APPLICATION MANUAL

PWM switching regulator controller IC

TK11840L

CONTENTS
1 . DESCRIPTION 2
2 . FEATURES 2
3 . APPLICATIONS 2
4 . PIN CONFIGURATION 2
5 . PACKAGE OUTLINE 2
6 . BLOCK DIAGRAM 3
7 . ABSOLUTE MAXIMUM RATINGS 4
8 . ELECTRICAL CHARACTERISTICS 5
9 . TEST CIRCUIT 6
10 . TYPICAL CHARACTERISTICS 6
11 . CIRCUIT DESCRIPTION 8
12 . APPLICATIONS INFORMATION 13 MEETING YOUR NEEDS
13 . NOTES 15
14. OFFICES 15

GC3-I015 Page 1
 TK11840L

PWM switching regulator controller IC

TK11840L

1. DESCRIPTION 4. PIN CONFIGURATION

The TK11840L is a step-up DC-DC converter that drives
an external NPN power transistor using a constant
EaIn 1 8 FB
frequency PWM architecture.
The IC works with a wide operating supply range (1.8V SCP 2 7 OSC
to 10V) and has an adjustable output.
The IC timing oscillator operating frequency is Vcc 3 6 GND
programmable and can be set up to 1MHz.
The TK11840L incorporates a soft-start circuit, which BR/CTL 4 5 Out
ensures that the output pulse width starts from 0 % duty
cycle and builds up to its proper level gradually when the
IC is first powered up.
The TK11840L also incorporates a short-circuit detection 5. PACKAGE OUTLINE
function of a timer-latch type.

n SOT23L-8
2. FEATURES 6 4
n Operation from 1.8V to 10V supply.
n Adjustable output voltage.
n High speed adjustable OSC. (Up to 1MHz)

1.6 ±0.2
nIncorporates a soft start circuit.
nIncorporates a short circuit detection of a timer-latch.
nTotem-pole type output in which current is adjustable
using an external resistor.(Pin 4) 1 3

n1µA or less shutdown current.

+0.10
0.3 −0.05
0.1 M

nLow component count. 0.95 0.95

nSmall 8 Pin SOT23L-8 package.

2.9 ±0.2

3. APPLICATIONS
(0.3)

n White LED Backlighing and Frontlighting.

1.3max

1.1 ±0.1

n Step-up DC-DC Converters

n Mobile Communication Systems:
+0.10
0.13 −0.05
0~0.1

Cellular Phone,PHS,DSC,PDA
2.8 ±0.2
n Computer Peripherals Equipment 0.1

n Battery Powered System

n Portable Equipment Unit : mm

GC3-I015 Page 2
 TK11840L

6. BLOCK DIAGRAM

Pin No. Symbol Description

1 EaIn Error amplifier inverting input
Feed back input. Threshold voltage is 0.5V . Connect resistive
divider tap to this pin.
2 SCP Soft start and Short circuit detection
Connect external capacitor Cscp to this pin.
3 VCC Power Supply Voltage Input
4 BR/CTL Output current setting and shutdown
5 Out Totem-Pole type Output
Connect to base of external NPN switching transistor.
6 GND Ground
7 OSC Oscillation frequency setting pin
Connect external capacitor Ct and resistor Rt to this pin.
8 FB Error amplifier output
Compensation pin for error amplifier. Connect capacitor Cfb
from FB pin (pin 8) to GND.

Error Amplifier
1 FB
EaIn 8

0.5V
PWM Comparator
OSC
7
SCP Soft Start
2 Short Circuit Protection Oscillator

Vcc GND
3 6
1.3V
Reference Output Drive
Voltage Supply Control Circuit Out
5
BR/CTL
4

GC3-I015 Page 3
 TK11840L

7. ABSOLUTE MAXIMUM RATINGS

Ta=25°C
Parameter Symbol Rating Units Conditions
Supply Voltage VCC 10 V
Power Dissipation PD 400 mW *
Storage Temperature Range Tstg -55 ~ +150 °C
Operating Temperature Range TOP -40 ~ +85 °C
Maximum Operating Frequency fMAX ~ 1000 kHz
Operating Voltage Range VOP 1.8 ~ 10 V
* PD must be decreased at rate of 3.2mW/°C for operation above 25°C.

