Data Sheet SS/267CS/269CS-EN Rev.

01

Model 267CS Multivariable

Model 269CS Multivariable
for mass flow

Measurement made easy

2600T Series Pressure

Transmitters

Engineered solutions for all

applications

Selectable maximum working pressure Reduced process penetrations

— Up to 41 MPa, 5945 psi — Saves money and reduces the chance of leaks

Base accuracy Fewer transmitters, less wiring and fewer shut-off valves
— ± 0.075 % / ± 0.04 % — Reduce installation costs

Span limits Greater reliability

— 0.05 ... 2000 kPa; 0.2 in H2O ... 290 psi — Due to fewer devices and less wiring
Differential pressure
— 0.6 ... 41 MPa; 87 ... 5945 psi absolute pressure Multiple communications protocol availability
— Provides integration into HART®, PROFIBUS PA and
Corrected mass flow measurement for gases, FOUNDATION fieldbus and Modbus platforms
steam and fluids — Upgrade options through interchangeable electronics
— Dynamic correction of pressure and temperature changes with automatic configuration

One transmitter replaces three separate transmitters Full compliance with PED category III
— Saving initial purchase costs
Series 2600T Pressure Transmitters SS/267CS/269CS
Model 267CS/269CS Multivariable

Introduction Discharge coefficient

This is defined as the true flowrate divided by the theoretical flowrate
Due to its multisensor technology, the 267C./269C. permits and corrects the theoretical equation for the influence of velocity
measurement of three separate process variables simultaneously and profile (Reynolds number), the assumption of no energy loss between
provides dynamic calculation of fully compensated mass flowrate for taps and pressure tap location. It is dependent on the primary flow
steam and liquids respectively standard volume flow for gases. It element, the diameter ratio (Beta ratio) and the Reynolds number.
measures differential pressure and absolute pressure from a single Reynolds number is in turn dependent on the viscosity, density and
sensor and process temperature from a standard Pt 100 Resistance velocity of the medium as well as the pipe diameter per the following
Temperature Detector (RTD). equation:
The flow calculation of this transmitter includes compensation of
pressure and/or temperature as well as more complex variables such
as discharge coefficient, thermal expansion, Reynolds number and v⋅ D⋅ ρ
Re = -------------------------
compressibility factor. υ
The 267C./269C. includes flow equations for superheated steam,
saturated steam, gases and liquids so that one model is all you need
in your system. v = velocity
D = interior pipe diameter
The enhanced compensation approach of 267C./269C. provides
ρ = medium density
much better accuracy than the “old approach” in which three different
υ = medium viscosity
transmitters, differential pressure, absolute pressure and
temperature, report their values to a DCS, PLC or flow computer. The
Dynamic compensation for discharge coefficient provides high
calculation considers changes in temperature and pressure
accuracy for flow measurement with primary flow elements.
according to the following formula:
p Gas expansion factor
Qm ≈ dp ---
T
This corrects for density differences between pressure taps due to
expansion of compressible media. It does not apply for liquids which
are essentially non-compressible.
The gas expansion factor is dependent on the diameter ratio, the
Isentropic exponent, the differential pressure and the static pressure
of the fluid according to the following equation:

For orifices:
dp
4 dp
Y 1 = 1 – ( 0.41 + 0.35 ⋅ β ) --------------
p⋅ κ
F
DP p
Meet For nozzles:
the
2 κ – 1- 1
Future ⎛ ---⎞ ⎛ ⎞⎛ ----------- ⎞ ---
⎜ ⎛ dp⎞ κ⎟ ⎜ κ ⎟ 2
P T ⎟⎜ ⎛ ------⎞
dp
κ ------
⎜ ⎝ p ⎠ ⎟⎜ 4 ⎟⎜ 1 – ⎟
Flow

Flow

1–β ⎝ p⎠
Y 1 = ⎜⎜ --------------------⎟⎟ ⎜⎜ ---------------------------------⎟⎟ ⎜⎜ -----------------------------------⎟⎟
κ–1 2
⎜ ⎟⎜ ---⎟ ⎜ 1 – ⎛ dp ------⎞ ⎟
4 ⎛ dp⎞ κ⎟ ⎜ ⎝ p⎠ ⎟
T Qm ⎜ ⎟⎜
⎝ ⎠ ⎝ 1 – β ⎝ ------ p ⎠ ⎠⎝ ⎠
Qv
β = ratio of diameters (Beta ratio)
15_d0030 dp = differential pressure
p = static pressure
κ = Isentropic exponent

The dynamic mass flow compensation of 267C./269C. is based on Velocity of approach factor
the following formula (according to EN ISO 5167/AGA 3:
Is dependent on the Beta ratio as defined by the following equation:
2
Qm ≈ C ⋅ Ev ⋅ Y1 ⋅ d dp ⋅ ρ 1
E v = --------------------
4
1–β
Qm = mass flowrate
C = discharge coefficient Beta ratio is dependent on bore diameter and pipe diameter which in
Ev = velocity of approach factor turn are functions of temperature. The material of the process pipe
Y1 = gas expansion factor and primary flow element expands or contracts with changes in
d = bore diameter temperature of the fluid being measured. The thermal expansion
dp = differential pressure coefficients are dependent on the the material of the pipe and flow
ρ = fluid density element and are used for calculating the change in diameters.
This ensures high flowrate accuracy during low and high temperature
The following standards are used for flow calculation: applications.
– AGA 3
– DIN EN ISO 5167

