Relays and Optocouplers

Application Overview

Fotolia/...
Table of Contents

Features and Advantages 4

Selection Criteria for Relays 6

Long Cables and 2-Wire Sensors 8

Modern Lighting with Electronic Control Gear 10

Functional Safety 12

The Contact Material Is Crucial 14

Relays with Manual Operation 18

Relays with a Wide Input Voltage Range 20

Rail-Specific Requirements 22

Switching DC Loads 26

Optocouplers and Solid-State Relays 28

Glossary 32

Connection Technology 35
iStock.com/ lagereek

FEATURES AND ADVANTAGES

Relays / Optocouplers
Relay or Optocoupler?

Relay Optocoupler/Solid-State Relay

• Electrically isolate input and output circuits

• Adjust different signal levels
• Amplify and/or multiply signals

Immunity to electromagnetic interference and transient voltages Long service life – no mechanical wear on contacts

High, short-term overload on both input and output sides High switching frequency due to short switch-on
without losing functionality and switch-off times

Minimal switching loss/high switching power Unfazed by shock and vibration

A single module switches both direct and alternating current

No contact bouncing
(highly versatile)

No leakage current in the load circuit (air insulation) “Noiseless” switching

Multiple contacts possible

Low control power
(control signal switches multiple load circuits)

Switching state is partially visible to the naked eye Short response times

No electromagnetic radiation from switching sparks or coils –

Safe isolation between coil and contact set no interference with adjacent modules or electronic components
during switching

Read about “Relays” on page 6 Read about “Optocoupler and SSR modules” on page 28

4
©leungchopan/Fotolia.com

Distinguishing between Optocoupler and Solid-State Relay

Optocoupler Solid-State Relay

Mounted or soldered to the PCB Pluggable on socket

- Not replaceable - Can be replaced in case of repair

A large number of variants enhances application flexibility Seamless change from electronic to electromechanic
and range switching element

5
 SELECTION CRITERIA FOR RELAYS
It’s in the Details

1) Coil 2) Contacts
Coil voltage; maximum continuous voltage; Contact arrangement; contact loading;
response voltage and pick-up current; contact material; service life; contact resistance;
drop-off voltage and dropout current isolation requirements; limiting continuous current

In industrial applications, relays are proven interface mo- 5) Other criteria

dules that can handle a variety of tasks. However, some Ambient temperature;
points must be considered when selecting the right relay dielectric strength;
module . These points include the nominal voltage of the mounting conditions,
coil, as well as the number of relay break contacts, make IP degree of protection;
contacts and changeover contacts. The contacts are approvals
important for the service life. The contact material has to
be selected depending on whether inductive, capacitive
or resistive loads will be connected.
This application overview provides important information
for selecting relays.

6
©Friedberg/Fotolia.com

3) Switching time 4) Mechanical properties

Response time; drop-out time; Vibration resistance; shock resistance;
switching frequency; bounce time size and space

iStock.com/Bartosz Hadyniak ©Netzer Johannes/Fotolia.com

7
 LONG CABLES AND 2-WIRE SENSORS
Reliably Switch despite Coupling

To switch on, relay modules require the nominal What are the causes and how can they be solved?
voltage UN. For operation, however, the holding Long, parallel lines are capacitively coupled
voltage at only 15 % of the nominal voltage is suffi- to each other. Energy is then transferred to an
cient. In standard circuits, all relay modules operate adjacent conductor. Active 2-wire sensors, such
reliably. In circuits with long, parallel lines, in circuits as proximity switches or level monitors, normally
with active 2-wire sensors or with digital AC control require a minimum continuous current to ensure
outputs, however, a low holding voltage often leads that the holding voltage is maintained on the relay
to malfunction. The modules no longer switch off . control lines. Because of this behavior, the relay
This eff ect often occurs when updating systems, cannot switch correctly.
changing old “power-hungry” to current “pow- For such applications, WAGO has developed spe-
er-saving” relay modules. cifi c RC base load modules against interference
coupling and integrated them into the relay modu-
les. The modules minimize the unwanted voltages
at low loss and allow defined switching.
1 2 3 4 5 16 27 38 4 5 6 7 8

Application example, 230 VAC

ON

triac outputs from

ON

controllers

L1 N

Reliability 24/7: WAGO’s sockets that have a miniature switching re-

lay and base load module ensure safety and dependability at voltage
levels below an application’s release voltage. ©kawinnings/Fotolia.com

8
 Application example, line capacity (level measurement)

230 VAC

L1
N

N
C1

L (line length)

Application example, 2-line sensors (parcel load detection)

230 VAC

Is
L1

Limiting Continuous
Description Item No. Nominal Input Voltage VN
Current

Relay module with

1 changeover contact, 857-358/
230 VAC 6A
with integrated base 006-000
A1

A2

load module

Relay module with

1 changeover contact,
857-368/
A1
with integrated base 230 VAC 6 A*
006-000
load module and gold
A2

contacts

* To prevent the gold layer from being damaged, 30 VDC switching voltages and 50 mA currents shall not be exceeded.
Higher switching power eventually evaporates the gold layer. The resulting deposits in the housing may reduce the service life.

