E-Z WELD® 206

Low VOC
Industrial Grade
Gray PVC Cement
GHS SAFETY DATA SHEET

SECTION I - PRODUCT AND COMPANY

IDENTIFICATION
Product Name: E-Z WELD® 206 Low VOC Industrial Grade Gray Medium
Body PVC Cement
Product Use: Low VOC Solvent Cement for bonding PVC Pipe & Fittings
Manufacturer: E-Z WELD Group LLC 1661 President Barack Obama Hwy,
Riviera Beach, FL 33404 USA Tel: 1-561-844-0241 Fax: 1-561-848-8958.
Supplier:
For Emergency: Transportation / Medical Issues: INFOTRAC Tel:
800-535-5053, +1 352-323-3500 (International).

SECTION 2 - HAZARDS IDENTIFICATION

Health
Acute Toxicity: Category 4
Skin Irritation: Category 3
Skin Sensitization: No
Eye: Category 2
Environmental
Acute Toxicity: None Known
Chronic Toxicity: None Known
Physical
Flammable Liquid: Category 2
GHS Label:

Signal Word: Danger

WHMIS Classification:
Class B, Division 2; Class D, Division 1B

Hazard Statements
H225: Highly flammable liquid and vapor
H319: Causes serious eye irritation
H332: Harmful if inhaled
H335: May cause respiratory irritation
H336: May cause drowsiness or dizziness
H351: Suspected of causing cancer
EUH019: May form explosive Peroxides
EUH066: Repeated exposure may cause skin dryness or cracking
Precautionary Statements
P210: Keep away from heat / sparks / open flames / hot surfaces - No
smoking
P261: Avoid breathing dust / fume / gas / mist / vapors / spray
P280: Wear protective gloves/protective clothing / eye protection / face
protection
P304+P340: IF INHALED: Remove victim to fresh air and keep at rest in
a position comfortable for breathing
P337+P313: Get medical advice / attention
P403+P233: Store in a well ventilated place. Keep container tightly
closed
P501: Dispose off contents / container in accordance with local regulation

SECTION - 3 COMPOSITION/INFORMATION
ON INGREDIENTS
REACH Pre- Concentration
CAS# EINECS# registration Number % by Weight
Tetrahydrofuran (THF) 109-99-9 203-726-8 05-2116297729-22-0000 42-60
Methyl Ethyl Ketone (MEK) 78-93-3 201-159-0 05-2116297728-24-0000 5-25
Cyclohexanon 108-94-1 203-631-1 05-2116297718-25-0000 10-25
Acetone 67-64-1 200-662-2 05-2116297713-35-0000 5-15

All of the constituents of this adhesive product are listed on the TSCA
inventory of chemical substances maintained by the US EPA, or are exempt
from that listing.
* Indicates this chemical is subject to the reporting requirements of Section
313 of the Emergency Planning and Community Right-to-Know Act of 1986
(40CFR372).

OUR NAME IS OUR BOND

# indicates that this chemical is found on Proposition 65’s List of chemicals
known to the State of California to cause cancer or reproductive toxicity.