2
Series 2600T Pressure Transmitters SS/267CS/269CS
Model 267CS/269CS Multivariable

Medium density Functional Specifications

This directly affects the flowrate calculation. The 267C./269C.
compensates for density of media resulting from changes in Measuring range and span limits
temperature and/or pressure as follows:
Differential pressure sensors
• Gases as a function of p and T per the gas law equations.
Upper range Lower range
Calculation of the compressibility factors for natural gas is Sensor code Minimum span
limit (URL) limit (LRL)
described in the American AGA 8 standard.
• Super-heated steam as function of p and T based on steam tables 1 kPa 0 0.05 kPa
• Saturated steam as function of p based on steam tables A 10 mbar 0.5 mbar
• Liquids as a function of T 4 in H2O 0.2 in H2O
6 kPa 0 0.2 kPa
Mass flow calculation with the 267C./269C. will be configured for the
C 60 mbar 2 mbar
following differential flow sensors:
24 in H2O 0.8 in H2O
Orifice corner taps, ISO 40 kPa 0 0.4 kPa
Orifice flange taps, ISO F 400 mbar 4 mbar
Orifice D and D/2 taps, ISO 160 in H2O 1.6 in H2O
Orifice corner taps, ASME
Orifice flange taps, ASME 250 kPa 0 2.5 kPa
Orifice D and D/2 taps, ASME L 2500 mbar 25 mbar
Orifice flange taps, AGA3 1000 in H2O 10 in H2O
Orifice 2.5D and 8D taps 2000 kPa 0 20 kPa
Small bore orifice, flange taps N 20 bar 0.2 bar
Small bore orifice, corner taps 290 psi 2.9 psi
Nozzle ISA 1932
Nozzle, long radius wall tap, ISO
Nozzle, long radius wall tap, ASME Absolute pressure sensors
Venturi, rough cast inlet, ISO
Venturi, machined inlet, ISO Upper range Lower range
Sensor code Minimum span
Venturi, welded inlet, ISO limit (URL) limit (LRL)
Venturi, rough cast inlet, ASME 600 kPa 0 abs 6 kPa
Venturi, machined inlet, ASME 1 6 bar 0.06 bar
Venturi, welded inlet, ASME 87 psi 0.87 psi
Venturi, nozzle, ISO
2000 kPa 0 abs 20 kPa
Area Averaging Meter
2 20 bar 0.2 bar
Pitot tube, ISO 3966
290 psi 2.9 psi
V-cone
Wedge element 10000 kPa 0 abs 100 kPa
Integral Orifice Assembly 3 100 bar 1 bar
Density correction (unknown primary element) 1450 psi 14.5 psi
41000 kPa 0 abs 410 kPa
Configuration of full functionality of 267C./269C. including all data 4 410 bar 4.1 bar
necessary for mass flow compensation will use the PC-based tool
5945 psi 59.5 psi
SMART VISION with DTM MV 2600T.

Span limits
Maximum span = URL = upper range limit
(with the flow measurement shut off, can be adjusted up to ± URL
within the measurement span.
Example: -400 ... +400 mbar)
In order to optimize performance characteristics, it is recommended
to select the transmitter sensor providing the lowest turndown ratio.
Zero suppression and elevation
No suppression or elevation, but zero-based range if:
– calibrated span ≥ minimum span
Process temperature range
-50 °C to +650 °C (-58 °F to 1200 °F) with external four-wire RTD.
Damping
Adjustable time constant: 0 to 60 sec
This is in addition to sensor response time.
Warm-up period
Operation within specifications: ≤ 2.5 sec with minimal damping
Insulation resistance
> 100 MΩ at 1000 V DC (between terminals and ground)

3
Series 2600T Pressure Transmitters SS/267CS/269CS
Model 267CS/269CS Multivariable

Operating limits Environmental limits

Electromagnetic compatibility (EMC)
Temperature limits °C (°F):
Definition Class 3
Ambient (operating temperature) RFI suppression Limit Class B
(according to EN 550011)
Transmitter: -40 °C to +85 °C (-40 °F and +185 °F)
Meets NAMUR recommendations
LCD display: -20 °C to +70 °C (-4 °F and +158 °F)
Lower operating temperature Low voltage directive:
for Viton and PTFE gaskets. -20 °C (-4 °F)
Meets 73/23/EC
Note: Pressure equipment directive (PED)
For hazardous atmosphere applications, see the temperature range
Instruments with maximum working pressure 41 MPa, 410 bar,
specified on the relevant certificate/approval.
5945 psi comply with 97/23/EC Category III module H.
Process
Humidity
Lower limit
Relative humidity: up to 100 %
– Refer to the lower ambient temperature limits
Condensation, icing: permitted
Upper limit:
– Silicone oil: 120 °C (248 °F) for operating pressures Vibration resistance
≥ 10 kPa abs, 100 mbar abs, 1.45 psia (1) Acceleration up to 2 g at frequencies up to 1000 Hz
– Carbon fluoride: 120 °C (248 °F) for operating pressures (according to IEC 60068-2-26)
≥ atmospheric pressure (2)
Shock resistance (according to IEC 60068-2-27)
(1) 85 °C (185 °F) for applications below 10 kPa abs, 100 mbar abs, Acceleration: 50 g
1.45 psia to 3.5 kPa abs, 35 mbar abs, 0.5 psia Duration: 11 ms
(2) 85 °C (185 °F) for applications below atmospheric pressure up to
40 kPa abs, 400 mbar abs, 5.8 psia Wet and dust-laden atmospheres (protection type)
The transmitter is dust and sand-tight and protected against
Storage immersion effects as defined by IEC EN60529 (1989) to IP 67 (IP 68
Lower limit: -50 °C (-58 °F), -40 °C (-40 °F) for LCD displays on request) or by NEMA to 4X or by JIS to C0920.
Upper limit: +85 °C (+185 °F) Protection type with plugged connection: IP 65

Hazardous atmospheres
Pressure limits
Transmitter of protection type "Intrinsically safe EEx ia"
Overpressure limits (without damage to the transmitter)
according to Directive 94/9/EC (ATEX)
Lower limit
– 0.5 kPa abs, 5 mbar abs, 0.07 psia for silicone oil For applications in explosive areas, the connected RTD must also
– 40 kPa abs, 400 mbar abs, 5.8 psia for carbon fluoride have the respective Ex protection class as the transmitter.

