Measurement shall

be for the weight of entire EP, including plates, lugs etc.
MT 50

37.2 Pipe & duct penetration EPs of all sizes

MT 5

37.3 All other EPs not covered above like plate, hatch frame,
edge angle, floor drain etc. MT 1

38 Structural steel: Supply of material including its testing,

fabrication and erection of structural steel items (rolled/ built
up sections) including welding or bolting connections with
bolts as required including testing on welds complete as per
drawing, specification and as directed by the Engineer.
Note:
1. All Bolts, nuts, screws and washers, which are
permanently incorporated in the structure, will not be paid.
2. Payment of HSFG bolts shall be made separately in the
relevant item.

Material conforming to IS:2062 Grade A or B, IS:1239,

IS:3589 etc.
38.1 Providing Structural steel work using angles, channels,
joists and other sections, welded and / or bolted in built
up sections for trusses, structural steel floors, frame works,
monorails and other structures including supplying, cutting,
welding, fabricating, hoisting fixing in position, applying a
priming coat of approved steel primer etc. complete all as
per specifications, drawings and as directed by the Engineer MT 1
in charge.
Up to and including 300 Joists, 350 mm channels, and
below sections using materials produced by SAIL /
RINL (Vizag Steel)/ TATA. All test reports to be provided
along with the supply of the materials.

38.2 Providing Structural steel work in MS Plain Plates and

chequrred Plates of Embedded Parts, Trench Covers,
Connections plates etc. including cutting, hoisting, fixing in
position and applying a priming coat of approved zinc
chromate steel primer etc. including cost of structural steel
Plates, welding all labour charges etc. complete as per
drawings and specifications. MT 2
Using materials produced by the own plants of SAIL, RINL
(Vizag Steel) and TATA only using virgin materials. All test
reports to be provided along with the supply of the materials.

38.3 Painting on steel surfaces

BOQ of T. No. 2273 Page 11 of 18

 Amount in
Sl. No. Description of item Unit Quantity Rate in Rs.
Rs.

38.3.1 Supply and application of approved epoxy paint conforming

to batch qualification given in table (vide Technical
Specification PC-E- 615)-on structural steel after its erection
and touch up with zinc sililcate primer wherever required,
with minimum DFT of 200 micron (excluding primer) at all
elevations after erection including surface preparation and
touch up with zinc silicate primer wherever required,
providing and removing scaffolding, all as per SQM 25
manufacturer's specifications, drawing and as directed by
Engineer in charge.
Note:
1) The rate shall be inclusive of surface preparation
with wire brushing and touch up with zinc silicate
primer.

38.3.2 Supply and application of approved make and shade

premium quality mat / glossy (as directed) finish
synthetic enamel paint minimum 2 coats to give an even
shade on steel surfaces at all elevations after erection
including surface preparation and touch up with zinc
phosphate primer wherever required, providing and
removing scaffolding, all as per manufacture's SQM 50
specifications, drawings and dierection of the Engineer.
Note:
1) the rate shall be inclusive of surface preparation with wire
brushing and touch up with zinc phosphate primer.

38.3.3 Supply and application of one coat of approved zinc silicate

primer on all steel surafaces as per the drawing
speficiations and as directed by the engineer, including shot SQM 2,100
blasting on steel surfaces after fabrication prior to
application of primer. DFT -75 to 85 micron.

39 Supplying and installing / grouting Anchor Fasteners

(mechanical / chemical) of following types of approved
make with necessary bolts / nuts and post installed
reinforcement using chemical grout including use of ferro
scan of minimum detection range of 300 mm to identify the
safe drilling location all complete as per drawing,
specifications and direction of Engineer.

39.1 Seismically qualified Anchors - Ductile

39.1.1 10 mm dia
EACH 10

39.1.2 12 mm dia
EACH 10

39.1.3 16 mm dia
EACH 10

39.2 Seismically qualified Anchors -Non Ductile

39.2.1 10 mm dia
EACH 10

39.2.2 12 mm dia
EACH 10

39.2.3 16 mm dia
EACH 10

39.2.4 20 mm dia
EACH 10

39.2.5 25 mm dia
EACH 10

40 Injection Grouting: Supply and injection of approved

grouting compound at various locations including providing
scaffolding, equipment, tools, labour etc. complete as per
drawing, specifications and direction of Engineer.

