Scribd Logo
Upload

Welcome to Scribd!

  • 177 views

    QuickServe en Línea - (4310736) ISX15 CM2250 SN Manual de Servicio

    Uploaded by

    hamilton miranda
    The document provides instructions for servicing fuel filters on a vehicle. It describes removing the old filter, installing the new one, and priming the fuel system after. Safety warnings are provided throughout regarding working with fuel, batteries and compressed air.

    Copyright:

    © All Rights Reserved
    Download as PDF, TXT or read online from Scribd

    QuickServe en Línea - (4310736) ISX15 CM2250 SN Manual de Servicio

    Uploaded by

    hamilton miranda
    177 views5 pages
    The document provides instructions for servicing fuel filters on a vehicle. It describes removing the old filter, installing the new one, and priming the fuel system after. Safety warnings are provided throughout regarding working with fuel, batteries and compressed air.

    Original Title

    QuickServe en línea _ (4310736) ISX15 CM2250 SN Manual de servicio (17)

    Copyright

    © © All Rights Reserved

    Available Formats

    PDF, TXT or read online from Scribd

    Did you find this document useful?

    Is this content inappropriate?

    The document provides instructions for servicing fuel filters on a vehicle. It describes removing the old filter, installing the new one, and priming the fuel system after. Safety warnings are provided throughout regarding working with fuel, batteries and compressed air.

    Copyright:

    © All Rights Reserved
    Download as PDF, TXT or read online from Scribd
    Download as pdf or txt
    177 views5 pages

    QuickServe en Línea - (4310736) ISX15 CM2250 SN Manual de Servicio

    Uploaded by

    hamilton miranda
    The document provides instructions for servicing fuel filters on a vehicle. It describes removing the old filter, installing the new one, and priming the fuel system after. Safety warnings are provided throughout regarding working with fuel, batteries and compressed air.

    Copyright:

    © All Rights Reserved
    Download as PDF, TXT or read online from Scribd
    Download as pdf or txt
    You are on page 1of 5

    (/qs3/pubsys2/xml/en/manual/4310736/4310736-titlepage.

    html)

    Información general
    El sistema de combustible requiere el uso de dos filtros de
    combustible. El filtro del lado de succión debe tener las
    siguientes características:
    Separador de agua
    Calificación de 10 micras
    Sensor de agua en combustible con resistencia de
    derivación
    Válvula de drenaje de agua
    Motor o chasis montado.

    El filtro del lado de presión debe tener las siguientes


    características:
    Calificación de 5 micras
    Motor montado.
    Utilice el siguiente procedimiento en el Manual de operación y
    mantenimiento, ISX15 CM2250 SN, Boletín 4310735, para
    obtener recomendaciones sobre el filtro de combustible.
    Consulte el Procedimiento 018-024 en la Sección V.
    (/qs3/pubsys2/xml/en/procedures/175/175-018-024-om.html)

    El sistema también contiene un filtro de combustible ubicado


    en el perno banjo en la entrada de la bomba de combustible de
    alta presión:
    Clasificación de 86 micras
    Located inside the banjo bolt
    Serviced by replacing the banjo bolt.
    Preparatory Steps
     WARNING 
    When using a steam cleaner, wear safety glasses or a face
    shield, as well as protective clothing. Hot steam can cause
    serious personal injury.

     WARNING 
    Wear appropriate eye and face protection when using
    compressed air. Flying debris and dirt can cause personal
    injury.

     CAUTION 
    Clean all fittings before disassembly. Dirt or contaminants
    can damage the fuel system.

    Before servicing any fuel system components, (such as fuel


    lines, fuel pump, injectors, etc.), which would expose the fuel
    system or internal engine components to potential
    contaminants prior to disassembly, clean the fittings, mounting
    hardware, and the area around the component to be removed.
    Dirt or contaminants can be introduced into the fuel system
    and engine if the surrounding areas are not cleaned, resulting
    in damage to the fuel system and engine. Refer to Procedure
    000-009 in Section 0.
    (/qs3/pubsys2/xml/en/procedures/175/175-000-009-tr.html)
    Clean the fuel filter head with contact cleaner, Part Number
    3824510 or equivalent.

    Clean the fuel filter head or remote mount fuel filter head with
    contact cleaner, Part Number 3824510 or equivalent.
    To prevent damage from debris and contamination, cover, cap,
    or plug any openings as soon as possible when servicing the
    fuel system.  Caps and plugs can be found in Clean Care Kit,
    Part Number 4919073.

     WARNING 
    Batteries can emit explosive gases. To reduce the possibility
    of personal injury, always ventilate the compartment before
    servicing the batteries. To reduce the possibility of arcing,
    remove the negative (-) battery cable first and attach the
    negative (-) battery cable last.

    Disconnect the batteries. See equipment manufacturer


    service information.

    Remove
     WARNING 
    Depending on the circumstance, diesel fuel is flammable.
    When inspecting or performing service or repairs on the fuel
    system, to reduce the possibility of fire and resulting severe
    personal injury, death, or property damage, never smoke or
    allow sparks or flames (such as pilot lights, electrical
    switches, or welding equipment) in the work area.

    Remove the fuel filter with filter wrench, Part Number 3400157.
    Make sure the seal ring does not stick to the filter head.

    Remove the ring with an o-ring pick, if necessary.

    Install
    Use the correct filter(s) for the engine. Filters must remove a
    minimum of 98.7 percent of free and emulsified water. They
    must also have a 5-micron particle removal efficiency.

    Use the following procedure in the Operation and Maintenance


    Manual, ISX15 CM2250 SN, Bulletin 4310735, for fuel filter
    recommendations. Refer to Procedure 018-024 in Section V.
    (/qs3/pubsys2/xml/en/procedures/175/175-018-024-om.html)
    Apply a thin coating of clean engine oil to the filter gasket
    surface.
    Note : Cummins® Fleetguard® filters come equipped
    with a disposable insert that will prevent fuel from
    entering the clean side of the filter media during
    prefilling.
    Note : If the engine is not equipped with a lift pump, the
    fuel filter will have to be properly pre-filled before
    installation. Refer to Procedure 005-234 in Section 5.
    (/qs3/pubsys2/xml/en/procedures/175/175-005-234-
    tr.html)

     CAUTION 
    Mechanical overtightening of the filter can distort the threads
    or damage the filter element seal.

    Note : Engines equipped with priming pumps do not


    require the fuel filter to be filled prior to installation, if
    the following filling procedure is followed.
    Install the filter onto the filter head. Turn the filter until the
    gasket contacts the filter head surface.
    Apriete el filtro una additional de vuelta adicional después de
    que la junta entre en contacto con la superficie del cabezal del
    filtro, o según lo especificado por el fabricante del filtro.

    Cebe el sistema de combustible. Consulte el Procedimiento


    005-234 en la Sección 5.
    (/qs3/pubsys2/xml/en/procedures/175/175-005-234-tr.html)

    Pasos finales
     ADVERTENCIA 
    Las baterías pueden emitir gases explosivos. Para reducir la
    posibilidad de lesiones personales, ventile siempre el
    compartimento antes de reparar las baterías. Para reducir la
    posibilidad de arco eléctrico, retire primero el cable negativo
    (-) de la batería y luego conecte el cable negativo (-) de la
    batería.

    Conecta las baterías. Consulte la información de servicio


    del fabricante del equipo.
    Opere el motor y verifique si hay fugas.

    Última modificación: 17-feb-2015

    You might also like