5G RAN2.0 Beam Management Huawei

Download as pdf or txt
Download as pdf or txt
You are on page 1of 42
At a glance
Powered by AI
The key takeaways are about beam management in 5G networks, including static beam management, cell-level and user-level beam management, beam scanning and scheduling, and related monitoring items.

Beam management refers to the management of beams in 5G networks. Its purpose is to select the optimal beam for communication between the base station and user equipment to improve coverage and throughput.

There are two types of beam management: cell-level beam management and user-level beam management. Cell-level beam management includes beam scanning, scheduling and maintenance. User-level beam management involves beam tracking and measurement using reference signals.

5G RAN2.

0 Beam Management

www.huawei.com

Date: May 2018

[email protected]
Copyright © 2018 Huawei Technologies Co., Ltd. All rights reserved.
Objectives
⚫ Upon completion of this course, you will be able to:
 Describe the purpose and basic principles of the Beam Management feature.

 Understand basic functions of scenario-based broadcast beams.

 Understand the principles of tilt adjustment.

 Understand the basic principles of user-level beam management.

 Figure out the parameter configuration of the Beam Management feature.

Copyright © 2018 Huawei Technologies Co., Ltd. All rights reserved. Page 2
Contents
1. Beam Management Overview

2. Low-Frequency Beam Management

3. High-Frequency Beam Management

4. Feature Activation

5. Related Monitoring Items

Copyright © 2018 Huawei Technologies Co., Ltd. All rights reserved. Page 3
Beam Management Overview
Massive MIMO can use either static weights or the dynamic weights.
… •
… … Static weights: weights corresponding to static beams
Digital BF Analog BF
(Baseband) (AAU) Analog beam ① The UE provides the SSB index or the CSI-RS index. SSB is short
Digital beam for SS/PBCH block and CSI-RS is short for channel state
information-reference signal.
② The gNodeB obtains the static beam weight by using the mapping
relationship between the index and the beam ID.
UE •
Digital beam tracking Analog beam tracking Dynamic weights: SRS weights or PMI weights (SRS is short for
Get BF matrix from SRS or Get BF weights from best beam
PMI feedback. ID feedback. sounding reference signal and PMI is short for precoding matrix
UE feedback: indication.)
best beam ID
SRS, or PMI ① The gNodeB obtains SRS weights based on the channel estimation
through SRS measurement and obtains PMI weights through the
1 PA drives 3 antennas. PMI reported by the UE.

PA
The figure on the left uses an AAU working on the C-band and
RF chain
supporting 64T64R as an example.
For static beams, digital weighting is performed on the baseband part.
beamforming
Baseband

64 PAs

The Beam Management feature covers only static weights, that is, the
RF chain PA management of static beams.

Antenna:
(8Hx12Vx2P)

Page 4
Beam Management and Its Subitems
SSB beam
scanning
Cell-level beam
management PRACH beam
scanning
Beam
management SRS beam
Beam scanning measurement
mode CSI-RS beam
User-level beam
management Beam scanning
maintenance
Beam scheduling

Copyright © 2018 Huawei Technologies Co., Ltd. All rights reserved. Page 5
Contents
1. Beam Management Overview

2. Low-Frequency Beam Management

3. High-Frequency Beam Management

4. Feature Activation

5. Related Monitoring Items

Copyright © 2018 Huawei Technologies Co., Ltd. All rights reserved. Page 6
Contents
2. Low-Frequency Beam Management
2.1 Overview

2.2 Scenario-based Broadcast Beams

2.3 Tilt and Azimuth Adjustment

2.4 User-Level Beam Management

Copyright © 2018 Huawei Technologies Co., Ltd. All rights reserved. Page 7
Overview
Beam Beam Beam Scanning/
Beam Reporting and Maintenance Application Scope
Applicability Type Quantity Measurement Mode
PBCH/SS; common
SSB ≤ 8 scenario-
SSB beam scanning No reporting PDCCH and PDSCH
beam based beams
that send SIBs
Cell-level Scenario-based beams for the Msg1 to Msg5; PDSCH,
PRACH PDCCH, PUCCH, and
PRACH 8 scenario- Beams received by
Four optimal beams are maintained in PUSCH before SRS
beam based beams PRACH
each of the left and right polarization measurement result is
directions. reported
The polarization sequence is not
distinguished for beams measured by
maintenance SRS in the uplink.
Static beams based on The polarization sequence is
PDSCH, PDCCH,
Static SRS measurement or distinguished for beams received by
User-level 32 beams PUCCH, PUSCH, and
beam CSI-RS beam maintenance SRS in the downlink or
CSI-RS
scanning those measured by CSI-RS.
Four optimal beams are maintained in
each of the left and right polarization
directions.