GC3-I015 Page 4
 TK11840L

8. ELECTRICAL CHARACTERISTICS
VCC=2V, Ta=25°C
Value
Parameter Symbol Units Conditions
MIN TYP MAX
Circuit to prevent malfunction
at low input voltage
Reset voltage VCC, Reset - - 0.9 V
Threshold voltage VCC, On 1.1 1.3 1.5 V
Soft start
Charging current ISS -1.8 -1.2 -0.84 µA VSCP=0V
Threshold voltage VSS, TH 0.65 0.75 0.85 V
Short circuit protection (S.C.P)
Charging current ISCP -1.8 -1.2 -0.84 µA VSCP=0V
Threshold voltage VSCP, TH 0.65 0.75 0.85 V
Oscillator
Frequency fOSC 440 550 660 kHz Rt=3kΩ, Ct=270pF
Frequency input stability fÄV - 2 10 % VCC=2.0V~10V
Frequency variation
fÄT - 5 - % Ta=-20°C~85°C
with temperature
Error Amplifier
Threshold voltage VEa 480 500 520 mV VFB=0.45V
Line regulation VEaÄV - 1 4 % VCC=2.0V~10V
Variation with temperature VEaÄT - 1 - % Ta=-20°C~85°C
Input bias current IEaIn -1.0 -0.2 1.0 µA VEaIn=0V
Voltage gain AV 35.5 38.5 41.5 dB
Gain Band Width GBW - 6 - MHz AV=0dB
Output high voltage VEaOut, High 0.78 0.87 - V VEaIn=0V
Output low voltage VEaOut, Low - 0.05 0.2 V VEaIn=1.0V
Output source current IEaOut, Source - -40 -24 µA VFB=0.45V
Output sink current IEaOut, Sink 24 40 - µA VFB=0.45V
Dead time control
Maximum duty cycle DMAX 65 75 85 %
Output driver
Output high voltage VOut, High 1.0 1.2 - V IOut=-15mA
Output low voltage VOut, Low - 0.1 0.2 V IOut=15mA
Output source current IOut, Source - -30 -20 mA VOut=0.9V
Output sink current IOut, Sink 30 60 - mA VOut=0.3V
Pull-down resistor ROut 20 30 40 kΩ
Output drive control
Pin voltage VBR 0.25 0.35 0.45 V RBR=620Ω
Input off condition IBR, Off -15 - 0 µA
Input on condition IBR, On - - -45 µA
Pin current range IBR -0.9 - -0.1 mA
Entire device
On mode ICC, On - 5.0 9.0 mA RBR=620Ω
Supply
Current
Off mode ICC, Off - 0.1 1.0 µA BR/CTL Pin=VCC
Latch mode ICC, LT - 5.3 9.5 mA S.C.P. is operating

GC3-I015 Page 5
 TK11840L

9. TEST CIRCUIT

1 EaIn FB 8
0.1μF
2 SCP OSC 7

1μF TK11840L 3kΩ

3 Vcc GND 6 270pF
2.0V
4 BR/CTL Out 5
620Ω

10. TYPICAL CHARACTERISTICS

n Supply current vs. Supply voltage (On mode) n EaIn threshold voltage vs. Supply voltage
Ta=25°C, RBR=620Ω Ta=25°C
10 1000
EaIn threshold voltage VEa (mV)

8 800
Supply current I CC (mA)