40.1 Using ultra low viscosity epoxy compound in concrete

KG 50

BOQ of T. No. 2273 Page 12 of 18

 Amount in
Sl. No. Description of item Unit Quantity Rate in Rs.
Rs.

40.2 Using neat cement grout

KG 122
40.3 Providing, fixing, cutting and finishing after grouting GI pipe
nozzles of 12mm dia and length upto half the thickness of
the concrete member at various locations prior to or after EACH 802
concreting as per specifications, drawings and as directed
by the Engineer
40.4 Extra over Item no.40.3 for providing non-return valve
packer type nozzles either in the GI pipe already or in
freshly drilled holes in concrete at various locations as EACH 500
directed by the Engineer

41 Grout /Dry Pack: Supply and place normal free flow

grut/dry pack at all places below equipment base plate,
structural steel base plates / bearing plates, anchor bolts,
pockets and other areas including preparation of surface,
roughening of concrete surface by chipping, equipments,
shuttering, scaffolding, labour, comacting, curring, finishing
etc. all complete as per drawings, speficifications and as
directed by the Engineer.

41.1 Mix 1:1 cement sand grout with approved anti-shrinkage

compound Cum 2

41.2 Mix 1:2 cement sand grout with approved anti shrinkage
compound Cum 2

41.3 Mix 1:1:2 grout with cement, sand and 6 mm down stone
chips with approved anti-shrinkage compound Cum 2

41.4 Mix 1:2.5 cement sand Dry pack mix with approved anti-
shrink compound Cum 2

41.5 Using approved cementiceous ready mix non-shrink

grouting compound of compressive strength not less than Cum 2
400 kg/sq.cm

42 Staircase Treads & Risers:

42.1 Providing and laying Minimum 25 mm thick uniform

shade Kotah stone treads and risers of steps, skirting,
window sills in single length up to 2.00 metres length slab
dado and pillars laid on 12 mm thick (average) cement
mortar 1:3 (using crushed sand) and jointed with grey SQ.M 350
cement slurry mixed with pigment to match the shade of the
slabs, including rubbing and polishing to obtain mirror finish
complete as per specifications, drawings and as directed by
the Engineer-in-charge.

42.2 Extra for Nosing in steps of treads Using Kotah stone.

R.M. 300

43 Caulking of Joints : Supplying, mixing and laying in

triangular /trapezoidal / any other shape as approved groove
of all sizes at construction joints and recess around
embedded parts at all levels, etc complete as per
specification and drawigs. (Measurement shall be done in
Cubic Centimeter)

43.1 Polysulphide caulking compound Cubic

2700000
Centimetre
43.2 Epoxy mortar Cubic
1350000
Centimetre
Active Drainage system

44 Supply of seamless SS pipes, fitting and its accessories

44.1 SS pipe of 100 NB size, sch.40, plain end conforming to

ASTM A 312 TP 304L RM 73

44.2 SS equal Tee, 100X100, BW end, sch.40, conforming to

ASTM A 403 Typ 304L Nos 18

44.3 SS, 100 NB, LR 90 degree Elbow, BW end, sch.40,

conforming to ASTM A 403 Typ 3041L Nos 6

BOQ of T. No. 2273 Page 13 of 18

 Amount in
Sl. No. Description of item Unit Quantity Rate in Rs.
Rs.

44.4 SS, 100 NB, 45 degree Elbow, BW end, sch.40, conforming

to ASTM A 403 Typ 304L Nos 3

44.5 SS, 100 NB, SORF flange conforming to ASTM A 182 F

304L Nos 7

44.6 SS, 100 NB, blind flange conforming to ASTM 182 F 304L
Nos 3
44.7 SS, 150 X 100 NB concentric re3ducer, BW end, sch.40,
conforming to ASTM A 403 Typ 304L Nos 15

44.8 SS, 3mm thk, perforated strainer plate (Standard/fabricated)

Nos 15

44.9 SS, 6 thk plate, conforming to ASTM A 240 Typ 304 L

Kg 100
45 Fabrication, erection, testing, etc. of burried/open drain
piping and its associated floor drain hub along with its
accessories.
45.1 Welding of SSxSS piping, fitting and accessories with or
without consumable inserts /filler/wire inserts, root pass Inch- Dia 500
GTAW with or without purging (butt welded)
45.2 DPT test (root and final) of weld joints
Inch- Dia 500
45.3 Radiaography of weld joints Inch- Dia 250
45.4 CS x SS (E-309L), SS x SS (E-308L) filler wire welding Cubic
using GTAW (butt and fillet) 50
Centimetre
45.5 Erection of water cleaned pipelines including its fitting and
accessories at site. RM 73

