INTERNATIONAL IEC

STANDARD 60044-7
First edition
1999-12

Instrument transformers –

Part 7:
Electronic voltage transformers

This English-language version is derived from the original

bilingual publication by leaving out all French-language
pages. Missing page numbers correspond to the French-
language pages.

Reference number
IEC 60044-7:1999(E)
INTERNATIONAL IEC
STANDARD 60044-7
First edition
1999-12

Instrument transformers –

Part 7:
Electronic voltage transformers

 IEC 1999 Copyright - all rights reserved

No part of this publication may be reproduced or utilized in any form or by any means, electronic or mechanical,
including photocopying and microfilm, without permission in writing from the publisher.

International Electrotechnical Commission, 3, rue de Varembé, PO Box 131, CH-1211 Geneva 20, Switzerland
Telephone: +41 22 919 02 11 Telefax: +41 22 919 03 00 E-mail: [email protected] Web: www.iec.ch

Commission Electrotechnique Internationale

International Electrotechnical Com m ission
PRICE CODE XB
Международная Электротехническая Комиссия
For price, see current catalogue
60044-7 © IEC:1999 –3–

CONTENTS
Page
FOREWORD .......................................................................................................................... 7

Clause
1 General............................................................................................................................ 9
1.1 Scope ..................................................................................................................... 9
1.2 Normative references.............................................................................................. 9
1.3 General block diagram of electronic voltage transformers ..................................... 13
2 Definitions...................................................................................................................... 15
2.1 General definitions................................................................................................ 15
2.2 Additional definitions for single-phase electronic protective voltage
transformers ......................................................................................................... 27
2.3 Index of symbols ................................................................................................... 27
3 General requirements .................................................................................................... 31
3.1 General................................................................................................................. 29
3.2 Information to be given for enquiries, tenders and orders...................................... 31
4 Normal and special service conditions ........................................................................... 31
4.1 Normal service conditions ..................................................................................... 31
4.2 Special service conditions..................................................................................... 35
4.3 Earthing system .................................................................................................... 37
5 Ratings .......................................................................................................................... 37
5.1 Standard values of rated voltages ......................................................................... 37
5.2 Standard values of rated output ............................................................................ 39
5.3 Standard values of rated voltage factor ................................................................. 39
5.4 Standard values of rated auxiliary power supply voltage ....................................... 41
5.5 Standard reference values of other influencing parameters ................................... 41
6 Design requirements ...................................................................................................... 43
6.1 Insulation requirements for primary voltage sensor ............................................... 43
6.2 Insulation requirements for low-voltage components ............................................. 51
6.3 Short-circuit withstand capability........................................................................... 53
6.4 Limits of temperature rise ..................................................................................... 53
6.5 Radio interference voltage requirements ............................................................... 53
6.6 Transmitted overvoltage requirements .................................................................. 55
6.7 Electromagnetic compatibility requirements .......................................................... 55
6.8 Reliability.............................................................................................................. 59
6.9 Abnormal conditions withstand capability .............................................................. 61
6.10 Abnormal conditions signalling.............................................................................. 61
6.11 Mechanical requirements ...................................................................................... 61
6.12 Earthing terminals................................................................................................. 63
7 Classification of tests ..................................................................................................... 63
7.1 Type tests ............................................................................................................. 63
7.2 Routine tests ........................................................................................................ 65
7.3 Special tests ......................................................................................................... 65
60044-7 © IEC:1999 –5–

Clause Page
8 Type tests ...................................................................................................................... 65
8.1 Impulse test on primary voltage terminals ............................................................. 65
8.2 Wet test for outdoor type electronic voltage transformers...................................... 69
8.3 Tests for accuracy ................................................................................................ 69
8.4 Test for abnormal conditions withstand capability ................................................. 71
8.5 Radio interference voltage test ............................................................................. 73
8.6 Transmitted overvoltage test ................................................................................. 73
8.7 Electromagnetic compatibility tests ....................................................................... 73
8.8 Impulse voltage withstand test for low-voltage components .................................. 79
8.9 Transient performance tests ................................................................................. 81
9 Routine tests.................................................................................................................. 81
9.1 Verification of terminal markings ........................................................................... 81
9.2 Power-frequency withstand tests on primary voltage terminals
and partial discharge measurement ...................................................................... 81
9.3 Power-frequency voltage withstand test for low-voltage components .................... 85
9.4 Tests for accuracy ................................................................................................ 87
10 Special tests .................................................................................................................. 87
10.1 Chopped lightning-impulse test on primary voltage terminals ................................ 87
10.2 Measurement of capacitance and dielectric dissipation factor ............................... 89
10.3 Mechanical strength tests ..................................................................................... 89
11 Markings ........................................................................................................................ 91
11.1 Rating plate markings ........................................................................................... 91
11.2 Terminal markings ................................................................................................ 95
12 Accuracy requirements for single-phase electronic measuring voltage transformers....... 95
12.1 General requirements ........................................................................................... 95
12.2 Maintenance requirement...................................................................................... 97
12.3 Accuracy class designation for electronic measuring voltage transformers ............ 97
12.4 Standard accuracy classes for electronic measuring voltage transformers ............ 97
12.5 Limits of voltage error and phase displacement for electronic measuring
voltage transformers ............................................................................................. 99
13 Additional requirements for single-phase electronic protective voltage transformers ...... 99
13.1 General requirements ........................................................................................... 99
13.2 Maintenance requirements .................................................................................. 101
13.3 Accuracy class designation for electronic protective voltage transformers........... 101
13.4 Standard accuracy classes for electronic protective voltage transformers ........... 101
13.5 Limits of voltage error and phase displacement for electronic protective
voltage transformers ........................................................................................... 101
13.6 Transient performance requirements................................................................... 103