Upper limit: Transmitter with 4 to 20 mA output signal and HART communication

– 0.6 MPa, 6 bar, 87 psi for differential pressure sensor code A Identification: II 1/2 GD T 50 °C EEx ia IIC T6
– 2 MPa, 20 bar, 290 psi or 10 MPa, 100 bar, 1450 psi or 41 MPa, II 1/2 GD T 95 °C EEx ia IIC T4
410 bar, 5945 psi depending upon the selected code variant for
sensor code C, F, L, N Power supply and signal circuit with protection type Intrinsic Safety
EEx ib IIB/IIC or EEx ia IIB/IIC for connection to supply units with
Static pressure maximum values:
The 267C./269C. transmitter for mass/standard volume flow II 1/2 GD T 50 °C EEx ia or ib IIC T6
operates within specifications with the following limits: II 1/2 GD T 95 °C EEx ia or ib IIC T4
Lower limit For temperature class T4:
– 3.5 kPa abs, 35 mbar abs, 0.5 psia for silicone oil Ui = 30 V
– 40 kPa abs, 400 mbar abs, 5.8 psia for carbon fluoride Ii = 200 mA
Pi = 0.8 W for T4 where Ta = -40 °C to +85 °C (-40 °F to +185 °F)
Upper limit:
Pi = 1.0 W for T4 where Ta = -40 °C to +70 °C (-40 °F to +158 °F)
– 0.6 MPa, 6 bar, 87 psi for differential pressure sensor code A
– 2 MPa, 20 bar, 290 psi or 10 MPa, 100 bar, 1450 psi or 41 MPa, For temperature class T6:
410 bar, 5945 psi depending upon the selected code variant for Pi = 0.7 W for T4 where Ta = -40 °C to +40 °C (-40 °F to +104 °F)
sensor code C, F, L, N
Effective internal capacitance: Ci ≤ 10 nF
Test pressure Effective internal inductance: Li ≈ 0
For pressure testing purposes, the transmitter can withstand a
pressure test applied simultaneously from both sides of up to 1.5
times the static pressure range of the transmitter.

4
Series 2600T Pressure Transmitters SS/267CS/269CS
Model 267CS/269CS Multivariable

Fieldbus transmitters (PROFIBUS PA / FOUNDATION fieldbus) Transmitter of protection type "Intrinsically safe EEx ia"
Identification: II 1/2 GD T 50 °C EEx ia IIC T6 according to Directive 94/9/EC (ATEX), or
II 1/2 GD T 95 °C EEx ia IIC T4
protection type "flameproof enclosure EEx d" according to
Power supply and signal circuit with protection type Intrinsic Safety Directive 94/9/EC (ATEX), or
EEx ib IIB/IIC or EEx ia IIB/IIC for connection to supply units with
maximum values: protection type "Limited energy equipment EEx nL" according to
II 1/2 GD T 50 °C EEx ia or ib IIC T6 Ui = 17.5 V Directive 94/9/EC (ATEX) (alternate certification)
II 1/2 GD T 95 °C EEx ia or ib IIC T4 Ii = 360 mA
Pi = 2.52 W Transmitter with 4 to 20 mA output signal and HART communication
Identification: II 1/2 GD T50 °C EEx ia IIC T6
II 1/2 GD T 50 °C EEx ia or ib IIB T6 Ui = 17.5 V II 1/2 GD T95 °C EEx ia IIC T4;
II 1/2 GD T 95 °C EEx ia or ib IIB T4 Ii = 380 mA (refer to "EEx ia" for additional data)
Pi = 5.32 W or

or connection to supply units or barriers with linear characteristics: Identification: II 1/2 GD T85 °C EEx d IIC T6
Maximum values:
II 1/2 GD T 50 °C EEx ia or ib IIC T6 Ui = 24 V Ambient temperature range:
II 1/2 GD T 95 °C EEx ia or ib IIC T4 Ii = 250 mA -40 °C to +75 °C (-40 °F to +167 °F)
Pi = 1.2 W or

Effective internal inductance: Li ≤ 10 μH, Identification: II 3 GD T 50 °C EEx nL IIC T6

Effective internal capacitance: Ci ≈ 0 II 3 GD T95 °C EEx nL IIC T4
(refer to "EEx nL" for additional data)
Maximum permissible ambient temperatures depending on the
temperature class:
Factory Mutual (FM)
Temperature class ambient temperature ambient temperature Transmitter with 4 to 20 mA output signal and HART communication
lower limit upper limit Intrinsically Safe: Class I; Division 1; Groups A, B, C, D;
T4 -40 °C (-40 °F) +85 °C (+185 °F) Class I; Zone 0; Group IIC; AEx ia IIC
Degree of protection:NEMA Type 4X (indoor or outdoor)
T5, T6 -40 °C (-40 °F) +40 °C (+104 °F)
Maximum permissible ambient temperatures depending on the
Transmitter of category 3 for the application in "Zone 2" temperature class:
according to Directive 94/9/EC (ATEX)
Umax = 30 V, Ci = 10.5 nF, Li = 10 μH
Transmitter with 4 to 20 mA output signal and HART communication
Identification: II 3 GD T 50 °C EEx nL IIC T6 Temperature
Ambient temperature Imax Pi
II 3 GD T 95 °C EEx nL IIC T4 class
-40 °C to +85 °C (-40 °F to +185 °F) 0.8 W
Operating conditions: T4 200 mA
Supply and signal circuit -40 °C to +70 °C (-40 °F to +158 °F) 1W
(terminal signal ±): U ≤ 45 V T5 0.75 W
I ≤ 22.5 mA -40 °C to +40 °C (-40 °F to +104 °F) 25 mA
T6 0.5 W
Connector for passive external temperature sensor:
Supply and signal circuit U ≤ 10.6 V Fieldbus transmitters
I ≤ 1.5 mA (PROFIBUS PA / FOUNDATION fieldbus)
P ≤ 4 mW Intrinsically Safe: Class I, II, and III; Division 1;
Groups A, B, C, D, E, F, G;
Ambient temperature range:
Class I; Zone 0; AEx ia Group IIC T6, T4;
Temperat. class T4 and T6 Ta = -40 °C to +85 °C (-40 °F to +185 °F)
Non-incendive Class I, II, and III; Division 2;
Temperat. class T5 and T6 Ta = -40 °C to +40 °C (-40 °F to +104 °F)
Groups A, B, C, D, F, G