9
 MODERN LIGHTING WITH ELECTRONIC
CONTROL GEAR
Brief Current Peaks – Fatal Consequences

Equipped with electronic control gear (ECG), mo- What should be considered when planning lighting
dern lights offer numerous advantages. They gene- systems?
rate flicker-free light with high levels of efficiency. When selecting relays, the inrush current must
Both in planning new and replacing old lighting absolutely be considered. Standard relays quickly
systems, the inrush current of the ECG must be a reach their limits. For such applications, WAGO has
central focus. developed relay modules with contacts that safely
A capacitor in the input circuit of many ECGs control brief high peak inrush currents. The con-
causes a substantial current peak when switched tact material reliably prevents the contacts from
on that can exceed far more than ten times the catching or fusing.
nominal current. Even if the current lasts for just a For maximum inrush currents, relay modules with
few milliseconds, it can cause the relay contacts to two contacts working in parallel are available. The
fuse together. first contact consisting of high-strength tungsten
catches the current peak. The second contact
consisting of highly conductive silver alloy mana-
ges the operational current.
As an alternative to relays, the WAGO product port-
folio includes optocouplers and solid-state relays
for use with capacitive loads. Special designs with
zero voltage switches minimize the peaks.

10
 ©panthermedia.net/scanrail
When switching on lamps, substantial current peaks briefly occur.
The unwanted effect of wear and contact erosion can be prevented
by lamp load relays.

Relay Selection for Lamp Loads

Limiting Continuous
Description Item No. Nominal Input Voltage VN
Current

Relay module with 1 chan-

geover contact and status
788-354 24 VDC 16 A
indication, max. inrush current
120 A / 50 ms

14 Relay module with 1 make

contact and status indication, 788-357 24 VDC 16 A
13
max. inrush current 165 A / 20 ms

A1
+ 14
Solid-state relay module,
788-720 24 VDC 1A
A2 13
zero voltage switch
-

A1 13
Solid-state relay module,
788-721 24 V AC/DC 4A
14
zero voltage switch
A2

A A = Automatik (AUTO)
0 = AUS

Relay with 1 make contact,

0
1 1 = Manuell EIN (MAN)
A1 14
+

Manual/OFF/Auto switch with 789-324 24 VDC 16 A

(+24V) A3
+
B1

feedback contact
n.c.
B2 13 13
A2
-
A2
-

11
 iStock.com/Richard Clark
Signal monitoring: Relays with force-guided contacts make it
possible to quickly detect errors such as opening failures.

FUNCTIONAL SAFETY
Detect Errors in Safety-Related Circuits
To comply with relevant policies and regulations for
functional safety, the use of special components is
Short circuit
compulsory. These components must meet strict
in the output contact
requirements. For relay modules, force-guided
Auxiliary break
contacts with at least one break contact and make Safety contacts,
contacts for
safety circuits
contact are required. They must be connected me- force-guided
prohibited
13 23 33 41
chanically so that break contacts and make contacts
cannot be closed or opened at the same time. This
allows errors due to opening failures to be clearly
identifi ed. Only errors due to opening and isolation
failures are of importance in safety-related matters.
K1
In a circuit, an open break contact can be detected
by a closed break contact. The same applies to a
closed make contact when the break contact is open.
K2
Of course, EN 50205 requirements also apply to
K2
relays with changeover contacts in safety-related cir-
cuits. It stipulates that per changeover contact, only
the break contact or make contact can be used and
the changeover contacts must be positively driven.
Therefore, only relays with at least two changeover
14 24 34 42
contacts can be used in safety-related circuits.

12
 ©th-photo/Fotolia.com

The EN 50205 standard diff erentiates between

two contact sets by the type of positively
driven operation:
Type A: Relay in which all the contacts are mecha-
nically connect
Type B: Relays that have both mechanically
Type A Type B connected and non-mechanically connected
Typ A Typ B
contacts

Relay Selection for Safety Relays

Limiting Continuous
Description Item No. Nominal Input Voltage VN
Current

Safety relay module SR2M

(2 changeover contacts) with force-guided 788-384 24 VDC 6A
contacts (type A) and status indication

Safety relay module SR2M

(2 changeover contacts) with force-guided 788-906 24 VDC 0,3 A
gold contacts (type A) and status indication

Safety relay module with 4 break

contacts and 4 make contacts, relay
288-414 24 V AC/DC 6A
pre-soldered onto carrier, force-guided
contacts, type B

