MAKING MODERN LIVING POSSIBLE

Datasheets

Danfoss Reciprocating compressors

MT / MTZ / MPZ / NTZ

FRCC.UD.130903.235631
www.danfoss.com/odsg
 Datasheet, technical data Maneurop reciprocating compressor, MT064-4

General Characteristics
Model number (on compressor nameplate) MT64HM4D
Code number for Industrial pack** MT64-4M
Drawing number 8502014e Dimensions
Suction and discharge connections Rotolock
Suction connection 1-3/4 " Rotolock
Discharge connection 1-1/4 " Rotolock
Suction connection with supplied sleeve 7/8 " ODF
Discharge connection with supplied sleeve 3/4 " ODF
Oil sight glass None
Oil equalisation connection None
Oil drain connection None
LP gauge port Schrader
IPR valve 30 bar / 8 bar
Cylinders 2
Swept volume 107,71 cm3/rev
Displacement @ Nominal speed 18.7 m3/h @ 2900 rpm - 22.6 m3/h @ 3500 rpm
D=288 mm
Net weight 39 kg
H=413 mm
Oil charge 1,8 litre, Mineral - 160P
H1=265 mm
Maximum system test pressure Low Side / High side 25 bar(g) / 30 bar(g)
H2=74 mm
Maximum differential test pressure 30 bar
Maximum number of starts per hour 12
Refrigerant charge limit 5 kg
Approved refrigerants R22, R417A-160PZ Terminal box

Electrical Characteristics
Nominal voltage 380-400V/3/50Hz - 460V/3/60Hz
Voltage range 340-440 V @ 50Hz - 414-506 V @ 60Hz
Winding resistance (between phases) +/- 7% at 25ºC 2.39 #
Maximum Continuous Current (MCC) 14 A
Locked Rotor Amps (LRA) 64 A
Motor protection Internal overload protector

Recommended Installation torques

Oil sight glass 0 Nm
Power connections / Earth connection Nm / 2 Nm
Mounting bolts 15 Nm IP55 (with cable gland)
1: Spade connectors 1/4''
Parts shipped with compressor 2: Earth M4-12
Mounting kit with grommets, bolts, nuts, sleeves and washers 3: Knock-out Ø 21 mm (0.83'')
Initial oil charge 4: Hole Ø 21 mm (0.83'')
Installation instructions

Approvals : CE certified, UL certified (file SA6873), -

*Singlepack: Compressor in cardboard box
**Industrial pack: 6 Unboxed compressors on pallet (order per multiples of 6)

Danfoss can accept no responsibility for possible errors in catalogues, brochures and other printed material. Danfoss reserves the right to alter its products without notice.
This also applies to products already on order provided that such alternations can be made without subsequential changes being necessary in specifications already agreed.
All trademarks in this material are property of the respective companies. Danfoss, the Danfoss logotype and Maneurop are trademarks of Danfoss A/S. All rights reserved.

FRCC.ED.MT064-4S.C2.02 / page technical data

RECIPROC ATING COMPRESSORS
 Datasheet, accessories and spare parts Maneurop reciprocating compressor, MT064-4

Rotolock accessories, suction side Code no.

Solder sleeve, P07 (1-3/4" Rotolock, 7/8" ODF) 8153013
Angle adapter, C07 (1-3/4" Rotolock, 7/8" ODF) 8168008
Rotolock valve, V07 (1-3/4" Rotolock, 7/8" ODF) 8168032 Gaskets, sleeves and nuts
Gasket, 1-3/4" 8156132

Rotolock accessories, discharge side Code no.

Solder sleeve, P04 (1-1/4" Rotolock, 3/4" ODF) 8153008
Angle adapter, C04 (1-1/4" Rotolock, 3/4" ODF) 8168006
Rotolock valve, V04 (1-1/4" Rotolock, 3/4" ODF) 8168029
Gasket, 1-1/4" 8156131

Rotolock accessories, sets Code no. 1: Gasket

Angle adapter set, C07 (1-3/4"~7/8"), C04 (1-1/4"~3/4") 7703013 2: Solder sleeve
Valve set, V07 (1-3/4"~7/8"), V04 (1-1/4"~3/4") 7703006 3: Rotolock nut
Gasket set, 1", 1-1/4", 1-3/4", OSG gaskets black & white 8156009

Oil / lubricants Code no.