Annex A (normative) Burdens for the transient response test ............................................. 105
Annex B (informative) Technical information for electronic voltage transformers................. 109
Annex C (informative) Bibliography .................................................................................... 137
60044-7 © IEC:1999 –7–

INTERNATIONAL ELECTROTECHNICAL COMMISSION

____________

INSTRUMENT TRANSFORMERS –

Part 7: Electronic voltage transformers

FOREWORD
1) The IEC (International Electrotechnical Commission) is a worldwide organization for standardization comprising
all national electrotechnical committees (IEC National Committees). The object of the IEC is to promote
international co-operation on all questions concerning standardization in the electrical and electronic fields. To
this end and in addition to other activities, the IEC publishes International Standards. Their preparation is
entrusted to technical committees; any IEC National Committee interested in the subject dealt with may
participate in this preparatory work. International, governmental and non-governmental organizations liaising
with the IEC also participate in this preparation. The IEC collaborates closely with the International
Organization for Standardization (ISO) in accordance with conditions determined by agreement between the
two organizations.
2) The formal decisions or agreements of the IEC on technical matters express, as nearly as possible, an
international consensus of opinion on the relevant subjects since each technical committee has representation
from all interested National Committees.
3) The documents produced have the form of recommendations for international use and are published in the form
of standards, technical reports or guides and they are accepted by the National Committees in that sense.
4) In order to promote international unification, IEC National Committees undertake to apply IEC International
Standards transparently to the maximum extent possible in their national and regional standards. Any
divergence between the IEC Standard and the corresponding national or regional standard shall be clearly
indicated in the latter.
5) The IEC provides no marking procedure to indicate its approval and cannot be rendered responsible for any
equipment declared to be in conformity with one of its standards.
6) Attention is drawn to the possibility that some of the elements of this International Standard may be the subject
of patent rights. The IEC shall not be held responsible for identifying any or all such patent rights.

International Standard IEC 60044-7 has been prepared by IEC technical committee 38:
Instrument transformers

The text of this standard is based on the following documents:

FDIS Report on voting

38/242/FDIS 38/243/RVD

Full information on the voting for the approval of this standard can be found in the report on
voting indicated in the above table.

This publication has been drafted in accordance with the ISO/IEC Directives, Part 3.

The committee has decided that this publication remains valid until 2002. At this date, in
accordance with the committee's decision, the publication will be

• reconfirmed;
• withdrawn;
• replaced by a revised edition; or
• amended.
60044-7 © IEC:1999 –9–

INSTRUMENT TRANSFORMERS –

Part 7: Electronic voltage transformers

1 General

1.1 Scope

This part of International Standard IEC 60044 applies to newly manufactured electronic
voltage transformers with analogue output, for use with electrical measuring instruments and
electrical protective devices at frequencies from 15 Hz to 100 Hz.
NOTE 1 Optical arrangements usually include electronic components and are therefore considered to be within
the application of this standard.
NOTE 2 Detailed information is given in annex B.
NOTE 3 Requirements specific to three-phase voltage transformers are not included in this standard but, so far as
they are relevant, the requirements in clauses 3 to 11 apply to these transformers and a few references to them are
included in those clauses (e.g. see 2.1.5, 5.1.1, 5.2, 11.2.1 and 11.2.2).

1.2 Normative references

The following normative documents contain provisions which, through reference in this text,
constitute provisions of this part of IEC 60044. For dated references, subsequent amend-
ments to, or revisions of, any of these publications do not apply. However, parties to
agreements based on this part of IEC 60044 are encouraged to investigate the possibility of
applying the most recent editions of the normative documents indicated below. For undated
references, the latest edition of the normative document referred to applies. Members of IEC
and ISO maintain registers of currently valid International Standards.

