SPEC.No.

B 0 8 3 4 3 0 2 5 0 4
DATE A p r . 1 1 . 2 0 0 5

SPECIFICATIONS

Diesel Engine-Driven
AC Generator

MODEL ＴＬＧ－１２ＥＳＸ
［ 1-phase 2-wire 50Hz 220V ］

HEAD OFFICE

4-2-2, KAMITAKADA, NAKANOKU,

TOKYO 164-8510, JAPAN
TEL (03) 3228 1111
FAX (03) 5380 7171
1. APPLICATION

1.1 This specification covers the water-cooled, diesel engine-driven AC Generator model
TLG-12ESX ( hereafter referred to as generating set ).

1.2 This generating set shall be designed, manufactured and tested in accordance with the
latest standards of JIS, JEC and JEM.

JIS : Japanese Industrial Standard

JEC : Standard of The Japanese Electrotechnical Committee
JEM : The Standard of The Japan Electrical Manufacturer’s Association
Other matters which are not specifically mentioned in the above standards shall
be subject to Denyo Co., Ltd's production regulations.

2. GENERAL

2.1 Materials and Workmanship

The materials used in the manufacture of this equipment shall be of the high quality,
and shall be free from defects and imperfections.
All materials and apparatus not manufactured by Denyo Co.,Ltd. shall be the products of
well-known manufacturers.
The workmanship shall be of the high grade and in accordance with the most efficient,
up-to-date procedures.

2.2 Change

Minor changes after the final design may be made by Denyo Co., Ltd. without prior notice to
the Purchaser.
In case of major changes or additional equipment which may result in an increase or
decrease of equipment's cost, such modifications shall be made in writing and agreed to by
both parties prior to production and shall constitute an amendment to these specifications.

2.3 Tests and Inspections

Routine tests and inspections shall be final in our factory.

If any tests and inspections beyond the scope of Denyo's standard commercial procedures
are required by the Purchaser, charges for such inspections or tests shall be added to our
estimate.
Conditions of any such tests and inspections shall be mutually agreed upon between both
parties.

-1-
3. STRUCTURE

This generating set possess a solid structure ,and is comprised of a water-cooled diesel
engine and a generator ,which are directly coupled on a common base.
A coupling housing is employed to connect the generator to the engine.
Firm coupling of the engine and generator is ensured by tight connection of the housing
exterior.
The rotating section of the generator is directly coupled to the flywheel of the engine.
The generator is of single bearing construction and is of brushless type .
A heavy gauge steel bonnet and side door completely cover the engine ,generator and
accessories ,protecting the unit from effects of weather or possible handing damages at the
sight.
A lifting hook is attached to the balance point of the bonnet top.

4. SPECIFICATIONS

4.1 Ambient Conditions

This generating set should meet the following conditions:

(1) Ambient temperature : -5ﾟC or higher, 40ﾟC or lower

(2) Altitude : up to 500m above sea level
(3) Relative humidity : 85% or lower
(4) Place of installation : outdoor

-NOTE- Generator rated output is in accordance with JIS standard ambient conditions.
JIS standard ambient conditions
(A) Ambient temperature : 25 ℃
(B) Atmospheric pressure : 100kPa
(C) Relative humidity : 31 %

4.2 Dimensions and Weight

Length : 1400 mm
Width : 690 mm
Height : 930 mm
Dry Weight : 407 kg

-2-
4.3 AC Generator

Generator Model : TLG-12X2

Generator Type : Rotating-field ,protection type
synchronous generator
Excitation : Brushless type ( with AVR )
Continuous Duty Rating : 10.5 kVA
Voltage : 220 V
Current : 47.7 A
Frequency : 50 Hz
No. of Poles : 2
Speed : 3000 min-1
Power Factor : 1.0
Rating : Continuous
Phase : 1 (2 wires)
Insulation System : Class F
Cooling System : Self-ventilation

- NOTE -
Continuous Duty Rating : The generating set is designed for continuous operation
under normal load conditions with an overload capacity
(105% of rating capacity ) up to the standby rating for
intermittent periods.
Continuous duty rating is in accordance with JIS
standard ambient conditions.

