FEATURES AND PROGRAMMING GUIDE

DOOR♦GARD TM COMMAND AND CONTROL SERIES

DOOR♦GARD COMMAND AND CONTROL SERIES keypads offer field proven reliability and cost effective
solutions anywhere limited control or access is desired. Designed for individual control of up to four devices, Door♦Gard
Command and Control Series keypads are the perfect choice for controlling electric locking devices, security systems,
automatic operators or machinery. Door♦Gard keypads accept power from a 12 or 24 Volt AC/DC supply.

FEATURES:
• 4 INDEPENENT OUTPUTS REMOTE TRIGGERING INPUT (REX)
• 4 INDEPENENT TIMERS By default, upon a momentary closure this normally
• ALL OUTPUTS ASSIGNABLE BY CODE open loop triggers the main relay for the same time
• ON BOARD MAIN RELAY period as the Master Code. You can also program the
• 120 USERS REX to operate any combination of the available
• REMOTE TRIGGERING INPUT outputs. The auxiliary outputs activate for their
• KEYPAD PROGRAMMABLE programmed time.

MEMORY KEYPRESS FEEDBACK/AUDIBLE KEYPRESS

Non-volatile EEPROM memory means your codes and Door♦Gard Command and Control keypads, by default,
instructions will be there whether you remove power for acknowledge a keypress by momentarily illuminating the
5 minutes or 5 years. yellow LED or activate the sounder. This depends on
the model. You can turn this off through programming.
PROGRAMMING
All programming is done entirely from the front of the KEYPAD ACTIVE OUTPUT
keypad. LED or sounder guidance makes programming Door♦Gard Command and Control keypads can be
easy. It takes seconds for an authorized user to change programmed to energize a voltage output whenever a
codes. key is touched. You can use this to turn on lights, CCTV
camera, or notify a guard. This output is not available if
CODES you are using the IEI 250 Printer Interface.
The Door♦Gard Command and Control keypads allow
up to 120 individual user codes. Codes can be 1 to 6 AUTO ENTRY
digits in length and digits may be repeated. The Master This feature is used when you don’t want to press the *
Code is always stored in user location one (1). key after entering your code. You only need to enter
your code number (without pressing *) and the relay
MAIN RELAY activates. To use this feature, the user codes must be
The main relay is a form C relay, which you can program the same length as the master code. Please remember
as a timed output (1 to 90 seconds) or to toggle (latch). to access program mode when auto entry is on, do not
See the Wiring Diagram and Specifications for the relay press the * key (Press: 99 # master code), however the *
electrical specifications. is required while entering programming commands.

AUXILIARY OUTPUTS AUDIT TRAIL

You can program these outputs as timed outputs (1 to Using the 250 Printer Interface (not included), you can
90 seconds) or to toggle (latch). They can be controlled get an accurate real-time audit trail. Up to 8 keypads can
individually or in combination by a code. Some models be monitored simultaneously. The 250 comes with a
have 1 Amp form C relays and other models have power supply and a printer cable and it easily connects
negative voltage outputs with a 50mA sink.* to any parallel printer. This output is not available on all
models.
PANIC
Panic is activated by pressing the * and # keys at the *Voltage Outputs may be converted to 1 Amp, Form-
same time. By default, it operates output 4 and activates C relays by adding the 293 Auxiliary Relay Board
for 1 second. (Model # 0219000).

6050212 Rev. 1.1 1 www.ieib.com

1 2
TESTING THE KEYPAD PROGRAMMING
1. Connect the positive (+) lead of your power supply to
the terminal strip (TS1) V+ input. 1. Enter programming mode Yellow LED
Press 99 # (master code) * Flashes slowly
2. Connect the negative (-) lead of your power supply to
the terminal strip (TS1) V- input. 2. To Change master code1
Press 1 # (new master code) * Flashes fast
3. Turn on your power supply. Press (new master code) * Flashes slowly
If you must change the Main Relay
4. Press 7890#123456 *. If all 12 keypresses are time, see option 2 on the
verified, the keypad enters self-test mode. Programming Options chart.
The yellow LED flashes 3 times, then turns on solid
for 3 seconds 3. To Add/change second code
Press 2 # (new user code) * Flashes fast
Note: Self-test mode can be used to troubleshoot a Press (new user code) * Flashes slowly
keypad in the field. If you do not get the continuous
light, the memory has been corrupted and should be 4. To Add/change third code
re-programmed with the default command (see Press 3 # (new user code) * Flashes fast
option #19). Press (new user code) * Flashes slowly

5. Enter the master code (default = 1234) followed by 5. Up to 120 codes may be added
the * key and the relay energizes. Refer to in this fashion
programming section to program your keypad.
6. Exit programming mode
NOTE: Press * Off
You can program your keypad in your shop or at the
NOTES:
installation site. Programmed information is stored in
non-volatile memory so it won’t be lost if power is
removed. • Door♦Gard Command and Control keypads are factory
programmed with a master code of 1234.

