www.estudentzone.
com
www.estudentzone.com
I.E.S. (Conv.) - 2006
1. ELECTRICAL ENGINEERING
PAPER - II
Time Allowed: 3 Hours Maximum Marks: 200
Candidates should attempt FIVE questions in all. Question No. 1 is compulsory. The remaining Four question are
to be attempted by selecting at least ONE question from each of the Sections A, B, C and D. Assume suitable data,
if necessary and indicate the same clearly.
1. (A) Choose and write the correct answer IC) x 2 = 21)
(a) A 220 V D.C. machine has an armature resistance I. If the full-load current is 20 A, the
difference in induced voltage when the machine is running as a motor, and as a generator is
(i) 20V (ii) 0V
(iii) 40 V (iv) 60 V
(b) A 4-pole, 50 Hz, 3 phase induction motor has blocked rotor reactance per phase which is four
times the rotor resistance per phase. The speed at which maximum torque develops is
(i) 1125 rpm
(ii) 1500 rpm
(iii) 1050 rpm
(iv) 1210 rpm
(c) In load flow studies of a power system, a voltage control bus is specified by
(i) Real power and reactive power
(ii) Reactive power and voltage magnitude
(iii) Voltage and voltage phase angle
(iv) Real power and voltage magnitude
(d) Which of the following circuit breakers is generally used in railway electrification?
(i) Air blast circuit breaker
(ii) Minimum oil circuit breaker
(iii) Bulk oil circuit breaker
(iv) SF6 circuit breaker
(e) The output frequency of a decade counter that is clocked from a 50 kl-Iz signal is
(i) 12.5 kHz (ii) 50 kHz
(iii) 5 kHz (iv) 500 kHz
(f) When two amplifiers each of bandwidth, fH = 10kHz are cascaded, the overall bandwidth
becomes
(i) 10 kHz (ii) 6.4 kHz
(iii) 5 kHz (iv) 20 kHz
(g) The ______ instruction allows control to transfer to a subroutine, which when complete, issue
the _____ instruction to return control to the main programe.
(i) CALL, JMP (ii) CALL, RET
(iii) CALL, RSTI (iv) El, Dl
www.estudentzone.com
www.estudentzone.com
(h) One of the advantages of base modulation over collector modulation of a transistor Class C
amplifier is
(i) the lower modulating power required
(ii) higher power output per transistor
(iv) better efficiency
(v) better linearity
(i) Which of the following configurations is used for both motoring and regenerative breaking?
(i) First quadrant chopper
(ii) Second quadrant chopper
(iii) Two quadrant chopper
(iv) Four quadrant chopper
(j) In ac applications, a different measure of harmonics is needed. The total harmonic ratio
(THR) is given by:
2
f rms f12rms
(i)
f rms
2
f rms f1rms
(ii)
f12rms
f12rms f1rms
(iii)
f rms
f12rms f rms
(iv)
f1rms
(B) (a) What are the methods of starting of synchronous motors?
4
(b) Explain the limits of AC transmission lines.
4
(c) A symmetrical 5 kHz square wave whose output varies between + 10 V and -10 V is
impressed upon the clipping circuit shown. Assume Rf = 0, R = 2 M and V = 0. Sketch the
steady state waveform indicating numerical values of the maximum, minimum and constant
portion.
4
(d) Explain RIM and SIM instructions of 8085 microprocessor, with accumulator data format.
4
(e) A 100/1 A bar primary current transformer supplies an over current relay setting at 50% pick
up and it has a burden of 2 VA. Determine the knee point voltage and cross section of the
core if the CT has 50 turns on its secondary and the fault current is 15 times the relay setting.
Assume the flux density as 1.4 Wb/M2 and frequency = 50 Hz.
www.estudentzone.com
www.estudentzone.com
4
SECTION A
2. (A) A 1500 kVA, 6.6/1.1 kV, 3 phase delta-star connected transformer has the following test
result:
S.C. test: (Instruments placed on h.v. side)
300 V, 131.21 A, 30 kw
Calculate its percentage resistance, percentage reactance drops, percentage efficiency and
percentage regulation on full load at 0.8 power factor lagging. The iron loss during O.C. test
with rated voltage supplied is 25 kW.
