MODEL 3005A /3007A: Instruction Manual

3007A-E 01.9.
12 11:52 AM ページ表4
DISTRIBUTOR INSTRUCTION MANUAL
Kyoritsu reserves the rights to change specifications or designs

described in this manual without notice and without obligations.
KYORITSU ELECTRICAL
INSTRUMENTS DIGITAL INSULATION-CONTINUITY TESTER
WORKS, LTD.
No.5-20,Nakane 2-chome, Meguro-ku, Tokyo
152-0031 Japan
MODEL 3005A /3007A
Phone :(03) 3723-0131 Fax : (03) 3723-0152
URL : http://www.kew-ltd.co.jp
E-mail : [email protected] KYORITSU ELECTRICAL INSTRUMENTS
Factories : Uwajima & Ehime WORKS, LTD.
01-09 92-1492A
Quality Kyoritsu Products Online at: www. GlobalTestSupply.com [email protected]
3007A-E 01.9.12 11:52 AM ページ目1
CONTENTS 1. SAFTY PRECAUTIONS

1. SAFETY PRECAUTIONS ······································································· 1 ○ The instrument is designed to produce in accordance with the following
2. FEATURES ···························································································· 4 standards and supplied in the best conditions after successfully clearing
3. SPECIFICATIONS ················································································· 5 the inspection.
4. INSTRUMENT LAYOUT ········································································· 9
4-1 Instrument layout ············································································· 9 ・IEC 61010-1 Overvoltage CAT III 300V Pollution Degree 2
4-2 LCD ································································································ 10 ・IEC 61010-2-31 (Safety requirements for hand-held probe assemblies)
4-3 Connector ······················································································· 11
5. PREPARATION FOR MEASUREMENT ··············································· 12 This instruction manual describes warnings and safety rules which must be
5-1 Removing the Cover ······································································· 12 observed by the user to ensure safety operation of the instrument and to
5-2 Battery Voltage Check ····································································· 12 retain it in safe condition. Therefore, read through these instructions before
5-3 Test Probe Connection ··································································· 12 using the instrument.
6. OPERATION ·························································································· 13
6-1 Disconnection and Check of Power Source of WARNING
the Circuit under Test ····································································· 13 ● Read through and understand instructions contained in this manual
6-2 Insulation Resistance Measurement ··············································· 14 before using the instrument.
6-3 Continuity Measurement (Resistance Tests) ·································· 16 ● Save and keep the manual handy to enable quick reference whenever
6-4 Continuous Measurement ······························································· 17 necessary.
7. FUNCTIONS ·························································································· 18 ● The instrument must only be used by a competent trained person and
7-1 TRAC-LOK Mode (Model 3007A only) ············································ 18 operated in strict accordance with the instructions. KYORITSU will not
7-2 AUTO NULL ···················································································· 18 accept any liability for any damage or injury caused by misuse or non-
7-3 Back Light (Model 3007A only) ························································ 18 compliance with the instructions or safety procedures.
7-4 Auto Power Off ················································································ 18 ● It is essential to understand the safety rules contained in the manual.
8. BATTERY & FUSE REPLACEMENT ···················································· 19 They must be observed on using the instrument.
8-1 Battery Replacement ······································································ 19 Be sure to observe the above rules strictly. Not following the
8-2 Fuse Replacement ·········································································· 19 instructions may cause injury or instrument damage.
9. CASE AND STRAP BELT ASSEMBLY·················································· 20
10. CLEANING OF THE INSTRUMENT ····················································· 21 ○ The symbol on the instrument means that the user must refer to the
11. SERVICING···························································································· 21 relevant section of this manual for safe operation of the instrument. There
are three kinds of the symbol . Read the following instructions of each
symbol carefully.
―1―
3007A-E 01.9.12 11:52 AM ページ目1
CONTENTS 1. SAFTY PRECAUTIONS