13
 THE CONTACT MATERIAL IS CRUCIAL
Small Circuit Loads/Harsh Environment

Standard relay contacts are normally made of silver There is not enough energy to break up and clean
alloys such as silver nickel, silver tin oxide or silver the oxide layer thermally. This results in malfunc-
cadmium. They are well suited for use in a variety tions that can be prevented using hard, gold-plated
of applications. However, they are limited to small contacts. Gold does not form an oxide layer and
loads, currents and voltages. The surfaces of the is also very resistant against corrosion in adverse
sliver alloys are prone to oxidation, which leads to conditions.
an increase in contact resistance. It is not a roblem WAGO has added a relay version with hard, gold
when switching larger loads because ever smaller plating to the relay portfolio for switching small
cleaning electric arcs result. That is not the case for loads. They are intended for such applications and
smaller loads. guarantee reliable signal transmission over a long
period.

Prevent malfunctions: Relays with hard, gold-plated contacts

are particularly well suited for switching small loads.
©Stitched Panorama/Fotolia.com

14
Contact Material Application Area

AgNi – silver-nickel contact Resistance loads

Weak inductive loads
For normal or higher power

AgSnO2 – silver tin oxide contact For high switching loads, primarily in supply voltage applications with high
inrush currents
Very low tendency to fuse, good burn-off resistance
Low material material migration when switching from DC

AgCdO– silver cadmium contact Inductive AC loads

For high switching loads, primarily in supply voltage applications
Low tendency to fuse, good burn-off resistance

AgNi + Au – silver-nickel contact with hard gold plating Small load range
Very corrosion resistant; important material for reliable contact at low
switching capacities

15
 ©tuastockphoto/Fotolia.com
In chemical plants, sewage plants or in steel production,
aggressive gases always have to be taken into account: Relays
with gold contacts protect against oxidation and corrosion.

THE CONTACT MATERIAL IS CRUCIAL

Small Circuit Loads/Harsh Environment

In some sectors of industry, like chemical plants How can malfunctions be prevented?
and steelworks, as well as in sewage plants, Like switching smaller loads, hard, gold-plated con-
aggressive gasses are common. Higher pollution tacts excel in these applications. Relays equipped
levels, as well as high humidity and high temperatu- with gold-plated contacts operate reliably in small
res negatively impact electrical components. load applications up to 50 mA and 30 V. For these
Relay modules with contacts made of silver alloys jobs, WAGO has developed a relay model that gua-
are not the fi rst choice. The contact surfaces oxi- rantees reliable operation.
dize preventing switching operations from applying
enough energy to reliably break up the oxide layer
thermally. Malfunctions then result.

16
Relay Selection with Gold Contacts

Limiting Continuous
Description Item No. Nominal Input Voltage VN
Current

857-314 24 VDC

Relay module with 1 changeo-

ver contact, with gold cont- 6 A*
acts, for normal switching

857-368 230 VAC/DC

A1

A2

14
A2
–
11
859-314 24 VDC
A1
+ 12 Relay module with 1 changeo-
ver contact, with gold cont- 5 A*
14
acts, for normal switching
859-359 230 VAC
A2
~ 11

A1
~
12

788-412 24 VDC

Relay module with 2 changeo-

ver contacts, with gold cont- 8 A*
acts and status indication
788-616 230 VAC

14
11
12
24
A1
+ 21

858-314 24 VDC
22
34
31
A2
- 32
44
41 Industrial relay module,
42

14 4 changeover contacts with 5 A*

gold contacts
11
12
24
A1
~ 21

858-518 230 VAC

22
34
31
A2
~ 32
44
41
42

*To prevent the gold layer from being damaged, 30 VDC switching voltages and 50 mA currents shall not be exceeded.
Higher switching power eventually evaporates the gold layer. The resulting deposits in the housing may reduce the service life.

17
 RELAYS WITH MANUAL OPERATION
Switch Manually and Electrically

To switch individual circuits specifi cally without Mechanical or Electrical Manual Operation
actuating the controller has a number of tangible
advantages in a number of applications, e.g., at WAGO off ers to alternatives for the relay modules
start-up. For complex building control systems, with manual operation. Version one is designed
individual building systems can be checked and for front panel manual operation, i.e., the contacts
commissioned independently of the controller are only closed manually. In manual operation, the
setup. The same applies to commissioning in modules are limited to approximately 100 switching
industrial processes. When troubleshooting, or to operations. In automatic mode, these modules
ensure limited manual operation, service and main- complete the usual switching operations of the
tenance personnel appreciate the option of manual relay.
operation. With the second version with manual operation, the
relay coil is electrically connected. The operating
status can be set via a Manual/OFF/Auto switch
on the front panel. The relay modules complete
the usual switching operations of the relay without
limitation.

