Scribd Logo
Upload

Welcome to Scribd!

  • 942 views

    Wrangler Trouble Code c123c

    Uploaded by

    julio montenegro
    jeep

    Copyright:

    © All Rights Reserved
    Download as PDF, TXT or read online from Scribd

    Wrangler Trouble Code c123c

    Uploaded by

    julio montenegro
    942 views3 pages
    jeep

    Original Title

    wrangler trouble code c123c - copia

    Copyright

    © © All Rights Reserved

    Available Formats

    PDF, TXT or read online from Scribd

    Did you find this document useful?

    Is this content inappropriate?

    jeep

    Copyright:

    © All Rights Reserved
    Download as PDF, TXT or read online from Scribd
    Download as pdf or txt
    942 views3 pages

    Wrangler Trouble Code c123c

    Uploaded by

    julio montenegro
    jeep

    Copyright:

    © All Rights Reserved
    Download as PDF, TXT or read online from Scribd
    Download as pdf or txt
    of 3

    2012 Jeep Truck Wrangler V6-3.6L Copyright © 2013, ALLDATA 10.

    52SS Page 1

    A L L Diagnostic Trouble Codes ( DTC ): C Code Charts


    C123C
    C123C-DYNAMICS SENSOR MOUNTING/INSTALLATION PERFORMANCE

    For a complete wiring diagram, refer to the Wiring Information.


    2012 Jeep Truck Wrangler V6-3.6L Copyright © 2013, ALLDATA 10.52SS Page 2

    - When Monitored:
    With vehicle speed above 7 mph (11 km/h), but not if the sensor signal is invalid.

    - Set Condition:
    If the Anti-Lock Brake Module detects implausible Dynamics Sensor values.

    1. VERIFY DTC IS ACTIVE

    NOTE: If present, diagnose and repair DTC C2114-DYNAMICS SENSOR SUPPLY VOLTAGE LOW or DTC C2115-DYNAMICS
    SENSOR SUPPLY VOLTAGE HIGH before diagnosing this DTC.

    1. Turn the ignition on.


    2. With the scan tool, read and record the ABS DTCs.
    3. With the scan tool, read and record the Environmental Data to help identify the conditions in which the DTC was set.
    4. With the scan tool, erase the ABS DTCs.
    5. Cycle the ignition switch.

    WARNING: Make sure brake capability is available before road testing.

    6. Test drive the vehicle by turning the vehicle left or right in a curving manner at a velocity between 6 and 12 mph (10 and 20 km/h).
    7. Park the vehicle.
    8. With the scan tool, read the ABS DTCs.

    Does this DTC reset?

    Yes

    - Go To 2

    No

    - The condition that caused the symptom is currently not present. Inspect the related wiring for a possible intermittent condition. Look for any
    chafed, pierced, pinched or partially broken wires.
    - Perform the ABS-INTERMITTENT CONDITION TEST. See: Brakes and Traction Control/Antilock Brakes / Traction Control Systems/Testing
    and Inspection/ABS Intermittent Condition Test.

    2. CHECK THE DYNAMICS SENSOR INSTALLATION

    NOTE: Dynamics Sensor installation and mounting bolt torque is crucial for proper operation.

    1. Turn the ignition off.


    2. Check the Dynamics Sensor for damaged, modified and bent mounting brackets.
    3. Check the Dynamics Sensor mounting bolts for a loose or over tightened condition.

    Were any problems found?

    Yes

    - Repair as necessary.
    - Perform the ABS VERIFICATION TEST. See: Verification Tests/ABS Verification Test.

    No

    - Go To 3

    3. INSPECT RELATED WIRING HARNESS, TERMINALS, AND CONNECTORS


    1. Visually inspect the related wiring harness. Look for any pinched, chafed, pierced and partially broken wires.
    2. Visually inspect the related wiring harness connectors. Look for broken, bent, pushed out and corroded terminals.
    2012 Jeep Truck Wrangler V6-3.6L Copyright © 2013, ALLDATA 10.52SS Page 3

    Were any problems found?

    Yes

    - Repair as necessary.
    - Perform the ABS VERIFICATION TEST. See: Verification Tests/ABS Verification Test.

    No

    - Replace the Dynamics Sensor.


    - Perform the ABS VERIFICATION TEST. See: Verification Tests/ABS Verification Test.

    You might also like