6 600

4 400

2 200

0 0
0 2 4 6 8 10 0 2 4 6 8 10
Supply Voltage V CC (V) Supply Voltage V CC (V)

n EaIn threshold voltage variation ratio vs. Supply voltage n EaIn threshold voltage variation ratio vs. Ambient
Ta=25°C temperature VCC=2.0V
10.00 10.00
EaIn threshold voltage variation ratio (%)
EaIn threshold voltage variation ratio (%)

5.00 5.00

0.00 0.00

-5.00 -5.00

-10.00
-10.00
-20 0 20 40 60 80 100
0 2 4 6 8 10
Ambient temperatureTa (℃)
Supply voltage V CC (V)

GC3-I015 Page 6
 TK11840L

n Output source current vs. BR/CTL pin current n BR/CTL pin voltage vs. BR/CTL pin current
VCC=2.0V, Ta=25°C VCC=2.0V, Ta=25°C

-50 600
(mA)

500

BR/CTL pin voltage VBR (mV)

-40
Out

400
Output source current I

-30
300
-20
200

-10 100

0 0
-0.1 -0.3 -0.5 -0.7 -0.9 -0.1 -0.3 -0.5 -0.7 -0.9
BR/CTL pin current I BR (mA) BR/CTL pin current I BR (mA)

n Oscillation frequency vs. Timing resistor n Frequency variation ratio vs. Supply voltage
VCC=2.0V, Ta=25°C Ct=270pF, Rt=3kΩ, Ta=25°C
1000 10.00
Ct=100pF
Oscillation frequency fOSC (kHz)

Frequency variation ratio (%)

Ct=270pF
5.00

Ct=1000pF

100 0.00
Ct=3300pF

-5.00
Ct=10000pF

10 -10.00
1 10 0 2 4 6 8 10
Timing resistor Rt (kΩ) Supply voltage VCC (V)

n Frequency variation ratio vs. Ambient temperature

VCC=2.0V, Ct=270pF, Rt=3kΩ

10.00
Frequency variation ratio (%)

5.00

0.00

-5.00

-10.00
-20 0 20 40 60 80 100
Ambient temperature Ta (℃)

GC3-I015 Page 7
 TK11840L

11. CIRCUIT DESCRIPTION

12-1. Setting the output voltage 12-2. Shutdown

To obtain a regulated output voltage for most common To disable the device (shutdown mode), set BR/CTL Pin
step-up regulator applications, connect a voltage-divider (Pin 4) open or connect to VCC as shown in Fig 2.
from the output (Vout) to EaIn. (See Fig1) During shutdown, the supply current of the IC drops to
1µA or less.
The output voltage is determined by the 0.5V reference
level and by the selection of two external resistors
according to the equation.

 R2  4 BR/CTL
Vout = VRe f × 1 + 
 R1 
Rb
where VRef=0.5V

The input bias current of EaIn has -0.2µA.typical .

Vout

R2
Fig2: Shutdown
Error amplifier
EaIn
1

R1
VRef=0.5V

Fig1: Setting the output voltage

GC3-I015 Page 8
 TK11840L

12-3. Sawtooth wave Oscillator

The oscillator operates by rapidly charging an external
OSC
capacitor Ct and resistor Rt with a current from a lower
7
threshold voltage VOSC,L to an upper threshold voltage
VOSC,H.
Once the Ct voltage reaches the upper threshold voltage, Ct Rt
the capacitor is slowly discharged back through resistor
Rt to the lower threshold voltage.
The oscillator frequency can be expressed as
Fig 4. Oscillator pin connection
1
f OSC ≈
VOSC , H
Ct ⋅ Rt ⋅ ln + t Rise
VOSC , L
VOSC,H
where VOSC,H=800mV 800mV
VOSC,L=100mV
tRise=0.1µSec

This equation is rough estimate, because it takes no

account of overshoot around the upper threshold level
when Ct is charged rapidly. VOSC,L
A plot of OSC frequency vs. Rt and Ct is shown in Fig 3. Fall Time 100mV

