MITSUMI Lithium-ion battery charge control IC MM3635

Lithium-ion battery charge control IC

Monolithic IC MM3635

Outline
This IC is a linear charge control IC for low capacity battery.
Charging from 0V of battery voltage is available, so this IC is optimum for product used low-capacity battery.
Charge control voltage can be set according to a battery to be used. (4.2 or 4.05V)

Features
1. BAT Regulation Voltage 4.2V±30mV(0.7%) / 4.05V±50mV (Setting by CVSEL pin)
2. Fast Charge Current 15mA±1.8mA RICHG=74.2k
3. Charging from 0V of battery voltage.
4. Trickle-charge current, Fast-charge current, Charge completion current can be set using external
resistors(maximum charging current is 0.7 A).
5. Battery temperature detection function is provided via a thermistor, and so the charging ON/OFF can
be controlled according to the battery temperature.
6. Chip temperature detection enables control of IC temperature rises at high-power charging. The battery
can therefore be charged with optimal charging regulation.
7. Built-in charging timer. Charging timer time can be freely set using external resistor.
8. Small package SSON-10A (2.7×2.5×0.6mm)

Package
SSON-10A

Applications
1. Cellular phones
2. Portable music players
3. Digital still cameras
4. Portable game devices

• Any products mentioned in this catalog are subject to any modification in their appearance and others for improvements without prior notification.
• The details listed here are not a guarantee of the individual products at the time of ordering. When using the products, you will be asked to check their specifications.
MITSUMI Lithium-ion battery charge control IC MM3635

Block Diagram

Input/Output
difference detection
(VCC-BAT<0.045V)
VCC BAT Li-Ion
1µF

Reset detection VREF

(2.5V)
AC Adaptor
Battery discharge
VSENSE
(5V)
(10µA,200µA,
Adaptor detection
300µA)
(3.8V) ×1/N

Charge current
detection RICHG
VCC Constant voltage control
(4.05V/4.2V) Richg
VREF 74.2k
Overvoltage
VCVREF VDD REG detection
(REG) IBAT[A]=15mA
(4.35V)

Constant current control

VCC (0.1,0.3,1C) Charge
completion
VREF detection
VDD VCCREF (0.1C)
REG
Recharge
detection
VDD Charge
(3.80V/3.95V)
(1.92V)
ON/OFF

10k
Temperature control
Fast-charge
REG start detection
Low & High 1C
temperature (3.0V)
Charge current

hys detection
hys
TH
Thermistor 0.2C
10k
(@25ºC) 0
Ttreg1 Ttreg2 Tsd
(93ºC) (103ºC) (153ºC)
Chip surface temperature

CVCEL
L : CV=4.05V
H : CV=4.20V
Charge Control
VCC
Timer short

OSC Timer short

Timer LED
(64kHz)
REG
Fosc[Hz]=
0.912V/(1.425E-10*Rosc)

Rosc
ROSC
100k

GND

• Any products mentioned in this catalog are subject to any modification in their appearance and others for improvements without prior notification.
• The details listed here are not a guarantee of the individual products at the time of ordering. When using the products, you will be asked to check their specifications.
MITSUMI Lithium-ion battery charge control IC MM3635

Pin Assignment

1
10

2 9

3 8

4 7

5 6

SSON-10A
(TOP VIEW)

1 VCC 6 TH
2 Rosc 7 CVSEL
3 LED 8 RICHG
4 GND 9 VSENSE
5 VDD 10 BAT

• Any products mentioned in this catalog are subject to any modification in their appearance and others for improvements without prior notification.
• The details listed here are not a guarantee of the individual products at the time of ordering. When using the products, you will be asked to check their specifications.
MITSUMI Lithium-ion battery charge control IC MM3635

Pin Description
Pin No. Symbol Function

1 VCC Power supply, charge Tr input pin. Connect to an AC adaptor.

Oscillation frequency setting resistance connection pin

2 Rosc fosc=0.912V/(1.425E-10×Rosc)
Estimation : The fosc value for each Rosc value is specified on the Characteristics page.

3 LED LED connect pin (Nch open drain output) Turn on during charging.

4 GND Ground pin

Battery temperature detecting reference voltage pin

It is not recommended to be used other than as battery temperature
5 VDD
detecting reference voltage (resistance connection) since it is also used for
internal charge current reference voltage.

6 TH Battery temperature detection input pin. Connect to a thermistor.

A change pin of the charge constant voltage.

7 CVSEL
L or Open : CV=4.05V, H : CV=4.20V
Charge current setting resistance connection pin
ICHG=674 ×VDD pin voltage/RICHG
8 RICHG
Estimation: The Charge Current value for each RICHG value is specified on the
Characteristics page.
Battery voltage detection, constant voltage charge control pin
9 VSENSE
Connect to the positive side of a battery pack.
Charge Tr output pin
10 BAT
Connect to the positive side of a battery pack.

Absolute Maximum Ratings

Item Symbol Ratings Units
Storage temperature TSTG −55~+150 °C
Operating temperature TOPR −40~+85 °C
Pin voltage Vin −0.3~+6.0 V
BAT pin output current IBAT 700 mA
LED pin sink current ILED 20 mA
Power dissipation Pd 1.94 ( 1) W
note : 1 When mounted on a 40 40 1.6tmm (epoxy glass, double-sided, copper layer 90%) PC board.

Recommended Operating Conditions

Item Symbol Ratings Units

Operating temperature TOPR 0~+45 °C
VCC Operating voltage Vop 4.5~5.5 V

• Any products mentioned in this catalog are subject to any modification in their appearance and others for improvements without prior notification.
• The details listed here are not a guarantee of the individual products at the time of ordering. When using the products, you will be asked to check their specifications.
MITSUMI Lithium-ion battery charge control IC MM3635

Electrical Characteristics (Except where noted otherwise Ta=0~45°C, VCC=5.0V)

Item Symbol Measurement conditions Min. Typ. Max. Units

Supply current ICC During fast charge (Irapchg = 500mA setting) 3.0 4.5 mA

Inflow current of BAT/VSENSE pin under the

following conditions :
Leak current Ileak 1 2 µA
1. BAT (=VSENSE)=3.6V AC adaptor is unconnected
2. Charging is completed

