UNLOCK HUAWEI E153

 
Proceed with caution, and  use the tutorial at your own risk! And again, follow
the tutorial as described! If its not described, don’t do it!.  So please read it first
before performing it.
 
Step 1. Backup the device’s data (NVItems). Download the QPST software.
Install this software; you will need it on the succeeding steps.
You will need the backup file in case something went wrong
Step 2. Locate your device’s port. Go to Control Panel, Device Manager. Click
“Ports”.
 
 
Step 3. Run the QPST software from your Windows programs menu. Click
Start, All programs, QPST, Select “QPST Configuration”
 
 
Step 4. Add the port located from Step 2, to the running QPST program
then choose your com port it suppose be Application com port
 
 
Step 5. Uncheck “Show Serial and USB/QC Diagnostic Port Only” to reveal all
COM Ports. Highlight the device’s port.
 
 
If you done it correct, you will see something like
It starts with SURF6246 in Philippines
 
 
Step 6. Highlight the COM Port from Step 5, click “Start Clients”, and select
“Software Download”
 
 
Step 7. Click the “Backup” tab. Before commencing, make sure the Port:
portion of the menu is pointing to the correct COM port. On the QCN File:,
just click the browse button, and select the directory/folder you want the
NVItems data to be saved. Click “Start”
 
 
Step 8. Download Huawei Flasher, and the Huawei E153 Downgrade firmware.
Step 9. Start the Huawei Flasher Program. Connect your Huawei E153 dongle,
and close the 3G modem dashboard (the modem application to connect to
internet) if it’s open. Wait until your modem is detected in the Huawei Flasher
program.
 
 
Step 10. Click “Select Firmware” and point it to the E153 Downgrade Firmware
file from Step 8. You should see “6246_K” on the Model: portion of the menu
Make sure the MODEL box will show 6246_K if its not like that then stop at this
point to prevent bricking your modem
 
 
Step 11. Uncheck the “06.bin” on the menu. It is needed so that you won’t get
error message when downgrading the modem. Click “Flash modem”, and
select “Normal mode”. Wait for the pop-up box for 10 seconds before clicking
OK. Then leave the software and modem for the downgrading process. At the
end of the process, you will get an error (on the 08.bin) but it’s normal. Wait
until it is fully finished
Count 10 seconds before clicking OK! Don’t unplug the modem or use any
program while doing this operation!
 
 
Now, you can use any SIM you like on your unlocked Huawei E153 3G
modem!
If you want to restore…
For restore procedure, perform Step 1 up to Step 6, but on Step 7 select the
“RESTORE” tab instead
 
  
Then you are Done and your modem is unlocked. 
 
 
 
 
 
 
1. FLASHING HUAWEI E303 Hi Link
Hi Link modems  ukishaiplug in tu inaconnect internet unless umeiset
kuiconnect manually. Hazitumii normal Huawei dashboard zinatumia their
own “Web UI” hivyo haziwezi kuwa detected kwenye normal dashboard za
Huawei. Na hata ukiiconnect kwenye PC, jamaa wanakuwa wamedisable
PORT na hutaweza kuiona ktk device manager under Ports, Modems or
Network adapter, so ukisema uiunlock kwa kutumia Flashing method kama za
E303 za kawaida hautafanikiwa.
 
 
 
 
NJIA YENYEWE
Vodacom Huawei E303 Hi link modem ni customized Firmware so njia pekee
ya kuiunlock ni kwa ku flash.
 
REQUIREMENTS
Maelezo ninayotoa ni kwa ajili ya PC tu, na vitu vinavyoihitajika ni
 Huawei Mobile Partner (Version ya hivi karibuni)  Lazima iwe installed
kama hauna download HAPA
 Huawei E303 Hi Link Firmware nenda HAPA kudownload
 Important softwares (Terminal na Universal MasterCode) nenda HAPA
kudownload
Note:
Password kwa link zote ni ‘gkiwango’ bila quotes.
 
KUFANYA MODEM IWEZE KUONYESHA PORTS
Ili kuweza kuiflash modem, inabidi kuifanyia trick ili modem iweze kuonesha
ports ambazo inatumia katika pc. Unachotakiwa kufanya tembelea hii link
http://192.168.1.1/html/switchProjectMode.html , Utakopovisit hiyo link
modem ita disconnect na kuconnect tena, na PORTS zitakuwa ENABLED.
Sasa PC ita detect two unknown devices (Huawei HiLink x2) maana windows
inakuwa haifahamu driver za kutumia kwa hizo devices.
windows inakuwa haifahamu driver za kutumia kwa hizo devices.
Hizo device mbili zitakuwa na hardware ID hizi
 
USB\Vid_12d1&Pid_1442&MI_00
USB\Vid_12d1&Pid_1442&MI_01
Hizo drivers zinapatikana kwenye Mobile Partner, sema zinatakiwa kufanyiwa
modification kidogo ili ziweze kufanya kazi na Huawei HiLink.
Hii proces inafanywa mara moja, otherwise kama uta unistall Mobile Partner
ndo itakubidi urudie tena.
Nenda kwenye Mobile Partner na u-locate hili file “ewser2k.inf”, linapatikana
kwenye
 
C:\Program Files\Mobile Partner\Driver\Driver\X86 kwa 32 Bit au
C:\Program Files (x86)\Mobile Partner\Driver\Driver\X64 kwa 64 Bit
 
Scroll mpaka kwenye [QcomSerialPort...] na uongeze hizi lines
 
%QcomDevice01% = QportInstall01, USB\VID_12d1&PID_1442&MI_00
%QcomDevice00% = QportInstall00, USB\VID_12d1&PID_1442&MI_01
 
Hii ni kufanya windows iweze kujua driver zipi za kutumia kwenye zile device
zetu. Na sehemu nzuri ya kuweka hizo lines ni katikati ya PID_143E &
PID_1448, na itakuwa kama hivi
 
Baada ya hapo sasa rudi kwenye Device Manager na kwa kila device fanya ku-
update driver zake, na ubrowse kwenye location ya “ewser2k.inf”. Baada ya
 hapo device zetu zitaonekana na ports zao ie, 3G PC UI Interface & 3G
Application Interface ila hutaweza ku connect na internet.
 
