College of Engineering, Pune

(An Autonomous Institute of Govt. of Maharashtra, Permanently Affiliated to S.P. Pune University)

Department of Mechanical Engineering

Curriculum Structure & Detailed Syllabus (UG Program)

Second Year B.Tech.

(Revision: A.Y. 2015-16, Effective from: A.Y. 2016-17)

INDEX

Sr.
Item Page No
No.
1 UG Program: Rules and Regulations 2

2 Program Education Objectives (PEOs) and Program Outcomes (POs) 23

3 Correlation between PEOs and POs 24

4 List of Abbreviations 25

5 Curriculum Structure & Detailed Syllabi 26

.
1
 UG PROGRAMS
(FOR AWARD of B.TECH.DEGREE)

ACADEMIC RULES and REGULATIONS

1. Short Title a n d Commencement:

(a) These Regulations shall be called the “College of Engineering, Pune Regulations
for the Award of B.Tech. Degree”;
(b) They shall come into effect from the date of getting approval from the Board
of Governors of the College.
(c) They shall be applicable for students enrolling for B. Tech. Degree programmes
at the College from Academic year 2015-16.
2. Definitions:
(a) “B. Tech.” means Bachelor of Technology, an Under Graduate Degree
awarded b y a n d from the University;
(b) “Board” means Board of Governors of the c o llege;
(c) “College” means College of Engineering, Pune;
(d) “Council” means All India Council for Technical
Education;
(e) “Dean” means Dean of the College, with the specific
functions also indicated along with the title;
(f) “Deputy Director” means Deputy Director of the
College;
(g) “Director” means Director of the College;
(h) “Government” means Government of the Maharashtra;
(i) “Prescribed” means prescribed by these or any other
Regulations of the College;
(j) “Regulations” means College of Engineering, Pune
Regulations for the Award of B. Tech. Degree;
(k) “Senate” means Senate of the College;
(l) “University” means S a v i t r i b a i P h u l e P u n e
University
3. Preamble:
The Regulations prescribed herein have been made by the College, an autonomous
institution affiliated to the Savitribai Phule Pune University, to facilitate the smooth
and orderly conduct of its academic programmes and activities at the B. Tech level. It

2
 is expected that the Regulations will enable the students to take advantage of the
various academic opportunities at the College and prepare themselves to face the
challenges in their professional careers ahead. It may be noted that:

(a) The provisions made herein shall be applicable to all the B. Tech. Programmes
offer ed at the College, at present;
(b) They shall also be applicable to all the new B. Tech. Programmes which may be
started at the College in the future;
(c) Academic and non-academic requirements prescribed by the Senate have to be
fulfilled by a student for eligibility to the Award of B.Tech. degree.
4. Academic Calendar:
Table 1 : Suggested Breakdown of Academic Year into Semesters

Three; Two being Main Semesters (Odd and Even) and One
being a Supplementary Semester;
1. No. of (Note: Supplementary Semester is primarily to assist weak
Semesters/ and/or failed students through make up courses, wherever
Year possible. However, the College may use this Semester to
arrange Add -On Courses for other students and/or for
deputing them for practical training elsewhere.)

2. Semester Main Semesters: 19 Weeks each;

Durations: Supplementary Semester: 8 Weeks;
Main Semester (Odd or Even)
Registration of Courses- 0.5; Course w ork- 15.5; Examination
Preparation-1.0; Examinations- 1.0; Declaration of Results-
1.0; Total: 19;
3. Supplementary Semester (only for make up Courses):
Academic Registration of Courses- 0.1; Course Work- 7.0;
Activities Examination Preparation-0.2; Examinations- 0.2; Declaration
(Weeks): of Results- 0.5; Total: 8;
Inter-Semester Recess:
After each Main Semester- 2; After Supplementary Semester-
2;
Total: 14 (for good students) and 6 (for weak students)
(Note: In each Semester, t h e r e shall be provision for
students for Registration of Courses at the beginning,
Dropping of Courses in the middle under the advice of Faculty
Members and approved by Departmental Undergraduate
Programme Committee (DUPC).

3
 Continuous Internal Evaluation (CIE) and Semester End
Examination (ESE), both having equal weightage in the
students‟ performance in Course Work/Laboratory Work and
4. other activities;
Examinations: (Note: The CIE shall be conducted t h ro u g h o u t the
Semester on dates announced in advance by the subject
teacher, and its results made known to the students from
time to time. This would be of help to the students to
decide on Dropping or Withdrawal from Courses in
consultation with their Advisors. However, the dates for the
Mid-Semester E x a m i n a t i o n (MSE) which is a part of the CIE
and ESE shall be fixed at the College level.
• Care shall be taken to ensure that the total number of
days for academic work are > 180/year;
• Academic schedules prescribed shall be strictly adhered to
5. Other by all the Departments;
Items: • Supplementary Semester shall be mainly for Make up
Courses, to benefit weak or failed students to the extent
possible;
• Students failed in a course shall attend a Course fully
when it is offered again, and appear for all components
of evaluation;
• Specified Min. /Max. Course load per Semester shall be
followed at all times.

(a) Each academic year shall be divided into two main semesters, each of 19 weeks,
viz., odd semester (Jul. – Dec.) and even semester (Dec. – Apr.), and an 8-
week supplementary semester (A p r .-Jun.).
(b) The College shall arrange regular academic activities for the students during the
two main semesters and makeup and other courses for the students during the
supplementary semester;
(c) The academic activities in a semester shall normally include course registration,
course work, continuous internal evaluation, dropping/withdrawal from courses,
semester-end examination, and declaration of results.
(d) The College shall announce the schedule for all the academic activities well before the
commencement of the academic year and take all the necessary steps to follow them
scrupulously.
(e) The college shall also announce adequate intra-semester and inter-semester breaks
for the students and ensure that a minimum of 180 academic working days are
available during the academic year.
(f) A typical breakdown of the academic year for the B. Tech programme at the
College shall be as suggested in Table 1:

4
5. Admissions:
(a) The intake capacity of each programme, including the number of seats to be
reserved for students of different categories shall be decided by the Board by following
the Government directives and Council approvals.
(b) Admissions to the first year of all the programmes shall be made before the start of
each academic year, through the Maharashtra Combined Entrance Test (MHCET)
conducted by the Government.
(c) The College shall also admit to first year of the programmes, a limited number
of students of Non-Resident Indian (NRI), Persons of Indian Origin (PIO) and
Foreign National categories, as per Government rules.
(d) There shall also be a merit-based, lateral admission of students having Diploma
qualification to the second year of all the programmes at the College in accordance
with the Government rules applicable for such admissions.
(e) The College reserves the right to revoke the admission made to a candidate, if it is
found at any time after admission that he/she does not fulfill all the requirements
stipulated in the offer of admission.
(f) The College also reserves the right to cancel the admission of any student and
discontinue his/her studies at any stage of studentship for unsatisfactory
academic performance and/or undisciplined conduct.
6. In-campus Residence:
(a) Interested students may apply for hostel accommodation at the time of admissions,
as the College is partially residential and it can admit a limited number of men and
women students in the hostels.
(b) The method of admission to students‟ hostels, rent payable per each seat allotted
and the discipline to be followed by the residents shall be governed by “rules and
regulations” framed by the College in this behalf.
(c) Each student selected for hostel admission shall be provided a seat in one of the hostel
rooms identified for this purpose and there shall be no family accommodation
available in the hostel for married students.
(d) Students residing in the hostels shall adhere to the prescribed hostel discipline and pay
the hostel/mess charges regularly, as any failure to do so, may lead to withdrawal of
hostel facilities to such students.
(e) Hostel residents shall apply for leave of absence and get the same approved before
leaving the hostel even for a few days, as any failure to do so may lead to
cancellation of hostel admission to such students.
(f) Students residing in the hostels shall be required to clear all the hostel dues and
vacate their rooms at the end of each academic year, as they will be considered for
hostel admission afresh for the New Year.

5
7. Attendance:
(a) Each student shall be required to attend at least 75 per cent of all the
classes arranged like, lectures, tutorials, laboratories, studios and workshops for
being permitted to attend the semester-end examination.
(b) Extra Academic Activities (EAC) like Yoga, NSS, Physical Training, NCC and, Boat Club
shall be compulsory for students of the first year, with at least a minimum
attendance o f 75 percent in each of them.
(c) Students shall also be required to take part in any other academic and non-
academic activities and attend the camps, as and when arranged by the College
during the academic year.
(d) Students desirous of leave of absence for less than two weeks during a semester shall
apply for it in advance to the Head of the Department giving reasons & supporting
documents, if any and get it approved.
(e) Absence due to illness or any other reason for a period less than two weeks in a
semester, for which a student could not make prior application, may be condoned
by the Head of the Department after proper verification.
(f) The Dean, Academic Affairs shall be the Authority for sanctioning the leave of
students o u t s i d e clauses (4) and (5) above, after receiving their applications along
with recommendations of the Heads of Departments.
(g) In the case of long absence of a student in a semester with prior approval or
otherwise, the Dean, Academic Affairs shall decide whether the student be asked to
withdraw from the programme for that particular semester.
(h) In all the cases of leave of absence as per Clauses (4)-(6) above, the period of
leave taken shall not be condoned for the purposes of fulfilling the attendance
r e q u i r e m e n t s stipulated in the Clauses (1) and (2).
(i) It shall be the responsibility of a student residing in the hostel to intimate the Warden
of his/her hostel and also the concerned course instructors regarding his/her absence
before proceeding on leave.
8. Code of Conduct and Discipline:
(a) All students shall be required to conduct themselves in a manner befitting the
students of a national institution of high reputation, within and outside the precincts
of the College.
(b) Unsocial activities like ragging in any form shall not be permitted within or outside
the precincts of the College and the students found indulging in them shall be dealt
with severely and dismissed from the College.
(c) The following additional acts of omission and/or c om mi ss io n by the students
within or outside the precincts of the College shall constitute gross violation of code
of conduct punishable as indiscipline:
i. Lack of courtesy and decorum, as well as indecent behaviour;
ii. Willful damage of property of the College/Hostel or of fellow students;
iii. Possession/consumption/distribution of alcoholic drinks and banned drugs;

6
 iv. Mutilation or unauthorized possession of library material, like. books;
v. Noisy and unseemly behaviour, disturbing peace in the College/Hostel;
vi. Hacking in computer systems, either hardware or software or both;
vii. vii. Any other act considered by the College as of gross indiscipline.

(d) In each case above, the punishment shall be based on the gravity of offence, covering
from reprimand, levy of fine, expulsion from Hostel, debar from examination,
rustication for a period, to outright expulsion.
(e) The reprimanding Authority for an offence committed by students in the Hostels and in
the Department or the classroom shall be respectively, the Rector of the Hostels
and the Head of the concerned Department.
(f) In all the cases of offence committed by students in jurisdictions outside the purview
of Clause (5), the Dean, Students Affairs shall be the Authority to reprimand them.
(g) All major acts of indiscipline involving punishment other than mere reprimand, shall be
considered and decided by the Chairman, Students Disciplinary Committee appointed
by the Senate.
(h) All other cases of indiscipline of students, like adoption of unfair means in the
examinations shall be reported to the Dean, Academic Affairs, for taking appropriate
action and deciding on the punishment to be levied.
(i) In all the cases of punishment levied on the students for any offence committed, the
aggrieved party shall have the right to appeal to the Director, who shall constitute
appropriate Committees to review the case.
9. Change of Branch:
(a) Change of branch shall be permissible for a limited number of special cases in the
third semester as per following regulations.
(b) Only those students who have completed the common credits required in the first
two semesters in their first attempt w i t h a minimum CGPA of 8.5 shall only be
eligible for making application for a change of branch.
(c) There shall be a maximum number of only two students admitted in any discipline in
the third semester through the branch change rule.
(d) Intending students eligible for change of branch shall apply for the same to the
Office of Academic Affairs of the College before the closing date notified at the
beginning of odd semester of each academic year.
(e) Such students shall be required to indicate up to three branches, in order of
preference to which they wish to change over, as the change shall be strictly based
on their merit, subject to availability of vacancies.
(f) The change of branch shall be permitted purely on inter-se merit of all the eligible
applicants. The CGPA of students at the end of the second semester shall be
considered for rank ordering of the applicants seeking change of branch and in
the case of a tie, the MHCET ranks shall also be considered.
(g) All the changes of branch permitted for intending students as per the above clauses

7
 shall be effective from their third semester only and no further change of branch
shall be permitted after this.
(h) All the changes of branch permitted at this stage shall be final and binding on the
applicants and no student shall be permitted, under any circumstances, to refuse the
change of branch offered.
(i) The candidates who have sought admission under Tuition Fee Waiver Scheme are not
eligible for the branch change.

10. Course S t ru c tu re :
a) Each course offered in the B. Tech. curriculum at the College shall be listed by
using a total of five/six digits, the first two being letters and the remaining being
numerals, as follows:
i. The first two letters to represent the Department offering the Course in
abbreviated form, e.g., CE for Civil Engineering;
ii. The first numeral that follows to represent the year of the programme, such
as 1, 2, 3 and 4, leading to 100,- 400 series;
iii. The next two numerals to represent the Course Number allotted for the subject
by the Department, i.e., 01, 02, 03, up to 99;
iv. Thus, as an example, courses offered at the Department of Civil Engineering
could be listed from CE 101 up to CE 499;
b) All the courses in the B. Tech. Curriculum shall be unitized, with one credit being
assigned to each unit of course work, after the student completes its teaching-
learning process successfully.
c) The assignment of credits to course work shall follow the well accepted practice at
leading institutions, with one credit being defined to mean:
1. Lecture course conducted for one hour per week in a semester;
2. Tutorial conducted for one hour per week in a semester;
3. Laboratory/Practical conducted for two/three hours per week in a semester;
4. Project work conducted for two hours per week in a semester;
d) Each student for the B. Tech, Degree award shall be required to earn a total of
180 credits during his/her studentship at the College. While a student can
register for more than 180 credits at the College, only 180 credits shall be reckoned
for the Degree award. On the other hand, a student having less than 180 credits
shall have to earn the remaining credits to make up the total to 180 credits so as
to qualify for the Degree award. The total number of credits earned to complete the
course depends on the academic schema for which the student has enrolled for.
e) In addition to the credit requirement prescribed above for the Degree award, each
student shall have to complete the requirements of Extra Academic Activities (EAA)
as referred to earlier in Clause 2 of Section 7, during the first two semesters of the
programme. All the students shall receive certification as PP (for Passed), and NP
(for not passed) in EAA, in the Grade Card. While obtaining certification as PP is a
mandatory requirement for the Degree award of a student, t h i s shall not be taken

8
into account for computing the final Grade Point Average.
1. Each student shall register for an average of 22 credits per semester during
his/her studentship at the College, with the minimum and maximum credits
being fixed as 16 and 28 credits per semester respectively. The exact number
of credits to be registered by a student in a semester in a particular
Department shall be decided by his/her Faculty Advisor based on the student‟s
academic performance in the preceding semester and approval by the
Departmental Undergraduate Programme Committee (DUPC).
2. The medium of instruction for course work and examinations at the College
shall be English. The course work for the Programme shall be broadly divided
into S E V E N main subject groups, as follows:
 Humanities, Social Sciences and Management Courses;
 Engineering Foundation Courses
 Basic Sciences including Mathematics;
 Mandatory Learning & Liberal Learning Courses;
 Professional Core and Elective Subjects;
 Skill based Laboratory Courses
 Mini and Major Project
3. The total course package for the Programme at a Department shall have the
following components:
 Institutional Core subjects
 Departmental Core subjects
 Departmental Elective subjects
 Other Elective subjects
f) The DUPC shall be responsible for planning the curriculum and syllabi for all
the courses included for the Programme for approval by the Senate However,
the Institutional Undergraduate Programme Committee (IUPC) shall be in charge
for College wide implementation of course work, time tables and related
requirements for the Programme.
g) Each Department shall have the flexibility to include industrial training and/or field
work of 8 weeks for all its students as a compulsory requirement for the Degree
award and this can be assigned credits, as approved by the Senate. However,
these shall be arranged during the supplementary semester period following the
sixth semester of studies at the College.
h) Each Department s h a l l assign Faculty Advisors for all its students in
consultation with the Dean, Academic Affairs and Dean, Students Affairs. It shall
be the responsibility of the Faculty Advisors to help the students in planning
their course work and other academic activities at the Department and also to
regularly monitor and advise them on their academic and other performance at
the College. For students of the first two semesters in any Department, the Dean,
Students Affairs may assign Faculty Advisors from among the faculty of Basic
Science including Mathematics and HSS Departments.

