ISSN 2394-3777 (Print)
ISSN 2394-3785 (Online)
Available online at www.ijartet.com
International Journal of Advanced Research Trends in Engineering and Technology (IJARTET)
Vol. 7, Issue 7, July 2020
Wireless Notice Board with Wide Range
Communication
Dr.Parthiban K.G,
HoD\Electrical Sciences
Abishek R, Pradeesh S,Kaviarasan K
Final Year \ECE Students
Department of Electronics and Communication Engineering
Adithya Institute of Technology
Abstract: Our project proposal is to design a low cost and high efficiency wireless notice board. Wireless electronics notice
boards are a faster alternative to other notice boards (GSM based and low range communicating systems.The proposed
system uses Bluetooth and Wi-Fi based wireless serial data communication using programmed (esp32 devkit v1)
microcontroller for transmitting user data.At receiver end a low cost microcontroller board (ATMega328P) is programmed
to receive and display any above information from the transmitting side (through user). A major constraint of this method
used so far is of small size display board. We use advanced larger display board with low power consumption with reduced
data transmission time from sender /user to the receiver end display. The developed system will therefore aim in wirelessly
sharing the information through Bluetooth and displaying in a notice board.
Key words: ESP32 DVE module, ATMega328P, HC-12 SI4463, Arduino IDE, OLED display
I. INTRODUCTION are in the local or in wide area network. So this document
In today’s world of connectedness, people are gives us better idea how to change the contents of Digital
becoming accustomed to easy access to information. display using Wi-Fi and Bluetooth.
Whether it’s through the internet or television, people So for that we use some Embedded as well as
want to be informed and up-to-date with the latest events communication idea and using ESP32devkit v1 board and
happening around the world (J. S. Lee 2007). Wired HC-12 Bluetooth module we try to implement our system.
network connection such as Ethernet has many limitations The OLED used as to 16-bit level the information are to
depending on the need and type of connection. Now a be displayed.it specifies the characters and to display it
day’s people prefer wireless connection because they can whenever type to show the text in to the user language.
interact with people easily and it require less time. The All major urban areas are currently covered by both WI-FI
main objective of this project is to develop a wireless network providers, and soon every single corner of the
notice board that display message sent from the user and peoples has used in mobiles in a very poor villages to call
to design a simple, easy to install, user friendly system, away. The method to need for constant communication
which can receive and display notice in a particular with family and friends, coupled with the relatively cheap
manner with respect to date and time which will help the method of sending short text messages to them, has
user to easily keep the track of notice board every day and information a WI-FI revolution in the country. In fact,
each time he uses the system. Wi-Fi is the wireless rarely will a used this method use his cell phone to make a
technology used and also using a Bluetooth technology. phone call, Preferring to anything and everything. All
This Document gives basic introduction to Digital mobile phones has available in WI-FI network. Then WI-
signage which can operate using Wi-Fi and Bluetooth. FI network has been used to provide wide area network
Now a day we have very less option for advertising and it allows as to communicate with the information into text
is very lengthy and boring process to advertise and also message through OLED display to move the notice board.
we have very less efficiency of that. So we have one good Information can passing through for a specific service
option to reach over a people is Digital signage system. provide as chatting and to transmit and receive the
Recently we have a digital signage but we have to change information.
its content using USB drives or using internet when we
All Rights Reserved © 2020 IJARTET 96
ISSN 2394-3777 (Print)
ISSN 2394-3785 (Online)
Available online at www.ijartet.com
International Journal of Advanced Research Trends in Engineering and Technology (IJARTET)
Vol. 7, Issue 7, July 2020
II. EXISTING SYSTEM IV. PROPOSED SYSTEM
The simple and low-cost wireless android based Our project proposal is to design a low cost and high
notice board system is developed to remotely send the efficiency wireless notice board. wireless electronics
desired information instantly to the intended users using notice boards are a faster alternative to other notice boards
either Bluetooth or Wi-Fi transceiver modules interfaced (GSM based and low range communicating systems) .the
with a low cost Arduino UNO microcontroller board. proposed system uses Bluetooth and Wi-Fi based wireless
serial data communication using programmed (esp32
devkitv1) microcontroller for transmitting user data .at
receiver end a low cost microcontroller board
(ATMega328P) is programmed toreceive and display in
any above of the communication mode.
ADVANTAGES:
High efficiency data transmission through the
transmitter and receiver
The data will be send long range of distance
through serial communication Wi-Fi module
Power consumption in dc characteristics is too
low
As the project prototype can be operated in both
AC and DC power supply
Figure: Existing System
METHODOLOGY:
DISADVANTAGES:
We are using IoT and long range data processing
Short Range communication
technique
Ac power consumption is high
The main component used here is esp32 devkit
Transmission bitrate is too low v1
Using an LCD screen The Wi-Fi and Bluetoothtechnique to reduce man
power and time.
