Scribd
Upload
57 views6 pages

MATLAB Code For Speed Control of 3 - Induction Motor Using Constant V/F Control

The MATLAB code calculates the torque-speed curves for a 3-phase induction motor under constant V/f control at different frequencies. It takes input parameters like supply voltage, frequencies, pole number, resistances and reactances. It then calculates the voltages, synchronous speeds and torque values in arrays for each frequency using motor equations. Finally, it plots the torque-speed curves on the same graph for comparison.

Uploaded by

Ankit Bhatt
Copyright
© © All Rights Reserved
We take content rights seriously. If you suspect this is your content, claim it here.
Available Formats
Download as DOCX, PDF, TXT or read online on Scribd
57 views6 pages

MATLAB Code For Speed Control of 3 - Induction Motor Using Constant V/F Control

The MATLAB code calculates the torque-speed curves for a 3-phase induction motor under constant V/f control at different frequencies. It takes input parameters like supply voltage, frequencies, pole number, resistances and reactances. It then calculates the voltages, synchronous speeds and torque values in arrays for each frequency using motor equations. Finally, it plots the torque-speed curves on the same graph for comparison.

Uploaded by

Ankit Bhatt
Copyright
© © All Rights Reserved
We take content rights seriously. If you suspect this is your content, claim it here.
Available Formats
Download as DOCX, PDF, TXT or read online on Scribd
You are on page 1/ 6

MATLAB Code for Speed Control of 3- Induction motor using Constant V/f

control
Vll=input('Suppy Voltage (line to line) RMS value @ 50 Hz: ');
f2=input('Enter the second frequency: ');
f3=input('Enter the third frequency: ');
f4=input('Enter the fourth frequency: ');
f5=input('Enter the fifth frequency: ');
P=input('Enter the number of poles: ');
Rs=input('Stator Resistance: ');
Rr=input('Rotor Resistance: ');
Xs=input('Stator Leakage Reactance @ 50 Hz frequecny: ');
Xr=input('Rotor Leakage Reactance @ 50 Hz frequecny: ');
Ls=Xs/(2*pi*50);
Lr=Xr/(2*pi*50);
Vlnf1=Vll/(3^0.5);
Vlnf2=Vlnf1*f2/50;
Vlnf3=Vlnf1*f3/50;
Vlnf4=Vlnf1*f4/50;
Vlnf5=Vlnf1*f5/50;
Wsync1=4*pi*50/P;
Wsync2=4*pi*f2/P;
Wsync3=4*pi*f3/P;
Wsync4=4*pi*f4/P;
Wsync5=4*pi*f5/P;
Tmf2=zeros(Wsync2*500+1,1);
Tmf3=zeros(Wsync3*500+1,1);
Tmf4=zeros(Wsync4*500+1,1);
Tmf5=zeros(Wsync5*500+1,1);
Tmf1=zeros(Wsync1*500+1,1);
m=1;
for Wrotor1=0:0.002:Wsync1
Tmf1(m)=(3*(((Vlnf1^2)*Rr/((Wsync1-Wrotor1)/Wsync1))/((Rs+Rr/((Wsync1-
Wrotor1)/Wsync1))^2+(2*pi*50*Ls+2*pi*50*Lr)^2))/Wsync1); %star connected
m=m+1;
end
m=1;
for Wrotor2=0:0.002:Wsync2
Tmf2(m)=(3*(((Vlnf2^2)*Rr/((Wsync2-Wrotor2)/Wsync2))/((Rs+Rr/((Wsync2-
Wrotor2)/Wsync2))^2+(2*pi*f2*Ls+2*pi*f2*Lr)^2))/Wsync2);
m=m+1;
end
m=1;
for Wrotor3=0:0.002:Wsync3
Tmf3(m)=(3*(((Vlnf3^2)*Rr/((Wsync3-Wrotor3)/Wsync3))/((Rs+Rr/((Wsync3-
Wrotor3)/Wsync3))^2+(2*pi*f3*Ls+2*pi*f3*Lr)^2))/Wsync3);
m=m+1;
end
m=1;
for Wrotor4=0:0.002:Wsync4
Tmf4(m)=(3*(((Vlnf4^2)*Rr/((Wsync4-Wrotor4)/Wsync4))/((Rs+Rr/((Wsync4-
Wrotor4)/Wsync4))^2+(2*pi*f4*Ls+2*pi*f4*Lr)^2))/Wsync4);
m=m+1;
end
m=1;
for Wrotor5=0:0.002:Wsync5
Tmf5(m)=(3*(((Vlnf5^2)*Rr/((Wsync5-Wrotor5)/Wsync5))/((Rs+Rr/((Wsync5-
Wrotor5)/Wsync5))^2+(2*pi*f5*Ls+2*pi*f5*Lr)^2))/Wsync5);
m=m+1;
end
plot(Tmf1);
hold on;
plot(Tmf2);
plot(Tmf3);
plot(Tmf4);
plot(Tmf5);
hold off;
ylabel('Torque(N-m)');
xlabel('Rotor Speed(Rad/s) * 100');
end

Suppy Voltage (line to line) RMS value @ 50 Hz: 400

Enter the second frequency: 45

Enter the third frequency: 40

Enter the fourth frequency: 35


Enter the fifth frequency: 50

Enter the number of poles: 4

Stator Resistance: .05

Rotor Resistance: .01

Stator Leakage Reactance @ 50 Hz frequecny: 15

Rotor Leakage Reactance @ 50 Hz frequecny: .05

You might also like