Mineral oil, 160P, 2 litre can 7754001
Mineral oil, 160P, 5 litre can 7754002

Crankcase heaters Code no. Mounting kit

PTC heater 27W,CE mark, UL 120Z0459
Belt type crankcase heater, 65 W, 230 V, CE mark, UL 7773107
Belt type crankcase heater, 65 W, 400 V, CE mark, UL 7773117
Belt type crankcase heater, 65 W, 460 V, CE mark, UL 120Z0466

Miscellaneous accessories Code no.

Electronic soft start kit, MCI 15 C 7705006
Acoustic hood for 2 cylinder compressor 120Z0472

Spare parts Code no.

Mounting kit for 1 and 2 cylinder compressor, including 3 grommets, 3 bolts 8156001
Service kit for terminal box 80 x 96 mm, including 1 cover, 1 clamp 8156134 1: Bolt (3x)
2: Lock washer (3x)
3: Flat washer (3x)
4: Sleeve (3x)
5: Grommet (3x)
6: Nut (3x)

Danfoss can accept no responsibility for possible errors in catalogues, brochures and other printed material. Danfoss reserves the right to alter its products without notice.
This also applies to products already on order provided that such alternations can be made without subsequential changes being necessary in specifications already agreed.
All trademarks in this material are property of the respective companies. Danfoss, the Danfoss logotype and Maneurop are trademarks of Danfoss A/S. All rights reserved.

FRCC.ED.MT064-4S.C2.02 / page accessories

RECIPROC ATING COMPRESSORS
 

 
 
 
 
  
  


 
     !" #$%   &$$

   

 
   
           

'( )  *
             ! ! !  !  !
  "       "  !  !"  "  !
     "  !       " """    "
    "  !"       ! !   
     !   !         
     "  ! "  "   " "   
"       ! "  !  "  
"     " " !   !  ! " 

+
  *
    !  !"  !        " "
  "      !  "    !    
        "          
    !  "  "  "        
   !!      !    !    
        ""  !  !   
"             !" " 
"      "  ! " "  " ""

'
   ,
  ! " " "" "!   !
 "   " "" "  " !  "
 " " " "!  !    !
 " " "   ! !" ! !"
  " ""!   ! !! !  
   "    !  " !"
"     ! !!    !
"     !  "  !

 (+  -.

   "  "  ! " 
 !    !     
 !  !     ! " " !
    !  !!   
      !    
    ""  "" !   
"    "    ! !
"         " 

'

  
 
/'01
 !  "  !   " !
     !     ! "
     !!   " " !
          ! "
   ! !" !   "   
    "       !
"     ""     !
"      "    

"( 
 
  2  3'  2  3' 

+ 

#   $   % &'  () *+ , *
  -
)+
   ! % &   .) *+ , *
  -

 *  !! / .)  + *
  -
&** 0#+  12,
3)  " 4 +

4 +
 #

#  5/
6  

 
 
+   % , *  ,  5/
6 
* 

 
 
+  
7   * 6 4
,
 8  9 : 4-#  8  9 /## 
0
  ;2 <
Danfoss can accept no responsibility for possible errors in catalogues, brochures and other printed material. Danfoss reserves the right to alter its products without notice.
This also applies to products already on order provided that such alternations can be made without subsequential changes being necessary in specifications already agreed.
All trademarks in this material are property of the respective companies. Danfoss, the Danfoss logotype and Maneurop are trademarks of Danfoss A/S. All rights reserved.

5&''!'$$ . 

 
&$$  
RECIPROC ATING COMPRESSORS
 

 
 
 
 
  
  


 
     !"#   "$$

   

 
   
           

%& '  (
     !  "    !! ! !  "  
  !   " " ! "     !      " !
  "  " " !      " "    
    "     "      !!  !"
   !  " "  ! !  !      "
     !  !  !   "   
    !  !       ! 
     "  !      " 

)
  (
  !"  !    "  ""        !!
    "        "  "    
  !  "!    !  "  !!    ""  "
  !"    "    !"  "    "  !
     "  "!    "      "
      !   "    !"  "!!
     !!  "       
          !! " 

%
   !
      " ! "" " "
   !    ! " " " " "
      "" " "" "!" 
    ! " " "    "
     " "" "  ! !
   " " "! ! ! ! !
    "  " ! !!" 
      ! !"  