1. SAFETY PRECAUTIONS ······································································· 1 ○ The instrument is designed to produce in accordance with the following
2. FEATURES ···························································································· 4 standards and supplied in the best conditions after successfully clearing
3. SPECIFICATIONS ················································································· 5 the inspection.
4. INSTRUMENT LAYOUT ········································································· 9
4-1 Instrument layout ············································································· 9 ・IEC 61010-1 Overvoltage CAT III 300V Pollution Degree 2
4-2 LCD ································································································ 10 ・IEC 61010-2-31 (Safety requirements for hand-held probe assemblies)
4-3 Connector ······················································································· 11
5. PREPARATION FOR MEASUREMENT ··············································· 12 This instruction manual describes warnings and safety rules which must be
5-1 Removing the Cover ······································································· 12 observed by the user to ensure safety operation of the instrument and to
5-2 Battery Voltage Check ····································································· 12 retain it in safe condition. Therefore, read through these instructions before
5-3 Test Probe Connection ··································································· 12 using the instrument.
6. OPERATION ·························································································· 13
6-1 Disconnection and Check of Power Source of WARNING
the Circuit under Test ····································································· 13 ● Read through and understand instructions contained in this manual
6-2 Insulation Resistance Measurement ··············································· 14 before using the instrument.
6-3 Continuity Measurement (Resistance Tests) ·································· 16 ● Save and keep the manual handy to enable quick reference whenever
6-4 Continuous Measurement ······························································· 17 necessary.
7. FUNCTIONS ·························································································· 18 ● The instrument must only be used by a competent trained person and
7-1 TRAC-LOK Mode (Model 3007A only) ············································ 18 operated in strict accordance with the instructions. KYORITSU will not
7-2 AUTO NULL ···················································································· 18 accept any liability for any damage or injury caused by misuse or non-
7-3 Back Light (Model 3007A only) ························································ 18 compliance with the instructions or safety procedures.
7-4 Auto Power Off ················································································ 18 ● It is essential to understand the safety rules contained in the manual.
8. BATTERY & FUSE REPLACEMENT ···················································· 19 They must be observed on using the instrument.
8-1 Battery Replacement ······································································ 19 Be sure to observe the above rules strictly. Not following the
8-2 Fuse Replacement ·········································································· 19 instructions may cause injury or instrument damage.
9. CASE AND STRAP BELT ASSEMBLY·················································· 20
10. CLEANING OF THE INSTRUMENT ····················································· 21 ○ The symbol on the instrument means that the user must refer to the
11. SERVICING···························································································· 21 relevant section of this manual for safe operation of the instrument. There
are three kinds of the symbol . Read the following instructions of each
symbol carefully.
―1―
3007A-E 01.9.12 11:52 AM ページ 2
DANGER is reserved for conditions and actions that are likely to cause CAUTION
serious or fatal injury. ● Always make sure to set the function switch or range selector switch to
WARNING is reserved for conditions and actions that can cause the appropriate position before taking measurements.
serious or fatal injury. ● Do not expose the instrument to the direct sun, dew fall or extreme
CAUTION is reserved for conditions and actions that can cause minor temperature and/or humidity.
injury or instrument damage. ● When the instrument will not be in use for a long period of time, place it
in storage after removing batteries.
DANGER ● Use a damp cloth soaked in water or neutral detergent for cleaning the
● Do not use this instrument on energized (LIVE) circuits. instrument. Do not use abrasives or solvents.
● Do not take measurement in the presence of flammable gasses.
Otherwise, the use of the instrument may cause sparkling, which leads
to an explosion.
● Always keep your fingers behind the barrier on test probe during
measurement.
● Never use the instrument if its surface or your hand is wet.
● Never open the battery compartment cover while taking measurement.
WARNING
● Do not attempt to take any measurements, if any abnormal conditions
occur, such as broken test probe and cracked enclosure of the
instrument.
● Never change function switches with test probe connected to the
equipment under test.
● Do not install substitute parts, perform any unauthorized modification, or
disassemble the instrument. Return the instrument to Kyoritsu or your
distributor for service and repair so as to ensure the safety features are
maintained.
● Do not replace batteries when the surface of the instrument is wet.
● Make sure to disconnect the test probe from the instrument before
opening the battery compartment cover for battery replacement.
―2― ―3―
3007A-E 01.9.12 11:52 AM ページ 2
DANGER is reserved for conditions and actions that are likely to cause CAUTION
serious or fatal injury. ● Always make sure to set the function switch or range selector switch to
WARNING is reserved for conditions and actions that can cause the appropriate position before taking measurements.
serious or fatal injury. ● Do not expose the instrument to the direct sun, dew fall or extreme
CAUTION is reserved for conditions and actions that can cause minor temperature and/or humidity.
injury or instrument damage. ● When the instrument will not be in use for a long period of time, place it
in storage after removing batteries.
DANGER ● Use a damp cloth soaked in water or neutral detergent for cleaning the
● Do not use this instrument on energized (LIVE) circuits. instrument. Do not use abrasives or solvents.
● Do not take measurement in the presence of flammable gasses.
Otherwise, the use of the instrument may cause sparkling, which leads
to an explosion.
● Always keep your fingers behind the barrier on test probe during
measurement.
● Never use the instrument if its surface or your hand is wet.
● Never open the battery compartment cover while taking measurement.
WARNING
● Do not attempt to take any measurements, if any abnormal conditions
occur, such as broken test probe and cracked enclosure of the
instrument.
● Never change function switches with test probe connected to the
equipment under test.
● Do not install substitute parts, perform any unauthorized modification, or
disassemble the instrument. Return the instrument to Kyoritsu or your
distributor for service and repair so as to ensure the safety features are
maintained.
● Do not replace batteries when the surface of the instrument is wet.