Application example,
1 2 3 4 5 6 7 8

building automation
ON

Extremely practical in building automation and process control:

Increased system uptime in the event of a controller failure
thanks to a relay with manual operation. ©leungchopan/Fotolia.com

18
Relay Selection with Manual Operation

Limiting Continuous
Description Item No. Nominal Input Voltage VN
Current

Relay module with 1 changeover

A1 14 contact, electrical and mecha-
788-341 24 VDC 16 A
+
11
12 nical status indication, manual
A2
- operation

Relay module with 2 changeover

14
A1 11

contacts, electrical and mecha-

+
12

788-346 24 VDC 8A
nical status indication, manual
24
A2
21
-
22
operation

14 Relay module with 1 changeover

contact, manual operation for
A1 12
+
789-1341 24 VDC 12 A
manual start-up, electrical and
A2
–
11 mechanical status indication

14
12
Relay module with 2 changeover
contact, manual operation for
A1 24
+ 22
789-1346 24 VDC 8A
manual start-up, electrical and
mechanical status indication
A2
– 21
11

14
11 Industrial relay module,
4 changeover contacts, manual
12
24
A1
+ 21

operation for manual start-up, 858-304 24 VDC 5A

22
34
31

electrical and mechanical status

A2
- 32
44

indication
41
42

Industrial relay module,

A1
14
11
2 changeover contacts, manual
operation for manual start-up, 858-324 24 VDC 12 A
+
12
24

electrical and mechanical status

21
A2
- 22

indication

Relay Selection with Manual/OFF/Auto Switch

Limiting Continuous
Description Item No. Nominal Input Voltage VN
Current

A A = Automatisk

Lamp load relay module with

0 0 = OFF
1 1 = Manuell PA
A1 14

1 make contact, Manual/OFF/ 789-323

+
(+24V) A3
+

A2
-
13 13
Auto switch
A2
-

24 VDC 16 A
Lamp load relay module with
A A = Automatisk
0 0 = OFF
1 1 = Manuell PA
A1

1 make contact, Manual/OFF/

+ 14
A3

789-325
(+24V)
+
B1

n.c.
B2 13 13
Auto switch with feedback
contact
A2
-
A2
-

19
 RELAYS WITH A WIDE INPUT VOLTAGE RANGE
Versatile

In principle, the relay modules with a wide input vol- They are recommended for a number of applica-
tage range are well-rounded, making them perfect tions, e.g., service and maintenance. Technicians
for virtually any application. Like the WAGO standard and maintenance specialists need only one relay
relay modules, they comply with all relevant stan- module for all voltages that is immediately acces-
dards and regulations. These relay modules are de- sible in the case of error to replace a defective mo-
signed for DC and AC voltages from 24 V to 230 V, dule. A comprehensive inventory of relay modules
can connect limiting continuous currents up to 6 A for various voltage ranges is no longer necessary.
and have the same number of switching cycles as The “One module for all applications” principle also
the standard versions. optimizes production and storage for manufactu-
rers with small production runs that are exported
internationally. They need only one relay module
as the world standard. For ease of use and reliable
electrical connections, WAGO equips the relay
modules with push-in CAGE CLAMP® connection
technology.

Storage and maintenance costs can also be signifi cantly

reduced because one single module covers nearly all standard
voltage ranges.

20
 ©industrieblick/Fotolia.com

Limiting Continuous
Description Item No. Nominal Input Voltage VN
Current

Relay module with 1 changeover

857-359 24 V … 230 V AC/DC 6A
contact, for normal switching

Relay module with 1 changeover

contact, with gold contacts, for 857-369 24 V … 230 V AC/DC 6 A*
normal switching

*To prevent the gold layer from being damaged, 30 VDC switching voltages and 50 mA currents shall not be exceeded.
Higher switching power eventually evaporates the gold layer. The resulting deposits in the housing may reduce the service life.

21
Within railway applications, there are special requirements for ©TTstudio/Fotolia.com

relays including operating voltage, ambient temperature and

shock/vibration resistance: Relays from WAGO meet these
requirements.

RAIL-SPECIFIC REQUIREMENTS
Master Voltage Fluctuations

Railway systems have two fundamental areas of Brief spikes up to 1.4 times the nominal voltage may
application: There are the fi xed installations in signal not cause any damage. Deviations from these rules
boxes, turnout systems and access systems on the only apply to components powered by stabilized vol-
one hand. On the other, there are installations in rail tage supplies. Fluctuations of ±10 % of the nominal
vehicles. Of central importance in this area is EN voltage are permitted – values common for industrial
50155, which differs significantly from traditional applications.
industrial standards. All components used in railway
applications must operate reliably at voltages bet-
ween 70 % and 125 % of the nominal voltage.

