PAVISINT SEALER 45 - en

SPORTS SURFACES
PAVISINT SEALER 45
DATA SHEET
Two-component polyurethane paste

for smoothing and sealing prefabricated granular rubber and/or cast in situ decks
CHARACTERISTICS
Product for laying gym flooring, that may be applied on prefabricated granular rubber decks and/or cast on site, to lay sports surfaces with Pavisint
SL 75 systems.
Pavisint Sealer 45 is an intermediate layer laid between a granular rubber deck and the next self-levelling layer, that is used to smooth and seal the
surface of the granular rubber deck or cast-in-situ.
APPEARANCE
Component A: pigmented viscous paste.

Component B: dark medium-viscosity liquid.
CHARACTERISTICS OF THE LIQUID PRODUCT
Characteristic U.M. Value Tolerance
Specific weight Kg/dm³ 1,29 ± 0,1
Dry mass residue % 99,7 ± 0,5
Dry volume residue % 99,5 ± 0,5
Residue at 450°C % 35 ± 0,5
Brookfield viscosity (with Brookfield viscosimeter rotor no. 6, speed 20) mPa·s 38000 ± 3500
Mixing ratio (A:B) by weight - A:B = 82:18 -
LAYING INSTRUCTIONS
Tools Thinner Type of thinner Cleaning tools
Smooth squeegee Ready to use - DIL S1
LAYING SURFACE
Granular rubber deck made with prefabricated SPORMAT, prefabricated rubber tiles or granular rubber cast-in-situ. In all cases, the bottom should
be perfectly flat and compact.
IMPORTANT: resin surfaces are generally waterproof (non draining) surfaces, so that decks should be sloped correctly to ensure efficient rainwater
run-off and prevent pooling. Any corrections that may be required should be made before laying the final coating; if necessary, please consult the
Technical Office of Casali S.p.A.
CONSUMPTION
Depending on the type of deck, the minimum recommended coverage is as follows:

- 0.5 Kg/sq.m in two coatings (a first 300 g./sq.m. coating followed by a second 200 g./sq.m. coating) on prefabricated Spormat surface;
- 1.5 - 1.7 Kg/sq.m. on rubber decks cast in situ. Use test samples to get a true idea of the amount of product required.
p.1
Rev. 02/2018
CASALI S.p.A. - synthetic division - z.i. C.I.A.F. Castelferretti (AN) ITALY tel. +39 0719162095 fax +39 0719162098 www.casaligroup.it [email protected]
SPORTS SURFACES
PAVISINT SEALER 45
DATA SHEET
APPLICATION INSTRUCTIONS
Ambient temperature: MIN 10°C - MAX 40°C

Ambient relative humidity: MAX 80 %
Laying surface temperature: MIN 10°C - MAX 35°C
HARDENING AT 23°C AND R.H. OF 50%
Pot life 30’
Interval between coatings MIN 20 h - MAX 36 h
Maximum hardening time 5 days
The times indicated refer to standard laboratory conditions. Drying times are strongly influenced by the weather; high temperatures and direct sun-
light accelerate drying; shadows, low temperatures and high humidity levels delay drying. In winter, lay the product in the central and warmer hours
of the day. Always ensure that the previous layer has hardened correctly before applying the next layer.
PACKAGING INSTRUCTIONS
Colours available Grey
Packaging A + B = 20 kg
STORAGE INSTRUCTIONS
Storage temperature: MIN 10°C - MAX 40°C
Stability in the original package: 6 months
CERTIFICATION
PAVISINT SEALER 45 TOGETHER WITH THE PAVISINT SL 75 SYSTEM AS A WHOLE IS CERTIFIED ACCORDING TO ITALIAN FIRE RESISTANCE
LAWS IN CLASS 1 AND ACCORDING TO EUROPEAN LAWS IN CLASS B fl - s1
IMPORTANT INSTRUCTIONS
Do not apply the product in foggy or damp weather, or if rain or frost are forecast. Ensure that the deck is perfectly flat and sturdy with the correct
aggregate grading to prevent flaws on the surface. Repairs and/or filling should be carried out in accordance with the instructions of Casali S.p.A.
Check for rising damp and/or infiltrations, and if necessary contact the Technical Office of Casali S.p.A. office for more information.
Store component B at a temperature between 10°C and 30°C, otherwise the material may crystallize and be unsuitable for use. The material may
however be reconditioned for several hours with a heater or water bath at 40-45 °C, shaking the tin to eliminate lumps, and bringing the material back
to a liquid state (the hardener must be limpid otherwise the crystals are not perfectly blended). The heated material must be applied immediately oth-
erwise it will deteriorate and can no longer be used
SAFETY STANDARDS
Please read the safety data sheet before using the product.
The data provided by these data sheets are approximate and the Company reserves the right to modify the same for technical reasons, without prior notice. The solutions
proposed do not represent all the possible uses but are merely case studies deriving from Casali’s installation experience and are therefore intended only for purposes of
illustration. The user is exclusively responsible for the way the products illustrated are used, whether properly or improperly, for evaluating in advance the suitability or oth-
erwise of the product for its requirements and exerting the utmost caution in handling chemical products. Important: to ensure best colour uniformity of surface laid
products, we recommend that you use materials from the same production lot as finishing layer. The Technical Office of Casali’s Synthetics Division is at your
complete disposal for any further specific information or explanations you may require (phone 071 9162095).
p.2
Rev. 02/2018
CASALI S.p.A. - synthetic division - z.i. C.I.A.F. Castelferretti (AN) ITALY tel. +39 0719162095 fax +39 0719162098 www.casaligroup.it [email protected]

PAVISINT SEALER 45 - en

Uploaded by

Copyright:

Available Formats

PAVISINT SEALER 45 - en

Uploaded by

Document Information

Original Title

Copyright

Available Formats

Share this document

Share or Embed Document

Sharing Options

Did you find this document useful?

Is this content inappropriate?

Copyright:

Available Formats

PAVISINT SEALER 45 - en

Uploaded by

Copyright:

Available Formats

SPORTS SURFACES

Two-component polyurethane paste

Component A: pigmented viscous paste.

CHARACTERISTICS OF THE LIQUID PRODUCT

Characteristic U.M. Value Tolerance

Specific weight Kg/dm³ 1,29 ± 0,1

Dry mass residue % 99,7 ± 0,5

Dry volume residue % 99,5 ± 0,5

Residue at 450°C % 35 ± 0,5

Mixing ratio (A:B) by weight - A:B = 82:18 -

Tools Thinner Type of thinner Cleaning tools

Smooth squeegee Ready to use - DIL S1

Depending on the type of deck, the minimum recommended coverage is as follows:

Ambient temperature: MIN 10°C - MAX 40°C

HARDENING AT 23°C AND R.H. OF 50%

Pot life 30’

Interval between coatings MIN 20 h - MAX 36 h

Maximum hardening time 5 days

Colours available Grey

Storage temperature: MIN 10°C - MAX 40°C

Stability in the original package: 6 months

You might also like