9
11. Course Registration for the Semester :
(a) Each student shall be required to register for course work by following the advice
of the Faculty Advisor at the commencement of each semester on t he day fixed for
such registration and notified in the Academic Calendar.
(b) Students who fail to register for course work on the notified day may be permitted by
the Department for late registration on another day announced in the Academic
Calendar after payment of an additional fee fixed by the College.
(c) Only those students shall be permitted to register for course work who have:
i. Cleared all dues of the College, Hostel and Library including fines (if any)
of the previous semester,
ii. Made all the required advance payments towards the College and Hostel
dues for the current semester before the closing date, and
iii. Not been debarred from registration of courses on any other specific ground.
(d) Each student shall fulfill the following conditions at the time of registration of
course work in any semester:
i. Each student of the first year shall register for all the courses in the first two
semesters, with flexibility to drop one/two courses up to the minimum
permissible limit of 18 credits in each case. Similarly Direct Diploma students
will also register for all courses in third and fourth semester.
ii. A student shall be permitted to register for more than the average course
load, i.e., up to a maximum of 28 credits, if he/she has shown
outstanding performance in course work in the previous semesters, i.e.,
CGPA>=8.0.
iii. On the other hand, a student whose performance is not so good in the
preceding semesters, i. e., =<5.0, shall be permitted to register 18 credits,
the students who have secured CGPA in between 5 and 6 are allowed for normal
credits ( i.e. The credits offered by the department in that semester) and the
students who have secured more than 6 CGPA are allowed to
regist er for one add itional course. The students are mandatorily
required to register for backlog subjects first. The faculty advisor
is required to check for the pre -requisites if any at the time of
regist rat ion.
(e) All the students shall note the following special features of the credit system,
which shall be strictly followed at the College:
i. There shall be no re-examination facility as in the conventional academic
system and ESE shall be conducted for the course once in a semester, except
to meet the needs of students specially permitted by the College.
ii. A student shall have to re-register in all the failed courses (i.e., Getting Grade
FF) at any further semester when they are offered again, freedom being
given to the student to change the course only if it is an elective.
iii. Also, a student getting certification as NP in the Extra Academic Activities

10
 (EAC), shall re- register for them in a following semester/s until he/she
obtains certification as PP.
(f) A student shall have the possibility to drop a course in the middle of a semester as
per the Academic Calendar, without mention in the Grade Card, with the
concurrence of the Faculty Advisor, and after intimating the concerned course
instructor/s and the academic section. However, it shall not be possible for a
student to register for an alternative course in that semester.
12. Supplementary Semester:
(a) Departments shall have the flexibility to conduct supplementary semesters during
summer months for FY B.Tech backlog subjects, as per the Academic Calendar.
Such a semester shall be offered on the recommendation of DUPC and with the
approval of the Dean, Academic Affairs. A student shall be allowed to register for a
maximum of three subjects in a supplementary semester.
(b) The supplementary semester shall be utilized primarily to facilitate the failed
students to attend the FY courses in which they have failed and not for
launching any new courses for credit. However, a Department shall be free to
arrange any Add-On courses for its students during this semester.
(c) The academic activity in the supplementary semester shall be at double the rate as
compared to a normal semester; e.g., 1 credit of course work shall require two
hours/week in the class room, so that the contact hours are maintained the same as
in a normal semester. It shall also be necessary to fulfill the requirements of CIE
and ESE for all the courses like in a normal semester.
(d) Courses planned for the supplementary semester shall be announced by the Dean,
Academic Affairs in each year, well before the conclusion of the even semester.
Students intending to avail of this facility shall have to register for the courses
offered by paying the prescribed fees within the stipulated time.
(e) It shall be the responsibility of the Department to plan in advance the faculty and
non-teaching staff requirements to conduct the supplementary semester and
take necessary steps including the institutional approvals for organizing the same.
(f) The student who are either dropped or detained in the course/s during regular
semester is not allowed to register for that course/s in summer.
(g) Re-exam (ONLY for 60 marks equivalent to end semester exam) shall be conducted
for all other classes three weeks after grade approval by DUPC/DPPC. The re exam
shall be conducted after every semester, for the subjects offered in that semester.
For final grading, T1, T2 scores of respective semester shall be used. Grade ranges
shall be same as that of regular semester for that subject
13. Programme Duration:
(a) The Programme duration for a student to complete the academic and other
requirements at the College and qualify for the award of Degree by the University
shall be normally 8 semesters.
(b) However, it shall be possible for an outstanding student to qualify for the Degree
award in less than eight semesters, by registering for more number of credits i.e.,
up to the maximum permissible limit of 28 credits per semester from the third
semester onwards to complete the Programme requirements of 180 credits. In such
11
 a case, the College shall issue a Provisional Certificate to the student who shall await
the completion of eight semesters for the Degree award by the University.
(c) This flexibility shall also enable academically weaker students to conduct their studies
at a slower pace and complete their Degree requirements in more than eight
semesters. The maximum duration for the course completion will be 12 semesters.
(d) Clause (3) above shall be applicable to two types of students at the College:
i. Those wishing to complete the Degree requirements comfortably without
e n c o u n t e r i n g failure in any course;
(e) In both the above cases, a student shall have to complete the Programme
requirements for the Degree of 170 credits within 12 semesters. Failure to complete
the Programme requirements by any student in this period shall lead to the
cancellation of his/her admission to the College forthwith. The Senate on case to
case basis on the recommendations of the Director and Dean-Academics can
extend the term.
(f) A student will not be awarded degree if his/her CGPA at the end of the course is
less than 5. For such students the performance improvement scheme is
recommended wherein he/she is eligible to take any three subjects for the
improvement.

14. Temporary Withdrawal:

(a) Student shall be permitted to withdraw temporarily from the College on the
grounds like prolonged illness, grave calamity in the family or any other serious
happening. The withdrawal shall be for periods which are integral multiples of a
semester, provided that
i. He/She applies to the College within at least 6 weeks of the
commencement of the semester or from the date he/she last attended the
classes, whichever is later, stating fully the reasons for such withdrawal
together with supporting documents and endorsement of his/her guardian.
ii. The College is satisfied that, even by taking into account the expected period
of withdrawal, the student has the possibility to complete the Programme
requirements of 170 credits within the time limits specified earlier.
iii. The student shall have settled all the dues or demands at the College
including those of Hostel, Department, Library and other units.
(b) A student availing of temporary withdrawal from the College under the above provision
shall be required to pay such fees and/or charges as may be fixed by the College
until such time as the students name appears on the Roll List. However, it shall
be noted that t h e fees/charges once paid shall not be refunded.
(c) Normally, a student shall be entitled to avail of the temporary withdrawal facility
only once during his/her studentship of the Programme at the College.
15. Termination from the Programme :
A student shall be required to leave the College on the following grounds
i. Absence from classes for more than six weeks at a time in a semester

12
 without leave of absence being approved by the competent authorities, shall
result in the student‟s name being struck off the College rolls.
ii. Failure to meet the standards of discipline as prescribed by the College from
time to time shall also result in the student being recommended by the
Students Disciplinary Committee to leave the College.
16. Performance Assessment:
(a) There shall be achievement testing of all the students attending a course, like
lecture course, laboratory/design/drawing course or a combination of the two. This
shall be in two parts, as follows, both of them being important in assessing the
students performance and achievement in the particular course:
1. Sessional, involving Continuous Internal Evaluation (CIE), to be normally
conducted by the subject teacher all through the semester; This shall include
mid-term tests, weekly/fortnightly class tests, home work assignments,
problem solving, group discussions, quiz, seminar, mini-project and other
means. The subject teacher shall announce the detailed methodology for
conducting the various segments of CIE together with their weightages at the
beginning of the semester.
2. Terminal, often designated as End Semester- E x a m i n a t i o n ( ESE), to be
conducted by the subject teacher, preferably jointly with an external
examiner; This shall include a written examination for theory courses and
practical/design/drawing examination with built-in oral part for laboratory/
design/drawing courses.
3. CIE and ESE shall have 40:60 weightage. A student‟s performance in a subject
shall be judged by taking into account the results of CIE and ESE together.
4. The evaluation of the project work shall be based on Sessional Work
assigned by the project supervisor, seminar presentation, project report and
assessment by Project Evaluation Committee, as covered in Clause(7) later in
this Section.
5. In the case of other requirements, such as, seminar, comprehensive viva
voce and EAA the assessment shall be made as determined by the Grade
Awarding Authority of the College.
6. While the conduct of CIE for a course shall be the responsibility of the subject
teacher and the Department concerned, MSE and ESE shall be conducted
centrally by the Examination Section of the College. The records of both CIE
and ESE shall be maintained by the Examination Section.
7. The performance of students at every stage of the CIE shall be announced by
the concerned subject teacher within a fortnight of the date of the particular
assessment. The subject teacher shall also show the assessed answer books
to the students before submission of the final marks to the Controller of
Examinations.
8. The concerned subject teacher shall also be responsible to award letter
grades to the students after the ESE is completed and to submit the final
results of the course within one week of the last date of ESE to the
Controller of Examinations through the Head of his/her Department.

13
(b) Question Papers: For being able to conduct achievement testing of the students in an
effective manner, good question papers shall be used as the principal tool, making it
necessary for the question papers at CIE and ESE to:
i. Cover all sections of the course syllabus uniformly;
ii. Be unambiguous and free from any defects/errors;
iii. Emphasize knowledge testing, problem solving & quantitative methods;
iv. Contain adequate data/ other information on the problems assigned;
v. Have clear and complete instructions to the candidates.
(c) Therefore, the question papers, particularly at E S E , shall be set covering the entire
syllabus and the students given opportunity to answer questions from the full syllabus
of the course by restricting their choice out of each unit in the syllabus. For this to
be realized,
(d) Besides, the course syllabi shall be well drafted, be defect-free and properly unitized
(or modularized) to enable the distribution of questions in the question papers to
cover the whole syllabus. These aspects shall have to be taken into account, in
particular, by the concerned DUPCs.
(e) There shall be two types of questions to be set by the subject teacher for the
question papers at both CIE and ESE, viz.,
i. Multiple Choice Questions, having each question to be answered by tick
marking the correct answer from the choices (commonly four) given against it.
Such a question paper shall be useful in the testing of knowledge, skills,
comprehension, application, analysis, synthesis, evaluation and understanding
of the students. Usually, no more than 15- 20% of the questions in a paper
for CIE or ESE shall be of this type.
ii. Comprehensive Questions, having all questions of the regular type to be
answered in detail. Such a question paper shall be useful in the testing of
overall achievement and maturity of the students in a subject, through long
questions relating to theoretical/practical knowledge, derivations, problem
solving and quantitative evaluation.
(f) Examinations: The College shall maintain a high standard i n both CIE and ESE and
ensure the declaration of final results including SGPA and CGPA of the courses attended
by a student in a semester before the end of the semester as per the Academic
Calendar. For meeting these requirements, the College shall take the following steps:
i. CIE shall be conducted exclusively by the subject teacher, who shall spell
out the components of CIE in advance, maintain transparency in its
operation, declare the evaluation results in time and return the answer
scripts and assignment sheets to the students on a regular basis after the
evaluation is completed. The teacher shall also solve the questions asked in
the tests at the tutorial sessions for the benefit of weak students.
ii. ESE shall be preferably conducted jointly by the subject teacher and an
external examiner appointed for this purpose by the College. In this case,
considering the tight time schedule for the various tasks connected with
ESE, the external examiner shall be associated with the teacher only in the
setting of the question paper.

14
 iii. The answer scripts of ESE shall be evaluated by the subject teacher only; but,
an external review of the entire ESE shall be conducted under the aegis of
the Board of Examiners of the College before declaring the results. This step
shall be useful to the College to gain the confidence of the University on the
fairness and transparency in the system.
iv. Suggested passing standard for each of the courses shall be 50marks from the
CIE and ESE taken together.
v. Attendance at all examinations, both CIE and ESE of each course shall be
compulsory for the students. Students having the following deficiencies shall
not be permitted to attend the ESE:
A. Disciplinary action by the College pending against him/her;
B. Irregular in attendance at lecture/laboratory and other classes;
C. Failure to meet the standards of attendance prescribed ;
D. CIE Performance far below the passing standard

(g) In the event of a final year student failing in a Laboratory course or scoring very low
marks in the CIE of a subject or falling seriously ill during ESE, the subject teacher
concerned shall have the discretion to grant the student extra time, not exceeding
12 weeks for satisfactorily completing the concerned course after awarding an I grade.
If no such extra time is sought/granted, the concerned student shall have to re-
register for the same in a succeeding semester and take steps to fulfill the
requirements for the Degree award. The I grade shall be required to be converted
into a regular grade within stipulated period indicated in the academic calendar.
(h) Re-Examination: There shall be no re-examination for any course at the College to
take care of the failed students. Hence, the failed students shall re-register for the
course (the same course, if it is hard core, or an alternative course, if it is a soft
core or an elective) when it is offered again (either in a main or supplementary
semester) and fulfill the passing standards laid down to earn the specified credits.
However, there shall be make- up examination for a course to take care of students
with the I or X grades in ESE.
(i) Make Up Examination: This facility shall be available to students who may have
missed to attend the ESE of one or more courses in a semester for valid reasons
and given the I grade; also, students having the X grade shall also be eligible to take
advantage of this facility. The make up examination shall be held as per dates
notified in the Academic Calendar. However, it shall be possible to hold a make up
examination at any other time in the semester with the permission of the Dean,
Academic Affairs. The standard of conducting this examination shall be the same as
the normal ESE.
(j) Evaluation of Project work The project work shall be normally conducted in two
stages, spread over one or two sequential semesters.
i. At the end of first stage, the student shall be required to submit for
evaluation, a preliminary report of the work done before a prescribed date to
the Project Coordinator, DUPC and present the same before an Internal
Project Evaluation Committee. This shall be followed by taking up the second
stage of work either in the same or the following semester.

