100% found this document useful (1 vote)
425 views2 pages

SI816N Module (8 Inputs + 16 Static Outputs) : Technical Characteristics

The SI816N module has 8 digital inputs and 16 static outputs. It uses an RS485 serial connection for communication and has LED indicators to show operational status. The inputs accept 24VDC and the outputs can source up to 700mA each while protecting against overloads and short circuits. Physical dimensions and mounting details are provided.
Copyright
© © All Rights Reserved
We take content rights seriously. If you suspect this is your content, claim it here.
Available Formats
Download as PDF, TXT or read online on Scribd
100% found this document useful (1 vote)
425 views2 pages

SI816N Module (8 Inputs + 16 Static Outputs) : Technical Characteristics

The SI816N module has 8 digital inputs and 16 static outputs. It uses an RS485 serial connection for communication and has LED indicators to show operational status. The inputs accept 24VDC and the outputs can source up to 700mA each while protecting against overloads and short circuits. Physical dimensions and mounting details are provided.
Copyright
© © All Rights Reserved
We take content rights seriously. If you suspect this is your content, claim it here.
Available Formats
Download as PDF, TXT or read online on Scribd
You are on page 1/ 2

SI816N module (8 Inputs + 16 Static outputs)

1
7
6
5
4
3
2
1
0
GND
24VIN

NC
A
B

WD
INPUT

L1

L2
NET
CNI SI816N
OUT OUT

+24V
+24V

GND

GND
7
6
5
4
3
2
1
0

7
6
5
4
3
2
1
0
1

1
Technical characteristics:
General characteristics: with VIN =24V typ 10 mA
Power supply voltage 24 Vdc Delay times
Input voltage range Vdc 15% Vdc low-to-high transition max 2 msec
Maximum Power supply high-to-low transition max 2 msec
(without inputs) 2W Logical status visualization green leds
Serial connection IOS system Connection pull-out terminal
board (screw type)
type RS485
transmission speed 750 K baud Static outputs Technical characteristics:
diagnosis
Serial led (yellow) OK=alwais on Single overload and
WD led (yellow) OK=blinking short-circuit protection
f = 6 Hz approx. Number of outputs 16
Rated input voltage VIN 24Vdc
Input Technical characteristics:
Supply voltage VIN range 12 - 35V
Number of inputs 8 Output current IOU T max 700 mA
Rated input voltage VIN 24 Vdc Output voltage for
Input voltage VIN high state (IOU T =0,7A) min Vout = VIN - 0,3V
high state min 16 V Clamp diode for
low state max 8 V inductive load 1A
Input voltage VIN Logical status visualization red leds
accidental tolerance max 110 Vac Connection pull-out terminal
Input current board (screw type)

SI816N
Physical dimensions and Installation

130
33.5

Dia.4 Dia.4
70
33.5

125
4.5 116 4.5
67
View of side with installation
brackets for DIN bar

-1 -
SI816N
EXTERNAL CONNECTIONS

J2A DS1 J1A DIP-SWITCH DS1

1
BINARY ADDRESS 0 .. 31

6 N.C.

7
6
5
4
3
2
1
0
GND
24VIN

NC
A
B

5 BIT 16
WD

INPUT
L1

L2

NET
ON = 1 4 BIT 8
CNI SI816N
OFF = 0 3 BIT 4
OUT OUT

+24V
+24V

GND

GND 2 BIT 2
7
6
5
4
3
2
1
0

7
6
5
4
3
2
1
0
1 BIT 1

ON OFF
1

1
J2B J1B

J1A J1B
OUT 0 1
IN 0 1

OUT 1 2
IN 1 2

OUT 2 3
IN 2 3

OUT 3 4
IN 3 4

OUT 4 5
IN 4 5

OUT 5 6
IN 5 6

OUT 6 7
IN 6 7

OUT 7 8
IN 7 8

9
9 NC +24V
+24V
10
10 GND GND

J2A J2B
1
1 VIN GND
24V DC SUPPLY
WD 2 0V 2
+24V
3
OUT 0 3
SERIAL 4 0V serial
SERIAL OUT 1 4
5 B
CONNECTION
6 A OUT 2 5

OUT 3 6

OUT 4 7

J1A : 10 pin pull-out terminal board (screw type)


OUT 5 8
J2A : 6 pin pull-out terminal board (screw type)
OUT 6 9
J1B : 10 pin pull-out terminal board (screw type)
J2B : 10 pin pull-out terminal board (screw type) OUT 7 10

-2 -

You might also like