Copyright © 2018 Huawei Technologies Co., Ltd. All rights reserved. Page 8
Overview
A main framework of beam management includes: beam configuration, beam
scanning/measurement, beam reporting, beam maintenance, and beam usage.

For RAN2.0, this document covers the following contents:


• Beam configuration: mainly the beam configuration of SSB

• Beam scanning/measurement: mainly the beam scanning of SSB

• Beam reporting and maintenance: Beams from the PRACH and SRS are involved based on the
reciprocity. Refer to the preceding table, and details are not described in the following pages.
• Beam usage: Based on the result of beam maintenance, each channel (PDSCH, PDCCH,
PUCCH, PUSCH, and CSI-RS) selects an optimal beam in each TTI.

Copyright © 2018 Huawei Technologies Co., Ltd. All rights reserved. Page 9
Uplink Beam Selection
Uplink Beam Type and Quantity Number of Beams Reported by Number of Used Beams
Channel (Dual Polarization) L1 (for L2 Beam Selection) (Static Weight)

MSG2/MSG4 uses one beam in each of the left


4 optimal beams in each of the left
PRACH Scenario-based beam: 16 and right polarization directions.
and right polarization directions
MSG3/MSG5 uses all beams for receiving.

64 (64 T, 8 x 4 x 2) 64 (64 T, 8 x 4 x 2)
SRS 8 beams (for TA and 3I measurements)
32 (32T) 32 (32T)

According to the beams reported by the


PUCCH 16 N/A SRS/PRACH, L2 selects:
PUCCH: 8 narrow beams

According to the beams reported by the


SRS/PRACH, L2 selects:
PUSCH 16 N/A 16 narrow beams
(8 beams are used for TA and Doppler
measurements.)

Copyright © 2018 Huawei Technologies Co., Ltd. All rights reserved. Page 10
Downlink Beam Selection
Downlink Beam Type and
Transmission Description
Channel Quantity
CSI-RS beam scanning and CSI-RS
3I measurement are independent
According to the beams reported by SRS/CSI-RS, L2 selects: processes.
CSI-RS Narrow: 2/4/8 optimal beams in each of the left and right polarization directions. CSI-RS beam scanning is enabled
Each port is mapped to a single-polarized beam. only when the SRS static beam
measurement is inaccurate or not
reported.
P-SS/S-SS
The PBCH implements beam tracking,
/PBCH/common Narrow or wide: 8
Periodic beam scanning optimal beam reporting, beam
PDCCH/common at most
handover, and cell handover.
PDSCH/TRS
User-specific According to the beams reported by SRS/PRACH/CSI-RS, L2 selects: The left and right polarization data is
Narrow or wide: 2
PDCCH optimal beams in each of the left and right polarization directions of PRACH/SRS. the same.
According to the beams reported by SRS/PRACH/CSI-RS and the number of streams on
PDSCH, L2 selects beams according to the following rules:
(1) In PMI weights (the description of transmission beams is the same as that in CSI-RS):
The following exists:
• 1 beam for each of the left and right polarization directions with 2 antenna ports
User-specific Narrow or wide: 1. SRS dynamic weight+RI (8 streams)
• 2 beams for each of the left and right polarization directions with 4 antenna ports
PDSCH 2/4/8 2. Static weight (4 streams)
• 4 beams for each of the left and right polarization directions with 8 antenna ports
3. PMI+static weight (8 streams)
(2) In DFT weights:
• 1 beam for each of the left and right polarization directions when the rank is 1 or 2
• 2 beams for each of the left and right polarization directions when the rank is 4

Copyright © 2018 Huawei Technologies Co., Ltd. All rights reserved. Page 11
Beams

SSB/PRACH Beams Static Beams (SRS/CSI-RS)

0/8 1/9 2/10 3/11 4/12 5/13 6/14 7/15 24/56 25/57 26/58 27/59 28/60 29/61 30/62 31/63

16/48 17/49 18/50 19/51 20/52 21/53 22/54 23/55


Note:
Different colors indicate different beam IDs.
8/40 9/41 10/42 11/43 12/44 13/45 14/46 15/47
SSB uses a maximum of eight beams.
PRACH uses eight beams. The beam
0/32 1/33 2/34 3/35 4/36 5/37 6/38 7/39
distributions vary with scenarios.

