GROUP 3 TRACK AND WORK EQUIPMENT

1. TRACK

1) TRACK ROLLER

2
1
3 4

Unit : ֮
No. Check item Criteria Remedy
Standard size Repair limit
1 Outside diameter of flange
٤185 
Rebuild or
2 Outside diameter of tread ٤150 ٤138
replace
3 Width of tread 36.5 42.5
4 Width of flange 22 -
Standard Tolerance Standard Clearance
Clearance between shaft size Shaft Hole clearance limit
5
and bushing 0 +0.031 0.021
٤60 1.5 Replace
-0.019 +0.021 to 0.050
Standard Tolerance Standard Interference bushing
Interference between roller size Shaft Hole Interference limit
6
and bushing +0.094 +0.030 0.045
٤68 -
+0.075 0 to 0.094
Standard clearance Clearance limit
7 Side clearance of roller Replace
0.2 to 0.6 1.5

7-37
2) CARRIER ROLLER

4 3
1
2

5
6

Unit : ֮
No. Check item Criteria Remedy
Standard size Repair limit
1 Outside diameter of flange
٤175 
Rebuild or
2 Outside diameter of tread ٤151 ٤141
replace
3 Width of tread 37.25 45
4 Width of flange 18.25 -
Standard size &Tolerance Standard Clearance
Clearance between shaft Shaft Hole clearance limit Replace
5
and support +0.003 +0.003 0.229 bushing
٤41.27 +0.017 ٤41.5 +0.002 to 0.25
1.2
Interference between shaft 0 +0.006 0.011
6 ٤50.8 -0.005 ٤50.8 +0.134 - Replace
and seal guard to 0.134

7-38
3) IDLER

8
2

6
1

7
3 5
4

Unit : ֮
No. Check item Criteria Remedy
Outside diameter of Standard size Repair limit
1
protrusion ٤552 
2 Outside diameter of tread ٤507 ٤491 Rebuild or
3 Width of protrusion 70 - replace
4 Total width 135 -
5 Width of tread 32.5 35.5
Standard size &Tolerance Standard Clearance
Clearance between shaft Shaft Hole clearance limit Replace
6
and bushing 0 +0.050 0.30 bushing
٤50 -0.030 ٤50.3 0 to 0.380
1.0
Clearance between shaft 0 +0.064 0.25
7 ٤50 -0.030 ٤50.025 0 1.0 Replace
and support to 0.317
Side clearance of idler Standard clearance Clearance limit Replace
8
(both side) 0.4 to 1.0 1.5 bushing

7-39
4) TRACK

2 1 6

5
4
3

Unit : ֮
No. Check item Criteria Remedy
Standard size Repair limit
1 Link pitch Turn or
171.07 174.4
replace
2 Outside diameter of bushing 50.61 46.57
3 Height of grouser 26 19 Rebuild or
4 Height of link 94.5 86.9 replace
Standard size &Tolerance Standard Interference
Interference between Shaft Hole interference limit
5
bushing and link 0 +0.02 0.036
٤50.68 -0.074 ٤50.25 -0.02 - Replace
to 0.45
Interference between 0 +0.05 0.258
6 ٤33.47 -0.062 ٤33.1 0 -
regular pin and link to 0.370
+5
Tightening angle method Initial tightening torque : 38 - 3 ָňU
7 Tight
(Tightening angle method) Additional tightening angle : 32Ň

7-40
5) TRACK FRAME AND RECOIL SPRING

21

Unit : ֮
No. Check item Criteria Remedy
Standard size Tolerance Repair limit
+2
1 Vertical width of idler guide Track frame 78 -1 82
0 Rebuild or
idler support 75 -1.5 71
+3
replace
Track frame 195 -1 199
2 Horizontal width of idler guide
idler support 190 - 188
Standard size Repair limit
Free Installation Installation Free Installation
3 Recoil spring Replace
length length load length load
٤192ţ410 405 8,497ָ  7,817ָ

7-41
2. WORK EQUIPMENT

A C D E F

B K J I H G

Unit : ֮
Criteria Criteria
Remedy
Measuring point Normal Recomm. Limit Recomm. Limit
&
Mark
(Pin and Bushing) valve service of service of
Remark
limit use limit use
A Boom Rear 70 69 68.5 70.5 71 Replace
B Boom Cylinder Head 70 69 68.5 70.5 71 Ō
C Boom Cylinder Rod 70 69 68.5 70.5 71 Ō
D Arm Cylinder Head 70 69 68.5 70.5 71 Ō
E Boom Front 70 69 68.5 70.5 71 Ō
F Arm Cylinder Rod 70 69 68.5 70.5 71 Ō
G Bucket Cylinder Head 70 69 68.5 70.5 71 Ō
H Arm Link 65 64 63.5 65.5 66 Ō
I Bucket and Arm Link 65 64 63.5 65.5 66 Ō
J Bucket Cylinder Rod 70 69 68.5 70.5 71 Ō
K Bucket Link 65 64 63.5 65.5 66 Ō

7-42