Reset detection voltage Vpor Reset mode when VCC VPOR 2.3 2.5 2.7 V
ADP detection voltage Vadp Charging stops when VCC Vadp 3.6 3.8 4.0 V
VSENSE pin discharge current 1 Idischg1 VSENSE (=BAT)=3.2V in charge error mode 10.0 20.0 µA
VSENSE pin discharge current 2 Idischg2 VSENSE (=BAT)=3.2V 100 200 300 µA
Applied to detection voltage from trickle
Fast-charge start detection voltage Vqchgon 2.9 3.0 3.1 V
charge to fast charge
Fast-charge start detection Applied to detection voltage from fast
Vqchgonhys 40 90 120 mV
voltage hysteresis charge to trickle charge
Vrechg1 CVSEL=H 3.85 3.95 4.05
Recharge detection voltage V
Vrechg2 CVSEL=L 3.70 3.80 3.90
Vchg1 CVSEL=H 4.17 4.20 4.23
BAT regulation voltage V
Vchg2 CVSEL=L 4.00 4.05 4.10
Charge stop I/O potential Charge stops when VCC−BAT Vdef1
Vdef1 5 30 65 mV
difference 1 VCC=H L
Charge stop I/O potential Charge stops when VCC−BAT Vdef2
Vdef2 5 45 65 mV
difference 2 VCC=L H
Battery overvoltage detection voltage Vov VCC= Vov+100mV 4.27 4.35 4.43 V
Forced charge current Istart RICHG=74.2k 0.3C (1.0C=Irapchg) 3.10 3.85 4.60 mA
Trickle-charge current Iprechg RICHG=74.2k 0.1C (1.0C=Irapchg) 0.75 1.00 1.25 mA
RICHG=74.2k 1.0C
Fast-charge current Irapchg 13.2 15.0 16.8 mA
BAT=3.6V
Charge completion current Ifc RICHG=74.2k BAT=Vqchgon 0.75 1.00 1.25 mA
Chip temperature detection1( 1) Ttreg1 Applied to Tj (chip temperature) 83 93 103 °C
Chip temperature detection2( 1) Ttreg2 Applied to Tj (chip temperature) 103 °C
Chip temperature detection Applied to Tj (chip temperature)
Tdtreg 5 10 15 °C
difference ( 1) Ttreg2−Ttreg1
Thermal shutdown temperature ( 1) Tsd Applied to Tj (chip temperature) 143 153 163 °C
Temperature detecting
VDD VDD pin Output Voltage 1.92 V
reference voltage
Temperature detecting
IDD VDD pin Output Current 3 mA
reference terminal current ( 1)

note : 1 The parameter is guaranteed by design.

• Any products mentioned in this catalog are subject to any modification in their appearance and others for improvements without prior notification.
• The details listed here are not a guarantee of the individual products at the time of ordering. When using the products, you will be asked to check their specifications.
MITSUMI Lithium-ion battery charge control IC MM3635

Item Symbol Measurement conditions Min. Typ. Max. Units

Charge Stop Battery Temperature VDD× VDD× VDD×
VthSL Charge stop threshold when TH pin rises(−3°C) V
Detection Voltage (Low temperature) 0.7722 0.7562 0.7397
Charge Recovery Battery Temperature VDD× VDD× VDD×
VthRL Charge recovery threshold when TH pin falls (0°C) V
Detection Voltage (Low temperature) 0.7480 0.7313 0.7142
Charge Stop Battery Temperature VDD× VDD× VDD×
VthSH Charge stop threshold when TH pin falls(45°C) V
Detection Voltage (High temperature) 0.3448 0.3296 0.3149
Charge Recovery Battery Temperature VDD× VDD× VDD×
VthRH Charge recovery threshold when TH pin rises (42°C) V
Detection Voltage (High temperature) 0.3684 0.3526 0.3372
TMRcnt pin Low-Level Input Voltage VcvselL 0.5 V
TMRcnt pin High-Level Input Voltage VcvselH 2 V
TMRcnt pin Low-Level Input Current IcvselL CVSEL=0V 1 µA
TMRcnt pin High-Level Input Current IcvselH CVSEL=5.0V 10 µA
LED Output pin Low-Level Voltage VledL Iled=10mA 0.4 V
LED Output pin Leak Current Iledleak LED=5V −1 1 µA
Series Pass Tr On Resistance Ron Io=200mA 0.38 0.60
Oscillator frequency ( 1) Foc Rosc=100k 57.6 64 70.4 kHz
VSENSE pin discharge time ( 1) Tdischg Foc=64kHz 58 64 70 ms
Foc=64kHz Vpor VCC Vadp
AC Adaptor connection Tadp 24 32 ms
Applied when VCC= Vadp detection
detection time ( 1, 2)
Tadp2 Applied when VCC= Vpor detection 32 64 96 µs
Forced charge time ( 1) Tistart Foc=64kHz 480 512 544 ms
Forced charge OFF time ( 1) Toff Foc=64kHz 115 128 141 ms
Battery voltage
Tcon Foc=64kHz 96 128 ms
detection time ( 1, 3)
Fast charge start voltage
Tqstart Foc=64kHz 96 128 ms
detection time ( 1, 3)
Charge completion current
Tifc Foc=64kHz 192 256 ms
detection time ( 1, 4)
Recharge start voltage
Trechg Foc=64kHz 192 256 ms
detection time ( 1, 4)
Trickle-charge timer ( 1) Tdchg Foc=64kHz 54 60 66 min
Fast-charge timer ( 1) Tchg Foc=64kHz 270 300 330 min
Battery overvoltage
Tov Foc=64kHz 96 128 ms
detection time ( 1,3)
Charge stop battery temperature Foc=64kHz
Tpro
detection time ( 1,3) VthSL, VTH=L H or VthSH, VTH=H L
96 128 ms
Charge recovery battery temperature Foc=64kHz
TproR
detection time ( 1,3) VthRL, VTH=H L or VthRH, VTH=L H
note : 1 The parameter is guaranteed by design.
note : 2 The detection time varies depending on the timing of detection for approximately one clock due to
the mode transition system operated when matched 4 times in 8ms.
note : 3 The detection time varies depending on the timing of detection for approximately one clock due to
the mode transition system operated when matched 4 times in 32ms.
note : 4 The detection time varies depending on the timing of detection for approximately one clock due to
the mode transition system operated when matched 4 times in 64ms.

