(DIN 28082-2 - 1996-06) - Standzargen Fã R Apparate - Teil 2 - FuÃ - Ring Mit Pratzen Oder Doppelring Mit Stegen - MaÃ - e - 0001.de - en

GERMAN STANDARD
June 1996
Stand frames for apparatus DIN

Part 2: foot ring with claws or double ring with bars
Dimensions 28082-
2
ICS 71.120.10 Replacement for edition 1978-
05
Descriptors: stand frame, chemical process engineering, apparatus
Skirts for apparatus -

Part 2: Bottom ring with bracket supports or Twin ring with webs -
Dimensions
Huisseries pour appareils -
Game 2: Bague de fond avec double enveloppe-pattes ou bague double avec ämes -
Dimensions
This standard was approved by Working Committee 1-3 "Supporting Elements" of the Standards Committee for
Chemical Apparatus Construction(FNCA).
Changes
The following changes have been made with respect to DIN 28082-2: 1978-05:
a) Title changed
b) Standard designation added.
c) Change maximum screw forces.
d) Reference to proof of strength according to AD MerkbIan S 3/1 added.
e) Content editorially revised.
Previous issues
DIN 28082-2: 1977-06, 1978-05
1 scope of application 2nd Normative References

This standard is to be used for project planning dimensions for By means of dated or undated reference frames on
apparatuses, this standard contains predominantly procedural specifications from other publications. These
technical purposes serve and the additional normative references are interpreted in the respective places by
external moments are cited in the text, and the publications are below
(e.g. due to wind, earthquake acceleration, pipe thrust). listed. In the case of dated references, later ones belong
Proof of load capacity and general Changes or revisions to these publications Proof of stability of these frames and
theonly to this standard in case it is changed or revised Consideration of additional forces on the
equipmentprocessing are incorporated. For undated referenceswall is not part of this standard and must be dated the
latest edition of the referenced publication applies Users are rendered. Evidence can, to the extent cation.
applicable, according to AD leaflet S 3/1.DIN 13-28
For devices to be lined or linedMetric ISO thread - standard and fine threadto check in each case whether special
requirements are adequately met1 to 250 mm thread diameter - core cross
(e.g. from DIN 28051 or from DIN 28060).sections, stress cross sections and pitch angles
If thermal insulation is required, the user can DIN 8570-1
at its own discretion in a suitable manner General tolerances for welded structures -
constructions for removing the thermal insulation Length and angle dimensions
see, e.g. B. Support rings and brackets according to AGI working DIN 18800-1
sheet Q 153. Steel structures - design and construction
NOTE: For frames with only a small amount DIN 28007-1
Additional stress due to external moments General tolerances for columns - columns generally
DIN 28082-1 can be applied. my
Continued on pages 2 to 5
Standards Committee for Chemical Apparatus Construction (FNCA) in the DIN German Institute
for Standardization eV
@ DIN Deutsches Institut für Normung eV 'Any kind of reproduction, even in extracts, is only Ret. No. DIN 28082-2: 1996-06
permitted with the approval of the DIN Deutsches Institut für Normung e.?, Berlin.
Price gr. 07 Gerti: -He. 000z
Sole selling \ the number one by oe »tn Verlag GmbH. Joyyz Berlin
Page 2
DIN 28082-2: 1996-06
DIN 28051 AD leaflet S 3/1 *)

Chemical apparatus construction - constructive design of General proof of stability for printing
metallic building parts to be protected for coatings and container - container on stand frames
linings with organic materials
DIN28060 AD-Merkblatt W13 *)
Forgings and rolled parts made of unalloyed and
Containers and apparatus to be lined - construction alloyed steels
work
DIN 28082-1
AGI Q 153 **)
Frames for apparatus; with simple foot ring -
Insulation work on operational systems - brackets for
supporting structures
Dimensions
DIN EN 10025
Hot rolled products from unalloyed construction *) Available from: Beuth Verlag GmbH, 10772 Berlin
steel - Technical delivery conditions; GermanVersion **) To be obtained from: Curt R. Vincentz
EN 10025: 1990 Yerlag,PO Box 62 47; 30062 Hanover
3rd execution
General tolerances according to DIN 28007-1 and DIN 8570 - D. Dimensions in millimeters
BB
t0
AA
1
) Dimensions to be swept b1. b2. d1 d5. h1 h2, s1 s3 and s6
Page 3
DIN 28082-2: 1996-06
To picture 1
1 Stand frame with foot ring and claws (version P) or double ring with bars (version D).
2 Fire protection insulation by arrangement.
3 Crampon; by agreement for frames with h2> 2,000 mm.
4 Ventilation holes; up to a nominal diameter of 1,000 mm at least 2 pieces, diameter 60 mm, from a nominal diameter
of 1100 mm at least 4 pieces, diameter 100 mm. The ventilation holes must be placed as high as possiblebe.
5 Purge holes; 2 pieces opposite. Only effective if the upper edge of the inner foundation part is equal to the
upper edge of the foot ring.
Inspection opening (or passage)
For d1 <1000 mm: size by arrangement.
For d1 ≥ 1 000 mm: minimum width 600
mm
Height 1 200 mm.
If possible, arrange between the anchor bolts; do not use as pipe penetration.
7 Passage for pipes
4 designation
Designation of a stand frame with anchor bolt M36, double ring version with bars (D) with anchor slot (S):
Stand frame DIN 28082 - M36 - D - S
5 Dimensions, maximum tensile forces for anchor bolts