• 1
The master code is always stored in user location
COMMAND AND CONTROL 1.
DEFAULTS
• The master code allows access to programming mode
Door♦Gard Command and Control keypads are
and activates the main relay.
designed for easy installation in a minimum amount of
time. The following default settings are factory
programmed: • By default (auto-entry is off), all codes must be followed
by the * key.
Master Code (user 1): 1234
Main Relay Time: 5 seconds • Codes may be from 1-6 digits in length, and digits
Auxiliary Output Time: 5 seconds may be repeated.
Panic Output: Output 4
Keypad Active Output: Off • If you forgot the master code or it is not working,
REX Triggers: Main Relay momentarily push SW1, (see wiring diagram for
Keypress Feedback: On location) to enter programming mode and go to option
LED – Normal State Red #19 on the Programming Options chart to default
LED - Relay Energized Green keypad.
Auto-Entry Off
• If the yellow LED lights solid while in programming
If you must change the default settings or additional mode, an error has occurred. Press * to clear (yellow
functions are desired, please refer to the Programming LED should start flashing) and start over from step 2 or
Options Chart after you are familiar with the 3 above.
Programming section.

6050212 Rev. 1.1 2 www.ieib.com

3
PROGRAMMING OPTIONS CHART
If the pre-programmed default values must be changed or additional functions are desired, the following options may
be programmed.

1. Enter programming mode Press 99 # (master code) *

2. Change master code/set main relay time1 Press (time) # 1 # (new code) * (new code) *
Example: Master code of 4321/relay time of 10 seconds Press 10 # 1 # 4321 * 4321 *

3. Add/change user code Press (user number) # (new code) * (new code) *

4. Add/change user code to toggle main relay1 Press (00) # (user number) # (new code) * (new code) *

5. Delete user codes Press (user number) # * *

6. Set output 2 time1 Press 12 # (Relay Time) # 0 # **

7. Set output 3 time1 Press 13 # (Relay Time) # 0 # **

8. Set output 4 time1 Press 14 # (Relay Time) # 0 # **

9. Set outputs for Remote Triggering Input Press 17 # (outputs: 1, 2, 3 and/or 4) # 0 # **

10. Set outputs for Panic Press 18 # (outputs: 1, 2, 3 and/or 4) # 0 # **

11. Turn keypress feedback/audible keypress on Press 30 # 0 # 1 # * *

12. Turn keypress feedback/audible keypress off Press 30 # 0 # 0 # * *

13. Turn yellow LED/sounder on with relay Press 30 # 1 # 1 # * *

14. Turn yellow LED/sounder off with relay Press 30 # 1 # 0 # * *

15. Turn auto entry on Press 30 # 2 # 1 # * *

16. Turn auto entry off Press 30 # 2 # 0 # * *

17. Turn keypad active on2 Press 43 # 0 # 99 # * *

18. Turn keypad active off Press 43 # 0 # 00 # * *

19. Erase keypad memory/reset defaults Press 46 # 00000 # 00000 # * *

20. Energize selected output(s) with a user code3 Press 59 # (outputs 1, 2, 3 and/or 4) # user location # (new
code) * (new code) *
Example: User 2; code 4321; energize outputs 2 & 3 Press 59 # 23 # 02 # 4321 * 4321*
21. Exit programming mode Press *

NOTES:

1. Relay times must always be represented by 2 digits. Example: 5 seconds = 05. Latching /toggle is accomplished by
entering a time of 00.

2. Keypad active is a negative voltage output (sink) available on terminal (or wire) marked WB (see wiring diagrams for
location).

