Torque Converter

TORQUE CONVERTER
A torque converter is used to connect the engine with the transmission.

A torque converter is a type of fluid coupling which transfers rotating power
from a prime mover, like an internal combustion engine, to a rotating driven
load.
In a vehicle with an automatic transmission, the torque converter connects the
power source to the load. It is usually located between the engine's flexplate
( a metal disk that connects the output from an engine to the input of a torque
converter in a car equipped with an automatic transmission ) and the
transmission.
The equivalent location in a manual transmission would be the mechanical

clutch. Thus it eliminates the need of a clutch in a car.
In a torque converter there are at least three rotating elements: the impeller,
which is mechanically driven by the prime mover; the turbine, which drives the
load; and the stator, which is interposed between the impeller and turbine so
that it can alter oil flow returning from the turbine to the impeller.
The Pump(impeller) is attached to the prime mover and is filled with hydraulic
fluid.
Due to the rotation of the pump, an increase in pressure due to the liquid is
observed and this liquid in turn turns the turbine. Thus engine power is
transferred to the transmission
The key to the torque converter's ability to multiply torque lies in the stator.
In the classic fluid coupling design, periods of high slippage cause the fluid flow
returning from the turbine to the impeller to oppose the direction of impeller
rotation, leading to a significant loss of efficiency and the generation of
considerable waste heat.
Under the same condition in a torque converter, the returning fluid will be
redirected by the stator so that it aids the rotation of the impeller, instead of
impeding it. The result is that much of the energy in the returning fluid is
recovered and added to the energy being applied to the impeller by the prime
mover. This action causes a substantial increase in the mass of fluid being
directed to the turbine, producing an increase in output torque.
Since the returning fluid is initially traveling in a direction opposite to impeller
rotation, the stator will likewise attempt to counter-rotate as it forces the fluid
to change direction, an effect that is prevented by the one-way stator clutch.
(The actual structure is the one showed above. Its made a little complicated so
that the impeller and the turbine are held fixed with the axis of the crank shaft)
Unlike the radially straight blades used in a plain fluid coupling, a torque
converter's turbine and stator use angled and curved blades. The blade shape
of the stator is what alters the path of the fluid, forcing it to coincide with the
impeller rotation. The matching curve of the turbine blades helps to correctly
direct the returning fluid to the stator so the latter can do its job. The shape of
the blades is important as minor variations can result in significant changes to
the converter's performance.
The key characteristic of a torque converter is its ability to multiply torque

when the output rotational speed is so low that it allows the fluid coming off
the curved vanes of the turbine to be deflected off the stator while it is locked
against its one-way clutch, thus providing the equivalent of a reduction gear.
This is a feature beyond that of the simple fluid coupling, which can Catch
rotational speed but does not multiply torque, thus reduces power losses.
It works in 3 phases.
1- Stall: In this phase the impeller rotates at a high speed but the turbine
doesn’t rotate since the driver applies brake.
2- Acceleration: The load is accelerating but there still is a relatively large
difference between impeller and turbine speed. Under this condition, the
converter will produce torque multiplication that is less than what could be
achieved under stall conditions.
3- Coupling. The turbine has reached approximately 90 percent of the
speed of the impeller. Torque multiplication has essentially ceased and the
torque converter is behaving in a manner similar to a simple fluid coupling. In
modern automotive applications, it is usually at this stage of operation where
the lock-up clutch is applied, a procedure that tends to improve fuel efficiency.

Torque Converter

Uploaded by

Copyright:

Available Formats

Torque Converter

Uploaded by

Document Information

Original Title

Copyright

Available Formats

Share this document

Share or Embed Document

Sharing Options

Did you find this document useful?

Is this content inappropriate?

Copyright:

Available Formats

Torque Converter

Uploaded by

Copyright:

Available Formats

How does a torque converter work?

What are the three main components of a torque converter?

TORQUE CONVERTER

A torque converter is used to connect the engine with the transmission.

The equivalent location in a manual transmission would be the mechanical

The key characteristic of a torque converter is its ability to multiply torque

You might also like