Rise Time
1000
Ct=100pF * tRise=0.1µSec
Oscillation frequency fOSC (kHz)

Ct=270pF
Fig 5. Oscillator waveform

Ct=1000pF

100
Ct=3300pF

Ct=10000pF

10
1 10
Timing resistor Rt (kΩ)

Fig.3: Oscillator frequency vs. Timing resistor

GC3-I015 Page 9
 TK11840L

12-4. Setting the output source current

The TK11840L is designed to drive an external bipolar Rb=3kΩ Rb=2kΩ Rb=1kΩ Rb=620Ω
600
NPN switching transistor, enabling high efficiency
conversion with low input voltages. 500

BR/CTL pin voltage VBR (mV)

Rb=470Ω
The output current which is a base current of the NPN
switching transistor is set by a resistor Rb at pin4. 400
This function ensures optimum efficiency over a wider
300
range of load currents. The optimum Rb value should be
determined by experiment in an actual circuit.
200
VCC=1.8V
Vin VCC=2.0V
100
VCC=10V
L
TK11840L Di 0
0 -0.1 -0.2 -0.3 -0.4 -0.5 -0.6 -0.7 -0.8 -0.9 -1
Out BR/CTL pin current I BR (mA)
5 NPN Tr.
Fig 7. BR/CTL pin voltage vs. BR/CTL pin current

4 BR/CTL

-50
Output source current IOut,Source (mA)
Rb

-40

-30
Fig6: Programming output current
-20
The output current can be expressed as
I Out ,source = α ⋅ I BR
-10
V
I BR = BR
Rb 0
where, VBR is a voltage across the resistor Rb at pin4. IBR 0 -0.2 -0.4 -0.6 -0.8 -1
is the current through Rb to GND. BR/CTL pin current IBR (mA)
α :A proportional coefficient which is approximately 50.

Fig.7 shows BR/CTL pin voltage (VBR) vs. BR/CTL pin Fig 8. Output source current vs. BR/CTL pin current
current (IBR).

Fig.8 show output source current (IOut, Source) vs. BR/CTL

pin current (IBR).

For example follows

IOut,source=-10mA
IBR=-0.2mA (from Fig.8)
VBR=0.4V (from Fig.7)
VBR
∴ Rb = = 2kΩ
I BR

The value of output source current (IOut,Source) is 50mA

maximum.

GC3-I015 Page 10
 TK11840L

12-5. Maximum output source current

Soft start time (the time until the output ON duty reaches
Power dissipation within the IC package is a maximum approximately 50%) is determined by
150mW at Ta= 85°C (ambient temperature)
The power dissipation of IC increases directly with input Cscp[µF]
t SS [S] ≈ ⋅ 0.4[V ] ≈ 0.33 ⋅ Cscp[µF]
I SS [µA ]
voltage and output current, which can be expressed as the
following relation.

where ISS is internal current source of 1.2µA (Typ.).

PD ≈ VCC ⋅ I Out ,Source ⋅ Duty
After soft start operation is over, the voltage of SCP pin
Fig.9 shows an allowable output current setting area returns low and enters the short circuit detection wait
(safety area) under this condition. (150mW at Ta=85°C) state. When an output short circuit occurs as output
Output current must be set within the safe area. (which is suddenly drops due to load effect, the error amplifier
lower than 50mA and "Duty line" in application circuit.) output is fixed at VEaOut,High and capacitor Cscp starts
charging with about 1.2µA. When the voltage of Cscp
100 reaches about 0.75V, the output pin (pin5) is set low and
IOut,source,max IOut,source,max the SCP pin (pin2) stays low.
90 (Duty75%) (Duty50%) Short circuit detection time is
Out・Source (mA)

80
Cscp[µF]
70 Maximum current t SCP [S] ≈ ⋅ 0.75[V ] = 0.625 ⋅ Cscp[µF]
of output source
Rb=680Ω I SCP [µA ]
60
Output source current I