CONFIRMATORY SUB-SOIL INVESTIGATIONS:

46 Rotary boring/ drilling of ‘SX’ size holes to log and collect

samples through all kinds of soils vertically with adequate
and suitable equipment for depths below founding level as
per specifications, drawings and as directed by the
Engineer.
Note: The quoted rate shall include the following:
1. General clearance of site and removal of shrubs, bushes
etc required to commence the boring/ drilling operation & in-
situ tests in bore holes and clearance of site after
completion of work.
2. Making temporary access roads to the boring/ drilling
locations from existing approach roads to site.
3. Mobilization and Demobilization of minimum two sets of
suitable boring and drilling rigs of hydraulic type, including
necessary drilling rods, pumps, miscellaneous equipments,
tools, spares, consumables etc. adequate for each set of
plant, survey equipment, etc. Additional rigs and equipment
shall be mobilized if needed and disposing surplus
excavated earth upto lead of 1000m.
4. Marking the drill hole locations on ground by actual
survey as per the drawing, shifting and setting up of rig at
each bore hole location including staging, platform,
earthwork, anchoring etc. all complete.
5. Deployment of technical, skilled, semi skilled & unskilled
man power required for carrying out the complete work as
per specifications & drawings.
6. Measurement of ground water level as per specifications
& drawings.
7. Maintenance of drilling records and submission of final
geological logs in hardcopy as well as soft copy.
8. Conducting Standard Penetration Test (SPT) in the bore
holes @ every 1.5m depth.
46.1 0 M to 10 M
RM 10

BOQ of T. No. 2273 Page 14 of 18

 Amount in
Sl. No. Description of item Unit Quantity Rate in Rs.
Rs.

47 Same as item no. 46.0 but with NX size holes in rock

formations (excluding carrying out SPT) including
collection, numeration and logging of cores, supply of
wooden core sample boxes ,painting, labeling of boxes,
putting core samples in the boxes, labeling of cores
samples, colour photographs ( 100mm x 150 mm ) of
boxes with cores samples placed inside the boxes and
transporting and storing in core samples library at location
indicated by engineer, measurement of ground water level
etc. complete as per specifications & drawings.

47.1 0 M to 50 M
RM 300

48 FIELD TESTS

48.1 Conducting static plate load test on foundation rock as per

IS:12070 and specifications at the founding level upto 300
T/sq.m including preparation of test surfaces, clearance, all
Each 1
equipments, materials and preparation of test reports in
triplicate and one soft copy (CD)

48.2 Conducting vertical cyclic plate load test on foundation

rock as per IS:5249 and specifications at the founding level
upto 300 T/Sq.m including preparation of test surfaces, all
Each 1
equipment, materials and preparations of test report in
triplicate and one soft copy (CD)

48.3 Conducting double packer cyclic permeability test in

bed rock upto maximum pressure of 10Kg/sq.cm as per the
technical specifications and drawing. Each unit of this item
shall consist of a series of tests with pressure of three (3)
equal increments to the maximum and three (3) equal
decrements including submission of reports in triplicate and Sets 2
one soft copy (CD). The cost of drilling shall be paid in
relevant item. One set of the test consists of carrying out the
test at two depths of the same borehole.

48.4 GEOLOGICAL MAPPING: Cleaning, washing and removal

of loose materials by compressed air and brush and
conducting geological mapping on hard rock or weathered
rock at founding levels of Proposed OESC building by a
qualified geologist from approved organization/ Institute and
submission of final reports in triplicate and soft copy (CD)
complete as directed by the Engineer. Mapping shall include
horizontal, inclined and vertical surfaces.
1. Quoted rate includes preparation of the area, cleaning, Sq.m 2,200
offering for inspection, and getting the observation / report
from qualified geologist. 75% of payment shall be released
initially and balance 25% shall be released at the end, on
completion of geological mapping clearing the competent
strata.