III. LITERATURE SURVEY Interfaced with a low cost Arduino UNO
Vinod B.Jadhav, Tejas S.Nagwanshi, Yogesh P.Patil, microcontroller board.
Deepak R, Patil (2016) had propose a remotely send
notice to digital monitor from authorized pc on raspberry V. BLOCK DIAGRAM
pi card .A Wi-Fi is using for data transmission. Wireless
is a popular technology that allows an electronic device to
exchange data wirelessly over a computer network
S.Arulmurugan, S.Anith, A.Priyanga,
S.Sangeethapriya At (2016)-notice board is commonly
used in variety of institution which we come across in a
daily basis.In the present generation the advertisement
notice board are being manually. This process is difficult
to involve in order putting a notice on the notice board
Duruchinedu, Ochonu Regina, Okoronkwo
C.Onyinye (2017)-design and implementation of a
wireless notice board with interface for remote update, a
mobile phone controlled wireless notice board operation
system by sending an SMS(short message service) to a
system which display the received SMS on a screen for
public viewing Figure: Wireless Notice Board
All Rights Reserved © 2020 IJARTET 97
ISSN 2394-3777 (Print)
ISSN 2394-3785 (Online)
Available online at www.ijartet.com
International Journal of Advanced Research Trends in Engineering and Technology (IJARTET)
Vol. 7, Issue 7, July 2020
VI. HARDWARE
ESP32 module is a highly-integrated solution for
Wi-Fi-and-Bluetooth IoT applications, with around 20
external components. ESP32 integrates an antenna switch,
RF balun, power amplifier, low-noise receive amplifier,
filters, and power management modules. As such, the
Figure: 0.91inch OLED Display
entire solution occupies minimal Printed Circuit Board
7.4 ATMEGA328P MICROCONTROLLER:
(PCB) area
ATMEGA328P is High Performance, Low Power
HC-12-Wireless Transceiver Module- SI4463:
Controller from Microchip. ATMEGA328P is an 8-bit
Microcontroller Based on AVR RISC Architecture.It is
the Most Popular of All AVR Controllers as it is used in
Arduino Boards. Arduino is used for Building Different
Types of Electronic Circuits Easily Using of Both a
Physical Programmable Circuit Board Usually
Microcontroller and Piece of Code Running on Computer
with USB Connection between the Computer and
Arduino.Programming Language Used in Arduino is Just
a Simplified Version of C++ that Can Easily Replace
Figure: Hc-12-Wireless Thousands of Wires with Words.
This module offers a wireless data transmission and
reception range of approximately 1.8 Km in open air. It's
a low power radio chip which is ultra-easy to use. This
module has an onboard STM8S003F3P6 MCU which is
communicating with the SI4463. So that the user can
communicate with the module using a simple TTL 2 wire
serial interface (RX, TX, and GND).
7.3 0.91INCH OLED DISPLAY:
This is a 0.91 inch blue OLED display module. The
display module can be interfaced with any microcontroller
using SPI/IIC protocols. It is having a resolution of Figure: Arduino Uno R3 Boards
128x32.The package includes display board, display, 4 8. RESULT AND DISCUSSIONS:
pin male header pre-soldered to board.OLED (Organic
Light-Emitting Diode) is a self-light-emitting technology
composed of a thin, multi-layered organic film placed
between an anode and cathode. In contrast to LCD
technology, OLED does not require a backlight. OLED
possesses high application potential for virtually all types
of displays and is regarded as the ultimate technology for
the next generation of flat-panel displays. OLEDs basic
structure consists of organic materials positioned between
the Cathode and the anode, which is composed of electric
conductive transparent Indium Tin Oxide (ITO).The
organic materials compose a multi-layered thin film, Figure: Transmitter mobile application
which includes the Hole Transporting Layer (HTL), Result 1:
Emission Layer (EML) and the Electron Transporting const char* ssid = “Samsung j5 2016";
Layer (ETL). const char* password = “kaviarasan";
How are you
Result 2:
All Rights Reserved © 2020 IJARTET 98
ISSN 2394-3777 (Print)
ISSN 2394-3785 (Online)
Available online at www.ijartet.com
International Journal of Advanced Research Trends in Engineering and Technology (IJARTET)
Vol. 7, Issue 7, July 2020
Figure:Receiver Window
incomingByte = HC12.read(); Figure: Arduino IDE Window
How are you VIII. USE CASE DIAGRAM
VII. SOFTWARE SETTINGS
Introduction to Arduino IDE
IDE stands for “Integrated Development
Environment”. It is an official software introduced by
Arduino. That is mainly used for editing, compiling and
uploading the code in the Arduino Device. Almost all
Arduino modules are compatible with this software that is
an open source and is readily available to install and start
compiling the code on the go. The IDE environment is
Figure: Use Case Diagram
mainly distributed into three sections 1. Menu Bar 2. Text
IX. CONCLUSION
Editor 3. Output Pane bar appearing on the top is called
Wireless operations permit services, such as long-
Menu Bar that comes with five different options as follow
range communications, implement with the use of
File – You can open a new window for writing the code
wireless. It provides fast transfer of information and are
or open an existing one.