22
Relay Options for Railway Systems

Limiting Continuous
Description Item No. Nominal Input Voltage VN
Current

14 Relay module with 1 chan-

geover contact, with input
A2
–
11
859-390 24 VDC 3A
voltage range
A1
of ‒30 … +25 %
+ 12

Relay module with 1 chan-

geover contact, with input
859-398 24 VDC 3A
voltage range
of ‒40 … +40 %

14 Relay module with 1 changeover

A2
– contact, with gold contacts,
11 859-392 24 VDC 3 A*
with input voltage range
of ‒30 … +25 %
A1 12
+

Relay module with 1 changeover

contact, manual operation and
A1 14
788-391 24 VDC 3A
+
11
12 extended input voltage/tempe-
A2
- rature range

A1
14 Relay module with 2 changeover
11
+ contacts, manual operation and
788-390 24 VDC 3A
12

A2
24
extended input voltage/tempe-
21
rature range
-
22

14
11

A1
12
24
21
Relay module with 4 changeover
contacts and extended input 858-354 24 VDC 5A
+
22
34

voltage/temperature range
31
A2
- 32
44
41
42

14
11
12 Relay module with 4 changeover
contacts and extended input
24
A1
+ 21

858-355 24 VDC 5 A*
22

voltage/temperature range,
34
31
A2
- 32

with gold contacts

44
41
42

*To prevent the gold layer from being damaged, 30 VDC switching voltages and 50 mA currents shall not be exceeded.
Higher switching power eventually evaporates the gold layer. The resulting deposits in the housing may reduce the service life.

Optocoupler Options for Railway Systems

Limiting Continuous
Description Item No. Nominal Input Voltage VN
Current

A2 2
Optocoupler module with exten-
ded input voltage and temperature 859-798 12 VDC 100 mA
– –

RL

A1
+
1
+ range, for railway applications

A2
–
2
–
Optocoupler module with exten-
RL ded input voltage and temperature 859-794 24 VDC 100 mA
range, for railway applications
A1 1
+ +

A1
+
1
+
Optocoupler module with exten-
ded input voltage and temperature 859-795 5 VDC 100 mA
RL

range, for railway applications

A2 2
– –

23
Photo: vossloh

RAIL-SPECIFIC REQUIREMENTS
Ambient Operating Temperature and Mechanical Influences

Components such as relay modules are exposed to The WAGO relay modules meet all requirements for
extreme temperatures of ‒40 °C to +70 °C in railway use in railway operations in categories 1A to 1B. Due
applications depending on the area of application. to the spring-loaded connection, they also offer high
This is because the control cabinet is sometimes shock and vibration resistance.
installed in steel housings below the passenger
compartment that are not climate controlled. In prin-
ciple, depending on the place of installation and heat
ratio, the railway divides the areas of application for
electrical components into four temperature classes,
from T1 to TX.
Experience has shown that a number of applications
fall in class T3, which corresponds to the tempera-
ture range of ‒25 °C to +70 °C. All WAGO relay modu-
les for railway applications correspond to the highest
classes of T3 or TX.
Loads due to vibration and shock are also significant
in railway vehicles. EN 61373 “Railway applications –
Rolling stock equipment – Shock and vibration tests”
describes the mechanical influences in detail caused
by operation.

Test set-up for me-

chanical influences
during operation

24
 M

I
Internal cabinet
N Vehicle cabinet

K
F
Subassembly

O
J
Underfloor cabinet D

G Bogie

H
Wheelset

Vibration and Shock: Classification per EN 61373

Category Location Description of Device Location

MNO
1 Class A Components attached directly to or in the vehicle
I and J

1 Class B D Components installed in a underfl oor cabinet which in turn is attached to the vehicle body

1 Class B K and E Components installed in a large internal cabinet which in turn is attached to the vehicle body

Components as elements of subassemblies installed in a cabinet which in turn is attached

1 Class B F
to the vehicle body

2 G Cabinets, subassemblies, devices and components attached to the bogie of a railway vehicle

3 H Cabinets, devices and components or assemblies attached to the wheelset of a railway vehicle

Ambient Operating Temperature per EN 50155

External Vehicle Ambient Internal Cabinet Internal Cabinet Overtemperature Air Temperature
Temperature Temperature (< 10 min) on the PCB

T1 ‒25 … +40 C° ‒25 … +55 C° +15 K ‒25 … +70 C°

T2 ‒40 … +35 C° ‒40 … +55 C° +15 K ‒40 … +70 C°

T3 ‒25 … +45 C° ‒25 … +70 C° +15 K ‒25 … +85 C°

TX ‒40 … +50 C° ‒40 … +70 C° +15 K ‒40 … +85 C°

25
 DC load limit curve DC load limit curve DC load limit curve
788-312 858-391 858-304, -308
Switching current (A)

Switching current (A)