15
 ii. The Controller of Examinations shall receive a panel of names from the
Chairman, DUPC for identifying the project examiners for the student, at least
two weeks before the submission of the second stage of project work. This
shall comprise of three unbound, typed copies of the project report (one for
each examiner), prepared according to the prescribed format to be submitted
to the Department at least one week before the date of oral examination.
iii. The Department s h al l record the date of submission of the project report
and arrange to send copies of the same to the examiners a few days before
the date fixed for the oral examination. The project coordinator shall notify
the date of the oral examination to the examiners and also the student,
w i t h a copy marked to the Controller of Examinations. Then the project
report shall be evaluated by the Project Evaluation Committee and the result
submitted to the Project Coordinator, who in turn shall forward it to the
Controller of Examinations.
iv. On successful completion of the oral examination, the student shall be
required to submit two bound copies of the final, corrected project report,
one being for the Department and the other for the project supervisor(s).
v. A student desirous of extension of time, up to a maximum of 3 months
from the prescribed date for submission of the project report, shall seek
permission for the same from the Project supervisor(s) and Head of the
Department. The DUPC shall consider such requests, case by case, before
giving the permission.
vi. If the DUPC is convinced that the progress of a student in project work
is insufficient, the concerned students shall be temporarily awarded the I
grade. Further, if the project report of the student is not submitted within
the extended time period, the I grade shall be automatically converted to the
FF grade.
vii. Such of the students who fail in the first stage assessment of project work
shall be required to re-register for the first stage in the following semester.
Likewise, those who obtain the FF grade in the second stage assessment
shall be required to re-register for the same in the subsequent semester(s).
(k) The evaluation of performance in EAAc shall be done by the concerned faculty
members, who shall communicate the student‟s performance to the Examination
Section, soon thereafter.
17. Grading S y s t e m :
(a) The College shall follow the award of letter grades and the corresponding grade
points to the students based on their performance at the end of every semester, as
given in Table 2, In addition to the grades given in the Table 2, the instructors
shall use two transitional grades I and X as described in Clause (3) in this Section.

Table 2 : Letter Grades a n d Grade Points

Grade Grade Points
AA 10
AB 9

16
 BB 8
BC 7
CC 6
CD 5
DD 4
FF 0
PP 0
(Only for Compulsory
Non Credit Subjects)

AU (Audit Subject) 0

NP (Only for Non Not Passed

Credit Subjects)

(b) A student is considered to have completed a course successfully and earned the
credits if he/she secures a letter grade other than I, ‟X‟ or FF in that course. Letter
grade FF in any course implies failure in that course.

(c) The Transitional Grades I and ‟X‟ shall be awarded by the teachers in the
following cases:
i. Grade I to a student only on satisfactory attendance at classes and
performance in other components of assessment, but absence from ESE in a
semester for valid and convincing reasons acceptable to the Department,
such as,
A. Illness or accident, which disabled him/her from appearing at the
examination;
B. A calamity in the family at the time of the examination, which
required the student to be away from the College;
ii. Grades X to a student on his/her overall performance in the course during
the semester, highly satisfactory, i.e., high CIE rating, but a very low ESE
performance resulting in an overall F Grade in the course.
iii. All the I and X grades awarded to the students shall be converted by the
teachers to appropriate letter grades and communicated to the Academic
Section (through Head of the Department) within two days of the respective
make-up ESEs. Any outstanding I and X grades two days after the last
scheduled make-up ESEs shall be automatically converted to FF grade.
(d) A Semester Grade Point Average (SGPA) shall be computed for all the students in a
Department for each semester, as follows:

SGPA = (C 1 *G 1 + C 2 *G 2 + C 3 *G 3 +. . . + C n *G n) / (C 1 + C
2 + C 3 +. . . + C n)
where, n is the number of courses registered during the semester, Ci is the
number of credits allotted to a particular course, and Gi is the grade points

17
 corresponding to the grade awarded for the course.
(e) A Cumulative Grade Point Average (CGPA) shall be computed for all the students
in a Department at the end of each semester by taking into consideration their
performance in the present and the past semesters as follows:
CGPA = (C 1 *G 1 + C 2 *G 2 + C 3 *G 3 +. . . + C m *G m) / (C 1 +
C 2 + C 3 +. . . + C m)
where, m is the number of courses registered upto that semester, Ci is the
number of credits allotted to a particular course, and Gi is the grade points
corresponding to the grade awarded for the course.
(f )Whenever, a student repeats or substitutes a course in any semester, the lower
of the two grades obtained by him/her in the course shall be ignored in the
computation of CGPA from that semester onwards and the students shall be given
the benefit of a higher grade.
(g) Both the SGPA and CGPA shall be rounded off to the second place of decimal and
recorded as such for ease of presentation. Whenever the CGPAs are to be used for
the purpose of determining the merit ranking in a group of students, only the
rounded off values shall be made use of.
(h) When a student gets the grade I or X for any course during a semester, the SGPA
for that semester and the CGPA at the end of that semester shall be tentatively
calculated ignoring the I and X graded course(s). The SGPA and CGPA for that
semester shall be finally recalculated after conversion of I and X grade(s) to
appropriate grade(s), taking into account the converted grade(s).
(i)Other academic requirements for the Programme include the following two
certifications as indicated earlier in clause (5 ) of Section 10, viz., PP (Passed)
and NP (Not Passed) for EAA. However, there shall be no grade points are
associated with these certifications and they do not figure in the calculation of
SGPA or CGPA. But, obtaining a PP shall be a mandatory requirement to qualify for,
the Degree award.
(j) It shall be open to each student to take additional courses for audit from the fifth
semester onwards, with the concurrence of the Faculty Advisor. Students
h a v i n g CGPA ¿= 8 . 0 shall be normally encouraged to take such courses. While
the performance of the student i n audited courses shall be included in the
Grade Card, they do not contribute to SGPA or CGPA of the concerned student.
18. Method of Awarding L e t t e r Grades:
(a) The subject teacher(s) shall award the letter grade(s) to students based on the
marks secured by them in both CIE and ESE together in the course(s) registered.
This shall be done by following a relative grading system based on the use of
statistics, for which the IUPC shall make available an appropriate software package.
(b) The subject teacher(s) s h a l l submit two copies of the result sheet for each
course, giving both the marks and the grades awarded to the Head of the
Department, before the due date specified in the Academic Calendar. This shall be
forwarded to the Controller of Examinations soon thereafter by the Head of the
Department, after preliminary scrutiny and moderation (if necessary) at the DUPC

18
 level.
(c) All the evaluated answer scripts of CIE in a subject shall be returned to the students
from time to time during the semester. However, the answer scripts of ESE shall
only be shown to the students during the specified period after the evaluation and
the detailed marks sheets together with ESE answer scripts and any other relevant
papers connected with ESE shall be submitted by the subject teacher(s) to the
Controller of Examinations who shall hold it for a period of at least one semester.
Steps shall be taken to destroy the same only after obtaining permission from the
Dean of Academic Affairs at the end of the prescribed period.
(d) Appeal: A student shall have the possibility to appeal to the Director against a
subject teacher for awarding lower grade in a course than that e x p e c t e d by
him/her, o n payment of prescribed fees, before the commencement of the next
semester. In such a case, the DUPC shall arrange a meeting of the aggrieved
student together with a Committee comprising of the subject teacher, another
subject expert from the College and the Head of the Department, who shall
reconsider the evaluation done, show the answer script to the student. If the
student is satisfied, the matter shall be closed at this stage. On the other hand, if
a revision of marks allotted is called for, the same shall be carried out and all the
records, including the Grade Card, corrected soon thereafter. In the latter case,
the prescribed fee paid by the student shall be returned.
(e) Withholding of Grades: The Grades of a student in a semester shall be withheld
and not declared if the student fails to pay the dues to the College or has
disciplinary action pending against him/her.

19. Eligibility for the Award of Degree:

(a) A student shall be eligible for the award of B. Tech. Degree from the College
and the University provided, he/she has:
(b) The Senate shall be the Recommending Authority for the award of B. Tech.
Degree to students fulfilling the requirements specified under Clause (1) above and
the Board shall be the Approving Authority.
(c) The Degree award shall then be granted by the University.
i. Completed all the prescribed credit requirements for the award of Degree with
grade DD or higher, in each of the courses, like Theory, Laboratory, Studio,
Workshop, Seminar and Project Work;
ii. Satisfactorily completed all the non-credit requirements with PP certification,
covering EAA and Industrial Training, Field work, (if any);
iii. Obtained a CGPA of >= 5.00 at the end of the semester in which he/she
c o m p l e t e s all the requirements for the award of Degree;
iv. Paid all the dues to the College including the Department, Hostels, Library and
o t h e r units; and,
v. No case or disciplinary action pending against him/her.

19
20. Eligibility for the CGPA improve me nt afte r c omple tion of pre -
re quisite c redits for the award of D e gree :

Students who secure CGPA between 5 and 6.75 after completing the pre-requisite
credits for the award of degree, and wish to improve their CGPA are permitted for
CGPA improvement. Such students be permitted to withdraw their grade in a given
course with poor grade and permitted to reappear for the examinations for improving
the grade and in turn CGPA.
a) Student can appear for grade improvement examination within one year from the
date of passing his/her PG or UG Examination. He should not have taken (i)
Leaving Certificate from the Institute and ii) Degree from University of Pune
through convocation. He/she will submit a written application to dean academics
seeking his/her permission to register for class improvement within one month
from the date of declaration of result or one week before the date of convocation
of University of Pune whichever is earlier. This application will be forwarded to
dean academics through the Head of the Department from where he/she has
graduated. No student will be admitted once the subject registration process of
that semester ends.
b) For grade improvement student will have to take maximum 3 subjects in which
he/she has secured DD or CD grades from the same semester in one stretch.
c) Student can choose maximum three theory courses from a particular semester
offered for T.Y and B. Tech (either odd or even) in which he/she has secured DD
or CD grade. Student will have to register for these courses in a particular
semester in which those subjects are offered.
d) At the time of registration student will surrender all the original mark lists given to
him by the institute He will have to give an affidavit on 100 Rs. judicial stamp
paper that he/she will not do any use of surrendered mark lists till he/she gets
official result of the subjects for which he/she wishes to appear for grade
improvement. No change of subjects or drop of subjects will be allowed after
registration.
e) Student wishing to improve his/her grade will have to pay appropriate fees as laid
down by the institute time to time.
f) Student wishing to appear for grade improvement is exempted from attending
regular classes as he/she has already undergone the course instructions but
he/she will have to appear for all the evaluation tests conducted for the particular
subjects. No re-exam or retest will be allowed for the class improvement, in case
of such students misses any of the tests or examinations. Absentee for End-
semester examination will automatically lead to award of FF grade in that subject.
g) The grading process as used for the regular students appearing for that subject
will be applicable and no concession of any sort will be granted on account of
absentee for any of the examinations.
h) Student wishing to use the facility of grade improvement will have to pass in all
the three subjects at a time for which he/she has registered for. He/she will not
be entitled for the summer term or re-examination in such cases.
i) Only one attempt will be permissible for any candidate wishing to use the facility
of grade improvement. If the student fails to secure higher grades resulting in
reduction in overall CGPA then the original resul t of the student before registering

20
 for grade improvement will be retained.
j) Student who improves his/her CGPA will be issued fresh mark lists by the institute.
These mark lists will have star against the subjects for which he/she has appeared
for grade improvement and will state “Grade Improvement”. The date on the new
mark lists will be that as issued for other students appearing in those subjects.
Name of the student will be communicated to Pune University and he/she will
have to apply for degree certificate from University of Pune thereafter.
21. Honors and Minor Certification Schemes at the Institute (To be implemented
w.e.f A.Y. 2017-18 for Third Year Students:

• Aspiring student has to register for additional FOUR THEORY courses and acquire a
additional (minimum) 12 credits (3 credits/course) for any ONE of BOTH the Schemes.
• Honors Certificate for Vertical in his/her OWN Branch for Research orientation; Minor in
any OTHER Branch for Improving Employability.

• For MINOR scheme:

– Every Department to develop and submit „Minor-Courses-List‟ of 5-6 Theory
courses with Titles and detailed syllabi, separately.
• e.g. E & TC dept.: Linear & Digital ICs, DSP, Embedded Processors,
Digital Communication, Communication Networks.
– Student from ANY department is ELIGIBLE to apply for Minor from ANY OTHER
DEPARTMENT.
– The Scheme would start from 5th Semester of UG program and applicant must
have a minimum CGPA of 6.0 (up to 4th Sem).
– Host Department to float a SINGLE course from Minor-List, ONE in EVERY
Semester starting from 5th Semester (Four courses in Four Semesters viz. 5, 6, 7,
8).
– NO Lab course/Internship/Mini-project/MOOC permitted in Minor Scheme.
– All Minor Courses to be designed and delivered by Departments only.

• For HONORS Scheme:

– Every Department to develop and submit a „Honors-Courses-List‟ of 5-6 Theory
courses with Titles and detailed syllabi. MOOCs are permitted to be part of the
list, so also a few PG courses. Multiple Verticals are encouraged. (e.g. Digital
Communication/Signal Processing/Communication Networks/VLSI
Design/Embedded Systems/ etc.)
– Student from Host Department to undertake the Honors scheme for his/her own
branch.
– Scheme would begin from 5th Semester of UG program.
– Applicant should have CGPA score of 6.0 (up to 4th Semester)
– Host Department to float the courses from Honors-List as ONE in each Semester
(viz. 5th, 6th, 7th, 8th Sem, of which preferably the SECOND course could be a

21
 MOOC from NPTEL/edX/Coursera/Udacity//PurdueNext/Khan Academy/QEEE etc.
with examination given by the Department.

• Implementation:
– 01 Minor & 01 Honors each = 02 Courses in every Semester beginning from 5th
Sem. upto 8th Sem. Total: 08 Courses.
– A Student opting for „Honors‟ will NOT be ENTITLED to register for „Minor‟.
– Allotment of SLOT in Time table on the line of ILOE (e.g. Mon-Wed: 9 to 10 am).
– Department to identify and appoint a faculty member as „Honors/Minor
Coordinator‟ for guiding the aspirants.

• Specific Remarks:
– Normal UG program for B.Tech. degree is therefore of reduced credits in
comparison to previous iterations of Curriculum revision, (170 credits
across Eight semesters).
– Mediocre learner would find it bit easier to complete the program with good
scores, with such reduced credits.
– So, for Brighter Students opting Honors/Minor scheme, the UG program would
be of 170 + 12 = 182 credits.
– Average learners can receive B.Tech degree with normal 170 credits.
– The remedial assessment schemes such as Re-examination or Summer term will
NOT be applicable for Minor or Honors schemes. Student failing in any of the
Minor or Honors courses, at any stage will be discontinued from the Scheme.
– The schemes shall also be open for Second Year Direct Admitted Diploma
Students, with CGPA of Second Year at COEP exceeding 6.0.

******

22
 Program Education Objectives (PEOs):
The Undergraduate students will demonstrate...
I. To prepare the students in order to cater the needs of automotive, design, thermal and
manufacturing for Indian as well as multinational industries.
II. To develop competence in the students to understand technological concepts, analyze data in
order to formulate and undertake industrial problems and obtain viable solutions.
III. To provide students with in depth knowledge in the core subjects such as mathematics and
engineering sciences in order to prepare them for higher studies and inculcate research
attitude.
IV. To make students aware of the importance of lifelong learning and provide opportunity to work
on multidisciplinary projects.
V. To inculcate in student effective communication, management skills, professional ethics, codes
of professional practice, induce societal awareness and indoctrinate team spirit.

Program Outcomes (POs):

The Undergraduate Students will demonstrate...