(I Out,Source=50mA)
50 where ISCP is internal current source of 1.2µA (Typ.).
Rb=1k Ω
40

30 Safety area
20 SCP
2
10

0 Cscp
0 2 4 6 8 10

Supply voltage V CC (V)

Fig 9. Output source current vs. supply voltage Fig 10. SCP pin connection

Once the protection circuit operates, the timer latch

12-6. Soft start and Short circuit detection circuit can be restored by resetting the power supply.
The TK11840L incorporates a soft start function and Fig.11 shows the timing Diagram of soft start and short
short circuit detection.
circuit detection.
A capacitor Cscp connected to the SCP pin (pin2) is a
dual purpose capacitor, one is for soft start function and
Note :
the other is for short circuit detection. When the IC is first In application of the simple step-up circuit, the short
activated, the capacitor Cscp on the SCP pin is charged
circuit detection circuitry is not in series with the power
with about 1.2µA by internal current source. path from input to load.
The PWM comparator compares the soft start setting This short circuit detection makes the external switch
voltage as a proportion of the voltage at the SCP pin with transistor turn off only.
the sawtooth waveform. The ON duty of the output pin is
gradually increased by the PWM comparator output
signal.

GC3-I015 Page 11
 TK11840L

Timing Diagram of soft start and short circuit detection.

FB pin voltage
Idle period
setting voltage
OSC pin waveforms
SCP pin waveforms discharge

Out pin waveforms

softstart Short Circuit Output off

DC-DC converter
return Short Circuit
output voltage

Fig.11: Timing Diagram of soft start and short circuit detection.

In Out

L
DC-DC converter
FB pin voltage
output voltage
Error amplifier
1 FB
EaIn 8

0.5V OSC pin

SCP pin
PWM comparator waveforms
waveforms 7
OSC

SCP Soft start

2
Short circuit protection Oscillator

Idol period setting voltage GND

3 6
VCC
1.3V
Reference Output drive
voltage supply control circuit Out
5
BR/CTL
4
Out pin
waveforms

CTL

Fig.12: Minimum step-up application

GC3-I015 Page 12
 TK11840L

12. APPLICATIONS INFORMATION

n Step-up DC-DC converter application

Typical application for 2.7V to 5V 100mA DC-DC Converter.

· Vin=2.7V
· Vout=5.0V
· Iout=100mA

Figure13: 2.7V to 5V 100mA DC-DC Converter

Vin=2.7V L D
Vout=5.0V
Iout=100mA
VIn

Cin Error Amplifier Cout

1 FB
EaIn 8

0.5V Cfb
PWM Comparator
OSC R2
7
SCP Soft Start
2 Short Circuit Protection Oscillator Ct
Cscp
Rt
GND
3 6
VCC
1.3V
Reference Output Drive
Voltage Supply Control Circuit Out
5
BR/CTL
4

Rb SW Tr.
R1

CTL (ON/OFF)

· Value of component
L= 15µH (TOKO D52LC TYPE *Parts No.A914BYW-150M)
Cin=10µF/6.3V, Cout=10µF/6.3V
Cfb=0.1µF, Cscp=0.1µF
Ct= 270pF , Rt= 2.2kΩ (Oscillator Frequency 730kHz)
Rb=2.0kΩ
R1=10kΩ, R2=91kΩ (Vout=5.0V)

· Output voltage setting

Set the output voltage by selecting values for R1 and R2.
The regulated output voltage is determined by
 R2 
VOut = VRe f 1 + 
 R1 
VRe f = 0.5V

GC3-I015 Page 13
 TK11840L

n White-LED Drive application

Typical application for 6LEDs/20mA in series.