Transmitter of protection type "flameproof enclosure EEx d" Transmitter with 4 to 20 mA output signal and HART communication
according to Directive 94/9/EC (ATEX) and fieldbus transmitter (PROFIBUS PA/FOUNDATION fieldbus)
Transmitter with 4 to 20 mA output signal and HART communication Explosion Proof: Class I, Division 1, Groups A, B, C, D;
and fieldbus transmitter (PROFIBUS PA/FOUNDATION fieldbus) Class II/III, Division 1, Groups E, F, G
Identification: II 1/2 G EEx d IIC T6 Degree of protection:NEMA Type 4X (indoor or outdoor)

Operating conditions: Canadian standard (CSA)

Ambient temperature range: -40 °C to +75 °C (-40 °F to +167 °F)
Transmitter with 4 to 20 mA output signal and HART communication
and fieldbus transmitter (PROFIBUS PA/FOUNDATION fieldbus)
Explosion Proof: Class I, Division 1, Groups B, C, D;
Class II/III, Division 1, Groups E, F, G
Degree of protection:NEMA Type 4X (indoor or outdoor)

5
Series 2600T Pressure Transmitters SS/267CS/269CS
Model 267CS/269CS Multivariable

Standards Association of Australia (SAA) LCD display (optional)

19-segment alphanumeric display (2-line, 6-character ) with
Transmitter of protection type "Intrinsically safe Ex ia" and "Non-
additional bar chart display, optionally with back illumination.
sparking material" Ex n User-specific display:
Transmitter with 4 to 20 mA output signal and HART communication Output current in percent or
Identification: Output current in mA or
Ex ia IIC T4 (Pi 0.8 W Ta = 85 °C) / T6 (Pi 0.7 W Ta = 40 °C) Freely-selectable process variable
Ex n IIC T4 (Ta = 85 °C / T6 (Ta = 40 °C) Diagnostic messages, alarms, measuring range infringements and
IP 66 changes to the configuration are also displayed.

Intrinsically safe installation input parameters: Output signal

Ui = 30 V Two-wire 4 to 20 mA, related to mass / standard volume flow, full
Ii = 200 mA compensation of all pressure (p) and temperature (T) effects.
Pi = 0.8 W for T4 where Ta = +85 °C (+185 °F) or HART® communication provides digital process variables (%, mA or
Pi = 0.7 W for T4 where Ta = +40 °C (+104 °F) engineering units) superimposed on the 4 to 20 mA signal (protocol
according to Bell 202 FSK standard).
Effective internal capacitance: Ci = 52 nF
Effective internal inductance: Li ≈ 0 mH Output function
Mass / standard volume flow calculations are performed according to
Ex n installation input parameters: the following:
Ui = 30 V
2
Qm ≈ C ⋅ Ev ⋅ Y1 ⋅ d dp ⋅ ρ For steam/fluid
Transmitter with protection type "flameproof enclosure Ex d"
Transmitter with 4 to 20 mA output signal and HART communication
and fieldbus transmitter (PROFIBUS PA/FOUNDATION fieldbus,
Modbus) 2 1
Qn ≈ C ⋅ Ev ⋅ Y1 ⋅ d dp ⋅ ρ – ----- For gas
Identification: ρn
Zone 1: Ex d IIC T6 (Tamb +75 °C) IP66/IP67
Zone A21: Ex tD A21 T85 (Tamb +75 °C) IP66/IP67
where:
Qm = mass flowrate
Electrical Data and Options Qn = standard flowrate
C = discharge coefficient
Ev = velocity of approach factor
HART digital communication and 4 to 20 mA output Y1 = gas expansion factor
Power supply d = bore diameter
dp = differential pressure
The transmitter operates from 10.5 to 45 V DC with no load and is
ρ = fluid density
protected against reverse polarity connection
ρ n = standard density
(additional load allows operations over 45 V DC).
Minimum power supply is 14 V DC with backlit display.
For EEx ia and other intrinsically safe approval power supply must not Output current limits (according to NAMUR standard)
exceed 30 V DC. Overload condition
– Lower limit: 3.8 mA (configurable down to 3.6 mA)
Ripple
– Upper limit: 20.5 mA (configurable up to 22.5 mA)
Maximum permissible voltage ripple of power supply during
communication:
Alarm current
7 Vss at f = 50 to 100 Hz
1 Vss at f = 100 to 200 Hz Minimum alarm current: configurable from 3.6 to 4 mA.
0.2 Vss at f = 200 to 300 Hz Standard setting: 3.6 mA
Maximum alarm current: configurable from 20 to 22.5 mA.
Standard setting: 21 mA
Load limitations
Standard setting: maximum alarm current
Total loop resistance at 4 to 20 mA and HART:
Supplyvoltage – minimumoperatingvoltage (V DC) SIL – functional safety (optional) according to IEC 61508/61511
R ( kΩ) = ---------------------------------------------------------------------------------------------------------------------------------------------------
22.5 m A Device with certificate of conformity for use in safety-relevant
applications, including SIL 2.
A minimum of 250 Ω is required for HART communication.