1. Proficiently use mathematical methods, basic sciences, engineering analysis, measurement and
instrumentation techniques while attempting engineering problems and articulate viable
solutions.
2. Graduates will demonstrate the ability to design, develop and analyze mechanical systems and
manufacturing process that meets the required specifications.
3. Graduates will be familiar with modern engineering software tools and equipment to analyze
mechanical engineering problems.
4. Graduates will demonstrate an aptitude to identify, formulate and solve problems associated
with Mechanical Engineering.
5. Graduates will be able to understand the intricacies and impact of engineering solutions.
6. Graduates will be able to communicate effectively in both verbal and written forms.
7. Graduates will identify societal problems and provide viable engineering solution.
8. Graduates would be capable of self-education and clearly understand the value of lifelong
learning.
9. Graduates will be broadly educated and will have an understanding of the impact of engineering
on society and demonstrate awareness of contemporary issues.
10. Graduates will demonstrate professional and ethical responsibilities.
11. Graduates will adhere to the various important issues such as green house effect, carbon credit
retrofit design concept; relevant norms laid down and exhibit maturity while providing
engineering solutions.

23
 Correlation between the PEOs and the POs

PO→ 1 2 3 4 5 6 7 8 9 10 11
PEO↓
I      
II        
III       
IV      
V      

Note: The cells filled in with  indicate the fulfilment/correlation of the concerned PEO
with the PO.

24
 List of Abbreviations

Abbreviation Title
S.P. P.U. Savitribai Phule Pune University
A.Y. Academic Year

BSC Basic Science Course

EFC Engineering Foundation Course

MLC Mandatory Learning Course

ILOE Institute Level Open Elective Course

SLC Self Learning Course

HSMC Humanities/Social Sciences/Management Course

LLC Liberal Learning Course

SBC Skill Based Course

PCC Program Core Course
DEC Department Elective Course

LC Laboratory Course

25
 Semester III
Teaching Scheme
Sr. Course Credits
Course Name
No. Type L T P
Ordinary Differential Equations and Multivariate
1 BSC 2 1 - 3
Calculus
2 BSC Science of Living System 3 - - 3
3 PCC1 Engineering Thermodynamics 2 1 - 3
4 PCC2 Machine Drawing and Computer Graphics 2 - - 2
5 PCC3 Manufacturing Engineering-I 3 - - 3
6 PCC4 Strength of Materials 3 - - 3
7 SBC Machine Drawing and Computer Graphics Lab - - 4 2
8 SBC Manufacturing Engineering - I Lab - - 2 1
9 LC1 Strength of Materials Lab - - 2 1
15 2 8 21
Total Academic Engagement and Credits 25 21

Semester IV
Course Teaching Scheme
Sr. Credits
Type Course Name
No. L T P
1 BSC Vector Calculus and Partial Differential Equations 2 1 - 3
2 MLC Professional Ethics & Values 1 - - 0
3 HSMC Innovation 1 - - 1
ILOE 1. Automobile Engineering OR
2. Smart Materials OR
4 3 - - 3
3. Computer Aided 3 D Geometric Modelling
[For Other Departments]
5 PCC1 Theory of Machines – I 3 - - 3
6 PCC2 Fluid Mechanics 2 1 - 3
7 PCC3 Fundamentals of Metallurgy 3 - - 3
8 PCC4 Manufacturing Engineering-II 3 - - 3
9 LC1 Theory of Machines – I Lab - - 2 1
10 LC2 Fluid Mechanics Lab - - 2 1
11 LC3 Fundamentals of Metallurgy Lab - - 2 1
12 SBC Manufacturing Engineering- II Lab - - 2 1
18 2 8 23
Total Academic Engagement and Credits 28 23

26
 Semester III (For Direct Second Year Admitted Diploma Students)

Sr. Course Teaching Scheme

Course Name Credits
No. Type L T P
1 BSC Linear Algebra and Univariate Calculus 4 1 - 5
2 BSC Foundation of Physics 3 - - 3
3 BSC Science of Living System 3 - - 3
4 PCC1 Engineering Thermodynamics 2 1 - 3
5 PCC2 Machine Drawing and Computer Graphics 2 - - 2
6 PCC3 Manufacturing Engineering-I 3 - - 3
7 PCC4 Strength of Materials 3 - - 3
8 SBC Machine Drawing and Computer Graphics Lab - - 4 2
9 SBC Manufacturing Engineering - I Lab - - 2 1
10 LC1 Strength of Materials Lab - - 2 1
17 02 8 23
Total Academic Engagement and Credits 30 26

Semester IV (For Direct Second Year Admitted Diploma Students)

Sr. Course Teaching Scheme

Course Name Credits
No. Type L T P
1 BSC Multivariate Calculus and Differential Equations 4 1 - 5
2 MLC Professional Ethics & Values 1 - - 0
3 HSMC Innovation 1 - - 1
ILOE 1. Automobile Engineering OR
2. Smart Materials OR
4 3 - - 3
3. Computer Aided 3 D Geometric Modelling
[For Other Departments]
5 PCC1 Theory of Machines – I 3 - - 3
6 PCC2 Fluid Mechanics 2 1 - 3
7 PCC3 Fundamentals of Metallurgy 3 - - 3
8 PCC4 Manufacturing Engineering-II 3 - - 3
9 LC1 Theory of Machines – I Lab - - 2 1
10 LC2 Fluid Mechanics Lab - - 2 1
11 LC3 Fundamentals of Metallurgy Lab - - 2 1
12 SBC Manufacturing Engineering- II Lab - - 2 1
20 2 8 25
Total Academic Engagement and Credits 30 25

27
 Semester-III

(MA16001) Ordinary Differential Equations and Multivariate Calculus

Teaching Scheme: Examination Scheme:

Lectures : 2 Hrs/week T1 and T2: 20 Marks each
Tutorial: 1Hr/week End-Sem Exam: 60 Marks

Course Outcomes:
Students will be able to:
1. Know and recall core knowledge of the syllabus. (To measure this outcome, questions may be of
the type- define, identify, state, match, list, name etc.)
2. Understand basic concepts. (To measure this outcome, questions may be of the type- explain,
describe, illustrate, evaluate, give examples, compute etc.)
3. Analyze the problem and apply the appropriate concept. (To measure this outcome, questions
will be based on applications of core concepts)
4. Give reasoning. (To measure this outcome, questions may be of the type- true/false with
justification, theoretical fill in the blanks, theoretical problems, prove implications or corollaries
of theorems, etc.)
5. Apply core concepts to new situations. (To measure this outcome, some questions will be based
on self-study topics and also comprehension of unseen passages.)
6. Organize and present thoughts. (To measure this outcome, questions may asked to write
summaries and short notes on a given topic.)
7. Analyze the problem and apply the appropriate concept. ( To measure this outcome, questions
will be based on applications of core concepts)

Unit I :
Review of first order differential equations, Reduction of order, linear differential equations,
homogeneous higher order linear differential equations, non-homogeneous higher order linear
differential equations with constant coefficients and reducible to differential equations with constant
coefficients (method of undetermined coefficients and method of variation of parameters), systems of
differential equations, applications to orthogonal trajectories, mass spring systems and electrical
circuits. [10 Hrs]

Unit II :
Functions of several variables, level curves and level surfaces, partial and directional derivatives,
differentiability, chain rule, local extreme values and saddle points, constrained optimization.
[05 Hrs]

Unit III :
Double integrals in Cartesian and polar co-ordinates, iterated integrals, change of variables, triple
integrals in Cartesian, spherical and cylindrical co-ordinates, substitutions in multiple integrals,
Applications to Area, Volume, Moments and Center of Mass. [11 Hrs]

28
Text Books:
 Maurice D. Weir, Joel Hass, Frank R. Giordano, "Thomas’ Calculus", Pearson Education, 12th
Edition.
 Erwin Kreyszig, "Advanced Engineering Mathematics", Wiley eastern Ltd., 10th Edition

Reference Books: Author name, "Title of the book in double quotes", Publisher, Edition, Year K.D Joshi,
“Calculus for Scientists and Engineers”, CRC Press.
 Sudhir Ghorpade and Balmohan Limaye, “A Course in Multivariate Calculus and Analysis”,
Springer Science and Business Media.
 George Simmons, “Differential Equations with Applications and Historical notes”, Tata Mc-Graw
Hill publishing company Ltd, New Delhi.
 C.R. Wylie, “ Advanced Engineering Mathematics” , McGraw Hill Publications, New Delhi
 Peter V. O’ Neil, “Advanced Engineering Mathematics”, Thomson Brooks / Cole, Singapore, 7th
edition

(AS 16001) Science of Living System

Teaching Scheme Examination Scheme

Lectures : 3 lectures/week T1-20 (Classroom activity),
T2-20 (Assignment/s)
Semester End Examination-60

Objectives: To make students conversant with basic Biology regarding the life processes. To impart
knowledge about the common corridors of biology and engineering as biologically inspired technologies
like designs in nature, bioenergetics, bioprocesses, biomaterials, biomechanics, bioimaging,
bioinformatics, bioinstrumentation etc. To introduce recent trends in biology viz. genetic & tissue
engineering, stem cell engineering, bio and nanotechnology etc. with the objective of appreciating
engineering principles in biological systems.

Unit 1: Understanding Basics (6L)

1. Engineering perspectives of biological sciences: Where engineering meets biology and where
biology meets engineering. Biology as an integrated Science; Case studies on integrating biology
with engineering.
2. Biopolymers and macromolecules – Structure and Function: Organic and inorganic molecules;
Unique Properties of Carbon; Carbohydrates, Amino Acids and proteins, Lipids, Nucleic Acids,
Vitamins and Minerals; The Rise of Living Systems.
3. Levels of organization of life : Cell as basic unit of life, prokaryotic and eukaryotic cells, microbes,
plant and animal cells; Cell organelles – structure and function; Levels of organization of life -
tissues, organs, systems and organism.

Unit 2: Biological Processes and Bioenergetics (6L)

1. Energy Dynamics in Biology –
a) Photosynthesis and energy assimilation: aerobic and anaerobic systems. Applications
b) Respiration and Electron Transport Chain: Mitochondria and respiration, ATP
generation.

29
 2. Bioenergetics: Thermodynamic principles applied to biology, negative entropy changes in
biological systems, Free Energy, Chemical Equilibrium;
3. Optimization of biological functions: Metabolic networks; anabolism and catabolism; flux
analysis (MATLAB).

Unit 3: Living Systems (6L)

1. Transport Phenomena in Biological Systems: Membrane channels and ion channels; Fluid flow
and mass transfer
a. In plants: Xylem and Phloem
b. In animals: Blood and Lymph
c. Transport of molecules and gases (Oxygen and Carbon dioxide); Heat Transport - Body
temperature regulation.

2. Communication: Cell junctions, Cell-cell communications – cell signaling, Hormones,

Pheromones; Chemotaxis. Communication in living systems by photo, bio, chemotactic
methods.
3. Defense mechanisms in plants and animals:
a. In plants: Herbivory, secondary metabolites.
b. In animals: Innate and Adaptive immune systems.

Unit 4: Techniques and Devices (6L)

1. Genetic Code - Expression and Transmission of Genetic Information, The concept of DNA
cloning; Mechanisms of Enzyme Action.
2. Techniques for optimization:
a. At molecular level: Genetic Code and protein synthesis, DNA replication, RDT, DNA
hybridization, Colony Hybrids, PCR, DNA microarray,
b. At cell level: Hybridoma technology,
c. At tissue level: Plant Tissue Culture, Animal Tissue Culture and Microbial Culture techniques;
Tissue Engineering.
3. Instrumental Methods of analysis – A case study of protein purification and characterization:
Principles and types of microscopy and spectroscopy, Chromatography, electrophoresis,
diffusion, centrifugation, light scattering.

Unit 5: Discovery and Innovation (6L)

1. Current trends and advances in cell and molecular biology
2. Landmark Discoveries: Landmark discoveries in the field of Molecular Biology, Cell Biology and
Genetics.
3. Nanobiotechnology: Micro-/Nanotechnologies for Interfacing Live Cells; Nanotechnology in
Medicine – Diagnostics and Therapy; Biosensors; Nanotechnology in Agriculture; Biomemetics.
4. Biomemetics: Nature inspired processes applicable to the field of Engineering.

Unit 6: Branch-wise
Branch: Electronics and Telecommunication Engineering
Biosensors – Introduction to Biosensors, transducers, amplifiers; Bioimaging-Introduction to medical
imaging and different medical Imaging modalities; Review of Signals and system; Electro Physiological
Signal Analysis. Bio-telemetry Communication in living systems by photo, bio, chemo, tactic methods;
Diagnostic Devices- Radiography, X-ray Computed Tomography Nuclear Medical Imaging, Ultrasound
Imaging, Magnetic Resonance Imaging. Therapeutic Devices-Cardiac Pacemakers, Cardiac defibrillators,

30
Surgical Diathermy, Diagnostic application of LASERs, High frequency heat therapy, Hemodialysis,
Ventilators, Anesthesia machines, Automatic Drug delivery Systems, Electro Surgical units and safety.

Branch: Instrumentation and Control Engineering

Basic concepts of Medical Instrumentation: Generalized medical Instrumentation System, Medical
Measurement constraints, Classification of Biomedical Instruments, Generalized static and dynamic
characteristics, Design criteria, Commercial Medical Instrumentation Development process, Regulation
of Medical Devices. Biomedical transducers: optical, photo- electric, electrochemical, electrical,
mechanical, electromechanical and thermoelectric. Specialty areas in Bioinstrumentation—Confocal,
Tunneling, Sequencing, FACS, PCR, MRI, CT,USG, Endoscopy, ECG; Introduction to biosensors and tissue
engineering.

Branch: Mechanical Engineering

Biomechanics, Human body motion, Prosthetics; Introduction to Ergonomics; Elements of
Anthropometry; Physiology, Anatomy; Mechanical Properties of Bone and Soft Tissues Rehabilitation
engineering, Biomimetics; Bio Material Handling; Hand Tool Design; Human Information Processing;
Applications of Principles of Biomechanics in two and three dimensional kinematics; Fundamentals of
Fluid Mechanics; Introduction to bio sensors and tissue engineering.

Branch: Metallurgy and Material Science

Classification of biomaterials –Comparison of properties of some common biomaterials; Effects of
physiological fluid on the properties of biomaterials; Biological responses (extra and intra vascular
system) to Metallic, Ceramic and Polymeric implant materials; Introduction to bio sensors and tissue
engineering. Metals & alloys, composites and their advantages used in bio-industries; Materials in bio-
printing. Tissue Engineering and cloning: Engineering cells, tissues and organs; Stem cells and
translational medicine; Introduction to Gene Therapy; Bioengineering at molecular, cell and systems
level; 3D bio-printing; Engineering Materials for Biomedical Applications.

Branch: Production Engineering and Industrial Management

Bio chemical engineering; Fermentation Technology, Bioreactors; Bio process Engineering; Use of living
organisms (mostly microbes) to produce useful products. Biomechanics and ergonomics–production
innovations.

Branch: Electrical Engineering

Alternative energy sources; Electrical signaling in biological system; Bioluminescence, bioelectricity, ECG.

Branch: Civil Engineering

Environmental engineering, Understanding ancient engineering. Designs in Nature; Bio radars.

Branch: Computer and Information Technology –

Principles of Bioinformatics, Computational Biology: Role of Computational Biology in Bioengineering;
Genomics, Proteomics, Bioinformatics. Computational solutions to Biological Problems, Virtual systems
Artificial Intelligence in Biomedical Engineering: Basics of Artificial Neural Networks.