 &)  *+

 !       "!  "
    !"   "  "
 "  " !  !"    
 "     "   
  !  "  " ! ! 
          ! "
        "! 
     !  !   "

%

  
 
,%-.
 !     "     ""!
  !   !   " "  "
 !     "    ! "
    !   !    !
   "   " "  " 
    ""  ! " "  
       ! " 
        " "

/& 
 
  0 1$ 2%  0  2% 

) 

#   $  " % &'  () *+ , *
 "" -
)+
   " % &   .) *+ , *
  -

 *  ! / .)  + *
 ! -
&** 0#+ " 12,
3) ! 3 )

4 +
 #

#  5/
6  

 
 
+   % , *  ,  5/
6 
* 

 
 
+  
7   * 6 4
,
 8  9 : 4-#  8  9 /## 
0
  ;2 <
Danfoss can accept no responsibility for possible errors in catalogues, brochures and other printed material. Danfoss reserves the right to alter its products without notice.
This also applies to products already on order provided that such alternations can be made without subsequential changes being necessary in specifications already agreed.
All trademarks in this material are property of the respective companies. Danfoss, the Danfoss logotype and Maneurop are trademarks of Danfoss A/S. All rights reserved.

4"%%5%$$ + 

 
"$$  
RECIPROC ATING COMPRESSORS
Datasheet, drawing Maneurop scroll compressor

E
8502014
COMPRESSOR 2 CYLINDERS
WITHOUT OIL EQUALISATION

Danfoss can accept no responsibility for possible errors in catalogues, brochures and other printed material. Danfoss reserves the right to alter its products without notice.
This also applies to products already on order provided that such alternations can be made without subsequential changes being necessary in specifications already agreed.
All trademarks in this material are property of the respective companies. Danfoss, the Danfoss logotype and Maneurop are trademarks of Danfoss A/S. All rights reserved.

FRCC.PD.8502014E / page drawings

 Datasheet, technical data Maneurop reciprocating compressor, MT064-4

General Characteristics
Model number (on compressor nameplate) MT64HM4DVE
Code number for Singlepack* MT64-4VI
Code number for Industrial pack** MT64-4VM Dimensions
Drawing number 8502012g
Suction and discharge connections Rotolock
Suction connection 1-3/4 " Rotolock
Discharge connection 1-1/4 " Rotolock
Suction connection with supplied sleeve 7/8 " ODF
Discharge connection with supplied sleeve 3/4 " ODF
Oil sight glass Threaded
Oil equalisation connection 3/8'' flare SAE
Oil drain connection None
LP gauge port Schrader
IPR valve 30 bar / 8 bar
Cylinders 2
Swept volume 107,71 cm3/rev
D=288 mm
Displacement @ Nominal speed 18.7 m3/h @ 2900 rpm - 22.6 m3/h @ 3500 rpm
H=413 mm
Net weight 39 kg
H1=265 mm
Oil charge 1,8 litre, Mineral - 160P
H2=74 mm
Maximum system test pressure Low Side / High side 25 bar(g) / 30 bar(g)
Maximum differential test pressure 30 bar
Maximum number of starts per hour 12
Refrigerant charge limit 5 kg Terminal box
Approved refrigerants R22, R417A-160PZ

Electrical Characteristics
Nominal voltage 380-400V/3/50Hz - 460V/3/60Hz
Voltage range 340-440 V @ 50Hz - 414-506 V @ 60Hz
Winding resistance (between phases) +/- 7% at 25ºC 2.39 #
Maximum Continuous Current (MCC) 14 A
Locked Rotor Amps (LRA) 64 A
Motor protection Internal overload protector

Recommended Installation torques

Oil sight glass 50 Nm
Power connections / Earth connection Nm / 2 Nm IP55 (with cable gland)
Mounting bolts 15 Nm 1: Spade connectors 1/4''
2: Earth M4-12
Parts shipped with compressor 3: Knock-out Ø 21 mm (0.83'')
Mounting kit with grommets, bolts, nuts, sleeves and washers 4: Hole Ø 21 mm (0.83'')
Suction & Discharge solder sleeves, rotolock nuts and gaskets (shipped with rotolock version only)
Initial oil charge
Installation instructions