6
Series 2600T Pressure Transmitters SS/267CS/269CS
Model 267CS/269CS Multivariable

Measuring accuracy Operating influences

Reference conditions according to IEC 60770 apply: ambient Ambient temperature
temperature of 20 °C (68 °F), relative humidity of 65 %, atmospheric (turndown to 15:1)
pressure of 1013 hPa (1013 mbar), mounting position with vertical Per 20 K change between the limits of
diaphragm and zero-based range for transmitter with isolating -20 °C to +65 °C (-4 °F to +149 °F)
diaphragms in Hastelloy and silicone oil fill. Measurement range with
HART digital trim values equal to 4 to 20 mA span end points. Differential pressure sensor
267CS
Unless otherwise specified, errors are quoted as % of span. ± (0.04 % URL + 0.065 % span)
The accuracy related to the Upper Range Limits (URL) is affected by 269CS
the actual turndown (TD) as a ratio between Upper Range Limit (URL) ± (0.03 % URL + 0.05 % span)
and calibrated span (URL/span).
Absolute pressure sensor
In order to optimize performance characteristics, it is recommended ± (0.08 % URL + 0.08 % span)
to select the transmitter sensor providing the lowest turndown ratio. Limited to ± (0.1 % URL + 0.1 % span) per the complete temperature
range of 120 K (216 °F)
Dynamic behavior (according to IEC 61298-1)
Devices with standard configuration and turndown to 30:1 Static pressure
Dead time: 30 ms (zero errors can be calibrated out at line pressure)
Time constant (63.2 % of total step change)
– Sensors F to N: 150 ms Measuring range Sensor A Sensors C, F, L, N
– Sensor C: 400 ms to 2 bar: to 100 bar:
– Sensor A: 1000 ms 0.05 % URL 0.05 % URL
On zero
> 2 bar: > 100 bar:
Accuracy rating 0.05 % URL/bar 0.05 % URL/100 bar
Percentage of calibrated span including combined effects of linearity, to 2 bar: to 100 bar:
hysteresis and reproducibility. 0.05 % span 0.05 % span
For fieldbus versions SPAN refers to analog input function block On span
outscale range. > 2 bar: > 100 bar:
0.05 % span/bar 0.05 % span/100 bar
Differential pressure sensor
267CS
– ± 0.075 % for turndown from 1:1 to 10:1 Power supply
Within the specified limits for the voltage/load the total influence is less
– ± ⎛ 0.075 + 0.005 × ------------
URL
- – 0.05⎞ % For turndown than 0.001 % of URL per volt.
⎝ Span ⎠ greater than 10:1
Load
269CS Within the specified load/voltage limits, the total effect is negligible.
– ± 0.04 % for turndown from 1:1 to 10:1
Electromagnetic fields
– ± ⎛ 0.04 + 0.005 × ------------
URL
- – 0.05⎞ % For turndown Total effect: less than 0.05 % of span from 80 to 1000 MHz and for
⎝ Span ⎠ greater than 10:1 field strengths up to 10 V/m when tested with unshielded conduit,
with or without meter.
Absolute pressure sensor
Common-mode interference
0.1 % of the URL of the absolute pressure sensor
No effect from 250 Veff (50 Hz) or 50 V DC
Process temperature measurement (Pt 100)
± 0.3 °C (0.54 °F) Installation position
Rotations in the plane of the transmitter diaphragm have negligible
The accuracy of the mass or standard volume flow is not only effect. A tilt from vertical causes a zero shift of sin α x 0.35 kPa (3.5
influenced by the accuracy of the dp, p and T measurement; rather it mbar, 1.4 in H2O) of URL which can be corrected with the zero
depends upon the primary device used (discharge coefficient), the adjustment. No effect on the span.
pressure and temperature range to be compensated, as well as other
parameters. Stability
Typical applications reflect an accuracy of 0.7 % to 0.9 %. ± 0.15 % of URL over a sixty-month period
Vibration effect
± 0.10 % of URL (according to IEC 61298-3)

8
Series 2600T Pressure Transmitters SS/267CS/269CS
Model 267CS/269CS Multivariable

Technical Specification Optional accessories

(Refer to ordering information sheets for variant availability related to the Mounting bracket
specific model) For vertical and horizontal 60 mm (2 in) pipes or wall mounting
LCD display
Materials
Plug-in and rotatable
Process isolating diaphragms1)
Additional tag plate
Hastelloy C276™ stainless steel (1.4435); Monel 400™,
Tantalum Tag with wire (both stainless steel) attached to the transmitter, with a
maximum of 30 characters including spaces.
Process flange, adapter, plugs and drain/vent valves1)
Cleanliness level for oxygen application
Hastelloy C276™ stainless steel (1.4404); Monel 400™; Kynar (PVDF)
Preparation for hydrogen application
Sensor fill fluid
Silicone oil, inert fill (carbon fluoride) Certificates (test, model, calibration, material traceability)
Sensor housing
Stainless steel
Process connections
Flange: ¼-18 NPT on the process axis, selectable with fixing threads
Mounting bracket 7/16-20 UNF or DIN 19213 connection with M10 threading for
Stainless steel operating pressures up to 10 MPa, 100 bar, 1450 psi or M12
threading for higher operating pressures up to 41 MPa, 410 bar,
Gaskets1) 5945 psi
Viton™ (FPM), Perbunan (NBR), EPDM, PTFE (for sensor C, F, L, N) Adapter: ½-14 NPT on process axis
or FEP coated Viton™ (for sensor A) Center distance between flanges: 54 mm (2.13 in);
51, 54 or 57 mm (2.01, 2.13 or 2.24 in) as per adapter fittings
Bolts and nuts
Stainless steel, bolts and nuts Class A4-70 according to ISO 3506, Electrical connections
conforming to NACE MR0175 Class II
Two ½-14 NPT or M20 x 1.5 threaded bores for cable glands, direct
Electronics housing and cover on housing, or plug connector
Barrel version – HART: straight or angle Harting Han connector and one plug
– Aluminum alloy with low copper content, – FOUNDATION fieldbus/PROFIBUS PA; plug 7/8 in / M12 x 1
baked epoxy finish
Terminal blocks
– Stainless steel
HART version: four terminals for signal/external display plus four
DIN version terminals for RTD connection wiring up to 2.5 mm² (14 AWG) and four
– Aluminum alloy with low copper content, connection points for test and communication purposes.
baked epoxy finish Fieldbus versions: two terminals for signal (bus connection) plus four
terminals for RTD connection wiring up to 2.5 mm² (14 AWG)
Covers O-ring
Viton™ Ground
Internal and external 4 mm² (12 AWG) ground termination points are
Local control keys provided.
Fiberglass-reinforced polycarbonate plastic (removable), no local
control keys for stainless steel housings. Installation position
Type plate The transmitter can be mounted in any position.
Stainless steel (316) or plastic data plate attached to the electronics The electronics housing may be rotated 360°. A positive stop
housing prevents over-travel.