• Any products mentioned in this catalog are subject to any modification in their appearance and others for improvements without prior notification.
• The details listed here are not a guarantee of the individual products at the time of ordering. When using the products, you will be asked to check their specifications.
MITSUMI Lithium-ion battery charge control IC MM3635

Measuring Circuit

SW10

1 VCC BAT 10
1µF 1µF
I1 V1 V10 I10
SW92 IF10

SW91
VF10
VF1 2 Rosc VSENSE 9

R2 V9 I9 1.1V(Vstart)
(100k ) or more
SW31 R8
(74.2k ) SW8
3 LED RICHG 8 VF9

I3 SW32 V3 V8

IF3
VF3 100k 4 GND CVSEL 7 I7 VF8
VCC
VF7

5 VDD TH 6
SW6
V5 SW5
VF6
IF5
10k

10k

SW setting condition
Test Circuit SW31 SW32 SW5 SW6 SW8 SW91 SW92 SW10
A
B
C
D
E
F
G

• Any products mentioned in this catalog are subject to any modification in their appearance and others for improvements without prior notification.
• The details listed here are not a guarantee of the individual products at the time of ordering. When using the products, you will be asked to check their specifications.
MITSUMI Lithium-ion battery charge control IC MM3635

Test Conditions (Except where noted otherwise Ta=0~45°C, VCC=5.0V, CVSEL=H)

Item Symbol Measurement

circuit Measuring conditions

Measure the current of I1-I10 when

Supply current 1 ICC1 A
R8=(Irapchg=500mA setting) and IF10=500mA.
1. Measure the current of I10 when VF1=0V and VF10=4.2V.
Leak current Ileak A 2. Measure the current of I10 when VF10=4.25V
(charge completion mode).
Reset detection When gradually increasing VF1 from 2.3V to 2.7V under the condition of VF9=3.2V
Vpor B
voltage and VF10=3.2V, the VF1 when I9 exceeds 100µA should be Vpor.
Adaptor detection When gradually increasing VF1 from 2.3V to 4.0V under the condition of
Vadp C
voltage VF10=3.2V, the VF1 when V3 changes from H to L should be Vadp.
VSENSE pin discharge Measure the current of I9 when VF 9=4.5V to 3.2V after being kept under the
Idischg1 B
current 1 condition of VF10=3.2V and VF9=4.5V and entering into error mode.
VSENSE pin discharge Measure the current of I9 immediate after increasing VF1 from
Idischg2 B
current 2 2.3V to 5.0V when VF9=3.2V and VF10=3.2V.
Fast-charge start When gradually increasing VF10 from 2.9V to 3.1V under the condition of
Vqchgon A
detection voltage VF10=2.5V, the VF10 when |I10| exceeds 530mA should be Vqchgon.
When gradually decreasing VF10 from 3.1V to 2.7V under the condition
Fast-charge start detection
Vqchgonhys A of VF10=3.5V, the VF10 when |I10| falls below 530mA should be
voltage hysteresis
Vqchgon2. Vqchgonhys=Vqchgon-Vqchgon2
When CVSEL=H, gradually decreasing VF10 from 4.00V to 3.80V, and
Vrechg1 when CVSEL=L, gradually decreasing VF10 from 3.90V to 3.70V after
Recharge detection
C being kept in the condition of VF10=4.25V and entering into charge
voltage Vrechg2 completion mode, the VF10 when the charging restarts (|I10|>1mA)
and V3=H to L should be Vrechg1(CVSEL=H), Vrechg2(CVSEL=L).

Vchg1 Measure the voltage of V9 in fast charge mode and when IF10=
Regulation voltage A
Vchg2 -5mA (|IF10|>Ifc). Vchg1=CVSEL=H, Vchg2=CVSEL=L

When gradually decreasing VF1 from 4.1V to 4.0V under the

Charge stop I/O potential
Vdef1 A condition of fast charge mode, VF1=4.1V, and VF10=4.0V, the V1-V10
difference 1
when the charging stops (|I10|<1mA) should be Vdef1.
When gradually increasing VF1 from 4.0V to 4.1V under the condition
Charge stop I/O
Vdef2 A of fast charge mode, VF1=4.0V, and VF10=4.0V, the V1-V10 when the
potential difference 2
charging restarts (|I10|>1mA) should be Vdef2.
When gradually increasing VF10 from 4.27V to 4.43V under the condition
Battery overvoltage
Vov C of VF10=4.25V, the VF10 when V3 becomes blinking (repeating H L,
detection voltage
charge error mode) should be Vov.
Measure the current of I10 immediately after increasing VF1
Forced charge current Istart A
from 2.3V to 5.0V when VF10=3.6V and R8=75k .

Trickle-charge current Iprechg A Measure the current of I10 when VF10=2.6V and R8=75k .

Fast-charge current Irapchg A Measure the current of I10 when VF10=3.6V and R8=75k .

When gradually increasing VF9 from 4.1V to 4.2V under the condition
Charge completion
Ifc B of VF9=3.6V and VF10=Vqchgon, the |I10| immediately before V3=L to
current
H and the charging stops (|I10|>1mA) should be Ifc.
note : 1 The parameter is guaranteed by design.

• Any products mentioned in this catalog are subject to any modification in their appearance and others for improvements without prior notification.
• The details listed here are not a guarantee of the individual products at the time of ordering. When using the products, you will be asked to check their specifications.
MITSUMI Lithium-ion battery charge control IC MM3635

