Pass Cisco 200-125 Exam With 100% Guarantee: CCNA Cisco Certified Network Associate CCNA (v3.0)

https://www.passapply.com/200-125.
html
2020 Latest passapply 200-125 PDF and VCE dumps Download
200-125Q&As
CCNA Cisco Certified Network Associate CCNA (v3.0)
Pass Cisco 200-125 Exam with 100% Guarantee
Free Download Real Questions & Answers PDF and VCE file from:
https://www.passapply.com/200-125.html
100% Passing Guarantee

100% Money Back Assurance
Following Questions and Answers are all new published by Cisco

Official Exam Center
200-125 PDF Dumps | 200-125 Practice Test | 200-125 Study Guide 1 / 21

QUESTION 1
Which two results occur when the ipv6 enable command is entered? (Choose two)
A. An IPv6 EUI-64 interface ID is configured automatically on the interface.
B. IPv6 is enabled on a single interface.
C. An IPv6 link-local unicast address is configured automatically on the interface.
D. The administrator is prompted to configure an IP address on the interface
E. IPv6 is enabled globally on the device.
Correct Answer: BC
QUESTION 2
Which two pieces of information can you determine from the EIGRP topology table? (Choose two)
A. Route 10.42.88.0/21 has an administrative distance of 28160
B. Route 10.42.91.0/24 has a tag of 28160
C. Each route has only one best path
D. The EIGRP neighbor IP address is 10.111 253.216
E. The reported distance of 10.0.0.0/8 is 0
Correct Answer: CE
QUESTION 3
What are three values that must be the same within a sequence of packets for Netflow to consider them a network flow?
(Choose three.)
A. source IP address
B. source MAC address
C. egress interface
D. ingress interface
E. destination IP address
F. IP next-hop
Correct Answer: ADE

Each packet that is forwarded within a router or switch is examined for a set of IP packet attributes. These attributes are
the IP packet identity or fingerprint of the packet and determine if the packet is unique or similar to other packets.
Traditionally, an IP Flow is based on a set of 5 and up to 7 IP packet attributes. IP Packet attributes used by NetFlow:
?IP source address ?IP destination address ?Source port ?Destination port ?Layer 3 protocol type ?Class of Service
?Router or switch interface All packets with the same source/destination IP address, source/destination ports, protocol
interface and class of service are grouped into a flow and then packets and bytes are tallied. This methodology of
fingerprinting or determining a flow is scalable because a large amount of network information is condensed into a
database of NetFlow information called the NetFlow cache.
Reference: http://www.cisco.com/c/en/us/products/collateral/ios-nx-os-software/ios-
netflow/prod_white_paper0900aecd80406232.html
QUESTION 4
In an Ethernet network, under what two scenarios can devices transmit? (Choose two.)
A. when they receive a special token
B. when there is a carrier
C. when they detect no other devices are sending
D. when the medium is idle
E. when the server grants access
Correct Answer: CD
Ethernet network is a shared environment so all devices have the right to access to the medium. If more than one
device transmits simultaneously, the signals collide and cannot reach the destination.
If a device detects another device is sending, it will wait for a specified amount of time before attempting to transmit.
When there is no traffic detected, a device will transmit its message. While this transmission is occurring, the device
continues to listen for traffic or collisions on the LAN. After the message is sent, the device returns to its default
listening
mode.
QUESTION 5
Refer to the exhibit.

C-router is to be used as a "router-on-a-stick" to route between the VLANs. All the interfaces have been properly
configured and IP routing is operational. The hosts in the VLANs have been configured with the appropriate default
gateway. What is true about this configuration?
A. These commands need to be added to the configuration: C-router(config)# router eigrp 123 C-router(config-router)#
network 172.19.0.0
B. These commands need to be added to the configuration: C-router(config)# router ospf 1 C-router(config-router)#
network 172.19.0.0 0.0.3.255 area 0
C. These commands need to be added to the configuration: C-router(config)# router rip C-router(config-router)# network
172.19.0.0
D. No further routing configuration is required.
Correct Answer: D
Since all the same router (C-router) is the default gateway for all three VLANs, all traffic destined to a different VLA will
be sent to the C-router. The C-router will have knowledge of all three networks since they will appear as directly
connected in the routing table. Since the C-router already knows how to get to all three networks, no routing protocols
need to be configured.
QUESTION 6
Which command shows your active Telnet connections?
A. show cdp neigbors
B. show session
C. show users
D. show vty logins
Correct Answer: B
The "show users" shows telnet/ssh connections to your router while "show sessions" shows telnet/ssh connections from
your router (to other devices). The question asks about "your active Telnet connections", meaning connections from
your router so the answer should be A.