Approvals : CE certified, UL certified (file SA6873), CCC certified

*Singlepack: Compressor in cardboard box
**Industrial pack: 6 Unboxed compressors on pallet (order per multiples of 6)

Danfoss can accept no responsibility for possible errors in catalogues, brochures and other printed material. Danfoss reserves the right to alter its products without notice.
This also applies to products already on order provided that such alternations can be made without subsequential changes being necessary in specifications already agreed.
All trademarks in this material are property of the respective companies. Danfoss, the Danfoss logotype and Maneurop are trademarks of Danfoss A/S. All rights reserved.

FRCC.ED.MT064-4V.C2.02 / page technical data

RECIPROC ATING COMPRESSORS
 Datasheet, accessories and spare parts Maneurop reciprocating compressor, MT064-4

Rotolock accessories, suction side Code no.

Solder sleeve, P07 (1-3/4" Rotolock, 7/8" ODF) 8153013
Angle adapter, C07 (1-3/4" Rotolock, 7/8" ODF) 8168008
Rotolock valve, V07 (1-3/4" Rotolock, 7/8" ODF) 8168032 Gaskets, sleeves and nuts
Gasket, 1-3/4" 8156132

Rotolock accessories, discharge side Code no.

Solder sleeve, P04 (1-1/4" Rotolock, 3/4" ODF) 8153008
Angle adapter, C04 (1-1/4" Rotolock, 3/4" ODF) 8168006
Rotolock valve, V04 (1-1/4" Rotolock, 3/4" ODF) 8168029
Gasket, 1-1/4" 8156131

Rotolock accessories, sets Code no. 1: Gasket

Angle adapter set, C07 (1-3/4"~7/8"), C04 (1-1/4"~3/4") 7703013 2: Solder sleeve
Valve set, V07 (1-3/4"~7/8"), V04 (1-1/4"~3/4") 7703006 3: Rotolock nut
Gasket set, 1", 1-1/4", 1-3/4", OSG gaskets black & white 8156009

Oil / lubricants Code no.

Mineral oil, 160P, 2 litre can 7754001
Mineral oil, 160P, 5 litre can 7754002

Crankcase heaters Code no. Mounting kit

PTC heater 27W,CE mark, UL 120Z0459
Belt type crankcase heater, 65 W, 230 V, CE mark, UL 7773107
Belt type crankcase heater, 65 W, 400 V, CE mark, UL 7773117
Belt type crankcase heater, 65 W, 460 V, CE mark, UL 120Z0466

Miscellaneous accessories Code no.

Electronic soft start kit, MCI 15 C 7705006
Acoustic hood for 2 cylinder compressor 120Z0472
Oil equalisation nut 8153127

Spare parts Code no.

Mounting kit for 1 and 2 cylinder compressor, including 3 grommets, 3 bolts 8156001 1: Bolt (3x)
Oil sight glass with gaskets (black & white) 8156019 2: Lock washer (3x)
Gasket for oil sight glass (black chloroprene) 8156145 3: Flat washer (3x)
Service kit for terminal box 80 x 96 mm, including 1 cover, 1 clamp 8156134 4: Sleeve (3x)
5: Grommet (3x)
6: Nut (3x)

Danfoss can accept no responsibility for possible errors in catalogues, brochures and other printed material. Danfoss reserves the right to alter its products without notice.
This also applies to products already on order provided that such alternations can be made without subsequential changes being necessary in specifications already agreed.
All trademarks in this material are property of the respective companies. Danfoss, the Danfoss logotype and Maneurop are trademarks of Danfoss A/S. All rights reserved.

FRCC.ED.MT064-4V.C2.02 / page accessories

RECIPROC ATING COMPRESSORS
 

 
 
 
 
  
  


 
     !" #$%   &$$

   

 
   
           

'( )  *
             ! ! !  !  !
  "       "  !  !"  "  !
     "  !       " """    "
    "  !"       ! !   
     !   !         
     "  ! "  "   " "   
"       ! "  !  "  
"     " " !   !  ! " 

+
  *
    !  !"  !        " "
  "      !  "    !    
        "          
    !  "  "  "        
   !!      !    !    
        ""  !  !   
"             !" " 
"      "  ! " "  " ""

'
   ,
  ! " " "" "!   !
 "   " "" "  " !  "
 " " " "!  !    !
 " " "   ! !" ! !"
  " ""!   ! !! !  
   "    !  " !"
"     ! !!    !
"     !  "  !