General tolerances according to DIN 28007-1 and DIN 8570-D. The unit millimeters (mm) applies to the dimensions
used in this standard.
Version D
double ring with Version P foot
webs ring and burst
20th
d
a) Details of the welds are not

specified in this standard. Fmax Traction | e anchor bolt
2nd
) One hole for attaching lightning protection earthing up to nominal diameter 1000 mm, two diametrically opposite
holes above.
Figure 2: Foot ring (version S is shown)

page 4 with anchor slot
DIN 28082-2: 1996-
06
Version S
Version L with
anchor hole
shown foot ring with bursts
Anchor slot or hole set axially free and arranged symmetrically to the main axis.
Figure 3: Version S with anchor slot and Version L with anchor hole
If the clear distance between the anchor claws is less than 1.5 times the plate width (I), a closed ring (double ring)
should be used here for design reasons.
Table 1: Dimensions and anchor bolt forces

Dimension s1 (see Figure 2) must be determined during the static calculation and must also be checked with the
reaction forces from the anchoring.
Screw
kN
thread
10038 ') 10570')
M24 80 60 28 32 60 120 180 45 35.4 53.1
12th
M30 95 75 35 40 70 120 190 55 300 35 25t 56.6 84.9
h
M36 110 85 42 48 80 160 220 65 82.8 124.2
M42 125 100 48 54 90 170 250 75 102.1 154.4

40 30t 16
M48 140 110 56 64 100 180 260 85 400 h 134.6 203.4
M56 155 125 66 76 120 220 300 95 45 35 186.2 281.4

20
M64 175 140 74 84 130 230 330 105 50 40 246.3 372.3
th
500 321.2 485.6
M72 x 6 195 155 82 92 140 240 340 115 55 45
M80 x 6 215 165 93 106 160 280 580 125 60 50 25 405.0 612.2
th
1
) Material number according to DIN EN 10025
2nd
) The dimensions s2, s4, s5 are reference values only for the project planning phase.
In the case of an order, they can be calculated according to AD leaflet S 3/1. Here,
the geometric conditions required must also be observed.
The values for the maximum tensile force of the anchor screw Fmax in Table 1 were determined with the yield
strengths fy, b, K at 20 ° C, a safety factor S = 2.2 and the core cross-section according to DIN 13-28.
Site5
DIN 28082-2: 1996-06
Table 2: Minimum yield strengths f " b, K ') for anchor bolts

according to DIN 18800 • 1
Screw thread
Material number
according to DIN up to M36 larger than M36
EN 10025 N / mm2 N / mm2
1.0038 240 215
1.0570 360
') For higher temperatures, the characteristic values specified for these materials in
AD-Merkblatt W13 apply.
6 Materials
Stand frame: The frame part to be welded to the apparatus wall must be suitable for this. The remaining parts of the
stand frame must at least correspond to the steel factory gate material no. 1.0038 according to DIN EN
10025.
Anchor bolts: minimum quality steel material no. 1.0038 or steel material no. 1.0570 according to DIN EN 10025.
Appendix A (informative)
References
DIN 8558-2
Design and execution of welded connections - tanks and apparatus made of steel for chemical plant construction
DIN EN 22553
Welded and soldered seams - Symbolic representation in drawings (ISO 2553: 1992); German version EN 22553:
1994

(DIN 28082-2 - 1996-06) - Standzargen Fã R Apparate - Teil 2 - FuÃ - Ring Mit Pratzen Oder Doppelring Mit Stegen - MaÃ - e - 0001.de - en

Uploaded by

Copyright:

Available Formats

(DIN 28082-2 - 1996-06) - Standzargen Fã R Apparate - Teil 2 - FuÃ - Ring Mit Pratzen Oder Doppelring Mit Stegen - MaÃ - e - 0001.de - en

Uploaded by

Document Information

Original Title

Copyright

Available Formats

Share this document

Share or Embed Document

Sharing Options

Did you find this document useful?

Is this content inappropriate?

Copyright:

Available Formats

(DIN 28082-2 - 1996-06) - Standzargen Fã R Apparate - Teil 2 - FuÃ - Ring Mit Pratzen Oder Doppelring Mit Stegen - MaÃ - e - 0001.de - en

Uploaded by

Copyright:

Available Formats

What is the purpose and scope of this standard?

What are the different versions/types of stand frames covered in this standard?

GERMAN STANDARD

Stand frames for apparatus DIN

Descriptors: stand frame, chemical process engineering, apparatus

Skirts for apparatus -

1 scope of application 2nd Normative References

DIN 28051 AD leaflet S 3/1 *)

5 Dimensions, maximum tensile forces for anchor bolts

a) Details of the welds are not

Figure 2: Foot ring (version S is shown)

shown foot ring with bursts

Table 1: Dimensions and anchor bolt forces

M42 125 100 48 54 90 170 250 75 102.1 154.4

M56 155 125 66 76 120 220 300 95 45 35 186.2 281.4

Table 2: Minimum yield strengths f " b, K ') for anchor bolts

You might also like