Selected References:

1. Lodish H, Berk A, Zipursky SL, et al. (2000) Molecular Cell Biology. W. H. Freeman.

31
 2. Lehninger, A. L., Nelson, D. L., & Cox, M. M. (2000). Lehninger principles of biochemistry. New
York: Worth Publishers.
3. Lewin B. (2000) Genes VII. Oxford University Press..
4. Rao CNR, et.al. Chemistry of Nanomaterials: Synthesis, Properties and Applications.
5. Eggins BR. (1006) Biosensors: An Introduction. John Wiley & Sons Publishers.
6. Palsson B.O. and Bhatia S.N. (2009) Tissue Engineering. Pearson.

(ME 16001) Engineering Thermodynamics

Teaching Scheme: Examination Scheme:

Lectures : 2 Hrs/week T1 and T2: 20 Marks each
Tutorial: 1Hr/week End-Sem Exam: 60 Marks

Course Outcomes:

Students will be able to

1. Apply basic laws of thermodynamics in analysis and design of thermodynamic cycles including
vapor and gas power cycles, refrigeration cycles, and heat-pump.
2. Use thermodynamic relations in evaluation of thermodynamic properties.
3. Apply the fundamentals of conservation of mass and energy, and properties of ideal gas
mixtures in design and analysis
4. Enhance problem solving skills.
5. Evaluate performance of air standard cycles
6. Gain design skills in thermal systems and enhance written communication.

Unit I : Basic concepts and properties:

Introduction, thermodynamic system, control volume, macroscopic and microscopic approaches,
properties and state of a system, point and path functions, thermodynamic equilibrium, processes and
cycles, quasi-static process, properties such as specific volume, pressure, temperature, zeroth law of
thermodynamics, temperature scales. [5hrs]

Unit II : Ideal gases and vapors:

Difference between gases and vapors, ideal gases, gas laws, equation of state, gas constant, universal
gas constant, work and heat, definition of work, thermodynamic work, work in compressible system,
work-a path function, work done during various processes, p-v diagram, definition of heat, heat
transfer a path function, comparison of heat and work, Phase change process of a pure substance:
specific heats, sensible heat and latent heat, triple point, critical point, superheat and total heat of
steam. [6hrs]

Unit III : First law of thermodynamics:

Energy of systems, classification of energy, law of conservation of energy, first law applied to closed
system undergoing a cycle, Joule experiment, energy-a property of system, internal energy: a function of
temperature, enthalpy, specific heat at constant volume and constant pressure, change in internal

32
energy and heat transfer during various non-flow processes. First law applied to flow processes: steady-
state steady flow process, mass balance and energy balance in steady flow process, steady flow energy
equation and its application to nozzles and diffusers, throttling valve, turbines and compressors, pumps,
heat exchangers etc. Work done and heat transfer during steady flow processes. [6hrs]

Unit IV : Second law of thermodynamics:

Limitations of first law, heat engines, refrigerators and heat pumps, Kelvin-plank and Clausius
statements, their equivalence, reversible and irreversible processes, factors that render processes
irreversible, Carnot cycle, two propositions regarding the efficiency of Carnot cycles, the
thermodynamic temperature scale, reversed Carnot cycle, COP of heat pump and refrigeration.
Thermodynamic processes – constant volume, isothermal, adiabatic, polytropic processes, throttling
and free expansion- p-v and T-s diagrams-work done, heat exchanged, change in internal energy.
[7hrs]

Unit V : Entropy:
Inequality of Clausius, entropy: a property of system, entropy change for ideal gases, entropy change of
a system during irreversible process, lost work, principle of increase of entropy. Availability and
irreversibility: available energy referred to cycle, decrease in available energy with heat transfer
through a finite temperature differences. Tds equations, Availability in a steady flow system,
irreversibility and effectiveness. [6hrs]

Unit VI : Power cycles:

Gas power cycles: Otto cycle, Diesel cycle, semi-Diesel, Sterling cycles, their efficiency and mean
effective pressure calculations.
Vapors power cycles: Properties of steam, specific volume and entropy of steam, dryness fraction of
steam, throttling of steam, determination of dryness fraction, steam tables and their use, T-s and H-s
diagram, Rankine and modified Rankine cycle, work done and efficiency, specific steam consumption,
comparison of Rankine and Carnot cycle, representation on P-v, T-s and h-s diagram. [8hrs]

Text Books:
 Thermodynamics: An Engineering Approach, 3rd Edition, Yunus Çengel and Michael, Boles, Tata
McGraw Hill.
 Basic and Applied Thermodynamics, 2nd Edition, Nag P. K., Tata McGraw-Hill.

Reference Books
 Fundamentals of Thermodynamics, 5th Edition, Richard E. Songtag, Claus Borgnakke and
Gordon J. Van Wylen, John Wiley and Sons, Inc.
 Thermodynamics, 4th Edition, J.P. Holman, McGraw-Hill.
 Engineering Thermodynamics, 2nd Edition, Jones J.B. and Hawkins G.A., John Wyley and Sons.
 Fundamentals of Engineering Thermodynamics, Moran M.S. and Shapiro H.N., John Wyley and
Sons, 1988.
 Thermodynamics, 5th Edition, K. Wark, McGraw-Hill.

33
 (ME16002) Machine Drawing and Computer Graphics

Teaching Scheme: Examination Scheme:

Lectures : 2 Hrs/week T1 and T2: 20 Marks each
End-Sem Exam: 60 Marks

Course Outcomes:
Student will be able to
1. Learn the latest norms and standards about use of symbols and conventions abut Machine
Drawing and get aware about standard codes and drawing practices.
2. Obtain the limits, fits and tolerances for various assemblies and learn to indicate various
symbols on the machine drawing.
3. Develop the skills for drafting using CAD software and get the knowledge to enhance the CAD
utilities.

Unit I : Introduction to Machine Drawing:

Dimensioning Techniques, Representation of standard components such as Screw Threads, Screw
fasteners, keys, couplings, bearings, pulleys, brackets, gears, locking arrangements, Rivets and riveted
joints, Welding symbols.
Symbols for Pipe Joints, Expansion joints, stuffing box and glands, piping layouts, conventional
representation of pipe fittings, valves, joints, etc. [8hrs]

Unit II : Limits, Fits and Tolerances:

ISO system of tolerance, Tolerance charts, Hole - base and shaft -base system of tolerance, Types of fits,
symbols and applications.
Geometric Tolerances : Introduction, Nomenclature, Rules, Symbols, values obtained from various
manufacturing processes. [8hrs]

Unit III : Surface Roughness & Production Drawing :

Surface Textures, Roughness values and Roughness Grades, Machining symbols Conventional
Representation on part drawings.
Production Drawing: Assembly and part drawings, Blue print reading, study and preparation of bill of
materials. [6hrs]

Unit IV : Basic Drafting commands:

Drawing basic entities, Modify commands, Edit commands .. etc , Layers , Block attributes, Viewers,
Design center utilities , Solid Modelling , Editing of solids, 3-D operations such as shading and rendering
etc. [6hrs]

Unit V : Introduction to CAD programming :

Concept of parametric programming, Need and importance of CAD programming. Data types: Integers,
Real numbers, Strings, Symbols, Lists and File Descriptors. Data types conversions: Integer to real, string
list, real to integer, string lists. Reading and writing to the screen by using visual lisp consoles.
[6hrs]

34
Unit VI : Functions and Tools of CAD Programming :
Inputs in CAD Programming: Get functions for user input. Use of lists and the entities: Filtering from lists,
editing/ modifying the lists, entity managing and modifying the entities. Arithmetic and Logical
Functions: Additions, Subtraction, Multiplication, Division, sorting the data for deciding maximum and
minimum numbers, remainders, exponential operation, trigonometric functions, AND, OR etc. Decision-
making and looping, File handling functions (changing the properties of AutoCAD entities). Block
attributes and extracting the attribute data. [6hrs]

Text Books:
 K. L. Narayana, P. Kanniah, & K.V. Reddy, “ Machine Drawing ”, SciTech Publications (India Pvt.
Ltd.) Chennai
 Ajeet Sing, “Working with AutoCAD 2000”, Tata McGraw Hill
 George Omura , “ABC of Autolisp”, BPB Publications, New Delhi

Reference Books
 IS Code: SP 46 – 1988, Standard Drawing Practices for Engineering Institutes
 Auto CAD & Autolisp Manuals by AutoDesk Corp., USA
 “Design Data”, Faculty of Mechanical Engineering, PSG College of Tech, Coimbatore
 “Machine Drawing”, N.D.Bhatt and P.Kanniah, Charotar Pub. House, Anand, Gujrath
 “Computer Aided Engineering Drawing”, S. Trymbaka Murthy, I.K. International Publishing House
Pvt. Ltd, Pune

(ME 16003) Manufacturing Engineering - I

Teaching Scheme: Examination Scheme:

Lectures : 3 Hrs/week T1 and T2: 20 Marks each
End-Sem Exam: 60 Marks

Course Outcomes:
Student will be able to
1. Identify and explain the function of the basic components of machine tools and its accessories
2. Analyze various machining processes and select the particular manufacturing process for a given
job.
3. Have the knowledge of casting and forming process and solve the casting and forming problems.
4. Explain various surface treatment processes and its engineering applications.

35
Unit I : Hot and cold working of metals:
Principles of rolling, forging, drop, press, upset, roll forging, extrusion, drawing, spinning, and effect of
hot working. Cold working processes, Cold rolling, swaging, forging, extrusion- forward, backward and
impact roll forming, tube drawing, wire drawing, spinning, shot penning, high energy rate forming, sheet
metal working, types of presses, drives, different operations and types of dies. Forging design.
[6hrs]

Unit II : Joining processes:

Arc welding- Theory, SMAW, GTAW, GMAW, FCAW, Submerged arc welding, Stud welding Resistance
welding- Theory, spot and seam projection welding processes Gas welding Friction welding, Ultrasonic
welding, Thermit welding, EBW and LASER welding Use of adhesive for joining, classification of
adhesives, types of adhesive and their application, surface preparation and various joints welding
defects and quality. [7hrs]

Unit III : Foundry- Pattern making, moulding and casting:

Sand casting, types of pattern material, pattern making allowances, core print moulding, sand properties
and testing, hand and machine moulding, core boxes, core making, melting and pouring, melting
furnaces- Cupola, fuel fired, electric arc and induction furnaces. Cleaning, finishing and heat treatment
of casting, defects in casting lost foam processes, shell moulding and investment casting. Permanent
mould dies casting- Die-casting, low-pressure permanent mould casting, hot and cold chamber
processing, centrifugal casting, semi centrifugal casting and continuous casting. Gating system design,
Risering Design, product design for sand casting.
[8hrs]

Unit IV : Lathe and drilling Machine:

Turning and boring, lathe construction, accessories and operations. Thread cutting- single and multi
start threading, concept of speed, feed and depth of cut. Introduction to boring Machines, Capstan and
Turret lathe. Fundamentals of drilling processes, hoist, drill geometry, tool holder, types of drilling
machines, operations performed on drilling machines, type of drill. Reaming processes and reamer
types. [8hrs]

Unit V : Milling, shaping and planning:

Fundamental aspects, cutter types and geometry, Operations performed on milling machine, dividing
head method of indexing. Construction, working and operations performed on shaper, planer, and
broaching machines. [5hrs]

Unit VI : Grinding :
Wheels, wheel marking, wheel selection, wheel mounting, types of grinding machines. Honing, lapping,
super finishing, buffing and burnishing processes. [5hrs]

Text Books:
 K. L. Narayana, P. Kanniah, & K.V. Reddy, “ Machine Drawing ”, SciTech Publications (India Pvt.
Ltd.) Chennai
 Ajeet Sing, “Working with AutoCAD 2000”, Tata McGraw Hill
 George Omura , “ABC of Autolisp”, BPB Publications, New Delhi

36
Reference Books
 IS Code: SP 46 – 1988, Standard Drawing Practices for Engineering Institutes
 Auto CAD & Autolisp Manuals by AutoDesk Corp., USA
 “Design Data”, Faculty of Mechanical Engineering, PSG College of Tech, Coimbatore
 “Machine Drawing”, N.D.Bhatt and P.Kanniah, Charotar Pub. House, Anand, Gujrath
 “Computer Aided Engineering Drawing”, S. Trymbaka Murthy, I.K. International
Publishing House Pvt. Ltd, Pune

(ME 16004) Strength of Materials

Teaching Scheme: Examination Scheme:

Lectures : 3 Hrs/week T1 and T2: 20 Marks each
End-Sem Exam: 60 Marks

Course Outcomes:
Student will be able to
1. Apply basic concepts in structural mechanics to solve simple problems.
2. Determine the types of stresses developed in statically determinate member due to
3. different actions.
4. Analyze and design simple problems in engineering applications subjected to various actions.
5. Explain various surface treatment processes and its engineering applications.

Unit I : Simple stresses and strains:

a) Concept of stress and strain (linear, lateral, shear and volumetric) Hooks law. Elastic constants and
their relationship. Generalized Hook’s law.
b) Axial force diagram, stresses, strains and deformation in determinate and indeterminate
homogeneous and composite bars under concentrated loads, self weight and temperature changes.
[7hrs]

Unit II :
a) Shear force and bending moment diagrams
Concept and definition of shear force and Bending Moment in beams due to concentrated load, UDL,
uniformly varying loads and couples in determinate beams. Relation between SF, BM and intensity of
loading, SF, and BM diagrams for cantilevers, simple compound beams and bend.
b) Stresses due to bending
Theory of simple bending, concept and assumptions, Derivation of Flexure formula. Bending stress
distribution diagram. Moment of resistance and section modules calculations. [7hrs]

Unit III :
a) Shear stress distribution in beams
Shear stresses concept, derivation of shear stress distribution formulae, shear stress distribution
diagram for common symmetrical sections, maximum and average shear stress, shear connection
between Flange and web.
b) Torsion of circular shaft

37
Theory of torsion of shafts of circular, cross section. Assumptions, Derivation of torsion formulae,
stresses strains and deformation in determinate and indeterminate shafts of hollow, solid,
homogeneous circular cross section subjected to twisting moments, stresses due to combine torsion,
bending . [6hrs]

Unit IV :
a) Principal stresses and principal strain
Normal and shear stresses on any oblique planes and concept of principal planes and principal planes by
analytical and graphical methods (Mohr’s circle of stress 2-D).
b) Pressure Vessels.
Stresses, strains and deformation in thin walled seamless cylindrical and spherical vessels due to internal
fluid pressure. Change in volume, effects of additional fluid injected under pressure.
[6hrs]

Unit V : a) Axially loaded columns

Concept of critical load and buckling, derivation of Euler’s formulae for buckling load with hinged ends,
concept of equivalent length for various end conditions. Rankine’s formulae, safe load on column,
Limitations of Euler’s formulae.

b) Strain energy and impact.

Concept of strain energy, derivation and use of expressions for deformation of axially loaded members
under gradual sudden and impact loads. [5hrs]

Unit VI :Slope and Deflection of Determinate Beams

a) Concept and definition, relation between B.M., slope and deflection slope and deflection by double
integration method (McCauley’s method).
b) Slope and Deflection in determinate beams by Moment Area method [5hrs]

Text Book
 “Strength of Materials” By S. Ramamrutham & R Narayanan, Dhanpat Rai publication, New Delhi

Reference Books
 “Introduction to Mechanics of Solids” by J.B. Popov, Prentice – Hall publication
 “Mechanics of Materials” by James M.Gere (5th Edition) Brooks/Cole Thomson Learning.
 “Strength of Material” by F. L. Singer and Pytel, Harper and Row publication.
 “Mechanics of Material” by Beer and Johnston, Mc Graw Hill publication.

