PermaRock Mineral Fibre

External Wall Insulation Systems

Overview Key Features
PermaRock Mineral Fibre external wall insulation systems provide • A2-s1,d0 reaction to fire classification (EN 13501-1:2007 +
excellent reaction to fire performance, and systems with an A2- A1:2009) - can be used on buildings of any building height*
s1,d0 classification in accordance with BS EN 13501- 1:2007 • Incorporates non-combustible mineral fibre (stonewool)
+A1:2009 are also suited for use on high rise buildings, including insulation (Euroclass A1 – BS EN 13501-1:2007 + A1:2009)
those with floor levels above 18 metres above ground level. • SWIGA approved high-rise system
• Adhesively bonded + mechanically anchored for enhanced
Mineral Fibre systems with PermaRock SiliconeUltra K 1.5mm, resistance to wind loading
Mineral K 2.0mm, Brick Slip, Brick Effect Render and Dry Dash • Wide selection of decorative renders / finishes / effects
Finishes are class A2-s1,d0* to BS EN 13501-1:2007 + A1:2009.

Typical Mineral Fibre EWI system incorporating Quick Check

through-coloured K or R Finish
Approvals BRE Global Certification
Residential, Education, Healthcare,
Substrate Market Sectors
Public Buildings, Commercial
Adhesive
Brickwork, Dense + No-Fines
Mineral Fibre Insulation Substrate Types Concrete, Blockwork, Metal Frame,
Base Coat Timber Frame
Reinforcement Building Height (limitations) No limit*
Base Coat
Decorative Render / Finishes See table overleaf
Insulation Fixing
Insulation Thermal
Primer 0.036
Conductivity (W/mK)
Decorative Finish
Reinforcement layer fixings Insulation Thicknesses 50 - 250 mm**
omitted for clarity
*Dependent on decorative finish type and detail design
**30mm board available (0.39 W/mK)

Cert No. FM13066 EMS580356

158/12
Environmental & Quality Standards
• The system is manufactured and supplied in accordance
with BS EN ISO 9001 (Quality Management) and BS EN ISO
14001 (Environmental Management)
• Mineral Fibre insulation is manufactured to EN 13162 and is
CFC and HCFC free
• The insulation has zero Ozone Depletion Potential
(zero-ODP) and zero global warming potential (GWP)
• Recycling facility for uncontaminated insulation boards
is available for site waste
• Ecopoint Rating /m² – 0.10: Excellent
• Low U-Values are achievable in order to meet or exceed
BREEAM, Passivhaus, EnerPHit and similar performance
standards, etc
• Green Guide to Specification A Rating achievable
U-values: Insulation thickness requirements to achieve a range
of U-values for typical wall constructions can be found in our
New / Existing Buildings brochures and on our website.
System Options
Insulation Fixing Reinforcement Layer(1) Intermediate Coat(s) Top (Finish) Coat Notes
PermaRock Acrylic K/R Finish
1.5 mm, 2.0 mm & 3.0
PermaRock Silicone K/R Finish mm grain size top coats
available
PermaRock SiliconeUltra K/R
PermaRock Adhesive PermaRock PermaRock K&R Finish
& PermaRock PermaRock Bedding Mortar & Bedding Mortar Primer
Mechanical Fixings PermaRock Reinforcing Mesh PermaRock Stone Chip Approx. 2 mm grain size
(e.g Masonry, Render
Dense and No-Fines or
PermaRock PermaRock Brick Slip Metric and imperial /
Concrete)
Mineral Fibre PermaRock Bedding Mortar & Adhesive & PermaRock Brick non-standard brick slip
(50 mm - 250 mm) PermaRock Armoured Mesh Slips sizes available
or
(for areas where high levels
Thermal impact resistance are 2.0 mm, 3.0 mm & 5.0
PermaRock PermaRock Bedding Mortar PermaRock Mineral K/R Finish mm grain size top coats
conductivity required)
Lamella Adhesive available
0.036 W/mK & PermaRock
Mechanical Fixings PermaRock Brick Effect Render PermaRock Brick Effect
(e.g Sheathed frame Base Layer Render Face Layer
constructions - Metal
/ Timber Frame) PermaRock Dashing
PermaRock Dashing Mortar(2) Aggregates

PermaRock Scratch Render PermaRock Silicone Scratch

Basecoat & PermaRock Render
Reinforcing Mesh

(1)
Additional reinforcement layer fixings are required for buildings over 2 storeys in height and/or for buildings in high exposure locations
(2)
PermaRock Dashing Mortar is available in a range of colours

Technical Overview
System Properties
Approvals BRE Global Certification: BRE Certificate No. 158/12.

Thermal Performance Systems can be designed to achieve U-values which satisfy or exceed current UK Building Regulation requirements.

Provides a weather resistant cladding to new and existing backing walls of brick and block masonry, dense and no-fines concrete and sheathed light
Weather Resistance gauge steel frame and timber frame constructions. Can be designed buildings in locations where the wind driven rain exposure classification is very severe.
Using a combination of adhesive bonding and mechanical fixing, these systems can be designed to withstand all anticipated wind load (suction)
Wind Loads scenarios in the UK.
Systems can achieve levels of hard body impact resistance in excess of 40J and can be designed for the zones associated with Categories I, II and III
Impact Resistance as defined in ETAG004.
Class A1 insulation (BS EN 13501-1:2007 + A1:2009). PermaRock Mineral Fibre systems with PermaRock SiliconeUltra K 1.5mm Finish, PermaRock
Mineral K 2.0mm Finish, PermaRock Brick Slips, PermaRock Brick Effect Render and PermaRock Dry Dash Finish are assessed to EN 13501-1:2007 +
Fire Performance A1:2009 and are classed A2-s1,d0 (50mm - 250mm). Class O surfaces as defined in the Building Regulations when tested to BS 476 parts 6 and 7 can
be achieved. Fire tested in accordance with BS 8414-1: 2002 - compliant with BR 135 Annex A; 2003 (Acrylic Finish).
Water Vapour The systems are water vapour permeable. The rate of permeability depends on the system (thickness and decorative finish type) selected.
Permeability
Systems can be considered to have a design working like of at least 30 years. Lifetimes significantly in excess of 30 years can be achieved with proper
Design Life maintenance and repair if damaged.

For further information on the decorative finishes above please consult the relevant information sheet, website or contact PermaRock.
All information stated is correct at time of printing and subject to change without notice.

Version 4

PermaRock Products Ltd t +44 (0)1509 262924

Jubilee Drive, Loughborough e [email protected]
Leicestershire, LE11 5TW. w www.permarock.com