Item Symbol Measurement

circuit Measuring circuit

When gradually increasing chip temperature from 83°C to 103°C

Chip temperature under the condition of fast charge mode, VF1=5V, and VF10=4V, the
Ttreg1 A
detection 1 ( 1) chip temperature when I10 drops to the value that is 1C (I10 when
chip temperature is 25°C)× 95% should be Ttreg1.
When gradually increasing chip temperature from 85°C to 120°C
Chip temperature under the condition of fast charge mode, VF1=5V, and VF10=4V,
Ttreg2 A
detection 2 ( 1) the chip temperature when I10 drops to the value that is 0.2C(I10
when chip temperature is 125°C)×105% should be Ttreg2.
Chip temperature
Tdtreg A Tdtreg=Ttreg2 -Ttreg1
detection difference ( 1)
When gradually increasing chip temperature from 143°C to 163°C under
Thermal shutdown the condition of fast charge mode, VF1=5V, and VF10=3.2V, the chip
Tsd C
temperature ( 1) temperature when V3 becomes blinking (repeating H L, charge error
mode) and the charging stops (|I10| < 1mA) should be Tsd.
Temperature detecting
VDD D Measure the voltage of V5 when VF6=1.0V and VF10=3.6V.
reference voltage
Temperature detecting reference When gradually decreasing IF5 under the condition of VF6=1.0V
IDD D
terminal current ( 1) and VF10=3.6V, the |IF5| when V5=VDD×90% should be IDD.
Charge stop battery When gradually increasing VF6 from 1.0V to 2.0V under the condition
temperature detection VthSL D of fast charge mode, VF6=1.0V, and VF10=3.6V, the VF6 when V3=L to
voltage (Low temperature) H and the charging stops (|I10|<1mA) should be VthSL.
When gradually decreasing VF6 from 2.0V to 1.0V under the condition of
Charge recovery battery
charge stop temperature detection mode, VF6=2.0V, and VF10=3.6V, the
temperature detection VthRL D
VF6 when V3=H to L and the charging restarts (|I10|>1mA) should be
voltage (Low temperature)
VthRL.
When gradually decreasing VF6 from 1.0V to 0V under the
Charge stop battery
condition of fast charge mode, VF6=1.0V, and VF10=3.6V, the VF6
temperature detection VthSH D
when V3=L to H and the charging stops(|I10|<1mA) should be
voltage (High temperature)
VthSH.
When gradually increasing VF6 from 0V to 1.0V under the
Charge recovery battery
condition of charge stop temperature detection mode, VF6=0V,
temperature detection VthRH D
and VF10=3.6V, the VF6 when V3=High to Low and the charging
voltage (High temperature)
restarts(|I10|>1mA) should be VthRH.
CVSEL pin Low-level
VcvselL Measurement conditions are as Vchg, more than voltage of VF7
input voltage
C from which the voltage of V9 is set to Vchg1 is set to VcvselH,
CVSEL pin High-level
VcvselH and below voltage used as Vchg2 is set to VcvselL.
input voltage
CVSEL pin Low-level Measure the current of I7 under the condition of fast charge
IcvselL A
input current mode, VF7=0V, and VF10=3.6V.
CVSEL pin High-level Measure the current of I7 under the condition of fast charge
IcvselH A
input current mode, VF7=5V, and VF10=3.6V.
LED output pin Low- Measure the voltage of V3 under the condition of fast charge mode,
VledL A
level voltage IF3=10mA, and VF10=3.6V.
LED output pin leak Measure the current of I3 when VF3=5V and VF10=4.25V (charge
Iledleak E
current completion mode).
Measure the voltage of V1-V10 under the condition of fast charge
Series pass Tr On
Ron A mode, VF1=4.0V, and IF10= -200mA.
resistance
Ron=(V1-V10)/200mA

note : 1 The parameter is guaranteed by design.

• Any products mentioned in this catalog are subject to any modification in their appearance and others for improvements without prior notification.
• The details listed here are not a guarantee of the individual products at the time of ordering. When using the products, you will be asked to check their specifications.
MITSUMI Lithium-ion battery charge control IC MM3635

Item Symbol Measurement

circuit Measuring circuit

When increasing VF1 from 2.3V to 5.0V under the condition of VF9=3.6V
VSENSE pin discharge
Tdischg B and VF10=3.6V, measure the time from when VF1>2.5V(Vpor) to when
time ( 1)
the current of I9 drops below 100µA.
1. After being kept for 128ms and more(more than Tpro) under the
condition of VF10=3.6V and VF1=2.3V to 3.6V, measure the time
from when VF1>3.8V(Vadp) to when V3=High to Low when
Tadp C increasing VF1 from 3.6V to 5.0V.
AC Adaptor connection 2. When decreasing VF10 from 5.0V to 3.6V under the condition of fast
detection time ( 1) charge mode and VF10=3.2V, measure the time from when
VF1<3.8V(Vadp) to when the fast charge stops(|I10|<1mA).
When decreasing VF1 from 5.0V to 2.0V in fast charge mode and
Tadp2 C when VF10=3.6V, measure the time from when VF1<2.5V(Vpor) to
when V3=Low to High.
When increasing VF1 from 2.3V to 5.0V under the condition of
Forced charge time
Tistart C VF10=3.6V, measure the time from forced charge start(|I10|>1mA) to
(*1)
forced charge stop(|I10|<1mA).
After increasing VF1 from 2.3V to 5.0V under the condition of
Forced charge OFF
Toff C VF10=3.6V, the half time from forced charge stop(|I10|<1mA) to
time (*1)
fast charge start(|I10|>1mA) should be Toff.
When decreasing VF10 from 4.25V to 3.8V after charge complete
Battery voltage mode under the condition of VF10=4.25V, the half time from when
Tcon C
detection time (*1) the current of I9 exceeds 100µA to when V3=Low to High and the
charging restarts(|I10|>1mA) should be Tcon.
Fast charge start When R8=75k , after increasing VF1 from 2.3V to 5.0V under the
voltage detection time Tqstart C condition of VF10=3.2V, the half time from forced charge stop
(*1) (|I10|<1mA) to fast charge start (|I10|>1mA) should be Tqstart.
When decreasing IF10 from-80mA to -30mA under the condition
Charge completion current
Tifc F of fast charge mode and R8=75k , measure the time from when
detection time (*1)
IF10>-56mA(Ifc) to when the charging stops (I10>-1mA).
When decreasing VF10 from 4.25V to 3.8V after charge completion
Recharge start voltage
Trechg C mode under the condition of VF10=4.25V, measure the time from
detection time (*1)
when VF10<3.97V(Vrechg) to when the current of I9 exceeds 100µA.
When decreasing VF7 from 5.0V to 0V under the condition of trickle
charge mode, VF7=5.0V, VF10=2.6V, measure the time from when
Trickle-charge timer (*1) Tdchg C
VF10<0.5V(Vtmr) to when V3 starts blinking (V3=H to L, charge error
mode) and the charging stops (|I10|<1mA).
When decreasing VF7 from 5.0V to 0V under the condition of fast charge
mode, VF7=5.0V, VF10=3.6V, measure Tchg2 that is the time from when
Fast-charge timer (*1) Tchg C
VF10<0.5V(Vtmr) to when V3 starts blinking (V3= H to L, charge error
mode) and the charging stops (|I10|<1mA).
When increasing VF10 from 3.6V to 4.5V under the ondition of fast charge
Battery overvoltage
Tov C mode and VF10=3.6V, measure the time from when VF10>4.35V(Vov) to
detection time (*1)
when V3 starts blinking (V3 = H to L, charge error mode).
When increasing(decreasing) VF6 from 1.0V to 2.0V(0V) under the
Charge stop battery
condition of fast charge mode, VF6=1.0V, and VF10=3.6V, measure
temperature detection Tpro C
the time from when VF6>Vth1(VF6<Vth5) to when V3=L to H and
time (*1)
the charging stops(|I10|<1mA).
When decreasing (increasing) VF6 from 2.0V(0V) to 1.0V under
Charge recovery battery
the condition of charge stop detection mode, VF6=2.0V(0V), and
temperature detection Tpro C
VF10=3.6V, measure the time from when VF6<Vth1R(VF6>Vth5R)
time (*1)
to when V3=H to L and the charging restarts (|I10|>1mA).
note : 1 The parameter is guaranteed by design.