38
 (ME 16005) Machine Drawing and Computer Graphics Laboratory

Teaching Scheme: Examination Scheme :

Practical:4hrs/week Term work – 50 marks
Oral- 50 marks

Laboratory Outcomes:
At the end of the laboratory work, students will demonstrate the ability to:
Students will be able to
1. Utilize the knowledge of various ISO standards obtained in theory while attaining practical.
2. Use various standards, symbols, tolerances, limits and fits while drawing the sheets.
3. Communicate using software like AutoCAD and AutoLISP.

Term work:
Machine Drawing
1) One full imperial drawing sheet consisting the drawing/ sketches of representation of standard
components, symbols of pipe joints, weld joints, rivet joint etc, surface finish symbols &
grades, Limit, fit and tolerance related sketches.
2) One full imperial drawing sheet consisting of assembly and details of any one standard component
such as valves, components of various machine tools, pumps etc.

CAD Drawing and Programmes

I] Assignment of CAD drawings : -
a) Simple Orthographic Views, Orthographic Projections with three views of any one simple
machine component such as bracket, Bearing Housing or Cast component for Engines such as
Connecting rod, Piston etc and its’ 3-D model.
b) Isometric Views of machine components.
c) 3-D Models of machine components.

II ] Assignments of CAD programming:

1) Introductory programmes (minimum two on each) such as
a) Programmes to draw geometric figure or their combinations with changes in the type of
input required, for those figures. Such programmes should have use of arithmetic functions,
data conversions, filtering from lists.
b) Programmes to draw figures using Data type conversion involving users input data, blinking
on the screen use of trigonometry for solving graphics problems etc.
2) Parametric Programming (minimum two on each) such as
a) Program to draw a standard machine component by using decision-making and looping
statement of Autolisp.
b) Program to draw a profile, generated after getting data from user such as profile of cam,
profile of gear tooth, profile of points present on moving links or mechanisms etc.
3) Programme to enhance the capacity of CAD drawing
a) Making the File handling programmes
b) Obtaining animation of moving parts or mechanisms
c) Changing the Front page / display by Menu Customization Programme.
4) Innovative programmes of any type, by using Autolisp environment.

39
 (ME 16006) Manufacturing Engineering – I Laboratory

Teaching Scheme: Examination Scheme :

Practical: Practical:2 hr/week Term work – 50 marks
Oral- 50 marks
Laboratory Outcomes:
At the end of the laboratory work, students will demonstrate the ability to:
Get the knowledge of working of machine tools, mechanisms and accessories used in various
manufacturing processes
1. Perform the job of turning & taper turning operation using lathe
2. Perform Welding using gas/arc welding process
3. Solve the problems of Sand Casting and forming processes.
4. Explain CNC machines and their operations.
Termwork:
Each candidate shall be required to complete and submit the following term work:
 Jobs:
Plain and Taper turning – one job
Milling and Drilling – one Job
Forging and grinding of lathe tool with one knife and other end vee – one job
Welding (gas or arc) – one job
Sand Casting – one job
CNC Lathe Machine- Demonstration and hands on.
Journal:
Assignments on machine tools will be in the form of a journal based on demonstrations on machine
tools. This should include sketches and relevant descriptions as given below:
1) Block Diagrams (Any Two)
a) Lathe
b) Universal milling machine
c) Radial drilling machine
d) Cylindrical grinder.
2) Mechanisms (Any Two)
a) All geared headstock of a center lathe.
b) Spindle arbor (assembly) drive of milling machine
c) Crank and slotted lever quick return drive of shaping machine.
d) Spindle assembly in a drilling machine.
3) Accessories (Any Two)
a) Taper turning attachment for a centre lathe.
b) Universal dividing head.
c) Milling cutters.
CNC Lathe machine working and operations.

40
 (ME 16007) Strength of Materials Laboratory

Teaching Scheme: Examination Scheme :

Practical: Practical:2 hr/week Term work – 50 marks
Oral- 50 marks

Laboratory Outcomes:
Students will be able to
1. Utilize the knowledge obtained in theory in order to perform practical.
2. Analyze the effect of tensile, shearing force and can utilize the knowledge gained while tackling
real life engineering problems.
3. Incorporate the important concepts learnt while designing components.

List of Experiments:
1. Tension test on Mild Steel and Aluminum
2. Shear test on Mild Steel and Aluminum
3. Torsion test on Mild Steel and Cast-Iron
4. Impact test on Mild Steel, Aluminum and Cast-Iron
5. Hardness test on Mild Steel, Aluminum and Cast iron
6. Bending test on Timber, Plywood and Mild Steel.
7. Bend- rebend test on mild steel and Torsteel
8. Flexure test on Mild Steel.

Semester III (For Direct Second Year Admitted Diploma Students)

(MA- ) Linear Algebra and Calculus

Teaching Scheme: Examination Scheme:

Lectures : 4hrs / week T1 and T2: 20 Marks each
Tutorial : 1 hr End Sem. Exam: 60 marks

Course Outcomes:
Students will be able to
1. Know and recall the core knowledge of the syllabus. ( To measure this outcome, questions may
be of the type- define, identify, state, match, list, name etc.)
2. Understand the concept. ( To measure this outcome, questions may be of the type- explain,
describe, illustrate, evaluate, give examples, compute etc.)
3. Analyze the problem and apply the appropriate concept. ( To measure this outcome, questions
will be based on applications of core concepts)

41
 4. Apply core concepts to new situations. ( To measure this outcome, some questions will be
based on self-study topics and also comprehension of unseen passages.)
5. Give reasoning. ( To measure this outcome, questions may be of the type- true/false with
justification, theoretical fill in the blanks, theoretical problems, prove implications or corollaries
of theorems, etc.)

Unit I:
Matrices and linear equations: basic properties of matrices, row operations and Gauss elimination,
Determinants and their basic properties. Basic concepts in linear algebra: vector spaces, subspaces,
linear independence and dependence of vectors, bases, dimensions. Row and Column spaces, rank.
Applications to systems of linear equations. [14hrs]

Unit II:
Linear mappings, representation by matrices, rank-nullity theorem, Eigen values, Eigen vectors and their
basic properties, diagonalization. [12hrs]

Unit III:
Review of limits, continuity and differentiability, Mean value theorems, Taylor's theorem, local
extrema, increasing and decreasing functions, concavity, points of inflection. [10hrs]

Unit IV:
Integrals as limits of Riemann sums, fundamental theorem of calculus, surface area, integrals by special
techniques: reduction formulae, arc length, solids of revolution, improper integrals, tests for
convergence, Gamma and Beta functions. [12hrs]

Text Books :
 Advanced Engineering Mathematics (9th edition) by Erwin Kreyszig, Wiley eastern Ltd
&Bombay, 2006.
 Thomas’ Calculus (12th edition) by Maurice D. Weir, Joel Hass, Frank R. Giordano, Pearson
Education, 2008.

Reference Books :
 Linear Algebra by Hoffman and Kunze, (2nd edition) Prentice Hall Publication, New Delhi.
 Higher Engineering Mathematics by B. V. Ramana ,Tata McGraw Hill .
 Advanced Engineering Mathematics by C.R. Wylie, McGraw Hill Publications, New Delhi.
 Advanced Engineering Mathematics (7th edition ) by Peter V. O’ Neil, Thomson.Brooks/ Cole,
Singapore.
 Differential Calculus by Shanti Narayan, S. Chand and company, New Delhi.
 Engineering Mathematics (Volume-I) by S. S. Sastry, Prentice Hall Publication, New Delhi.
 Higher Engineering Mathematics by B.S.Grewal, Khanna Publications, New Delhi.

42
 (PH 16001) Foundation of Physics
(For Direct Second Year Admitted Diploma Students)

Teaching Scheme : Examination scheme:

Lectures:3 hrs /week Test 1 & 2: 20 marks each
End Sem exam: 60 Marks
Course Outcomes:
At the end of the course student should be able to
a) Develop the understanding of laws of thermodynamics and their application in
various processes, optics and their applications.
b) Solve the basic problems in Classical Mechanics
c) Derive the Wave Mechanics of microscopic bodies.
d) Formulate and solve the engineering problems on Electromagnetism.

Unit 1 Thermodynamics (6 hrs)

i) Heat as a form of energy , mechanical equivalent of heat, thermodynamic
systems,
ii) Zeroth law and concept of temperature, first law & its mathematical statement,
iii) Second law and concept of entropy, third law of thermodynamics,
v) Concept of free energy; Gibbs and Helmoltz free energy.

Unit 2 Waves motion & Optics (6 hrs)

i) Logitudinal and transeverse waves, Light as an EM wave and it’s graphical
representation,
ii) General equation of traveling wave,
iii) Superposition principle, formation of stationary waves (with derivation),
iv) Huygen's Principle, Young’s double slit experiment,
v) Interference of light due to thin film of uniform thickness and conditions for
darkness and brightness,
vi) Diffraction due to a single slit; conditions of maxima and minima.

Unit 3 General Mechanics (6 hrs)

i) Kinetic energy and potential energy,
ii) Work done (single particle system only); work energy theorem,
iii) Conservative and non conservative forces, concept of central force, properties of
central force,
iv) Laws of planetary motion (with mathematical statement).

Unit 4 Introduction to Quantum Mechanics (6 hrs)

i) Drawbacks of classical mechanics, Plank’s quantum hypothesis, Dual nature of
matter,
ii) De Broglie’s hypothesis, de Broglie’s wavelength,

43
 iii) Photoelectric effect, Davisson-Germer’s experiment,
iv) Heisenberg's uncertainty principle
v) Illustrations of Heisenberg's uncertainty principle; electron diffraction at a single
slit

Unit 5 Electrostatics (6 hrs)

i) Coulomb's law in integral form, the electric field intensity ,
ii) Continuous charge distribution (Line, Surface & Volume),
iii) Introduction to Gauss's law, integral form of Gauss's law,
iv) Applications of Gauss's Law to simple 2D-3D problems ,
v) Line integral of electric field, concept of electric potential (V),
vi) Potential (V) due to continuous charge distribution.

Unit 6 Magnetostatics (6 hrs)

i) Steady currents ( line current ,surface current,volume current) & current densities,
ii) Magnetic field due to steady currents (Biot-Savert’s law) and it’s applications,
iii) Line integral of B over a closed loop,
iv) Ampere's Law and its applications to simple problems,
v) Closed surface integral of B (Non-existence of magnetic monopole).

References:
Unit 1: H. C. Verma & Halliday-Resnick (Sixth edition), B. B. Laud
Unit 2: Halliday-Resnick (Sixth edition )
Optics by Brij Lal (S. Chand Publication)
Unit 3: Classical Mechanics by P. V. Panat,
H. C. Verma, Halliday –Resnick (Sixth edition)
Unit 4: Halliday-Resnick (Sixth edition)
Unit 5 & 6: Classical Electrodynamics by David Griffith (Pearson India limited)

44
 Semester-IV

(MA 16002) Vector Calculus and Partial Differential Equations

Teaching Scheme: Examination Scheme:

Lectures : 2 Hrs/week T1 and T2: 20 Marks each
Tutorial: 1Hr/week End-Sem Exam: 60 Marks

Course Outcomes:
Students will be able to:
1. Know and recall core knowledge of the syllabus. (To measure this outcome, questions may be of
the type- define, identify, state, match, list, name etc.)
2. Understand basic concepts. (To measure this outcome, questions may be of the type- explain,
describe, illustrate, evaluate, give examples, compute etc.)
3. Analyze the problem and apply the appropriate concept. (To measure this outcome, questions
will be based on applications of core concepts)
4. Give reasoning. (To measure this outcome, questions may be of the type- true/false with
justification, theoretical fill in the blanks, theoretical problems, prove implications or corollaries
of theorems, etc.)
5. Apply core concepts to new situations. (To measure this outcome, some questions will be based
on self-study topics and also comprehension of unseen passages.)
6. Organize and present thoughts. (To measure this outcome, questions may asked to write
summaries and short notes on a given topic.)

Unit I :
Vector differentiation, gradient, divergence and curl, line and surface integrals, path independence,
statements and illustrations of theorems of Green, Stokes and Gauss, arc length parameterization,
applications. [9hrs]

Unit II :
Partial differential equations with separation of variables, boundary value problems: vibrations of a
string, heat equation, potential equation, vibrations of circular membranes. [10hrs]

Unit III :
Laplace Transforms, its properties, Unit step function, Dirac delta functions, Convolution Theorem,
periodic functions, solving differential equations using Laplace transform. [7hrs]

Text Books:
 Maurice D. Weir, Joel Hass, Frank R. Giordano, "Thomas’ Calculus", Pearson Education, 12th
Edition.
 Erwin Kreyszig, "Advanced Engineering Mathematics", Wiley eastern Ltd., 10th Edition.

45
Reference Books:

 C.R. Wylie, “Advanced Engineering Mathematics” , McGraw Hill Publications, New Delhi.
 Peter V. O’ Neil, “Advanced Engineering Mathematics”, Thomson Brooks / Cole, Singapore, 7th
edition.
 Wendell Fleming, “Functions of several variables”, Springer-Verlag, New York.
 Fritz John, “Partial Differential Equations” (4th edition), Springer.
 Michael D. Greenberg, “Advanced Engineering Mathematics (2nd edition)”, Pearson Education.

(ML 16001) Professional Ethics and Values

Teaching Scheme: Examination Scheme:

Lectures : 1hr / week T1 and T2: 20 Marks each
End Sem. Exam: 60 marks

Course Outcomes:
1. To create awareness about Professional Ethics and Human Values.
2. To enable future professional engineers to contribute to societal and human well-being.
3. To inculcate professional behaviour and sound work / workplace ethics in young minds.
4. To inculcate social responsibility at the personal, professional and corporate levels.
5. To appreciate the concept of gender diversity and related issues from an ethical
viewpoint.
6. To appreciate and deal with ethical dilemmas while discharging duties in professional life.

Unit I :
Morals, Values and Ethics ,Integrity, Work Ethic, Honesty ,Commitment Courage ,Empathy ,Self-
Confidence, Character, Caring and Sharing Empathy and Leadership. [4hrs]

Unit II :
Introduction to and history of Ethics,Profession and professionalism ,Professional roles played by an
engineer,Engineering ethics (supported by case studies),Moral / ethical dilemma, moral autonomy,
consensus and controversy, etc.Codes of conduct and codes of ethics, Gender diversity at the
workplace, women’s empowerment, sexual harassment. [5hrs]

Unit III :
Types of technology and their ethical application, Transfer of technology, its benefits and drawbacks,
Role of multinational corporations in technology transfer, Environmental ethics and need for sustainable
development, Environmental hazards due to irresponsible technological development,Computer ethics
and IPR, and computer crime ,Social problems resulting from.
[6hrs]

Unit IV :
Meaning of experimentation in engineering, Engineers’ role as responsible social experimenters to
benefit society, R&D efforts towards ethically and environmentally sustainable design of products and
systems, A balanced view towards legal, ethical and business aspects of technology use. [5hrs]

46
Unit V :
Knowledge of safety and risk and the ethical need to reduce it, Uncertainty of design, Need for testing
product and system designs for safety, Concept of risk benefit analysis, Ethical issues in cost-benefit
analysis, Protecting employee rights, human rights and human responsibilities, Case studies involving
natural and manmade disasters, (e.g. Chernobyl, Bhopal Gas Tragedy, floods in Uttarakhand, Kashmir,
etc. [5hrs]

Unit VI :
Meaning and brief history of whistle blowing, Internal and external whistle blowing,Ethical and legal
issues involved in whistle blowing, Managing whistle blowing, Case studies involving whistle blowers like
Manjunath, SatyendraDubey, etc. [3hrs]

(HS 16001) Innovation

Teaching Scheme: Examination Scheme:

Lectures : 1 Hr/week "To be declared by the Instructor"

Course Outcomes:
At the end of the Course, Student will be able to:
1. Discover the creative / innovative side within herself/himself.
2. Hone entrepreneurial and leadership skills within his/her personality.
3. Develop new ways of thinking and Learn the entire innovation cycle from Ideation to Go-To-
Market.
4. Study frameworks, strategies, techniques and business models for conceived ideas.
5. Develop skills for evaluating, articulating, refining, and pitching a new product or service.