● Make sure to disconnect the test probe from the instrument before
opening the battery compartment cover for battery replacement.
―2― ―3―
3007A-E 01.9.12 11:52 AM ページ 4
2. FEATURES 3. SPECIFICATIONS
MODEL-3005A/3007A are microprocessor controlled insulation-continuity ● Measuring Range and Accuracy (at 23±5°C, relative humidity 45 -75%)
testers.
○ Insulation Resistance Ranges:
● Designed to safety standards: Nominal Output Voltage 250V 500V 1000V
IEC 61010-1 Overvoltage CAT III 300V Pollution Degree 2 0 ~19.99MΩ 0 ~19.99MΩ 0 ~19.99MΩ
Measuring
IEC 61010-2-31 (Safety requirements for hand-held probe assemblies) 0 ~ 199.9MΩ 0 ~ 199.9MΩ 0 ~ 199.9MΩ
Ranges
0 ~ 1999MΩ 0 ~ 1999MΩ 0 ~ 1999MΩ
● Display with back light function to facilitate work at night or dimly lit Open-Circuit 250V DC 500V DC 1000V DC
locations (Model 3007A only) Voltage +20%,-0% +20%,-0% +20%,-0%
1mA DC min. 1mA DC min. 1mA DC min.
Nominal Current
● Bar graph to indicate measured results at 0.25MΩ at 0.5MΩ at 1MΩ
Short-Circuit
1.5mA approx
● Strap belt to make both hands' operation easier Current
20MΩ
±1.5%rdg ±5dgt
● Live circuit warning indication and buzzer 200MΩ
Accuracy
2000 0~1GΩ ±3%rdg ±3dgt
MΩ 1G~2GΩ ±10%rdg ±3dgt
● Auto discharge function
When insulation resistance is measured, electric charges stored in
capacitive circuits are automatically discharged after testing. Discharge ○ Continuity Ranges:
can be checked with live circuit warning. Ranges 20Ω 200Ω 2000Ω
Measuring Ranges 0 ~ 19.99Ω 0 ~ 199.9Ω 0 ~ 1999Ω
● Auto power off function Open-Circuit
7 ~ 12V approx
To prevent the instrument from being left powered on and conserve Voltage
battery power, the instrument automatically turns off approx. 10 minutes Measuring Current
200mA min
after the last switch operation. at 0.2Ω ~ 2Ω
Accuracy ±1.5%rdg ±5dgt ±1.5%rdg ±3dgt
● LOK mode (Model 3007A only)
The test current is removed once a stable reading is reached to prevent ○ AC Voltage Indication
unnecessary battery consumption. 0 ~ 600V ±5%rdg ±3dgt
―4― ―5―
3007A-E 01.9.12 11:52 AM ページ 4
2. FEATURES 3. SPECIFICATIONS
MODEL-3005A/3007A are microprocessor controlled insulation-continuity ● Measuring Range and Accuracy (at 23±5°C, relative humidity 45 -75%)
testers.
○ Insulation Resistance Ranges:
● Designed to safety standards: Nominal Output Voltage 250V 500V 1000V
IEC 61010-1 Overvoltage CAT III 300V Pollution Degree 2 0 ~19.99MΩ 0 ~19.99MΩ 0 ~19.99MΩ
Measuring
IEC 61010-2-31 (Safety requirements for hand-held probe assemblies) 0 ~ 199.9MΩ 0 ~ 199.9MΩ 0 ~ 199.9MΩ
Ranges
0 ~ 1999MΩ 0 ~ 1999MΩ 0 ~ 1999MΩ
● Display with back light function to facilitate work at night or dimly lit Open-Circuit 250V DC 500V DC 1000V DC
locations (Model 3007A only) Voltage +20%,-0% +20%,-0% +20%,-0%
1mA DC min. 1mA DC min. 1mA DC min.
Nominal Current
● Bar graph to indicate measured results at 0.25MΩ at 0.5MΩ at 1MΩ
Short-Circuit
1.5mA approx
● Strap belt to make both hands' operation easier Current
20MΩ
±1.5%rdg ±5dgt
● Live circuit warning indication and buzzer 200MΩ
Accuracy
2000 0~1GΩ ±3%rdg ±3dgt
MΩ 1G~2GΩ ±10%rdg ±3dgt
● Auto discharge function
When insulation resistance is measured, electric charges stored in
capacitive circuits are automatically discharged after testing. Discharge ○ Continuity Ranges:
can be checked with live circuit warning. Ranges 20Ω 200Ω 2000Ω
Measuring Ranges 0 ~ 19.99Ω 0 ~ 199.9Ω 0 ~ 1999Ω
● Auto power off function Open-Circuit
7 ~ 12V approx
To prevent the instrument from being left powered on and conserve Voltage
battery power, the instrument automatically turns off approx. 10 minutes Measuring Current
200mA min
after the last switch operation. at 0.2Ω ~ 2Ω
Accuracy ±1.5%rdg ±5dgt ±1.5%rdg ±3dgt
● LOK mode (Model 3007A only)
The test current is removed once a stable reading is reached to prevent ○ AC Voltage Indication
unnecessary battery consumption. 0 ~ 600V ±5%rdg ±3dgt
―4― ―5―
3007A-E 01.9.12 11:52 AM ページ 6
● Typical Number of Measurements. IEC 60529 (IP54) Dust & drip proof
(central tendency for supply voltage up to 8V) ● Operating System: Dual integration
Insulation Resistance Ranges:
Approx. 1000 times min. at load 0.5MΩ ● Display: Liquid crystal display (maximum count: 1999),
Continuity Ranges: Unit, Mark
Approx. 700 times min. at load 1Ω Bar graph 30 points max. (20 points on Ω
range)
● Operating Errors (IEC 61557-2,-4)
Measuring range to keep Maximum percentage ● Over range Indication: "OL" is shown on the display.
Functions Range
operating error operating error
20MΩ 0.50 ~ 19.99MΩ ● Sample Rate: Approx. 0.5 ~ 2.5 times per second
1000V 200MΩ 1.0 ~ 199.9MΩ
2000MΩ 10 ~ 1000MΩ ● Operating Temperature 0 ~ +40°C, relative humidity up to 85%
20MΩ 0.50 ~ 19.99MΩ & Humidity:
500V 200MΩ 1.0 ~ 199.9MΩ
2000MΩ 10 ~ 100MΩ ● Storage Temperature -20 ~ +60°C, relative humidity up to 75%
20MΩ 0.25 ~ 19.99MΩ ±30% & Humidity:
250V 200MΩ 1.0 ~ 199.9MΩ
2000MΩ 10 ~ 100MΩ ● Insulation Resistance: More than 50MΩ at 1000V DC between electrical
20Ω 0.20 ~ 19.99Ω circuit and housing case
Ω 200Ω 1.0 ~ 199.9Ω
2000Ω 10 ~ 1999Ω ● Withstand Voltage: 3700V AC for one minute between electrical
The influencing variations used for calculating the operating error are circuit and housing case
denoted as follows;
Temperature: 0℃ and 35℃ ● Overload Protection
Supply voltage : 8V to 13.8V Insulation resistance ranges:
1000V Range 1200V (DC+AC p-p) for 10 seconds
● Applicable Standards 500V Range 600V (DC+AC p-p) for 10 seconds
IEC 61010-1 Over voltage CAT III 300V Pollution Degree 2 250V Range 300V (DC+AC p-p) for 10 seconds
IEC 61010-2-31 Safety requirements for hand-held probe Continuity ranges:
assemblies 20/200/2000Ω 280V (DC+AC p-p) for 10 seconds
IEC 61557-1/2/4 Measuring equipment for low voltage Range (Protection by fusing)
distribution systems
IEC 61326-1 EMC
―6― ―7―
3007A-E 01.9.12 11:52 AM ページ 6
● Typical Number of Measurements. IEC 60529 (IP54) Dust & drip proof
(central tendency for supply voltage up to 8V) ● Operating System: Dual integration
Insulation Resistance Ranges:
Approx. 1000 times min. at load 0.5MΩ ● Display: Liquid crystal display (maximum count: 1999),
Continuity Ranges: Unit, Mark
Approx. 700 times min. at load 1Ω Bar graph 30 points max. (20 points on Ω
range)
● Operating Errors (IEC 61557-2,-4)
Measuring range to keep Maximum percentage ● Over range Indication: "OL" is shown on the display.
Functions Range
operating error operating error
20MΩ 0.50 ~ 19.99MΩ ● Sample Rate: Approx. 0.5 ~ 2.5 times per second
1000V 200MΩ 1.0 ~ 199.9MΩ
2000MΩ 10 ~ 1000MΩ ● Operating Temperature 0 ~ +40°C, relative humidity up to 85%
20MΩ 0.50 ~ 19.99MΩ & Humidity:
500V 200MΩ 1.0 ~ 199.9MΩ
2000MΩ 10 ~ 100MΩ ● Storage Temperature -20 ~ +60°C, relative humidity up to 75%
20MΩ 0.25 ~ 19.99MΩ ±30% & Humidity:
250V 200MΩ 1.0 ~ 199.9MΩ
2000MΩ 10 ~ 100MΩ ● Insulation Resistance: More than 50MΩ at 1000V DC between electrical
20Ω 0.20 ~ 19.99Ω circuit and housing case
Ω 200Ω 1.0 ~ 199.9Ω
2000Ω 10 ~ 1999Ω ● Withstand Voltage: 3700V AC for one minute between electrical
The influencing variations used for calculating the operating error are circuit and housing case
denoted as follows;
Temperature: 0℃ and 35℃ ● Overload Protection
Supply voltage : 8V to 13.8V Insulation resistance ranges:
1000V Range 1200V (DC+AC p-p) for 10 seconds
● Applicable Standards 500V Range 600V (DC+AC p-p) for 10 seconds
IEC 61010-1 Over voltage CAT III 300V Pollution Degree 2 250V Range 300V (DC+AC p-p) for 10 seconds
IEC 61010-2-31 Safety requirements for hand-held probe Continuity ranges:
assemblies 20/200/2000Ω 280V (DC+AC p-p) for 10 seconds
IEC 61557-1/2/4 Measuring equipment for low voltage Range (Protection by fusing)
distribution systems
IEC 61326-1 EMC
―6― ―7―
3007A-E 01.9.12 11:52 AM ページ 8
● Dimensions: 185(L) x 167(W) x 89(D) mm approx. 4. INSTRUMENT LAYOUT