www.e-zweld.com
 SECTION 4 - FIRST AID MEASURES Engineering Controls: Use local exhaust as needed. SECTION 13 - WASTE DISPOSAL CONSIDERATIONS
Monitoring: Maintain breathing zone airborne concentrations below
Contact With Eyes: Flush eyes immediately with plenty of water for 15 Follow local and national regulations. Consult disposal expert.
exposure limits.
minutes and seek medical advice immediately.
Personal Protective Equipment (PPE):
Skin Contact: Remove contaminated clothing and shoes. Wash skin
Eye Protection: Avoid contact with eyes, wear splash-proof chemical SECTION 14 - TRANSPORT INFORMATION
thoroughly with soap and water. If irritation develops, seek medical
goggles, face shield, safety glasses (spectacles) with brow guards and
advice. Proper Shipping Name: Adhesives
side shields, etc. as may be appropriate for the exposure.
Inhalation: Remove to fresh air. If breathing is stopped, give artificial Hazard Class: 3
Skin Protection: Prevent contact with the skin as much as possible. Butyl
respiration. If breathing is difficult, give Oxygen. Seek medical advice. Secondary Risk: None
rubber gloves should be used for frequent immersion.
Ingestion: Rinse mouth with water. Give 1 or 2 glasses of water or milk to Identification Number: UN 1133
Use of solvent-resistant gloves or solvent-resistant barrier cream should
dilute. Do not induce vomiting. Seek medical advice immediately. Packing Group: PG II
provide adequate protection when normal adhesive application practices
Likely Routes of Exposure: Inhalation, Eye and Skin Contact. Label Required: Class 3 Flammable Liquid
and procedures are used for making structural bonds.
Acute Symptoms & Effects: Marine Pollutant: No
Respiratory Protection: Prevent inhalation of the solvents. Use in a
Inhalation: Severe overexposure may result in nausea, dizziness,
well-ventilated room. Open doors and/or windows to ensure airflow and
headache. Can cause drowsiness, irritation of eyes and nasal passages. Exception for Ground Shipping
air changes. Use local exhaust ventilation to remove airborne
Eye Contact: Vapors slightly uncomfortable. Overexposure may result in DOT Limited Quantity: Up to 5L per inner packaging, 30 kg gross
contaminants from employee breathing zone and to keep contaminants
severe eye injury with corneal or conjunctival inflammation on contact weight per package.
below levels listed above. With normal use, the Exposure Limit Value will
with the liquid. Consumer Commodity: Depending on packaging, these quantities may
not usually be reached. When limits approached, use respiratory
Skin Contact: Liquid contact may remove natural skin oils resulting in qualify under DOT as "ORM-D".
protection equipment.
skin irritation. Dermatitis may occur with prolonged contact. TDG Information
Ingestion: May cause nausea, vomiting, diarrhea and mental TDG Class: Flammable Liquid 3
sluggishness. Shipping Name: Adhesives
Chronic (long-term) Effects: Category 2 Carcinogen SECTION 9 - PHYSICAL AND CHEMICAL PROPERTIES UN Number / Packing Group: UN 1133, PG II
Appearance: Gray, medium syrupy liquid
Odor: Ketone.
SECTION 5 - FIREFIGHTING MEASURES SECTION 15 - REGULATORY INFORMATION
pH: Not Applicable
Precautionary Label Information: Highly Flammable, Irritant, Carc. Cat. 2
Suitable Extinguishing Media: Dry chemical powder, Carbon Dioxide Melting / Freezing Point: -108.5 °C (-163.3 °F) Based on first melting
Ingredient Listings: USA TSCA, Europe EINECS, Canada DSL, Australia
Gas, Foam, Halon, Water fog. component: THF
AICS, Korea ECL/TCCL, Japan MITI (ENCS)
Unsuitable Extinguishing Media: Water spray or Steam. Boiling Point: 56 °C (133 °F) Based on first boiling component: Acetone
Symbols: F, Xi
Exposure Hazards: Inhalation and dermal contact Flash Point: -20 °C (-4 °F) TCC based on Acetone
Risk Phrases: R11: Highly flammable • R19: May form explosive
Combustion Products: Oxides of Carbon, Hydrogen Chloride and Smoke Specific Gravity: 0.963 ± 0.10 @ 73 °F ( 23 °C )
peroxide • R20: Harmful by inhalation. • R36/37: Irritating to eyes and
Protection for Firefighters: Self-contained breathing apparatus or Solubility: Solvent portion soluble in water, resin portion separates out.
respiratory system. • R66: Repeated exposure may cause skin dryness
full-face positive pressure airline masks. Partition Coefficient n-octanol/water: Not Available
or cracking • R67: Vapors may cause drowsiness and dizziness
Health: HMIS: 2 • NFPA: 2 0-Minimal Auto-ignition Temperature: 321 °C (610 °F) based on THF
1-Slight Safety Phrases: S2: Keep out of the reach of children • S9: Keep
Flammability: HMIS: 3 • NFPA: 3 Decomposition Temperature: Not Applicable
2-Moderate container in a well-ventilated place. • S16: Keep away from sources of
Reactivity: HMIS: 0 • NFPA: 0 3-Serious VOC Content: When applied as directed, per SCAQMD Rule 1168, Test
ignition - No smoking. • S25: Avoid contact with eyes. • S26: In case of
PPE: HMIS: B • NFPA: - 4-Severe Method 316A,VOC content is: < 510 g/l.
contact with eyes, rinse immediately with plenty of water and seek
Odor Threshold: 0.88 ppm (Cyclohexanone)
medical advice. • S29: Do not empty into drains. • S33: Take
Boiling Range: 56 °C (151 °F) to 156 °C (313 °F)
SECTION 6 - ACCIDENTAL RELEASE MEASURES Evaporation Rate: > 1.0 (BUAC = 1)
precautionary measures against static discharges. • S46: If swallowed,
seek medical advise immediately and show this can or label.
Personal Precautions: Keep away from heat, sparks and open flame. Flammability: Category 2
Provide sufficient ventilation, use explosion-proof exhaust ventilation Flammability Limits: LEL: 1.1% based on Cyclohexanone
equipment or wear suitable respiratory protective equipment. Prevent UEL: 12.8% based on Acetone
contact with skin or eyes (see section 8). Vapor Pressure: 190 mm Hg @ 20 °C (68 °F) Acetone SECTION 16 - OTHER INFORMATION
Environmental Precautions: Prevent product or liquids contaminated Vapor Density: >2.0 (Air = 1) Specification Information:
with product from entering sewers, drains, soil or open water source. Viscosity: Medium body Department Issuing Data Sheet: Environmental Health & Safety
Methods for Cleaning up: Clean up with Sand or other inert absorbent E-mail Address: [email protected]
material. Transfer to a closable Steel Vessel. Training Necessary: Yes, training in practices and procedures
contained in product literature.
Materials Not to be Used for Clean up: Aluminum or Plastic Containers SECTION 10 - STABILITY AND REACTIVITY
Reissue Date / Reason for Reissue: October-2018 / changed format
Stability: Stable Intended Use of Product: Solvent cement for bonding PVC pipe &
SECTION 7 - HANDLING AND STORAGE Hazardous Decomposition Products: None in normal use. When forced fittings
Handling: Avoid breathing of vapor, avoid contact with eyes, skin and to burn, this product gives off Oxides of Carbon, Hydrogen Chloride and All ingredients are compliant with the requirements of the European
clothing. smoke. Directive on RoHS (Restriction of Hazardous Substances).
Keep away from ignition sources, use only electrically grounded handling Conditions to Avoid: Keep away from heat, sparks, open flame and other This product is intended for use by skilled individuals at their own risk.
equipment and ensure adequate ventilation/fume exhaust hoods. ignition sources. The information contained herein is based on data considered accurate
Do not eat, drink or smoke while handling. Incompatible Materials: Oxidizers, strong acids and bases, Amines, based on current state of knowledge
Storage: Store in ventilated room or shade below 43 °C (110 °F) and Ammonia. and experience. However, no warranty is expressed or implied regarding
away from direct sunlight. the accuracy of this data or the results to be obtained from the use
Keep away from ignition sources and incompatible materials: Caustics, thereof.
Ammonia, Inorganic Acids, Chlorinated Compounds, strong Oxidizers and SECTION 11 - TOXICOLOGICAL INFORMATION
Isocyanates.
Toxicity LD 50 LC 50 Target Organs
Follow all precautionary information on container label, product bulletins
Tetrahydrofuran (THF) Oral: 2842 mg/kg (rat)Oral: 5800 mg/kg (rat) Inhalation 3 hrs. 21,000 mg/m3 (rat) STOT SE3
and solvent cementing literature.
Methyl Ethyl Ketone (MEK) Oral: 2737 mg/kg (rat), Dermal: 6480 mg/kg (rabbit) Inhalation 8 hrs. 23,500 mg/m3 (rat) STOT SE3
Cyclohexanone Oral: 1535 mg/kg (rat), Dermal: 948 mg/kg (rabbit) Inhalation 4 hrs. 8,000 PPM (rat)
SECTION 8 - PRECAUTIONS TO CONTROL Acetone Oral: 5800 mg/kg (rat) Inhalation 50,100 mg/m3 (rat) STOT SE3

