Scribd Logo
Upload

Welcome to Scribd!

  • 63 views

    Description: 1 of 2 mp-01010 C

    Uploaded by

    koalaboi
    This document specifies the requirements for non-oriented, annealed electrical lamination sheet steel that is either 0.5mm or 0.65mm thick. It outlines the required electrical and magnetic properties including specific total iron loss, magnetic flux density, and sheet insulation coating. It also specifies mechanical properties, dimensions and tolerances, packing and handling requirements, and notes that the supplier is responsible for providing test certificates when requested.

    Copyright:

    © All Rights Reserved
    Download as PDF, TXT or read online from Scribd

    Description: 1 of 2 mp-01010 C

    Uploaded by

    koalaboi
    63 views2 pages
    This document specifies the requirements for non-oriented, annealed electrical lamination sheet steel that is either 0.5mm or 0.65mm thick. It outlines the required electrical and magnetic properties including specific total iron loss, magnetic flux density, and sheet insulation coating. It also specifies mechanical properties, dimensions and tolerances, packing and handling requirements, and notes that the supplier is responsible for providing test certificates when requested.

    Original Title

    MP-01010_Rev_C_8WKg

    Copyright

    © © All Rights Reserved

    Available Formats

    PDF, TXT or read online from Scribd

    Did you find this document useful?

    Is this content inappropriate?

    This document specifies the requirements for non-oriented, annealed electrical lamination sheet steel that is either 0.5mm or 0.65mm thick. It outlines the required electrical and magnetic properties including specific total iron loss, magnetic flux density, and sheet insulation coating. It also specifies mechanical properties, dimensions and tolerances, packing and handling requirements, and notes that the supplier is responsible for providing test certificates when requested.

    Copyright:

    © All Rights Reserved
    Download as PDF, TXT or read online from Scribd
    Download as pdf or txt
    63 views2 pages

    Description: 1 of 2 mp-01010 C

    Uploaded by

    koalaboi
    This document specifies the requirements for non-oriented, annealed electrical lamination sheet steel that is either 0.5mm or 0.65mm thick. It outlines the required electrical and magnetic properties including specific total iron loss, magnetic flux density, and sheet insulation coating. It also specifies mechanical properties, dimensions and tolerances, packing and handling requirements, and notes that the supplier is responsible for providing test certificates when requested.

    Copyright:

    © All Rights Reserved
    Download as PDF, TXT or read online from Scribd
    Download as pdf or txt
    of 2

    Description

    Non-oriented, annealed, electrical lamination sheet steel, 0.5 or 0.65 mm thick.


    Details
    Sheet steel must conform to EN 10106, unless otherwise stated.

    APPROVED DOCUMENT
    Electrical and magnetic properties
    Thickness 0.5 and 0.65 mm
    Maximum specific losses of 8 W/kg measured at 1.5T flux density, 50Hz frequency. Normal distribution
    Specific total iron loss
    of specific loss should be given by standard deviation of 0.33 W/kg or smaller.
    Magnetic field intensities of 2.5, 5 and 10 A/mm should result in magnetic flux densities no smaller than
    Magnetic flux density
    1.62, 1.72 and 1.84 T respectively.
    Both sides of sheet steel to be coated. Coating must possess an electrical resistance greater than
    Sheet insulation coating 10 Ohms/cm2 per side and be able to withstand continuous temperatures as high as 180 deg C.
    Coating should not be damaged by the stamping and welding processes.

    Mechanical properties in the longitudinal and transverse directions


    Minimum yield strength 285 MPa
    Minimum tensile strength 430 MPa
    Vickers hardness 150-185 HV
    Minimum stacking factor 0.95

    ISSUE/ERN A 4-1497-01 B 4-9474-01 C 5-0733-01 D E F G H CHECKED: PH


    DRAWN/DATE SFA 13/05/97 SAP 06/03/08 TC 29/07/10 APPROVED: AJB
    MATERIAL PROPERTIES Sheet Document Number Issue
    CONFIDENTIAL Property of
    ANNEALED LAMINATION STEEL, 0.5 OR 0.65 MM THICK,
    Cummins Generator Technologies Ltd.
    MAX 8W/KG LOSS @ 1.5T/50HZ 1 of 2 mp-01010 C
    The supplier will be responsible for providing electrical and mechanical test certificates when requested to do so by CGT’s Quality Department.
    Test certificates must contain: reference/coil number, grade, thickness and width, specific losses measured at 1.5 T / 50Hz, flux densities for
    2.5, 5 & 10 A/mm, and coating resistance. All measured.
    For traceability purposes it is understood that the supplier will carry out periodic checks and hold all results/records for an archive period of
    10 years.

    Dimensions and tolerances

    APPROVED DOCUMENT
    Residual curvature: Less than 25mm. Between 25 and 35mm CGT will require a concession from the supplier.

    Sheet thickness 0.5 mm +/-0.03mm or 0.65 mm +/-0.04 mm


    Roll width Refer to chart drawing.
    Edge camber Max. deviation 0.5 mm in 1 m
    Wave factor (flatness) Max. Deviation 2%
    Roll edge burr Not to exceed 0.05 mm
    Thickness range Sheet thickness not to vary by more than 0.02 mm across the coil width, this excluding the outer
    40mm portions pertaining to the sides.

    Packing & Handling


    All coils to be labelled at the start of the coil and the inside bore, as well as externally.
    Max roll diameter 1250 mm
    Max/min roll weight Based on roll width - refer to chart drawing.

    Material should be capable of being processed through lamination punching, notching on progression tools, welding and other manufacturing
    processes. We reserve a right to return material which doesn’t go through our process satisfactorily. After three unsuccessful trials CGT will offer
    the supplier an opportunity to witness the fault, if requested.

    MATERIAL PROPERTIES Sheet Document Number ISSUE


    CONFIDENTIAL Property of
    ANNEALED LAMINATION STEEL, 0.5 OR 0.65 MM THICK,
    Cummins Generator Technologies Ltd.
    MAX 8W/KG LOSS @ 1.5T/50HZ
    2 of 2 mp-01010 C

    You might also like