• Any products mentioned in this catalog are subject to any modification in their appearance and others for improvements without prior notification.
• The details listed here are not a guarantee of the individual products at the time of ordering. When using the products, you will be asked to check their specifications.
MITSUMI Lithium-ion battery charge control IC MM3635

Timing Chart ( All typ. numeric value)

Normal charge

5V
Adaptor 3.8V
Voltage Adaptor detection VCC >Vadp(3.8V)
2.5V
Vcc Reset detection VCC >Vpor (2.5V)

0V

recharge
charge start charge completion charge stop(reset)

4.2V
3.97V

3.0V
Battery
Voltage
BAT

Forced
charge CC charge2
CC charge1 CC charge2(fast-charge) CV charge charge completion (recharge)
Tistart (pre-charge)
512ms Vo=4.20V charge stop

Tifc Trechg
256ms 256ms
Tcon
128ms
1.0C
Tdischg
64ms Toff Tqstart Tqstart Toff Tcon Toff
Tadp 128ms 128ms 128ms 128ms 128ms 128ms
32ms
Charge
Tpro Tdischg Chip temperature detection Tdischg Tdischg
Current 128ms 64ms (Tjmax<93~103°C) 64ms 64ms
0.3C

0.1C

300µA
VSENSE
Discharge 200µA
(Idischg2)
Current 1µA
(Ileak)
0

ON
ON OFF ON
LED
OFF

ON
Pre charge
timer
(60min)
OFF

ON
Fast charge
timer
(300min)
OFF

• Any products mentioned in this catalog are subject to any modification in their appearance and others for improvements without prior notification.
• The details listed here are not a guarantee of the individual products at the time of ordering. When using the products, you will be asked to check their specifications.
MITSUMI Lithium-ion battery charge control IC MM3635

Input Adaptor Release Adaptor

3.8V 3.8V
VCC
2.5V VCC 2.5V
0V 0V

BAT 3.6V BAT 3.6V

1.0C 1.0C
Charge 512ms Charge 32ms
128ms (Tadp)
Current (Tistart) (Tqstart) Current
0.3C
0A 0A
32ms 128ms
(Tadp) (Toff)
300µA
300µA
200µA 128ms VSENSE
VSENSE (Idischg2) (Tpro) 64ms Discharge
Discharge 1µA 1µA
(Ileak) (Tdischg) Current (Ileak)
Current 0µA 0µA
64ms
(Tdischg) 64µs
(Tadp2)
ON ON

LED LED ON OFF

OFF OFF ON
OFF

0V<BAT<3.0V, Charge start (trickle charge) Trickle charge timeup

5.0V 5V

VCC VCC

0V 0V
BAT 2.5V
[Forced charge] [Trickle charge] BAT<3.0V
1.0C BAT
32ms BAT>1.1V
Charge (Tadp) 512ms 128ms
(Tistart) (Tqstart)
Current 0.3C [Trickle charge] [charge stop]
1.0C
0.1C Charge 60min.(Tdchg) charge error mode
0A Current
128ms 128ms 0.1C
(Tpro) (Toff) 0A
300µA
VSENSE
200µA 300µA
Discharge (Idischg2) VSENSE
64ms 10µA
Current 1µA (Tdischg) Discharge (Idischg1)
(Ileak) Current
0µA 1µA(Ileak)
64ms 0µA
(Tdischg)

ON
ON
LED ON OFF
OFF
OFF ON LED
OFF

3.0V<BAT<4.2V, Charge start (fast charge) Fast charge timeup

5V 5V
VCC
VCC 0V
BAT<4.2V
0V BAT BAT>3.0V
Timer Start
BAT 3.6V [Fast charge] [charge stop]
1.0C charge error mode
[Forced charge] [Fast charge] Charge 300min.(Tchg)
1.0C 32ms Current
Charge 0.1C
(Tadp) 512ms 128ms 0A
Current 0.3C
(Tistart) (Tqstart)
VSENSE 300µA
0A Discharge 10µA
128ms 128ms (Idischg1)
(Tpro) (Toff) Current 0µA
1µA(Ileak)
300µA
VSENSE
200µA
Discharge (Idischg2) 64ms ON
Current 1µA (Tdischg) ON OFF
(Ileak) LED
0µA OFF
64ms
(Tdischg)

ON
LED OFF ON
OFF

• Any products mentioned in this catalog are subject to any modification in their appearance and others for improvements without prior notification.
• The details listed here are not a guarantee of the individual products at the time of ordering. When using the products, you will be asked to check their specifications.
MITSUMI Lithium-ion battery charge control IC MM3635

BAT=4.2V, Charge start (charge completion) BAT>4.35V, Charge start (battery overvoltage)
5V 5V
VCC VCC