Copyright © 2018 Huawei Technologies Co., Ltd. All rights reserved. Page 12
Contents
2. Low-Frequency Beam Management
2.1 Overview

2.2 Scenario-based Broadcast Beams

2.3 Tilt and Azimuth Adjustment

2.4 User-Level Beam Management

Copyright © 2018 Huawei Technologies Co., Ltd. All rights reserved. Page 13
2. Broadcast Beams
⚫ 5G NR improves the broadcast mechanism based on wide beams in the LTE
era and uses narrow beam scanning in polling mode to cover the entire cell.
The purpose of beam management is to properly design narrow beams and
select appropriate time-frequency resources to transmit narrow beams.
⚫ Narrow beams can:
 Direct the emitted energy at target users, increasing the demodulation signal-to-
noise ratio (SNR) of target users and improving the transmission success rate.
Narrow beams are especially suitable for high frequencies.
 Improve the system coverage and the coverage of control channels, increasing the
cell radius.

Copyright © 2018 Huawei Technologies Co., Ltd. All rights reserved. Page 14
2.1 Broadcast Channel Narrow Beams
NR broadcast beams are N narrow beams with different fixed directions. The broadcast beam coverage of the
cell is completed by sending different narrow beams at different moments. By scanning each narrow beam, the
UE obtains an optimal beam, and completes synchronization and system message demodulation.
#0
#1

#2

.
.
.

#N-3

#N-2
#N-1
Time


For the initial cell search, the transmission period of the SSB
is 20 ms and each transmission is complete within 5 ms.

The PBCH period is 80 ms, and the SSB is transmitted by
four times within 80 ms.

There are a maximum of eight low-frequency SSBs.
2.2 Scenario-based Broadcast Beams
Broadcast beams can be used in various scenarios, such as buildings and squares.

In square scenarios, wide beams are used at the


cell center to ensure the access. Narrow beams
For high-rise buildings, beams with wide vertical
are used at the cell edge to improve coverage.
coverage are used to improve the vertical coverage.

Massive MIMO cell


Neighboring cell

In business districts, there are both squares In inter-cell interference scenarios, beams with
and high-rise buildings. Beams providing large narrow horizontal scanning scope are used to
horizontal and vertical coverage are used. avoid strong interference sources.