● Weight: 990g approx. (including batteries) 4-1 INSTRUMENT LAYOUT
⑩
● Power Source: 8 x R6P, 1.5V AA or equivalent
⑤
● Auto-power-off Function: Automatically turns off approx. 10 minutes after ①
⑪
the last switch operation.
Consumption current: approx. 75µA
● Accessories ②
Test Probe MODEL7122 x 1 set ⑥
Strap belt x1
Test probe pouch x1 ③
Batteries (R6P) x8 ⑧ ⑨
Instruction manual x1
④
Spare fuse F600V/500mA x1
①… LCD DISPLAY
②… TRAC-LOKSWITCH (Model 3007A only)
③… RANGE SELECTOR SWITCH
④… TEST BUTTON
⑤… CONNECTOR
⑥… BACK LIGHT SWITCH (Model 3007A only)
⑦… FUNCTION SWITCH
⑧… TEST PROBE (RED)
⑨… TEST PROBE (BLACK)
⑩… ALLIGATOR CLIP (BLACK)
⑪… PLOBE CAP (BLACK & RED)
―8― ―9―
3007A-E 01.9.12 11:52 AM ページ 8
● Dimensions: 185(L) x 167(W) x 89(D) mm approx. 4. INSTRUMENT LAYOUT

● Weight: 990g approx. (including batteries) 4-1 INSTRUMENT LAYOUT
⑩
● Power Source: 8 x R6P, 1.5V AA or equivalent
⑤
● Auto-power-off Function: Automatically turns off approx. 10 minutes after ①
⑪
the last switch operation.
Consumption current: approx. 75µA
● Accessories ②
Test Probe MODEL7122 x 1 set ⑥
Strap belt x1
Test probe pouch x1 ③
Batteries (R6P) x8 ⑧ ⑨
Instruction manual x1
④
Spare fuse F600V/500mA x1
①… LCD DISPLAY
②… TRAC-LOKSWITCH (Model 3007A only)
③… RANGE SELECTOR SWITCH
④… TEST BUTTON
⑤… CONNECTOR
⑥… BACK LIGHT SWITCH (Model 3007A only)
⑦… FUNCTION SWITCH
⑧… TEST PROBE (RED)
⑨… TEST PROBE (BLACK)
⑩… ALLIGATOR CLIP (BLACK)
⑪… PLOBE CAP (BLACK & RED)
―8― ―9―
3007A-E 01.9.12 11:52 AM ページ 10
4-2 LCD DISPLAY 10…OUTPUT VOLTAGE GRAPH (INSULATION RESISTANCE)