KUFANYA HiLink MODEM I DIAL KAMA MODEM ZA KAWAIDA
Fungua “Terminal” na ufungue port ya 3G PC UI Interface na send hizi AT
Commands kwenda kwenye modem……
AT^U2DIAG=119
AT+CFUN=4
AT+CFUN=6
Note:
 Kama modem Ports zitapotea, nenda kwenye ile link tuliyotumia kule
juu      na zitaonekana tena zikiwa na  drivers installed.
 Hii sehemu si muhimu coz tunaenda kui flash modem so unaweza
kuiruka
 
FLASHING THE Hi Link MODEM
Kwa vile modem yetu imeshaweza kusoma ports, Inakuwa rahisi kuiflash
Fungua Universal MasterCode na tafuta Flash code(password) kwa kutumia
IMEI ya modem yako.
Sasa cha kufanya run Huawei HiLink Firmware kama kawaida tu, na tumia
flash code kama password yako
 
Subiri imalize hadi iandike SUCCESSFUL
 
HITIMISHO
Huawei HiLink modem is permanently unlocked na utaweza ku iconnect kwa
kutumia normal Huawei dashboard ingawa yenyewe haitakuwa na dashboard
sababu pamoja na process zote ulizofanya itabakia kuwa HiLink Modem!!
 
 
 
http://192.168.1.1/html/switchProjectMode.html
 
 
 
 
 
 
UNLOCK HUAWEI E173
 
 
Here are procedures on how to unlock Huawei Modem E173 with 35series of
IMEI
 
 
First you need to download and install QPST.2.7.378. after finishing to
installation, plug in your Huawei E173 with different simcar that can not
support on the modem then you will be notified by error that you can not use
that simcard then click on exit
 
1: Now go to Device Manager> port then locate your Modem then note down
COM port
 
 
2: Now search for the QPST .2.7.378. Start> Program> QPST 
 
 
3: Then click on Add new port.. the one you note down 
 
 
4: Uncheck "show  serial and USB/QS Diagnostic port only.
 
 
5: If you selected the correct port then it will shown like this
 
 
 
6: Then on the Tab click on Start clients then choose software Download 
 
 
 
7: Now the LIFE OF YOUR MODEM DEPENDS ON THIS STAGE your must
be very Careful. Click Back up tab then browser then choose location that will
save your Backup, then click on start and leave it till it finish to backup your
modem. remember that it finished complete and its saved on the location that
you selected  (.qcn) then continue with other stages. then quit QPST 
 
 
 
8: Now connect your computer with internet by phone or wireless or other
modem that  but not huawei 
 
Now open Huawei Modem Flasher  then on your left hand side choose Com
port of your Modem, Do not Worry you will see different port but its written
"3G PC UI  interface"
 
 
 
9: then click Read Modem info Tab. it read your modem info thet it says OK. if
its FAIL then there is problem on internet connection.
 
 
10: Then look on the tab then click "select Firmware" , Then choose "Extract
from EXE"  Then locate Firmware
file E1731Update_11.126.15.00.00.B416  and click ok
 
 
 
11: Uncheck 05.bin like this
 
 
 
12: Then On the tab choose "Flash Modem"  then choose "normal mode" then
wait till the box promt up and press OK after modem entered on download
mode
 
 
 
 
13: wait while new Firmware installing on your modem 
 
 
 
14: Remember you will get error on 07.bin. don worry, wait for while then it
will finish 
 
 
 
15: Now unplug your modem and plugin again you will see that modem won't
be able to have network and this becaue it loose its IMEI, So you need to
restore your modem. To do that you need to back on first steps on how to open
QPST  then.
 
 
Configuration then add COM port > software download insted of click back up
tab, click on restore tab then click browse then locate the file you created
Backup (7 stage) then click start and wait for while and it will finish 
 
 
 
16: after finish quit QPST then unplug your modem and plugin your modem. if
you followed the procedures well your modem 100% unlocked permanent and
you may use for any simcard, but remember it shows the same IMEI as Before
unlock.
 
 
 
 
 
UNLOCK ZTE MF180/190
 
 
I’ve used DC unlocker with lots of  ZTE modems including MF110, MF190,
MF180, MF673u and more. Unlike Huawei modems that can be easily
unlocked by generating the unlock code using the IMEI, there are certain steps
to take to unlock a ZTE USB modem with DC Unlocker. If your model number
is not listed, you can still try  it anyway.
You’ll need DC unlocker to get this done and you may download here.
How to Unlock ZTE Modems
 
- Insert an alien SIM into the modem, I mean an unsupported SIM from a
different network
- Plug in your USB modem to the computer and start the default modem
software. What I mean by the default program is the program from which you
connect the modem to your home network.
- When you’re prompted for an unlock code, close the program but be sure the
modem remains plugged in.
- Disconnect all internet connections and run DC Unlocker
 
 
- Under Select Manufacturer, choose ZTE datacards
- Under Select models, just leave it at Auto detect
- Click on the magnifying glass to search for your modem.
 
 
 
 
- When your datacard is detected, click on unlock. Your modem should be
unlocked after some seconds.

Supermarket: 0716586887 root1419_*^