0V
0V
BAT 4.2V
[Forced charge] [charge stop]
BAT 4.4V
1.0C 32ms [charge stop]
Charge
Charge (Tadp) 512ms 128ms 256ms 128ms completion 1.0C 32ms
(Tistart) (Tqstart) (Tifc) (Tqstart) mode charge error mode
Current 0.3C Charge (Tadp)
0.1C Current 128ms
0A (Tpro)
128ms 128ms 128ms 0.1C
300µA (Tpro) (Toff) (Toff) 0A
VSENSE 200µA 128ms
Discharge (Idischg2) 300µA (Tov)
1µA VSENSE 200µA
Current (Ileak) (Idischg2)
0µA
64ms
Discharge 10µA
64ms 64ms (Idischg1)
(Tdischg) (Tdischg) (Tdischg) Current 1µA(Ileak)
0µA
ON 64ms
(Tdischg)
LED OFF ON OFF
OFF
LED OFF
OFF

Full charge detection Recharge detection

VCC 5.0V VCC 5.0V

0V 0V

BAT 3.95V
4.2V BAT

[Fast charge] [charge completion]

[Full charge] [Fast charge]
1.0C
0.1C 128ms
Charge (Tqstart) Charge 256ms 128ms 128ms
(Toff) (Tcon)
Current 256ms Current (Trechg)
0A (Tifc)
128ms 0A
(Toff)
300µA 300µA
VSENSE VSENSE 200µA
200µA
Discharge (Idischg2) 64ms Discharge (Idischg2)
64ms
Current 1µA (Tdischg) Current 1µA (Tdischg)
(Ileak) (Ileak)
0µA 0µA

ON ON
LED ON OFF LED OFF ON
OFF OFF

Fast-charge start voltage detection Chip temperature detection

5.0V 5.0V
VCC VCC
0V
0V

BAT BAT BAT>3.0V

3.0V
[Fast charge]
1.0C
[Trickle charge] [Fast charge] Chip temperature detection
1.0C Charge (charge current is controlled
Charge 128ms Current to become Tjmax=93~103˚C)
Current (Tqstart) 0.1C
0A
0.1C
0A 300µA
VSENSE
Discharge 10µA
300µA (Idischg1)
VSENSE 200µA Current 1µA(Ileak)
Discharge (Idischg2) 0µA
1µA 103˚C
Current (Ileak) 93˚C
0µA Chip
Temperature
ON
ON
LED ON
LED ON
OFF OFF

• Any products mentioned in this catalog are subject to any modification in their appearance and others for improvements without prior notification.
• The details listed here are not a guarantee of the individual products at the time of ordering. When using the products, you will be asked to check their specifications.
MITSUMI Lithium-ion battery charge control IC MM3635

Thermal shutdown Battery temperature detection

5V 5V
VCC VCC
0V
0V
BAT BAT 3.0V<BAT<4.2V
BAT>3.0V
[Fast charge] [Fast charge] [Fast charge]
[Fast charge] 1.0C
1.0C
Charge 128ms 128ms 128ms 128ms
(Tpro) (Tpro) (Tpro) (Tpro)
Charge Current
Current 0.2C
0A 0A
VSENSE 300µA
300µA 10µA
VSENSE Discharge (Idischg1)
10µA
Discharge (Idischg1) Current 1µA(Ileak)
1µA(Ileak) 0µA
Current 0µA
45˚C
(VDD 0.3296)
153˚C Battery 42˚C
Chip Temperature
(VDD 0.3526)
0˚C
Temperature 103˚C (VDD 0.7313)
93˚C (TH pin) -3˚C
(VDD 0.7562)

ON ON
LED ON OFF LED ON ON ON
OFF OFF

• Any products mentioned in this catalog are subject to any modification in their appearance and others for improvements without prior notification.
• The details listed here are not a guarantee of the individual products at the time of ordering. When using the products, you will be asked to check their specifications.
MITSUMI Lithium-ion battery charge control IC MM3635

Flow Chart

AC adaptor *1 All typ. numeric value.

connection
*2 Charge current, charge completion current and
each detection time for RICHG=74.2k , ROSC=100k ,
Reset release
CVSEL=H.
Reset No V CC Vpor(2.5V)
LED : OFF Adaptor detection time
Tadp2(64us)

Yes

V SENSE pin discharge

Idischg2(200µA)
Tdischg(64ms)

Adaptor connection detection No

VCC Vadp(3.8V)
Adaptor detection time
Tadp(32ms)

Yes

Charge start
LED : Lighting

Forced Charge ON
Istart (0.3C)/Vchg(4.2V)
/Tistart(512ms)

Forced Charge OFF

Toff(128ms)
VSENSE pin discharge
Idischg2(200µA)/Tdischg(64ms)

Battery voltage detection

Yes
VBAT Vqchgon(3.0V)
Detection time : Tqstart(128ms)

No

Trickle Charge mode Fast-Charge mode

Iprechg(0.1C)/Vchg1(4.2V) Irapchg(1.0C)/Vchg1(4.2V)
Tdchg(60min)TART Tchg(300min)TART

Yes Tdchg(60min) Yes Tchg(300min)

Timeout Timeout
No No

Battery voltage detection No Charge current detection No No Recharge voltage detection

VBAT 3.0V Ichg Ifc(0.1C) VBAT Vrechg(3.97V)
Detection time : Tqstart(128ms) Detection time : Tqstart(128ms) Detection time : Trechg(256ms)

Yes Yes Yes

Tdchg(60min) timer Charge OFF Charge OFF

Reset Toff(128ms) Toff(128ms)
VSENSE pin discharge VSENSE pin discharge
Idischg2(200µA)/Tdischg(64ms) Idischg2(200µA)/Tdischg(64ms)

Battery voltage check Battery voltage check

Charge Error Detection time : Tqstart(128ms) Detection time : Tqstart(128ms)
Charge OFF
LED : OFF
VSENSE pin discharge
Idischg1(10µA) Charge completion Charge completion flag clear
LED : OFF LED : Lighting

Timer reset
Error reset Re-Charge
Tchg(300min) timer
Reset LED : Lighting
AC adaptor
Pull out

• Any products mentioned in this catalog are subject to any modification in their appearance and others for improvements without prior notification.
• The details listed here are not a guarantee of the individual products at the time of ordering. When using the products, you will be asked to check their specifications.
MITSUMI Lithium-ion battery charge control IC MM3635

Protection function (Always detected)

*1 All typ. numeric value.