Calibration Weight (without options)

Standard: at maximum span, zero-based range, ambient Approximately 3.5 kg (8lb), add 1.5 kg ( 3.4lb) for stainless steel
temperature and pressure housing. Packaging adds 650 g
Optional: at specified range and ambient conditions
Packaging
Carton approx. 230 x 250 x 270 mm (9 x 10 x 11 in)

™ Hastelloy is a Cabot Corporation trademark

™ Monel is an International Nickel Co. trademark
™ Viton is a DuPont de Nemours trademark

1) Wetted transmitter parts

9
Series 2600T Pressure Transmitters SS/267CS/269CS
Model 267CS/269CS Multivariable

Mounting Dimensions (not design data)

Transmitter with barrel housing

Deviations in the drawing are possible. Measurements in mm (inches)

Space must be available to

rotate the keyboard cover

70 (2.76)
114 (4.49) 23 (0.91) LCD display

9 (0.35) 58 (2.28) 20 (0.79)

Terminal side Clearance for
cover removal
required

(1.02)
26
Additional tag plate,
e.g., for indicating
measuring points
(optional)
Housing rotating

186 (7.32)
108 (4.25)
Threaded bore
stop-screw
(optional) ¼-18 NPT
Drain/vent valve (optional) for drain/vent valve

Transducer

61 (2.40)
(1.63)

plate
41.3

(1.18)

-+
30

Process
connection
54 (2.13) Threads for fixing screws 90 (3.54)
(see process flange data)
96 (3.78)
71 (2.80)

Electrical connection Plate with key

legend

Type plate
∅ 83 (3.27)

140 (5.51)

Housing cover

Pt 100 connection Captive screw for

keyboard cover

15_0085x1

11
Series 2600T Pressure Transmitters SS/267CS/269CS
Model 267CS/269CS Multivariable

Transmitter with DIN housing

Deviations in the drawing are possible. Measurements in mm (inches)
Pt 100 connection

70 (2.76)

140 (5.51)
83 (3.27)
Space must be available
to rotate the keyboard
cover 43
(1.69)
Electrical connection
Additional tag plate, e.g., for
indicating measuring points Housing rotating Captive screw for
(optional) stop-screw keyboard cover
61 (2.40)

Plate with key

legend
90 (3.54)

96 (3.78) 20 (0.79)
107 (4.21)
Transducer 54 (2.13)
plate 138 (5.43)
168 (6.61) 23 (0.91)
Process LCD display
connection
(1.63)
41.3

Threads for fixing

screws (see
process flange
data) Terminal side

Type plate
Electrical connection

Housing cover 15_0086x1

27 (1.06) 48 (1.89)
20 (0.79)
139 (5.47) Clearance for
cover removal
required

12
Series 2600T Pressure Transmitters SS/267CS/269CS
Model 267CS/269CS Multivariable

Mounting options with bracket

Deviations in the drawing are possible. Measurements in mm (inches)

∅ 11 (0.43)

∅ 10 (0.4)

72 (2.83)
60(2.36) 135.5 (5.33)
72 (2.83)

57(2.24)
72 (2.83)

136 (5.35)
56(2.20) 110 (4.33)

214 (8.43)
M01517x1

Vertical pipe mounting Horizontal pipe mounting Vertical pipe mounting and Horizontal pipe mounting and
transmitter above the mounting transmitter above the
bracket mounting bracket

M01520x1 M01521x1

M01518x1 M01519x1

13
Series 2600T Pressure Transmitters SS/267CS/269CS
Model 267CS/269CS Multivariable

Electrical connections

Standard terminal block

Grounding/potential
Test sockets for 4 to 20 mA equalizing terminal Output signal/power supply Fieldbus plug connector
(not with Fieldbus
transmitters) 7/8 in connector
1 3

Cable Pt 100 cable entry

entry 2 4

M12 x 1 connector
14 12 Connection for Pt 100 2
13 TEST 11
SIGNAL
- + - +
3 1
Screw terminals for leads with 0.5
to 2.5 mm² cross-section
4 15_0066x1

Pin (male) assignment

Number FOUNDATION PROFIBUS PA
Fieldbus
1 FF- PA+
2 FF+ Ground
3 Shield PA shield
4 Ground

Mating plug (socket) not supplied

M01450x1

Harting Han 8D (8U) connector

DIN housing Barrel housing

1 2

- +
Harting Han 8D (8U) pin assignment
(socket view)