2 1 3
FUNCTION SETTING
4 11 PER RATED OUTPUT VOLTAGE
1 ~ 24%
25 ~ 49%
5
50 ~ 74%
6 10 75 ~ 99%
100% or over
7
8 12 9
11… OUTPUT VOLTAGE RANGE
1… INSULATION RESISTANCE SCALE 12… MEASUREMENT VALUES
2… BAR GRAPH
3… CONTINUITY SCALE 4-3 Connector
4… LIVE CIRCUIT WARNING
AC LIVE CIRCUIT DISCHARGE VOLTAGE
WARNING
0∼2V 0∼2V
3∼30V 3∼60V
31∼60V 61∼120V
61∼120V 121∼240V
120V over 240V over
5… TRACK/LOK MODE
6… AUTONULL OPERATION
7… BATTERY VOLTAGE WARNING
8… CONTINUITY/INSULAATION RESISTANCE RANGE SETTING
9… UNIT
― 10 ― ― 11 ―
3007A-E 01.9.12 11:52 AM ページ 10
4-2 LCD DISPLAY 10…OUTPUT VOLTAGE GRAPH (INSULATION RESISTANCE)

2 1 3
FUNCTION SETTING
4 11 PER RATED OUTPUT VOLTAGE
1 ~ 24%
25 ~ 49%
5
50 ~ 74%
6 10 75 ~ 99%
100% or over
7
8 12 9
11… OUTPUT VOLTAGE RANGE
1… INSULATION RESISTANCE SCALE 12… MEASUREMENT VALUES
2… BAR GRAPH
3… CONTINUITY SCALE 4-3 Connector
4… LIVE CIRCUIT WARNING
AC LIVE CIRCUIT DISCHARGE VOLTAGE
WARNING
0∼2V 0∼2V
3∼30V 3∼60V
31∼60V 61∼120V
61∼120V 121∼240V
120V over 240V over
5… TRACK/LOK MODE
6… AUTONULL OPERATION
7… BATTERY VOLTAGE WARNING
8… CONTINUITY/INSULAATION RESISTANCE RANGE SETTING
9… UNIT
― 10 ― ― 11 ―
3007A-E 01.9.12 11:52 AM ページ 12
5. PREPARATION FOR MEASUREMENT 6. OPERATION

5-1 Removing the Cover 6-1 Disconnection and check of power source of the circuit under test
Model 3005A/3007A have a dedicated cover to protect against an impact
from the outside and prevent the operation part, LCD, and connector DANGER
socket from becoming dirty. The cover can be detached and put on the ● To avoid possible electrical shock, do not perform measurements on
back side of the main body during measurement. energized (LIVE) circuits.
● Never make measurements with the battery compartment cover
Method of removing the cover Method of storing the cover removed.
CAUTION
● Never press the test button if the live circuit warning is indicated or the
warning buzzer sounds. This may damage the circuit.
Voltage check can be made with the function switch at any position except "OFF".
Be sure to turn off the breaker for the circuit under test.
① Connect the test probe (black) to the earth side and the test probe (red) to
the line side of the circuit under test.
② Ensure that the live circuit warning is not lit and the audible warning is not
5-2 Battery Voltage Check present. When the live circuit warning is lit and the buzzer sounds, never
① Set the function switch to any position except "OFF". press the test button. Voltage is generated in the circuit under test.
② When the battery voltage warning symbol ( ) is lit, the batteries are Recheck that the breaker for the circuit under test is "OFF".
exhausted. Replace all of them with new ones according to section 8
for battery & fuse replacement.
5-3 Test Probe Connection

Insert test probes fully into connector terminals of the instrument.
Connect test probe (black) to EARTH terminal and test probe (red) to
LINE terminal of connector terminal.
― 12 ― ― 13 ―
3007A-E 01.9.12 11:52 AM ページ 12
5. PREPARATION FOR MEASUREMENT 6. OPERATION

5-1 Removing the Cover 6-1 Disconnection and check of power source of the circuit under test
Model 3005A/3007A have a dedicated cover to protect against an impact
from the outside and prevent the operation part, LCD, and connector DANGER
socket from becoming dirty. The cover can be detached and put on the ● To avoid possible electrical shock, do not perform measurements on
back side of the main body during measurement. energized (LIVE) circuits.
● Never make measurements with the battery compartment cover
Method of removing the cover Method of storing the cover removed.
CAUTION
warning buzzer sounds. This may damage the circuit.
Voltage check can be made with the function switch at any position except "OFF".
Be sure to turn off the breaker for the circuit under test.
① Connect the test probe (black) to the earth side and the test probe (red) to
the line side of the circuit under test.
② Ensure that the live circuit warning is not lit and the audible warning is not
5-2 Battery Voltage Check present. When the live circuit warning is lit and the buzzer sounds, never
① Set the function switch to any position except "OFF". press the test button. Voltage is generated in the circuit under test.
② When the battery voltage warning symbol ( ) is lit, the batteries are Recheck that the breaker for the circuit under test is "OFF".
exhausted. Replace all of them with new ones according to section 8
for battery & fuse replacement.
5-3 Test Probe Connection