*2 Charge current, charge completion current and
each detection time for RICHG=74.2k , ROSC=100k ,
After reset release CVSEL=H.
Always works

Reset detection Over charge detection

VCC Vpor(2.5V) No
VBAT Vov(4.35V)
No Chip temperature detection No
Adaptor detection time Detection time : Tov(128ms) Tj Tsd(153˚C)
Tadp2(64us)

Yes Yes Yes

Reset
LED : OFF Charge Error
Charge OFF
LED : OFF
VSENSE pin discharge
Idischg1(10µA)

After adaptor connection

Always works

Charge stop
battery temperature detection No
VthSH(45˚C) VTH VthSL(-3˚C)
Detection time :
Tpro(128ms)
Yes

Charge stop
temperature ditection
Charge stop
LED : OFF

Timer interruption
Stop VSENSE pin discharge

Charge recovery
battery temperature detection No
VthRH(42˚C) VTH VthRL(0˚C)
Detection time :
Tpro(128ms)
Yes

• Any products mentioned in this catalog are subject to any modification in their appearance and others for improvements without prior notification.
• The details listed here are not a guarantee of the individual products at the time of ordering. When using the products, you will be asked to check their specifications.
MITSUMI Lithium-ion battery charge control IC MM3635

Characteristics (Except where noted otherwise VCC=5.0V, RICHG=74.2k , ROSC=100k , CVSEL=H, Ta=25°C)

Charge current - BAT voltage RICHG voltage - Charge current

20 2
18 1.8
Charge current (mA)

16 1.6

RICHG voltage (V)

14 1.4
12 1.2
10 1
8 0.8
6 0.6
4 0.4
2 0.2
0 0
0 1 2 3 4 5 0 2 4 6 8 10 12 14 16 18 20
BAT voltage (V) Charge current (mA)

Supply current - VCC VSENSE current - VCC

2 1.4
VSENSE current (µA) 1.2
Supply current (mA)

1.6
1.0

1.2 0.8
0.6
0.8 0.4
0.2
0.4
0.0
0 −0.2
0 1 2 3 4 5 0 1 2 3 4 5
VCC (V) VCC (V)

Charge current - RICHG external resistor Foc - ROSC external resistor

1000 120

100
Charge current (mA)

800
80
Foc (kHz)

600
60
400
40
200 20

0 0
0 10 20 30 40 50 60 70 80 90 100 0 100 1000
RICHG external resistor (k ) ROSC external resistor (k )

Note : These are typical characteristics.

• Any products mentioned in this catalog are subject to any modification in their appearance and others for improvements without prior notification.
• The details listed here are not a guarantee of the individual products at the time of ordering. When using the products, you will be asked to check their specifications.
MITSUMI Lithium-ion battery charge control IC MM3635

Line regulation Load regulation

4.23 4.23
BAT Regulation voltage (V)

BAT Regulation voltage (V)

4.22 4.22

4.21 4.21

4.20 4.20

4.19 4.19

4.18 4.18

4.17 4.17
4.5 4.6 4.7 4.8 4.9 5.0 5.1 5.2 5.3 5.4 5.5 0.1 0.2 0.3 0.4 0.5 0.6 0.7
VCC (V) Charge current (A)

Chip temperature control · Thermal shutdown Series pass Tr on resistance - Charge current
1.2 0.6

Series pass Tr on resistance ( )

1 0.5
Charge current (C)

0.8 0.4

0.6 0.3

0.4 0.2

0.2 0.1

0 0.0
20 40 60 80 100 120 140 160 0 0.2 0.4 0.6 0.8 1
Environmental temperature (°C) Charge current (A)

note : These are typical characteristics.

• Any products mentioned in this catalog are subject to any modification in their appearance and others for improvements without prior notification.
• The details listed here are not a guarantee of the individual products at the time of ordering. When using the products, you will be asked to check their specifications.
MITSUMI Lithium-ion battery charge control IC MM3635

Supply current Leak current 1-1

5.0 2
Supply current 1 (mA)

Leak current 1-1 (µA)

4.0
1

3.0
0
2.0
−1
1.0

0.0 −2
−40 −20 0 20 40 60 80 −40 −20 0 20 40 60 80
Temperature (°C) Temperature (°C)

Leak current 1-2 Reset detection voltage

2.0 2.8

Reset detection voltage (V)

2.7
Leak current 1-2 (µA)

1.5
2.6

1.0 2.5

2.4
0.5
2.3

0.0 2.2
−40 −20 0 20 40 60 80 −40 −20 0 20 40 60 80
Temperature (°C) Temperature (°C)

Adaptor detection voltage

4.1
Adaptor detection voltage (V)

4.0

3.9

3.8

3.7

3.6

3.5
−40 −20 0 20 40 60 80
Temperature (°C)

Note : These are typical characteristics.

• Any products mentioned in this catalog are subject to any modification in their appearance and others for improvements without prior notification.
• The details listed here are not a guarantee of the individual products at the time of ordering. When using the products, you will be asked to check their specifications.
MITSUMI Lithium-ion battery charge control IC MM3635

VSENSE pin discharge current 1 VSENSE pin discharge current 2

25 350
VSENSE pin discharge current 1 (µA)

VSENSE pin discharge current 2 (µA)

20 300

250
15
200
10
150
5 100

0 50
−40 −20 0 20 40 60 80 −40 −20 0 20 40 60 80
Temperature (°C) Temperature (°C)

Fast-charge start detection voltage Fast-charge start detection voltage hysteresis

3.2 160
Fast-charge start detection voltage (V)

Fast-charge start detection

voltage hysteresis (mV)
3.1 120

3.0 80

2.9 40

2.8 0
−40 −20 0 20 40 60 80 −40 −20 0 20 40 60 80
Temperature (°C) Temperature (°C)

Recharge detection voltage BAT regulation voltage

4.10 4.26
Recharge detection voltage (V)

BAT regulation voltage (V)

4.05 4.24

4.00 4.22

3.95 4.20

3.90 4.18

3.85 4.16

3.80 4.14
−40 −20 0 20 40 60 80 −40 −20 0 20 40 60 80
Temperature (°C) Temperature (°C)

Note : These are typical characteristics.