IEC 60038:1983, IEC standard voltages

IEC 60044-2:1997, Instrument transformers – Part 2: Inductive voltage transformers

IEC 60050(161):1990, International Electrotechnical Vocabulary (IEV) – Chapter 161:

Electromagnetic compatibility

IEC 60050(321):1986, International Electrotechnical Vocabulary (IEV) – Chapter 321:

Instrument transformers

IEC 60050(601):1985, International Electrotechnical Vocabulary (IEV) – Chapter 601:

Generation, transmission and distribution of electricity – General

IEC 60050(604):1987, International Electrotechnical Vocabulary (IEV) – Chapter 604:

Generation, transmission and distribution of electricity – Operation

IEC 60060 (all parts), High-voltage techniques

IEC 60060-1:1989, High-voltage test techniques – Part 1: General definitions and test
requirements

IEC 60071-1:1993, Insulation co-ordination – Part 1: Definitions, principles and rules

60044-7 © IEC:1999 – 11 –

IEC 60186:1987, Voltage transformers

IEC 60255-5:1977, Electrical relays – Part 5: Insulation tests for electrical relays

IEC 60255-6:1988, Electrical relays – Part 6: Measuring relays and protection equipment

IEC 60255-11:1979, Electrical relays – Part 11: Interruptions to and alternating component
(ripple) in d.c. auxiliary energizing quantity of measuring relays

IEC 60255-22-1:1988, Electrical relays – Part 22: Electrical disturbance tests for measuring
relays and protection equipment – Section 1: 1 MHz burst disturbance tests

IEC 60270:1981, Partial discharges measurements

IEC 60617-1:1985, Graphical symbols for diagrams – Part 1: General information, general
index. Cross-reference tables

IEC 60694:1996, Common specifications for high-voltage switchgear and controlgear

standards

IEC 60721 (all parts), Classification of environmental conditions

IEC 60815:1986, Guide for the selection of insulators in respect of polluted conditions

IEC 61000 (all parts), Electromagnetic compatibility (EMC)

IEC 61000-4-1:1992, Electromagnetic compatibility (EMC) – Part 4: Testing and measurement

techniques – Section 1: Overview of immunity test. Basic EMC publication

IEC 61000-4-2:1995, Electromagnetic compatibility (EMC) – Part 4: Testing and measurement

techniques – Section 2: Electrostatic discharge immunity test. Basic EMC publication

IEC 61000-4-3:1995, Electromagnetic compatibility (EMC) – Part 4: Testing and measurement

techniques – Section 3: Radiated, radio-frequency, electromagnetic immunity test

IEC 61000-4-4:1995, Electromagnetic compatibility (EMC) – Part 4: Testing and measurement

techniques – Section 4: Electrical fast transient/burst immunity test. Basic EMC publication

IEC 61000-4-5:1995, Electromagnetic compatibility (EMC) – Part 4: Testing and measurement

techniques – Section 5: Surge immunity test

IEC 61000-4-8:1993, Electromagnetic compatibility (EMC) – Part 4: Testing and measurement

techniques – Section 8: Power frequency magnetic field immunity test. Basic EMC publication

IEC 61000-4-9:1993, Electromagnetic compatibility (EMC) – Part 4: Testing and measurement

techniques – Section 9: Pulse magnetic field immunity test. Basic EMC publication

IEC 61000-4-10:1993, Electromagnetic compatibility (EMC) – Part 4: Testing and

measurement techniques – Section 10: Damped oscillatory magnetic field immunity test.
Basic EMC publication
60044-7 © IEC:1999 – 13 –

IEC 61000-4-11:1994, Electromagnetic compatibility (EMC) – Part 4: Testing and

measurement techniques – Section 11: Voltage dips, short interruption and voltage variation
immunity test

IEC 61000-4-12:1995, Electromagnetic compatibility (EMC) – Part 4: Testing and

measurement techniques – Section 12: Oscillatory waves immunity tests. Basic EMC
publication

CISPR 11 (EN 55011), Industrial, scientific and medical (ISM) radio-frequency equipment –
Electromagnetic disturbance characteristics – Limits and methods of measurement

EN 50081-2:1993, Electromagnetic compatibility – Generic immunity standard – Part 2:

Industrial environment

1.3 General block diagram of electronic voltage transformers

The applied technology decides which parts are necessary for realisation of an electronic
voltage transformer, i.e. it is not absolutely essential that all parts described be in the
transformer (see figures 1 and 2).

A Primary a
voltage Primary Transmitting Secondary
sensor converter system converter
N n

Primary voltage Secondary voltage

terminals terminals

Primary Secondary
power power
supply supply

IEC 1192/99

Figure 1 – General block diagram of earthed single-phase electronic voltage transformers

A Primary a
voltage
sensor
N n

B Primary b
Primary Secondary
voltage Transmitting
converter converter
sensor system
N n

C Primary c
voltage
sensor
N n

Primary voltage Secondary voltage

terminals terminals

Primary Secondary
power power
supply supply

IEC 1193/99

Figure 2 – General block diagram of earthed three-phase electronic voltage transformers