15_0079x1

14
Series 2600T Pressure Transmitters SS/267CS/269CS
Model 267CS/269CS Multivariable

Ordering information
Multivariable transmitter, for mass flow Variant digit No. 1- 6 7 8 9 10 11 Code
267CS Base accuracy: 0.075 % Catalog No. 267CS-
269CS Base accuracy: 0.04 % Catalog No. 269CS-
Sensor - Span limits
1 kPa 10 mbar 4 in. H2O A
6 kPa 60 mbar 24 in. H2O (45 mm Hg) C
40 kPa 400 mbar 160 in. H2O (300 mm Hg) F
250 kPa 2500 mbar 1000 in. H2O (1875 mm Hg) L
2000 kPa 20 bar 290 psi N
100 kPa 1000 mbar 400 in. H2O Y
Static pressure
0 ... 0.6 MPa 0 ... 6 bar 0 ... 87 psi 1) 1
0 ... 2 MPa 0 ... 20 bar 0 ... 290 psi 2) 2
0 ... 10 MPa 0 ... 100 bar 0 ... 1450 psi 2) 3
0 ... 41 MPa 0 ... 410 bar 0 ... 5945 psi 2) 4
Diaphragm material / Fill fluid
AISI 316L SST (1.4435) Silicone oil NACE S
Hastelloy C-276 Silicone oil NACE K
Monel 400 Silicone oil NACE M
Monel 400 gold plated Silicone oil NACE V
Tantalum Silicone oil NACE T
AISI 316L SST (1.4435) Inert fluid NACE 3) A
Hastelloy C-276 Inert fluid NACE 3) F
Monel 400 Inert fluid NACE 3) C
Monel 400 gold plated Inert fluid NACE 3) Y
Tantalum Inert fluid NACE 3) D
Process connection material / Process connection
AISI 316L SST (1.4404 / 1.4408) 1/4-18 NPT-f direct NACE A
AISI 316L SST (1.4404 / 1.4408) 1/4-18 NPT-f direct (DIN 19213) NACE C
AISI 316L SST (1.4404 / 1.4408) 1/2-14 NPT-f through adapter NACE B
Hastelloy C-276 1/4-18 NPT-f direct NACE D
Hastelloy C-276 1/4-18 NPT-f direct (DIN 19213) NACE F
Hastelloy C-276 1/2-14 NPT-f through adapter NACE E
Monel 400 1/4-18 NPT-f direct NACE G
Monel 400 1/4-18 NPT-f direct (DIN 19213) NACE L
Monel 400 1/2-14 NPT-f through adapter NACE H
Kynar (PVDF) (axial) 1/4-18 NPT-f direct (max. 1 MPa) P
AISI 316L SST (1.4404 / 1.4408) (vertical) 1/4-18 NPT-f direct NACE Q
Bolts / Gaskets
AISI 316L SST (NACE - non exposed) Viton 4) 3
AISI 316L SST (NACE - non exposed) PTFE (Max. 10 MPa) 5) 4
AISI 316L SST (NACE - non exposed) EPDM 5) 5
AISI 316L SST (NACE - non exposed) Perbunan 5) 6
AISI 316L SST FEP (Only available with Kynar [PVDF] process connection) T

1) Only with Sensor code A Continued on next page

2) Not with sensor code A
3) Suitable for oxygen applications
4) Suitable for oxygen applications / Not with Process Connection Kynar (PVDF)
5) Not with Process Connection Kynar (PVDF)

15
Series 2600T Pressure Transmitters SS/267CS/269CS
Model 267CS/269CS Multivariable

Ordering Information, continued

Multivariable transmitter, for mass flow Variant digit No. 1- 6 9 10 11 12 13 Code
267CS Base accuracy: 0.075 % Catalog No. 267CS-
269CS Base accuracy: 0.04 % Catalog No. 269CS-
Electronic housing
material Electrical connection
Aluminium Alloy (Barrel type) 1/2-14 NPT A
Aluminium Alloy (Barrel type) M20 x 1.5 6) B
Aluminium Alloy (Barrel type) Harting Han connector 7) E
Aluminium Alloy (Barrel type) Fieldbus connector 8) G
AISI 316L SST (Barrel type) 1/2-14 NPT S
AISI 316L SST (Barrel type) M20 x 1.5 6) T
Aluminium Alloy (DIN type) M20 x 1.5 6) J
Aluminium Alloy (DIN type) Harting Han connector 7) K
Aluminium Alloy (DIN type) Fieldbus connector 8) W
Output Additional options
HART digital communication and 4 ... 20 mA (Additional options not requested) 10) H
HART digital communication and 4 ... 20 mA (Additional options to be ordered by additional 9) 1
ordering code)
PROFIBUS PA (Additional options not requested) 10) P
PROFIBUS PA (Additional options to be ordered by additional 9) 2
ordering code)
FOUNDATION fieldbus (Additional options not requested) 10) F
FOUNDATION fieldbus (Additional options to be ordered by additional 9) 3
ordering code)
Modbus RS 485 (Additional options not requested) 10) M
Modbus RS 485 (Additional options to be ordered by additional 9) 5
ordering code)
Modbus RS 232 (Additional options not requested) 10) N
Modbus RS 232 (Additional options to be ordered by additional 9) 6
ordering code)

Additional ordering information

267CS , 269CS Code
Vent valve material / Position
AISI 316L SST (1.4404) On process axis NACE V1
AISI 316L SST (1.4404) On flanges side top NACE V2
AISI 316L SST (1.4404) On flanges side bottom NACE V3
Hastelloy C-276 On process axis NACE V4
Hastelloy C-276 On flanges side top NACE V5
Hastelloy C-276 On flanges side bottom NACE V6
Monel 400 On process axis NACE V7
Monel 400 On flanges side top NACE V8
Monel 400 On flanges side bottom NACE V9

Continued on next page

6) Not available with FM, CSA
7) Not available with EEx nL, EEx d, FM, CSA (select connector type with additional ordering code)
8) Not available with EEx nL, EEx d, FM- / CSA- / NEPSI-Explosion Proof (select connector type with additional ordering code)
9) Additional options to be ordered by additional ordering code
10) Additional options not requested / Not available for electrical connection with connector