Copyright © 2018 Huawei Technologies Co., Ltd. All rights reserved. Page 16
Horizontal Vertical
Pattern Tilt (°) Azimuth (°) 64T 32T (16H2V) 32T (8H4V) Application Scenario
HPBW HPBW
H105V6 H105V6 H65V12
0 Default scenario (DEFAULT) Tilt: –2 to 9 Tilt: –2 to 9 Tilt: 0 to 6 This scenario is a common and default scenario using typical 3-sector networking, and applies to squares.
Azimuth: 0 Azimuth: 0 Azimuth: 0
This scenario uses nonstandard 3-sector networking to provide wide horizontal coverage, and applies to squares as well
1 110° 6° –2 to 9 0 Y Y N as large and wide buildings. The horizontal coverage area in this scenario is larger than that in scenario 2. The coverage
near the cell center in this scenario is slightly poorer than that in scenario 2.
This scenario uses nonstandard 3-sector networking. When strong interference sources exist in neighboring cells, the
2 90° 6° –2 to 9 –10 to 10 Y N N horizontal coverage of a cell can be narrowed down to mitigate the interference from neighboring cells. This scenario
applies to low-floor coverage since the vertical coverage scope is small.
This scenario uses nonstandard 3-sector networking. When strong interference sources exist in neighboring cells, the
3 65° 6° –2 to 9 –22 to 22 Y N Y horizontal coverage of a cell can be narrowed down to mitigate the interference from neighboring cells. This scenario
applies to low-floor coverage since the vertical coverage scope is small.
4 45° 6° –2 to 9 –32 to 32 Y N N This scenario applies to low-rise buildings and hotspot coverage.
5 25° 6° –2 to 9 –42 to 42 Y N N This scenario applies to low-rise buildings and hotspot coverage.
This scenario uses nonstandard 3-sector networking and provides relatively large horizontal coverage and middle-floor
6 110° 12° 0 to 6 0 Y Y N
coverage
This scenario uses nonstandard 3-sector networking. When strong interference sources exist in neighboring cells, the
7 90° 12° 0 to 6 –10 to 10 Y Y N horizontal coverage of a cell can be narrowed down to mitigate the interference from neighboring cells. This scenario
applies to middle-floor coverage since the vertical coverage scope is large.
This scenario uses nonstandard 3-sector networking. When strong interference sources exist in neighboring cells, the
8 65° 12° 0 to 6 –22 to 22 Y Y N horizontal coverage of a cell can be narrowed down to mitigate the interference from neighboring cells. This scenario
applies to middle-floor coverage since the vertical coverage scope is large.
9 45° 12° 0 to 6 –32 to 32 Y N N This scenario applies to middle-rise buildings and hotspot coverage.
10 25° 12° 0 to 6 –42 to 42 Y N N This scenario applies to middle-rise buildings and hotspot coverage.
11 15° 12° 0 to 6 –47 to 47 Y N N This scenario applies to middle-rise buildings and hotspot coverage.
This scenario uses nonstandard 3-sector networking and provides relatively large horizontal coverage and high-floor
12 110° 25° 6 0 Y Y N
coverage.
This scenario uses nonstandard 3-sector networking. When strong interference sources exist in neighboring cells, the
13 65° 25° 6 –22 to 22 Y Y Y horizontal coverage of a cell can be narrowed down to mitigate the interference from neighboring cells. This scenario
applies to high-floor coverage since the vertical coverage scope is the largest (among these scenarios).
14 45° 25° 6 –32 to 32 Y Y N This scenario applies to high-rise buildings and hotspot coverage.
15 25° 25° 6 –42 to 42 Y Y N This scenario applies to high-rise buildings and hotspot coverage.
16 15° 25° 6 –47 to 47 Y N N This scenario applies to high-rise buildings and hotspot coverage.

Note:
It is recommended that the cell be deactivated before modifying the coverage scenario of broadcast beams. Otherwise, the cell will be reestablished after the modification.
Three patterns of 8H4V products do not support azimuth adjustment.

Copyright © 2018 Huawei Technologies Co., Ltd. All rights reserved. Page 17
➢ Generally, the default scenario is The following key parameters are used to select a scenario:
recommended and is applicable to typical 3- • h: site height
sector networking. • d: distance between the UE and the base station
➢ If the requirements for horizontal coverage are • α: beam scanning range
high, it is recommended that scenario 1, 6, or • Direction of the normal line
12 be used. In this case, cell edge UEs can For example, the 64T 10 dB beamwidth is 45°, and the normal direction of the
obtain higher beam gains and the coverage at beams is horizontal. Assuming that the distance between the building and the
the cell edge is improved. base station is 70 m and the base station height is 25 m, the beams can cover
➢ If a fixed interference source exists at the cell floors below 54 m vertically. The horizontal coverage range can be calculated
edge, scenario 2, 3, 7, 8, 9, or 13 can be used similarly. In actual networking, both horizontal and vertical ranges must be
to narrow the horizontal coverage area and considered.
avoid the interference.
➢ When only isolated buildings exist, scenario 4, Height of covered
floors = 25 + 70 x
5, 9, 10, 11, 14, 15, or 16 is recommended to tan(22.5°) ≈ 54 m
provide small horizontal coverage. These
scenarios are not suitable for continuous
networks. ≈ 30 m
➢ When only low-rise buildings exist, you can
select a scenario from scenarios 1 to 5. 25 m α = 45° Horizontal
➢ When middle-rise buildings exist, you can normal line

select a scenario from scenarios 6 to 11. 25 m

➢ When high-rise buildings exist, you can select


a scenario from scenarios 12 to 16. h = 25 m

d = 70 m

Copyright © 2018 Huawei Technologies Co., Ltd. All rights reserved. Page 18
Contents
2. Low-Frequency Beam Management
2.1 Overview