Insert test probes fully into connector terminals of the instrument.
Connect test probe (black) to EARTH terminal and test probe (red) to
LINE terminal of connector terminal.
― 12 ― ― 13 ―
3007A-E 01.9.12 11:52 AM ページ 14
6-2 Insulation Resistance Measurement ④ Read the resistance value from the LCD.
DANGER
● Always test the circuit or equipment to ensure it is surely de-energized
before measurement according to the instruction of 6-1.
● To avoid electrical shock, measurements must be performed on de-
energized circuits only.
● When the test button is pressed with the function switch in the MΩ
position, take care not to touch the tip of the test probe and the circuit
under test where a high voltage is present in order to avoid possible
shock hazard.
● Never make measurement with the battery compartment cover removed.
⑤ With the test probe still connected to the circuit under test, release the test
CAUTION button to discharge capacitance in the circuit after measurement.
warning buzzer sounds. This may damage the circuit. DANGER
●Conduct the voltage warning check before measurement to ensure that Do not touch the circuit under test immediately after testing. Capacitance
the circuit under test is de-energized. stored in the circuit may cause electric shock.
① Check the voltage which can be applied to the circuit under test and set Leave test probes connected to the circuit and never touch the circuit until
the function switch and the range selector switch to the desired range. the discharge is completed.
② Connect the test probe (black) to the earth terminal of the circuit under ●Principle of Insulation Resistance Measurement
test. Resistance value can be obtained by applying a certain high voltage to the
③ Put the tip of the test probe (red) to the circuit under test and press the resistance (insulation resistance) and measuring the flowing current.
test button.
The buzzer sounds intermittently during measurement. Resistance Value = Voltage / Current
RX = V / I
Current outputs from the earth terminal, and returns to the line terminal.
― 14 ― ― 15 ―
3007A-E 01.9.12 11:52 AM ページ 14
6-2 Insulation Resistance Measurement ④ Read the resistance value from the LCD.
DANGER
● When the test button is pressed with the function switch in the MΩ
position, take care not to touch the tip of the test probe and the circuit
under test where a high voltage is present in order to avoid possible
shock hazard.
● Never make measurement with the battery compartment cover removed.
⑤ With the test probe still connected to the circuit under test, release the test
CAUTION button to discharge capacitance in the circuit after measurement.
warning buzzer sounds. This may damage the circuit. DANGER
●Conduct the voltage warning check before measurement to ensure that Do not touch the circuit under test immediately after testing. Capacitance
the circuit under test is de-energized. stored in the circuit may cause electric shock.
① Check the voltage which can be applied to the circuit under test and set Leave test probes connected to the circuit and never touch the circuit until
the function switch and the range selector switch to the desired range. the discharge is completed.
② Connect the test probe (black) to the earth terminal of the circuit under ●Principle of Insulation Resistance Measurement
test. Resistance value can be obtained by applying a certain high voltage to the
③ Put the tip of the test probe (red) to the circuit under test and press the resistance (insulation resistance) and measuring the flowing current.
test button.
The buzzer sounds intermittently during measurement. Resistance Value = Voltage / Current
RX = V / I
Current outputs from the earth terminal, and returns to the line terminal.
― 14 ― ― 15 ―
3007A-E 01.9.12 11:52 AM ページ 16
●Terminal connection of insulation resistance test ● Principle of Continuity Measurement (Resistance Test)
In case of testing insulation of insulated wire and cable against the earth Resistance value can be obtained by applying a certain current to the
at direct current, connecting - pole of power to cable conductor, + to the resistance under test and measuring the voltage generated on the both
earth obtains smaller measuring value, compared with connecting the sides of the resistor under test.
other way round. This connecting method is generally acknowledged
relevant to detect defective insulation. Resistance value = Voltage / Current
RX = V / I
6-3 Continuity Measurement (Resistance Tests)
DANGER
● Never make measurement with the battery compartment cover
removed. 6-4 Continuous Measurement
A lock down feature is incorporated on the test button. Pressing and
CAUTION turning it clockwise, lock the test button in the continuous operating
● Never press the test button if the live circuit warning is indicated or the position.
warning buzzer sounds. This may damage the circuit. To release the lock, turn the test button counterclockwise.
● When an additional circuit is connected in parallel with the circuit under
test , inaccurate reading may be taken. NOTE:
① Set the function switch to the "AUTO NULL" position. Model 3007A has TRAC/LOK function. When "LOK" mode is selected,
② Short the test probes (red) and (black) and press the test button. Then the sampling is conducted only once, even though the test button is locked
resistance of the test probes is displayed and memorized with down for continuous measurement.
microprocessor. To make continuous measurement, select "TRAC" mode.
③ Set the function switch to "Ω" position.
④ Connect the test probes to the circuit under test and press the test button. DANGER
⑤ Read the resistance value from the LCD. Be extremely careful not to get electric shock during insulation resistance
measurement as high voltage is present on the tip of test probes
●NULL symbol ( ) is displayed while AUTO NULL function is working. continuously.
●AUTO NULL will be cancelled when the instrument is powered off.
― 16 ― ― 17 ―
3007A-E 01.9.12 11:52 AM ページ 16
●Terminal connection of insulation resistance test ● Principle of Continuity Measurement (Resistance Test)
In case of testing insulation of insulated wire and cable against the earth Resistance value can be obtained by applying a certain current to the
at direct current, connecting - pole of power to cable conductor, + to the resistance under test and measuring the voltage generated on the both
earth obtains smaller measuring value, compared with connecting the sides of the resistor under test.
other way round. This connecting method is generally acknowledged
relevant to detect defective insulation. Resistance value = Voltage / Current
RX = V / I
6-3 Continuity Measurement (Resistance Tests)
DANGER
● Never make measurement with the battery compartment cover
removed. 6-4 Continuous Measurement
A lock down feature is incorporated on the test button. Pressing and
CAUTION turning it clockwise, lock the test button in the continuous operating
● Never press the test button if the live circuit warning is indicated or the position.
warning buzzer sounds. This may damage the circuit. To release the lock, turn the test button counterclockwise.
● When an additional circuit is connected in parallel with the circuit under
test , inaccurate reading may be taken. NOTE:
① Set the function switch to the "AUTO NULL" position. Model 3007A has TRAC/LOK function. When "LOK" mode is selected,
② Short the test probes (red) and (black) and press the test button. Then the sampling is conducted only once, even though the test button is locked
resistance of the test probes is displayed and memorized with down for continuous measurement.
microprocessor. To make continuous measurement, select "TRAC" mode.
③ Set the function switch to "Ω" position.
④ Connect the test probes to the circuit under test and press the test button. DANGER
⑤ Read the resistance value from the LCD. Be extremely careful not to get electric shock during insulation resistance
measurement as high voltage is present on the tip of test probes
●NULL symbol ( ) is displayed while AUTO NULL function is working. continuously.
●AUTO NULL will be cancelled when the instrument is powered off.
― 16 ― ― 17 ―
3007A-E 01.9.12 11:52 AM ページ 18
7. FUNCTIONS 8. BATTERY & FUSE REPLACEMENT