• Any products mentioned in this catalog are subject to any modification in their appearance and others for improvements without prior notification.
• The details listed here are not a guarantee of the individual products at the time of ordering. When using the products, you will be asked to check their specifications.
MITSUMI Lithium-ion battery charge control IC MM3635

Charge stop I/O potential difference 1 Charge stop I/O potential difference 2
70 70
Charge stop I/O potential

Charge stop I/O potential

60 60
difference 1 (mV)

difference 2 (mV)
50 50
40 40
30 30
20 20
10 10
0 0
−40 −20 0 20 40 60 80 −40 −20 0 20 40 60 80
Temperature (°C) Temperature (°C)

Battery overvoltage detection voltage Forced charge current

3.90 5.0
Battery overvoltage detection

Forced charge current (mA)

3.85 4.5
voltage (V)

3.80 4.0

3.75 3.5

3.70 3.0
−40 −20 0 20 40 60 80 −40 −20 0 20 40 60 80
Temperature (°C) Temperature (°C)

Trickle charge current Fast-charge current

1.4 17
Trickle-charge current (mA)

Fast-charge current (mA)

1.2 16

1.0 15

0.8 14

0.6 13
−40 −20 0 20 40 60 80 −40 −20 0 20 40 60 80
Temperature (°C) Temperature (°C)

Note : These are typical characteristics.

• Any products mentioned in this catalog are subject to any modification in their appearance and others for improvements without prior notification.
• The details listed here are not a guarantee of the individual products at the time of ordering. When using the products, you will be asked to check their specifications.
MITSUMI Lithium-ion battery charge control IC MM3635

Charge completion current Temperature detecting reference voltage

1.4 2.00

Temperature detecting reference

Charge completion current (mA)

1.2 1.95

voltage (V)
1.0 1.90

0.8 1.85

0.6 1.80
−40 −20 0 20 40 60 80 −40 −20 0 20 40 60 80
Temperature (°C) Temperature (°C)

Charge stop Batt. temperature detection voltage Charge recovery Batt. temperature detection voltage
(Low temperature) (Low temperature)
0.78 0.75
Charge stop batt.Temperature detection

Charge recovery batt.Temperature

detection voltage VDD * Vth RL (V)
0.77
voltage VDD * Vth SL (V)

0.74

0.76
0.73
0.75
0.72
0.74

0.73 0.71
−40 −20 0 20 40 60 80 −40 −20 0 20 40 60 80
Temperature (°C) Temperature (°C)

Charge stop Batt. temperature detection voltage Charge recovery Batt. temperature detection voltage
(High temperature) (High temperature)
0.35 0.37
Charge stop batt.Temperature detection

detection voltage VDD * Vth RH (V)

Charge recovery batt.Temperature
voltage VDD * Vth SH (V)

0.34 0.36

0.33 0.35

0.32 0.34

0.31 0.33
−40 −20 0 20 40 60 80 −40 −20 0 20 40 60 80
Temperature (°C) Temperature (°C)

Note : These are typical characteristics.

• Any products mentioned in this catalog are subject to any modification in their appearance and others for improvements without prior notification.
• The details listed here are not a guarantee of the individual products at the time of ordering. When using the products, you will be asked to check their specifications.
MITSUMI Lithium-ion battery charge control IC MM3635

CVSEL pin Low-level input current CVSEL pin High-level input current
1.0 10.0

CVSEL pin High-level input

CVSEL pin Low-level input

8.0
0.5

current (µA)
current (µA)

6.0
0.0
4.0
−0.5
2.0

−1.0 0.0
−40 −20 0 20 40 60 80 −40 −20 0 20 40 60 80
Temperature (°C) Temperature (°C)

LED output pin Low-level voltage LED output pin leak current
0.7 2.0
LED output pin L-level voltage (V)

LED output pin leak current (µA)

0.6
1.0

0.5
0.0
0.4
−1.0
0.3

0.2 −2.0
−40 −20 0 20 40 60 80 −40 −20 0 20 40 60 80
Temperature (°C) Temperature (°C)

Series pass Tr on resistance LED blinking cycle

0.6 1.3
Series pass Tr on resistance ( )

LED blinking cycle (s)

0.5 1.2

0.4 1.1

0.3 1.0

0.2 0.9

0.1 0.8
−40 −20 0 20 40 60 80 −40 −20 0 20 40 60 80
Temperature (°C) Temperature (°C)

Note : These are typical characteristics.

• Any products mentioned in this catalog are subject to any modification in their appearance and others for improvements without prior notification.
• The details listed here are not a guarantee of the individual products at the time of ordering. When using the products, you will be asked to check their specifications.
MITSUMI Lithium-ion battery charge control IC MM3635

VSENSE pin discharge time Forced charge time

80 620
VSENSE discharge time (ms)

Forced charge time (ms)

75 580
70
540
65
500
60

55 460

50 420
−40 −20 0 20 40 60 80 −40 −20 0 20 40 60 80
Temperature (°C) Temperature (°C)

Forced charge OFF time Trickle-charge timer

160 75

Trickle-charge OFF timer (ms)

Forced charge OFF time (ms)

150 70

140 65

130 60

120 55

110 50

100 45
−40 −20 0 20 40 60 80 −40 −20 0 20 40 60 80
Temperature (°C) Temperature (°C)

Fast-charge timer
340
Fast-charge timer (ms)

320

300

280

260

240
−40 −20 0 20 40 60 80
Temperature (°C)

Note : These are typical characteristics.

• Any products mentioned in this catalog are subject to any modification in their appearance and others for improvements without prior notification.
• The details listed here are not a guarantee of the individual products at the time of ordering. When using the products, you will be asked to check their specifications.
MITSUMI Lithium-ion battery charge control IC MM3635

Application Circuit
AC
ADAPTOR
Li-ion
VDC VCC[1] BAT[10] Battery
Cin Rosc COUT
1µF Rosc[2] VSENSE[9] 1µF
100k
Protection IC SYSTEM
RICHG[8] INTERFACE
GND RICHG
MM3635 74.2k
SYSTEM
6V or lower
470k LED[3] VDD[5]
10k SYSTEM
CVSEL INTERFACE
[7] GND[4] TH[6]
Thermistor
Input Overvoltage Protection
Load Switch 10k
(@25ºC)
B value
;3380K

· We shall not be liable for any trouble or damage caused by using this circuit.
· In the event a problem which may affect industrial property or any other rights of us or a third party is
encountered during the use of information described in these circuit, Mitsumi Electric Co., Ltd. shall not be
liable for any such problem, nor grant.

• Any products mentioned in this catalog are subject to any modification in their appearance and others for improvements without prior notification.
• The details listed here are not a guarantee of the individual products at the time of ordering. When using the products, you will be asked to check their specifications.