 (+  -.

   "  "  ! " 
 !    !     
 !  !     ! " " !
    !  !!   
      !    
    ""  "" !   
"    "    ! !
"         " 

'

  
 
/'01
 !  "  !   " !
     !     ! "
     !!   " " !
          ! "
   ! !" !   "   
    "       !
"     ""     !
"      "    

"( 
 
  2  3'  2  3' 

+ 

#   $   % &'  () *+ , *
  -
)+
   ! % &   .) *+ , *
  -

 *  !! / .)  + *
  -
&** 0#+  12,
3)  " 4 +

4 +
 #

#  5/
6  

 
 
+   % , *  ,  5/
6 
* 

 
 
+  
7   * 6 4
,
 8  9 : 4-#  8  9 /## 
0
  ;2 <
Danfoss can accept no responsibility for possible errors in catalogues, brochures and other printed material. Danfoss reserves the right to alter its products without notice.
This also applies to products already on order provided that such alternations can be made without subsequential changes being necessary in specifications already agreed.
All trademarks in this material are property of the respective companies. Danfoss, the Danfoss logotype and Maneurop are trademarks of Danfoss A/S. All rights reserved.

5&''!'$$ . 

 
&$$  
RECIPROC ATING COMPRESSORS
 

 
 
 
 
  
  


 
     !"#   "$$

   

 
   
           

%& '  (
     !  "    !! ! !  "  
  !   " " ! "     !      " !
  "  " " !      " "    
    "     "      !!  !"
   !  " "  ! !  !      "
     !  !  !   "   
    !  !       ! 
     "  !      " 

)
  (
  !"  !    "  ""        !!
    "        "  "    
  !  "!    !  "  !!    ""  "
  !"    "    !"  "    "  !
     "  "!    "      "
      !   "    !"  "!!
     !!  "       
          !! " 

%
   !
      " ! "" " "
   !    ! " " " " "
      "" " "" "!" 
    ! " " "    "
     " "" "  ! !
   " " "! ! ! ! !
    "  " ! !!" 
      ! !"  

 &)  *+

 !       "!  "
    !"   "  "
 "  " !  !"    
 "     "   
  !  "  " ! ! 
          ! "
        "! 
     !  !   "

%

  
 
,%-.
 !     "     ""!
  !   !   " "  "
 !     "    ! "
    !   !    !
   "   " "  " 
    ""  ! " "  
       ! " 
        " "

/& 
 
  0 1$ 2%  0  2% 

) 

#   $  " % &'  () *+ , *
 "" -
)+
   " % &   .) *+ , *
  -

 *  ! / .)  + *
 ! -
&** 0#+ " 12,
3) ! 3 )

4 +
 #

#  5/
6  

 
 
+   % , *  ,  5/
6 
* 

 
 
+  
7   * 6 4
,
 8  9 : 4-#  8  9 /## 
0
  ;2 <
Danfoss can accept no responsibility for possible errors in catalogues, brochures and other printed material. Danfoss reserves the right to alter its products without notice.
This also applies to products already on order provided that such alternations can be made without subsequential changes being necessary in specifications already agreed.
All trademarks in this material are property of the respective companies. Danfoss, the Danfoss logotype and Maneurop are trademarks of Danfoss A/S. All rights reserved.

4"%%5%$$ + 

 
"$$  
RECIPROC ATING COMPRESSORS
Datasheet, drawing Maneurop scroll compressor

G
COMPRESSOR 2 CYLINDERS
8502012
WITH OIL EQUALIZATION

Danfoss can accept no responsibility for possible errors in catalogues, brochures and other printed material. Danfoss reserves the right to alter its products without notice.
This also applies to products already on order provided that such alternations can be made without subsequential changes being necessary in specifications already agreed.
All trademarks in this material are property of the respective companies. Danfoss, the Danfoss logotype and Maneurop are trademarks of Danfoss A/S. All rights reserved.

FRCC.PD.8502012G / page drawings