· Vin=2.5V
· ILED=20mA

Figure14: White-LED Driver (6LEDs in series)

In L D Out

VIn

Cin Error Amplifear Cout

1 FB
EaIn 8
W-LED
0.5V
PWM Comparator
OSC
7
SCP Soft Start
2 Short Circuit Protection Oscillator Ct
Cscp
Rt
GND
3 6
VCC
1.3V
Reference Output Drive RLED
Voltage Supply Control Circuit Out
5
BR/CTL Sw.Tr
4

Rb

CTL

· Value of component
L=10µH (TOKO D52LC TYPE *Parts No.A914BYW-100M)
Cin=4.7µF, Cout=2.2µF
Ct=270pF, Rt=6.8kΩ (Oscillator Frequency:260kHz)
Cfb=0.1µF, Cscp=0.1µF
Rb=2.0kΩ
VRe f 0 .5
RLED=24Ω ( I LED = = = 20.8mA )
R LED 24

· LED current setting

The LEDs current (ILED) is set by an external resistor (RLED) connected between the EaIn pin and GND.
The current of each LED is same as
VRe f
I LED =
R LED
where VRef : the feedback reference voltage 0.5V

Output voltage Vout is given by

Vout = n ⋅ Vf + VRe f
where Vf : LED forward voltage drop
n : Number of LEDs in series connection

GC3-I015 Page 14
 TK11840L

13. NOTES 14. OFFICES

n Please be sure that you carefully discuss your planned If you need more information on this product and other
purchase with our office if you intend to use the products in TOKO products, please contact us.
this application manual under conditions where particularly
extreme standards of reliability are required, or if you intend n TOKO Inc. Headquarters
to use products for applications other than those listed in this 1-17, Higashi-yukigaya 2-chome, Ohta-ku, Tokyo,
application manual. 145-8585, Japan
l Power drive products for automobile, ship or aircraft TEL: +81.3.3727.1161
transport systems; steering and navigation systems, FAX: +81.3.3727.1176 or +81.3.3727.1169
emergency signal communications systems, and any Web site: http://www.toko.co.jp/
system other than those mentioned above which include
electronic sensors, measuring, or display devices, and n TOKO America
which could cause major damage to life, limb or property Web site: http://www.toko.com/
if misused or failure to function.
l Medical devices for measuring blood pressure, pulse, n TOKO Europe
etc., treatment units such as coronary pacemakers and heat Web site: http://www.tokoeurope.com/
treatment units, and devices such as artificial organs and
artificial limb systems which augment physiological n TOKO Hong Kong
functions. Web site: http://www.toko.com.hk/
l Electrical instruments, equipment or systems used in
disaster or crime prevention. n TOKO Taiwan
Web site: http://www.tokohc.com.tw/
n Semiconductors, by nature, may fail or malfunction in
spite of our devotion to improve product quality and n TOKO Singapore
reliability. We urge you to take every possible precaution Web site: http://www.toko.com.sg/
against physical injuries, fire or other damages which may
cause failure of our semiconductor products by taking n TOKO Seoul
appropriate measures, including a reasonable safety margin, Web site: http://www.toko.co.kr/
malfunction preventive practices and fire-proofing when
designing your products. n TOKO Manila
Web site: http://www.toko.com.ph/
n This application manual is effective from Feb. 2002 Note
that the contents are subject to change or discontinuation n TOKO Brazil
without notice. When placing orders, please confirm
Web site: http://www.toko.com.br/
specifications and delivery condition in writing.

n TOKO is not responsible for any problems nor for any

infringement of third party patents or any other intellectual MEETING YOUR NEEDS
property rights that may arise from the use or method of use
of the products listed in this application manual. Moreover,
this application manual does not signify that TOKO agrees
implicitly or explicitly to license any patent rights or other
intellectual property rights which it holds. TO BUILD THE QUALITY RELIED BY COSTOMERS

n None of ozone depleting substances(ODS) under the

Montreal Protocol is used in manufacturing process of us.

YOUR DISTRIBUTOR

GC3-I015 Page 15