2.2 Scenario-based Broadcast Beams

2.3 Tilt and Azimuth Adjustment

2.4 User-Level Beam Management

Copyright © 2018 Huawei Technologies Co., Ltd. All rights reserved. Page 19
2.3 Tilt and Azimuth Adjustment
To reduce the difficulty in site selection planning and site optimization and to save optimization and coordination
costs, remote downtilt adjustment is required. The tilts and azimuths of broadcast channel narrow beams can be
entirely adjusted in the unit of 1°through the parameter setting.
In scenarios where the interference from neighboring cells is severe, users can adjust the tilt and azimuth to
make the beams target at users in the local cell. This reduces the overlapped coverage in neighboring cells. In
addition, more beam directions can be achieved by adjusting the tilt and azimuth, meeting different coverage
requirements and implementing flexible networking.

The beam gain The beam gain Part of the


The beam gain is
decreases when is the greatest beam gain
the greatest
the preset downtilt when the decreases
when the preset
is not used. preset azimuth when the
downtilt is used.
is used. preset azimuth
is not used.

Copyright © 2018 Huawei Technologies Co., Ltd. All rights reserved. Page 20
2.3 Tilt and Azimuth Adjustment
Tilt adjustment is not supported (in scenarios 12 to 16) because the vertical scanning range has reached the
upper limit.
Azimuth adjustment is not supported (in scenarios 0, 1, 6, and 12) because the horizontal scanning range has
reached the upper limit.
The adjustment range is based on the parameter setting. Then, the parameter is substituted into the steering
vector. The steering vector is multiplied by the initial weight matrix to obtain the final steering vector, which is then
sent to the baseband part.
Note: Only the maximum adjustment capability is provided here. In actual situations, when the tilt is adjusted to a
certain degree, the side lobe suppression may not be sufficient. The adjustment range varies according to the
specific requirements.
If the upper side lobe meets the suppression requirement of 12 dB, the preset downtilt (6°) is used as the
reference. For digital RET, the increase range is 8° and the decrease range is 3°.
⚫ The tilt adjustment range in scenarios 1 to 5 (with a vertical 3 dB beamwidth of 6°) is –2°to 9°.
⚫ The tilt adjustment range in scenarios 6 to 11 (with a vertical 3 dB beamwidth of 12°) is 0° to 6°.

Copyright © 2018 Huawei Technologies Co., Ltd. All rights reserved. Page 21
Contents
2. Low-Frequency Beam Management
2.1 Overview

2.2 Scenario-based Broadcast Beams

2.3 Tilt and Azimuth Adjustment

2.4 User-Level Beam Management

Copyright © 2018 Huawei Technologies Co., Ltd. All rights reserved. Page 23
2.3 User-Level Beam Management
SRS-based Static Beam Measurement CSI-RS Beam Scanning
• Obtain an optimal beam through Aperiodic Periodic
• Obtain an optimal beam through SRS static
the scanning on the UE side and
beam measurement on the base station side. SRS √ √ (40 ms)
feedback of CSI-RS beams.
• It is applicable to reciprocal channels when SRS
• It is used when the SINR of the CSI-RS √ N/A
channel quality near or at the cell center is good.
SRS at the cell edge is low.

SRS static beam measurement CSI-RS scanning


The SRS beam quality of
UEs at the cell edge is poor. Aperiodic: priority-based scheduling
√ CSI-RS 10 ms: four times
SRS 10 ms: four times

Proper beams cannot be selected for UEs at


the cell edge due to poor SRS channel quality.

Proper beams are selected for Proper beams are selected


UEs at the cell center. for UEs at the cell edge.