7-1 TRAC-LOK MODE (Model 3007A)
TRAC mode : Measurement can be conducted while the test button is DANGER
being pressed. ● Never open the battery compartment cover while making measurement.
When making continuous measurement, select this mode. To avoid possible electrical shock, disconnect the test probe before
LOK mode : When the test button is pressed, measurement can be conducted opening the cover for battery and fuse replacement.
only once, and output is stopped, then automatically discharged. ● Replacement fuse must be have the following rating.
This allows to economize on the battery life. Fast acting type, F 500mA/600V, φ6.35×32mm
7-2 AUTO NULL

8-1 Battery Replacement
When conducting continuity tests, the contact resistance of test probes etc.
① Disconnect test probes from the instrument.
is automatically subtracted before the real resistance is displayed to obtain
② Open the battery compartment cover by unscrewing the metal captive
more accurate reading.
screw to reveal battery compartment. Always replace all eight
This function is invalid when the contact resistance, etc. is 10Ω or more.
batteries with new ones at the same time.
・ NULL symbol ( ) is displayed while AUTO NULL function is working.
Battery type: 8 x R6P, 1.5V AA or equivalent
・ AUTO NULL will be cancelled when the instrument is powered off.
7-3 BACK LIGHT (Model 3007A) 8-2 Fuse Replacement
Use BACK LIGHT to facilitate working at night or dimly lit situations. ① Disconnect the test probe from the instrument.
When the back light switch is pressed with the function switch in any ② Open the battery compartment cover by unscrewing the metal captive
position except "OFF", the back light continues illuminating for approx. 40 screw to reveal battery compartment and replace the fuse.
seconds and then turns off automatically. Fuse type: 600V/500mA (F) quick acting ceramic fuse 6.35 x 32mm
When the back light switch is pressed again, the BACK LIGHT will turn off
even within the lighting time.
Press the back light switch while it is on, the light gets brighter. Press it
again to turn it OFF.
7-4 AUTO-POWER-OFF
The instrument automatically turns off approx. 10 minutes after the last
switch operation. To return to the normal mode, turn the function switch CAUTION
off, then to the desired position.
Install batteries in correct
CAUTION polarity as marked inside.
Slight current is still consumed even after the instrument was powered off
by auto-power-off function. Turn the function switch to the "OFF" position
when not using the instrument.
― 18 ― ― 19 ―
3007A-E 01.9.12 11:52 AM ページ 18
7. FUNCTIONS 8. BATTERY & FUSE REPLACEMENT

7-1 TRAC-LOK MODE (Model 3007A)
TRAC mode : Measurement can be conducted while the test button is DANGER
being pressed. ● Never open the battery compartment cover while making measurement.
When making continuous measurement, select this mode. To avoid possible electrical shock, disconnect the test probe before
LOK mode : When the test button is pressed, measurement can be conducted opening the cover for battery and fuse replacement.
only once, and output is stopped, then automatically discharged. ● Replacement fuse must be have the following rating.
This allows to economize on the battery life. Fast acting type, F 500mA/600V, φ6.35×32mm
7-2 AUTO NULL

8-1 Battery Replacement
When conducting continuity tests, the contact resistance of test probes etc.
① Disconnect test probes from the instrument.
is automatically subtracted before the real resistance is displayed to obtain
② Open the battery compartment cover by unscrewing the metal captive
more accurate reading.
screw to reveal battery compartment. Always replace all eight
This function is invalid when the contact resistance, etc. is 10Ω or more.
batteries with new ones at the same time.
・ NULL symbol ( ) is displayed while AUTO NULL function is working.
Battery type: 8 x R6P, 1.5V AA or equivalent
・ AUTO NULL will be cancelled when the instrument is powered off.
7-3 BACK LIGHT (Model 3007A) 8-2 Fuse Replacement
Use BACK LIGHT to facilitate working at night or dimly lit situations. ① Disconnect the test probe from the instrument.
When the back light switch is pressed with the function switch in any ② Open the battery compartment cover by unscrewing the metal captive
position except "OFF", the back light continues illuminating for approx. 40 screw to reveal battery compartment and replace the fuse.
seconds and then turns off automatically. Fuse type: 600V/500mA (F) quick acting ceramic fuse 6.35 x 32mm
When the back light switch is pressed again, the BACK LIGHT will turn off
even within the lighting time.
Press the back light switch while it is on, the light gets brighter. Press it
again to turn it OFF.
7-4 AUTO-POWER-OFF
The instrument automatically turns off approx. 10 minutes after the last
switch operation. To return to the normal mode, turn the function switch CAUTION
off, then to the desired position.
Install batteries in correct
CAUTION polarity as marked inside.
Slight current is still consumed even after the instrument was powered off
by auto-power-off function. Turn the function switch to the "OFF" position
when not using the instrument.
― 18 ― ― 19 ―
3007A-E 01.9.12 11:52 AM ページ 20
9. CASE AND STRAP BELT ASSEMBLY 10. CLEANING OF THE INSTRUMENT