Switching current (A)

20 2-pole 20 20
resistive load DC resistive load DC resistive load
10 10 10
1 Contact
5 5 5
2 Contacts in series
2 Contacts
3 Contacts in series
in series
4 Contacts in series
2 2 2

1 1 Contact 1 1
1 Contact
0.5 0.5 0.5
2 Contacts in series
3 Contacts in series
0.2 0.2 0.2
4 Contacts in series DC inductive load,
L/R = 40 ms
0.1 0.1 0.1
10 20 30 50 100 200 300 10 20 30 50 100 200 300 10 20 30 50 100 200 300

Switching voltage (V) Switching voltage (V) Switching voltage (V)

SWITCHING DC LOADS
Contacts Connected in Series Improve Load Limit Curve

Applications in DC relays are limited to selected An albeit significantly weakened effect can be
areas, which are often battery-backed to increase achieved with “series-connected contacts” as the
availability. Such applications include controller DC load curves show. Because the contacts are
instrumentation and control in power plants, slightly offset in time, the double values are not
chemical systems or railway systems. Safely achieved like for a single contact with double
switching DC loads requires sophisticated tech- distances.
nology. Unlike AC loads, the switching arc is not
extinguished automatically with the zero voltage. Static electric arc limit curve
For DC loads, the arc length is largely dependent 3 1 Arc-free wiring Schaltungen
Lichtbogenfreie
Switching current (A)

on the voltages and currents to be switched as the 2 Instable,

Instabile, short
kurze arcs
Lichtbögen
static electric arc limit curve shows. The more pro- Glimmentladung
3 Glow discharge
nounced the electric arc, the shorter the service Voll ausgebildete
4 Fully qualified switching arcs
life of the relay. If the limit curve is exceeded, the Schaltlichtbögen
electric arc is no longer extinguished and the relay
is destroyed.
Structurally, the service life can be achieved by
increasing the contact distance. However, clear 4
limits are set here by the relay design.

2
1

Switching voltage (V)

26
 ©panthermedia.net/Leung Cho Pan
High DC voltages in battery-backed process control systems:
Relay with contacts connected in series control arcs.

Relay Selection for DC Loads

Limiting Continuous
Description Item No. Nominal Input Voltage VN
Current

Relay module with 2 changeover

788-312 24 VDC 8A
contacts and status indication

14
11

A1
12
24 858-304 24 VDC
Industrial relay module,
+ 21

5A
22

4 changeover contacts
34
31
A2
32

858-308 220 VDC

-
44
41
42

14
11
12
24
A1
Industrial relay module,
+ 21

858-391 220 VDC 6A

22

4 changeover contacts
34
31
A2
- 32
44
41
42

27
Ideal for production lines: Optocouplers distinguish themselves
with long service lives and short clearing times.

OPTOCOUPLERS AND SOLID-STATE RELAYS

Durable and Wear-Free

WAGO has developed a wide range of optocoupler For areas of application with high switching peaks,
and SSR modules for industrial applications. The WAGO has developed optocouplers and solid-sta-
optocouplers are directly integrated into the te relays with zero voltage switch. These minimize
housing for all WAGO optocoupler modules. SSR peaks.
modules are interchangeable solid-state relays
that are PIN compatible with all standard relays. As an interface module between process periphe-
There is an extensive portfolio with versions for rals, as well as control and signaling equipment,
both DC and AC voltages. They are designed for optocouplers and solid-state relays (SSR) impress
nominal voltage ranges in the input of 5 V to 230 V with the following advantages:
and in the output between 3 V and 280 V. • Long service life
The integrated protective circuit ensures sound • No mechanical wear
operation in all applications. The modules switch • No contact bouncing
loads with inrush and switch-off currents equally. • Short clearing times
These include incandescent bulbs with resistive • Low inrush current
and ECG with capacitive load to the originators • Silent
of high inrush currents, magnet valves with their • Shock- and vibration-resistance
inductive coils to the originators of burdening
switch-off currents.

28
 ©Hamik/Fotolia.com

-
1 2 3 4 5 6 7 8
ON

Application example: Galvanic isolation, e.g., rev counter

1 2 3 4 5 6 7 8
ON

Application example: Signal amplifi cation, e.g., compressed-air valve

29
OPTOCOUPLERS AND SOLID-STATE RELAYS
Durable and Wear-Free

Selection for DC Load, 2-Wire Connection

Nominal Input Output Voltage Limiting Continuous

Description Item No.
Voltage VN Range Current

14

13
857-704 24 VDC 0 … 48 VDC 0.1 ADC
N.C.

Solid-state relay module

14

857-724 24 VDC 0 … 24 VDC 3 ADC

13

N.C.