Syllabus:
Introduction to Innovation, Personal thinking preferences, ‘Innovation’ mind set, Everyday
creativity and eliminating mental blocks, Introduction to Innovation, Creative thinking
techniques, Innovation types, Idea management and approaches, Teaming techniques for
creativity, Idea Conception, Idea Scoping, Self Evaluation, Idea Brainstorming sessions, Idea
Verification, Market Evaluation, Concept Evaluation, Idea Verification, Prototype Evaluation,
Protection/Patent review, Innovation Case Study, Idea Presentations, Idea Incubation, Product
and Market Plan, Product and Market Development, Innovation Case Studies, Idea Incubation
and Product Launch, Marketing and selling, Post Launch Review

Reference Books:
 Jeff Dyer, Hal Gregersen, Clayton M. Christensen, " The Innovator's DNA: Mastering the Five
Skills of Disruptive Innovators, Harvard Business Review Press, 2011.
 Paddy Miller, Thomas Wedell-Wedellsborg, "Innovation as Usual: How to Help Your People Bring
Great Ideas to Life , Harvard Business Review Press, Kindle Edition.

47
 (ILOE) Automobile Engineering

Teaching Scheme: Examination Scheme:

Lectures : 3hrs / week T1 and T2: 20 Marks each
End Sem. Exam: 60 marks

Course Outcomes:
Student will be able to
1. Implement the knowledge obtained in theory towards design and analysis of various automobile
systems.
2. Comprehend various aspects of automobile system for enhancement of comfort, safety and
economics the various automobile
3. Repair and maintain the automobile

Unit I :
Introduction: Vehicle specifications, classifications, Engine cylinder arrangements, Power requirements,
motion resistance and power loss; tractive efforts.
Chassis layout, frame, main components of automobile and articulated vehicles. Design considerations,
materials and their properties. [6hrs]

Unit II :
Transmission System : Clutches: need, types. Need of gearbox, types of gear transmission, shift
mechanisms, over running clutch, fluid coupling, and torque converters. [6hrs]

Unit III :
Transmission universal joint, constant velocity joint, propeller shaft, Hotchkiss drive, torque tube drive,
front and rear axles types, stub axles, need of differential and types, four wheel drive. [6hrs]

Unit IV :
Steering and Suspension Systems: Steering system, principle of steering, centre point steering, steering
linkages, steering geometry and wheel alignment, power steering.
Suspension system: need, types, independent suspension, coil and leaf springs, suspension
systems for multi, axle vehicles, trouble shooting and remedies. [8hrs]

Unit V : Brakes:
Need, types, mechanical, hydraulic and pneumatic brakes, disc and drum types, their relative merits,
details of components, brake adjustments and defects, power brakes.
Wheels and Tyres: Types, tyre construction, specification, tyre wear and cause, wheel balancing.
[6hrs]

Unit VI : Electrical Systems:

Electrical systems construction, operation and maintenance of lead acid batteries battery charging
system principle and operation of cutout and regulators starter motor Bendix drive solenoid drive
magneto coil and solid stage ignition systems, ignition timing, lighting, and electrical accessories,
automobile air conditioning, panel board instruments. [8hrs]

48
Text Books:
 Automobile Engineering by Dr. Kirpal Singh (Vol. I & II ) Standard Publishers 1999
 Automobile Engineering by G.B.S. Narang.1999

Reference Books:
 Automotive Technology by H.M. Sethi.1990
 Automobile Engineering by Banga & Singh,1990
 Joseph Heitner„ Automotive Mechanics‟, 2nd Ed., Affiliated Eastern Law house, 1967.
 Dolan. J.A., „Motor Vehicle Technology and Practical Work‟, ELBS, 1978
 Motor Vehicles, Newton & Steed
 Motor Manuals (Vol I to VII), A.W. Judge.
 Automobile Mechanics, W.H. Crouse. McGraw Hill publishing Co 2005

(ILOE) Smart Materials

Teaching Scheme: Examination Scheme:

Lectures : 3hrs / week T1 and T2: 20 Marks each
End Sem. Exam: 60 marks

Course Outcomes:
Student will be able to
1. Get introduce to the latest basic concepts and informations.
2. Know the applications of a range of smart materials.
3. Design and develop the smart system for the specific application.

Unit I : Introduction to smart materials

Various types of smart material and its need in advanced manufacturing processes, Smart material's
properties, The development of smart materials and structures. [8hrs]

Unit II : Various Types and Manufacturing Methods

Manufacturing techniques for each smart material such as Deposition, Ion Implantation, Coatings for
high temperature performance, Electrochemical and spark discharge and Plasma coating methods,
Electron beam and laser surface processing, Organic and Powder coatings, Thermal barrier coating.
[10hrs]

Unit III : Alloys

Shape memory alloys, Superalloys, creep resistance, Ultra high strength steels, Amorphous alloys,
Zirconium alloys, Light metal alloys and synthesis by mechanical alloying. [6hrs]

Unit IV : Polymers and Composites

Polymers and their synthesis, polymer curing. Conductive polymers and elastomers. Electroactive
polymers, electrostrictive materials and Piezoelectric materials, Ceramic materials.
Smart composites and Metal matrix composites (MMC). [8hrs]

49
Unit V : Bio-Materials
Nano materials, Nanostructures, gels, coatings, LB films, electrochromic sol-gel coatings. Metallic
glasses,
Magnetic materials. Magnetostrictive materials, magnetorheological fluids, electrorheological materials
and their applications.
Design of smart systems and practical applications such as aerospace and automobiles. [8hrs]

Text Books :
 Engineering analysis of smart material systems , Donald J. Leo, John Wiley Sons.
 Smart material systems: model development, R.C. Smith, SIAM Edition

Reference Books:
 Addington, M. , Schodek, Daniel L.: Smart materials and new technologies, Architectural Press,
2005
 Polymer I.J., “Light Alloys & Metallurgy of light metals”, Arnold Press,1995.
 Schwartz, M: Encyclopedia of Smart Materials, Volumes 1-2 ,Willey 2002
 Westbrook J.H & Fleischer R.L., “Intermetallic compounds VOL I & II”, John Wiley, Chichester ,1995
 Smallman and Bishop, “Metals and Material Science, process, applications”
 Clyne T.W. & Withers P.J., “An Intro. to metal matrix composite”, Cambridge University Press,
1993.
 Artz & L. Schulte (Ed), “New Materials by mechanical alloying techniques”, DGM.

(ILOE) Computer Aided 3 D Geometric Modelling

Teaching Scheme: Examination Scheme:

Lectures : 3hrs / week T1 and T2: 20 Marks each
End Sem. Exam: 60 marks
Course Outcomes:
Student will be able to
1. think logically & understand the basic concepts of solid modeling
2. to apply knowledge of mathematics, science, and engineering while creating parametric
geometric model
3. create 3D model using any professional software
4. create assembly model using any professional software
5. generate 2D part and assembly drawings with BOM details using any professional software
6. interface 3D part model with program to automate design process

Unit I : Geometric Modeling:

Introduction to CAD/CAM, 2D vs 3D Geometric model, Introduction to Wireframe, surface and solid
modeling techniques. Geometry vs Topology, Requirements of Geometric Modeling, Geometric
Modeling Methods: Constructive Solid Geometry (CSG), Boundary Representation (B-rep), Feature based
Modeling, Direct (History less) Modeling, behavior modeling, 3D scan modeling. [6hrs]

50
Unit II : Parametric solid modeling:
Fundamentals, apply/modify constraints and dimensions, transform the parametric 2-D sketch into a 3D
solid. Introduction to Graphical User Interface (GUI) of any commercially used solid modeling software.
Create 3D model using Sketch features and Placed features. [8hrs]

Unit III : Advance Features:

3D modelling using Modifying and copying featurs. Use of datum featres: Datum points, axis, curve,
planes etc. Parametric equation of various curves. [8hrs]

Unit IV : Assembly modeling

Defining relationship between various parts of machine, creation of constraints, generation of exploded
view. [6hrs]

Unit V : Production drawing

Generation of 2-D sketches from parts and assembly 3-D model, appropriate dimensioning and
tolerancing. Introduction to design automation by interfacing CAD software to Higher level languages.
[8hrs]

Text books:
 Ibrahim Zeid, Mastering CADCAM, McGraw-Hill
 Help manuals and tutorials of professional CAD software

References books:
 N. D. Bhatt and V.M. Panchal, Machine Drawing, Charoter Publications
 ASME Y14.5 – 2009

(ME 16008) Theory of Machines- I

Teaching Scheme: Examination Scheme:

Lectures: 3 hrs/week T1 and T2: 20 Marks each
End Sem. Exam: 60 marks

Course Outcomes:
Students will be able to;
1. Determine kinematic analysis (Velocity, acceleration, Inertia forces) for a given of a given
mechanism using analytically and graphically method.
2. Demonstrate the dynamics of cams and followers, governors, and their characteristics.
3. Draw inversions and determine velocity and acceleration of different mechanisms.
4. Construct different types of cam profile for a given data.
5. Solve and determine forces and dimensions of Spur and Helical Gear.
6. Calculate speeds and study performance of various types of Gyroscope.

51
Unit I: Fundamentals of kinematics and mechanisms:
Kinematic link, Types of links, Kinematic pair, Types of constrained motions, Types of Kinematic pairs,
Kinematic chain, Types of joints, Mechanism, Machine, Degree of freedom (Mobility), Kutzbach
crieterion, Grubler’s criterion, Inversion, Four bar chain and its inversions, Grashoff’s law, Slider crank
chain and its inversions, Double slider crank chain and its inversions, straight line mechanisms,
pantograph, Geneva mechanism, steering gear mechanisms, Hooke’s joint, Introduction to Compliant
mechanism. [8hrs]

Unit II: Velocity and acceleration analysis:

Relative velocity acceleration methods, Corioli’s component of acceleration, instantaneous center of
Rotation method, Kennedy theorem of three center in line, body and space centrode, Klein’s
construction, Position analysis of links with vector and complex algebra methods, Loop closure equation,
Chace solution, Velocity and acceleration analysis of mechanisms using vector and complex algebra
methods. [8hrs]

Unit III: Static and dynamic force analysis of slider crank mechanism:
Analytical method for displacement, velocity and acceleration of slider crank mechanism, D’Alembert’s
principle, static and dynamic force analysis of slider crank mechanism, dynamically equivalent system,
correction couple, graphical and analytical method for determination of torque on crankshaft.
[8hrs]

Unit IV: Theory of Gears I:

Classification of gears, Types of gears, Spur gears - terminology, fundamental law of toothed gearing,
involute and cycloidal profile, conjugate action, contact ratio, minimum number of teeth, interference
and under cutting. Helical gears: Nomenclatures, center distance, force analysis.
[8hrs]

Unit V: Cams and followers:

Types of cams and followers, types of follower motion, velocity and acceleration diagrams, profile of
cam cams with specified contours. [6hrs]

Unit VI: Governor Mechanisms:

Introduction, Types, Governor Effort and governor power, Controlling force analysis, sensitivity, stability,
isochronisms and hunting, friction, insensitiveness [6hrs]

Text Books:
 Ballaney, P., “Theory if Machines and Mechanisms”, 2005, ISBN 9788174091222 / 817409122X
Khanna Publications
 John Hannah and Stephens, R. C., “Mechanics of Machines: Advanced Theory and Examples”,
1970, Hodder; Student international edition, ISBN 0713132329 Edward Arnold London

Reference Books:
 Uicker Jr, J. J., Penock G. R. and Shigley, J. E., “Theory oif Machines and Mechanisms’ 2003, Tata
McGraw Hill.
 Ramamurthy V., “Mechanisms of Machines”, 3rd edition, ISBN 978-1842654569, Narosa
Publishing House.
 Bevan Thomas, “The Theory of Machines”, 3rd edition, CBS publication.

52
  Bansal, R. K., “Theory of machines”, Laxmi Publications Pvt. Ltd, New Delhi

(ME 16009) Fluid Mechanics

Teaching Scheme: Examination Scheme:

Lectures : 2 hrs/week T1 and T2: 20 Marks each
Tutorials: 1 hr/week End Sem. Exam: 60 marks

Course Outcomes:

Student will be able to

1. Solve problems involving fluid properties and be able to calculate hydrostatic forces on various
types of surfaces.
2. Obtain the solution of the problems dealing with dam gates, ship stability, buoy stability etc.
3. Apply and analyze fluid systems using the integral form of the continuity, momentum,
4. Apply Bernoulli’s Equation for various fluid systems and flow measuring devices.
5. Apply and understand various dimensionless numbers for problems in fluid mechanics
6. Analyze and explain physical significance of flow through the pipes.
7. Derive governing equations and study various parameters for turbulent flows.

Unit I : Basics with fluid statics:

Definition of fluid, fluid properties such as viscosity, vapor pressure, compressibility, surface tension,
capillarity, Mach number etc, pressure at a point in the static mass of fluid, variation of pressure,
Pascal’s law, pressure measurement by simple and differential manometers using manometric
expression.
Hydrostatic forces on the plane and curved surfaces, centre of pressure, Buoyancy, centre of buoyancy,
stability of floating bodies, metacentre and metacentric height and its application in shipping.
[6hrs]

Unit II : Fluid Kinematics:

velocity of fluid particle, types of fluid flow, description of flow, continuity equation, Coordinate free
form, acceleration of fluid particle, rotational & irrotational flow, Laplace’s equation in velocity potential
and Poison’s equation in stream function, flow net. [4hrs]

Unit III : Governing equations in Fluid Dynamics:

Derivation of Momentum equations using integral
and deferential approach, dimensionless form of governing equations, special forms of governing
equations, Integral quantities. [4hrs]

Unit IV : Applications of Bernoulli’s Equation and Flow through pipes:

(a) Integration of Euler’s equation to obtain Bernoulli’s equation, Bernoulli’s theorem, Application of
Bernoulli’s theorem such as venture meter, orifice meter, pitot tube and orifices etc
(b) Reynolds’s experiment, frictional loss in pipe flow, major and minor losses, HGL and TEL, flow
through series and parallel pipes. [4hrs]

53
Unit V :
a) Dimensional homogeneity, Raleigh’s method, Buckingham’s theorem, Model analysis, similarity laws
and dimensionless numbers.
(b) Introduction to boundary layer theory and its analysis.
(c) Forces on Submerged bodies: Drag, lift, Drag on cylinder, Development of lift in Cylinder.
[4hrs]

Unit VI :Turbulent Flow:

Characteristics of turbulent flow, laminar turbulent transition, time mean motion and fluctuations,
derivation of governing equations for turbulent flow, shear stress models, universal velocity
distribution. [4hrs]

Text Books :
 Fluid Mechanics, Vijay Gupta, Narosa Publications, 2014
 Advanced Fluid Engineering, Murlidhar and Biswas, Narosa Publications
 Mechanics of Fluids, Irwin Shames, McGraw Hill, 2003
 Hydraulics and Fluid Mechanics including Hydraulic Machines, Dr. P. N. Modi and Dr. S. M. Seth,
Standard Book House

Reference Books:
 Fluid Mechanics, P. K. Kundu , I. M. Kohen and David Dowling Fifth Edition Elsevier Publication.