16
Series 2600T Pressure Transmitters SS/267CS/269CS
Model 267CS/269CS Multivariable

Additional ordering information

267CS , 269CS Code
Explosion protection
ATEX Group II Category 1/2 GD - Intrinsic Safety EEx ia E1
ATEX Group II Category 1/2 G - Flameproof EEx d E2
ATEX Group II Category 3 GD - Type of Protection N EEx nL Energy Limited E3
IECEx ia Ga / Gb, IECEx iaD 20 E8
IECEx d E9
ATEX II 1/2 GD EEx ia + ATEX II 1/2 GD EEx d + ATEX EEx nL EW
Factory Mutual (FM) - Intrinsically Safe EA
Factory Mutual (FM) - Explosion-proof 11) EB
Canadian Standard Association - Explosion Proof EE
Canadian Standard Association - Explosion Proof (Canada & USA) EM
NEPSI Ex ia II C T4/T6 EY
NEPSI Ex d II C T6 EZ
GOST Russia - EEx ia W1
GOST Russia - EEx d W2
GOST Kazakhstan - EEx ia W3
GOST Kazakhstan - EEx d W4
GOST Ukraine - EEx ia WA
GOST Ukraine - EEx d WB
GOST Belarus - EEx ia WG
GOST Belarus - EEx d WL
SAA Ex d IIC T6 and Ex td A21 IP 66 T85 °C X1
Integrated digital display (LCD)
With integrated LCD display L1
With integrated LCD display (backlit) L2
Mounting bracket shape / Material
For pipe mounting AISI 304 SST (1.4301) B2
For wall mounting AISI 304 SST (1.4301) B4
Operating manual
German M1
French M4
English M5
Russian MB
Label and Tag Language
German Stainless steel 12) T1
German and English Plastic 13) TA
Additional tag plate
Stainless steel (laser printed) I1
Applications
Oil- and grease-free, for oxygen applications (O 2) 14) P1
(Pmax = 12 MPa / 120 bar / 1740 psi, Tmax = 60 °C / 140 °F)
Hydrogen Application (H2) (Fluid Film) P2
Housing Accessories
Integral mount manifold (Price adder just for assembling, not for manifold) A1
Four-wire add-on unit: Power supply 24 V UC / Output signal 0 ... 20 mA A4
Four-wire add-on unit: Power supply 24 V UC / Output signal 4 ... 20 mA A6
Four-wire add-on unit: Power supply 230 V AC / Output signal 0 ... 20 mA A5
Four-wire add-on unit: Power supply 230 V AC / Output signal 4 ... 20 mA A7
Plug upside welded A8
Plug bottom welded A9

Continued on next page

11) Only with Electrical Connection 1/2-14 NPT and Stainless Steel Tag Plate
12) Not available with DIN Electronic Housing code J, K, W
13) Not available with Factory Mutual - Explosion Proof
14) Only available with inert fill and with Viton gasket

17
Series 2600T Pressure Transmitters SS/267CS/269CS
Model 267CS/269CS Multivariable

Additional ordering information

267CS , 269CS Code
Connectors
Fieldbus 7/8 in. (without mating plug, recommended for FOUNDATION fieldbus) U1
Fieldbus M12 x 1 (without mating plug, recommended for PROFIBUS PA) U2
Harting Han 8D (8U) - Straight entry U3
Harting Han 8D (8U) - Angle entry U4
Harting Han 7D U5
Harting Han 8D (8U) - For four-wire add-on unit U6
Harting Han 7D - For four-wire add-on Unit U7
Material traceability
Certificate of compliance with the order 2.1 acc. EN 10204 for process wetted parts H1
Inspection certificate 3.1 acc. EN 10204 of process wetted parts 15) H3
Test report 2.2 acc. EN 10204 of the pressure bearing and process wetted parts H4
Certificates
Inspection certificate 3.1 acc. EN 10204 of calibration C1
Inspection certificate 3.1 acc. EN 10204 of cleanliness stage C3
Inspection certificate 3.1 acc. EN 10204 of helium leakage test of the sensor module C4
Inspection certificate 3.1 acc. EN 10204 of pressure test C5
Declaration of compliance with the order 2.1 acc. EN 10204 for instrument design C6
Calibration record CB
Separate calibration record CC
SIL2 - Declaration of Conformity CL
GOST Russia - Without Explosion Protection WC
GOST Kazakhstan - Without Explosion Protection WD
GOST Ukraine - Without Explosion Protection WE
GOST Belarus - Without Explosion Protection WF

15) Minor parts with factory certificate acc. EN 10204

18
Series 2600T Pressure Transmitters SS/267CS/269CS
Model 267CS/269CS Multivariable

Standard delivery items (changes possible by an additional ordering code)

– Adapters supplied singly
– Plugs for process axis (no drain/vent valves)
– General purpose (no Ex application)
– No display, no mounting bracket
– English-language manual and labels
– Type plate material: barrel electronics housing code A, B, E, G, S, T – stainless steel
DIN electronics housing code J, K, W – plastic
– Configuration with kPa and °C units
– No test, inspection or material certificates

Important remark for all models

The selection of suitable wetted parts and filling fluid for compatibility with the process media is a customers responsibility, if not otherwise notified
before manufacturing.

NACE compliance information

1. The materials of constructions comply with metallurgical recommendations of NACE MR0175/ISO 15156 for sour oil field production
environments. As specific environmental limits may apply to certain materials, please consult latest standard for further details. Materials AISI 316 /
AISI 316L, Hastelloy C-276, Monel 400 also conform to NACE MR0103 for sour refining environments.

2. NACE MR0175 addresses bolting requirements in two classes:

– Exposed bolts: bolts directly exposed to the sour environment or buried, encapsulated or anyway not exposed to atmosphere
– Non exposed bolts: the bolting must not be directly exposed to sour environments, and must be directly exposed to the atmosphere at all
times.

267CS, 269CS bolting identified by “NACE” are in compliance to the requirements of NACE MR0175 when considered “non exposed bolting”

Trademarks
TM
Hastelloy is a trademark of Cabot Corporation
TM
Monel is a trademark of International Nickel Corporation
TM Viton is a trademark of DuPont Dow Elastomers

19
Contact us

ABB Ltd. Note

SS/267CS/269CS-EN Rev. 01 05.2013

We reserve the right to make technical changes or
Process Automation
modify the contents of this document without prior
Howard Road, St. Neots notice. With regard to purchase orders, the agreed
Cambridgeshire, PE19 8EU particulars shall prevail. ABB does not accept any
UK responsibility whatsoever for potential errors or
possible lack of information in this document.
Phone: +44 (0)1480 475321
Fax: +44 (0)1480 217948 We reserve all rights in this document and in the
subject matter and illustrations contained therein.
ABB Inc. Any reproduction, disclosure to third parties or
utilization of its contents – in whole or in parts – is
Process Automation
forbidden without prior written consent of ABB.
125 E. County Line Road
Warminster PA 18974 Copyright© 2013 ABB
USA All rights reserved
Phone: +1 215 674 6000
3KXP400001R1001
Fax: +1 215 674 7183

ABB Automation Products GmbH

Process Automation
Schillerstr. 72
32425 Minden
Sales
Germany
Phone: +49 551 905-534
Fax: +49 551 905-555

www.abb.com
Service

Software