By hanging the instrument around the neck, both hands can be used freely ● When cleaning the instrument, wipe it with a silicon cloth or soft cloth to
for easy and safety working. remove dust or dirt.
● When it is hard to remove the dirt, wipe it with a cloth wet with water and
dry the instrument completely after cleaning.
CAUTION
Never use any solvent which may transmute plastics, for example, organic
solvent such as benzene, acetone, etc.
11. SERVICING
If this tester should fail to operate correctly, return it to your nearest

Pass the strap belt down through distributors stating the exact nature of the fault.
the side panel of the main body Before returning the instrument, make sure that:
from the top, and up through the a) Operating instructions have been followed.
slots of the probe case from the b) Leads have been inspected.
bottom. c) Fuse has been checked.
d) Battery has been checked.
e) The unit is returned with all accessory leads.
Remember, the more information written about the fault, the quicker it will be
Pass the strap through the buckle, serviced.
adjust the strap for length and
secure.
― 20 ― ― 21 ―
3007A-E 01.9.12 11:52 AM ページ 20
9. CASE AND STRAP BELT ASSEMBLY 10. CLEANING OF THE INSTRUMENT

By hanging the instrument around the neck, both hands can be used freely ● When cleaning the instrument, wipe it with a silicon cloth or soft cloth to
for easy and safety working. remove dust or dirt.
● When it is hard to remove the dirt, wipe it with a cloth wet with water and
dry the instrument completely after cleaning.
CAUTION
Never use any solvent which may transmute plastics, for example, organic
solvent such as benzene, acetone, etc.
11. SERVICING
If this tester should fail to operate correctly, return it to your nearest

Pass the strap belt down through distributors stating the exact nature of the fault.
the side panel of the main body Before returning the instrument, make sure that:
from the top, and up through the a) Operating instructions have been followed.
slots of the probe case from the b) Leads have been inspected.
bottom. c) Fuse has been checked.
d) Battery has been checked.
e) The unit is returned with all accessory leads.
Remember, the more information written about the fault, the quicker it will be
Pass the strap through the buckle, serviced.
adjust the strap for length and
secure.
― 20 ― ― 21 ―
3007A-E 01.9.12 11:52 AM ページ表4
DISTRIBUTOR INSTRUCTION MANUAL
Kyoritsu reserves the rights to change specifications or designs

described in this manual without notice and without obligations.
KYORITSU ELECTRICAL
INSTRUMENTS DIGITAL INSULATION-CONTINUITY TESTER
WORKS, LTD.
No.5-20,Nakane 2-chome, Meguro-ku, Tokyo
152-0031 Japan
MODEL 3005A /3007A
Phone :(03) 3723-0131 Fax : (03) 3723-0152
URL : http://www.kew-ltd.co.jp
E-mail : [email protected] KYORITSU ELECTRICAL INSTRUMENTS
Factories : Uwajima & Ehime WORKS, LTD.
01-09 92-1492A

MODEL 3005A /3007A: Instruction Manual

Uploaded by

Copyright:

Available Formats

MODEL 3005A /3007A: Instruction Manual

Uploaded by

Document Information

Original Title

Copyright

Available Formats

Share this document

Share or Embed Document

Sharing Options

Did you find this document useful?

Is this content inappropriate?

Copyright:

Available Formats

MODEL 3005A /3007A: Instruction Manual

Uploaded by

Copyright:

Available Formats

3007A-E 01.9.

DISTRIBUTOR INSTRUCTION MANUAL

Kyoritsu reserves the rights to change specifications or designs

CONTENTS 1. SAFTY PRECAUTIONS

CONTENTS 1. SAFTY PRECAUTIONS

● Dimensions: 185(L) x 167(W) x 89(D) mm approx. 4. INSTRUMENT LAYOUT

● Dimensions: 185(L) x 167(W) x 89(D) mm approx. 4. INSTRUMENT LAYOUT

4-2 LCD DISPLAY 10…OUTPUT VOLTAGE GRAPH (INSULATION RESISTANCE)

4-2 LCD DISPLAY 10…OUTPUT VOLTAGE GRAPH (INSULATION RESISTANCE)

5. PREPARATION FOR MEASUREMENT 6. OPERATION

5-3 Test Probe Connection

5. PREPARATION FOR MEASUREMENT 6. OPERATION

5-3 Test Probe Connection

7. FUNCTIONS 8. BATTERY & FUSE REPLACEMENT

7-2 AUTO NULL

7. FUNCTIONS 8. BATTERY & FUSE REPLACEMENT

7-2 AUTO NULL

9. CASE AND STRAP BELT ASSEMBLY 10. CLEANING OF THE INSTRUMENT

If this tester should fail to operate correctly, return it to your nearest

9. CASE AND STRAP BELT ASSEMBLY 10. CLEANING OF THE INSTRUMENT

If this tester should fail to operate correctly, return it to your nearest

DISTRIBUTOR INSTRUCTION MANUAL

Kyoritsu reserves the rights to change specifications or designs

You might also like