QUESTION 7
Which NTP command configures the local device as an NTP reference clock source?
A. ntp peer
B. ntp broadcast
C. ntp master
D. ntp server
Correct Answer: C
QUESTION 8
Which two options are primary responsibilities of the APlC-EM controller? (Choose two.)
A. lt automates network actions between different device types
B. lt provides robust asset management.
C. lt tracks license usage and Cisco lOS versions.
D. lt automates network actions between legacy equipment.
E. lt makes network functions programmable.
Correct Answer: AE
QUESTION 9
What can you change to select switch as root bridge?
A. make lower priority
B. make higher priority
C. make lower path cost
D. make higher path cost
Correct Answer: A
QUESTION 10
Which two statements about IPv6 multicast address are true ?(choose two)
A. If the liftime parameter is set to 1,the route is permanent.

B. They use the prefix FC80::/8
C. They use the prefix FF00::/8
D. They identify a group of interfaces on different devices
E. If the scope parameter is set to 5,the route is local to the node
Correct Answer: CD
QUESTION 11
Where does routing occur within the DoD TCP/IP reference model?
A. application
B. internet
C. network
D. transport
Correct Answer: B
The picture below shows the comparison between TCP/IP model and OSI model. Notice that the Internet Layer of
TCP/IP is equivalent to the Network Layer which is responsible for routing decision.
QUESTION 12
Which two are advantages of static routing when compared to dynamic routing? (Choose two.)
A. Configuration complexity decreases as network size increases.

B. Security increases because only the network administrator may change the routing table.
C. Route summarization is computed automatically by the router.
D. Routing tables adapt automatically to topology changes.
E. An efficient algorithm is used to build routing tables, using automatic updates.
F. Routing updates are automatically sent to neighbors.
G. Routing traffic load is reduced when used in stub network links.
Correct Answer: BG
Since static routing is a manual process, it can be argued that it is more secure (and more prone to human errors) since
the network administrator will need to make changes to the routing table directly. Also, in stub networks where there is
only a single uplink connection, the load is reduced as stub routers just need a single static default route, instead of
many routes that all have the same next hop IP address.
QUESTION 13
What will be the result if the following configuration commands are implemented on a Cisco switch? Switch(config-if)#
switchport port-security Switch(config-if)# switchport port-security mac-address sticky
A. A dynamically learned MAC address is saved in the startup-configuration file.
B. A dynamically learned MAC address is saved in the running-configuration file.
C. A dynamically learned MAC address is saved in the VLAN database.
D. Statically configured MAC addresses are saved in the startup-configuration file if frames from that address are
received.
E. Statically configured MAC addresses are saved in the running-configuration file if frames from that address are
received.
Correct Answer: B
In the interface configuration mode, the command switchport port-security mac-address sticky enables sticky learning.
When entering this command, the interface converts all the dynamic secure MAC addresses to sticky secure MAC
addresses.
QUESTION 14
Which type of topology is required by DMVPN?
A. ring
B. full mesh
C. hub-and-spoke
D. partial mesh

Correct Answer: C
QUESTION 15
The technician wants to upload a new IOS in the router while keeping the existing IOS. What is the maximum size of an
IOS file that could be loaded if the original IOS is also kept in flash?
A. 3 MB
B. 4 MB
C. 5 MB
D. 7 MB
E. 8 MB
Correct Answer: B
In this example, there are a total of 8 MB, but 3.8 are being used already, so another file as large as 4MB can be loaded
in addition to the original file.
QUESTION 16
From which PPPoE server configuration does a PPPoE client get an IP address?
A. AAA authentication
B. DHCP
C. dialer interface
D. virtual-template interface
Correct Answer: D
QUESTION 17
Which two statements about RIPv2 are true? (Choose two )