48.5 Conducting cross-hole seismic test as per ASTM D 4428

/ IS: 13372 (Part 2) latest revision, at the location as
directed by the Engineer and as per specifications and
drawings Considering one hole for the source and 2 nos. of
receiver holes in orthogonal directions to a depth of 40 m
each from the foundation level, taking reading at every 1.5
m interval together with submission of test report. The test Each 1
shall be conducted by an approved agency.
The payment for the drilling of boreholes for conducting the
test is included in the item for drilling activities.

48.6 CONSOLIDATION GROUTING:(as per specifications &

IS:6066)

48.6.1 Drilling vertical holes of 76 mm dia in overburden soil &

disintegrated rock including supplying, fixing and removal of
Rm 10
casing pipe of suitable size etc.

BOQ of T. No. 2273 Page 15 of 18

 Amount in
Sl. No. Description of item Unit Quantity Rate in Rs.
Rs.

48.6.2 Drilling vertical holes of 76 mm dia in the foundation

hard rock/ concrete by "Percussion" means upto the
Rm 800
required depth.

48.6.3 Pressure testing of hole with water to the specified

pressure including use of mechanical packers. The
testing shall be carried out at three depths in the hole. The Sets 80
conducting of Pressure testing at three depths in the same
hole shall consist of one set.

48.6.4 Injecting grout under pressure by use of mechanical

packers. The rate shall also include plugging of holes with
cement mortar 1:2 after completion of grouting. Cost of
removal & fixing of packers shall be paid under separate
item.

48.6.4.1 Cement (with/without mineral fillers)

Kg of cement 12,000

48.6.4.2 Cement and sand grout mix as per specifications

Kg of cement 1,800

48.6.4.3 Supplying, fixing and removal of mechanical packers in 76

mm dia hole for grouting in a stage Stage 250

48.6.4.4 Drilling through grouted holes of 76 mm dia as specified

Rm 200

LABORATORY TESTS ON ROCK CORE SAMPLES

49 Carrying out laboratory tests on rock samples in an

approved laboratory, complete as per specifications and as
directed by Engineer-In-Charge, including necessary
transportation of samples to approved laboratories and
submission of test report in hardcopy (sixtuplicate) as well
as soft copy (CD).

49.1 Water content

Nos 6

49.2 Density and Specific Gravity

Nos 6

49.3 Uniaxial compression test to determine un-confined

compressive strength, Young's Modulus E and Poisson's
ratio with the samples in saturated condition. Nos 25

49.4 Tensile test by Point load method as per IS 8764 with the
samples in saturated condition. Nos 25

REPORT SUBMISSION OF THE SURVEYS, TESTS,

INVESTIGATIONS AND FOUNDATION PARAMETERS.
50 Preparation and submission of comprehensive draft ( 2
Copies ) and final (6 copies) reports of all the tests, field
investigations, surveys, laboratory tests etc. in the scope of
this tender as detailed in various schedules,
specifications, drawings inclusive of bore logs , survey of
discontinuities, Compilation, interpretation, analysis of the
data, recommendations of the foundation system and
foundation design parameters including deriving spring
constant as per AERB Guide no. AERB /NPP/SG/CSE-2.
Final report shall be submitted after the draft copy is
approved by the Engineer. Also submission of draft ( 2 Lumpsum 1
Copies) interim reports of all the tests / field investigations
carried out as detailed in specifications inclusive of bore
logs , results of tests including their soft copies and 3
copies of the approved interim report as soon as a particular
tests , investigation, surveys are completed. Report shall be
submitted in soft copies as well as hard copies. The report
shall be proof checked by a renowned geotechnical expert
from reputed institute to be approved by the Engineer.

SCHEDULE - "B" ELECTRICAL WORKS

Earth Grid and grounding works

BOQ of T. No. 2273 Page 16 of 18

 Amount in
Sl. No. Description of item Unit Quantity Rate in Rs.
Rs.

1 Grounding upto grade level and inside OESC building:

Supply, installation and testing of earthing system for On-
Site Emergency Support Centre building of following items
including all required consumables etc. for satisfactory
completion of work as per drawings, specifications and
installation notes.
1.1 Supply and installation of 95 sqmm. annealed, soft drawn RM 750
bare stranded tinned copper conductor (as per IS-613 & IS-
8130 and chemical composition as per ETP of IS-191) at
minimum 1000 mm deep in earth / rock laid in square matrix
format 3 mtr. spaced apart, with a minimum 300 mm
vertical clearance from pipe including excavation and back
filling for laying of conductor.

