CE6501-Structural Analysis-I

Download as pdf or txt
Download as pdf or txt
You are on page 1of 17

CE6501-STRUCTURAL ANALYSIS – I

QUESTION BANK

UNIT – I

INDETERMINATE FRAMES

PART A

1. Differentiate determinate and indeterminate of structure

2. Differentiate static and kinematic indeterminacy of structure

3. What is equilibrium condition

4. Define degree of indeterminacy

5. What are the methods of structure to determining the degree of indeterminacy

6. What are all type of frames

7. Differentiate external and internal indeterminacy of structures

8. Define redundant force

9. To find degree of indeterminacy of structures as given below

10. To find degree of indeterminacy of structures as given below

11. Define strain energy


12. State Castigliano’s second theorem
13. Name any energy method to analysis a redundant frame and briefly explain it.
14. Differentiate the method of joints & method of sections
15. What are temperature stresses? Explain.
16. Define trussed beam
17. What is a portal frame?
18. Briefly explain about consistent deformation method?
19. Define rigid frame.
20. Explain a pin-jointed frame with a sketch

PART B

1. Determine the force in the members of the truss shown in figure. The cross
sectional area of vertical and horizontal members is 4000mm 2 and that of the
diagonal is 6000 mm2.

2. Find the forces in the members of truss shown in figure. The cross sectional
area and young’s modulus of all the members are the same.

3. Find the forces developed in all the members of truss shown in fig, if the
temperature of member AC goes up by 20°c. Take the co efficient of thermal
expansion α=12X10-6/°c. Cross sectional area of all the members is 2500mm2
and young’s modulus is 200KN/mm2.
4. In the frame ABCD shown in fig, end A is fixed and end D is on roller. Analyse
the frame for the loading shown.

5. Analyses the frame shown in fig, using the consistent deformation method.
Flexural rigidity is constant throughout.

6. Find the stresses in all the members of the given frame, in which the cross
sectional areas of vertical members are 3000mm2 each and those of all other
members are 2200mm2. E=2x10^5 N/mm2.

7. Determine the forces in the members of the truss shown. AE is constant for all
the members
8. A two span continuous truss is loaded as shown. All the members are of the
same material and have the same cross sectional area. Find the reaction at
the central support C. also fined the forces in all the members of the truss.

9. Find the forces in all the members of the pin-jointed frame work as show. All
the members have the same area of cross section and Young’s modulus.

10. A braced cantilever truss is loaded as shown. All the members are of the same
material and have the same cross-sectional area. Find the axial force in the
member AD.
UNIT- II

MOVING LOADS AND INFLUENCE LINES (DETERMINATE & INDETERMINATE


STRUCTURES WITH REDUNDANCY RESTRICTERD TO ONE)

PART – A

1. State importance of ILD.

2. State Muller Breslau‟s principle?

3. What are the types of connections possible in the model of begg‟s deformeter?

4. What is the influence line diagram?

5. Draw influence lines for support reactions in a simply supported beam?

6. What do you understand by an influence line for bending moment?

7. When a series of wheel loads move along a girder, what is the condition for
getting maximum bending moment under any one point load?

8. Draw a qualitative influence line diagrams for the support reactions of a simply
supported beam of span L?

9. What is meant by absolute maximum bending moment in a beam?

10. What is the absolute maximum bending moment due to a moving udl longer than
the span of a simply supported beam?

11. What are the three types of connections possible with the model used with
Begg‟s deformeter?

12. What is Begg‟s deformeter?

13. Where do you get rolling loads in practice?

14. Name the type of rolling loads for which the absolute maximum bending moment
occurs at the mid span of a beam?

15. Define similitude?

16. What is the principle of dimensional similarity?

17. Where do you have the absolute maximum bending moment in a simply
supported beam when a series of wheel loads cross it?
18. State the location of maximum shear force in a simple beam wit h any kind of
loading?

19. What is meant by maximum shear force diagram?

20. State Maxwell-Betti‟s theorem?

PART – B

1. A system of four loads 80, 160, 160 and 120 kN crosses a simply supported beam of
span 25m with the 120 kN load leading. The loads are equally spaced at 1m. Determine
the values of the following using influence lines.

i. Maximum bending moment at a section 10m from left support and

ii. Absolute maximum shear force and bending moment in the beam.

2. A beam has a span of 24m, draw the influence line diagram for the bending moment
and shear force at a section 8m from the left and also determine maximum bending
moment and shear force at this section due to two point loads of 10kN and 6kN at a
fixed distance of 2m apart rolling from left to right with 6kN load leading

3. Two point loads of 100kN and 200kN spaced 3m apart cross a girder of span 12
meters from left to right with the 100kN leading. Draw the ILD for shear force and
bending moment and find the values of maximum bending moment and find the values
of maximum shear force and bending moment at a section 4m from the left hand
support. Also evaluate the absolute maximum bending moment due to the given loading
system.