(ME 16010) Fundamentals of Metallurgy

Teaching Scheme: Examination Scheme:

Lectures :3hrs/ week T1 and T2: 20 Marks each
End Sem. Exam: 60 marks

Course Outcomes:
1. Able to demonstrate an understanding of the structure-property-processing correlation
engineering materials.
2. Able to select appropriate mechanical testing for various metallic materials.
3. Able to distinguish among various types of steels and cast irons for particular application.
4. Able to select appropriate heat treatment for metals and alloys for particular application.

Unit I :
Engineering Materials
Overview of Metallic Materials: Ferrous and Non Ferrous Metals, Ceramics- Traditional and Engineering
Ceramics, Polymers: Traditional and Special Polymers, Composites: Ceramic- Metal- Polymer
composites, Carbon nano tube composites. [6 hrs]

54
Unit II :
Plain Carbon and Alloy Steels
Type of equilibrium diagrams in metals and alloys, lever rule. Iron - Carbon equilibrium diagram, critical
temperatures. Allotropy, cooling curve and volume changes of pure iron. Microstructures of slowly
cooled steels, estimation of carbon from Microstructures, non-equilibrium cooling of steels, Effects of
alloying elements and examples of alloy steels. Stainless steels. Tool steels and tool materials.
Applications of plain carbon and alloy steels, specifications of some commonly used steels for
engineering applications (e.g. En, DIN, IS etc with examples) [8 hrs]

Unit III : Heat Treatment of Steels

Transformation products of austenite, Time temperature Transformation diagrams, Critical cooling rate,
continuous cooling transformation diagrams. Heat treatment of steels, Cooling media. Annealing,
normalizing, hardening. Tempering, Carburising, Nitriding, carbonitriding, Flame and Induction
hardening. Commercial heat treatment practice of gears of different sizes, tools, lathe beds, springs, etc.
[10 hrs]

Unit IV : Cast Irons

Classification of Cast irons Gray cast irons, nodular cast irons, white cast irons, malleable cast irons,
chilled. Effect of various parameters on structure and properties of cast irons. Applications of cast irons
for different components of machine tools, automobiles, pumps, etc. [6 hrs]

Unit V : Mechanical Testing

Tension test - Engineering and true stress strain curves, Compression test, Hardness Tests: Brinell,
Rockwell, Vickers, Hardness conversions, Impact test, Non Destructive Testing: Magnetic Particle test,
Dye penetrant, ultrasonic tests, radiography and eddy current testing. [6 hrs]
Unit VI : Powder Metallurgy
Sintered structural components, Advantages and Limitations of powder metallurgy, powder
manufacture, testing and characterization, Manufacturing of typical P/M products : cemented carbides,
cermets, sintered carbide cutting tools, diamond impregnated tools , sintered metal friction materials
and self lubricating bearings. [6 hrs]

Text Books:
 D. R. Askland & P. P. Phule, “Material Science & Engineering of Materials”, by Cengage Learning
Center India Pvt Ltd. , Sixth Indian Edition, 2011
 R. A. Higgins, Engineering Metallurgy Part-I, Applied Physical Metallurgy, ELBS with Edward
Arnold, Sixth Edition 1993.
 S.H. Avner, Introduction to Physical Metallurgy , Tata Mac Graw Hill, Second edition, 1997.

Reference Books:
 V. Raghvan, “Materials Science & Engineering”, PHI 5th Edition, Prentice-Hall of India (P) Ltd.
 W. Callister, “Materials Science & Engineering”, John Wiley & sons
 Clark D. S. and Varney W. R., “Physical Metallurgy for Engineers”, Affiliated East-West Press,
New Delhi.
 R. Balasubramaniam , Callister's Materials Science and Engineering, Wiley India Pvt Ltd., 2008.
 K. Bhargava , Mechanical Behaviour and Testing of Materials by and C. P. Sharma, Publication
PHI 2011.

55
 (ME 16011) Manufacturing Engineering II

Teaching Scheme: Examination Scheme:

Lectures : 3hrs / week T1 and T2: 20 Marks each
End Sem. Exam: 60 marks

Course outcome
Students will be able to
1. Demonstrate various non conventional manufacturing processes and select proper process for
the purpose of manufacturing.
2. Develop competency for selecting appropriate machining process depending on desired output
characteristics such as MRR, surface finish.

Unit I : Sheet metal working

Introduction to sheet metal working, press-types and main parts of power press, die details and
accessories, metal cutting in a punch and die set up, die details and accessories, types of dies,
clearance, angular clearance, various press operations, strip layout, centre of pressure, cutting forces,
methods of reducing cutting forces, Blanking die design, drawing- blank size calculations, number of
draws, drawing force, Bending- Bend allowance, bending force calculations [6 hrs]

Unit II : Theory of metal cutting

Mechanics of chip formation, oblique and orthogonal cutting, single point tool geometry, types of chips,
cutting ratio, shear plane angle, velocities in cutting, Merchant circle, shear strain, power in cutting,
cutting tool materials, cutting fluid, machinability, evaluation of machinability, optimum cutting speed,
tool life, factors affecting tool life, computation of tool life. [7 hrs]

Unit III : Non conventional methods of machining

Need of nonconventional methods of machining, classification of non conventional methods of
machining, Operating principle, process parameters, advantages, disadvantages and applications of any
four non conventional methods of machining which uses different forms of energy. [6 hrs]

Unit IV : Jigs and fixtures

Introduction to jigs and fixtures, need, 3-2-1 principle of location, various locating devices, cavity
location, redundancy in location, fool proofing, clamping devices, general guidelines for design of
jig/fixtures. Design of jig for simple component, design of milling fixture for simple component. [7 hrs]

Unit V : NC, CNC, DNC

Introduction to CAD/CAM, NC-Basic components, procedure, coordinate system, motion control,
applications, merits and problems, CNC-types, functions and advantages, DNC- Types, functions and
advantages. Introduction to adaptive control, FMS and machining centre.

56
Surface treatment processes
Introduction to surface engineering, surface structure and properties, surface texture, need of surface
treatment processes, various types of surface treatment processes, Introduction to any four surface
treatment processes such as peening, burnishing, heat treatment etc. [7 hrs]

Unit VI : Broaching
Broach-geometry/elements, principle, Types of broaching machines, comparison of broaching with
other processes, applications, broach design.
Gear manufacturing
Gear manufacturing by forming processes, gear generating processes such as gear shaping, hobbing,
milling, hobbing, Gear finishing processes- shaving, roll finishing, grinding, lapping [6 hrs]

Text Books
 Chapman, “Workshop technology” Vol. I, II & III; Edward Arnold Publications Ltd. London.
 Hajara Chaudhary S. K., “Workshop Technology” Vol. I & II, Media Prom & Publication, Mumbai.
 R. K. Jain, “Production Technology”; Khanna Publications
 Hoffman, “Introduction to Jigs and fixtures”, Galgotia Publishers

Reference Books
 S. K. Basu, “Fundamentals of Tool design”, Tata Mcgraw Hill Education Private limited.
 Serope Kalpakjian & Steven R. Schmid, “Manufacturing processes for engineering materials
 HMT Hand book “Production technology”, Tata Mcgraw Hill Education Pvt. Ltd.
 S. E. Rusinoff, “Manufacturing processes”, Times India Press.
 Doyle, “Manufacturing processes and materials for engineers”, Prentice Hall of India Press

(ME 16012) Theory of Machines– I Laboratory

Teaching Scheme: Examination Scheme:

Lectures : 2hrs / week Term Work: 50 marks
Oral: 50 marks

Course Outcomes:
Students will be able to
1. Demonstrate knowledge of various mechanisms in order to design and analyze mechanisms
essential in mechanical engineering.
2. Demonstrate ability towards graphically estimating velocity and acceleration.
3. Exhibit skills towards application of principles of static and dynamics force analysis.
4. Knowledge attained will comply towards successfully addressing issues relating to gears,
governors, cams and followers in real life engineering problems.

List of Experiments:
1. Determination of moment of inertia of rigid bodies by bifilar/trifilar suspension methods.
2. Compound pendulum.

57
 3. Experimental verification of displacement relation for different shaft angles for single Hooke’s
joint.
4. To generate gear tooth profile and to study the effect of under cutting and rack shift using
model.
5. To determine the characteristics curve of any two type of centrifugal governor and to find its
coefficient of insensitiveness and stability.

List of Assignments:
1. Velocity and acceleration by vector and complex algebra method
2. Analytical determination of inertia forces in engine mechanisms.
3. Problem on steering gear mechanism.

List of Drawing Sheets:

1. Graphical solution to problems on velocity acceleration in mechanism by relative velocity and
acceleration method including problem with Corioli’s component of acceleration.
2. Velocity by instantaneous center method.
3. Klein’s construction and inertia force analysis for slider cranks mechanisms.
4. To draw cam profile for various types of followers motion.

(ME 16013) Fluid Mechanics Laboratory

Teaching Scheme: Examination Scheme:

Lectures : 2hrs / week Term Work: 50 marks
Oral: 50 marks

Course Outcomes:
Student will be able to
1. Do the pressure measurement using manometers
2. Calculate viscosity of a fluid.
3. Determine the forces experienced by the body when flow occurs around it
4. Carry out the velocity measurement using pitot tube
5. Determine the coefficient of discharge using Bernoulli’s equation
6. Determine the friction factor for flow

List of Experiments:
1. Measurement of viscosity using Red Wood viscometer
2. Study and demonstration of pressure measurement using manometers
3. Determination of the metacentric height of a floating body and its stability
4. Demonstration of electrical analogy method for flow measurement
5. Determination of coefficient of discharge for Venturi meter
6. Determination of coefficient of discharge for orifice meter
7. Determination of coefficient of discharge for rectangular notch
8. Demonstration of Pitot tube for velocity measurement

58
 9. Determination of the friction factor for flow through a long circular pipe
10. Determination of pressure variation around a circular body when it is submerged in a flow

(ME 16014) Fundamentals of Metallurgy Laboratory

Teaching Scheme: Examination Scheme:
Lectures : 2hrs / week Term Work: 50 marks
Oral: 50 marks

Course Outcomes:
Students will be able to
1. Perform mechanical tests on metallic materials.
2. Perform heat treatment on steels.
3. Distinguish between microstructures of various metallic materials.

List of Experiments:
1. To perform hardness test on different metallic samples.
2. To perform tensile test on different metallic samples.
3. To perform Impact test on different metallic samples.
4. Non-Destructive tests: Magnaflux testing, Dye penetrant testing.
5. Study and drawing of microstructures of various types’ plain carbon steel.
6. To perform various types of heat treatment on plain carbon steels.
7. To study effect of heat treatment on microstructure and hardness of plain carbon steel.
8. Study and drawing of microstructures of various types cast irons.

(ME 16015) Manufacturing Engineering- II Laboratory

Teaching Scheme: Examination Scheme:

Lectures : 2hrs / week Term Work: 50 marks
Practical Exam with oral: 50 marks

Course Outcomes:
At the end of the course, students should be able to:
1. Use different Non-Conventional processes for the given applications.
2. Perform job on CNC machine by using CNC programming.
3. Use manufacturing machine tools and make the given jobs.
4. Design the Jigs and Fixture for the given jobs.

Termwork:

Each candidate shall be required to complete and submit the following term work.

59
Part A
1. One composite job consisting of at least one spur gear to be made by each student.
2. One composite Job on CNC Lathe/Milling which includes operations like Turning, Facing, Taper
Turning, Drilling etc.

Part B
1. Demonstration on different non-conventional machining set-ups to manufacture simple
components.
2. Demonstrations on different surface treatment processes.

Part C
A journal consisting of:
1. Design of a jig or fixture. (No fabrication).
2. A report of visit to any surface treatment industry.
3. Assignments on NC/CNC Machines, Press working, Non conventional processes, Advanced
manufacturing Processes etc.

Semester IV (For Direct Second Year Admitted Diploma Students)

(MA ) Multivariate Calculus and Differential Equations

Teaching Scheme: Examination Scheme:

Lectures : 4hrs / week T1 and T2: 20 Marks each
Tutorial: 1Hr/week End Sem. Exam: 60 marks

Course Outcomes:

Students will be able to:

1. Know and recall core knowledge of the syllabus. (To measure this outcome, questions may be of
the type- define, identify, state, match, list, name etc.)
2. Understand basic concepts. (To measure this outcome, questions may be of the type- explain,
describe, illustrate, evaluate, give examples, compute etc.)
3. Analyze the problem and apply the appropriate concept. (To measure this outcome, questions
will be based on applications of core concepts)
4. Give reasoning. (To measure this outcome, questions may be of the type- true/false with
justification, theoretical fill in the blanks, theoretical problems, prove implications or corollaries
of theorems, etc.)
5. Apply core concepts to new situations. (To measure this outcome, some questions will be based
on self-study topics and also comprehension of unseen passages.)

Unit I: Functions of several variables, level curves and level surfaces, partial and directional derivatives,
differentiability, chain rule, local extreme values and saddle points. [06 Hrs]

60
Unit II: Double integrals in Cartesian and polar co-ordinates, iterated integrals, change of variables,
triple integrals in Cartesian, spherical and cylindrical co-ordinates. [11 Hrs]

Unit III: Vector differentiation, gradient, divergence and curl, line and surface integrals, path
independence, statements and illustrations of theorems of Green, Stokes and Gauss. [10 Hrs]

Unit IV: Review of first order differential equations, linear differential equations, homogeneous higher
order linear differential equations, non-homogeneous higher order linear differential equations with
constant coefficients (method of undetermined coefficients and method of variation of parameters).
[09 Hrs]

Unit V: Laplace Transforms, its properties, Unit step function, Dirac delta functions, Convolution
Theorem, periodic functions, solving differential equations using Laplace transform. [07 Hrs]

Unit VI: Partial differential equations with separation of variables, boundary value problems: vibrations
of a string, one dimensional heat equation. [07 Hrs]

Text Books:
 Maurice D. Weir, Joel Hass, Frank R. Giordano, "Thomas’ Calculus", Pearson Education, 12th
Edition.
 Erwin Kreyszig, "Advanced Engineering Mathematics", Wiley eastern Ltd., 10th Edition.

Reference Books:
 K.D. Joshi, “Calculus for Scientists and Engineers”, CRC Press.
 Sudhir Ghorpade and Balmohan Limaye, “A Course in Multivariate Calculus and Analysis”,
Springer Science and Business Media.
 George Simmons, “Differential Equations with Applications and Historical notes”, Tata Mc-Graw
Hill publishing company Ltd, New Delhi.
 Wendell Fleming, “Functions of several variables”, Springer-Verlag, New York.
 Fritz John, “”Partial Differential Equations (4th edition), Springer.
 C.R. Wylie, “Advanced Engineering Mathematics” , McGraw Hill Publications, New Delhi.
 Peter V. O’ Neil, “Advanced Engineering Mathematics”, Thomson Brooks / Cole, Singapore, 7 th
edition.
 Michael D. Greenberg, “Advanced Engineering Mathematics (2nd edition)”, Pearson Education.

*****

61