14
(b) A star-connected 3-phase alternator delivers a 3-phase star- connected load at a power factor
of 0.8 lagging. A wire connects the load and the alternator. The terminal voltage at no-load is
2500 V, and at full-load of 1460 kW it is 2200 V. Determine the terminal voltage when it
delivers a 3 phase star-connected load having a resistance of 6 Q and reactance 8 (2 per phase
respectively. Assume constant current and field excitation.
14
(c) (i) Interpret the following instructions and mention their addressing mode and flag
affected, if any
XRA A; DAA; DCR M; ADD B.
8
(ii) What is the difference between Accumulator (ACC) and Instruction Register (IR)?
4
3. (a) (i) With connection diagrams for both shunt and separately excited D.C. generators, draw
the important characteristics of these generators.
6
(ii) Calculate the rms value of the induced emf per phase of a 10 pole, three phase, 50 Hz
alternator with 2 slots per pole per phase and 4 conductors per slot in two layers. The
coil span is 150°. The flux per pole is 0.12 wb.
8
(b) Two alternators working in parallel supply a lighting load of 3000 kW and a motor load
aggregating to 5000 kW at a p.1 of 0.72. One machine is loaded up to 5000 kW at 0.8 p.f.
lagging. What is the load and power factor of the other machine?
14
(c) Consider a two stage synchronous counter (both stages receive the pulses at the CK input). In
each counter K = 1. If Q 1 and J1 Q0, draw the circuit. From a truth table of Q0 and Q1 after
each pulse, demonstrate that this is a 3 : 1 counter.
12
SECTION B
4. (a) A two-machine power system delivers a load of 25 MW at 0.8 p.f. lag and has a double
circuit. The system reactance is 150 percent on 100 MVA base. A sudden symmetrical line-
to-ground fault occurs in one of the circuits which reduced the power supplied to 40% which
is subsequently cleared by simultaneous action of the circuit breakers on both sides of the
faulted line. Calculate in the electrical degrees the “critical clearing angle”. Assume that
during fault conditions the system reactance attains such a value that the maximum power
becomes 30% of the normal maximum value, when the faulty line is isolated the maximum
power of the system becomes 60% of the normal maximum power.
www.estudentzone.com
www.estudentzone.com
14
(b) For a certain industrial organization the maximum and minimum power demands are 50 MW
and 10 MW respectively. Its load duration curve can be approximated as shown in Fig. 4. (b),
below. The hydro power available at the time of minimum regulated flow is just sufficient to
take a peak load of 60 MWh per day. Further, it is observed that it will be economical to
pump water form tail race to the reservoir tank by utilizing the steam power plant during off
peak periods and thus running the station at 100 per cent load factor. If the efficiency of the
steam electric conversion is 60%, calculate the maximum capacity of each type of plant.
14
(c) A BCD number between 0 and 99 is stored in an RI’W memory location called the input
Buffer. Write a main program & a conversion subroutine (BCDBTN) to convert the BCD
number into its equivalent binary number in 8085. Store the result in a memory location
defined as Output Buffer.
12
5. (a) What do you understand by Ferranti effect?
Determine the sending end voltage and efficiency by method of a line, given resistance of
line (R = 0.2 × 120 = 24), inductive reactance (XL = 48.98 ) and capacitance reactive (XC
= 1.2).
14
(b) Two generating stations having short-circuit capacities of 1200 MVA and 800. MVA
respectively and operating at 11 kV are linked by an interconnected cable having reactance of
0.5 ohm per phase. Determine the short-circuit capacity of each station.
14
(c) (i) Explain Foster-Seeley discriminator with neat circuit diagram and waveforms.
6
(ii) When the modulating frequency in FM system is 400 Hz and the modulating voltage
is 2.4 V, the modulation index is 60. Calculate the maximum index, when the
modulating frequency is reduced to 250 Hz & the modulating voltage is
simultaneously raised to 3.2 V?
6
SECTION C
6. (a) Consider the circuit shown below. Let VCC = 5 V, RC = 1 k, V(BE(ON) = 0.7 V and = 120.
Choose R and determine R1 and R2 such that the circuit is bias stable and that VCEQ = 3V.