A. It must be manually enabled after RIP is configured as the routing protocol
B. It uses multicast address 224.0.0.2 to share routing information between peers
C. its default administrative distances 120
D. It is a link-state routing protocol
E. It is an EGP routing protocol
Correct Answer: AC
QUESTION 18
What occurs on a Frame Relay network when the CIR is exceeded?
A. All TCP traffic is marked discard eligible.
B. All UDP traffic is marked discard eligible and a BECN is sent.
C. All TCP traffic is marked discard eligible and a BECN is sent.
D. All traffic exceeding the CIR is marked discard eligible.
Correct Answer: D
Committed information rate (CIR): The minimum guaranteed data transfer rate agreed to by the Frame Relay switch.
Frames that are sent in excess of the CIR are marked as discard eligible (DE) which means they can be dropped if the
congestion occurs within the Frame Relay network.
Note: In the Frame Relay frame format, there is a bit called Discard eligible (DE) bit that is used to identify frames that
are first to be dropped when the CIR is exceeded.
QUESTION 19
Which three are the possible trunking modes for a switch port? (Choose three.)
A. forwarding
B. desirable
C. transparent
D. Auto
E. on
F. off
Correct Answer: BDE

QUESTION 20
What is known as "one-to-nearest" addressing in IPv6?
A. global unicast
B. anycast
C. multicast
D. unspecified address
Correct Answer: B
IPv6 Anycast addresses are used for one-to-nearest communication, meaning an Anycast address is used by a device
to send data to one specific recipient (interface) that is the closest out of a group of recipients (interfaces).
QUESTION 21
Which two of these statements are true of IPv6 address representation? (Choose two.)
A. There are four types of IPv6 addresses: unicast, multicast, anycast, and broadcast.
B. A single interface may be assigned multiple IPv6 addresses of any type.
C. Every IPv6 interface contains at least one loopback address.
D. The first 64 bits represent the dynamically created interface ID.
E. Leading zeros in an IPv6 16 bit hexadecimal field are mandatory.
Correct Answer: BC
A single interface may be assigned multiple addresses of any type (unicast, anycast, multicast). Every IPv6-enabled
interface must contain at least one loopback and one link-local address. Optionally, every interface can have multiple
unique local and global addresses.
Reference: IPv6 Addressing at a Glance ?Cisco PDF
QUESTION 22
Drag and drop the benefits of a cisco wireless Lan controller from the left onto the correct examples on the right.
Select and Place:

Correct Answer:
QUESTION 23
Which protocol is a Cisco proprietary implementation of STP?
A. CST
B. RSTP
C. MSTP
D. PVST+
Correct Answer: D
QUESTION 24

Given this output for SwitchC, what should the network administrator\\'s next action be?
A. Check the trunk encapsulation mode for SwitchC\\'s fa0/1 port.
B. Check the duplex mode for SwitchC\\'s fa0/1 port.
C. Check the duplex mode for SwitchA\\'s fa0/2 port.
D. Check the trunk encapsulation mode for SwitchA\\'s fa0/2 port.
Correct Answer: C
Here we can see that this port is configured for full duplex, so the next step would be to check the duplex setting of the
port on the other switch. A mismatched trunk encapsulation would not result in input errors and CRC errors.
QUESTION 25
Which two neighbor types are supported in a bgp environment? (Choose two)
A. remote
B. directly attached
C. external
D. autonomous

E. internal
Correct Answer: CE
QUESTION 26
Which two Cisco IOS commands, used in troubleshooting, can enable debug output to a remote location? (Choose two)
A. no logging console
B. logging host ip-address
C. terminal monitor
D. show logging | redirect flashioutput.txt
E. snmp-server enable traps syslog
Correct Answer: BC
QUESTION 27
If router R1 knows a static route to a destination network and then learn about the same destination network through a
dynamic routing protocol, how does R1 respond?
A. It sends a withdrawal notification to the neighboring router.
B. It refuses to advertise the dynamic route to other neighbors.
C. It disables the routing protocol.
D. It prefers the static route.
Correct Answer: D
QUESTION 28
Select and Place:

Correct Answer:

QUESTION 29
What value is primarily used to determine which port becomes the root port on each nonroot switch in a spanning-tree
topology?
A. path cost
B. lowest port MAC address
C. VTP revision number
D. highest port priority number
E. port priority number and MAC address
Correct Answer: A
The path cost to the root bridge is the most important value to determine which port will become the root port on each
non-root switch. In particular, the port with lowest cost to the root bridge will become root port (on non-root switch).
QUESTION 30
What is the result of setting the no login command?
A. Telnet access is denied.
B. Telnet access requires a new password at the first login.
C. Telnet access requires a new password.
D. no password is required for telnet access.
Correct Answer: D
QUESTION 31
Which two functions can be performed by a local DNS server? (Choose two)
A. transferring spirt horizon traffic between zones
B. Forwarding name resolution requests to an external DNS server