1.2 Supply and Execution of Exothermic welding for T-Joint Nos 220
suitable for 95 Sq.mm stranded copper conductor

1.3 Supply and Execution of Exothermic welding for X-Joint Nos 162
suitable for 95 Sq.mm stranded copper conductor

2 Supply and installation of earth pit comprising of 16mm dia Nos 10

3000 mm long Copper grounding electrode burried
minimum 3000mm deep into the earth with suitable parallel
groove clamps to connect 95 sq. mm copper stranded
conductor & carrying out civil jobs like construction of earth
pit chamber using bricks, cement & concrete earth pit
chamber cover.

3 Supply and installation of 65.09 sqmm. stranded Copper RM 1,000

ground conductor embedded in concrete (min. 100 mm
below surface).

3.1 Supply and Execution of brazing suitable to terminate 65.09 Nos 20

Sq.mm stranded copper conductor from embedded
concrete to grid (Refer attached drawing for details of earth
pads & brazing)

4 Supply, fabrication and installation of wall / floor / neutral

pads of the following sizes.

4.1 Supply and installation of cast copper alloy 70mmX70mm, 4 Nos 126
mm thick wall / floor / column pads (with 4 tapped holes for
10mm bolts along with the bolts) flushing its face fully with
wall / floor surface. (Refer for details of earth pads &
brazing at Section VI)

4.2 Supply and Execution of brazing to connect 65.09 Sq.mm Nos 126
stranded copper conductor with cast copper alloy
70mmX70mm, 4 mm thick wall / floor / column pads (Refer
for details of earth pads & brazing at Section VI)

4.3 Supply and Execution of brazing to connect 65.09 Sq.mm Nos 126
stranded copper conductor (from earth pad) with running
65.09 sqmm. Copper conductor in the embeded concrete
(Refer for details of earth pads & brazing at Section VI)

Lightning Protection System:

5.0 Supply, installation & testing of lightning protection system

for various plant buildings as per drawings, specifications
and installation notes.

5.1 Supply & installation of GS strip conductor 35 mm x 6 mm) RM 650

on columns, walls and roof slab including down comers &
connection to test link complete with all hardwares &
accessories including welding at suitable points to ensure
continuity of GS strips.

BOQ of T. No. 2273 Page 17 of 18

 Amount in
Sl. No. Description of item Unit Quantity Rate in Rs.
Rs.

5.2 Supply & installation of 3 mm thick Saddle & 3 mm thick Set 575
spacer with 2 nos. of 10 mm dia and 50mm long GS bolt,
nut and washer (for each saddle space set) to fix 35 mm x 6
mm GS strip on columns, walls and roof slab.

5.3 Supply & installation of Test links complete with all Nos 16
accessories at a height of 1 mtr. From ground and
connection to main earthing system ground rod.

5.4 Supply and Execution of brazing suitable to terminate 65.09 Nos 20

Sq.mm stranded copper conductor with Lightning arrester
test link.

5.5 Supply & installation of 65.09 sqmm. stranded Copper RM 40

conductor from test link to main earthing system ground rod
earth pit.

5.6 Supply of copper lightning arrester rods including its Nos 2

installation on top of building roof & connection with GS strip
conductor (35 mm x 6 mm) grid.

5.7 Supply & installation of concrete pedestral on roof top of Nos 100
dimensions 250mm X 250mm X 200mm for support &
installation of GS strip conductor (35 mm x 6 mm).

TOTAL Rs. 0.00

Note : - 1. Certified that the details as furnished above are true to the best of my / our knowledge and records. I/We give under taking that if at any stage of
scrutiny of tender or currency of this contract, any information submitted by me/us is/are found incorrect, the corporation shall have the right to reject the
bid/terminate the contract at its discretion and I/We shall have no claim for any compensation whatsoever thereof.

2. All the terms and conditions of NPCIL’s laid in the tender documents are acceptable to us and we have not made any deviations from the same or put forward
any additional conditions in our offer.

3. Quoted amount shall be inclusive of all statutory liabilities, taxes including GST, cess, duties, levies etc

BOQ of T. No. 2273 Page 18 of 18