4.4 Engine

Maker and Model : YANMAR 3TNV70-F

Type : Vertical, water-cooled,4-cycle, Diesel Engine
Rated Output : 12.6 kW / 3000 min-1
No.of Cylinders : 3
Bore × Stroke : 70 mm × 74 mm
Piston Displacement : 0.854 L
Direction of Rotation : Clockwise ( When viewed from the fan side )
Governor : Mechanical all speed governor
Cooling System : Water cooling by radiator with fan
Lubricating System : Gear pump
Starting Motor : Electric Start ( 12 V - 1.0 kW )
Charging Generator : 12 V - 180 W
Battery : 12 V - 45 Ah ×1 (55B24L)
Fuel : Diesel fuel (ASTM No.2 or equivalent)
Lubricating Oil : API service class, CC class or higher

- NOTE -
“Rated Output” is in accordance with JIS standard ambient conditions.

4.5 Capacity

Cooling water capacity : 3.5 L

Lube oil capacity : 3.8 L
Fuel tank capacity : 51 L

-3-
5. PERFORMANCE

5.1 AC Voltage Regulation

The AC voltage regulation from no load to full rated load under a rated power factor
shall not exceed ±1.0 % of 220V rated voltage.

5.2 Speed Regulation

The speed regulation from no load to rated load under a rated power factor shall be within
5% of rated speed.

5.3 Sound Level

The average sound level shall not exceed 67 dB(A) at 7 meters from the machine.

5.4 Limits of Temperature

Limits of temperature rise of the generator shall be in accordance with relevant Japanese
standards, based on ambient temperature not exceeding 40℃, and shall not exceed the
following:

Armature windings 85℃ (Insulation class F)

Field windings 85℃ (Insulation class F)
Bearing 40℃

-NOTE-
Method of measuring temperatures rise is thermometer method.

5.5 Dielectric Strength Test

The strength of the windings of the generator and control box shall meet the specifications
of the high voltage test according to Japanese standards:

Armature windings - Grounding AC 1500V (one minute)

Field windings - Grounding AC 1500V (one minute)
Electrical parts - Grounding AC 1500V (one minute)

-NOTE-
The dielectric strength test of semi-conductive parts such as diode will be carried out
without disconnecting the terminals.

-4-
6. INSTRUMENTATION ON THE CONTROL PANEL

6.1 for AC Power

Frequency Meter 1 pc.
AC Ammeter 1 pc.
AC Voltmeter 1 pc.
Voltage Regulator 1 pc.
Earth Leakage Circuit Breaker (ELCB) 1 pc.
AC Output Terminal (1-Phase, 2-wire) 1 pc.
Ground Terminal (for ELCB) 1 pc.

6.2 for Engine

Starter Switch 1 pc.
Hour Meter 1 pc.
Warning Lamp Unit 1 set
(oil press./water temp./charging /preheat)

7. SAFETY CONTROLS

The generating set shall be equipped with automatic safety controls which will shut down
the engine in the event of any abnormal condition such as :

Circuit breaker will

Engine shut down Warning lamp
trip
Low lubricating oil
pressure ○ - ○
High jacket water
temp. ○ - ○
Insufficient charge ○ - ○
Over current of
generator - ○ -
Earth leakage
current - ○ -
Mark ○ : Operate
Mark - : Not operate

8. ATTACHMENT

Instruction Manual 1 vol.

Parts List 1 vol.
Earth Bar 1 pc.
Fuse 1 pc.

9. COATING

The generating set and the engine shall be the manufacturer's standard colors.
(Munsell No. 7.5 BG 5 / 10 , No. 10PG4/1)

-5-