C. assigning IP addresses to local clients
D. resolving names locally
E. copying updated IOS images to Cisco switches
Correct Answer: BD
QUESTION 32
Which statement about unique local IPv6 addresses is true?
A. Summarization is not supported.
B. They require all prefixes to be unique.
C. Their global IDs are assigned sequentially.
D. They are routable to the public Internet.
Correct Answer: B
QUESTION 33
Cisco Catalyst switches CAT1 and CAT2 have a connection between them using ports FA0/13. An 802.1Q trunk is
configured between the two switches. On CAT1, VLAN 10 is chosen as native, but on CAT2 the native VLAN is not
specified.
What will happen in this scenario?
A. 802.1Q giants frames could saturate the link.
B. VLAN 10 on CAT1 and VLAN 1 on CAT2 will send untagged frames.
C. A native VLAN mismatch error message will appear.
D. VLAN 10 on CAT1 and VLAN 1 on CAT2 will send tagged frames.
Correct Answer: C
A "native VLAN mismatch" error will appear by CDP if there is a native VLAN mismatch on an 802.1Q link. "VLAN
mismatch" can cause traffic from one vlan to leak into another vlan.
QUESTION 34
Which command can you enter to determine whether serial interface 0/2/0 has been configured using HDLC
encapsulation?
A. router#show platform

B. router#show interfaces Serial 0/2/0
C. router#show ip interface s0/2/0
D. router#\show ip interface brief
Correct Answer: B
QUESTION 35
Which protocol advertises a virtual IP address to facilitate transparent failover of a Cisco routing device?
A. FHRP
B. DHCP
C. RSMLT
D. ESRP
Correct Answer: A
QUESTION 36
On which OSI layer does a VLAN operate?
A. Layer 1
B. Layer 2
C. Layer 3
D. Layer 4
Correct Answer: B
QUESTION 37
Which characteristics are representatives of a link-state routing protocol? (Choose three.)
A. provides common view of entire topology
B. exchanges routing tables with neighbors
C. calculates shortest path
D. utilizes event-triggered updates
E. utilizes frequent periodic updates
Correct Answer: ACD

Each of routers running link-state routing protocol learns paths to all the destinations in its "area" so we can say
although it is a bit unclear. Link-state routing protocols generate routing updates only (not the whole routing table) when
a change
occurs in the network topology so
Link-state routing protocol like OSPF uses Dijkstra algorithm to calculate the shortest path - >.
Unlike Distance vector routing protocol (which utilizes frequent periodic updates), link-state routing protocol utilizes
event-triggered updates (only sends update when a change occurs) ->.
QUESTION 38
After HostA pings HostB, which entry will be in the ARP cache of HostA to support this transmission?

A. Exhibit A
B. Exhibit B
C. Exhibit C
D. Exhibit D
E. Exhibit E
F. Exhibit F
Correct Answer: A
Host A knows host B is in another network so it will send the pings to its default gateway 192.168.6.1. Host A sends a
broadcast frame asking the MAC address of 192.168.6.1. This information (IP and MAC address of the default gateway)
is saved in its ARP cache for later use.
QUESTION 39
A security administrator wants to profile endpoints and gain visibility into attempted authentications. Which 802.1x mode
allows these actions?
A. Monitor mode
B. High-Security mode
C. Low-impact mode
D. Closed mode

Correct Answer: A
QUESTION 40
The output of the show frame-relay pvc command shows "PVC STATUS = INACTIVE". What does this mean?
A. The PVC is configured correctly and is operating normally, but no data packets have been detected for more than five
minutes.
B. The PVC is configured correctly, is operating normally, and is no longer actively seeking the address of the remote
router.
C. The PVC is configured correctly, is operating normally, and is waiting for interesting traffic to trigger a call to the
remote router.
D. The PVC is configured correctly on the local switch, but there is a problem on the remote end of the PVC.
E. The PVC is not configured on the local switch.
Correct Answer: D
The PVC STATUS displays the status of the PVC. The DCE device creates and sends the report to the DTE devices.
There are 4 statuses:
ACTIVE: the PVC is operational and can transmit data + INACTIVE: the connection from the local router to the switch is
working, but the connection to the remote router is not available + DELETED: the PVC is not present and no LMI
information is being received from the Frame Relay switch
STATIC: the Local Management Interface (LMI) mechanism on the interface is disabled (by using the "no keepalive"
command). This status is rarely seen so it is ignored in some books.
200-125 PDF Dumps 200-125 Practice Test 200-125 Study Guide