Copyright © 2018 Huawei Technologies Co., Ltd. All rights reserved. Page 24
Contents
1. Beam Management Overview

2. Low-Frequency Beam Management

3. High-Frequency Beam Management

4. Feature Activation

5. Related Monitoring Items

Copyright © 2018 Huawei Technologies Co., Ltd. All rights reserved. Page 25
Contents
3. High-Frequency Beam Management
3.1 Overview

3.2 Broadcast Beams

3.3 Tilt Adjustment

3.4 User-Level Beam Management

Copyright © 2018 Huawei Technologies Co., Ltd. All rights reserved. Page 26
Overview
Beam Beam Beam Scanning/
Beam Reporting and Maintenance Application Scope
Applicability Type Quantity Measurement Mode
Initial access phase: One optimal beam is SSB, common PDCCH and
maintained in both the left and right polarization PDSCH sending SIB, Msg2,
directions. and Msg4
SSB Connected mode: Periodic scanning is implemented. After a UE accesses the
21 SSB beam scanning
beam After DCI scheduling is performed, only one optimal network, the optimal beam for
Cell-level beam is reported along with the PUSCH. Filtering is periodic level-1 scanning can
performed for the beam together with the optimal also be used by the PDCCH,
beam set maintained by user-level CSI-RS. PDSCH, or CSI-RS.
One-to-one mapping is performed between the Msg3 and Msg5; PUCCH and
PRACH Beams received by
21 beams received by PRACH and SSB beams and the PUSCH before the SRS
beam PRACH
beams are received by PRACH at fixed positions. measurement is reported

Aperiodic beam scanning: Several beams near the


optimal beam are selected for scanning. After DCI
CSI-RS CSI-RS beam scheduling is performed, the beam is reported along
60 PDSCH, PDCCH, and CSI-RS
beam scanning with the PUSCH. A maximum of four CSIs and
User-level RSRPs can be reported.
Each TRX maintains a set of four optimal beams.

The optimal beam set maintained in the downlink is


SRS Beams received by
60 used as an input, and is scanned again by using an PUCCH and PUSCH
beam SRS
SRS, and is sorted again.

Copyright © 2018 Huawei Technologies Co., Ltd. All rights reserved. Page 27
Beam Management Process

PRACH beam CSI-RS beam SRS beam Beam Beam


SSB beam scanning
scanning measurement measurement maintenance recovery

P1: Periodic SSB beam scanning is implemented


P2: Precise CSI-RS beam scanning is P3: Narrow beam scanning is
on the base station side. At the same time, wide
implemented on the base station side. implemented on the UE side.
beam scanning is implemented on the UE side.

Copyright © 2018 Huawei Technologies Co., Ltd. All rights reserved. Page 28
Beam Management Process
Step 1 Step 2 Step 3 Step 4 Step 5 Step 6 Step 7 Step 8

The UE side uses


The base The UE in the the corresponding
station The UE uses PRACH scanning RAR and connected mode Configure CSI-
MSG3 and wide beam to
sends cell- wide beam is used to obtain MSG4 use actively triggers RS secondary
MSG5 use receive signals, and
level scanning to the optimal the SSB reporting. beam scanning
the same measures and
narrow determine the PRACH beam and optimal Then, periodic to indicate the
PRACH reports the CRI and
beams optimal the optimal SSB SSB SSB optimal beams
beam. RSRP
through receive wide beam is implicitly beam. measurement is of the PDCCH
corresponding to the
SSB polling. beam. carried. performed. and PDSCH.
optimal beam on the
base station side.

Step 15 Step 14 Step 13 Step 12 Step 11 Step 10 Step 9

The UE sends The upper layer The UE selects the


The base station The base The base station
a beam instructs the UE The UE fails optimal narrow
sends downlink station sends uses the SRS to
recovery to perform the to detect the beams, the base
beams according cell-level measure the optimal
request (similar latest available beams and station maintains
to information narrow beams beam set maintained
to PRACH) to beam sends an the optimal beam
reported by the through SSB in the downlink and
the base station measurement, indication to set, and the uplink
UE, and delivers polling. selects the optimal
according to the and selects the upper and downlink beam
specific DCI to (Repeat step beams for the
candidate candidate layer. sets are maintained
the UE. 1.) PUCCH and PUSCH.
beams. beams. separately.

Copyright © 2018 Huawei Technologies Co., Ltd. All rights reserved. Page 29
Contents
3. High-Frequency Beam Management
3.1 Overview

3.2 Broadcast Beams

3.3 Tilt Adjustment

3.4 User-Level Beam Management

Copyright © 2018 Huawei Technologies Co., Ltd. All rights reserved. Page 30
Broadcast Channel Narrow Beams
Broadcast beams are N narrow beams with different fixed directions. The broadcast beam coverage
of the cell is completed by sending different narrow beams at different moments. By scanning each
narrow beam, the UE obtains an optimal beam, and completes synchronization and system
message demodulation.
#0
#1

#2

.
.
.