3. This feature does not work with the master code.

6050212 Rev. 1.1 3 www.ieib.com

COMMAND AND CONTROL STYLES

212i INDOOR STYLE • Small design suitable for residential, commercial and
• Flushmount, indoor design industrial applications
212w WEATHER RESISTANT STYLE • 4 On-Board Relays
• Flushmount, outdoor design 212iLM MULLION STYLE
212r RUGGEDIZED STYLE • Weather resistant metal housing
• Weatherproof self-contained metal housing • Narrow housing suitable for aluminum door frame
• Vandal resistant mounting
• Cast metal housing suitable for wall, post or gooseneck • Available in Bronze or Satin Aluminum
mounting 212mp MULTIPAD BACKLIT STYLE
• Available in white or black • Weatherproof self-contained housing.
• 4 On-Board relays • Illuminated Keys
212se SEALED ENVIRONMENTAL STYLE • Contemporary Design
• Weatherproof self-contained metal housing • 4 On-board Relays
• Vandal resistant
ACCESSORIES

DATA LOGGING TAMPER PROTECTION

• IEI-250 PRINTER INTERFACE provides power, • IEI-282 TAMPER SWITCH detects faceplate removal
communication inputs and outputs for up to 8 Door♦Gard • IEI-283 SECURITY MODULE responds to tamper switch
keypads. Interfaces with any parallel printer for user/door (included) and cuts all in/out power to the door lock. Wires
activity logging can’t be crossed to unlock door. Must be reset from inside
INSTALLATION the protected area.
• IEI-280 WEATHERPROOF SURFACE BACK BOX • IEI-289 TAMPER SCREWS - TRI-HEAD
• IEI-281 FLUSH MOUNT BACK BOX • IEI-267 1/4” DRIVER
• IEI 12 or 24 VDC 1A PLUG-IN POWER SUPPLIES • IEI-270 ADAPTER SOCKET - TRI-HEAD
• IEI-293 THREE RELAY PLUG--IN BOARD with FORM C, • IEI-271 TAMPER WRENCH - ALLEN WITH PIN
1 Amp relays. Converts transistor outputs to dry contacts • IEI-288 TAMPER SCREWS - ALLEN WITH PIN
(for use with Command and Control indoor, weather
resistant and Mullion styles).

OTHER DOOR♦GARD PRODUCTS FROM IEI

CONTROL PANEL ACCESS CONTROL SYSTEMS POWERGARD POWER SUPPLIES

210 Programmable Keypad-Direct hardwire PG1224-1 12/24VDC 1.3 Amp Power Supply
keyswitch replacement PG1224-3 12/24VDC 2.5 Amp Power Supply
240 Battery Operated Keypad-Direct
keyswitch replacement (for indoor use)
262 The Partitioner Self-Contained 2-zone control

SELF-CONTAINED ACCESS CONTROL SYSTEMS FEATURES

232i Indoor Keypad • Lock Release Relay • Propped Door Alarm Relay
232w Weather-Resistant Keypad • Lock Release Time • Timed Egress Input
232se Sealed Environment Keypad • Alarm Zone Shunting Relay • Forced Door Alarm Relay
232r Ruggedized Keypad • Multiple User • Front Programmable
232iLM Mullion Keypad
233 Card Reader System
234 Card Reader/Keypad System
If this product does not seem to operate properly, please call our Technical Support Department toll free at 1-800-343-9502 (or 781-821-5566)
Monday-Friday 8:00 A.M. – 7:00 P.M. EST. We understand your time is valuable and we know that calling our Technical Support Department will
ensure that you’ll make the most profit possible with your IEI product. Thank you for your purchase. We appreciate your business.
International Electronics, Inc. (IEI) warrents its products to be free from defects in material and workmanship when they have been installed in
accordance with the manufacturer’s instructions and have not been modified or tampered with. IEI does not assume any responsibility for damage or
injury to person or property due to improper care, storage, handling, abuse, misuse, normal wear and tear or an act of God.
IEI’s sole responsibility is limited to the repair (at IEI’s option), the replacement of the defective product or part when sent to IEI’s facility (freight and
insurance charges prepaid), after obtaining IEI’s Return Merchandise Authorization. IEI will not be liable to the purchaser or any one else for incidental
or consequential damages arising from any defect in, or malfunction of, it’s products.
This warranty shall expire two years after shipping date. Except as stated above, IEI makes nor warranties, either expressed or implied, as to any
matter whatsoever, including, without limitation to, the condition of its products, their merchantability, or fitness for any particular reason.

International Electronics, Inc.

427 Turnpike St, Canton, MA 02021 U.S.A.
800-343-9502, 781-821-5566, 781-821-4443 (FAX)
Fax Information Center 781-821-0734 (From Your FAX machine)

6050212 Rev. 1.1 4 www.ieib.com