To Read the Whole Q&As, please purchase the Complete Version from Our website.
Try our product !
100% Guaranteed Success

100% Money Back Guarantee
365 Days Free Update
Instant Download After Purchase
24x7 Customer Support
Average 99.9% Success Rate
More than 800,000 Satisfied Customers Worldwide
Multi-Platform capabilities - Windows, Mac, Android, iPhone, iPod, iPad, Kindle
We provide exam PDF and VCE of Cisco, Microsoft, IBM, CompTIA, Oracle and other IT Certifications.
You can view Vendor list of All Certification Exams offered:
https://www.passapply.com/allproducts
Need Help
Please provide as much detail as possible so we can best assist you.
To update a previously submitted ticket:
Any charges made through this site will appear as Global Simulators Limited.
All trademarks are the property of their respective owners.
Copyright © passapply, All Rights Reserved.
Powered by TCPDF (www.tcpdf.org)

Pass Cisco 200-125 Exam With 100% Guarantee: CCNA Cisco Certified Network Associate CCNA (v3.0)

Uploaded by

Copyright:

Available Formats

Pass Cisco 200-125 Exam With 100% Guarantee: CCNA Cisco Certified Network Associate CCNA (v3.0)

Uploaded by

Document Information

Original Title

Copyright

Available Formats

Share this document

Share or Embed Document

Sharing Options

Did you find this document useful?

Is this content inappropriate?

Copyright:

Available Formats

Pass Cisco 200-125 Exam With 100% Guarantee: CCNA Cisco Certified Network Associate CCNA (v3.0)

Uploaded by

Copyright:

Available Formats

https://www.passapply.com/200-125.

Pass Cisco 200-125 Exam with 100% Guarantee

100% Passing Guarantee

Following Questions and Answers are all new published by Cisco

200-125 PDF Dumps | 200-125 Practice Test | 200-125 Study Guide 1 / 21

A. An IPv6 EUI-64 interface ID is configured automatically on the interface.

B. IPv6 is enabled on a single interface.

C. An IPv6 link-local unicast address is configured automatically on the interface.

D. The administrator is prompted to configure an IP address on the interface

E. IPv6 is enabled globally on the device.

A. Route 10.42.88.0/21 has an administrative distance of 28160

B. Route 10.42.91.0/24 has a tag of 28160

C. Each route has only one best path

D. The EIGRP neighbor IP address is 10.111 253.216

E. The reported distance of 10.0.0.0/8 is 0

B. source MAC address

Correct Answer: ADE

200-125 PDF Dumps | 200-125 Practice Test | 200-125 Study Guide 2 / 21

A. when they receive a special token

B. when there is a carrier

C. when they detect no other devices are sending

D. when the medium is idle

E. when the server grants access

Refer to the exhibit.

200-125 PDF Dumps | 200-125 Practice Test | 200-125 Study Guide 3 / 21

D. No further routing configuration is required.

Which command shows your active Telnet connections?

A. show cdp neigbors

D. show vty logins

200-125 PDF Dumps | 200-125 Practice Test | 200-125 Study Guide 4 / 21

A. lt automates network actions between different device types

B. lt provides robust asset management.

C. lt tracks license usage and Cisco lOS versions.

D. lt automates network actions between legacy equipment.

E. lt makes network functions programmable.

What can you change to select switch as root bridge?

A. make lower priority

B. make higher priority

C. make lower path cost

D. make higher path cost

A. If the liftime parameter is set to 1,the route is permanent.

200-125 PDF Dumps | 200-125 Practice Test | 200-125 Study Guide 5 / 21

B. They use the prefix FC80::/8

C. They use the prefix FF00::/8

D. They identify a group of interfaces on different devices

E. If the scope parameter is set to 5,the route is local to the node

A. Configuration complexity decreases as network size increases.

200-125 PDF Dumps | 200-125 Practice Test | 200-125 Study Guide 6 / 21

C. Route summarization is computed automatically by the router.

D. Routing tables adapt automatically to topology changes.

E. An efficient algorithm is used to build routing tables, using automatic updates.

F. Routing updates are automatically sent to neighbors.

G. Routing traffic load is reduced when used in stub network links.

A. A dynamically learned MAC address is saved in the startup-configuration file.

B. A dynamically learned MAC address is saved in the running-configuration file.

C. A dynamically learned MAC address is saved in the VLAN database.

Which type of topology is required by DMVPN?

200-125 PDF Dumps | 200-125 Practice Test | 200-125 Study Guide 7 / 21

Refer to the exhibit.