PATROL-USM combined FEATURES ALGORITHM 3.

To activate the alarm, both

PATROL™- USM ultrasonic & microwave
· UNPRECEDENTED PREMISES Dual-technology detector
ultrasonic and microwave
signals must be successively
detector determines PROTECTION incorporates two physical sensed within a pre-
destruction of walls, doors,
· STABLE OPERATION IN A WIDE- means for determining determined time period.
COMBINED all types of glass and intrusion
RANGING TEMPERATURE destruction of walls, doors,
ULTRASONIC & MW into the protected area.
ENVIRONMENT all types of glass and intrusion
Figure 1
INTRUSION DETECTOR into the protected area:
PATROL-USM with anti-mask · INNOVATIVE METHOD FOR Human Motion Detection
DETECTING ULTRASONIC AND registering the change in
technology detects any of the
MW SIGNALS frequency of ultrasonic and
DETECTS BREAKAGE, ultrasonic sensors' masking
microwave signals
INTRUSION AND MOTION attempts. · DIGITAL SPECTRAL ANALYSIS (Doppler Effect).
WITHIN PROTECTED AREA OF ULTRASONIC AND MW
FREQUENCIES
1. The Doppler Effect occurs
· PULSE-COUNT SELECTION (1-5) when ultrasonic waves, emitted
INSTRUCTION continuously by the detector,
MANUALS · SEPARATE ADJUSTMENT
change their length and
FOR BOTH ULTRASONIC AND
MW CHANNEL SENSITIVITY frequency when reflecting from
different moving objects.
· BUILT- IN ANTI- MASK SYSTEM
2. The Doppler Effect occurs
· HIGH RFI/EMI PROTECTION
when microwaves, emitted by
· TAMPER PROTECTION the detector, change their
length and frequency when
· AUTOMATIC GAIN CONTROL –
ADAPTATION TO
reflecting from different moving
ENVIRONMENTAL CHANGES objects.

1 2 3 4 5

Figure 2 Figure 3 For wiring, use the INSTALLATION DETECTOR

Wall Breakage Detection Glass Breakage Detection designated opening above LIMITATIONS INSTALLATION OPTIONS
the detector terminal block.
· Do not install the detector
2. Connect the wires in on unstable or vibrating
accordance with the scheme. surfaces.
· Do not install the detector
+ 12V - RELAY TAMPER
close to curtains, blinds or
other items that vibrate with
air movement.
· Do not install the detector
NOTE! close to air conditioners, air
blast sources or above heat
Several detectors of this type
sources.
DETECTOR can be installed within the
INSTALLATION protected area, at a distance · Do not install the detector
of at least 3 meters from each or route power wires and
1. Fix the detector vertically other. alarm loops next to high
on solid, flat wall surface. voltage cables
The installation height is
· Do not install the detector
2 – 2.5 meters.
near bells, sirens or
For corner installation, use electronic sounders within
knockouts located on the the premises where sound-
sloping part of the detector pressure level exceeds
base. 75dB.
6 7 8 9 10
DETECTOR TESTING If needed, increase the 5. Test the microwave (MW) 6. Replace jumper W2 to 8. Replace the cover - red
AND ADJUSTMENT detector ultrasonic channel channel operation. "WORK" position. LED will blink. At the same
sensitivity using W4 jumper · Set jumper W2 to "MW time, keep the detector field-
1. Remove the front cover. 7. Select the required number
(Ultrasonic Sensitivity). TEST" position. of-view clear, until the LED
of pulses (1-5).
2. Set jumper W2 to "US stops blinking – the anti-
· Stay for a while to make · Walk into the detector masking function will then
TEST" position. Selectable pulse count 1, 2, 3,
sure the green LED stops field-of-view. The yellow LED be correctly activated.
4 or 5 provides users with the
3. Connect the power. blinking, which means the should actively respond to your option of optimizing detector
detector ultrasonic channel movement. If necessary,
4. Test the ultrasonic channel sensitivity to suit the
is configured correctly! increase the detector
operation. environment, thus retaining
If the green LED keeps blinking, microwave channel sensitivity, reliable performance at all
check the premises without using R11 potentiometer
· First of all, make sure there times.
interferences, as described (Microwave Sensitivity).
are no humans or animals
above. To adjust pulse count for
within the protected area, · Stay for a while to make sure
windows are closed; specific operating
If necessary, reduce the the yellow LED stops blinking,
air-conditioners, fans and environments:
excessive ultrasonic channel which means the detector
other possible sources of sensitivity using W4 jumper microwave (MW) channel is A. Remove the W3 jumper.
air flow are switched off. (Ultrasonic Sensitivity). configured correctly! If the The red LED blinks, indicating
yellow LED keeps blinking, that pulse counting has begun.
· Walk into the detector
field-of-view. The green LED reduce the excessive MW B. Replace jumper W3 during
should actively respond to channel sensitivity using pause between LED blinking.
your movement. the R11 potentiometer
(Microwave Sensitivity). · To operate the detector
without light indication,
remove the W1 (LED) jumper.

11 12 13 14 15

PATROL-USM TECHNICAL Detection range:……………7m WARRANTY

DETECTION ZONE SPECIFICATIONS GSN Electronic Company Ltd.
Maximum protected volume:
Input voltage:............9 - 16Vdc …………........................ 200m³ warrants the product to be free
from defects in materials and
TOP VIEW
Current consumption Detection angle:…….........170° workmanship under condition
of observance of service
In standby mode:……….44mА Relay output:………………….. regulations and to be repaired
In alarm mode:………….95mА ………..NC; 60V; 120mA; 16Ω or replaced under absence of
mechanical damages for a
Warm-up period:….……...2sec Tamper output:………NC; 10Ω
limited period of five years
Operating temperature range: from the date of sale.
Anti-mask startup (boot)
………………...–30ºC to +70ºC
period:………………...30±5sec
Storage temperature range:
Alarm period:……...……...3sec ………..............–50ºC to +85ºC
Anti-mask alarm activation RFI immunity:…………...30V/m
delay:………………….....35sec at a frequency range
W2 – Operating mode setting 10MHz – 2GHz
Ultrasonic channel operating
W3 – Pulse programming jumper frequency:……………....40kHz EMI immunity:…………50000V
W4 – Ultrasonic channel Dimensions:………….………....
Microwave channel operating
sensitivity adjustment ..........105mm x 50mm x 22mm
frequency: ....................24GHz
R11 – MW channel sensitivity Weight:……………………...80g
adjustment Installation height:……2 - 2.5m
P/N: USM0PATUSM_ENG_REV.A

16 17 18 19 20