EXPOSURE / PERSONAL PROTECTION Reproductive Effects: Not Established

Exposure Limits: Teratogenicity: Not Established
Component ACGIH TLV ACGIH STEL OSHA PEL OSHA STEL Mutagenicity: Not Established
Tetrahydrofuran (THF) 50 ppm 100 ppm 200 ppm N/E Embryotoxicity: Not Established
Methyl Ethyl Ketone (MEK) 200 ppm 300 ppm 200 ppm N/E Sensitization to Product: Not Established
Cyclohexanone 20 ppm 50 ppm 50 ppm N/E Synergistic Products: Not Established
Acetone 500 ppm 750 ppm 1000 ppm N/E

OSHA PEL CAL/OSHA CAL/OSHA CAL/OSHA SECTION 12 - ECOLOGICAL INFORMATION

Component Ceiling PEL Ceiling STEL
Ecotoxicity: None Known
Tetrahydrofuran (THF) N/E 200 ppm N/E 250 ppm
Mobility: In normal use, emission of volatile organic compounds (VOC's)
Methyl Ethyl Ketone (MEK) N/E 200 ppm N/E 300 ppm
to the air takes place, typically at a rate of < 510 g/l.
Cyclohexanone N/E 25 ppm N/E N/E
Degradability: Not readily biodegradable
Cyclohexanone N/E 500 ppm 3000 ppm 750 ppm
Bioaccumulation: Minimal to none.
REV/10/18

www.e-zweld.com