A1 14 -
+

Solid-state relay module 788-700 24 VDC 0 … 24 VDC 3.5 ADC

A2 13 +
-

A1 14 -
+

Solid-state relay module 788-701 24 VDC 0 … 30 VDC 5 ADC

A2 13 +
-

A1 1
+ +
RL
859-796 24 VDC 3 … 30 VDC 100 mA
A2 2
– –

A1 1
Optocoupler module
+ +
RL
859-795 5 VDC 3 … 30 VDC 100 mA
A2 2
– –

A2 13
–

RL 859-761 24 VDC 3 … 30 VDC 3A

A1 14
+

13 A2
–
Power optocoupler
RL
module 859-762 24 VDC 3 … 30 VDC 3A
14 A1
+

A2 -2
–

RL
859-744 48 VDC 3 … 53 VDC 4A
A1
+ A

30
Selection for DC Load, 3-Wire Connection

Nominal Input Output Voltage Limiting Continuous

Description Item No.
Voltage VN Range Current

A1 24V
Power optocoupler mo-
859-720 24 VDC 10 … 30 VDC 3A
+
RL

A2
A
dule, negative switching
–
0V

859-702 24 VDC 20 … 30 VDC 500 mA

Optocoupler module,
A2 0V
—

859-708 24 VDC 20 … 30 VDC 500 mA

negative switching
 A
RL
A1 UN
+

859-706 24 VDC 4 … 6.25 VDC 500 mA

859-752 5 VDC 20 … 30 VDC 500 mA

Optocoupler module,
A2 0V
—

859-758 24 VDC 20 … 30 VDC 500 mA

RL

positive switching
 A

A1
+ +24 V

859-756 24 VDC 4 … 6.25 VDC 500 mA

Selection for AC Load

Nominal Input Output Voltage Limiting Continuous

Description Item No. Range
Voltage VN Current

14

13
Solid-state relay module 857-714 24 VDC 24 … 240 VAC 2 A AC
N.C.

A1
+ 14

Solid-state relay module 788-720 24 VDC 24 … 240 VAC 1 A AC

A2 13
-

A1 13

A2 14
Solid-state relay module 788-721 24 V AC/DC 12 … 275 VAC 4 A AC

31
 GLOSSARY
Respond Freewheel diodes
Change in the switching position of a relay from Recovery diodes are primarily used to protect
the idle state (e.g., make contacts open) to the against overvoltages that arise when switching
working state (e.g., make contacts closed) caused off an inductive DC load (electric motor, relay coil)
by applying the power; this process was formerly by self-induction. Voltage peaks are limited to the
called “tightening.” value of the diode forward voltage and overruns
diverted via the diode. However, this leads to a
Bistable relay delay in the voltage drop and switching operation.
Electrical relay that remains in the achieved swit-
ching state after switching off the power; to return Electrical isolation
to the initial state, another suitable state (e.g., Potential-free isolation between electrical parts;
triggering the reset coil) is necessary. with galvanic isolation, no charge carriers flow
from one circuit to another, i.e., there is no elec-
Inrush current trically conductive connection between circuits.
The indication of the maximum inrush current However, the circuits can still exchange electrical
specifies which peak current is allowed when swit- power or signals and specifically via magnetic
ching on a contact under defined conditions (e.g., fields, by means of infrared radiation or charge
voltage, power factor, time response) without the displacement.
relay then malfunctioning. The inrush current can
often be much higher. Solid-state relay
Solid-state relay with a switching element that is
Electrical service life an electronic component, e.g., transistor, thyristor
Number of switching cycles until the relay fails or triac; solid-state resistors that boast wear-free
under a specified electrical load and defined operation; compared to relays, they have a high
operating conditions; the standard service life switching frequency. Galvanic isolation is achieved
values usually apply to the maximum permissible by an integrated optocoupler.
resistive load. For smaller switching loads, a much
longer service life is expected. For larger swit- Contact type
ching loads, the service life is greatly reduced. The three most important contact types (also
called the contact spring set) are make contact,
Electrical relay closed contact and changeover contact.
Component that generates sudden predeter- They are abbreviated as follows:
mined changes to one or more output criteria Germany UK America
when certain requirements in the excitation circuit Make contact 1 make A SPST-NO
(input circuit) are met. (normally open)
Break contact 2 break B SPST-NC
Electromechanical relay (normally closed)
Electrical relay in which the electrical current Changeover changeover C SPDT
effects mechanical movements in the excitation contact 21
circuit that execute the operation in the output
circuit. Creepage distance
Shortest distance between two conductive parts
measured along the surface of an insulating
material.

