Dual Band WLAN Adapter

WLU5022(RoHS) Quick Setup Guide

v0.2

Askey Computer Corp. WLU5022(RoHS)

Features
z Compatible with IEEE802.11a/b/g/n
z Supports USB 2.0

How to use this Dual Band WLAN Adapter

Turn on the power of the Host device. (For example, TV or printer or other
mobile device) Choose “PREFERENCES” → “Network Setup” → “ Easy
Setup” → “WPS Configuration” → select “PBC” → “Push WPS button on
your AP” → complete wireless configuration → quit the setup menu →
launch internet application
(Please refer to the user manuals of your Host device and AP for more
details.)

Important notice
Please review / study WLU5022(RoHS) Regulatory Statement to avoid
non-legal use of this product.
 Federal Communication Commission Interference Statement

This equipment has been tested and found to comply with the limits for a Class B digital device,
pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable
protection against harmful interference in a residential installation. This equipment generates,
uses and can radiate radio frequency energy and, if not installed and used in accordance with
the instructions, may cause harmful interference to radio communications. However, there is
no guarantee that interference will not occur in a particular installation. If this equipment does
cause harmful interference to radio or television reception, which can be determined by turning
the equipment off and on, the user is encouraged to try to correct the interference by one of the
following measures:
z Reorient or relocate the receiving antenna.
z Increase the separation between the equipment and receiver.
z Connect the equipment into an outlet on a circuit different from that to which the receiver
is connected.
z Consult the dealer or an experienced radio/TV technician for help.

This device complies with Part 15 of the FCC Rules.

Operation is subject to the following two conditions: (1) This device may not cause harmful
interference, and (2) this device must accept any interference received, including interference
that may cause undesired operation.

FCC Caution: Any changes or modifications not expressly approved by the party responsible
for compliance could void the user's authority to operate this equipment.
This device is restricted to indoor use when operated in the 5.15 to 5.25 GHz frequency range.

FCC/IC Radiation Exposure Statement:

This equipment complies with FCC/IC RSS-102 radiation exposure limits set forth for an
uncontrolled environment. This equipment should be installed and operated with minimum
distance 20cm between the radiator & your body.
This device and its antenna(s) must not be co-located or operating in conjunction with any
other antenna or transmitter.

This Class [B] digital apparatus complies with Canadian ICES-003.

Cet appareil numérique de la classe [B] est conforme à la norme NMB-003 du Canada.

FCC
IMPORTANT NOTE:

This module is intended for OEM integrator only and limited to host which can only work with mobile

device. (For example, TV or printer or other mobile device). The OEM integrator is still responsible for the

FCC compliance requirement of the end product, which integrates this module.
20cm minimum distance has to be able to be maintained between the antenna and the users for the host

this module is integrated into. Under such configuration, the FCC radiation exposure limits set forth for an

population/uncontrolled environment can be satisfied.

Any changes or modifications not expressly approved by the manufacturer could void the user's authority

to operate this equipment.

USERS MANUAL OF THE END PRODUCT:

In the users manual of the end product, the end user has to be informed to keep at least 20cm separation

with the antenna while this end product is installed and operated. The end user has to be informed that

the FCC radio-frequency exposure guidelines for an uncontrolled environment can be satisfied. The end

user has to also be informed that any changes or modifications not expressly approved by the

manufacturer could void the user's authority to operate this equipment.

LABEL OF THE END PRODUCT:

The final end product must be labeled in a visible area with the following " Contains TX FCC ID:

H8N-WLU5022 ". The FCC part 15.19 statement below has to also be available on the label: This
device complies with Part 15 of FCC rules. Operation is subject to the following two conditions: (1) this

device may not cause harmful interference and (2) this device must accept any interference received,

including interference that may cause undesired operation.

Industry Canada
OEM integrator is still responsible for testing their end product for any additional compliance
requirements required with this module installed (for example, digital device emissions, PC
peripheral requirements, etc.).
IMPORTANT NOTE: In the event that these conditions can not be met (for example certain
laptop configurations or co-location with another transmitter), then the IC authorization is no
longer considered valid and the IC No. can not be used on the final product. In these
circumstances, the OEM integrator will be responsible for re-evaluating the end product
(including the transmitter) and obtaining a separate IC authorization.
End Product Labeling
This transmitter module is authorized only for use in device where the antenna may be
installed such that 20 cm may be maintained between the antenna and users. The final end
product must be labeled in a visible area with the following: “Contains TX IC:
1353A-WLU5022”.