14
www.estudentzone.com
www.estudentzone.com
(b) The waveforms
are applied to the inputs of the latch
Draw the waveform at Q and explain.
14
(c) (i) List the major factors influencing the choice of the intermediate frequency (IF) in any
particular system.
6
(ii) Which are frequencies band for AM, SW and FM broadcast system? Mention the IF
values for these systems.
6
7. (a) (i) How sigma-delta modulation system is developed from delta modulation? Explain
with block schematic.
8
(ii) A PCM system is to have SNR of 42.93 dB. The signals ate speech, and an rms to
peak ratio of-10 dB is allowed for. Find the number of bits per code word required.
6
(b) (i) Justify that frequency modulation is much more immune to noise than amplitude
modulation.
(ii) Sketch the typical IF, characters response for colour TV receiver. Indicate frequency
and signal levels on curve.
6
(c) Consider the idealized push-pull Class B power amplifier as shown below:
www.estudentzone.com
www.estudentzone.com
Give that R2 = 0, VCC = 20 V, N2 = 2 N1, RL = 20 and the transistors have hFE = 20. The
input is a sinusoid. For the maximum output signal at Vm = VCC, determine:
(i) the output signal power.
(ii) the collector dissipation in each transistor.
12
SECTION D
8. (a) The buck regulator in Fig. 8 (a) shown has an input voltage of Vs = 12 V. The required
average output voltage is Va = 5 V at R = 500 and the peak-to-peak output ripple voltage is
20 mV. The switching frequency is 25 kHz. If the peak-to-peak ripple current of inductor is
limited to 0.8 A, determine
(i) the duty cycle K,
(ii) the filter inductance L,
(iii) the filter capacitor C and
(iv) the critical value of L and C.
Fig. 8 (a) : Circuit diagram
(b) (i) Explain the transfer characteristics of n-channel and p-channel MOSFETS along with
their output characteristics of an n-channel enhancement MOSFEE
8
(ii) The bipolar transistor in Fig. 8 (b) is specified to have F in the range of 8 to 40. The
load resistance is RC = 11 ohm. The d.c. supply voltage is = 200 V and the input
voltage to the base circuit is VB = 10 V. If VCL(sat) = 1.0 V and VBE(sat) = 1.5V, find
(1) the value of RB that results in saturation with an ODF of 5
(2) the forced, and
(3) the power loss PT in the transistor.
6
www.estudentzone.com
www.estudentzone.com
Fig. 8 (b): Transistor Switch
(c) An 8085-8155 based microcomputer is required to drive an LED connected to bit 0 of port A
based on two switches inputs connected to bits 6 and 7 of port A. If both switches are either
High or Low, turn the LED ON; otherwise turn it OFF. Assume that HIGH will turn the LED
ON and that a ow will turn it OFF. Use port address of CSR and Port A as 20 H and 21 H,
respectively. Program starts from 2000 H. Write an 8085 assembly language program.
12
9. (a) Point out the differences between latching current and hold current for the thyristor. What do
you understand by string efficient related to thyristors? For a thyristor, maximum junction
temperature is 125°C. The thermal resistances for thyristor-sink combination are jc = 0.16
and cs = 0.08°C/W. For a heat-sink temperature of 70°C, compute the total average power
loss in the thyristor sink combination. In case the heat sink is brought down to 60°C by forted
cooling, find the percentage increase in the device rating.
14
(b) A voltage source Inverter is to be used for a backup power application. This unit, shown in
Fig. 9 (b), draws power from a set of lead-acid batteries with nominal output of 144 V and
supplies upto 2 kW into a load. A resonant filter is to be used to provide an output sinusoidal
at 120 Vrms, 60 Hz with THD < 3% at hill load. If the actual battery voltage will vary between
132 V and 156 V, what range of values will be used for this application? Select a series L-C
pair to meet the requirements ( - is the trigging angle). Utility supply variation ±5%. Assume
only third harmonic is present.
(c) Derive the following for the 3 phase induction motor due to interaction of rotor and stator
fields:-
(i) Torque developed
(ii) Starting torque.
(iii) Condition for maximum torque.
(iv) Effect of change in supply voltage on starting torque.
(v) Effect of change in supply voltage on torque and slip.
(vi) Full load torque and maximum torque.
12