32
Short-circuit-protected Optocoupler
Switching off the final stage of a solid-state relay Optocouplers are electronic components with
to protect the output circuit against destruction in which a load current is switched via a control
the event of a short circuit. circuit. Unlike electromechanical relays, optocou-
plers have no mechanical parts prone to wear.
Load category (solid-state relay) Load classifica- In the control circuit, a light signal is triggered
tion for solid-state relays according to EN 62314 for the switching operation via an LED that in a
photosensitive semiconductor receiver causes
LC A – Resistive loads or low inductive loads the closure of an applied load circuit. Sender (LED)
LC B – Motor loads and receiver (e.g., phototransistor) are embedded
LC C – Electrical discharge lamps in a light-conductive plastic and surrounded by an
LC D – Incandescent lamps opaque envelope that protects against external
LC E – Transformers influences.
LC F – Capacitive loads
Bounce time
Leakage current Time from the first to the final closure (or opening)
Current on the load side of an optocoupler that of a contact caused by shock processes of the
flows in the locked state of the output stage. Clea- contact movement; these shock processes are
rance Shortest air space between two conductive called “contact bouncing.”
parts.
Release time
Mechanical service life Time between switching off the coil excitation
Number of switching cycles during which the relay and the first opening of the make contact or first
remains functional with current-free switching closing of the break contact.
contacts.
Switching inductive load
Monostable relay For inductive loads mainly present when using
Electrical relay that returns to its initial state after coils in the load circuit, the problem arises when
switching off the energizing quantity. switching off. A magnetic field forms from the cur-
rent flow in the coil that suddenly collapses and
Normally closed contact generates a high induction voltage. This voltage
The contact is closed when the relay is in the idle peak must be short circuited by a diode connec-
state and open when the relay is in the working ted in parallel. However, the time needed leads to
state. a fall delay.

33
 GLOSSARY
Switching capacitive load
Capacity loads occur when there is capacitor in RT III: Wash tight (washable) relay
the load circuit. This acts like a short circuit when Relay capable of being automatically soldered and
switching on and causes a high inrush current. If subsequently undergoing a washing process to
the current is no limited, it can destroy the semi- remove flux residues without allowing the ingress
conductor. of flux or washing solvents.
RT IV: Sealed relay
Switching resistive load Relay provided with a housing that has no vents to
Because the amperage in the load circuit and the the outside atmosphere, and has a time constant
voltage via the semiconductor behave inversely better than > 2x104 s (IEC60068-2-17).
proportional to each other for resistive loads, the- RT V: Hermetically sealed relay
re is usually no problem. Maintaining the maximum Sealed relay having an enhanced level of sealing,
amperage and voltage levels of the components assuring a time constant better than > 2x106 s
is sufficient here. There is a special case when (IEC60068-2-17).
switching incandescent bulbs. Due to the low
cold resistance, overcurrents at 10 to 20 times Changeover contact
the operating current can arise when switching Compound contact consisting of break contact
on. The components must be designed for these and make contact with a common terminal; if one
potential overloads that correspond to the effect of the contact circuits is open, the other is closed.
with capacitive load.

Switching cycle
The response and relapse of a relay as a result of
switching on and off the power.

Make contact
The contact is closed when the relay is in the
working state and open when the relay is in the
idle state.

Switching current
Current (AC or DC) that can switch a relay contact
on and off. Degree of protection, categories for
elementary relays according to IEC 61810:
RT 0: Unenclosed relay
Relay not provided with a protective housing.
RT I: Dust-protected relay
Relay provided with a housing that protects its
mechanisms from dust.
RT II: Flux-proof relay
Relay capable of being automatically soldered
without allowing the migration of solder fluxes
beyond the intended areas.

34
CONNECTION TECHNOLOGY

This connection technology is included in the following:

788 Series 857 Series 858 Series

This connection technology is included in the following:

859 Series 789 Series 288 Series

35
 0888-0192/0202-6901 – RELAYS & OPTOCOUPLERS 2.2 US – 02/2016-00 – Printed in Germany – Subject to design changes

WAGO Kontakttechnik GmbH & Co. KG

Postfach 2880 · 32385 Minden Headquarters +49 571/ 887 - 0
Hansastraße 27 · 32423 Minden Sales +49 571/ 887 - 222
[email protected] Order Service +49 571/ 887 - 44333
www.wago.com Fax +49 571/ 887 - 8 44169

WAGO is a registered trademark of WAGO Verwaltungsgesellschaft mbH.

”Copyright – WAGO Kontakttechnik GmbH & Co. KG – all rights reserved. The content and structure of the WAGO websites, catalogs, videos, and other WAGO media are subject to
copyright. Distribution or modification to the contents of these pages and videos is prohibited. Furthermore, the content may neither be copied nor made available to third parties for
commercial purposes. Also subject to copyright are the images and videos that were made available to WAGO Kontakttechnik GmbH & Co. KG by third parties.”