4. A simply supported beam has a span of 16m,is subjected to a UDL(dead load) of


5kN/m and a UDL(live load) of 8kN/m(longer than the span) travelling from left to right.
Draw the ILD for shear force and bending moment at a section 4m from left end. Use
these diagrams to determine the maximum shear force and bending moment at this
section.

5. The following system of wheel loads crosses a span of 25m


Wheel load (KN) 16 16 20 20
20

Distance between centre (m) 3 3 4 4

6. Draw the influence line for MB for the continuous beam ABC simply supported at A and
C using Muller Breslau`s principle. AB=3m, BC=4m.EI is constant.

7. Draw the influence line diagram for the propped reaction of a propped cantilever
beam having span 6m. EI=Constant.

8. Determine the influence line diagram for bending moment at a point D, the middle
point of span AB of a continuous beam ABC of span AB=6m and BC=4m simply
supported at supports A,B and C. Compute the ordinates at every 1m interval.

9. The warren girder of 25m span is made of 5 panels of 5m each. The diagonals are
inclined at 60° to the horizontal. Draw the influence line diagram for force in upper chord
member in the second panel from left. Hence evaluate the forces in it when there is load
of 60 kN at each lower joint.

10. Draw the influence line for RA for the continuous beam ABC of span AB = BC = 4m
simply supported at A, B &C. Compute the ordinates at every 1m interval, EI
= constant.

UNIT – III

ARCHES

PART – A

1. What is an arch? Explain.

2. What are the methods used for analysis of fixed arches?

3. Distinguish between two hinged and three hinged arches?

4. Give the equation for a parabolic arch whose springing is at different levels?

5. State Eddy‟s theorem as applicable to arches?


6. Explain the effect of temperature on the horizontal thrust of a two hinged arch
subjected to a system of vertical loads?

7. Indicate the positions of a moving point load for maximum negative and positive
Bending moments in a three hinged arch.

8. Write down the expressions for radial shear and normal thrust in a three hinged
parabolic arch?

9. Define radial shear and normal thrust.

10. Mention the examples where arch action is usually encountered?

11. What is a linear arch?

12. What is the degree of static indeterminacy of a three hinged parabolic arch?

13. Under what conditions will the bending moment in an arch be zero throughout?

14. Distinguish between two hinged and three hinged arches?

15. In a parabolic arch with two hinges how will you calculate the slope of the arch at
any point?

16. How will you calculate the horizontal thrust in a two hinged parabolic arch if there
is a rise in temperature?

17. What are the types of arches according to their shapes?

18. What are the types of arches according to their support conditions?

19. Draw the influence line for radial shear at a section of a three hinged arch?

20. Write the formula to calculate the change in rise in three hinged arch if there is a
rise in temperature.

PART – B

1. A circular three hinged arch of span 25m with a central rise of 5m is hinged at the
crown and the end supports. It carries a point load of 100 kN at 6m from the left support
.Calculate

i. The reaction at the supports

ii. Moment at 5m from the left support.


2. A three hinged circular arch of span 16m and rise 4m is subjected to two point loads
of 100 kN and 80 kN at the left and right quarter span points respectively. Find the
reaction at the supports. Find also the bending moment, radial shear and normal thrust
at 6m from left support.

3. A symmetrical three hinged arch has a span of 50 & rise 5m. Find the maximum
bending moment at a quarter point of the arch caused by a uniformly distributed load of
10kN/m which occupies any portion of the span. Indicate the position of the load for this
condition.

4. A three hinged parabolic arch of span 30m and rise 5m carries a uniformly distributed
load of 40kN per meter on the whole span and a point load of 200kN at a distance of 5m
from the right end. Find the horizontal thrust, resultant reaction, bending moment and
normal thrust at a section 5m from the left end.

5. A three hinged parabolic arch has supports at different levels having span 20m and
carries a UDL of 30kN/m over the left half of the span. The left support is 5m below the
crown and the right support is 4m below the crown. Draw the BMD. Also find the
normal thrust and radial shear at a section 4m from the left support.

6. A parabolic two hinged arch has a span of 40m and a rise of 5m. A concentrated load
10kN acts at 15m from the left support. The second moment of area varies as the
secant of the inclination of the arch axis. Calculate the horizontal thrust and reactions at
the hinge. Also calculate maximum bending moment at the section.

7. Evaluate the horizontal thrust in a two hinged parabolic arch of span 10m and rise
25m carrying an UDL of 24 kN/m over the left half span, assuming secant variation of its
sectional moment of area. Also calculate the Bending Moment at the crown and draw
the BMD.

8. Derive the expression for horizontal thrust in a two hinged parabolic arch carrying a
point load P at distance one fourth span from left support .Assume I=Io Secθ.
9. A two hinged parabolic arch of span L and rise h carries a triangular load covering a
distance a from the left end ,the intensity varying uniformly from zero to W. Obtain an
expression for the horizontal thrust.