#N-3

#N-2
#N-1
Time


For the initial cell search, the transmission period of the SSB is 20 ms and each
transmission is complete within 5 ms.

The PBCH period is 80 ms, and the SSB is transmitted by four times within 80 ms.

There are a maximum of 64 high-frequency SSBs.

Copyright © 2018 Huawei Technologies Co., Ltd. All rights reserved. Page 31
Contents
3. High-Frequency Beam Management
3.1 Overview

3.2 Broadcast Beams

3.3 Tilt Adjustment

3.4 User-Level Beam Management

Copyright © 2018 Huawei Technologies Co., Ltd. All rights reserved. Page 32
Tilt Adjustment in High Frequency Bands
Due to architecture factors, the 19A version does not support dynamic weights. Therefore,
approximate downtilt adjustment can be implemented by deleting beams.
The tilt adjustment range supported by high frequency bands is 0° to 30°.
• For downtilt from 26.25° to 30°: Delete four layers of beams.
• For downtilt from 18.75° to 26.25°: Maintain one layer of beams at the cell center.
• For downtilt 18.75° to 11.25°: Delete two layers of beams at the cell edge.
• For downtilt 11.25° to 3.75°: Delete one layer of beams at the cell edge.
• For downtilt from 0° to 3.75°: No beams are deleted.

As shown in the preceding figures, if the downtilt adjustment range is 3.75°, beams of the outmost layer are deleted.

Copyright © 2018 Huawei Technologies Co., Ltd. All rights reserved. Page 33
Contents
3. High-Frequency Beam Management
3.1 Overview

3.2 Broadcast Beams

3.3 Tilt Adjustment

3.4 User-Level Beam Management

Copyright © 2018 Huawei Technologies Co., Ltd. All rights reserved. Page 34
User-Level Beam Management
gBS/UE rough sweeping gNodeB uses SSB for cell-
(Step-1): level wide beam sweeping,
and UE receives signals
using different wide beams.

gBS precise sweeping gNodeB uses CSI-RS for


(Step-2): narrow beam sweeping, and
UE receives signals using the
optimal wide beam.

UE precise sweeping gNodeB uses precise CSI-


(Step-3): RS beam, and UE receives
signals using several narrow
beams.

Copyright © 2018 Huawei Technologies Co., Ltd. All rights reserved. Page 35
Contents
1. Beam Management Overview

2. Low-Frequency Beam Management

3. High-Frequency Beam Management

4. Feature Activation

5. Related Monitoring Items

Copyright © 2018 Huawei Technologies Co., Ltd. All rights reserved. Page 36
Feature Activation
1. Basic 3D coverage (scenario-based broadcast beams)

Parameter Meaning Parameter ID Setting Notes


By default, only the default scenario is supported. Licenses are required
for the configuration of other scenarios.
NRDUCellTrpBeam.Coverage
Scenario Before the configuration, run the DSP NRDUCELLTRP command to
Scenario
query the scenarios supported by the AAU.
Changing the scenario will cause the cell to reset.
For low frequencies, it is recommended that this parameter be set to the
preset tilt (6°) to obtain the maximum beam gains.
Tilt NRDUCellTrpBeam.Tilt
For high frequencies, it is recommended that this parameter be set to
0°. Changing the tilt will cause the cell to reset.
Azimuth NRLoCellRsvdParam.Azimuth It is recommended that this parameter be set to 0°.

2. Configuration for user-level beam scanning


//Configuring SINR threshold for beam scanning transition from SRS to CSI-RS
MOD NRDUCELLRSVDPARAM: NrLocalCellId=1, Rsvd8Param50=-15dB;
//Configuring the distance between the beam and the optimal beam for CSI-RS beam scanning
MOD NRDUCELLRSVDPARAM: NrLocalCellId=1, Rsvd8Param51=2;

Copyright © 2018 Huawei Technologies Co., Ltd. All rights reserved. Page 37
Contents
1. Beam Management Overview