cheaper to install and maintain. This paper provides an
Edit – Used for copying and pasting the code with further
efficient way of displaying messages on Notice Board
modification for font
using Wireless Technology. It also provides user
Sketch – For compiling and programming
authentication in order to avoid any misuse of proposed
Tools – Mainly used for testing projects. The Programmer
system.
section in this panel is used for burning a boot loader to
Electronic Notice Board is one of the application
the new microcontroller.
where WIFI and Bluetooth can be used effectively. It can
Help – In case you are feeling skeptical about software,
also be used in Malls and Highways for Advertisement
complete help is available from getting started to
purpose. A moving display with variable speed can also
troubleshooting.
be used in place of static display. Notice Board is the
Most Important Thing in All Institution, Organization, and
Public Place like Bus Stands, Airports, Railway Stations,
and Shopping Malls & Parks.
REFERENCES
[1]. P.Sampath Kumar,; V.Priyanka,;Lakshmi Surekha,;
Y.Harish Reddy.; “GSM based wireless electronic
All Rights Reserved © 2020 IJARTET 99
ISSN 2394-3777 (Print)
ISSN 2394-3785 (Online)
Available online at www.ijartet.com
International Journal of Advanced Research Trends in Engineering and Technology (IJARTET)
Vol. 7, Issue 7, July 2020
notice board display through ARM7 and LED”.ISSN Submitted Tasks." Journal of Internet Technology
2348-2370,May-2016 20, no. 7 (2019): 2055-2062.
[2]. T.Nizantha,; M.Venkateswari M.E “Digital [12]. Parthiban, K. G., S. Vijayachitra, and R. Dhanapal.
Classroom With Automatic Attendance And E- "Hybrid Dragonfly Optimization-Based Artificial
Notice Board Based On GSM & Biometric Neural Network for the Recognition of Epilepsy."
Authentication”. Proc. ISSN 2320-7345 2016. International Journal of Computational Intelligence
Systems 12, no. 2 (2019): 1261-1269.
[3]. Dharmendra Kumar Sharma,; Vineet Tiwari,;
Krishna Kumar,; B.A.Botre,; S.A.Akbar.“small and [13]. Dhanapal, R., and P. Visalakshi. "A Sector Based
medium range wireless electronic notice board using Energy Efficient Adaptive Routing Protocol for
Bluetooth and zigbee”. In Proceedings of the CSIR- Large Scale MANET." Research Journal of Applied
central electronic engineering research institute, Sciences, Engineering and Technology 9, no. 7
(2015): 478-484.
pilani, India, IEEE-2015, 978-1-4673-6540
[14]. Data, Energy Efficient Privacy-Preserving Big.
[4]. Neeraj Khera,;Divya Shukla,;Shambhavi Awasthi
"MCEEP-BDA: Multilevel Clustering Based-Energy
“development of simple and low cost android based
Efficient Privacy-Preserving Big Data Aggregation
wireless notice board” IEEE – 2016, 978-1-5090- in Large-Scale Wsn."
1489.
[5]. Ajinkya Gaikwad, Tej Kapadia, Manan Lakhani,
Deepak Karia. “Wireless Electronic Notice Board”.
ISSN, Volume: 02, Issue: 03|2013.
[6]. Bhumi Merai, Rohit Jain, Ruby Mishra. “Smart
Notice Board”. IJARCCE, Issue: 05|April-2015.
[7]. Dhanapal, R., & Visalakshi, P. (2015). Efficient
Clustering protocol based on Ant-Bee agent for
Large Scale MANET. International Journal of
Applied Engineering Research, 10(52), 2015.
[8]. Mathew, O. Cyril, R. Dhanapal, P. Visalakshi, K. G.
Parthiban, and S. Karthik. "Distributed Security
Model for Remote Healthcare (DSM-RH) Services
in Internet of Things Environment." Journal of
Medical Imaging and Health Informatics 10, no. 1
(2020): 185-193.
[9]. Dhanapal, R., & Visalakshi, P. (2016). Real time
health care monitoring system for driver community
using ADHOC sensor network. Journal of Medical
Imaging and Health Informatics, 6(3), 811-815.
[10]. Yuvaraj, N., G. Saravanan, R. Dhanapal, and M.
Premkumar. "Towards Efficient Data Transmission
using Energy-based Clustering Model (ECM-EDT)
in Heterogeneous VANET." (2020).
[11]. Dhanapal, R., T. Akila, Syed Shuja Hussain, and
Dinesh Mavaluru. "A Cost-Aware Method for Tasks
Allocation on the Internet of Things by Grouping the
All Rights Reserved © 2020 IJARTET 100