10. Derive the expression for horizontal thrust in a two hinged semi circular arch of
radius R, carrying a point load W at the crown.

UNIT – IV

SLOPE DEFLECTION METHOD

PART – A

1. Write down the equilibrium equations used in slope deflection method?

2. What is the basic assumption made in slope deflection method?

3. Give the fixed end moment for the beam shown in fig?

4. What is the moment at a hinged end of a simple beam?

5. Write down the slope deflection equation for fixed end support?

6. Write the general equations for finding out the moment in a beam AB by using
slope deflection equation?

7. What are the quantities in terms of which the unknown moments are expressed
in slope deflection method?

8. What is meant by distribution factor?

9. Say true or false and if false, justify your answer “slope deflection method is a
force method”?

10. What are the reasons for sway in portal frames?

11. What are the sign conventions used in slope deflection method?

12. Why slope-deflection method is called a displacement method?

13. State the limitations of slope deflection method?


14. Mention any three reasons due to which sway may occur in portal frames?

15. Who introduced slope-deflection method of analysis?

16. Write the fixed end moments for a beam carrying a central clockwise moment?

17. What is the basis on which the sway equation is formed for a structure?

18. How many slope-deflection equations are available for each span?

19. What is the moment at a hinged end of a simple beam?

20. Define degree of freedom.

PART – B

1.Analyse the rigid frame shown in fig. by slope deflection method and draw the bending
moment diagram.

2. A Continuous beam ABCD fixed at A and D and continuous over supports B and C.
The span AB=5m carries a central concentrated load of 10kN. The span BC=4m carries
a uniformly distributed load of 4 kN/m over the entire span of BC. The span CD=6m
carries a non central concentrated load of 8 kN acting at a distance of 2m from the end
D. Analyse the beam and draw bending moment diagram using slope deflection
method.

3. A continuous beam ABC consist of span AB=3m and BC=4m, the ends A and C
being fixed. AB and BC carry uniformly distributed loads of intensity 4kN/m and 5kN/m
respectively. Find the support moments and draw the bending moment diagram for the
beam .The beam is of uniform section throughout.
4. Analyse the portal frame shown in fig. by slope deflection method. EI = constant.

5. Analyse the beam shown in fig. by slope deflection method and draw the SFD and
BMD.EI=Constant.

6. Analyse the continuous beam ABCD shown in fig. by slope deflection method .Take
EI=Constant. Also sketch the shear force and Bending Moment diagram.

7. Analyse the continuous beam shown in fig. by slope deflection method. Support B
settles by 8mm and C settles by 12 mm. I=60000cm4,E=210x106kN/m2.Draw the SFD
and BMD.
8. Draw the BMD and SFD of the beam shown in fig. by slope deflection method.

9. A Continuous beam of constant moment of inertia is loaded as shown in fig. Find the
support moments and draw the B.M diagram.

10. Analyse the portal frame shown in fig. by slope deflection method.

UNIT- V

MOMENT DISTRIBUTION METHOD


PART – A

1. Define Stiffness?

2. State how the redundancy of a rigid frame is calculated?

3. Explain carry over factor and distribution factor?

4. What is carry over moment?

5. Give the relative stiffness when the far end is (a) Simply supported and (b) Fixed.

6. What is sway corrections?

7. What are the advantages of Continuous beam over simply supported beam?

8. How is the moment induced at a fixed end calculated when a moment M is


applied at the end of prismatic beam without translation?

9. What is the difference between absolute and relative stiffness?

10. What are the advantages of continuous beams over simply supported beams?

11. Define: Moment distribution method (Hardy Cross method)

12. Define: Distribution factor

13. Define: Stiffness factor

14. Define: Flexural Rigidity of Beams

15. Define sway

16. What are the situations where in sway will occur in portal frames?

17. Find the distribution factor for the given beam?

18. Define: Continuous beam?

19. What is the sum of distribution factors at a joint?

20. Write the distribution factor for a given beam?

PART – B

1.Analyse the frame shown in fig. by moment distribution method & draw the SFD &
BMD.
2. Analyse the frame shown in fig. by moment distribution method.

3. Analyse the continuous beam shown in fig. by the method of moment distribution.

4. A beam ABC 5.8 meters long is fixed at A and simply supported at B,4 meters from A
so as to provide an overhang BC 1.8 meters long. It carries a point load of 5kN at C.
Analyse the beam.

5. Draw BMD and SFD of the beam shown in fig. by moment distribution method. EI
constant.
6. Analyse the continuous beam shown in fig. and plot the BMD and SFD. Use Moment
distribution method.

7. Analyse the continuous beam shown in fig. and plot the BMD and SFD. Use Moment
distribution method. EI is constant.

8. Draw the SFD and BMD for the beam shown in fig. by moment distribution method.

9. Analyse the continuous beam shown in fig. by moment distribution method. Draw
BMD.
10. Analyse the portal frame ABCD shown in fig. by moment distribution method & also
draw the bending moment diagram.

You might also like