2. Low-Frequency Beam Management

3. High-Frequency Beam Management

4. Feature Activation

5. Related Monitoring Items

Copyright © 2018 Huawei Technologies Co., Ltd. All rights reserved. Page 38
Basic 3D Coverage Feature Observation
This feature is enabled by default. You can run LST NRDUCELLTRPBEAM command to query the configured beam scenario and tilt.
Trace the UE and observe the RSRP corresponding to the optimal beam. Then, determine whether the beam scenario takes effect.
For example, if the UE locates at the normal direction of the vertical beam as shown in the following figure, when the H105V6 scenario is
changed to the H110V25 scenario, you can observe that the RSRP reported by the UE after the change is higher than the RSRP reported
by the UE before the change.
The beam ID is also changed from 4 to 3.

3 4 5
2 6 3 4
2 5
1 7 1
6
0
0 7

H105V6 H110V25
Copyright © 2018 Huawei Technologies Co., Ltd. All rights reserved. Page 39
Beam Management External CHR
Cell Tracing Recording Event Description
Event Name Event & Parameter Meaning
Event ID Mode and Parameters

Statistics on downlink service traffic at the MAC layer collected based


Private event |
PERIOD_PRIVATE_B Fixed period: 15 on beams (including initial transmission and retransmission service
0x01008002 real-time stream
EAM_TRAFFIC CELL minutes traffic, which is calculated based on cell-level beams) (TDD only)
| SIG log
For unused beams, this field is set to an invalid value.

Private event |
BEAM_NOISE_TRAC Fixed period: 15 Average and maximum values of beam-based interference (cell-level)
0x01008003 real-time stream
KING minutes (TDD only)
| SIG log
Private event |
PERIOD_PRIVATE_B Fixed period: 15 Number of synchronized UEs using the static beams ID0 to ID127. Each
0x01008005 real-time stream
EAM_SYN_UE_NUM minutes UE is counted only in the optimal beam.
| SIG log

User-defined periodic L2 measurement event in a gNodeB


After the event is subscribed, the measurement results of the following
will be recorded based on the L2 user instance period.
BeamSwitchNum: optimal beam handover times (The optimal beams
Private period |
PERIOD_PRIVATE_U obtained through TRX sorting are selected on high frequency bands.)
0x01000003 real-time stream
E_MEASUREMENT CsiRs_Beam1_ID: ID of the first beam reported by the UE (four in total)
| SIG log
CsiRs_Beam1_Rsrp: RSRP of the first beam reported by the UE (four in
total)
Ssb_Beam_ID: ID of the SSB beam reported by the UE
Ssb_Rsrp: RSRP of the SSB beam reported by the UE

Copyright © 2018 Huawei Technologies Co., Ltd. All rights reserved. Page 40
Beam Management-related Monitoring Items
(Performance Monitoring)
Optimal beam ID and RSRP of each TRX on high frequency bands

Monitoring Item English Name Description


Indicates the ID of the optimal downlink beam at
TRX0DlOptBeamID TRX0_DlOptBeamID
the detection reporting time.
Indicates the RSRP corresponding to the optimal
TRX0DlOptBeamRsrp TRX0_DlOptBeamRsrp
downlink beam at the detection reporting time.
Indicates the ID of the optimal uplink beam at the
TRX0UlOptBeamID TRX0_UlOptBeamID
detection reporting time.
Indicates the RSRP corresponding to the optimal
TRX0UlOptBeamRsrp TRX0_UlOptBeamRsrp
uplink beam at the detection reporting time.

Copyright © 2018 Huawei Technologies Co., Ltd. All rights reserved. Page 41
Thinking
Question:
What's the specific impact of a faulty AAU dipole? Are there any disaster recovery measures? Is it
necessary to replace the entire AAU?
Answer:
A few faulty channels (64T64R) have limited negative impacts on the performance. The AAU can still
be used.
This issue can be handled using an algorithm and setting the weight of damaged channels to zero.
However, the orthogonality of the MU must be protected from being affected.
An alarm will be generated if the number of faulty channels reaches a specified threshold. In this
case, you need to replace the AAU.
If the number of faulty high-frequency channels reaches a specified threshold, an alarm is reported,
and 4T is rolled back to 2T.

Copyright © 2018 Huawei Technologies Co., Ltd. All rights reserved. Page 42
Thank You
www.huawei.com

You might also like